UMA 0204, UMB 0207 Datasheet

UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
Ultra Precision Thin Film MELF Resistors
FEATURES
• Most advanced thin film technology
• Long term stability down to 0.02 %
• TCR down to ± 5 ppm/K
• High precision tolerance down to ± 0.02 %
• Operating voltage 350 V for UMB 0207
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
UMA 0204 and UMB 0207 ultra precision thin film MELF
resistors combine the proven reliability of precision MELF
products with the most advanced level of precision and
stability first achieved with axial thin film precision resistors.
This unique combination makes the product perfectly suited
for all applications with outstanding requirements towards
reliable precision and stability.
APPLICATIONS
• Measuring and calibration equipment
• Industrial process control systems
• Space and aircraft electronics
• Medical equipment
TECHNICAL SPECIFICATIONS
DESCRIPTION
UMA 0204
UMB 0207
0204
0207
Metric CECC size
RC 3715M
RC 6123M
Resistance range
22  to 332 k
100  to 390 k
DIN size
Resistance tolerance
± 0.25 %; ± 0.1 %; ± 0.05 %; ± 0.02 %
Temperature coefficient
± 15 ppm/K; ± 10 ppm/K; ± 5 ppm/K
Rated dissipation, P70 (1)
Operating voltage, Umax. ACRMS or DC
Permissible film temperature, max.
0.25 W
0.4 W
200 V
350 V
(1)
125 °C
Operating temperature range
-55 °C to 125 °C
Permissible voltage against ambient (insulation):
1 min; Uins
300 V
500 V
Continuous
75 V
75 V
Failure rate: FITobserved
0.1 x 109/h
Note
(1) Please refer to APPLICATION INFORMATION below.
Revision: 27-Mar-14
Document Number: 28715
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
APPLICATION INFORMATION
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow
support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is
not exceeded. Furthermore a high level of ambient temperature or of power dissipation may raise the temperature of the solder
joint, hence special solder alloys or board materials may be required to maintain the reliability of the assembly.
These resistors do not feature a lifetime limitation when operated within the limits of rated dissipation, permissible operating
voltage and permissible film temperature. However, the resistance typically increases due to the resistor’s film temperature over
operating time, generally known as drift. The drift may exceed the stability requirements of an individual application circuit and
thereby limits the functional lifetime.
MAXIMUM RESISTANCE AT RATED DISSIPATION
Operation mode
Rated dissipation, P70
Precision
Standard
UMA 0204
0.07 W
0.25 W
UMB 0207
0.11 W
0.4 W
85 °C
125 °C
 0.02 %
 0.05 %
Applied maximum film temperature, F max.
Max. resistance change at rated dissipation
|R/R max.|, after:
1000 h
8000 h
 0.05 %
 0.1 %
225 000 h
 0.15 %
 0.3 %
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE
TYPE
TCR
TOLERANCE
RESISTANCE RANGE
± 15 ppm/K
±0.05 %
47  to 332 k
±0.25 %
22  to 332 k
± 10 ppm/K
UMA 0204
± 5 ppm/K
± 15 ppm/K
± 10 ppm/K
UMB 0207
± 5 ppm/K
±0.1 %
43  to 332 k
± 0.05 %
75  to 221 k
±0.25 %
33  to 221 k
±0.1 %
56  to 221 k
± 0.05 %
75  to 150 k
± 0.02 %
75  to 100 k
±0.05 %
100  to 390 k
±0.25 %
100  to 390 k
±0.1 %
100  to 390 k
± 0.05 %
100  to 390 k
±0.25 %
270  to 390 k
±0.1 %
270  to 390 k
± 0.05 %
270  to 390 k
± 0.02 %
270  to 390 k
E-SERIES
E192
Notes
• TCR 10 ppm/K and TCR 05 ppm/K is specified over the temperature range from -10 °C to +85 °C.
• UMA 0204: Approval to EN 140401-803, “Version A” is achieved for TCR 10 ppm/K with 0.25 % and 0.1 %.
Revision: 27-Mar-14
Document Number: 28715
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
PACKAGING
TYPE
CODE
QUANTITY
CARRIER TAPE
WIDTH
PITCH
REEL DIAMETER
AU
100
A1
1000
A3 = AL
3000
A0
10 000
330 mm/13"
BU
100
Box
B1
1000
B2
2000
B7
7000
Box
Antistatic blister tape acc.
IEC 60286-3 type 2a
UMA 0204
8 mm
Antistatic blister tape acc.
IEC 60286-3 type 2a
UMB 0207
4 mm
12 mm
180 mm/7"
4 mm
180 mm/7"
330 mm/13"
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: UMB02070F5620AB200
U
M
B
0
2
0
7
0
F
5
6
2
0
A
B
2
0
0
MODEL/SIZE
VERSION
TCR
RESISTANCE
TOLERANCE
PACKAGING
UMA 0204
UMB 0207
0 = Standard
G = ± 5 ppm/K
F = ± 10 ppm/K
E = ± 15 ppm/K
3 digit value
1 digit multiplier
H = ± 0.02 %
A = ± 0.05 %
B = ± 0.1 %
C = ± 0.25 %
AU
A1
A3
A0
BU
B1
B2
B7
562R
MULTIPLIER
9 = *10-1
0 = *100
1 = *101
2 = *102
3 = *103
Product Description: UMB 0207-10 0.05 % B2 562R
UMB
0207
10
0.05 %
B2
TYPE
SIZE
TCR
TOLERANCE
PACKAGING
RESISTANCE
UMA
UMB
0204
0207
± 5 ppm/K
± 10 ppm/K
± 15 ppm/K
± 0.02 %
± 0.05 %
± 0.1 %
± 0.25 %
AU
A1
AL
A0
BU
B1
B2
B7
562R = 562 
Note
• Products can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION.
Revision: 27-Mar-14
Document Number: 28715
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
DESCRIPTION
Production is strictly controlled and follows an extensive set
of instructions established for reproducibility. A
homogeneous film of special metal alloy is deposited on a
high grade ceramic body (Al2O3) and conditioned to achieve
the desired temperature coefficient. Nickel plated steel
termination caps are firmly pressed on the metallized rods.
A special laser is used to achieve the target value by
smoothly cutting a helical groove in the resistive layer
without damaging the ceramics. The resistor elements are
covered by a unique protective coating designed for
electrical, mechanical, and climatic protection. The
terminations receive a final pure tin on nickel plating. Five
color code rings designate the resistance value and
tolerance in accordance with IEC 60062 (3).
The result of the determined production is verified by an
extensive testing procedure and optical inspection
performed on 100 % of the individual resistors. This includes
full screening for the elimination of products with a potential
risk of early field failures. Only accepted products are laid
directly into the blister tape in accordance with
IEC 60286-3, Type 2a (3).
ASSEMBLY
The resistors are suitable for processing on automatic SMD
assembly systems. They are suitable for automatic
soldering using reflow or vapour phase as shown in
IEC 61760-1 (3). Solderability is specified for 2 years after
production
or
requalification,
however,
excellent
solderability is proven after extended storage in excess of
10 years. The permitted storage time is 20 years.
Vishay Beyschlag
All products comply with the GADSL (1) and the
CEFIC-EECA-EICTA (2) list of legal restrictions on
hazardous substances. This includes full compliance with
the following directives:
• 2000/53/EC End of life Vehicle Directive (ELV) and Annex II
(ELV II)
• 2011/65/EU Restriction of the use of Hazardous
Substances Directive (RoHS)
• 2002/96/EC Waste Electrical and Electronic Equipment
Directive (WEEE)
APPROVALS
Where applicable the resistors are approved within the
IECQ-CECC Quality Assessment System for Electronic
Components to the detail specification EN 140401-803
which refers to EN 60115-1, EN 140400 and the variety of
environmental test procedures of the IEC 60068 (3) series.
Vishay
Beyschlag
has
achieved
“Approval
of
Manufacturer” in accordance with IECQ 03-1. The release
certificate for “Technology Approval Schedule” in
accordance with CECC 240001 based on IECQ 03-3 is
granted for the Vishay Beyschlag manufacturing process.
RELATED PRODUCTS
For products with a wider range of TCR, tolerance and
resistance, see the datasheets:
• “Professional Thin Film MELF Resistors” 
(www.vishay.com/doc?28713)
• “Precision Thin Film MELF Resistors” 
(www.vishay.com/doc?28714)
The resistors are completely lead (Pb)-free, the pure tin
plating provides compatibility with lead (Pb)-free soldering
processes. The immunity of the plating against tin whisker
growth has been proven under extensive testing.
The encapsulation is resistant to all cleaning solvents
commonly used in the electronics industry, including
alcohols, esters and aqueous solutions. The suitability of
conformal coatings, if applied, shall be qualified by
appropriate means to ensure the long-term stability of the
whole system.
Notes
(1) Global Automotive Declarable Substance List, see www.gadsl.org.
(2) CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association).
(3) The quoted IEC standards are also released as EN standards with the same number and identical contents.
Revision: 27-Mar-14
Document Number: 28715
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
Power Dissipation P
FUNCTIONAL PERFORMANCE
0.15
W
UMB 0207
UMA 0204
0.10
0.05
0
-50
0
50
70
100
°C
150
Ambient Temperature ϑamb
Power Dissipation P
Derating - Precision Operation Mode
0.4
W
UMB 0207
UMA 0204
0.3
0.2
0.1
0
-50
0
50
70
100
°C
150
Ambient Temperature ϑamb
Current Noise A1
Derating - Standard Operation Mode
1
µV/ V
0.1
UMA 0204
UMB 0207
0.01
100 Ω
1 kΩ
10 kΩ
100 kΩ
1 MΩ
10 MΩ
Resistance Value R
Current Noise - A1
Revision: 27-Mar-14
In accordance with IEC 60195
Document Number: 28715
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
TESTS AND REQUIREMENTS
Essentially all tests are carried out in accordance with the
following specifications.
EN 60 115-1, generic specification
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
EN 140400, sectional specification
EN 140401-803, detail specification
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The
components
are
approved
under
the
IECQ-CECC-system, where applicable. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/ECA-703 and JIS-C-52001-1.
The components are mounted for testing on printed-circuit
boards in accordance with EN 140400, 2.3.3, unless
otherwise specified.
The tests are carried out in accordance with IEC 60068 and
under standard atmospheric conditions in accordance with
IEC 60068-1, 5.3. A climatic category is applied, defined by
the lower category temperature (LCT), the upper category
temperature (UCT), and the number of days of the damp
heat, steady-state test (56).
The requirements stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140401-803. However, some
additional tests and a number of improvements against
those minimum requirements have been included.
TEST PROCEDURES AND REQUIREMENTS
IEC
EN
60068-2 (1)
60115-1
TEST
CLAUSE
METHOD
TEST
STABILITY
CLASS 0.05
OR BETTER
STABILITY
CLASS 0.1
OR BETTER
STABILITY
CLASS 0.25
OR BETTER
UMA 0204
100  to 100 k
43  to 221 k
22  to 332 k
UMB 0207
270  to 100 k
100  to 390 k
-
Stability for product types:
4.5
-
4.8.4.2
-
Resistance
Temperature
coefficient
Endurance at
70 °C:
Precision
operation mode
4.25.1
Endurance at
70 °C:
Standard
operation mode
4.25.3
4.24
4.37
-
± 0.25 % R; ±0.1 % R; ± 0.05 % R; ± 0.02 % R
At (20/-10/20) °C and
(20/85/20) °C
± 10 ppm/K; ± 5 ppm/K
At (20/-55/20) °C and
(20/125/20) °C
± 15 ppm/K
U = P 70 x R Umax.;
1.5 h on; 0.5 h off;
70 °C; 1000 h
± (0.02 % R + 1 m)
70 °C; 8000 h
±(0.05 % R + 1 m)
U = P 70 x R Umax.;
1.5 h on; 0.5 h off;
70 °C; 1000 h
±(0.05 % R + 1 m)
70 °C; 8000 h
± (0.1 % R + 1 m)
85 °C; 1000 h
±(0.01 % R + 1 m) ± (0.05 % R + 1 m)
±(0.1 % R + 1 m)
125 °C; 1000 h
± (0.05 % R + 1 m)
±(0.1 % R + 1 m)
±(0.15 % R + 1 m)
±(0.03 % R + 1 m) ±(0.05 % R + 1 m)
±(0.1 % R + 1 m)
-
Endurance at
upper category
temperature
78 (Cab)
Damp heat,
steady state
(40 ± 2) °C; 56 days;
(93 ± 3) % RH
-
Damp heat,
steady state,
accelerated;
Standard
operation mode
(85 ± 2)C; (85 ± 5) % RH;
U = 0.3 x P 70 x R
0.3 x Umax.;
1000 h
Revision: 27-Mar-14
REQUIREMENTS
PERMISSIBLE CHANGE (R)
PROCEDURE
±(0.1 % R + 1 m)
±(0.25 % R + 1 m)
Document Number: 28715
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
TEST PROCEDURES AND REQUIREMENTS
IEC
EN
60068-2 (1)
60115-1
TEST
CLAUSE
METHOD
TEST
Stability for product types:
STABILITY
CLASS 0.05
OR BETTER
STABILITY
CLASS 0.1
OR BETTER
STABILITY
CLASS 0.25
OR BETTER
UMA 0204
100  to 100 k
43  to 221 k
22  to 332 k
UMB 0207
270  to 100 k
100  to 390 k
-
Climatic
sequence:
4.23
4.23.2
2 (Ba)
Dry heat
UCT; 16 h
4.23.3
30 (Db)
Damp heat,
cyclic
55 °C; 24 h; 90 % RH;
1 cycle
4.23.4
1 (Aa)
Cold
LCT; 2 h
4.23.5
13 (M)
Low air pressure
8.5 kPa; 2 h; (25 ± 10) °C
4.23.6
30 (Db)
Damp heat,
cyclic
55 °C; 24 h;90 % RH;
5 cycles
4.23.7
-
DC load
U=
P 70 x R Umax.;
1 min.
LCT = -10 °C; UCT = 85 °C
LCT = -55 °C; UCT = 125 °C
-
REQUIREMENTS
PERMISSIBLE CHANGE (R)
PROCEDURE
1 (Aa)
Cold
± (0.03 % R + 1 m) ± (0.05 % R + 1 m)
-
-55 °C; 2 h
-
± (0.1 % R + 1 m)
±(0.02 % R + 0.1 m)
30 min at LCT;
30 min at UCT;
LCT = -10 °C; UCT = 85 °C
4.19
14 (Na)
Rapid change
of temperature
5 cycles
±(0.01 % R + 1 m) ± (0.02 % R + 1 m)
-
1000 cycles
± (0.05 % R + 1 m) ± (0.05 % R + 1 m)
-
LCT = -55 °C; UCT = 125 °C
4.13
-
5 cycles
-
-
± (0.025 % R + 1 m)
1000 cycles
-
-
± (0.1 % R + 1 m)
Short time
overload;
Precision
operation mode
U = 2.5 x P 70 x R
2 x Umax.; 5 s
±(0.005 % R + 1 m)
Short time
overload;
Standard
operation mode
U = 2.5 x P 70 x R
2 x Umax.; 5 s
±(0.01 % R + 1 m)
Severity no. 4:
U = 10 x P 70 x R
2 x Umax.;
10 pulses 10 μs/700 μs
± (0.25 % R + 5 m)
15 x P 70 x R
2 x Umax.
0.1 s on; 2.5 s off;
1000 cycles
±(0.5 % R + 5 m)
Endurance by sweeping;
10 Hz to 2000 Hz;
no resonance; amplitude
1.5 mm or  200 m/s2;
7.5 h
±(0.01 % R + 1 m)
4.27
-
Single pulse high
voltage overload;
Standard
operation mode
4.39
-
Periodic electric
overload;
Standard
operation mode
4.22
6 (Fc)
Revision: 27-Mar-14
Vibration
± (0.01 % R + 1 m)
U=
Document Number: 28715
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
TEST PROCEDURES AND REQUIREMENTS
IEC
EN
60068-2 (1)
60115-1
TEST
CLAUSE
METHOD
TEST
Stability for product types:
4.38
4.17.2
4.18.2
-
58 (Td)
58 (Td)
Electrostatic
discharge
(Human Body
Model)
Solderability
Resistance to
soldering heat
REQUIREMENTS
PERMISSIBLE CHANGE (R)
PROCEDURE
STABILITY
CLASS 0.05
OR BETTER
STABILITY
CLASS 0.1
OR BETTER
STABILITY
CLASS 0.25
OR BETTER
UMA 0204
100  to 100 k
43  to 221 k
22  to 332 k
UMB 0207
270  to 100 k
100  to 390 k
-
(1);
IEC 61340-3-1
3 pos. + 3 neg. discharges
UMA 0204: 2 kV
UMB 0207: 4 kV
(0.5 % R + 50 m)
Solder bath method;
SnPb40; non-activated flux;
(215 ± 3) °C; (3 ± 0.3) s
Good tinning ( 95 % covered); no visible damage
Solder bath method;
SnAg3Cu0.5 or SnAg3.5;
non-activated flux;
(235 ± 3) °C; (2 ± 0.2) s
Good tinning ( 95 % covered); no visible damage
Solder bath method;
(260 ± 5) °C; (2 ± 0.2) s
Reflow method 2
(IR/forced gas convection);
(260 ± 5) °C; (10 ± 1) s
(2)
±(0.05 % R + 10 m)
±(0.01 % R + 1 m)
±(0.02 % R + 1 m)
4.29
45 (XA)
Component
solvent
resistance
Isopropyl alcohol; 50 °C;
method 2
No visible damage
4.30
45 (XA)
Solvent
resistance of
marking
Isopropyl alcohol; 50 °C;
method 1, toothbrush
Marking legible; no visible damage
4.32
21 (Ue3)
Shear (adhesion)
45 N
No visible damage
4.33
21 (Ue1)
Substrate
bending
Depth 2 mm, 3 times
4.7
-
Voltage proof
URMS = Uins; 60 s
No flashover or breakdown
Flammability
IEC 60695-11-5 (1),
needle flame test; 10 s
No burning after 30 s
4.35
-
No visible damage, no open circuit in bent position
(0.02 % R + 10 m)
(0.05 % R + 10 m)
Notes
(1) The quoted IEC standards are also released as EN standards with the same number and identical contents.
(2) Wave soldering is not recommended.
Revision: 27-Mar-14
Document Number: 28715
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
UMA 0204, UMB 0207
www.vishay.com
Vishay Beyschlag
DIMENSIONS
L
K
L1
D
D1
DIMENSIONS AND MASS
L
(mm)
D
(mm)
L1 min.
(mm)
D1
(mm)
UMA 0204
3.6 + 0/- 0.2
1.4 + 0/- 0.1
1.8
UMB 0207
5.8 + 0/- 0.15
2.2 + 0/- 0.2
3.2
TYPE
K
(mm)
MASS
(mg)
D + 0/- 0.15
0.8 ± 0.1
22
D + 0/- 0.2
1.15 ± 0.1
80
Note
• Color code marking is applied according to IEC 60062 in five bands. Each color band appears as a single solid line, voids are permissible if
at least 2/3 of the band is visible from each radial angle of view. The last color band for tolerance is approximately 50 % wider than the other
bands. An interrupted band between the 4th and 5th full band indicates the temperature coefficient (orange = TCR 15 ppm/K, blue = TCR
10 ppm/K, violet = TCR 05 ppm/K).
PATTERN STYLES FOR MELF RESISTORS
X
G
Y
Z
RECOMMENDED SOLDER PAD DIMENSIONS
WAVE SOLDERING (1)
TYPE
REFLOW SOLDERING
G
(mm)
Y
(mm)
X
(mm)
Z
(mm)
G
(mm)
Y
(mm)
X
(mm)
Z
(mm)
UMA 0204
1.5
1.5
1.8
4.5
1.7
1.2
1.6
4.1
UMB 0207
2.8
2.1
2.6
7.0
3.2
1.7
2.4
6.6
Notes
• The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or
in publication IPC-7351. They do not guarantee any supposed thermal properties, however, they will be found adequate for most general
applications.
(1) Wave soldering is not recommended.
Revision: 27-Mar-14
Document Number: 28715
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000