DATASHEET

HCS165MS
Radiation Hardened Inverting
8-Bit Parallel-Input/Serial Output Shift Register
September 1995
Features
Pinouts
• 3 Micron Radiation Hardened SOS CMOS
16 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T16, LEAD FINISH C
TOP VIEW
• Total Dose 200K RAD (Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/
Bit-Day (Typ)
• Dose Rate Survivability: >1 x
1012
RAD (Si)/s
• Dose Rate Upset >1010 RAD (Si)/s 20ns Pulse
• Latch-Up Free Under Any Conditions
• Fanout (Over Temperature Range)
- Standard Outputs - 10 LSTTL Loads
PL
1
16 VCC
CP
2
15 CE
D4
3
14 D3
D5
4
13 D2
D6
5
12 D1
D7
6
11 D0
Q7
7
10 DS
GND
8
9 Q7
• Military Temperature Range: -55oC to +125oC
• Significant Power Reduction Compared to LSTTL ICs
• DC Operating Voltage Range: 4.5V to 5.5V
16 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP4-F16, LEAD FINISH C
TOP VIEW
• Input Logic Levels
- VIL = 0.3 VCC Max
- VIH = 0.7 VCC Min
• Input Current Levels Ii ≤ 5µA at VOL, VOH
Description
The Intersil HCS165MS is a Radiation Hardened 8-Bit Parallel-In/Serial-Out Shift Register with complementary serial
outputs and an asynchronous parallel load input.
The HCS165MS utilizes advanced CMOS/SOS technology
to achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
VCC
PL
1
16
CP
2
15
CE
D4
3
14
D3
D5
4
13
D2
D6
5
12
D1
D7
6
11
D0
Q7
7
10
DS
GND
8
9
Q7
The HCS165MS is supplied in a 16 lead Ceramic flatpack
(K suffix) or a SBDIP Package (D suffix).
Ordering Information
PART NUMBER
TEMPERATURE RANGE
SCREENING LEVEL
PACKAGE
HCS165DMSR
-55oC to +125oC
Intersil Class S Equivalent
16 Lead SBDIP
HCS165KMSR
-55oC to +125oC
Intersil Class S Equivalent
16 Lead Ceramic Flatpack
HCS165D/Sample
+25oC
Sample
16 Lead SBDIP
HCS165K/Sample
+25oC
Sample
16 Lead Ceramic Flatpack
HCS165HMSR
+25oC
Die
Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
240
Spec Number
File Number
518757
2481.2
HCS165MS
Functional Diagram
D1
D0
D2
D3
D4
D7
D6
D5
CP
CE
DS
CL
DP PL
CL
DP PL
CL
DP PL
CL
DP PL
CL
DP PL
CL
DP PL
CL
DP PL
CL
DP PL
FF
DS Q
FF
DS Q
FF
DS Q
FF
DS Q
FF
DS Q
FF
DS Q
FF
DS Q
FF
DS Q
PL
D7
D7
TRUTH TABLE
INPUTS
OPERATING
MODES
Parallel Load
Serial Shift
Hold “Do Nothing”
Qn REGISTER
OUTPUTS
PL
CE
CP
DS
D0 - D7
Q0
Q1 - Q6
Q7
Q7
L
X
X
X
L
L
L-L
L
H
L
X
X
X
H
H
H-H
H
L
H
L
l
X
L
Q0 - Q5
Q6
Q6
H
L
h
X
H
Q0 - Q5
Q6
Q6
H
H
X
X
Q0
Q1 - Q6
Q7
Q7
X
H = HIGH voltage level
h = HIGH voltage level one setup time prior to the LOW-to-HIGH clock transition
L = LOW voltage level
l = LOW voltage level one setup time prior to the LOW-to-High clock transition
Qn = Lower case letters indicate the state of the referenced output one set-up time prior to the LOW-to-HIGH clock transition.
X = Don’t Care
= LOW-to-HIGH clock transition.
Spec Number
241
518757
Specifications HCS165MS
Absolute Maximum Ratings
Reliability Information
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V
Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V
DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA
DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±25mA
(All Voltage Reference to the VSS Terminal)
Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance
θJA
θJC
SBDIP Package. . . . . . . . . . . . . . . . . . . .
73oC/W
24oC/W
Ceramic Flatpack Package . . . . . . . . . . . 114oC/W
29oC/W
Maximum Package Power Dissipation at +125oC Ambient
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68W
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.44W
If device power exceeds package dissipation capability, provide heat
sinking or derate linearly at the following rate:
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7mW/oC
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 8.8mW/oC
CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent
damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed
under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation..
Operating Conditions
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Input Rise and Fall Times at VCC = 4.5V (TR, TF) . . . . .500ns Max
Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC
Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . 0.0V to 30% of VCC
Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . 70% of VCC to VCC
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Quiescent Current
Output Current
(Sink)
Output Current
(Source)
Output Voltage Low
Output Voltage High
Input Leakage
Current
Noise Immunity
Functional Test
GROUP
A SUBGROUPS
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
-
40
µA
2, 3
+125oC, -55oC
-
750
µA
1
+25oC
4.8
-
mA
2, 3
+125oC, -55oC
4.0
-
mA
1
+25oC
-4.8
-
mA
2, 3
+125oC, -55oC
-4.0
-
mA
VCC = 4.5V, VIH = 3.15V,
IOL = 50µA, VIL = 1.35V
1, 2, 3
+25oC, +125oC, -55oC
-
0.1
V
VCC = 5.5V, VIH = 3.85V,
IOL = 50µA, VIL = 1.65V
1, 2, 3
+25oC, +125oC, -55oC
-
0.1
V
VCC = 4.5V, VIH = 3.15V,
IOH = -50µA, VIL = 1.35V
1, 2, 3
+25oC, +125oC, -55oC
VCC
-0.1
-
V
VCC = 5.5V, VIH = 3.85V,
IOH = -50µA, VIL = 1.65V
1, 2, 3
+25oC, +125oC, -55oC
VCC
-0.1
-
V
VCC = 5.5V, VIN = VCC or
GND
1
+25oC
-
±0.5
µA
2, 3
+125oC, -55oC
-
±5.0
µA
7, 8A, 8B
+25oC, +125oC, -55oC
-
-
-
(NOTE 1)
CONDITIONS
SYMBOL
ICC
IOL
IOH
VOL
VOH
IIN
FN
VCC = 5.5V,
VIN = VCC or GND
VCC = 4.5V, VIH = 4.5V,
VOUT = 0.4V, VIL = 0V
VCC = 4.5V, VIH = 4.5V,
VOUT = VCC -0.4V,
VIL = 0V
VCC = 4.5V,
VIH = 0.70(VCC),
VIL = 0.30(VCC) (Note 2)
LIMITS
NOTES:
1. All voltages reference to device GND.
2. For functional tests VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.
Spec Number
242
518757
Specifications HCS165MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
CP or CE to Q7 or
Q7
PEN to Q7 or Q7
D7 to Q7
D7 to Q7
(NOTES 1, 2)
CONDITIONS
SYMBOL
TPLH
TPHL
GROUP
A SUBGROUPS
TEMPERATURE
MIN
MAX
UNITS
9
+25oC
2
35
ns
10, 11
+125oC, -55oC
2
41
ns
9
+25oC
2
40
ns
10, 11
+125oC, -55oC
2
46
ns
9
+25oC
2
27
ns
10, 11
+125oC, -55oC
2
31
ns
9
+25oC
2
29
ns
10, 11
+125oC, -55oC
2
35
ns
VCC = 4.5V
TPLH
TPHL
VCC = 4.5V
TPLH
TPHL
VCC = 4.5V
TPLH
TPHL
VCC = 4.5V
LIMITS
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Capacitance Power
Dissipation
Input Capacitance
Output Capacitance
Pulse Width Time CP,
PL
Setup Time
DS to CP, CE to CP,
Dn to PL
Hold Time
DS to CP, CE
Hold Time
CE to CP
Recovery Time
PL to CP
Maximum
Frequency
Output Transition Time
SYMBOL
CPD
CIN
COUT
TW
(NOTE 1)
CONDITIONS
VCC = 5.0V, VIH = 5.0V, VIL = 0.0V,
f = 1MHz
VCC = 5.0V, VIH = 5.0V, VIL = 0.0V,
f = 1MHz
VCC = 5.0V, VIH = 5.0V, VIL = 0.0V,
f = 1MHz
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
LIMITS
TEMPERATURE
MIN
MAX
UNITS
+25oC
-
41
pF
-
56
pF
-
10
pF
-
10
pF
-
20
pF
-
20
pF
16
-
ns
24
-
ns
16
-
ns
24
-
ns
7
-
ns
11
-
ns
0
-
ns
0
-
ns
20
-
ns
30
-
ns
30
-
MHz
20
-
MHz
1
15
ns
1
22
ns
+125oC,
+25oC
+125oC,
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
+125oC,
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
VCC = 4.5V, VIH = 4.5V, VIL = 0.0V
-55oC
+25oC
-55oC
+25oC
+125oC,
TTHL
TTLH
-55oC
+25oC
+125oC,
FMAX
-55oC
+25oC
+125oC,
TREC
-55oC
+25oC
+125oC,
TH
-55oC
+25oC
+125oC,
TH
-55oC
+25oC
+125oC,
TSU
-55oC
-55oC
+25oC
+125oC,
-55oC
NOTE:
1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly
tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics.
Spec Number
243
518757
Specifications HCS165MS
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS
200K RAD
LIMITS
PARAMETER
(NOTES 1, 2)
CONDITIONS
SYMBOL
TEMPERATURE
MIN
MAX
UNITS
Quiescent Current
ICC
VCC = 5.5V, VIN = VCC or GND
+25oC
-
0.75
mA
Output Current (Sink)
IOL
VCC = 4.5V, VIN = VCC or GND,
VOUT = 0.4V
+25oC
4.0
-
mA
Output Current
(Source)
IOH
VCC = 4.5V, VIN = VCC or GND,
VOUT = VCC -0.4V
+25oC
-4.0
-
mA
Output Voltage Low
VOL
VCC = 4.5V or 5.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), IOL = 50µA
+25oC
-
0.1
V
Output Voltage High
VOH
VCC = 4.5V or 5.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), IOH = -50µA
+25oC
VCC
-0.1
-
V
Input Leakage Current
IIN
VCC = 5.5V, VIN = VCC or GND
+25oC
-
±5
µA
Noise Immunity
Functional Test
FN
VCC = 4.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), (Note 3)
+25oC
-
-
-
CP or CEN to Q7 or
Q7N
TPLH
TPHL
VCC = 4.5V
+25oC
2
41
ns
PEN to Q7 or Q7N
TPLH
TPHL
VCC = 4.5V
+25oC
2
46
ns
D7 to Q7
TPLH
TPHL
VCC = 4.5V
+25oC
2
31
ns
D7 to Q7N
TPLH
TPHL
VCC = 4.5V
+25oC
2
35
ns
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.
3. For functional tests VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.
TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC)
GROUP B
SUBGROUP
DELTA LIMIT
ICC
5
12µA
IOL/IOH
5
-15% of 0 Hour
PARAMETER
Spec Number
244
518757
Specifications HCS165MS
TABLE 6. APPLICABLE SUBGROUPS
CONFORMANCE GROUPS
METHOD
GROUP A SUBGROUPS
Initial Test (Preburn-In)
100%/5004
1, 7, 9
ICC, IOL/H
Interim Test I (Postburn-In)
100%/5004
1, 7, 9
ICC, IOL/H
Interim Test II (Postburn-In)
100%/5004
1, 7, 9
ICC, IOL/H
PDA
100%/5004
1, 7, 9, Deltas
Interim Test III (Postburn-In)
100%/5004
1, 7, 9
PDA
100%/5004
1, 7, 9, Deltas
Final Test
100%/5004
2, 3, 8A, 8B, 10, 11
Sample/5005
1, 2, 3, 7, 8A, 8B, 9, 10, 11
Subgroup B-5
Sample/5005
1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas
Subgroup B-6
Sample/5005
1, 7, 9
Sample/5005
1, 7, 9
Group A (Note 1)
Group B
Group D
READ AND RECORD
ICC, IOL/H
Subgroups 1, 2, 3, 9, 10, 11,
(Note 2)
NOTES:
1. Alternate Group A testing in accordance with method 5005 of MIL-STD-883 may be exercised.
2. Table 5 parameters only.
TABLE 7. TOTAL DOSE IRRADIATION
CONFORMANCE
GROUPS
TEST
READ AND RECORD
METHOD
PRE RAD
POST RAD
PRE RAD
POST RAD
5005
1, 7, 9
Table 4
1,9
Table 4 (Note 1)
Group E Subgroup 2
NOTE:
1. Except FN test which will be performed 100% Go/No-Go.
TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS
OSCILLATOR
OPEN
GROUND
1/2 VCC = 3V ± 0.5V
VCC = 6V ± 0.5V
50kHz
25kHz
-
16
-
-
-
1 - 6, 10 - 16
-
-
7, 9
1, 16
2
10
STATIC BURN-IN I TEST CONNECTIONS (Note 1)
7, 9
1 - 6, 8, 10 - 15
STATIC BURN-IN II TEST CONNECTIONS (Note 1)
7, 9
8
DYNAMIC BURN-IN TEST CONNECTIONS (Note 2)
-
3 - 6, 8, 11 - 15
NOTES:
1. Each pin except VCC and GND will have a resistor of 10kΩ ± 5% for static burn-in
2. Each pin except VCC and GND will have a resistor of 1kΩ ± 5% for dynamic burn-in
TABLE 9. IRRADIATION TEST CONNECTIONS
OPEN
GROUND
VCC = 5V ± 0.5V
7, 9
8
1 - 6, 10 - 16
NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing.
Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures.
Spec Number
245
518757
HCS165MS
Intersil Space Level Product Flow - ‘MS’
Wafer Lot Acceptance (All Lots) Method 5007
(Includes SEM)
100% Interim Electrical Test 1 (T1)
GAMMA Radiation Verification (Each Wafer) Method 1019,
4 Samples/Wafer, 0 Rejects
100% Static Burn-In 2, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Nondestructive Bond Pull, Method 2023
100% Interim Electrical Test 2 (T2)
Sample - Wire Bond Pull Monitor, Method 2011
100% Delta Calculation (T0-T2)
Sample - Die Shear Monitor, Method 2019 or 2027
100% PDA 1, Method 5004 (Notes 1and 2)
100% Internal Visual Inspection, Method 2010, Condition A
100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or
Equivalent, Method 1015
100% Delta Calculation (T0-T1)
100% Temperature Cycle, Method 1010, Condition C,
10 Cycles
100% Interim Electrical Test 3 (T3)
100% Constant Acceleration, Method 2001, Condition per
Method 5004
100% Delta Calculation (T0-T3)
100% PDA 2, Method 5004 (Note 2)
100% PIND, Method 2020, Condition A
100% Final Electrical Test
100% External Visual
100% Fine/Gross Leak, Method 1014
100% Serialization
100% Radiographic, Method 2012 (Note 3)
100% Initial Electrical Test (T0)
100% Static Burn-In 1, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% External Visual, Method 2009
Sample - Group A, Method 5005 (Note 4)
100% Data Package Generation (Note 5)
NOTES:
1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1.
2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the
failures from subgroup 7.
3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004.
4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005.
5. Data Package Contents:
• Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number,
Quantity).
• Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage.
• GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test
equipment, etc. Radiation Read and Record data on file at Intersil.
• X-Ray report and film. Includes penetrometer measurements.
• Screening, Electrical, and Group A attributes (Screening attributes begin after package seal).
• Lot Serial Number Sheet (Good units serial number and lot number).
• Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test.
• The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed
by an authorized Quality Representative.
Spec Number
246
518757
HCS165MS
AC Load Circuit
AC Timing Diagram
DUT
TEST
POINT
VIH
INPUT
VS
CL
RL
VIL
TPLH
TPHL
VOH
CL = 50pF
VS
RL = 500Ω
OUTPUT
VOL
VOH
TTLH
TTHL
80%
VOL
20%
80%
20%
OUTPUT
AC VOLTAGE LEVELS
PARAMETER
HCS
UNITS
VCC
4.50
V
VIH
4.50
V
VS
2.25
V
VIL
0
V
GND
0
V
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Spec Number
247
518757
HCS165MS
Die Characteristics
DIE DIMENSIONS:
95 x 94 mils
METALLIZATION:
Type: AlSi
Metal Thickness: 11kÅ ± 1kÅ
GLASSIVATION:
Type: SiO2
Thickness: 13kÅ ± 2.6kÅ
WORST CASE CURRENT DENSITY:
< 2.0 x 105A/cm2
BOND PAD SIZE:
100µm x 100µm
4 x 4 mils
Metallization Mask Layout
HCS165MS
CP
(2)
PL
(1)
VCC
(16)
CE
(15)
D3
(14)
D4 (3)
(13) D2
D5 (4)
(12) D1
D6 (5)
(11) D0
(6)
D7
(7)
Q7
(8)
GND
(9)
Q7
(10)
DS
NOTE: The die diagram is a generic plot from a similar HCS device. It is intended to indicate approximate die size and bond pad location.
The mask series for the HCS165 is TA14385A.
Spec Number
248
518757
Similar pages