25A/37.5W

Technical
S pecification
PQ60015EGL25
48V in
1.5Vout
25Amp
2000Vdc
Eighth-brick
Input
Output
Current
Isolation
DC/DC Conver ter
Th e P Q6 0015EG L2 5 Pow erQ or ® G iga eig hth -brick con v er t er is a n ext -g e ner a ti on , b oa r d- mo un t ab l e, iso la t ed , fixed
s wit ch ing freq u enc y D C/D C c on ver t er t ha t u ses s y nch r o n ou s r ect ifi ca ti on t o a ch iev e ext r emel y h ig h co nv er s ion effi c ienc y. Th e po w er d iss ip at ed by th e c on v er te r i s s o lo w
t h at a h ea t sin k i s no t r eq ui red , w h ich s a ves cos t , w eig h t ,
h eig h t , an d ap p lic at io n ef for t . Al l o f th e p ow e r a nd co nt r ol
c omp on ent s ar e mou nt ed to t h e mul t i-l a yer PC B s ub s tr a t e
with h igh -y iel d sur fac e mo un t tec hnology. Si nce the
Powe rQ or co nver ter has n o ex plicit th er mal in terf ac es, it is
extremely reliable. RoHS compliant (see page 12 ).
Operational Features
PQ60015EGL25 Module
• High efficiency, >83% at full rated load current
• Delivers up to 25 amps of output current with minimal
derating - no heatsink required
• Wide input voltage range: 35V – 75V, with 100V
100ms input voltage transient capability
• Fixed frequency switching provides predictable EMI
performance
• No minimum load requirement means no preload
resistors required
Mechanical Features
• Industry standard eighth-brick pin-out configuration
• Industry standard size: 0.90” x 2.3” (22.9x58.4mm)
• Total height only 0.335” (8.5mm), permits better airflow
and smaller card pitch
• Total weight: 0.68 oz. (19 grams)
• Flanged pins designed to permit surface mount soldering (avoid wave solder) using FPiP technique
Contr ol Features
• On/Off control referenced to input side (positive and
negative logic options are available)
• Remote sense for the output voltage compensates for
output distribution drops
• Output voltage trim permits custom voltages and voltage
margining
Product # PQ60015EGL25
Phone 1-888-567-9596
www.synqor.com
Pr otection Features
• Input under-voltage lockout disables converter at low
input voltage conditions
• Output current limit and short circuit protection protects
converter and load from permanent damage and consequent hazardous conditions
• Active back bias limit prevents damage to converter
from external load induced pre-bias
• Output over-voltage protection protects load from damaging voltages
• Thermal shutdown protects converter from abnormal
environmental conditions
Safety Features
• 2000V, 30 MW input-to-output isolation provides
input/output ground separation
• UL 60950-1 recognized (US & Canada), basic insulation rating
• TUV certified to EN60950-1
• Meets 72/23/EEC and 93/68/EEC directives which
facilitates CE Marking in user’s end product
• Board and plastic components meet UL94V-0 flammability requirements
Doc.# 005-2EG651D Rev. B
1/22/08
Page 1
Input:
Output:
Current:
Package:
Technical Specification
MECHANICAL
DIAGRAM
0.14
2.30
(3.6)
(58.4)
35-75 V
1.5 V
25 A
Eighth-brick
0.90
(22.9)
0.450
(11.43)
Top View
0.15
0.300
2.00
0.150
(50.8)
(3.81)
1
8
7
2
6
5
3
4
(3.8)
(7.62)
0.600
(15.24)
Overall height
0.349 +0.015
Side View
(8.86 +0.38)
Bottom side
Clearance
EGA Option
0.424 (10.76)
max height
See Note 9
0.019 +0.013
(0.48 +0.33)
Lowest
Component
Flanged Pin
See Note 10
Load Board
EGA Option
0.076 (1.93)
min clearance
See Note 9
0.110
(2.79)
See Note 3
See Note 9
NOTES
PIN DESIGNATIONS
1) Pins 1-3, 5-7 are 0.040” (1.02mm) diameter. with 0.080”
(2.03mm) diameter standoff shoulders.
2) Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100”
(2.54 mm) diameter standoff shoulders.
3) Other pin extension lengths available. Recommended pin
length is 0.03” (0.76mm) greater than the PCB thickness.
4) All Pins: Material - Copper Alloy
Finish - Tin/Lead over Nickel plate
5) Undimensioned components are shown for visual reference only.
6) All dimensions in inches (mm)
Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
7) Weight: 0.68 oz. (19 g) typical
8) Workmanship: Meets or exceeds IPC-A-610C Class II
9) Modules ordered as an EGA option have different pins to provide a minimum bottom side clearance of 0.076” while increasing maximum height to 0.424”. See ordering page for more
information.
10) The flanged pins are designed to permit surface mount
soldering (allowing to avoid the wave soldering process)
through the use of the flanged pin-in-paste technique.
Product # PQ60015EGL25
Phone 1-888-567-9596
Pin No.
Name
Function
1
Vin(+)
Positive input voltage
2
ON/OFF
TTL input to turn converter
on and off, referenced to
Vin(-), with internal pull up.
3
Vin(–)
Negative input voltage
4
Vout(–)
Negative output voltage
5
SENSE(–)
Negative remote sense1
6
TRIM
Output voltage trim2
7
SENSE(+)
Positive remote sense3
8
Vout(+)
Positive output voltage
Notes:
1. SENSE(–) should be connected to Vout(–) either remotely or at the converter.
2. Leave TRIM pin open for nominal output voltage.
3. SENSE(+) should be connected to Vout(+) either remotely or at the converter.
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 2
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
PQ60015EGL25 ELECTRICAL CHARACTERISTICS
TA=25°C, airflow rate=300 LFM, Vin=48Vdc unless otherwise noted; full operating temperature range is -40°C to +100°C ambient temperature with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max.
Units
100
80
100
2000
100
125
18
V
V
V
V
°C
°C
V
Notes & Conditions
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Operating Transient Protection
Isolation Voltage (input to output)
Operating Temperature
Storage Temperature
Voltage at ON/OFF input pin
INPUT CHARACTERISTICS
Operating Input Voltage Range
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Maximum Input Current
No-Load Input Current
Disabled Input Current
Inrush Current Transient Rating
Response to Input Transient
Input Reflected Ripple Current
Input Terminal Ripple Current
Recommended Input Fuse
Input Filter Component Values (L\C)
Recommended External Input Capacitance
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise1
Peak-to-Peak
RMS
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Voltage
Back-Drive Current Limit while Enabled
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
-40
-55
-2
35
48
75
V
31.5
29.5
2.2
33.3
31.0
2.3
34.4
32.4
2.4
0.9
V
V
V
A
mA
mA
A2s
mV
mA
mA
A
µH\µF
µF
25
2
50
3.0
210
4.7\1.0
47
1.485
1.46
0
40
DYNAMIC CHARACTERISTICS
Input Voltage Ripple Rejection
Output Voltage during Load Current Transient
For a Step Change in Output Current (0.1A/µs)
For a Step Change in Output Current (5A/µs)
Settling Time
Turn-On Transient
Turn-On Time
Start-Up Inhibit Time
Output Voltage Overshoot
EFFICIENCY
100% Load
50% Load
180
5
0.01
10
1.50
1.515
V
+0.05 \ 2
+0.1 \ 2
+6
+0.1 \ 5
+0.2 \ 5
+20
1.54
%\mV
%\mV
mV
V
75
18
130
25
25
mV
mV
A
A
V
A
mA
µF
28.5
0.7
0.45
63
100
45,000
1000V/ms input transient
RMS thru 10µH inductor; Figures 13 & 15
RMS; Figures 13 & 14
Fast blow external fuse recommended
Internal values; Figure E
Typical ESR 0.1-0.2W; Figure 13
Over sample, line, load, temperature & life
20MHz bandwidth; Figures 13 & 16
Full Load; Figures 13 & 16
Full Load; Figures 13 & 16
Subject to thermal derating; Figures 5 - 8
Output Voltage 10% Low; Figure 17
Negative current drawn from output
“
1.5Vout at 25A Resistive Load
dB
120 Hz; Figure 20
80
150
300
mV
mV
µs
50% to 75% to 50% Iout max; Figure 11
50% to 75% to 50% Iout max; Figure 12
To within 1% Vout nom
ms
ms
%
Full load, Vout=90% nom.; Figures 9 & 10
-40°C to +125°C; Figure F
45,000 µF load capacitance, Iout = 0A
%
%
Figures 1 - 4
Figures 1 - 4
°C
°C
°C
Package rated to 150°C
UL rated max operating temp 130°C
See Figures 5 - 8 for derating curves
14
200
0
TEMPERATURE LIMITS FOR POWER DERATING CURVES
Semiconductor Junction Temperature
Board Temperature
Transformer Temperature
Isolation Voltage (dielectric strength)
Isolation Resistance
Isolation Capacitance2
100% Load, 35 Vin
80
18
240
83.5
86
ISOLATION CHARACTERISTICS
Continuous
Continuous
100ms transient, square wave
Basic insulation, Pollution Degree 2
125
125
125
2000
30
470
V
MW
pF
Note 1: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: [email protected])
Note 2: Higher values of isolation capacitance can be added external to the module.
Product # PQ60015EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 3
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
ELECTRICAL CHARACTERISTICS (Continued)
Parameter P
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control (Option P)
Off-State Voltage
On-State Voltage
ON/OFF Control (Option N)
Off-State Voltage
On-State Voltage
ON/OFF Control (Either Option)
Pull-Up Voltage
Pull-Up Resistance
Output Voltage Trim Range
Output Voltage Remote Sense Range
Output Over-Voltage Protection
Over-Temperature Shutdown
Over-Temperature Shutdown Restart Hysteresis
Load Current Scale Factor
Min.
Typ.
Max.
Units
195
225
255
kHz
-2
2.4
0.8
18
V
V
2.4
-2
18
0.8
V
V
15
V
kW
%
%
%
°C
°C
-20
Vin/6
40
120
RELIABILITY CHARACTERISTICS
Calculated MTBF (Telcordia)
Calculated MTBF (MIL-217)
Field Demonstrated MTBF
125
125
10
800
+10
+10
130
Notes & Conditions
Regulation and Isolation stages
Figures A & B
Measured across Pins 8 & 4; Figure C
Measured across Pins 8 & 4
Over full temp range; % of nominal Vout
Average PCB Temperature
See web app. note Output Load Current Calc.
10 Hrs. TR-NWT-000332; 80% load,300LFM, 40oC Ta
106 Hrs. MIL-HDBK-217F; 80% load, 300LFM, 40oC Ta
106 Hrs. See our website for details
6
2.5
1.1
STANDARDS COMPLIANCE
Parameter P
Notes
STANDARDS COMPLIANCE
UL/cUL 60950-1
EN60950-1
72/23/EEC
93/68/EEC
Needle Flame Test (IEC 695-2-2)
IEC 61000-4-2
GR-1089-CORE
Telcordia (Bellcore) GR-513
File # E194341, Basic insulation & pollution degree 2
Certified by TUV
Test on entire assembly; board & plastic components UL94V-0 compliant
ESD test, 8kV - NP, 15kV air - NP (Normal Performance)
Section 7 - electrical safety, Section 9 - bonding/grounding
• An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety
certificates on new releases or download from the SynQor website.
QUALIFICATION TESTING
Parameter P
QUALIFICATION TESTING
Life Test
Vibration
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
Solderability
# Units
32
5
5
10
5
5
5
15 pins
Test Conditions
95% rated Vin and load, units at derating point, 1000 hours
10-55Hz sweep, 0.060” total excursion,1 min./sweep, 120 sweeps for 3 axis
100g minimum, 2 drops in x and y axis, 1 drop in z axis
-40°C to 100°C, unit temp. ramp 15°C/min., 500 cycles
Toperating = min to max, Vin = min to max, full load, 100 cycles
Tmin-10°C to Tmax+10°C, 5°C steps, Vin = min to max, 0-105% load
85°C, 85% RH, 1000 hours, 2 minutes on and 6 hours off
MIL-STD-883, method 2003
• Extensive characterization testing of all SynQor products and manufacturing processes is performed to ensure that we supply
robust, reliable product. Contact the factory for official product family qualification documents.
OPTIONS
PATENTS
SynQor provides various options for Packaging, Enable Logic,
and Feature Set for this family of DC/DC converters. Please consult the last page for information on available options.
SynQor is protected under various patents. Please consult the
last page for further details.
Product # PQ60015EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 4
Input:
Output:
Current:
Package:
95
88
90
87
85
86
Efficiency (%)
Efficiency (%)
Technical Specification
80
75
70
35 Vin
65
48 Vin
35-75 V
1.5 V
25 A
Eighth-brick
85
84
83
82
25 C
40 C
81
55 C
75 Vin
60
80
0.0
2.5
5.0
7.5
10.0
12.5
15.0
17.5
20.0
22.5
25.0
0
100
200
300
400
500
Air Flow (LFM)
Load Current (A)
Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25°C.
Figure 2: Efficiency at nominal output voltage and 60% rated power vs.
airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C
(nominal input voltage).
5.0
9
Power Dissipation (W)
Power Dissipation (W)
8
7
6
5
4
3
2
35 Vin
1
48 Vin
75 Vin
0
0
3
5
8
10
13
15
18
20
23
4.0
3.0
2.0
25 C
1.0
40 C
55 C
0.0
0
25
100
200
300
400
500
Air Flow (LFM)
Load Current (A)
Figure 3: Power dissipation at nominal output voltage vs. load current
for minimum, nominal, and maximum input voltage at 25°C.
Figure 4: Power dissipation at nominal output voltage and 60% rated
power vs. airflow rate for ambient air temperatures of 25°C, 40°C, and
55°C (nominal input voltage).
26
24
22
20
18
Iout (A)
16
14
12
10
400 LFM (2.0 m/s)
8
300 LFM (1.5 m/s)
6
200 LFM (1.0 m/s)
4
100 LFM (0.5 m/s)
2
50 LFM (0.25 m/s)
0
0
25
40
55
70
Semiconductor junction temperature
is within 1°C of surface temperature
85
o
Ambient Air Temperature ( C)
Figure 5: Maximum output power derating curves vs. ambient air temperature for airflow rates of 50 LFM through 400 LFM with air flowing
across the converter from pin 3 to pin 1 (nominal input voltage).
Product # PQ60015EGL25
Phone 1-888-567-9596
Figure 6: Thermal plot of converter at 25 amp load current with 55°C
air flowing at the rate of 200 LFM. Air is flowing across the converter
sideways from pin 3 to pin 1 (nominal input voltage).
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 5
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
26
24
22
20
18
Iout (A)
16
14
12
10
400 LFM (2.0 m/s)
8
300 LFM (1.5 m/s)
6
200 LFM (1.0 m/s)
4
100 LFM (0.5 m/s)
2
50 LFM (0.25 m/s)
0
0
25
40
55
70
Semiconductor junction temperature is
within 1°C of surface temperature
85
o
Ambient Air Temperature ( C)
Figure 7: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 50 LFM through 400 LFM with air flowing
from input to output (nominal input voltage).
Figure 8: Thermal plot of converter at 25 amp load current with 55°C
air flowing at the rate of 200 LFM. Air is flowing across the converter
from input to output (nominal input voltage).
Figure 9: Turn-on transient at full load (resistive load) (5 ms/div).
Input voltage pre-applied. Ch 1: Vout (500mV/div). Ch 2: ON/OFF
input (5V/div)
Figure 10: Turn-on transient at zero load (4 ms/div). Ch 1: Vout
(500mV/div). Ch 2: ON/OFF input (5V/div).
Figure 11: Output voltage response to step-change in load current (50%75%-50% of Iout(max); dI/dt = 0.1A/µ s). Load cap: 10µ F, 100 mW ESR tantalum cap and 1µ F ceramic cap. Ch 1: Vout (100mV/div), Ch 2: Iout (10A/div).
Figure 12: Output voltage response to step-change in load current (50%75%-50% of Iout(max): dI/dt = 5A/µ s). Load cap: 470µ F, 30 mW ESR tantalum cap and 1µ F ceramic cap. Ch 1: Vout (100mV/div), Ch 2: Iout (10A/div).
Product # PQ60015EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 6
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
See Fig. 15
10 µH
See Fig. 14
source
impedance
See Fig. 16
iS
VSOURCE
iC
DC/DC
Converter
VOUT
10 µF,
1 µF
47 µF,
<1W ESR
ceramic 100mW ESR
capacitor
tantalum
capacitor
electrolytic
capacitor
Figure 13: Test set-up diagram showing measurement points for Input
Terminal Ripple Current (Figure 14), Input Reflected Ripple Current
(Figure 15) and Output Voltage Ripple (Figure 16).
Figure 14: Input Terminal Ripple Current, ic, at full rated output current and nominal input voltage with 10µ H source impedance and 47µ F
electrolytic capacitor (200 mA/div). See Figure 13.
Figure 15: Input Reflected Ripple Current, is, through a 10 µ H source
inductor at nominal input voltage and rated load current (5 mA/div).
See Figure 13.
Figure 16: Output Voltage Ripple at nominal input voltage and rated
load current (50 mV/div). Load capacitance: 1µ F ceramic capacitor
and 10µ F tantalum capacitor. Bandwidth: 20 MHz. See Figure 13.
Output Voltage (V)
2.0
1.5
1.0
35 V
0.5
48 V
75 V
0.0
0
5
10
15
20
25
30
Load Current (A)
Figure 17: Output voltage vs. load current showing typical current limit
curves and converter shutdown points.
Product # PQ60015EGL25
Phone 1-888-567-9596
Figure 18: Load current (20A/div) as a function of time when the converter attempts to turn on into a 10 mW short circuit. Top trace
(2.0ms/div) is an expansion of the on-time portion of the bottom trace.
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 7
Input:
Output:
Current:
Package:
Technical Specification
0.1
35-75 V
1.5 V
25 A
Eighth-brick
0
Forward Transmission (dB)
Output Impedance (ohms)
-10
0.01
35 Vin
48 Vin
75 Vin
0.001
-20
-30
-40
35 Vin
48 Vin
75 Vin
-50
-60
-70
-80
-90
-100
-110
0.0001
10
100
1,000
10,000
10
100,000
100
1,000
10,000
100,000
Hz
Hz
Figure 19: Magnitude of incremental output impedance (Zout =
vout/iout) for minimum, nominal, and maximum input voltage at full
rated power.
Figure 20: Magnitude of incremental forward transmission (FT =
vout/vin) for minimum, nominal, and maximum input voltage at full
rated power.
1000
10
Input Impedance (ohms)
Reverse Transmission (dB)
0
-10
-20
35 Vin
48 Vin
-30
75 Vin
-40
100
35 Vin
48 Vin
10
75 Vin
1
-50
-60
10
100
1,000
10,000
0.1
100,000
10
Hz
Figure 21: Magnitude of incremental reverse transmission (RT =
iin/iout) for minimum, nominal, and maximum input voltage at full rated
power.
Product # PQ60015EGL25
Phone 1-888-567-9596
100
1,000
Hz
10,000
100,000
Figure 22: Magnitude of incremental input impedance (Zin = vin/iin)
for minimum, nominal, and maximum input voltage at full rated power.
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 8
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
BASIC OPERATION AND FEATURES
CONTROL FEATURES
The PowerQor series converter uses a two-stage power conversion topology. The first stage is a buck-converter that keeps the
output voltage constant over variations in line, load, and temperature. The second stage uses a transformer to provide the functions of input/output isolation and voltage step-down to achieve
the low output voltage required.
REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits
the user to control when the converter is on or off. This input is
referenced to the return terminal of the input bus, Vin(-). There are
two versions of the converter that differ by the sense of the logic
used for the ON/OFF input.
Both the first stage and the second stage switch at a fixed frequency for predictable EMI performance. Rectification of the
transformer’s output is accomplished with synchronous rectifiers.
These devices, which are MOSFETs with a very low on-state resistance, dissipate far less energy than Schottky diodes. This is the
primary reason that the PowerQor converter has such high efficiency, even at very low output voltages and very high output currents.
Dissipation throughout the converter is so low that it does not
require a heatsink for operation. Since a heatsink is not required,
the PowerQor converter does not need a metal baseplate or potting material to help conduct the dissipated energy to the
heatsink. The PowerQor converter can thus be built more simply
and reliably using high yield surface mount techniques on a PCB
substrate.
The PowerQor series of eighth-brick, quarter-brick and half-brick
converters uses the industry standard footprint and pin-out configuration.
In the positive logic version, the ON/OFF input is active high
(meaning that a high turns the converter on). In the negative logic
version, the ON/OFF signal is active low (meaning that a low
turns the converter on). Figure A details five possible circuits for
driving the ON/OFF pin. Figure B is a detailed look of the internal ON/OFF circuitry.
REMOTE SENSE(+) (Pins 7 and 5): The SENSE(+) inputs correct for voltage drops along the conductors that connect the converter’s output pins to the load.
Pin 7 should be connected to Vout(+) and Pin 5 should be connected to Vout(-) at the point on the board where regulation is
desired. A remote connection at the load can adjust for a voltage
drop only as large as that specified in this datasheet, that is
[Vout(+) - Vout(-)] – [Vsense(+) - Vsense(-)] <
Sense Range % x Vout
Pins 7 and 5 must be connected for proper regulation of the output voltage. If these connections are not made, the converter will
deliver an output voltage that is slightly higher than its specified
value. The converter has 100W internal resistors connected
between the output and sense pins (see diagram below).
Note: The output over-voltage protection circuit senses the voltVout(+)
ON/OFF
ON/OFF
ON/OFF
100
Vsense(+)
Vsense(_)
100
Remote Enable Circuit
Negative Logic
(Permanently Enabled)
ON/OFF
Positive Logic
(Permanently Enabled)
5V
274k
ON/OFF
50k
ON/OFF
Vin(_)
Vin(_)
TTL
100pF
50k
Vin(_)
Direct Logic Drive
Figure A: Various circuits for driving the ON/OFF pin.
Product # PQ60015EGL25
Vin(+)
5V
TTL/
CMOS
Open Collector Enable Circuit
Vout(_)
Vin(_)
Vin(_)
Vin(_)
Phone 1-888-567-9596
www.synqor.com
Figure B: Internal ON/OFF pin circuitry
Doc.# 005-2EG651D Rev. B
1/22/08
Page 9
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
age across the output (pins 8 and 4) to determine when it should
trigger, not the voltage across the converter’s sense leads (pins 7
and 5). Therefore, the resistive drop on the board should be
small enough so that output OVP does not trigger, even during
load transients.
output voltage too high may cause the over-voltage protection circuit to engage, particularly during transients.
OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits the
user to adjust the output voltage across the sense leads up or
down according to the trim range specifications.
Total DC Variation of Vout: For the converter to meet its full
specifications, the maximum variation of the DC value of Vout,
due to both trimming and remote load voltage drops, should not
be greater than that specified for the output voltage trim range.
To decrease the output voltage, the user should connect a resistor
between Pin 6 and Pin 5 (SENSE(-) input). For a desired decrease
of the nominal output voltage, the value of the resistor should be
Rtrim-down =
- 10.22
(511
D%)
(kW)
where
D% =
Vnominal – Vdesired
Vnominal
x 100%
To increase the output voltage, the user should connect a resistor
between Pin 6 and Pin 7 (SENSE(+) input). For a desired increase
of the nominal output voltage, the value of the resistor should be
Rtrim-up =
(
5.11VOUT(100+D%) _ 511 _
10.22
1.225D%
D%
)
(kW)
where
VOUT = Nominal Output Voltage
Figure C graphs the relationship between the trim resistor value
and Rtrim-up and Rtrim-down, showing the total range the output
voltage can be trimmed up or down.
Trim Resistance (kOhms)
10,000
It is not necessary for the user to add capacitance at the Trim pin.
The node is internally bypassed to eliminate noise.
PROTECTION FEATURES
Input Under-Voltage Lockout: The converter is designed to
turn off when the input voltage is too low, helping avoid an input
system instability problem, described in more detail in the application note titled “Input System Instability” available on the
SynQor website. The lockout circuitry is a comparator with DC
hysteresis. When the input voltage is rising, it must exceed the typical Turn-On Voltage Threshold value (listed on the specification
page) before the converter will turn on. Once the converter is on,
the input voltage must fall below the typical Turn-Off Voltage
Threshold value before the converter will turn off.
Output Current Limit: The maximum current limit remains constant as the output voltage drops. However, once the impedance
of the short across the output is small enough to make the output
voltage drop below the specified Output DC Current-Limit
Shutdown Voltage, the converter turns off.
The converter then enters a “hiccup mode” where it repeatedly
turns on and off at a 5 Hz (nominal) frequency with a 5% duty
cycle until the short circuit condition is removed. This prevents
excessive heating of the converter or the load board.
Output Over-Voltage Limit: If the voltage across the output
pins exceeds the Output Over-Voltage Protection threshold, the
converter will immediately stop switching. This prevents damage
to the load circuit due to 1) excessive series resistance in output
current path from converter output pins to sense point, 2) a
release of a short-circuit condition, or 3) a release of a current
limit condition. Load capacitance determines exactly how high
the output voltage will rise in response to these conditions. After
200 ms the converter will automatically restart.
1,000
100
10
1
0
2
4
6
8
10
% increase Vout
12
14
16
18
20
% decrease Vout
Figure C: Trim Graph for 1.5Vout module
Note: the TRIM feature does not affect the voltage at which the
output over-voltage protection circuit is triggered. Trimming the
Product # PQ60015EGL25
Phone 1-888-567-9596
Over-Temperature Shutdown: A temperature sensor on the
converter senses the average temperature of the module. The thermal shutdown circuit is designed to turn the converter off when the
temperature at the sensed location reaches the Over-Temperature
Shutdown value. It will allow the converter to turn on again when
the temperature of the sensed location falls by the amount of the
Over-Temperature Shutdown Restart Hysteresis value.
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 10
Input:
Output:
Current:
Package:
Technical Specification
APPLICATION CONSIDERATIONS
Input System Instability: This condition can occur because
any DC/DC converter appears incrementally as a negative
resistance load. A detailed application note titled “Input
System Instability” is available on the SynQor website which
provides an understanding of why this instability arises, and
shows the preferred solution for correcting it.
35-75 V
1.5 V
25 A
Eighth-brick
itance is specified in the “Input Characteristics” section. More
detailed information is available in the application note titled
“EMI Characteristics” on the SynQor website.
Application Circuits: Figure D provides a typical circuit diagram which details the input filtering and voltage trimming.
Input Filtering and External Capacitance: Figure E provides a diagram showing the internal input filter components.
This filter dramatically reduces input terminal ripple current,
which otherwise could exceed the rating of an external electrolytic input capacitor. The recommended external input capac-
Vin(+)
Vin
External
Input
Filter
Electrolytic
Capacitor
47µF
Vout(+)
Vsense(+)
ON/OFF
Trim
Vsense(_)
Vin(_)
Rtrim-up
or
Rtrim-down
Cload
Iload
Vout(_)
Figure D: Typical application circuit (negative logic unit, permanently enabled).
L
Vin(+)
C
Vin(_)
Figure E: Internal Input Filter Diagram (component values listed on the specifications page).
Product # PQ60015EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 11
Input:
Output:
Current:
Package:
Technical Specification
Startup Inhibit Period: The Startup Inhibit Period ensures that
the converter will remain off for approximately 200ms when it is
shut down for any reason. When an output short is present, this
generates a 5Hz "hiccup mode," which prevents the converter
from overheating. In all, there are seven ways that the converter
can be shut down, initiating a Startup Inhibit Period:
35-75 V
1.5 V
25 A
Eighth-brick
When the input voltage rises above the UVL threshold, the Input
Under-Voltage Lockout is released, and a Startup Inhibit Period is
initiated. At the end of this delay, the ON/OFF pin is evaluated,
and since it is active, the unit turns on.
At time t1, the unit is disabled by the ON/OFF pin, and it cannot
be enabled again until the Startup Inhibit Period has elapsed.
• Input Under-Voltage Lockout
When the ON/OFF pin goes high after t2, the Startup Inhibit
Period has elapsed, and the output turns on within the typical
Turn-On Time.
• Input Over-Voltage Shutdown (not present in Eighth-brick)
• Output Over-Voltage Protection
• Over Temperature Shutdown
• Current Limit
• Short Circuit Protection
• Turned off by the ON/OFF input
Figure F shows three turn-on scenarios, where a Startup Inhibit
Period is initiated at t0, t1, and t2:
Before time t0, when the input voltage is below the UVL threshold,
the unit is disabled by the Input Under-Voltage Lockout feature.
RoHS Compliance: The EU led RoHS (Restriction of Hazardous
Substances) Directive bans the use of Lead, Cadmium,
Hexavalent Chromium, Mercury, Polybrominated Biphenyls
(PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical
and Electronic Equipment. This SynQor product is available as
5/6 RoHS compliant (product with lead) or 6/6 RoHS compliant.
For more information please refer to SynQor’s RoHS addendum
available at our RoHS Compliance / Lead Free Initiative web
page or e-mail us at [email protected]
Vin
Under-Voltage
Lockout Turn-On
Threshold
ON/OFF
(pos logic)
ON
OFF
OFF ON
ON
9ms (typical
turn on time)
Vout
200ms
(typical start-up
inhibit period)
t1
t0
200ms
200ms
t
t2
Figure F: Startup Inhibit Period (turn-on time not to scale)
Product # PQ60015EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 12
Input:
Output:
Current:
Package:
Technical Specification
35-75 V
1.5 V
25 A
Eighth-brick
PART NUMBERING SYSTEM
ORDERING INFORMATION
The part numbering system for SynQor’s PowerQor DC/DC
converters follows the format shown in the example below.
The tables below show the valid model numbers and ordering
options for converters in this product family. When ordering
SynQor converters, please ensure that you use the complete
15 character part number consisting of the 12 character base
part number and the additional 3 characters for options. To
order 6/6 RoHS compliant product please add a “-G” suffix.
PQ 60 015 E G L 25 N N S
Options
(see
Ordering Information)
Output Current
Thermal Design/Profile
Performance Level
Package Size
Output Voltage
Input Voltage
Product Family
The first 12 characters comprise the base part number and the
last 3 characters indicate available options. Although there
are no default values for enable logic and pin length, the most
common options are negative logic and 0.145” pins. These
part numbers are more likely to be readily available in stock
for evaluation and prototype quantities. A “-G” suffix indicates 6/6 RoHS compliance.
Application Notes
A variety of application notes and technical white papers can
be downloaded in pdf format from our website.
PATENTS (additional patent applications may be filed)
SynQor holds the following patents, one or more of which
might apply to this product:
5,999,417
6,594,159
6,927,987
7,119,524
6,222,742
6,731,520
7,050,309
7,269,034
6,545,890
6,894,468
7,072,190
7,272,021
6,577,109
6,896,526
7,085,146
7,272,023
Model Number
Input Voltage
PQ60010EGw 20xyz
PQ60010EGw 25xyz
PQ60012EGw 20xyz
PQ60012EGw 25xyz
PQ60015EGw 20xy S
PQ60015EGw 25xy S
PQ60018EGw 20xy S
PQ60018EGw 25xy S
PQ60025EGw 20xy S
PQ60025EGw 25xy S
PQ60033EGw 20xy S
PQ60050EGw15xy S
PQ60120EGw 07xy S
PQ60150EGw 05xy S
PQ60240EGw 03xy S
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
35 - 75 V
Output Max Output
Voltage
Current
1.0 V
20 A
1.0 V
25 A
1.2 V
20 A
1.2 V
25 A
1.5 V
20 A
1.5 V
25 A
1.8 V
20 A
1.8 V
25 A
2.5 V
20 A
2.5 V
25 A
3.3 V
20 A
5.0 V
15 A
12 V
6.25 A
15 V
5A
24 V
3A
Modules above can be ordered with an increased bottom side
board clearance and a slightly larger total height (see page 2
for dimensions). To order replace EGL in the part number with
EGA. There are no other differences from the EGL units.
The following option choices must be included in place of the
w x y z spaces in the model numbers listed above.
Options Description: w x y z
Thermal
Design
Enable
Logic
Pin
Length
K - 0.110"
A - Open Frame
P - Positive N - 0.145"
L - Low Profile Open Frame N - Negative R - 0.180"
Y - 0.250"
Feature
Set
S - Standard
Contact SynQor for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # PQ60015EGL25
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
Warranty
SynQor offers a three (3) year limited warranty. Complete warranty
information is listed on our website or is available upon request from
SynQor.
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
www.synqor.com
Doc.# 005-2EG651D Rev. B
1/22/08
Page 13
Similar pages