Datasheet

CCD multichannel detector heads
C7043
C7044
Designed for back-thinned CCD area image
sensor
The C7043 and C7044 are high sensitivity multichannel detector heads for use with back-thinned FFT-CCD area image sensors (S7033/
S7034 series) that offer large full well capacity. The C7043 is designed for the non-cooled back-thinned type (S7033 series), while
the C7044 for the one-stage TE-cooled type (S7034 series) for detection at even lower light levels. Both the C7043 and C7044 incorporate a low-noise driver/amplifier circuit that provides reliable operation from simple external signals. The C7044 also includes a
highly stable temperature controller that cools the sensor to a preset temperature level (Ts=-10 °C) as soon as the power is turned
on. If the cooler fails and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the
thermoelectric cooler. Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers.
Controller for multichannel detector head C7557-01 is also available. The software supplied with the C7557-01 allows easy control of
the multichannel detector head and data acquisition.
Features
Applications
Designed for back-thinned CCD area image sensor *1
C7043: for non-cooled type
C7044: for TE-cooled type
Fluorescence spectroscopy
Line binning operation *2/area scanning operation
Raman spectroscopy
Other low-light-level detection
Driver/amplifier circuit for low noise CCD operation
Highly stable temperature controller (C7044)
Cooling temperature: -10 °C ± 0.05 °C
Simple signal input operation
Compact configuration
Selection guide
The table below shows CCD area image sensors applicable for the C7043 and C7044.
Since the C7043 and C7044 do not include a CCD area image sensor, so select the desired sensor and order it separately.
CCD Area image sensor
Type No.
C7043
C7044
Type No.
Number of pixels
Number of active pixels
S7033-0907
S7033-1007
S7034-0907S
S7034-1007S
532 × 128
1044 × 128
532 × 128
1044 × 128
512 × 122
1024 × 122
512 × 122
1024 × 122
Active area
[mm (H) × mm (V)]
12.288 × 2.928
24.576 × 2.928
12.288 × 2.928
24.576 × 2.928
*1: In normal CCD image sensors that receive light from the front surface, the active area is covered with electrodes for charge transfer.
These electrodes cut off UV radiation incident on the image sensor and also reduce the quantum efficiency. In contrast, back-thinned
CCD image sensors have a unique structure in which the back of the active area is finely ground to allow light to enter from the back
surface. This structure ensures high UV sensitivity and quantum efficiency because incident light need not pass through the electrodes.
*2: The CCD area image sensor can be operated like a linear image sensor having a large active area by transferring all the pixel signals in
the vertical direction to the horizontal register (this is referred to as line binning).
www.hamamatsu.com
1
CCD multichannel detector heads
C7043, C7044
Absolute maximum ratings
Parameter
Supply voltage (for digital circuitry)
Supply voltage (for analog circuitry)
Supply voltage
Digital input voltage
Operating temperature
Storage temperature
Symbol
VD1, VD2
VA1+
VA1VA2
Vp
VF
-
C7043
C7044
C7043
C7044
Topr
Tstg
Min.
-0.5
0
+10
-20
0
Typ.
-
Max.
+7
+18
-18
+30
+7
+14
VD1
+50
+35 *3
+70
+50
Unit
V
°C
*3: The maximum value may be lower, depending on the drive frequency and the number of sensor pixels.
Electrical characteristics
(Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V, unless otherwise noted)
Parameter
High level
Low level
Digital input
CLK frequency
Data video readout frequency
Start pulse width
High level (IO=-6 mA)
Low level (IO=+6 mA)
Digital output
Symbol
VIH
VIL
fCLK
fv
tst
VIH
VIL
Min.
+2.0
-0.5
1/fCLK
+2.0
-
Typ.
-
Max.
VD (1, 2)
+0.8
1
fCLK/4
+0.8
Unit
V
V
MHz
Hz
s
V
V
VD1
VA1+
VA1VA2
VD2
Vp
VF
-
+4.75
+14.5
-14.5
+23.5
+4.75
+4.75
+11.75
-
+5.0
+15.0
-15.0
+24.0
+5.0
+5.0
+12.0
+100
+5.25
+15.5
-15.5
+24.5
+5.25
+5.25
+12.25
+200
+100
-100
+30
+30
+2.5
-
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
A
mA
Power supply operating conditions
Digital circuitry
Analog circuitry
Voltage
Other *4
VD1 (+5 VDC)
VA1+ (+15 VDC)
VA1- (-15 VDC)
VA2 (+24 VDC)
VD2 (+6 VDC) *4
Vp (+6 VDC) *4
VF (+12 VDC) *4
Current
*4: C7044
Electrical and optical characteristics
(Ta=25 °C, Ts=-10 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V)
Parameter
Symbol
SR
Spectral response range
Full well capacity
Vertical
Horizontal
Conversion gain *5
Dark current *6
Fw
Sv
C7043
C7044
Readout noise
Dynamic range
Photo response non-uniformity *7
DS
Nr
DR
PRNU
Min.
180
-
Typ.
200 to 1100
360
3400
3
100
3
60
56667
±3
Max.
1000
30
±10
Unit
nm
keμV/ee-/pixel/s
e- rms
%
*5: Including the circuit gain
*6: Horizontal register value
*7: Measured at 50 % of the full well capacity
2
CCD multichannel detector heads
C7043, C7044
Specifications for temperature controller (C7044)
(Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V)
Parameter *8
Cooling temperature
Temperature control range
Power dissipation of TE-cooler element
Cool down time to reset temperature
Setting temperature for overheat protection *9
Symbol
Ts
ΔTs
Pp
to
To
Min.
-11
-0.05
-
Typ.
-10
+45
Max.
-9
+0.05
7
5
-
Unit
°C
°C
W
min.
°C
*8: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor.
*9: Temperature of rear-side of housing (part to fix fan)
Spectral response
Dark current vs. temperature
(Typ. Ta=25 °C)
100
90
BACKthinned
CCD
100
Dark current (e-/pixel/s)
Quantum efficiency (%)
80
70
60
50
40
30
Frontilluminated
CCD
20
(Typ.)
1000
10
1
0.1
10
0
200
400
600
800
1000
0.01
-50
1200
Wavelength (nm)
-40
-30
-20
-10
0
10
20
30
Temperature (°C)
KMPDB0038EA
KMPDB0256EA
Block diagram (S7033/S7034 series)
Thinning
23
21
15
20
13
14
2-bevel
22
n
H
1
2 signal out
5
4
3
2
12345
24
4-bevel
Thinning
V
12
2
11
3
4
5
8
10
9
n
Blank (4 pixels)
Blank (4 pixels)
2 signal out
6-bevel
V=58, 122, 250
H=512, 1024
6-bevel
KMPDC0016EB
3
CCD multichannel detector heads
C7043, C7044
Block diagram (C7044)
P+
Vp (+5 V)
P.GND
VD2 (+5 V)
D.GND
PLED
TH+
TH-
VF (+12 V)
F.GND
Temp monitor
Cooling control
VD1 (+5 V)
D.GND
VA1+ (+15 V)
VA1- (-15 V)
A.GND
Temperature controller *
TE-cooler
OD
RD
OG
IG1H, IG2H
IG1V, IG2V
P1V, P2V, TG
P1H, P2H
SG
RG
TH.H
Regulator
VDD
VA2 (+24 V)
Start
CLK
VEE
Driver
Timing
generator
EOS
Trigger
Mode select
SS, ISV, ISH
Buffer
Data video
OS
Pre-amp
Inverter
CCD area image sensor
S7034 series
Clamp
Low-pass
filter
* The C7043 does not include the temperature controller and TE-cooler.
KACCC0114EB
Timing chart (line binning operation)
Start
CLK
P1V
P2V
TG
P1H
P2H
SG
RG
Clamp
EOS
Trigger
Data video
V-ch1
H-ch10
H-ch11
V-ch2
H-ch(N-10) H-ch(N-9)
V-ch(M)
H-ch1
H-ch2
H-ch(N)
M=128 N=532, 1044
V-ch1--V-ch2, V-ch (M-3)--V-ch (M): Isolation pixels
H-ch1--H-ch4, H-ch (N-3)--H-ch (N): Blank pixels
KACCC0115EC
KACCC0115EC
4
CCD multichannel detector heads
C7043, C7044
Pin connections of "SIGNAL I/O" connector
15-pin D-sub connector
8
7
15
6
14
5
13
4
12
3
11
2
10
1
9
KACCC0069EA
Pin No.
Terminal name
1
Mode select
2
3
4
5
Data video
VA1+ (+15 V)
VA1- (-15 V)
VD1 (+5 V)
6
Start
7
CLK
8
EOS
9
10
11
12
13
14
15
A.GND
A.GND
VA2 (+24 V)
D.GND
D.GND
D.GND
Trigger
Description
Digital input signal used to select between the line binning operation and area scanning operation.
HCMOS compatible.
High level or left open: line binning operation
Low level: area scanning operation
Analog video output. Positive polarity.
Analog power supply
Analog power supply
Digital power supply
Digital input signal for initializing the circuit.
HCMOS compatible. Positive logic.
The interval of the Start pulses determines the integration time of the CCD image sensor.
Digital input signal for operating the circuit.
HCMOS compatible. Rising edge operation.
Digital output signal for indicating end-of-scan of the image sensor.
HCMOS compatible. Negative logic.
Analog ground
Analog ground
Analog power supply
Digital ground
Digital ground
Digital ground
Digital output signal for A/D conversion. HCMOS compatible. Positive logic.
Pin connections of "TE CONTROL I/O" connector (C7044)
9-pin D-sub connector
5
4
9
3
8
2
7
1
6
KACCC0075EA
Pin No.
1
2
Terminal name
VD2 (+5 V)
Temp monitor
3
Cooling control
4
5
6
7
8
9
Vp (+5 V)
VF (+12 V)
D.GND
D.GND
P.GND
F.GND
Description
Digital power supply
Analog output signal of the temperature of the CCD image sensor
Digital input signal for starting to cool down. HCMOS compatible.
High level or left open: cooling
Low level: stand-by
Power supply for the thermoelectric cooler in the CCD image sensor
Power supply for cooling fan
Ground for temperature control circuit
Ground for temperature control circuit
Power supply return of the thermoelectric cooler mounted in the CCD image sensor
Power supply return for cooling fan
Available for using same power supply (+5 V) for "+VD2" and "+Vp".
Caution: Do not connect "VD2" and "Vp" together on the backside of the 9-pin D-sub connector.
These may be connected (shorted) at the power supply end, not 9-pin D-sub connector.
5
CCD multichannel detector heads
C7043, C7044
Dimensional outlines (unit: mm)
C7043
0.5
0.3
34.0
2.7
Focal
plane
11.0
62.0
Focal
plane
82.0
50.0
80.0
60.0
90.0
100.0
50.0
(4 ) M3 depth 4
KACCA0081EC
35.0 *
C7044
34.0
2.4
0.5
Focal
plane
77.0
62.0
Focal
plane
11.0
82.0
50.0
80.0
60.0
90.0
100.0
50.0
(4 ) M3 depth 4
* The part is removable.
KACCA0082EC
Pin connections
TE controller
Power supply
Controller
VF (+12 V)
F.GND
VP (+5 V)
P.GND
VD2 (+5 V)
D.GND
Cooling control
D.GND
5
9
4
8
3
7
6
2
1
I/O signal
Pulse generator
Power supply
CLK
D.GND
Start
D.GND
VD1 (+5 V)
D.GND
VA1+ (+15 V)
VA1- (-15 V)
VA2 (+24 V)
A.GND
Controller
Mode select
D.GND
S/H or A/D
Analog input
A.GND
S/H input
D.GND
Oscilloscope
CH1
GND
Ext.Trig
GND
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
KACCC0076EB
6
CCD multichannel detector heads
C7043, C7044
Multichannel detector head controller C7557-01
When connected to a HAMAMATSU multichannel detector head and a personal computer, the C7557-01 allows easy control of the detector
head and data acquisition by using dedicated software that comes with the unit.
Suitable multichannel detector head
C7020/-02, C7021/-02, C7025/-02,
C7040, C7041, C7043, C7044, C7180,
C7181, C8061-01, C8062-01, C10150, C10151,
C5964 series, C8892
Accessories
· Spare fuse (2.5 A) *10
· AC cable
· 2 to 3 conversion adapter
· USB cable
· Detector head connection cables (for “SIGNAL I/O” and
“TE CONTROL I/O” terminal of multichannel detector head)
· CD-R (MCD USB driver, software, operation manual)
· MOS adapter *11
*10: Contained in the holder just above the AC cable connector on the C7557-01 rear panel.
*11: When operating the NMOS multichannel detector head, always be sure to attach the MOS adapter (supplied) to the C7557-01 main
unit. If the the NMOS multichannel detector head is connected and the power is turned on without attaching the adapter, the power
supply in the C7557-01 main unit may be damaged.
MOS ŢťŢűŵŦų
MOS adapter mounting example
7
CCD multichannel detector heads
C7043, C7044
Connection example
Shutter *
timing pulse
AC cable (100 to 240 V; included with the C7557-01)
Trig.
POWER
Dedicated cable
(Included with the C7557-01)
SIGNAL I/O
USB cable
(Included with
the C7557-01)
TE CONTROL I/O
Image sensor
+
Multichannel
detector head
C7557-01
PC (Windows 2000/XP/Vista)
(USB 2.0)
* Shutter, etc. are not available.
KACCC0402EA
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions.
Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2009 Hamamatsu Photonics K.K.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741
Cat. No. KACC1049E06 Mar. 2009 DN
8
Similar pages