DATASHEET

EL7501
T
UCT
ROD ACEMEN at
P
E
r
T
L
e
E
P
t
L
n
E
e
O
R
OBS ENDED upport C om/tsc
c
.
M
sil
al S
OM
ECData
hnic ww.inter
Sheet
January 1996, Rev B
NO R t o
r Tec
w
u
r
IL o
ac
S
t
n
R
o
E
c
8-INT
1-88
®
100V High Side Driver
Features
The EL7501 provides a low cost
solution to many high side drive
applications. The EL7501 is DC
coupled so there are no start up problems associated with
AC coupled schemes. The EL7501 is driven by user supplied
complementary signals.
• 100V High Side Voltage
FN7289
• Rail to Rail Output
• 1MHz Operation
• 1.0A Peak Current
• Matched Rise and Fall Times
Pinout
• Direct Coupled
• No Start Up Ambiguity
Applications
• Uninterruptible Power Supplies
• DC-DC Converters
• Motor Control
• Power MOSFET Driver
Ordering Information
PART
NUMBER
TEMP. RANGE
PACKAGE
PKG. NO.
EL7501CN
-40°C to +85°C
8-Pin PDIP
MDP0031
EL7501CS
-40°C to +85°C
8-Pin SO
MDP0027
7501 Waveform Example
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
EL7501
Absolute Maximum Ratings (TA = 25°C)
Supply (VDD or LX to R- or R+) . . . . . . . . . . . . . . . . . . . . . . . . .100V
Supply (VDD to LX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V
Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V below GND,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+0.3V above VDD
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2A
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C
Power Dissipation
SOIC . . . . . . . . . . . . . . . . . . . . . . . .570mW
PDIP. . . . . . . . . . . . . . . . . . . . . . . .1050mW
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
TA = 25°C, VDD = 15V, CLOAD = 1000pF, unless otherwise specified.
PARAMETER
Input/Output
Power Supply
DESCRIPTION
VDIFF (Min)
Minimum Differential Input Signal to Switch Output
IDS OFF
Output Leakage
GND < VOUT < VDD
ROH
Pull-up Resistance
ROL
Pull-down Resistance
IPK
Peak Output Current
IDC
Continuous Output Current Source/Sink
IDD
Supply Current into VDD
VDD
Operating Voltage
AC Electrical Specifications
PARAMETER
Switching
Characteristics
TEST CONDITIONS
tR
tF
MIN.
TYP.
MAX.
1.0
-10.0
UNITS
V
0.2
+10.0
µA
IOUT = -100mA
5.0
10.0
Ω
IOUT = +100mA
5.0
10.0
Ω
1.0
A
50.0
mA
4.5
4.0
mA
15.0
V
TA = 25°C, VDD = 15V, CLOAD = 1000pF, unless otherwise specified.
DESCRIPTION
Rise Time
Fall Time
TEST CONDITIONS
MIN.
TYP.
MAX.
CL = 500pF
CL = 1000pF
15.0
20.0
40.0
CL = 500pF
CL = 1000pF
15.0
20.0
40.0
UNITS
ns
ns
tD OFF
Turn Off Delay Time
90.0
140.0
ns
tD ON
Turn On Delay Time
90.0
140.0
ns
2
EL7501
FIGURE 1. EL7501 TEST CIRCUIT
FIGURE 2. EL7501 ALTERNATE DRIVE METHOD
3
EL7501
Typical Performance Curves
Quiescent Supply Current
vs Supply Voltage
Output Rising Edge
Delay Time vs Supply
Voltage and Drive Voltage
4
Average Supply
Current vs Voltage and Frequency
Output Falling Edge
Delay Time vs Supply
Voltage and Drive Voltage
Supply Current vs
DC Offset Voltage and VDD
Delay Time vs
Temperature and
Supply Voltage
EL7501
Typical Performance Curves
(Continued)
Max. Power/
Derating Curves
8-Pin Package
Input Threshold
vs Supply Voltage
Input Current vs
Input Voltage
Enable Threshold vs
Supply Voltage
Peak Drive vs
Supply Voltage
“On” Resistance vs
Supply Voltage
Rise/Fall Time vs
Load and Supply
Rise/Fall Time vs
Temperature
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
5
Similar pages