CC8 Datasheet

CC8
www.vishay.com
Vishay Electro-Films
Thin Film 0202 Size Resistor on Alumina
FEATURES
•
•
•
•
•
•
•
Chip size: 0.020 inches square
Wire bondable
Resistance range: 20  to 20 k
Alumina substrate
Case: 0202
Low stray capacitance: < 0.2 pF
Resistor material: Nichrome with passivation
coat
• Tolerances to 0.5 %
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
Product may not be to scale
The CC8 series resistor chips offer a combination of low
shunt capacitance, small size and excellent stability.
The CC8s are manufactured using Vishay Electro-Films (EFI)
sophisticated thin film equipment and manufacturing
technology. The CC8s are 100 % electrically tested and
visually inspected to MIL-STD-883, class H or class K.
APPLICATIONS
Vishay EFI CC8 chip resistors provide excellent
high-frequency response and are ideally suited for
prototyping. 
Typical application areas are:
• Amplifiers
• Oscillators
• Attenuators
• Couplers
• Filters
Recommended for hermetic environment where die is not
exposed to moisture.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
VALUE
UNIT
20 to 20K
± 0.5
± 25, ± 50, ± 100

%
ppm/°C
Tightest Standard Tolerance Available
0.5 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
20 Ω
50 Ω
5.1 kΩ
20 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
VALUE
UNIT
- 20 dB typ.
dB
Moisture Resistance, MIL-STD-202
Method 106 (Passivated Film)
± 0.5 max. R/R
%
Stability, 1000 h, + 125 °C, 25 mW
± 0.2 max. R/R
%
- 55 to + 125
°C
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
± 0.25 max. R/R
%
High Temperature Exposure, + 150 °C, 1000 h
± 0.5 max. R/R
%
Noise, MIL-STD-202, Method 308
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to zero at + 150 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Revision: 05-Apr-13
400
V
1012 min.

100 max.
V
0.035 max.
W
± 0.25 max. R/R
%
Document Number: 61007
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CC8
www.vishay.com
Vishay Electro-Films
DIMENSIONS in inches
0.020
0.020
0.020
0.020
0.004
0.004
0.008
0.015
TYPICAL RANGE
110 Ω to 20 kΩ
TYPICAL RANGE
20 Ω to 100 Ω
SCHEMATIC
MECHANICAL SPECIFICATIONS
PARAMETER
VALUE
Chip Size
0.020" x 0.020" ± 0.003" (0.5 mm x 0.5 mm ± 0.08 mm)
Chip Thickness
0.010" ± 0.002" (0.25 mm ± 0.05 mm)
Chip Substrate Material
99.6 % alumina, 2 μ" to4 μ" finish
Resistor Material
Nichrome
Bonding Pad Size
0.004" x 0.008" (0.10 mm x 0.20 mm) minimum
Number of Pads
2
Pad Material
25 k minimum gold standard
Passivation
Thermalset plastic
Backing
None
GLOBAL PART NUMBER INFORMATION
GLOBAL PART NUMBER: CC8-12500KKSSNHWS
GLOBAL PART NUMBER DESCRIPTION: CC8 1.25K 10 % 100 ppm Std SnPb None H WS
C
C
8
-
1
MODEL
RESISTANCE
RESISTANCE
MULTIPLIER
CODE
CC8-
First 4 digits
are significant
figures of
resistance
B = 0.01
A = 0.1
0=1
1 = 10
Revision: 05-Apr-13
2
5
0
0
K
TOLERANCE
CODE
TCR
(ppm/°C)
TRIM
STYLE
B = 0.1 %
C = 0.25 %
D = 0.5 %
F = 1.0 %
G = 2.0 %
J = 5.0 %
K = 10 %
E = ± 25
C = ± 50
K = ± 100
E = Edg
S = Std
U = Usr
N = Nitride
K
S
TERMINATION
G = Au
S = SnPb
A = Al
T = Lead
(Pb)-free (e1)
S
N
BACK
METAL
H
VISUAL
CLASS
W
S
PACK CODE
17
G = Au H = Class H WS = Waffle
N = None K = Class K pack 100 min.,
1 mult
Document Number: 61007
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000