Data Sheet

PCA9518
Expandable 5-channel I2C-bus hub
Rev. 05 — 2 December 2008
Product data sheet
1. General description
The PCA9518 is a BiCMOS integrated circuit intended for application in I2C-bus and
SMBus systems.
While retaining all the operating modes and features of the I2C-bus system, it permits
extension of the I2C-bus by buffering both the data (SDA) and the clock (SCL) lines, thus
enabling virtually an unlimited number of buses of 400 pF.
The I2C-bus capacitance limit of 400 pF restricts the number of devices and bus length.
Using the PCA9518 enables the system designer to divide the bus into an unlimited
number of segments off of a hub where any segment to segment transition sees only one
repeater delay and is multiple master capable on each segment.
Using multiple PCA9518 parts, any width hub (in multiples of five)1 can be implemented
using the expansion pins.
The PCA9518 is a wider voltage range (2.3 V to 3.6 V) version of the PCA9518 and also
improves partial power-down performance, keeping I2C-bus I/O pins in high-impedance
state when VDD is below 2.0 V.
A PCA9518 cluster cannot be put in series with a PCA9515/16 or with another
PCA9518 cluster. Multiple PCA9518 devices can be grouped with other PCA9518
devices into any size cluster thanks to the EXPxxxn pins that allow the I2C-bus signals to
be sent/received from/to one PCA9518 to/from another PCA9518 within the cluster. Since
there is no direction pin, slightly different ‘legal’ low voltage levels are used to avoid
lock-up conditions between the input and the output of individual repeaters in the cluster.
A ‘regular LOW’ applied at the input of any of the PCA9518 devices will then be
propagated as a ‘buffered LOW’ with a slightly higher value to all enabled outputs in the
PCA9518 cluster. When this ‘buffered LOW’ is applied to a PCA9515 and PCA9516 or
separate PCA9518 cluster (not connected via the EXPxxxn pins) in series, the second
PCA9515 and PCA9516 or PCA9518 cluster will not recognize it as a ‘regular LOW’ and
will not propagate it as a ‘buffered LOW’ again. The PCA9510/9511/9513/9514 and
PCA9512 cannot be used in series with the PCA9515 and PCA9516 or PCA9518, but can
be used in series with themselves since they use shifting instead of static offsets to avoid
lock-up conditions.
1.
Only four ports per device are available if individual Enable is required.
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
2. Features
n
n
n
n
n
n
n
n
n
n
n
n
Expandable 5 channel, bidirectional buffer
I2C-bus and SMBus compatible
Active HIGH individual repeater enable inputs
Open-drain input/outputs
Lock-up free operation
Supports arbitration and clock stretching across the repeater
Accommodates Standard-mode and Fast-mode I2C-bus devices and multiple masters
Powered-off high-impedance I2C-bus pins
Operating supply voltage range of 3.0 V to 3.6 V
5 V tolerant I2C-bus and enable pins
0 Hz to 400 kHz clock frequency2
ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per
JESD22-A115, and 1000 V CDM per JESD22-C101
n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
n Package offerings: SO20 and TSSOP20
3. Ordering information
Table 1.
Ordering information
Tamb = −40 °C to +85 °C
Type number
Topside mark Package
Name
Description
Version
PCA9518D
PCA9518D
SO20
plastic small outline package; 20 leads; body width 7.5 mm
SOT163-1
PCA9518PW
PCA9518
TSSOP20
plastic thin shrink small outline package; 20 leads;
body width 4.4 mm
SOT360-1
2.
The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
2 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
4. Block diagram
VCC
EXPSCL1
EXPSCL2
PCA9518
BUFFER
SCL0
BUFFER
SCL1
BUFFER
SCL4
BUFFER
SCL3
BUFFER
SDA4
BUFFER
SDA3
HUB
LOGIC
BUFFER
SCL2
EXPSDA1
EXPSDA2
BUFFER
SDA0
BUFFER
SDA1
HUB
LOGIC
BUFFER
SDA2
EN1
EN4
EN2
EN3
002aae325
GND
Fig 1.
Block diagram of PCA9518
A more detailed view of Figure 1 buffer is shown in Figure 2.
data
to output
in
inc
enable
Fig 2.
002aac531
Buffer detail
The output pull-down voltage of each internal buffer is set for approximately 0.5 V, while
the input threshold of each internal buffer is set about 0.07 V lower, when the output is
internally driven LOW. This prevents a lock-up condition from occurring.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
3 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
5. Pinning information
5.1 Pinning
EXPSCL1
1
20 VCC
2
20 VCC
19 EXPSDA2
EXPSCL1 1
EXPSCL2
EXPSCL2 2
19 EXPSDA2
SCL0
3
18 EXPSDA1
SCL0 3
18 EXPSDA1
SDA0
4
17 EN4
SDA0 4
17 EN4
SCL1
5
16 SDA4
SCL1 5
SDA1
6
15 SCL4
SDA1 6
EN1
7
14 EN3
SCL2
8
13 SDA3
SCL2 8
13 SDA3
SDA2
9
12 SCL3
SDA2 9
12 SCL3
PCA9518D
GND 10
11 EN2
EN1 7
Pin configuration for SO20
16 SDA4
15 SCL4
14 EN3
GND 10
002aac739
Fig 3.
PCA9518PW
11 EN2
002aac740
Fig 4.
Pin configuration for TSSOP20
5.2 Pin description
Table 2.
Pin description
Symbol
Pin
Description
EXPSCL1
1
expandable serial clock pin 1
EXPSCL2
2
expandable serial clock pin 2
SCL0
3
serial clock bus 0
SDA0
4
serial data bus 0
SCL1
5
serial clock bus 1
SDA1
6
serial data bus 1
EN1
7
active HIGH bus 1 enable input
SCL2
8
serial clock bus 2
SDA2
9
serial data bus 2
GND
10
supply ground
EN2
11
active HIGH bus 2 enable input
SCL3
12
serial clock bus 3
SDA3
13
serial data bus 3
EN3
14
active HIGH bus 3 enable input
SCL4
15
serial clock bus 4
SDA4
16
serial data bus 4
EN4
17
active HIGH bus 4 enable input
EXPSDA1
18
expandable serial data pin 1
EXPSDA2
19
expandable serial data pin 2
VCC
20
supply voltage
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
4 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
6. Functional description
The PCA9518 BiCMOS integrated circuit is a five-way hub repeater, which enables
I2C-bus and similar bus systems to be expanded in increments of five with only one
repeater delay and no functional degradation of system performance.
The PCA9518 BiCMOS integrated circuit contains five multi-directional, open-drain buffers
specifically designed to support the standard low-level contention arbitration of the
I2C-bus. Except during arbitration or clock stretching, the PCA9518 acts like a pair of
non-inverting, open-drain buffers, one for SDA and one for SCL.
Refer to Figure 1 “Block diagram of PCA9518”.
6.1 Enable
The enable pins EN1 through EN4 are active HIGH and have internal pull-up resistors.
Each enable pin ENn controls its associated SDAn and SCLn ports. When LOW, the ENn
pin blocks the inputs from SDAn and SCLn, as well as disabling the output drivers on the
SDAn and SCLn pins. The enable pins should only change state when both the global bus
and the local port are in an idle state to prevent system failures.
The active HIGH enable pins allow the use of open-drain drivers which can be wire-ORed
to create a distributed enable where either centralized control signal (master) or spoke
signal (sub-master) can enable the channel when it is idle.
Unused channels must have pull-up resistors unless their enable pin (ENn) is always
LOW. Port 0 must always have pull-up resistors since it is always present in the bus and
cannot be disabled.
6.2 Expansion
The PCA9518 includes 4 open-drain I/O pins used for expansion. Two expansion pins,
EXPSDA1 and EXPSDA2 are used to communicate the internal state of the serial data
within each hub to the other hubs. The EXPSDA1 pins of all hubs are connected together
to form an open-drain bus. Similarly, all EXPSDA2 pins, EXPSCL1 pins, and all EXPSCL2
pins are connected together forming a 4-wire bus between hubs.
When it is necessary to be able to deselect every port, each expansion device only
contributes 4 ports which can be enabled or disables because the fifth does not have an
enable pin.
Pull-up resistors are required on the EXPxxxn3 pins even if only one PCA9518 is used.
6.3 I2C-bus systems
As with the standard I2C-bus system, pull-up resistors are required to provide the logic
HIGH levels on the buffered bus. (Standard open-collector or open-drain configuration of
the I2C-bus). The size of these pull-up resistors depends on the system, but each side of
the repeater must have a pull-up resistor. This part is designed to work with
Standard-mode (0 Hz to 100 kHz) and Fast-mode (0 Hz to 400 kHz) I2C-bus devices in
addition to SMBus devices. Standard-mode I2C-bus devices only specify 3 mA output
drive; this limits the termination current to 3 mA in a generic I2C-bus system where
3.
‘xxxn’ is SDA1, SDA2, SCL1 or SCL2. ‘xxx’ is SDA or SCL.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
5 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
Standard-mode devices and multiple masters are possible. Please see application note
AN255, I2C/SMBus Repeaters, Hubs and Expanders for additional information on sizing
resistors.
7. Application design-in information
A typical application is shown in Figure 5. In this example, the system master is running
on a 3.3 V I2C-bus while the slaves are connected to a 3.3 V or 5 V bus. All buses run at
100 kHz unless slave 3, slave 4 and slave 5 are isolated from the bus. Then the master
bus and slave 1, slave 2 and slave 6 can run at 400 kHz.
Any segment of the hub can talk to any other segment of the hub. Bus masters and slaves
can be located on any segment with 400 pF load allowed on each segment.
The PCA9518 is 5 V tolerant, so it does not require any additional circuitry to translate
between the different bus voltages.
When one port of the PCA9518 is pulled LOW by a device on the I2C-bus, a CMOS
hysteresis type input detects the falling edge and drives the EXPxxx1 line LOW, when the
EXPxxx1 voltage is less than 0.5VCC, the other ports are pulled down to the VOL of the
PCA9518 which is typically 0.5 V.
In order to illustrate what would be seen in a typical application, refer to Figure 6. If the
bus master in Figure 5 were to write to the slave through the PCA9518, we would see the
waveform shown in Figure 6. This looks like a normal I2C-bus transmission except for the
small foot preceding each clock LOW-to-HIGH transition and proceeding each data
LOW-to-HIGH transition for the master. The foot height is the difference between the LOW
level driven by the master and the higher voltage LOW level driven by the PCA9518
repeater. Its width corresponds to an effective clock stretching coming from the PCA9518
that delays the rising edge of the clock. That same magnitude of delay is seen on the
rising edge of the data. The foot on the rising edge of the data is extended through the 9th
clock pulse as the PCA9518 repeats the acknowledge from the slave to the master. The
clock of the slave looks normal except the VOL is the ~0.5 V level generated by the
PCA9518. The SDA at the slave has a particularly interesting shape during the 9th clock
cycle where the slave pulls the line below the value driven by the PCA9518 during the
acknowledge and then returns to the PCA9518 level creating a foot before it completes
the LOW-to-HIGH transition. SDA lines other than the one with the master and the one
with the slave have a uniform LOW level driven by the PCA9518 repeater.
The other four waveforms are the expansion bus signals and are included primarily for
timing reference points. All timing on the expansion bus is with respect to 0.5VCC.
EXPSDA1 is the expansion bus that is driven LOW whenever any SDA pin falls below
0.3VCC. EXPSDA2 is the expansion bus that is driven LOW whenever any pin is ≤0.4 V.
EXPSCL1 is the expansion bus that is driven LOW whenever any SCL pin falls below
0.3VCC. EXPSCL2 is the expansion bus that is driven LOW whenever any SCL pin is
≤0.4 V. The EXPSDA2 returns HIGH after the SDA pin that was the last one being held
below 0.4 V by an external driver starts to rise. The last SDA to rise above 0.4 V is held
down by the PCA9518 to ~0.5 V until after the delay of the circuit which determines that it
was the last to rise, then it is allowed to rise above the ~0.5 V level driven by the
PCA9518. Considering the bus 0 SDA to be the last one to go above 0.4 V, then the
EXPSDA1 returns to HIGH after the EXPSDA2 is HIGH and either the bus 0 SDA rise time
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
6 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
is 1 µs or, when the bus 0 SDA reaches 0.7VCC, whichever occurs first. After both
EXPSDA2 and EXPSDA1 are HIGH the rest of the SDA lines are allowed to rise. The
same description applies for the EXPSCL1, EXPSCL2, and SCL pins.
3.3 V
5V
5V
VCC
SDA
SDA1
SCL
SUBSYSTEM 5
100 kHz
SCL1
VCC
EXPSDA1
EXPSDA1
EXPSDA2
EXPSDA2
EXPSCL1
EXPSCL1
EXPSCL2
EXPSCL2
SDA1
SDA
SCL1
SCL
SUBSYSTEM 1
400 kHz
3.3 V
3.3 V
SDA
SDA2
SDA2
SDA
SCL
SUBSYSTEM 6
400 kHz
SCL2
SCL2
SCL
SUBSYSTEM 2
400 kHz
3.3 V
or 5 V
SDA0
SDA
SDA0
SCL0
SCL
SCL0
5V
PCA9518
PCA9518
DEVICE 2
DEVICE 1
BUS
MASTER
SDA3
SCL3
disabled;
not connected
400 kHz
3.3 V
or 5 V
EN1
EN1
EN2
EN2
EN3
EN3
EN4
EN4
SDA3
SDA
SCL3
SCL
SUBSYSTEM 3
100 kHz
3.3 V
SDA4
SDA4
SDA
SCL4
SCL4
SCL
SUBSYSTEM 4
100 kHz
GND
GND
002aae326
Only two of the five channels on the PCA9518 Device 2 are being used. EN3 and EN4 are connected to GND to disable
channels 3 and 4 and/or SDA3/SCL3 and SDA4/SCL4 are pulled up to VCC. SDA0 and SCL0 can be used as a normal I2C-bus
port, but if unused then it must be pulled up to VCC since there is no enable pin.
The pull-ups shown on Device 2 channels 3 and 4 are not required if their enable pins (ENn) are permanently held LOW.
Fig 5.
Typical application: multiple expandable 5-channel I2C-bus hubs
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
7 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
9th clock cycle
VOL of master
VOL of PCA9518
9th clock cycle
SCL of
master
Bus 0
tstretch
SDA of
master
tPHL1
EXPSDA1
tPLH1
tPHL2
tPLH2, tPLH1
tPLH2
EXPSDA2
expansion
bus
EXPSCL1
EXPSCL2
SCL of
slave
Bus 1
VOL of slave
VOL of PCA9518
SDA of
slave
tPHL
tPLH
Bus n
with n > 1
002aae327
Fig 6.
Bus waveforms
It is important to note that any arbitration or clock stretching events on Bus 1 require that
the VOL of the devices on Bus 1 be 70 mV below the VOL of the PCA9518 (see VOL−VILc in
Section 9 “Static characteristics”) to be recognized by the PCA9518 and then transmitted
to Bus 0.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
8 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
8. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
Max
Unit
VCC to GND
[1]
−0.5
+7
V
SCL or SDA
[1]
−0.5
+7
V
-
50
mA
VCC
supply voltage
VI2C-bus
I2C-bus
II
input current
Ptot
total power dissipation
-
300
mW
Tstg
storage temperature
−55
+125
°C
Tamb
ambient temperature
−40
+85
°C
[1]
voltage
any pin
operating
Voltages with respect to pin GND.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
9 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
9. Static characteristics
Table 4.
Static characteristics
VCC = 3.0 V to 3.6 V; GND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
3.0
3.3
3.6
V
-
7.5
10
mA
-
9
11
mA
-
9
11
mA
Supplies
VCC
supply voltage
ICCH
HIGH-level supply current
both channels HIGH
VCC = 3.6 V;
SDAn = SCLn = VCC
ICCL
LOW-level supply current
both channels LOW
VCC = 3.6 V;
one SDA and one SCL = GND;
other SDA and SCL open
ICCLc
contention LOW-level supply
current
VDD = 3.6 V; SDAn = SCLn = VSS
Input SCL; input/output SDA
HIGH-level input voltage
0.7VCC
-
5.5
V
SCL, SDA
[1]
−0.5
-
+0.3VCC
V
VILc
contention LOW-level input voltage SCL, SDA
[2]
−0.5
-
+0.4
V
VIK
input clamping voltage
II = −18 mA
-
-
−1.2
V
ILI
input leakage current
VI = 3.6 V
-
-
±1
µA
IIL
LOW-level input current
SCL, SDA; VI = 0.2 V
-
-
20
µA
0.47
0.52
0.6
V
VIH
LOW-level input voltage
VIL
SCL, SDA
SCL, SDA; IOL = 0
mA[3]
VOL
LOW-level output voltage
or 6 mA
VOL−VILc
difference between LOW-level
guaranteed by design
output and LOW-level input voltage
contention
-
-
70
mV
Ci
input capacitance
-
6
8
pF
VI = 3 V or 0 V
Enable 1 to Enable 4 (EN1 to EN4)
VIL
LOW-level input voltage
−0.5
-
+0.8
V
VIH
HIGH-level input voltage
2.0
-
5.5
V
IIL
LOW-level input current
-
10
30
µA
ILI
input leakage current
−1
-
+1
µA
Ci
input capacitance
-
3
7
pF
V
VI = 0.2 V; EN1 to EN4
VI = 3.0 V or 0 V
Expansion pins (EXPSCL1, EXPSCL2, EXPSDA1, EXPSDA2)
VIH
HIGH-level input voltage
EXPxxxn
0.55VCC -
5.5
VIL
LOW-level input voltage
EXPxxxn
−0.5
-
+0.45VCC V
IIL
LOW-level input current
EXPxxxn; VI = 0.2 V
-
-
5
µA
VOL
LOW-level output voltage
EXPxxxn; IOL = 12 mA
-
-
0.5
V
Ci
input capacitance
VI = 3.0 V or 0 V
-
6
8
pF
[1]
VIL specification is for the first LOW level seen by the SDAn/SCLn lines.
[2]
VILc is for the second and subsequent LOW levels seen by the SDAn/SCLn lines.
[3]
Test performed with IOL = 10 µA.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
10 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
10. Dynamic characteristics
Table 5.
Dynamic characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
105
202
389
ns
110
259
265
ns
tPHL
HIGH to LOW propagation delay
SDA to SDAn, or
SCL to SCLn; Figure 7
[1][2]
tPLH
LOW to HIGH propagation delay
SDA to SDAn, or
SCL to SCLn; Figure 7
[1][3]
tPHL1
HIGH to LOW propagation delay 1
EXPSDA1 to SDA, or
EXPSCL1 to SCL; Figure 7
109
193
327
ns
tPLH1
LOW to HIGH propagation delay 1
EXPSDA1 to SDA, or
EXPSCL1 to SCL; Figure 7
130
153
179
ns
tPLH2
LOW to HIGH propagation delay 2
EXPSDA2 to SDA, or
EXPSCL2 to SCL; Figure 7
160
234
279
ns
tTHL
HIGH to LOW output transition time
SDA, SCL; Figure 7
58
110
187
ns
tTLH
LOW to HIGH output transition time
SDA, SCL; Figure 7
-
0.85 RC
-
ns
tsu
set-up time
enable to START condition
300
-
-
ns
th
hold time
enable after STOP condition
300
-
-
ns
[1]
The SDA and SCL propagation delays are dominated by rise times or fall times. The fall times are mostly internally controlled and are
only sensitive to load capacitance. The rise times are RC time constant controlled and therefore a specific numerical value can only be
given for fixed RC time constants.
[2]
The SDA HIGH to LOW propagation delay includes the fall time from VCC to 0.5VCC of the EXPSDA1 or EXPSCL1 pins and the SDA or
SCL fall time from the quiescent HIGH (usually VCC) to below 0.3VCC. The SDA and SCL outputs have edge rate control circuits
included which make the fall time almost independent of load capacitance.
[3]
The SDA or SCL LOW to HIGH propagation delay includes the rise time constant from the quiescent LOW to 0.5VCC for the EXPSDA1
or EXPSCL2, the rise time constant for the quiescent LOW to 0.5VCC for the EXPSDA1 or EXPSCL1, and the rise time constant from
the quiescent external driven LOW to 0.7VCC for the SDA or SCL output. All of these rise times are RC time constants determined by the
external resistance and total capacitance for the various nodes.
tTHL
input SDA or SCL
tTLH
0.7VCC
0.7VCC
0.3VCC
0.4 V
tPHL
0.3VCC
0.4 V
effective
stretch
tPHL1
EXPSDA1 or EXPSCL1
0.5VCC
0.5VCC
tPHL2
tPLH2
EXPSDA2 or EXPSCL2
0.5VCC
0.5VCC
tPLH
tPLH1
tPHL1
tPLH2
tTHL
tTLH
0.7VCC
output SDA or SCL
0.52 V
Fig 7.
0.3VCC
0.3VCC
002aae328
AC waveforms
PCA9518_5
Product data sheet
0.7VCC
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
11 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
11. Test information
VCC
VCC
RL
PULSE
GENERATOR
VI
VO
DUT
CL
RT
002aad479
RL = load resistor; 1.1 kΩ for I2C-bus, and 500 Ω for EXPxxxn.
CL = load capacitance includes jig and probe capacitance; 100 pF for I2C-bus, and 100 pF for
EXPxxxn.
RT = termination resistance should be equal to Zo of the pulse generators.
Fig 8.
Test circuit for open-drain outputs
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
12 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
12. Package outline
SO20: plastic small outline package; 20 leads; body width 7.5 mm
SOT163-1
D
E
A
X
c
HE
y
v M A
Z
20
11
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
10
1
e
bp
detail X
w M
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
mm
2.65
0.3
0.1
2.45
2.25
0.25
0.49
0.36
0.32
0.23
13.0
12.6
7.6
7.4
1.27
10.65
10.00
1.4
1.1
0.4
1.1
1.0
0.25
0.25
0.1
0.01
0.019 0.013
0.014 0.009
0.51
0.49
0.30
0.29
0.05
0.419
0.043
0.055
0.394
0.016
inches
0.1
0.012 0.096
0.004 0.089
0.043
0.039
0.01
0.01
Z
(1)
0.9
0.4
0.035
0.004
0.016
θ
o
8
o
0
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
Fig 9.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT163-1
075E04
MS-013
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
Package outline SOT163-1 (SO20)
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
13 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm
SOT360-1
E
D
A
X
c
HE
y
v M A
Z
11
20
Q
A2
(A 3)
A1
pin 1 index
A
θ
Lp
L
1
10
e
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.1
0.15
0.05
0.95
0.80
0.25
0.30
0.19
0.2
0.1
6.6
6.4
4.5
4.3
0.65
6.6
6.2
1
0.75
0.50
0.4
0.3
0.2
0.13
0.1
0.5
0.2
8
o
0
o
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT360-1
REFERENCES
IEC
JEDEC
JEITA
MO-153
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
Fig 10. Package outline SOT360-1 (TSSOP20)
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
14 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
13. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
13.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
13.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
•
•
•
•
•
•
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
13.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
15 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
13.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 11) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 6 and 7
Table 6.
SnPb eutectic process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
≥ 350
< 2.5
235
220
≥ 2.5
220
220
Table 7.
Lead-free process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
350 to 2000
> 2000
< 1.6
260
260
260
1.6 to 2.5
260
250
245
> 2.5
250
245
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 11.
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
16 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 11. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
14. Abbreviations
Table 8.
Abbreviations
Acronym
Description
CDM
Charged-Device Model
BiCMOS
Bipolar Complementary Metal-Oxide Semiconductor
DUT
Device Under Test
ESD
ElectroStatic Discharge
HBM
Human Body Model
I/O
Input/Output
I2C-bus
Inter-Integrated Circuit bus
MM
Machine Model
RC
Resistor Capacitor network
SMBus
System Management Bus
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
17 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
15. Revision history
Table 9.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
PCA9518_5
20081202
Product data sheet
-
PCA9518_4
Modifications:
•
The format of this data sheet has been redesigned to comply with the new identity guidelines of
NXP Semiconductors.
•
•
•
Legal texts have been adapted to the new company name where appropriate.
•
Figure 6 “Bus waveforms”:
Section 6.1 “Enable”: added new 3rd paragraph
Figure 5 “Typical application: multiple expandable 5-channel I2C-bus hubs”: added 2nd paragraph
below drawing.
– changed symbol from “tst” to “tstretch”
– changed symbol from “tr1” to “tPHL1”
– changed symbol from “tr2” to “tPHL2”
– changed symbol from “tEr1” to “tPLH2, tPLH1”
•
Table 3 “Limiting values”:
– changed symbol/parameter from “VCC to GND, supply voltage range VCC” to
“VCC, supply voltage” (and placed “VCC to GND” in Conditions column)
– changed symbol/parameter from “Vbus, voltage range I2C-bus, SCL or SDA” to
“VI2C-bus, I2C-bus voltage” (and placed “SCL or SDA” in Conditions column)
– changed symbol/parameter from “I, DC current (any pin)” to “II, input current” (and placed
“any pin” in Conditions column)
– changed parameter for Ptot from “power dissipation” to “total power dissipation”
•
Table 4 “Static characteristics”:
– sub-section “Supplies”; symbol ICCH: changed parameter from “quiescent supply current, both
channels HIGH” to “HIGH-level supply current”; moved “both channels HIGH” to Conditions
column
– sub-section “Supplies”; symbol ICCL: changed parameter from “quiescent supply current, both
channels LOW” to “LOW-level supply current”; moved “both channels LOW” to Conditions
column
– sub-section “Supplies”; symbol ICCLc: changed parameter from “quiescent supply current in
contention” to “contention LOW-level supply current”
– sub-section “Input SCL; input/output SDA”, symbol used for parameter “input leakage current”
changed from “II” to “ILI”
– sub-section “Input SCL; input/output SDA”, symbol VOL−VILc: parameter changed from “LOW
level input voltage below output LOW level voltage” to “difference between LOW-level output
and LOW-level input voltage contention”
– (old) table note 1 is split into (new) Table note [1] and Table note [2]
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
18 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
Table 9.
Revision history …continued
Document ID
Modifications:
(continued)
Release date
•
Data sheet status
Change notice
Supersedes
Table 5 “Dynamic characteristics”:
– symbol/parameter “tPHLs, Propagation delay SDA to SDAn or SCL to SCLn” changed to
“tPHL, HIGH to LOW propagation delay” (moved “SDA to SDAn or SCL to SCLn” to Conditions
column)
– symbol/parameter “tPLHs, Propagation delay SDA to SDAn or SCL to SCLn” changed to
“tPLH, HIGH to LOW propagation delay” (moved “SDA to SDAn or SCL to SCLn” to Conditions
column)
– symbol/parameter “tPHLE1s, Propagation delay EXPSDA1 to SDA or EXPSCL1 to SCL” changed
to “tPHL1, HIGH to LOW propagation delay 1” (moved “EXPSDA1 to SDA or EXPSCL1 to SCL” to
Conditions column)
– symbol/parameter “tPLHE1s, Propagation delay EXPSDA1 to SDA or EXPSCL1 to SCL” changed
to “tPLH1, LOW to HIGH propagation delay 1” (moved “EXPSDA1 to SDA or EXPSCL1 to SCL” to
Conditions column)
– symbol/parameter “tPLHE2s, Propagation delay EXPSDA2 to SDA or EXPSCL2 to SCL” changed
to “tPLH2, LOW to HIGH propagation delay 2” (moved “EXPSDA2 to SDA or EXPSCL2 to SCL” to
Conditions column)
– symbol/parameter “tTHLs, Transition time, SDA/SCL” changed to “tTHL, HIGH to LOW transition
time” (moved “SDA, SCL” to Conditions column)
– symbol/parameter “tTLHs, Transition time, SDA/SCL” changed to “tTLH, LOW to HIGH transition
time” (moved “SDA, SCL” to Conditions column)
– symbol/parameter “tSET, Enable to Start condition” changed to “tsu, set-up time” (moved “enable
to START condition” to Conditions column)
– symbol/parameter “tHOLD, Enable after Stop condition” changed to “th, hold time” (moved
“enable to START condition” to Conditions column)
•
Figure 7 “AC waveforms”: timing symbols updated as per symbol/parameter changes detailed
above for Table 5 “Dynamic characteristics”
PCA9518_4
20040929
(9397 750 14109)
Product data sheet
-
PCA9518_3
PCA9518_3
20040624
(9397 750 13253)
Product data sheet
-
PCA9518_2
PCA9518_2
20031110
(9397 750 12295)
Product data
ECN 853-2364 30410 PCA9518_1
dated 2003 Oct 03
PCA9518_1
20020820
(9397 750 10258)
Product data
ECN 853-2364 28791 dated 2002 Aug 20
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
19 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
PCA9518_5
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 05 — 2 December 2008
20 of 21
PCA9518
NXP Semiconductors
Expandable 5-channel I2C-bus hub
18. Contents
1
2
3
4
5
5.1
5.2
6
6.1
6.2
6.3
7
8
9
10
11
12
13
13.1
13.2
13.3
13.4
14
15
16
16.1
16.2
16.3
16.4
17
18
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
Functional description . . . . . . . . . . . . . . . . . . . 5
Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
I2C-bus systems . . . . . . . . . . . . . . . . . . . . . . . . 5
Application design-in information . . . . . . . . . . 6
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 9
Static characteristics. . . . . . . . . . . . . . . . . . . . 10
Dynamic characteristics . . . . . . . . . . . . . . . . . 11
Test information . . . . . . . . . . . . . . . . . . . . . . . . 12
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 13
Soldering of SMD packages . . . . . . . . . . . . . . 15
Introduction to soldering . . . . . . . . . . . . . . . . . 15
Wave and reflow soldering . . . . . . . . . . . . . . . 15
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 15
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 16
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18
Legal information. . . . . . . . . . . . . . . . . . . . . . . 20
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 20
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Contact information. . . . . . . . . . . . . . . . . . . . . 20
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 2 December 2008
Document identifier: PCA9518_5
Similar pages