APD-128G064A-1 Datasheet

APD-128G064A-1
Vishay Dale
Plasma Display Modules
128 x 64 Graphics Display with Drive Electronics,
TTL Level Data Interface and DC to DC Converter
FEATURES
• TTL level video interface
• Highly visible for long distance viewing
• On board DC converter
• Slim profile
• Large, bright characters and graphics
The APD-128G064A-1 DC plasma display offers viewing qualities designers seek such as high contrast, viewing angle of 150°
minimum and long distance readability. Its bright (50 foot lambert minimum) with characters and graphics figures presented in
a pleasing neon orange color against a black background. Plasma is much more readable and eye-pleasing than liquid crystal
or vacuum fluorescent displays and is filterable to red, amber or neutral density.These plasma display panels are driven in a
standard row-column refresh method much like a CRT display.
The designer need only supply TTL level signals for SERIAL DATA, DOT CLOCK, COLUMN LATCH, ROW DATA, ROW
CLOCK and DISPLAY ENABLE. The SERIAL DATA is entered with the DOT CLOCK up to frequencies as high as 8mHz. After
a row of 128 pixels is clocked in, the COLUMN LATCH signal is toggled and the data is latched. At the time the data is latched,
the display is briefly disabled using the DISPLAY ENABLE signal, then the row pointer is advanced with the ROW CLOCK
signal. Once each frame the ROW DATA must be asserted to synchronize the column serial data with the beginning row. The
recommended scanning frequency is approximately 70 Hz, but may be as high as 200 Hz. The high clock rate on the data clock
allows for rapid refresh and maximum access time to the refresh ram.
ELECTRICAL SPECIFICATIONS
DIMENSIONS in inches [millimeters]
Power Required: Typical = 12 watts.
128 x 64 Full Field
14.50 [368.30]
Maximum = 35 watts.
Column 1,
Row 1
STANDARD ELECTRICAL SPECIFICATIONS*
DESCRIPTION
Logic Supply
Logic Current
DC-DC Supply
DC-DC Current**
Logic 1 Input
Logic 0 Input
SYMBOL
MIN.
TYP.
MAX.
UNITS
Vcc
Icc
VDC
Idc
Vih
Vil
+ 4.5
—
+ 12.0
0.080
2.0
—
+ 5.0
0.050
+ 24.0
0.750
—
—
+ 5.5
—
+ 30.0
1.5
—
0.8
VDC
Amps
VDC
Amps
VDC
VDC
*Recommended operating voltages. All maximums are to be
considered absolute maximum.
**Current is calculated at VDC = 24 VDC. The initial power on
condition may require 2X maximum rating to initiate DC voltage
conversion circuit.
.150
[3.81]
7.40 [187.96]
7.825
[198.76]
6.35
[161.29]
7.275
[184.78]
Center of
Display Area
8.125
[206.38]
4.062
[103.17]
.487
[12.37]
.888
[22.56]
13.775 [349.88]
1.025
14.80 [375.92]
[26.04]
Pin #1 of P1
.447
± .020
[11.35
.062 [1.575]
± .508]
6.750 [165.10]
Pin #1
PCB
of
P3
Thickness
CL
7.40 [187.96]
7.25 [184.15]
.150
[3.81]
12.75 [323.85]
8.775 [222.88]
10.50 [266.70]
CL
CL
ORDERING INFORMATION
DESCRIPTION
PART NUMBER
Display Module with Drivers and TTL Interface ............................................................................................. APD-128G064A
Display Module with Drivers, TTL Interface and On Board DC Converter ................................................. APD-128G064A-1
Data Connector Kit ................................................................................................................................................. 280105-05
Power Connector Kit .............................................................................................................................................. 280108-13
www.vishay.com
2
Document Number: 37035
Revision 08-Nov-00
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
Similar pages