CA3256 T UCT ROD ACEMEN 47 P E 7 T L OLE REP 00-442-7 OBS ENDED 8 M ns 1 .com COM pplicatio @harris E R NO ntral A entapp Ce : c Call or email Semiconductor January 1999 [ /Title (CA32 56) /Subject (25MH z, BiMO S Analog Video Switch and Amplifier) /Autho r () /Keywords (Harris Semiconductor, 4x1, video crosspoint switch, multiplexer multiplexor, cable driver, 5x1, moni tor output, adjustable gain, 25MHz, BiMOS Analog Video Switch and Amplifier Features Description • 5 Multiplex Video Channels - 1 Independent Channel - 4 Channels with Enable The CA3256 BiMOS analog video switch has five channels of CMOS multiplex switching for general-purpose videosignal control. One of four CMOS channels may be selected in parallel with channel 5. The CMOS switches are inputs to the video amplifier but may be used in bilateral switching between channels 1 to 4 and channel 5. The analog switches of channels 1 to 4 are digitally controlled with logic level conversion and binary decoding to select 1 of 4 channels. The enable function controls channels 1 to 4 but does not affect channel 5. LED output drivers are selected with the channel 1-to-4 switch selection to indicate the ONchannel. Channel 5 may be used as a monitor output for data or signal information on channels 1 to 4. The transmission gate switches shown in the block diagram of the CA3256 are configured in a “T” design to minimize feedthrough. When the switch is off, the shunt or center of the “T” is grounded. • 4 LED Channel Indicator Outputs • Wideband Video Amplifier . . . . . . . . 25MHz Unity Gain • Adjustable Video Amplifier Gain • High Signal-Drive Capability Applications • Video Multiplex Switch • 75Ω Video Amplifier/Line Driver • Video Signal-Level Control • Monitor Switching Control • TV/CATV Audio/Video Switch • Video Signal Adder/Fader Control Part Number Information PART NUMBER TEMP. RANGE (oC) PACKAGE PKG. NO. CA3256E -40 to 85 18 Ld PDIP E18.3 CA3256M -40 to 85 20 Ld SOIC M20.3 The amplifier has high input impedance to minimize the RON transmission gate insertion loss. The amplifier output impedance is typically 5Ω in a complementary symmetry output. The amplifier can directly drive a nominal 75Ω coaxial cable to provide line-to-line video switching. The gain of the amplifier is programmable by different feedback resistor values between pins 8 and 9. Compensation may also be used between these pins for an optimally flat frequency response. An internal regulated 5V bias reference with temperature compensation permits stable direct-coupled output drive and minimizes DC offset during signal switching. Pinouts CA3256 (PDIP) TOP VIEW CA3256 (SOIC) TOP VIEW IN 3 1 18 CONTROL B LED 4 2 17 IN 2 IN 4 3 16 CONTROL A GND 4 15 IN 1 V- 5 14 V+ ENABLE 6 13 IN/OUT 5 CONTROL C 7 12 LED 1 FEEDBACK 8 11 LED 2 AMP OUT 9 10 LED 3 IN3 1 LED4 2 19 IN2 IN4 3 18 CONTROL A GND 4 17 NC V- 5 16 IN1 ENABLE 6 15 V+ CONTROL C 7 14 IN/OUT5 FEEDBACK 8 13 NC AMP OUT 9 12 LED1 LED3 10 11 LED2 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © Harris Corporation 1999 8-1 20 CONTROL B File Number 1769.5 CA3256 Block Diagram 5 4 3 13 3 1 FEED BACK 8 V+ IN/OUT 2 17 1 15 10K BIAS REG 4 - AMPLIFIER OUTPUT 9 + VV+ 14 1K 10K LED DRIVER OUTPUTS TG 12 CHANNEL 1 TG 11 ENABLE 6 BINARY TO 1 OF 4 WITH ENABLE LOGIC LEVEL CONV. CHANNEL 2 TG 10 CHANNEL 3 TG A 16 B 18 2 CHANNEL 4 TG V- 5 C 7 IN TG OUT IN IN OUT SW SW OPEN CONTROL OUT SW CLOSED (DIP PIN OUT) Switch Control Logic CHANNEL NUMBER C A B ENABLE 1 0 0 0 1 2 0 0 1 1 3 0 1 0 1 4 0 1 1 1 5 + (1-4) (Note) 1 Channel 1-4 1 5 1 Channel 5 Only 0 None 0 X X NOTE: For Maximum Video Bandwidth, Use Single Channel Selections 8-2 0 CA3256 Absolute Maximum Ratings Thermal Information DC Supply Voltage Range (V+ to V-) . . . . . . . . . . . . . . . . . . . . . 18V Control Input Voltage Range, All Inputs . . . . . . . . . . . . . . . . V+ to VSignal Input Voltage Range, Channel 1-5 . . . . . . . . . . . . . . . .3VP-P Amplifier Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA DC LED Sink Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA Thermal Resistance (Typical, Note 1) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Maximum Junction Temperature (Die). . . . . . . . . . . . . . . . . . . . 175oC Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications TA = 25oC, V+ = 12V; V- = GND PARAMETER SYMBOL TYPICAL VALUES UNITS 10 to 17 V 20 mA Power Supply Voltage V+ to VPower Supply Current ICC SWITCH AMPLIFIER - 35 dB Programmable Gain, FB Adjustment Range - -0.8 AOL dB Full Power Bandwidth - 10 MHz Unity Gain Bandwidth, 1kΩ, 7pF Compensation - 25 MHz Insertion Loss -0.8 - dB Signal Feedthrough, 5MHz -66 - dB ZIN - 10 kΩ ZOUT - 5 Ω Maximum Input Voltage VI(MAX) 3 2.5 VP-P Maximum Output Voltage, Clipped VO(MAX) - 7 VP-P Reference Bias Output Voltage (V8 - V-) - 5 V Differential Gain - 1 % Differential Phase - 1 Degree -66 - dB LLC Switch Turn On/Off Time Delay - 0.5 µs Maximum LED Sink Current - 30 mA Typical Output Source Current - 16 mA Open Loop Gain Input Impedance Output Impedance AOL Off Isolation, Channel to Channel, ZIN = 75Ω Channel Control Switch A, B, C and EN Threshold (Notes 2, 3) VTH CAUTION: Connect the V- power supply voltage before or during the V+ turn-on. NOTES: 2. Threshold value is referenced to GND. 3. VTH is restricted by the equation, VTH < V+ -1. 8-3 Approximately (V+ - V-)/2 V CA3256 Electrical Specifications TA = 25oC, V+ = 12V, VLED = 12V, V- = GND, Pin 4 = GND, Feedback Switch Closed, VHIGH = 9V, VLOW = 3V (See Figure 1), Unless Otherwise Specified INPUTS CH 1 PARAMETERS CH 2 CH 3 PIN 15 PIN 17 PIN 1 CHANNEL SWITCH CONTROL CH 4 CH 5 A B C PIN 3 PIN 13 PIN 16 PIN 18 PIN 7 ENABLE NOTE 6 TEST PIN 6 PIN# MIN TYP MAX UNITS Supply Current, VLED = 0V 0V 0V 0V 0V 0V 3V 3V 3V 3V 14 10 16 22 mA Dual Supply Current V+ = +7V, V- = -5V 0V 0V 0V 0V 0V 0V 0V 0V 7V 14/5 10 20 26 mA Amplifier Output Voltage, Open Loop VLED = 0V 0V 0V 0V 0V 0V 3V 3V 3V 3V 9 6 8.5 10 V Amplifier Output Voltage, Closed Loop, VLED = 0V 0V 0V 0V 0V 0V 3V 3V 3V 3V 9 4.8 5.1 5.4 V IOUT (MAX) (Source) Open Loop 0V 0V 0V 0V 0V 3V 3V 3V 3V 9 Note 4 - -70 -25 mA IOUT (MAX) (Sink) Open Loop 0V 0V 0V 0V 0V 3V 3V 3V 3V 9 Note 5 10 16 - mA Input Leakage Channel 1-5 3V 3V 3V 3V 3V 3V 3V 3V 3V 1, 3, 15, 17 -15 5 15 nA Channel Control Input A, B, C, Enable Leakage 0V 0V 0V 0V 0V Measure at 3V, 9V each; Enable and Channel Switching Control Inputs 6, 7, 16, 18 -20 10 20 nA LED Off Voltage, VOFF 0V 0V 0V 0V 0V Select Channel 0-5 2, 10, 11, 12 - V LED On Voltage, VON 0V 0V 0V 0V 0V Select Channel 0-5 2, 10, 11, 12 ±100µA Input Each Switch, Channel 1-4 + 5 Switch Resistance, RDS RDS Match Select Channel 1-4 9V - 0.1 0.3 V 0.8 1.1 1.4 kΩ - - 3.6 5 % 9V Calculation: (Max RDS - Min RDS)/Min RDS 11.97 11.99 Amplifier Output Offset, VO , Feedback Switch Closed V+ = +7V, V- = -5V 0V 0V 0V 0V 0V 0V 0V 0V 7V 9 -100 45 100 mV Closed Loop Gain 3V 0V 0V 0V 0V 3V 3V 3V 9V 9 -0.5 -0.1 0.5 dB NOTES: 4. VOUT = +7V. 5. VOUT = +3V. 6. DIP Pinout. 8-4 CA3256 Test Circuits V- V+ +12 V FEEDBACK SWITCH FEEDBACK 14 5 8 VBIAS (V- +5V) BIAS REG 10K 1K AMP OUT 9 + IN 1 15 10K TG-1 OUTPUT AMP VLED 1.1K IN 2 1 12 2 11 3 10 4 2 +12 V TG-2 17 1.1K IN 3 TG-3 1 1.1K IN 4 TG-4 3 IN/OUT 5 LLC ENABLE AND CHAN 1-4 SELECT 1.1K TG-5 13 6 ENABLE 16 A 18 B 7 C 4 GND CONTROL INPUTS (CHANNEL SELECT) FIGURE 1. CA3256 TEST CIRCUIT (DIP PINOUT) Application Information CMOS analog switches are available in a wide variety of forms, and have been known and used for some time. There are a number of advantages to using the CMOS transmission gate as a switch: • • • • • • • • • Ideal Suitability to Series Cascade Arrangements Simple Multiple Parallel Input Switching Arrangements No Bipolar Junctions and, Hence, No Offset Very Low Power Consumption Wide Signal-Swing Capability Fast Multiplexing and Video Switching Wide Bandwidth Low RON Channel Resistance Bidirectional Signal Handling An Integrated Video-Switch Amplifier Commonly, integrated video-switch amplifiers have been fabricated in the bipolar technology using differential amplifiers in a current-switching mode. In this form, two differential pairs are needed for two input-signal sources. The handling of multiple sources is very much more complex. The advantages of the CMOS video-switch amplifier have already been noted. While the bipolar video switch has high output drive and switching speed as advantages, the price is high in voltage offset and current drain. The integrated device solution that is offered here is in the use of the BiMOS technology, where both the CMOS and bipolar processes complement each other to provide CMOS switching with bipolar amplifiers. The BiMOS process allows several CMOS switches to be coupled to a bipolar drive-amplifier in the same process to exploit the best of two technologies. Other advantages are gained when the BiMOS process is used for an IC video-switch amplifier design. The BiMOS process calls for a P-substrate and, therefore, isolated N-epitaxial wells can be built for both N and P channel parts. The boats provide for better isolation of the N and P channels. The N and P wells in a transmission-gate cell can be switched between source and rail; therefore, they have a smaller body effect on both N and P devices, which results in better gain linearity. Where desired, oxide capacitors are available for bipolar amplifier compensation. CA3256 Video-Switch Amplifier The Block Diagram shows the functional diagram of the CA3256, which consists of five MOS channels, each comprising a three-element T-switch. The output of the five switches is made common and fed into the input of a bipolar 8-5 CA3256 selectable for use as a separate input or output in parallel with any on channel, and may be used as a monitor, or for pass-through, signal summing, or parallel distribution. buffer amplifier. The T-switch, together with the input impedance of the buffer, is typically 10kΩ, and has an insertion loss of approximately 0.8dB. The T-switch was designed to handle up to 3VP-P input signal with low distortion. The T-switches of the CA3256 conform to a break-before-make format; hence, shorting to ground is eliminated. In the application, the user has the option to specify V- = -5V for the switch and a ground reference for the amplifier input and output. Alternatively, the CA3256 may be used with a single +12V supply. The logic select for channels 1 through 4 is controlled by the A, B and Inhibit lines with ground to V+ logic switching. The logic threshold is approximately (V+ - V-)/2 referenced to ground. DC coupling may also be used at the output (when V- is returned to a -5V supply). For the circuit of Figure 3, AC coupling is used at the output and input. The switching bias arrangement shown provides for stable bias across each switch when in the off position to minimize transients when the input is switched. The amplifier is programmable for gain and, typically, can provide a gain of 1 into a 75Ω load or a gain of 5 into a 1kΩ load. The maximum output signal swing with linearity is greater than 5VP-P for (V+ to V-) greater than or equal to 12V, while the maximum output current is approximately 20mA. The amplifier has base-current compensation to reduce offset and a temperature compensated 5V zener referenced bias. Other features include LED-selector indicators for channels 1 through 4. The fifth channel is independently Typical Applications V100K V+ -5V RF +7V TO +12V 5 14 8 V- +5V 100K BIAS REG 100K AMPLIFIER TO CABLE OUTPUT 1K 10K - 9 + 10K CHANNEL 1 INPUT 15 OUT 75Ω 75Ω OUTPUT AMP TG-1 LED INDICATOR CHANNEL 1 VLED 12 1 17 TG-2 LED INDICATOR CHANNEL 2 2 OF 5 INPUTS SHOWN 11 2 1 TG-3 LED INDICATOR CHANNEL 3 10 3 TG-4 3 CHANNEL 5 INPUT/ OUTPUT LED INDICATOR CHANNEL 4 LLC ENABLE AND CHAN 1-4 SELECT 2 4 WHERE AMPLIFIER GAIN: 13 R F + 1K AV = 1 + ---------------------- x 0.9 10K TG-5 i.e., FOR AV = 1.8 A ENABLE CHANNEL 1-4 16 6 4.7K 4.7K B 18 SELECT CHANNEL 1-4 RF = 9kΩ C SELECT CHANNEL 7 5 4.7K 4 4.7K GND FIGURE 2. TYPICAL APPLICATION WITH DIRECT-COUPLED OUTPUT AND V- = -5V (DIP PINOUT) 8-6 CA3256 V- V+ +12 TO +18V RF 100K 0.1µF 0.047µF 0.047µF 2.2µF 2.2µF CCOMP 100K 14 5 8 100K V- +5V BIAS REG 75Ω 10K 2.2µF CHANNEL 1 INPUT 220µF OUTPUT AMP TG-1 VOUT 1 9 + 10K 15 VOUT 2 1K 75Ω 75Ω LED INDICATOR CHANNEL 1 17 1 12 2 11 VLED TG-2 LED INDICATOR CHANNEL 2 2 OF 5 INPUTS SHOWN TG-3 1 LED INDICATOR CHANNEL 3 3 TG-4 3 CHANNEL 5 INPUT/ OUTPUT 10 LED INDICATOR CHANNEL 4 LLC ENABLE AND CHAN 1-4 SELECT 2.2µF 4 2 TG-5 13 WHERE AMPLIFIER GAIN: R F + 1K AV = 1 + ---------------------- x 0.9 10K 75Ω ENABLE CHANNEL 1-4 A 16 6 4.7K 4.7K C B 18 SELECT CHANNEL 1-4 4.7K 4 7 SELECT CHANNEL 5 4.7K GND FOR THIS CIRCUIT: V+ = +12V AV = 1.1 BW = 18MHz (SINEWAVE) VOUT = 1VP-P RF = 1K Pulse Performance = 20ns tR for 0V to 2V Pulse. See Figure 4 for frequency response. VIN V+ = +12V, RF = 1kΩ, CCOMP = 6pF. VOUT FIGURE 3. TYPICAL APPLICATION WITH AC-COUPLED INPUT AND OUTPUT, AND V- = GND (DIP PINOUT) 8-7 CA3256 VIN = 200mVP-P, AT LOW FREQUENCY 0dB REF. EQUAL 1.13 x GAIN, TA = 25oC 7pF 0 C COMP 8 -2 RF 1kΩ GAIN (dB) 1kΩ -4 VOUT 9 + -6 220µF VIN TG 75Ω OUTPUT AMPLIFIER -8 -10 0.01 0.1 1 FREQUENCY (MHz) 10 100 FIGURE 4A. CLOSED LOOP RESPONSE WITH COMPENSATION CAPACITOR, CCOMP , AND RF , SEE FIGURE 4B 31 FIGURE 4B. TEST CIRCUIT FOR FIGURE 4A VOUT = 200mVP-P , TA = 25oC 29 NO FEEDBACK 8 GAIN (dB) 27 25 VOUT 9 + V IN 23 TG 220µF 150Ω OUTPUT AMPLIFIER 21 19 0.01 0.1 1 FREQUENCY (MHz) 10 100 FIGURE 4C. OPEN LOOP RESPONSE WITH NO FEEDBACK, SEE FIGURE 4D FIGURE 4D. TEST CIRCUIT FOR FIGURE 4C FIGURE 4. FREQUENCY RESPONSE OF AC COUPLED CIRCUIT OF FIGURE 3 8-8 CA3256 10K (NOTE) V+ VV+ V- = -5V 10K OFF SET ADJ. 15pF 5 14 RF 8 1K V- +5V BIAS REG VOUT = 2VP-P 10K IN 1 9 + 10K TG-1 15 GEN 1K 510Ω OUTPUT AMP V- 75Ω 1 IN 2 75Ω LED TG-2 17 VLED 12 1.2K 75Ω 2 IN 3 1 11 TG-3 LED 1.2K LED 1.2K LED 1.2K 75Ω 3 TG-4 3 IN 4 LLC ENABLE AND CHAN 1-4 SELECT 75Ω IN 5 10 4 TG-5 13 75Ω A 6 ENABLE 2 16 B NOTE: Adjust offset for voltage at pin 9 equal to 0V with no AC signal and one channel “ON”. Dynamic clamping may be accomplished by error current feedback to pin 8. C 18 4 7 GND FIGURE 5. TYPICAL APPLICATION WITH DC-COUPLED INPUT AND OUTPUT, AND OFFSET ADJUST. OUTPUT VOLTAGE IS FIXED BY THE V+ AND V- RANGE. (DIP PINOUT) +1 0 -1 10 2VP-P 10V 0 1µs/DIV. 0.5V/DIV. 0.5V/DIV. FIGURE 6A. GATED OUTPUT FOR V+ = +12V ENABLE = HIGH, CONTROL B = C = LOW, CONTROL A = 10V PULSE. THE BURST OUTPUT IS DELAYED ~ 400ns AT tON, tOFF. 10µs/DIV. 10µs/DIV. FIGURE 6B. STANDARD NTS COLOR BAR FIGURE 6C. UNIFORM STEP SIGNAL WITH 3.58MHz MODULATION FIGURE 6. PERFORMANCE OF CIRCUIT IN FIGURE 5 8-9 CA3256 7pF 2pF AV = 1.1 BW = 18MHz VOUT = 1VP-P 1K 11K 8 8 75Ω 9 AV = 2 BW = 15MHz VOUT = 2VP-P VOUT 9 VOUT 470Ω 75Ω 75Ω NOTE: 470Ω added to increase source drive current. FIGURE 7A. FIGURE 7B. 2pF 8 1K 8 VOUT2 9 VOUT1 9 VOUT 75Ω 75Ω AV = 1.1 BW = 40MHz (1.2X GAIN PEAK AT 25MHz) VOUT = 200mVP-P VOUT1 VOUT2 AV = 1.1 BW = 15MHz VOUT = 200mVP-P FIGURE 7C. 8 NO FEEDBACK 9 AV = 2 BW = 26MHz (UNITY GAIN) VOUT = 400mVP-P FIGURE 7D. AOL = 30 BW = 250kHz VOUT = 200mVP-P 7pF 30K AV = 3.6 BW = 6MHz VOUT = 200mVP-P 8 VOUT VOUT 9 150Ω FIGURE 7E. FIGURE 7F. 100K 6pF 1K - AV = 1.1 BW = 28MHz VOUT = 2VP-P OFFSET ADJ. (SETS DC OUT LEVEL) + 200K 8 8 9 9 AV = 1.1 BW = 28MHz VOUT = 2VP-P 10K 280Ω RS 75Ω ADJ. VDC = 5V 150Ω NOTE: Add RS to reduce high-frequency slewing. FIGURE 7G. FIGURE 7H. FIGURE 7. OTHER TABULATED RESULTS FOR VARIATIONS OF LOAD AND FEEDBACK (V+ = +12V) 8-10 CA3256 Any combination of switch input circuits can be configured with multiple, parallel, line-drive outputs. The video switch amplifier circuit of Figure 8 illustrates how the CA3256 may be configured in pairs to provide an 8-to-1 video switch amplifier using a 3-bit address to select the input. It is also possible to use the fifth channel input to tie signals to a common bus line for distribution from the selected amplifier; however, distributed capacitance loading will result in reduced bandwidth. The 4 plus 1 combination of input-signal switching provides for a wide assortment of video switch circuit configurations. While the BiMOS process does provide some compromises for both the switch and the amplifier, the combined system is capable of the performance needed in most high-quality, switching applications. As an integrated system, many of the problems in PC-board layout are simplified, and there is a reduction in component count. In its simplest form, with +12V and -5V supplies, the CA3256 may be DC connected at the input and output; the LED indicators need not be connected. Under these conditions, the circuit may be as simple as the one in Figure 8. A B C A B C EN1 + VIN1 1 CH 1-4 - VIN2 2 VIN3 3 VIN4 4 CH 5 5 V+ +12V VOUT GND VCA3256 -5V A B C EN2 + - VIN5 1 VIN6 2 CH 5-8 VIN7 3 VIN8 4 NC 5 V+ +12V GND VCA3256 -5V TRUTH TABLE Summary While each video-switch amplifier is designed for a specific application and, to that end, is tailored as far as performance to a given set of specifications, the circuit-designer’s goal is generally the same in every case: to make the best possible switch for the lowest cost. In this respect, the CA3256 IC switch and amplifier discussed provide an excellent choice for a cost-effective high-performance video-switch amplifier, by taking advantage of the complementary features of both high-speed CMOS and bipolar integrated circuits. CH C A B 1 0 0 0 2 0 0 1 3 0 1 0 4 0 1 1 5 1 0 0 6 1 0 1 7 1 1 0 8 1 1 1 FIGURE 8. AN 8-TO-1 VIDEO SWITCH AMPLIFIER USING TWO CA3256 DEVICES 8-11