DATASHEET

ISL6720A
®
Data Sheet
August 23, 2007
100V Triple Linear Bias Supply
Features
The ISL6720A is a low cost linear regulator for generating a
low voltage bias supply from intermediate distributed
voltages commonly used in telecom and datacom
applications. It produces three separate outputs, an
adjustable 0V to 20V output rated at up to 125mA which can
be back-biased from an external source such as an auxiliary
transformer winding, a 50mA switched regulated output
adjustable between 0V and 15V, and a fixed continuous 5V
output rated at 25mA.
• 100V Input Capability
The ISL6720A may be used as a start-up or a continuous
low power regulator. When operating as a start-up regulator,
it is capable of sourcing over 100mA from a 100V source for
short durations. This period of time allows the power supply
to start-up and provide a low voltage alternate power source,
such as the output of a transformer winding, to the VIO
output. This allows the remaining outputs to be operated
from a lower source voltage thereby minimizing power loss.
PART
MARKING
ISL6720AARZ* 67 20AARZ
TEMP.
RANGE
(°C)
-40 to +105
PACKAGE
(Pb-Free)
11 Ld DFN
PKG.
DWG.
#
L11.4x4
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on
reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach
materials and 100% matte tin plate PLUS ANNEAL - e3 termination
finish, which is RoHS compliant and compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020.
1
• Adjustable Auxiliary Winding Regulator with 40V
Withstand Capability
• Up to 125mA Combined Output Current on Switched and
Unswitched Outputs
• 250μs Delayed Start (VIO, VSW) after Continuous
(VCONT) Output
• Regulated Switched (VSW) and Unswitched Outputs
(VIO)
• 5V @ 25mA Continuous Output (VCONT)
• 2-Stage Over-Temperature Protection
• Package Compliant with IPC2221A, Creepage and
Clearance Spacing Requirements
• Pb-Free Available (RoHS Compliant)
Applications
Ordering Information
PART
NUMBER
(Note)
FN6487.1
• Telecom/Datacom DC/DC Converters
• Low Power Bias Supplies
Pinout
ISL6720A
(11 LD DFN)
TOP VIEW
VPWR
1
VCONT
2
9
VADJ
VCOMP
3
8
VSW
GND
4
7
VSWCOMP
VSWADJ
5
6
ENABLE
11 VIO
10 NC
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
Functional Block Diagram
VADJ
INPUT
SELECTOR
VIO
2
VPWR
START/STOP
UV
COMPARATOR
HIGH
VOLTAGE
REGULATOR
IN
INPUT
SELECTOR
VPWR OK
+
- +140°C TEMP OK
BG +
-
VSW
OUT
POST
REGULATOR
VSWCOMP
VSWADJ
MAIN
ENABLE
GND
2-LVL TMON
+140°C ±10°C
+150°C ± 10°C
VCONT
ENABLE
ENABLE
VCONT
IN
OUT
POST
REGULATOR
POR
250μs
DELAY
FALLING EDGE
DELAY
+
+
-
VCOMP
ISL6720A
+150°C TEMP OK
FN6487.1
August 23, 2007
Typical Application
CONVERTER POWER STAGE
+VOUT
VIN-
RETURN
3
VIN+
VPWR
N/C 10
C2
1.0nF
C1
1.0µF
VIO 11
FEEDBACK
AMPLIFIER
PWM
2
VCONT
VADJ 9
3
VCOMP
VSW 8
4
GND VSWCOMP 7
5
VSWADJ ENABLE 6
U1
ISL6720A
*SIZED FOR MINIMUM ZENER BIAS
CURRENT
C3
220pF
μ-CONTROLLER
C4
1.0µF
ISL6720A
1
R1*
FN6487.1
August 23, 2007
ISL6720A
Absolute Maximum Ratings (Note 3)
Thermal Information
Supply Voltage, PWR. . . . . . . . . . . . . . . . . . . . GND -0.3V to +105V
VIO, VADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.3V to +40V
VSW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.3V to +23V
All others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.3V to +6.0V
Thermal Resistance (Typical, Notes 1, 2) θJA (°C/W) θJC (°C/W)
11 Ld DFN . . . . . . . . . . . . . . . . . . . . . .
36
2.0
Maximum Junction Temperature . . . . . . . . . . . . . . .-55°C to +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range
ISL6720AARZ. . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . 18VDC to 80VDC
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
3. All voltages are with respect to GND.
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on page 2
and “Typical Application” on page 3. 17 V < VPWR < 100V, CVSW = CVCONT = 1µF, IVCONT = -250μA,
IVSW = -500μA, VSW Enabled, TA = -40°C to +105°C (Note 4), Typical values are at TA = +25°C
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
SUPPLY VOLTAGE, VPWR
Supply Voltage
100
V
Start-Up Current, IPWR
VPWR = 12V
320
470
µA
Operating Current, IPWR
VSW Enabled, VPWR = 100V
IVIO = 0
1.3
1.7
mA
VSW Disabled, VPWR = 100V,
IVIO = 0
1.2
1.7
mA
VIO Biased Externally at 40V,
VSW Enabled, VPWR = 100V
IVSW = -50mA, IVCONT = -25mA
1.2
1.7
mA
UVLO START Threshold
VADJ = VSWADJ = 0V,
IVCONT = 0mA, VSW Disabled
12.4
16.9
V
UVLO STOP Threshold
VADJ = VSWADJ = 0V,
IVCONT = -1mA, VSW Disabled
11.5
15.3
V
Hysteresis
UVLO START to UVLO STOP
0.8
1.7
V
1.2
OUTPUT VOLTAGE VIO
IVIO = 0mA to -125mA ,
VADJ = 10V, 20V, VPWR = 48V
VSW Disabled
VADJ - 4.5
VADJ - 0.5
V
IVIO = 0mA to -10mA ,
VADJ = 10V, 20V, VPWR = 48V
VSW Disabled
VADJ - 3.5
VADJ - 0.5
V
Setpoint Range
VPWR = 48V, VSW Disabled,
IVIO = 0mA for minimum setpoint
IVIO = -125mA for max setpoint
0.5
20.0
V
Source Voltage Headroom
VPWR - VIO, minimum
VPWR = 17V, 100V
VADJ = 20V, IVIO = -125mA
VIO final = 0.95 x VIO initial
5.5
V
Maximum VOUT, Faulted VADJ
VPWR = 48V, 100V
VADJ = 40V, VSW Disabled,
IVIO = 0mA
23.0
V
Overall Accuracy
VADJ Discharge Device, VOL
VPWR = 12V, IVADJ = 10mA
Operational Current (source)
VPWR = 17V, 100V
VADJ = 15V, VSW Disabled
VIO remains greater than 10.5V
4
0.65
-125
V
mA
FN6487.1
August 23, 2007
ISL6720A
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on page 2
and “Typical Application” on page 3. 17 V < VPWR < 100V, CVSW = CVCONT = 1µF, IVCONT = -250μA,
IVSW = -500μA, VSW Enabled, TA = -40°C to +105°C (Note 4), Typical values are at TA = +25°C (Continued)
PARAMETER
TEST CONDITIONS
Current Limit
VPWR = 17V, 48V
VADJ = 15V, VSW Disabled
Maximum External Bias
VPWR = 17V, 100V
VADJ = 0V, VSWADJ = 0V,
VSW Enabled
IVIO ≤ 1.00mA
MIN
TYP
MAX
UNITS
-225
-380
-500
mA
40
V
1
µA
Load Capacitance Range
(Notes 5, 6)
0.1
VADJ Bias Current
VPWR = 100V, VSW Disabled
VADJ = 0V, 40V
-75
µF
Load Capacitance Range
(Note 5)
0.47
1.0
1.5
µF
Compensation Capacitance
(Note 5)
180
220
260
pF
Overall Accuracy
VPWR = 48V
IVSW = -500μA to -50mA
VADJ = 0V, VIO = 22V, 40V ext.
-25
OUTPUT VOLTAGE VSW
Setpoint Range
VSWADJ = 0.471V
-5
+5
%
VSWADJ = 1.000V
-3
+3
%
VSWADJ = 2.143V
-3
+3
%
VSWADJ = 0V
0
1.5
V
VSWADJ = 2.25V
15
VPWR = 48V, VADJ = 0V,
VIO = 40V ext.
Source Voltage Headroom, VIO - VSW
VPWR = 21V, VADJ = 0V,
VSW = 15V, IVSW = -50mA
VIO - VSW
VSW final = 0.95 x VSW initial
Source Voltage Headroom, VPWR - VSW
VIO = 17 V ext., VADJ = 0V,
VSW = 15V, IVSW = -50mA
VPWR - VSW
VSW final = 0.95 x VSW initial
V
1.0
Minimum Required Load
VSWADJ Discharge Device, VOL
VPWR = 48V, IVSWADJ = 10mA
VSW Disabled, VADJ = 15V
Maximum VOUT, Faulted VSWADJ
VSWADJ = 4V, VIO = 40V,
IVSW = -50mA
VSWADJ DC Gain
VSW = VADJ*GVSWADJ
Long Term Stability
TA = +125°C, 1000 hours, (Note 5)
VPWR = 48V, VSWADJ = 1.0V,
IVSW = -50mA, VADJ = 0V,
VIO = 40V ext.
Operational Current (source)
VPWR = 48V, VADJ = 0V
VIO = 17V ext., VSWADJ = 2.14V
-50
Current Limit
VPWR = 100V, VADJ = 0V
VIO = 40V ext.
-80
VSWADJ Bias Current
VPWR = 100V, VIO = 40V ext.
VSWADJ = 0V, 5V
-1.0
0.10
15.1
1.5
V
5.5
V
-500
µA
0.25
V
23
V
7
V/V
0.3
%
mA
-225
-300
mA
1.0
μA
5.075
V
OUTPUT VOLTAGE VCONT
Overall Accuracy
VPWR = 17V, 100V
IVCONT = -250μA to -25mA
VADJ = 0V, VIO = 10V, 40V ext.
TA = -40 to +105°C
5
4.925
5.000
FN6487.1
August 23, 2007
ISL6720A
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on page 2
and “Typical Application” on page 3. 17 V < VPWR < 100V, CVSW = CVCONT = 1µF, IVCONT = -250μA,
IVSW = -500μA, VSW Enabled, TA = -40°C to +105°C (Note 4), Typical values are at TA = +25°C (Continued)
PARAMETER
TEST CONDITIONS
Source Voltage Headroom VIO - VCONT
MIN
TYP
MAX
UNITS
IVCONT = -25mA, minimum
3.4
5.0
V
IVCONT = -5mA, minimum
3.1
4.5
V
-250
μA
VPWR = 48V, VADJ = 0V
VIO biased ext.
IVCONT = 0.95 x IVIO + 0.05 x IVPWR
Minimum Required Load
0.2
%
Long Term Stability
TA = +125°C, 1000 hours, (Note 5)
VPWR = 100V, VADJ = 0V
VSW Disabled, IVCONT = -25mA
Operational Current (source)
VPWR = 17V, VADJ = 0V
VSW Disabled
-25
Current Limit
VPWR = 17V, 100V, VADJ = 0V
VIO = 0V, 40V ext., VSW Disabled
-30
Output Capacitance
(Note 5)
0.47
Compensation Capacitance
(Note 5)
800
High Level Input Voltage (VIH)
% of VCONT
VPWR = 48V, VSWADJ = 2.14V
VADJ = 20V, IVIO = 0mA
54
Low Level Input Voltage (VIL)
% of VCONT
VPWR = 48V, VSWADJ = 2.14V
VADJ = 20V, IVIO = 0mA
Hysteresis
% of VCONT
VPWR = 48V, VSWADJ = 2.14V
VADJ = 20V, IVIO = 0mA
Pull-Up Resistance
VENABLE = 0V
Turn-On Delay
tVSW, 10% to tENABLE, 60%
5
50
μs
Turn-Off Delay
tVSW, 90% to tENABLE, 40%
1
15
μs
500
μs
mA
-95
-150
mA
1.0
1.5
μF
1000
1200
pF
60
66
%
34
40
46
%
16
20
24
%
ENABLE
100
kΩ
POR
Turn-On Delay
tVCONT,10% to tVPWR > UVLO,
IVCONT = 0μA
150
POR Threshold, VCONT increasing
% of VCONT
70
POR Hysteresis
89
98
%
200
mV
Thermal Shutdown 1, VSW off, VIO off
140
°C
Thermal Shutdown 1 Clear
95
°C
Hysteresis 1, Internal Protection
45
°C
Thermal Shutdown 2, VCONT off
150
°C
Thermal Shutdown 2 Clear
105
°C
Hysteresis 2, Internal Protection
45
°C
THERMAL PROTECTION
NOTES:
4. Specifications at -40°C and +105°C are guaranteed by +25°C test with margin limits.
5. Limits established by characterization and are not production tested.
6. The maximum load capacitance is limited only by practical considerations. Large values of capacitance combined with high supply voltage
(VPWR) may activate the thermal protection prior to reaching steady state operation.
6
FN6487.1
August 23, 2007
ISL6720A
Typical Performance Curves
3.5
3.5
3.3
3.3
3.1
VADJ = 15V
2.9
VADJ - VIO (V)
VADJ - VIO (V)
3.1
2.7
2.5
2.3
VADJ = 20V
VPWR = 48V
2.7
2.5 VPWR = 20V
2.3
VPWR = 80V
2.1
2.1
1.9
1.9
VADJ = 10V
1.7
1.5
2.9
1.7
0
10
20
30
40
50
60
70
80
90
100
1.5
0
10
20
30
VIO LOAD (mA)
FIGURE 1. VADJ - VIO vs IVIO @ VPWR = 25V, +25°C
50
60
70
80
90
100
FIGURE 2. VADJ - VIO vs IVIO @ VADJ = 15V, +25°C
1.001
1.002
VSW = 5.0V
NORMALIZED VSW
TEMPERATURE VARIATION
NORMALIZED VCONT
TEMPERATURE VARIATION
40
VIO LOAD (mA)
1.000
0.999
0.998
0.997
-40
-25
-10
5
20
35
50
65
80
95
110
TEMPERATURE (°C)
FIGURE 3. VCONT REGULATION vs TEMPERATURE
Pin Descriptions
VPWR - VPWR is the primary power connection for the IC.
The under voltage lockout (UVLO) feature of VPWR
enables/disables all outputs even if VIO is externally biased.
To optimize noise immunity, bypass VPWR to GND with a
ceramic capacitor as close to the VPWR and GND pins as
possible.
VCONT - A 25mA continuous output that derives its source
voltage from either VIO (when enabled and sufficient) or
VPWR (when VIO is not available). VCONT sequences on
before VIO and VSW by approximately 250μs.
The over-temperature protection feature protects VCONT at
a higher temperature than VIO and VSW. This ensures VIO
and VSW shutdown at a lower temperature and allows
VCONT to remain on.
VCOMP - A 1000pF compensating capacitor is placed
between VCOMP and VCONT to stabilize the control loop.
This value may vary depending on the output load and
capacitance applied between VCONT and GND.
7
1.001
VSW = 20V
1.000
VSW = 3.3V
0.999
0.998
-40
VSW = 12V
-25
-10
5
20
35
50
65
80
95
110
TEMPERATURE (°C)
FIGURE 4. VSW REGULATION vs TEMPERATURE
VIO - This is the unswitched low voltage output supply. It
may be used as is, or may be back-biased by an auxiliary
power source such as a transformer winding. VIO should be
bypassed to GND with a 0.1μF capacitor. Although a
minimum capacitance is not required, it does provide the
source voltage bypass for VSW and VCONT when VIO is
capable of supporting those outputs. Smaller values of
capacitance will result in larger disturbances during load
transients. Its output is adjustable from 0V to 20.0V using a
reference on VADJ, such as a zener diode and bias resistor.
VIO may be soft-started with a capacitance to ground from
VADJ.
VADJ - The feedback adjustment pin for VIO. An external
reference on VADJ sets the voltage on VIO. The reference
may be a resistor/zener diode combination from VPWR.
VADJ has a discharge device that activates momentarily
during power-up and power-down sequences to allow VIO to
be soft started.
GND - Signal and power ground connections for this device.
FN6487.1
August 23, 2007
ISL6720A
VSW - This is the switched regulated low voltage output
supply derived from VIO. Bypass to GND with a 1.0μF
capacitor. Its output is adjustable from 0V to 15.0V using an
appropriate divider from VCONT to VADJ and GND. VSW is
nominally 7 x VSWADJ. Protection circuitry prevents the
output from exceeding 23V in the event of a fault on
VSWADJ (short high). The minimum output current
capability is 50mA with transient capability to > 80mA. VSW
may be soft-started by placing a capacitor from VSWADJ to
GND.
ENABLE - The positive logic on/off control input that
controls the VSW output. A logic high enables VSW.
VSWCOMP - A 220pF compensating capacitor is placed
between VSWCOMP and VSW to stabilize the control loop.
This value may vary depending on the output load and
capacitance applied between VSW and GND.
VSWADJ - The feedback adjustment pin for VSW. A divider
from VCONT to GND sets the output voltage for VSW.
VSWADJ has a node discharge device that activates
momentarily at power-up, when disabled (ENABLE low), and
during power-down sequences. VSW is nominally
7 x VSWADJ.
on VIO gradually transfers from the VIO regulator to external
back-bias source. Depending on load, the back-bias voltage
may have to exceed the VIO setpoint by as much as 3V
before the VIO regulator is off.
The output voltage of VIO is set by applying a reference
voltage to VADJ. The reference voltage may be set by using
a resistor and zener diode combination from the VPWR
input. VIO ranges from 0.5V to 4.5V below the voltage
applied to VADJ depending on the load on VIO. VIO can
source more than 125mA for short durations, limited only by
the device power dissipation and the thermal constraints of
the application.
VIO = VADJ – V OFFSET
(EQ. 1)
V
where VOFFSET ranges from 0.5V to 4.5V.
VIN
1
VPWR
VIO 11
N/C 10
2
VCONT VADJ
9
3
VCOMP
VSW
8
Functional Description
4
GND VSWCOMP
7
Features
5
VSWADJ
ENABLE
6
The control circuitry used in Telecom/Datacom DC/DC
converters often requires an operating bias voltage
significantly lower than the source voltage available to the
converter. Many applications use a discrete linear regulator
from the input source to create the bias supply. Often an
auxiliary winding from the power transformer is used to
supplement or replace the linear supply once the converter
is operating. The auxiliary winding bias voltage may require
regulation, as well, to minimize the voltage variation inherent
in unregulated transformer winding outputs. When
implemented discretely, this circuitry occupies significant
PWB area, a considerable problem in today’s high density
converters.
The ISL6720A triple linear regulator simplifies the start-up
and operating bias circuitry needed in Telecom and Datacom
DC/DC converters by integrating these functions, and more,
in a small 4mmx4mm DFN package.
VIO
VIO is the primary output of the ISL6720A, providing bias
voltage whenever the input source voltage, VPWR, is above
its under voltage lockout (UVLO) threshold. VIO, which is an
abbreviation for “voltage input/output”, is adjustable from
0.5V to 20V using the VADJ input, and may be back-biased
up to 40V from an external source independent of VPWR.
The back-bias voltage must be higher than the VIO setpoint
to disable the internal VIO regulator. The transition from
internal VIO to external VIO is not abrupt. As the back-bias
voltage increases above the VIO setpoint, the load current
8
FIGURE 5. SETPOINT ADJUSTMENT FOR VIO
VIO may be soft-started using the VADJ input. By limiting the
rate of rise of VADJ, the risetime of VIO may be controlled.
Soft-start may be accomplished by placing a capacitor to
ground from VADJ. The capacitor to ground and the resistor
from VPWR determine the RC charging characteristic for the
voltage at VADJ. Since VADJ is pulled low at power-up and
power-down, soft-start always starts from a known state.
The soft-start rate cannot exceed the intrinsic risetime set by
the current limit threshold of the output. As load capacitance
increases, the intrinsic risetime increases. In general,
placing large capacitance values on VIO should be avoided,
particularly if the source voltage applied to VPWR is high.
Having a large load capacitance and high input voltage
results in high power dissipation for a longer duration and
may activate the over-temperature protection before VIO
can be biased externally. Under such conditions, steady
state operation would not be achievable.
If the auxiliary transformer winding used to back-bias VIO
requires a large value of capacitance, it can be isolated from
VIO using a diode as shown in Figure 6.
FN6487.1
August 23, 2007
ISL6720A
.
VIO 11
N/C 10
TRACE1 1
TRACE
+
ISL6720A
VADJ 9
VSW 8
TRACE 3
VSWCOMP 7
ENABLE 6
FIGURE 6. ISOLATING VIO FROM LARGE CAPACITANCES
TRACE 2
VSW
VSW is the switched output and may be turned on and off
using the ENABLE pin (GND = off). The output is adjustable
from 1.5V to 15V, but must always be at least 1.5V lower
than VIO and 5.5V lower than VPWR. VSW uses VIO as its
input source. If the external source applied to VIO is unable
to supply adequate voltage, VPWR will be selected as an
alternate source for VIO (and VSW). VSW is capable of
sourcing up to 50mA continuously, and up to 80mA on a
transient basis.
FIGURE 7. VSW TRANSIENT RESPONSE, 0mA to 50mA
STEP, TRACE1: VSW, TRACE2: VCONT,
TRACE3: VIO
The output voltage is adjusted using the VSWADJ input. The
voltage applied to this pin, multiplied by an internal gain of 7,
sets the output voltage.
VSW = 7 × VSWADJ
V
(EQ. 2)
TRACE 1
With a 220pF capacitor from VSW to VSWCOMP, the load
capacitance on VSW should be 1.0µF nominal, with a range
of 0.47µF to 1.5µF. VSW requires a minimum load of
500µA. These conditions must be met even if the VSW
output is not used.
TRACE 3
VCONT
VCONT, which has a tight tolerance output and can source
25mA, is a continuos output. It remains on during most fault
conditions and precedes VIO and VSW during power-up. It
may be used as reference for other circuitry, or may be used
to power a micro-controller or other similar device.
TRACE 2
VCONT selects VIO as its primary source voltage, but also
uses VPWR if VIO is not present or capable.
VIO must have at least 5V of headroom above VCONT or
VPWR is selected as the source. VCONT is enabled when
VPWR exceeds its UVLO threshold and its operation
precedes the enabling of VIO and VSW by 250μs, nominal.
VCONT requires a minimum 250μA load for stability. It
should be bypassed to GND with a 1µF capacitor and
requires a 1nF compensation capacitor between VCOMP
and VCONT. These conditions must be met even if the
VCONT output is not used.
9
FIGURE 8. VCONT TRANSIENT RESPONSE, 0mA to 25mA
STEP, TRACE1: VSW, TRACE2: VCONT,
TRACE3: VIO
Figure 7 depicts the output deviation on each output when
VSW experiences a 0mA to 50 mA step load. VIO Is
unloaded without back-bias and VCONT has a 250μA
(minimum) load.
Figure 8 depicts the output deviation on each output when
VCONT experiences a 0mA to 25mA step load. VIO Is
unloaded without back-bias and VSW has a 500μA
(minimum) load.
FN6487.1
August 23, 2007
ISL6720A
Over-Temperature Protection
The ISL6720A has a two-stage over-temperature shutdown
mechanism. VIO and VSW shutdown approximately +10°C
lower than VCONT. The hysteresis for both thresholds is
large so that the IC has sufficient time to operate at start-up
loading levels without prematurely re-triggering the over
temperature protection. At rated load on each output, a
+105°C junction temperature, and with VPWR at 80V, the
thermal mass combined with the over-temperature
thresholds allows approximately 10ms of start-up time.
.
VIN
1 VPWR
VPWR
2 VCONT
VPWR provides the source voltage for the IC and load until
VIO is back biased. The IC is disabled (all outputs off) when
UVLO is active.
3 VCOMP
If the application requires high currents or longer start-up
times than the thermal protection allows, the device
dissipation may be reduced by adding a resistor or resistors
in series between the input voltage and VPWR. The
dropping resistance must be selected such that VPWR
remains above the UVLO threshold of VPWR and at least
5.5V greater than VIO under maximum load and minimum
input voltage to maintain regulation.
5 VSWADJ
4 GND
FIGURE 9. ADDING DROPPING RESISTORS TO VPWR
PWB Layout Requirements
Careful layout is essential for satisfactory operation of the
device. In particular, the compensation capacitors must be
connected to VCOMP and VSWCOMP with short trace
lengths.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
10
FN6487.1
August 23, 2007
ISL6720A
Package Outline Drawing
L11.4x4
11 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE
Rev 0, 6/07
2X 2.5
4.00
A
6
PIN 1
INDEX AREA
PIN #1 INDEX AREA
8X 0.50
6
1.0
B
5
1
11X 0 . 45 ± 0 . 1
4.00
(4X)
1.58
0.15
11
6
0.10 M C A B
0.05 M C
TOP VIEW
4 0.25
2.80
BOTTOM VIEW
( 2.80 )
SEE DETAIL "X"
0.10 C
( 11 X 0.65 )
BASE PLANE
0 .9 ± 0.1mm
SIDE VIEW
C
SEATING PLANE
0.08 C
( 3.75 )
( 1.58 )
C
0 . 2 REF
0 . 00 MIN.
0 . 05 MAX.
DETAIL "X"
( 11 X 0 . 25 )
NOTES:
(8X 0.5)
TYPICAL RECOMMENDED LAND PATTERN
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
11
FN6487.1
August 23, 2007
Similar pages