AP9214L

AP9214L
SINGLE CHIP SOLUTION FOR 1-CELL Li+ BATTERY PACK
Description
Pin Assignments
The AP9214L is a single chip protection solution specially designed
for 1-cell Li+ rechargeable battery pack application.
(Top View)
NEW PRODUCT
The AP9214L includes a 1-cell Lion battery protection chip and dual
N-CH, ultra low RSS(ON) MOSFET with common drain.
High Voltage CMOS Process, up to 30V (VDD to VM)
Low Quiescent Current (+25°C )

In Normal Mode, 3.0µA (Typ.), 4.5µA (Max.), VDD = 3.5V

In Power-Down Mode, 0.1µA (Max.)
High-Accuracy Voltage Detection Circuit (+25°C)

Overcharge Detection Voltage: 3.5V to 4.5V (5mV Steps)
Accuracy ±25mV

Overcharge Hysteresis Voltage Range: 0.1V to 0.4V (50mV
Steps) Accuracy ±50mV

Overdischarge Detection Voltage: 2.0V to 3.4V (10mV
Steps) Accuracy ±35mV

Overdischarge Hysteresis Voltage Range: 0V to 0.7V (40mV
Steps) Accuracy ±65mV

Discharge Overcurrent Detection Voltage: 0.05V to 0.32V
(10mV Steps) Accuracy ±15mV

Short Current Detection Voltage: 0.45V to 0.7V (50mV
Steps) Accuracy ±100mV

Charge Overcurrent Detection Voltage: -0.2V to -0.05V
(10mV Steps) Accuracy ±15mV

Overcharger Detection Voltage: 8.0V (Fixed) Accuracy ±2V



VDD
S2
2
5
NC
3
4
VM
S1
1
VSS
VDD
6
S2
2
5
VM
3
4
NC
EP
Features




VSS
6
U-DFN2535-6 (Option 1)
The AP9214L is available in U-DFN2535-6 package with two kinds of
pin options.

1
EP
The AP9214L provides rich battery protection features and can turnoff the N-CH MOSFET by detecting overcharge voltage/current, over
discharge voltage/current, or load short circuit. The AP9214L has
built-in fixed delay time to save external components.


S1
U-DFN2535-6 (Option 2)
Applications

Li+ Rechargeable Battery Pack
Overcharger Release Voltage: 7.3V (Fixed) Accuracy ±2V
Built-in Fixed Detection Delay Time (+25°C ), Accuracy ±20%
Power-Down Mode Selectable (Yes or No)
0V Battery Charge Selectable (Permission or Inhibition)
Overcharge Protection Mode Selectable (Auto Release or
Latch)
Totally Lead-free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
AP9214L
Document number: DS38413 Rev. 1 - 2
1 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Typical Applications Circuit (Note 4)
P+
R1
330Ω to 470Ω
3(3)
NEW PRODUCT
BAT
VDD
C1
100n
2(2)
VSS
U1
AP9214L
(U-DFN2535-6)
S1
1(1)
VM
4(5)
R2
2.7kΩ
S2
P-
6(6)
A (B)
A for Pin-out Option 1
B for Pin-out Option 2
4. R1 and C1 are used to stabilize the supply voltage of the AP9214L. The recommended range of R1 value is 330Ω to 470Ω and C1 value is 10nF to
1000nF, typical value is 100nF. R2 should be connected between P- to VM sense terminal to monitor the status of charger and the charge/discharge
current. The R2 should be between 300Ω and 4kΩ, typical value is 2.7kΩ. R1 and R2 are also used as current limit resistors if the battery or charger is
connected reversely. Polarity reversing may cause the power consumption of R1 and R2 to go over their power dissipation rating, therefore R1 and R2
values should be selected appropriately for the actual application. If R2 is more than 4kΩ resistor, charge may not be off due to the voltage drop on R2.
Note:
For power-down mode, when first connecting AP9214L system board to the battery, it is necessary to use charger or to short P- to the battery negative
polarity. Once the AP9214L is activated, the charger or connection can be removed, otherwise the battery cannot discharge current through system
board.
The values selected should follow the recommended typical range mentioned above. It has not been confirmed whether the operation is normal or not in
circuits other than the above example of connection. In addition, the example of connection shown above and the typical value do not exactly guarantee
proper operation. Please perform the actual application to set the suitable value through your complete evaluation.
Pin Descriptions
Pin Number
Pin Number
Option 1
Option 2
1
1
S1
2
2
VSS
Negative power supply pin.
3
3
VDD
Positive power supply pin, connecting this pin to battery positive pole through R1.
4
5
VM
Charger negative input pin, short this pin to S2 pin through R2.
5
4
NC
Not connected, leave this pin floating.
6
6
S2
Source pin of charging MOSFET, connecting this pin to charge negative input.
EP
EP
Drain
AP9214L
Document number: DS38413 Rev. 1 - 2
Pin Name
Function
Source pin of discharging MOSFET, connecting this pin to battery negative pole.
Thermal PAD is common drain of charge and discharge MOSFET, so in PCB layout, prefer to
use large copper area to cover this pad for better thermal dissipation, then leave it open.
2 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Functional Block Diagram
0V
Charge
Option
NEW PRODUCT
Logic Circuit
3 (3)
VDD
Level Shift
Delay Time
Circuit
VM
2 (2)
4 (5)
VSS
RVMD
Logic Circuit
RVMS
G1
1(1)
S1
G2
D1
D2
S1
S2
6(6)
S2
EP
Drain
A (B)
A for Pin-out Option 1
B for Pin-out Option 2
AP9214L
Document number: DS38413 Rev. 1 - 2
3 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Absolute Maximum Ratings (Notes 5 & 6)
Symbol
VDS
NEW PRODUCT
VDM
Parameter
Ratings
Supply Voltage (Between VDD and VSS)
Charge Input Voltage
(Between VDD and VM for Protection Chip)
Unit
-0.3 to 12
V
-0.3 to 24
V
VDSS
MOSFET Drain-to-Source Voltage
24
V
VGSS
MOSFET Gate-to-Source Voltage
±12
V
Continuous Drain Current, VGS = 4.5V, TA = +25°C
9.0
A
ID
Continuous Drain Current, VGS = 4.5V, TA = +70°C
PD
Power Dissipation
TJ
Maximum Junction Temperature
TSTG
Notes:
Storage Temperature Range
7.1
A
1000
mW
+150
°C
-65 to +150
°C
5. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional
operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
6. Ratings apply to ambient temperature at +25°C. The JEDEC High-K board design used to derive this data was a 2 inch x 2 inch multilayer board with 2ounce internal power and ground planes and 2-ounce copper traces on the top and bottom of the board.
Recommended Operating Conditions
Symbol
Parameter
Min
Max
Unit
VDS
Supply Voltage (Between VDD and VSS)
1.5
5.5
V
VDM
Charge Input Voltage (Between VDD and VM)
-0.3
5.5
V
Operating Ambient Temperature
-40
+85
ºC
TA
AP9214L
Document number: DS38413 Rev. 1 - 2
4 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Electrical Characteristics (TA = +25oC, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified.)
Symbol
Parameter
VCU
Overcharge Detection Voltage
VCL
Overcharge Release Voltage
Conditions
－
VCL ≠ VCU
NEW PRODUCT
VCL = VCU
VDL
Overdischarge Detection Voltage
VDU
Overdischarge Release Voltage
－
VDU ≠ VDL
VDU = VDL
Min
VCU
- 0.025
VCL
- 0.050
VCL
- 0.025
VDL
- 0.035
VDU
- 0.100
VDU
- 0.035
VDOC
-0.015
VSHORT
-0.10
VCOC
-0.015
Typ
VCU
VCL
VCL
VDL
VDU
VDU
Max
VCU
+ 0.025
VCL
+ 0.050
VCL
+ 0.025
VDL
+ 0.035
VDU
+ 0.100
VDU
+ 0.035
VDOC
+0.015
VSHORT
+0.10
VCOC
+0.015
Units
V
V
V
V
V
V
Discharge Overcurrent Detection Voltage
－
VSHORT
Load Short-Circuiting Detection Voltage
－
VCOC
Charge Overcurrent Detection Voltage
－
ICC
Current Consumption During Operation
VDD = 3.5V, VM = 0V
1.5
3.0
4.5
μA
－
－
0.1
μA
Current Consumption at Power Down
VDD = 1.8V Power Down Mode
VM Pin
Without Power Down
Floating
Mode (Auto Wake up)
－
－
5.5
μA
VDOC
ISTB
VDOC
VSHORT
VCOC
V
V
V
RVMD
Resistance Between VM Pin and VDD Pin
VDD = 1.8V, VM = 0V
150
300
500
kΩ
RVMS
Resistance Between VM Pin and VSS Pin
VDD = 3.5V, VM = 1.0V
10
30
50
kΩ
V0CHA
0V Battery Charge Starting Charge Voltage
0V Battery Charging “Available”
1.2
－
－
V
V0INH
0V Battery Charge Inhibition Battery Voltage 0V Battery Charging “Unavailable”
－
－
0.45
V
VOVCHG
Overvoltage Charge Detection Voltage
VDD = 3.5V
6.0
8.0
10.0
V
VOVCHGR
Overvoltage Charge Release Voltage
VDD = 3.5V
5.3
7.3
9.3
V
tCU
Overcharge Detection Delay Time
－
tCU * 0.8
tCU
tCU * 1.2
ms
tCUR
Overcharge Release Delay Time
－
tCUR * 0.8
tCUR
tCUR * 1.2
ms
tDL
Overdischarge Detection Delay Time
－
tDL * 0.8
tDL
tDL * 1.2
ms
tDLR
Overdischarge Release Delay Time
－
tDLR * 0.8
tDLR
tDLR * 1.2
ms
tDOC
Discharge Overcurrent Detection Delay Time －
tDOC * 0.8
tDOC
tDOC * 1.2
ms
tDOCR
Discharge Overcurrent Release Delay Time
－
tDOCR * 0.8
tDOCR
tDOCR * 1.2
ms
tSHORT
Load Short Detection Delay Time
－
tSHORT * 0.8
tSHORT
tSHORT * 1.2
μs
tCOC
Charge Overcurrent Detection Delay Time
－
tCOC * 0.8
tCOC
tCOC * 1.2
ms
tCOCR
Charge Overcurrent Release Delay Time
－
tCOCR * 0.8
tCOCR
tCOCR * 1.2
ms
AP9214L
Document number: DS38413 Rev. 1 - 2
5 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Electrical Characteristics (Cont.)
(TA = -40oC to +85oC, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified.)
Symbol
Parameter
VCU
Overcharge Detection Voltage
VCL
Overcharge Release Voltage
Conditions
－
VCL ≠ VCU
NEW PRODUCT
VCL = VCU
VDL
Overdischarge Detection Voltage
VDU
Overdischarge Release Voltage
－
VDU ≠ VDL
VDU = VDL
Min
VCU
- 0.060
VCL
- 0.080
VCL
- 0.060
VDL
- 0.080
VDU
- 0.150
VDU
- 0.080
VDOC
-0.021
VSHORT
-0.34
VCOC
-0.040
Typ
VCU
VCL
VCL
VDL
VDU
VDU
Max
VCU
+ 0.040
VCL
+ 0.065
VCL
+ 0.040
VDL
+ 0.080
VDU
+ 0.190
VDU
+ 0.080
VDOC
+0.024
VSHORT
+0.34
VCOC
+0.040
Units
V
V
V
V
V
V
Discharge Overcurrent Detection Voltage
－
Load Short Detection Voltage
－
VCOC
Charge Overcurrent Detection Voltage
－
ICC
Current Consumption During Operation
VDD = 3.5V,VM = 0V
1.0
3.0
7.0
μA
－
－
1.0
μA
Current Consumption at Power Down
Power Down Mode
VDD =1.8V
Without Power
VM Pin
Down Mode (Auto
Floating
Wake up)
－
－
8
μA
100
300
650
kΩ
5
30
65
kΩ
1.2
－
－
V
－
－
0.3
V
VDOC
VSHORT
ISTB
RVMD
Resistance Between VM Pin and VDD Pin
VDD = 1.8V, VM = 0V
RVMS
Resistance Between VM Pin and VSS Pin
VDD = 3.5V, VM = 1.0V
V0CHA
V0INH
0V Battery Charging
0V Battery Charge Starting Charge Voltage
“Available”
0V Battery Charging
0V Battery Charge Inhibition Battery Voltage
“Unavailable”
VDOC
VSHORT
VCOC
V
V
V
VOVCHG
Overvoltage Charge Detection Voltage
VDD = 3.5V
5.5
8.0
10.5
V
VOVCHGR
Overvoltage Charge Release Voltage
VDD = 3.5V
5.0
7.3
9.5
V
tCU
Overcharge Detection Delay Time
－
tCU * 0.6
tCU
tCU * 1.4
ms
tCUR
Overcharge Release Delay Time
－
tCUR * 0.6
tCUR
tCUR * 1.4
ms
tDL
Overdischarge Detection Delay Time
－
tDL * 0.6
tDL
tDL * 1.4
ms
tDLR
Overdischarge Release Delay Time
－
tDLR * 0.6
tDLR
tDLR * 1.4
ms
tDOC
Discharge Overcurrent Detection Delay Time －
tDOC * 0.6
tDOC
tDOC * 1.4
ms
tDOCR
Discharge Overcurrent Release Delay Time －
tDOCR * 0.6
tDOCR
tDOCR * 1.4
ms
tSHORT
Load Short Detection Delay Time
－
tSHORT * 0.6
tSHORT
tSHORT * 1.4
μs
tCOC
Charge Overcurrent Detection Delay Time
－
tCOC * 0.6
tCOC
tCOC * 1.4
ms
tCOCR
Charge Overcurrent Release Delay Time
－
tCOCR * 0.6
tCOCR
tCOCR * 1.4
ms
AP9214L
Document number: DS38413 Rev. 1 - 2
6 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Electrical Characteristics (Cont., Notes 7, 8)
(TA = +25oC, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified.)
Symbol
NEW PRODUCT
Conditions
Min
Typ
Max
Units
Zero Gate Voltage Drain Current
VDS = 20V, VGS = 0
－
－
1.0
μA
RSS(ON)1
Static Source-Source On-Resistance 1
VDD = 4.0V, ID = 1.0A
10
13
16
mΩ
RSS(ON)2
Static Source-Source On-Resistance 2
VDD = 3.9V, ID = 1.0A
10
13.5
16.5
mΩ
RSS(ON)3
Static Source-Source On-Resistance 3
VDD = 3.0V, ID = 1.0A
11
14
17
mΩ
Diode Forward Voltage
VGS = 0V, IS = 1A
－
0.75
1.0
V
IDSS
VSD
Notes:
Parameter
7. In case of Gate-Source voltage of charging MOSFET is 0V. In case of Gate-Source voltage of discharging MOSFET is 0V.
8. These specifications are guaranteed by design - will not be tested in production.
AP9214L
Document number: DS38413 Rev. 1 - 2
7 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Application Information
Operation Mode
1. Normal Status
NEW PRODUCT
The AP9214L monitors the battery voltage between the VDD pin and VSS pin as well as the voltage difference between the VM pin and VSS pin
to control battery charging and discharging. When the battery voltage is between overdischarge detection voltage (V DL) and overcharge detection
voltage (VCU) as well as the VM pin voltage is between the charge overcurrent detection voltage (VCOC) and discharge overcurrent detection
voltage (VDOC), the AP9214L will turn on discharging and charging MOSFET. In these conditions, the battery can charge and discharge freely.
Also, RVMD does not connect to VDD pin and RVMS does not connect to VSS pin in this status.
2. Overcharge Status
If the battery voltage is more than VCU during charging status for the overcharge detection delay time (t CU) or longer, the AP9214L turns off the
charging MOSFET to stop charging. RVMD and RVMS are not connected in overcharge status.
When VM pin voltage is lower than VDOC and battery voltage falls below VCL, the AP9214L will release from overcharge status.
When VM pin voltage is equal or more than VDOC and battery voltage falls below VCU, the AP9214L will release from overcharge status.
3. Overdischarge Status
If the battery voltage is less than VDL during discharging status for the overdischarge detection delay time (tDL) or longer, the AP9214L turns off the
discharging MOSFET to stop discharging. In overdischarge status, RVMD is connected to VDD and VM pin voltage is pulled up to VDD by RVMD,
but RVMS is not connected.
For power-down mode version, the AP9214L recovers normal status from overdischarge status only by charging the battery through the charger.
When VM pin voltage to VSS pin voltage is less than typical -0.7V and the battery voltage rises over VDL, the AP9214L will release from
overdischarge status. If VM pin voltage to VSS pin voltage is higher than typical -0.7V, the AP9214L will release from overdischarge status until
the battery voltage rises over VDU.
For auto-wake-up version AP9214LA, the device recovers to normal status from overdischarge status if either of these two conditions are satisfied:
If charger is connected: the AP9214LA overdischarge status is released in the same way as described above in AP9214L overdischarge Status section.
If no charger is connected:
1) The battery voltage reaches the overdischarge release voltage (VDU) or higher;
2) Maintains continuous time more than overdischarge release delay time tDLR.
4. Discharge Overcurrent and Short Current Status
When battery is in discharge overcurrent status, if the voltage of the VM pin to VSS pin is equal or more than VDOC to VSHORT and detection lasts
for the discharge overcurrent detection delay time (tDOC) or longer, the AP9214L turns off the discharging MOSFET to stop discharging.
When the battery is in short current status, if the voltage of the VM pin to VSS pin is equal to or more than VSHORT, and the detection lasts for the
short current detection delay time or longer, the AP9214L turns off the discharge MOSFET to stop discharging.
In discharge overcurrent or short current status, RVMS is connected to VSS but RVMD is not connected. The voltage of VM pin is almost equal to
VDD as long as the load is connected. When the load is disconnected, the voltage of VM pin will become almost equal to VSS (due to RVMS being
connected) and then the AP9214L will release from discharge overcurrent or short current status.
5. Charge Overcurrent Status
When the battery is in charge overcurrent status, if the voltage of the VM pin to VSS pin is equal to or less than VCOC and the detection continues
for the charge overcurrent detection delay time (tCOC) or longer, the AP9214L turns off the charging MOSFET to stop charging.
6. 0V Battery Charging Function (Optional)
This function is available as an option and can be factory set internally. The AP9214L has this function built in.
0V charging function permits charger to recharge the battery whose voltage is 0V due to self-discharge. If 0V charging function is not present, the
device will prevent charger to recharge the battery whose voltage is 0V due to self-discharge. (If a device without 0V charging function is needed,
please contact Diodes sales team.)
AP9214L
Document number: DS38413 Rev. 1 - 2
8 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Application Information (Cont.)
7. Overvoltage Charger Detection Circuit
This function is used to monitor the charger voltage between the VDD pin and VM pin, and when this voltage exceeds overvoltage charger
detection voltage (8.0V Typ.), the AP9214L will turn off charging MOSFET, when this voltage drops below overvoltage charger release voltage
(7.3V Typ.), it then turns on charging MOSFET. There is no delay time setting for detection and release.
NEW PRODUCT
8. Power-Down Mode or Auto-Wake-Up Function (Optional)
In device with power-down function, during power-down mode, device enters the overdischarge status. The IC enters sleep mode and the current
consumption becomes very low, typically 0.1μA. To release from power-down status to the normal status, charger connection is required.
In device with auto-wakeup mode, the IC remains active in the overdischarge state. The IC is released into the normal state by the operation that
increases the battery voltage more than overdischarge release voltage.
AP9214L
Document number: DS38413 Rev. 1 - 2
9 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Application Information (Timing Chart)
1.
Overcharge and Overdischarge Detection
VCU
VCL
NEW PRODUCT
VDD
VDU
VDL
VSS
VDD
DO
VSS
VDD
Red line is for
no shutdown
mode version
CO
VVM
VDD
VM
VDOC
VSS
VCOC
VP2
S1
1
3
S2
2
4
S1
P1
Document number: DS38413 Rev. 1 - 2
1
3
P1
1: tDL
2: tCU
3: tCUR
4: tDLR
AP9214L
3
S2
S1: Charger connection
S2: Load connection
P1: RVMD pull-up connection
10 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Application Information (Timing Chart) (Cont.)
2.
Discharge Overcurrent Detection
VCU
NEW PRODUCT
VCL
VDD
VDU
VDL
VSS
ON
DO
OFF
ON
CO
OFF
VDD
VSHORT
VM
VDOC
VSS
1
1
3
S1
P1
1: tDOC
2: tSHORT
3: tDOCR
AP9214L
Document number: DS38413 Rev. 1 - 2
2
3
S2
P1
S1: Connect over current load
S2: Connect short current load
P1: RVMS pull-down connection
11 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Application Information (Timing Chart) (Cont.)
3.
Charge Overcurrent Detection
VCU
VCL
VDD
NEW PRODUCT
VDU
VDL
VSS
VDD
DO
VSS
VDD
CO
VVM
VDD
VM
VSS
VCOC
VP1
2
S1
1: tCOC
2: tCOCR
AP9214L
Document number: DS38413 Rev. 1 - 2
S1: Connect over current charger
12 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Ordering Information (Note 9)
AP9214L X - X - X - X
Power Down Mode
Product Name
Package
Packing
HSB: U-DFN2535-6
7: Tape & Reel
Product Code
Voltage & Delay Time
Blank: Yes
A: No (Auto-wake-up) Combination Code
(Pin-out Option 1)
NEW PRODUCT
HSBR: U-DFN2535-6
(Pin-out Option 2)
Device
Package Code
AP9214L(X)-X-HSB-7
AP9214L(X)-X-HSBR-7
Packaging
Pin Out
HSB
HSBR
7” Tape and Reel
Quantity
Part Number Suffix
U-DFN2535-6
Option 1
3000/Tape & Reel
-7
U-DFN2535-6
Option 2
3000/Tape & Reel
-7
Voltage Combination
Part Number
Discharge
Charge
Overcharge Overcharge Overdischarge Overdischarge
Load Short
Overcurrent
Overurrent
Detection
Release
Detection
Release
Detection
Detection
Detection
Voltage
Voltage
Voltage
Voltage
Voltage
Voltage
Voltage
VCU
VCL
VDL
VDU
VSHORT
VDOC
VCOC
Over
Voltage
Charger
Detection
Voltage
Over
Voltage
Charger Powr-down Overcharge
Protection
Release
Function
Mode
Voltage
VOVCHG
VOVCHGR
Delay
Time
0V Battery
Charge
Function
AP9214L(X)AA-HSB(X)-7
4.375V
4.175V
2.500V
2.900V
0.150V
0.700V
-0.150V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AB-HSB(X)-7
4.425V
4.225V
2.500V
2.900V
0.150V
0.700V
-0.150V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AC-HSB(X)-7
4.375V
4.175V
2.500V
2.900V
0.095V
0.700V
-0.095V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AD-HSB(X)-7
4.375V
4.175V
2.500V
2.900V
0.120V
0.700V
-0.120V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AE-HSB(X)-7
4.200V
4.100V
2.500V
3.000V
0.300V
0.550V
-0.100V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AF-HSB(X)-7
4.375V
4.175V
2.500V
2.900V
0.180V
0.700V
-0.180V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AG-HSB(X)-7
4.375V
4.175V
2.500V
2.900V
0.075V
0.700V
-0.075V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AH-HSB(X)-7
4.425V
4.225V
2.500V
2.900V
0.075V
0.700V
-0.075V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AI-HSB(X)-7
4.500V
4.300V
2.400V
2.800V
0.150V
0.700V
-0.075V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AJ-HSB(X)-7
4.375V
4.175V
2.400V
2.800V
0.125V
0.700V
-0.125V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AK-HSB(X)-7
4.250V
4.050V
2.400V
3.000V
0.150V
0.700V
-0.150V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AL-HSB(X)-7
4.275V
4.175V
2.300V
2.400V
0.180V
0.700V
-0.180V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AM-HSB(X)-7
4.375V
4.175V
2.300V
2.400V
0.180V
0.700V
-0.180V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L(X)AN-HSB(X)-7
4.225V
4.025V
3.200V
3.400V
0.060V
0.450V
-0.060V
8.0V
7.3V
Selectable
Auto
Release
Option 1
Permission
AP9214L
Document number: DS38413 Rev. 1 - 2
13 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Ordering Information (Cont.) (Note 9)
Delay Time Combination
NEW PRODUCT
Part Number
AP9214L(X)-XXHSB(X)-7
Note:
Overcharge
Detection Delay
Time
Overcharge
Release
Delay Time
Overdischarge Overdischarge
Detection Delay Release Delay
Time
Time
tCU
tCUR
tDL
tDLR
1.0s
2.0ms
115ms
2.0ms
Discharge
Overcurrent
Detection
Delay Time
Discharge
Overcurrent
Release
Delay Time
Charge
Overcurrent
Detection
Delay Time
Charge
Overcurrent
Release
Delay Time
tDOC
tDOCR
tCOC
tCOCR
10.0ms
2.0ms
10.0ms
2.0ms
Load Short
Detection
Delay Time
tSHORT
320µs
9. If products of any other voltage versions are needed, please contact with the local sales’ office.
Marking Information
(Top View)
XX(XXX)
YWX
AP9214L
Document number: DS38413 Rev. 1 - 2
XX(XXX) : Identification Code (2~5 Codes)
Y : Year : 0 to 9
W : Week : A to Z : 1 to 26 week;
a to z : 27 to 52 week; z represents
52 and 53 week
X : A to Z : Internal Code
14 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
Marking Information (Cont.)
NEW PRODUCT
Part Number
AP9214LA-AA-HSB-7
AP9214LA-AB-HSB-7
AP9214LA-AC-HSB-7
AP9214LA-AD-HSB-7
AP9214LA-AE-HSB-7
AP9214LA-AF-HSB-7
AP9214LA-AG-HSB-7
AP9214LA-AH-HSB-7
AP9214LA-AI-HSB-7
AP9214LA-AJ-HSB-7
AP9214LA-AK-HSB-7
AP9214LA-AL-HSB-7
AP9214LA-AM-HSB-7
AP9214LA-AN-HSB-7
AP9214LA-AA-HSBR-7
AP9214LA-AB-HSBR-7
AP9214LA-AC-HSBR-7
AP9214LA-AD-HSBR-7
AP9214LA-AE-HSBR-7
AP9214LA-AF-HSBR-7
AP9214LA-AG-HSBR-7
AP9214LA-AH-HSBR-7
AP9214LA-AI-HSBR-7
AP9214LA-AJ-HSBR-7
AP9214LA-AK-HSBR-7
AP9214LA-AL-HSBR-7
AP9214LA-AM-HSBR-7
AP9214LA-AN-HSBR-7
AP9214L-AA-HSB-7
AP9214L-AB-HSB-7
AP9214L-AC-HSB-7
AP9214L-AD-HSB-7
AP9214L-AE-HSB-7
AP9214L-AF-HSB-7
AP9214L-AG-HSB-7
AP9214L-AH-HSB-7
AP9214L-AI-HSB-7
AP9214L-AJ-HSB-7
AP9214L-AK-HSB-7
AP9214L-AL-HSB-7
AP9214L-AM-HSB-7
AP9214L-AN-HSB-7
AP9214L-AA-HSBR-7
AP9214L-AB-HSBR-7
AP9214L-AC-HSBR-7
AP9214L-AD-HSBR-7
AP9214L-AE-HSBR-7
AP9214L-AF-HSBR-7
AP9214L-AG-HSBR-7
AP9214L-AH-HSBR-7
AP9214L-AI-HSBR-7
AP9214L-AJ-HSBR-7
AP9214L-AK-HSBR-7
AP9214L-AL-HSBR-7
AP9214L-AM-HSBR-7
AP9214L-AN-HSBR-7
AP9214L
Document number: DS38413 Rev. 1 - 2
Package
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
U-DFN2535-6
15 of 17
www.diodes.com
Identification Code
14AA
14AB
14AC
14AD
14AE
14AF
S6
S8
14AI
14AJ
14AK
14AL
14AM
14AN
14AAR
14ABR
14ACR
14ADR
14AER
14AFR
R7
RH
14AIR
14AJR
14AKR
14ALR
14AMR
14ANR
14A
14B
14C
14D
14E
14F
X8
X9
14I
14J
14K
14L
14M
14N
14AR
14BR
14CR
14DR
14ER
14FR
14GR
14HR
14IR
14JR
14KR
14LR
14MR
14NR
December 2015
© Diodes Incorporated
AP9214L
Package Outline Dimensions
Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version.
U-DFN2535-6 (Type B)
A3
A
NEW PRODUCT
Seating Plane
D
A1
e1
L(X6)
e
R0.
(P 150
in #
1 ID
)
E
E2
D2
U-DFN2535-6
(Type B)
Dim
Min
Max
Typ
A
0.50
0.60
A1
0.00
0.05 0.02
A3
0.127
b
0.25
0.35 0.30
b2
1.05
1.15 1.10
D
2.45
2.55 2.50
D2
2.01
2.21 2.11
E
3.45
3.55 3.50
E2
2.20
2.40 2.30
e
0.55
e1
0.95
L
0.25
0.35 0.30
z
0.15
All Dimensions in mm
b
z
b2
Suggested Pad Layout
Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version.
U-DFN2535-6 (Type B)
X1
X
X2
Dimensions
C
C1
X
X1
X2
Y
Y1
Y1
Y
C1
AP9214L
Document number: DS38413 Rev. 1 - 2
Value
(in mm)
0.550
0.950
0.400
1.200
2.210
0.500
2.400
C
16 of 17
www.diodes.com
December 2015
© Diodes Incorporated
AP9214L
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
NEW PRODUCT
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2015, Diodes Incorporated
www.diodes.com
AP9214L
Document number: DS38413 Rev. 1 - 2
17 of 17
www.diodes.com
December 2015
© Diodes Incorporated