TOMC www.vishay.com Vishay Dale Thin Film Molded, 50 mil Pitch, Dual-In-Line Thin Film Resistor, Surface Mount Network FEATURES Actual Size Vishay Dale Thin Film offers standard circuits in 16 pins in a medium body molded surface mount package. The networks are available over a resistance range of 100 to 100 k. The network features tight ratio tolerances and close TCR tracking. In addition to the standards shown, custom circuits are available upon request. • 0.090" (2.29 mm) maximum seated height • Rugged, molded case construction (0.22" wide) • Highly stable thin film ratio stability (R ± 0.015 % at 70 °C for 2000 h) • Low temperature coefficient, ± 25 ppm/°C (- 55 °C to + 125 °C) • Wide resistance range 100 to 100 k • Isolated/bussed circuits • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Note * Lead (Pb)-containing terminations are not RoHS-compliant. Exemptions may apply. TYPICAL PERFORMANCE ABSOLUTE TRACKING 25 5 ABSOLUTE RATIO 0.1 0.025 TCR TOL. SCHEMATIC The 01 circuit provides 15 nominally equal resistors, each connected between a common lead (16) and a discrete PC board pin. Ref. The 03 circuit provides a choice of 8 nominally equal resistors with each resistor isolated from all others and wired directly across. Ref. PIN 1 PIN 1 TOMC-1603 03 circuit TOMC-1601 01 circuit STANDARD ELECTRICAL SPECIFICATIONS TEST Material Pin/Lead Number Resistance Range TCR: Absolute TCR: Tracking Tolerance: Absolute Tolerance: Ratio Power Rating: Resistor Power Rating: Package Stability: Absolute Stability: Ratio Voltage Coefficient Working Voltage Operating Temperature Range Storage Temperature Range Noise Thermal EMF Shelf Life Stability: Absolute Shelf Life Stability: Ratio Revision: 08-Jan-13 SPECIFICATIONS Passivated nichrome 16 100 to 100 kper resistor ± 25 ppm/°C ± 5 ppm/°C ± 0.1 % to 1 % ± 0.025 % to 0.5 % 50 mW = PIN 16 common 100 mW = isolated 750 mW R ± 0.05 % R ± 0.015 % 0.1 ppm/V 100 V max. not to exceed P x R - 55 °C to + 125 °C - 55 °C to + 150 °C < - 30 dB 0.08 μV/°C R ± 0.01 % R ± 0.002 % CONDITIONS - 55 °C to + 125 °C - 55 °C to + 125 °C + 25 °C + 25 °C Maximum at + 70 °C Maximum at + 70 °C 2000 h at + 70 °C 2000 h at + 70 °C 1 year at + 25 °C 1 year at + 25 °C Document Number: 60008 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TOMC www.vishay.com Vishay Dale Thin Film DIMENSIONS AND IMPRINTING in inches and millimeters DIMENSION A B C D E F G H J K L M N P Q R S A G D E Typical H Part Number Date Code Vishay Symbol Lead #1 Indicator Centered 7° F Maximum J Marking 7° Area TOMC-XX B Centered Maximum, Marking Area M K L ± 0.015 (1.27) Q P R C S 7° N 7° MECHANICAL SPECIFICATIONS Passivated nichrome Substrate Material Silicon Sn85 Tin Lead and Lead (Pb)-free Finish Plated Single Resistor 0.085 W 0.045 W 100 % matte tin Tin Lead Option 0.48 W Power Copper alloy Lead (Pb)-free Option TOMC-1601, TOMC-1603 0.75 W 0.65 W Molded epoxy Terminals MILLIMETERS 8.89 10.16 11.176 1.27 0.457 4.06 2.03 0.914 5.59 6.20 7.52 1.14 0.076 1.27 0.203 2.16 0.076 DERATING CURVE Resistive Element Body INCHES 0.350 0.400 0.440 0.050 0.018 0.160 0.08 0.036 0.22 0.244 0.30 0.045 0.003 0.005 0.008 0.085 0.003 0.05 W - 50 °C - 25 °C + 70 °C + 125 °C + 150 °C GLOBAL PART NUMBER INFORMATION New Global Part Numbering: TOMC16031002BUF T T O M C 1 6 0 3 1 0 0 2 B U F O M C T 1 6 0 1 1 0 0 3 Z T 1 GLOBAL MODEL (4 or 5 digits) TOMC (Tin lead) PINS SCHEMATIC RESISTANCE 16 01 = 15 bussed equal resistors First 3 digits are significant figures and the last digit specifies the number of zeros to follow. 03 = 7 or 8 isolated equal resistors TOMCT (Lead (Pb)-free) (e3) Example: 1002 = 10K 1003 = 100K TOLERANCE AND RATIO TOLERANCE Abs. Tol. Ratio A = 0.1 % (1) B = 0.1 % C = 0.25 % D = 0.5 % F=1% Z = 0.1 % (2) 0.05 % 0.1 % 0.1 % 0.1 % 0.5 % 0.025 % PACKAGING TAPE AND REEL T0 = 100 min., 100 mult T1 = 1000 min., 1000 mult (3) T3 = 300 min., 300 mult T5 = 500 min., 500 mult TF = Full reel 2000 TS = 100 min., 1 mult UF = TUBED Historical Part Number example: TOMC16011002Z (for reference purposes only) TOMC 16 01 1002 Z SERIES NUMBER OF LEADS SCHEMATIC RESISTANCE TOLERANCE AND RATIO TOLERANCE Notes (1) Tolerance available 250 and up (2) Tolerance available 1K and up (3) Preferred packaging code Revision: 08-Jan-13 Document Number: 60008 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000