Si53115

S i 5 3 115
15-O UTPUT PCI E G EN 3 BUFFER / Z ERO D ELAY B UFFER
Features








Ordering Information:
See page 30.
Pin Assignments
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
GND
Applications
GND
VDD_IO
DIF_10
DIF_10


Separate VDDIO for outputs
PLL or bypass mode
Spread spectrum tolerable
1.05 to 3.3 V I/O supply voltage
50 ps output-to-output skew
50 ps cyc-cyc jitter (PLL mode)
Low phase jitter (Intel QPI, PCIe
Gen 1/2/3/4 common clock
compliant)
Gen 3 SRNS Compliant
100 ps input-to-output delay
Extended Temperature:
–40 to 85 °C
64-pin QFN
DIF_12
DIF_12
DIF_11
DIF_11


VDD
GND


DIF_13
DIF_13

Fifteen 0.7 V low-power, pushpull HCSL PCIe Gen3 outputs
100 MHz /133 MHz PLL
operation, supports PCIe and
QPI
PLL bandwidth SW SMBUS
programming overrides the latch
value from HW pin
9 selectable SMBUS addresses
SMBus address configurable to
allow multiple buffers in a single
control network 3.3 V supply
voltage operation
VDD_IO
DIF_14
DIF_14

Data center
 Enterprise switches and routers

Description
The Si53115 is a 15-output, low-power HCSL differential clock buffer that
meets all of the performance requirements of the Intel DB1200ZL
specification. The device is optimized for distributing reference clocks for
Intel® QuickPath Interconnect (Intel QPI), PCIe Gen 1/Gen 2/Gen 3/
Gen 4, SAS, SATA, and Intel Scalable Memory Interconnect (Intel SMI)
applications. The VCO of the device is optimized to support 100 MHz and
133 MHz operation. Each differential output can be enabled through I2C
for maximum flexibility and power savings. Measuring PCIe clock jitter is
quick and easy with the Silicon Labs PCIe Clock Jitter Tool. Download it
for free at www.silabs.com/pcie-learningcenter.
Rev. 1.2 2/16
Copyright © 2016 by Silicon Laboratories
VDDA
GNDA
100M_133M
HBW_BYPASS_LBW
PWRGD / PWRDN
GND
VDDR
CLK_IN
CLK_IN
SA_0
SDA
SCL
SA_1
FBOUT_NC
FBOUT_NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GND 16
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
Si53115
VDD_IO
GND
DIF_9
DIF_9
DIF_8
DIF_8
GND
VDD
DIF_7
DIF_7
DIF_6
DIF_6
VDD_IO
GND
DIF_5
DIF_5
DIF_0 17
DIF_0 18
VDD_IO 19
GND 20
DIF_1 21
DIF_1 22
DIF_2 23
DIF_2 24
GND 25
VDD 26
DIF_3 27
DIF_3 28
DIF_4 29
DIF_4 30
VDD_IO 31
GND 32
Server
 Storage

Patents pending
Si53115
S i 5 3 11 5
Functional Block Diagram
FB_OUT
SSC Compatible
PLL
CLK_IN
CLK_IN
100M_133
HBW_BYPASS_LBW
SA_0
SA_1
PWRGD / PWRDN
SDA
SCL
2
Control
Logic
Rev. 1.2
DIF_[14:0]
Si53115
TABLE O F C ONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1. CLK_IN, CLK_IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2. 100M_133M—Frequency Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3. SA_0, SA_1—Address Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4. CKPWRGD/PWRDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.5. HBW_BYPASS_LBW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.6. Miscellaneous Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Test and Measurement Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1. Input Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2. Termination of Differential Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1. Byte Read/Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2. Block Read/Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.3. Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. Pin Descriptions: 64-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6. Power Filtering Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.1. Ferrite Bead Power Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Rev. 1.2
3
S i 5 3 11 5
1. Electrical Specifications
Table 1. DC Operating Characteristics
VDD_A = 3.3 V±5%, VDD = 3.3 V±5%
Parameter
Symbol
Test Condition
Min
Max
Unit
VDD/VDD_A
3.3 V ±5%
3.135
3.465
V
VDD_IO
1.05 V to 3.3 V ±5%
0.9975
3.465
V
3.3 V Input High Voltage
VIH
VDD
2.0
VDD+0.3
V
3.3 V Input Low Voltage
VIL
VSS–0.3
0.8
V
3.3 V Core Supply Voltage
3.3 V I/O Supply
Input Leakage
Voltage1
Current2
IIL
0 < VIN < VDD
–5
+5
µA
3
3.3 V Input High Voltage
VIH_FS
VDD
0.7
VDD+0.3
V
3
3.3 V Input Low Voltage
VIL_FS
VSS–0.3
0.35
V
3.3 V Input Low Voltage
VIL_Tri
0
0.8
V
3.3 V Input Med Voltage
VIM_Tri
1.2
1.8
V
3.3 V Input High Voltage
VIH_Tri
2.2
VDD
V
Voltage4
VOH
IOH = –1 mA
2.4
—
V
3.3 V Output Low Voltage4
VOL
IOL = 1 mA
—
0.4
V
CIN
2.5
4.5
pF
COUT
2.5
4.5
pF
LPIN
—
7
nH
–40
85
°C
3.3 V Output High
Input Capacitance
Output
5
Capacitance5
Pin Inductance
Ambient Temperature
TA
No Airflow
Notes:
1. VDD_IO applies to the low-power NMOS push-pull HCSL compatible outputs.
2. Input Leakage Current does not include inputs with pull-up or pull-down resistors. Inputs with resistors should state
current requirements.
3. Internal voltage reference is to be used to guarantee VIH_FS and VIL_FS thresholds levels over full operating range.
4. Signal edge is required to be monotonic when transitioning through this region.
5. Ccomp capacitance based on pad metalization and silicon device capacitance. Not including pin capacitance.
4
Rev. 1.2
Si53115
Table 2. SMBus Characteristics
Parameter
Symbol
Test Condition
Min
Max
Unit
0.8
V
VDDSMB
V
0.4
V
5.5
V
1
SMBus Input Low Voltage
VILSMB
SMBus Input High Voltage1
VIHSMB
SMBus Output Low Voltage1
VOLSMB
@ IPULLUP
Nominal Bus Voltage1
VDDSMB
@ VOL
2.7
Current1
IPULLUP
3 V to 5 V +/-10%
4
SCLK/SDAT Rise Time1
tRSMB
(Max VIL – 0.15) to (Min VIH + 0.15)
1000
ns
SCLK/SDAT Fall Time1
tFSMB
(Min VIH + 0.15) to (Max VIL – 0.15)
300
ns
fMINSMB
Minimum Operating Frequency
SMBus Sink
SMBus Operating Frequency1, 2
2.1
mA
100
kHz
Notes:
1. Guaranteed by design and characterization.
2. The differential input clock must be running for the SMBus to be active.
Table 3. Current Consumption
TA = -40–85 °C; supply voltage VDD = 3.3 V ±5%
Parameter
Operating Current
Power Down Current
Symbol
Test Condition
Min
Typ
Max
Unit
IDDVDD
133 MHz, VDD Rail
—
25
30
mA
IDDVDDA
133 MHz, VDDA + VDDR, PLL Mode
—
20
25
mA
IDDVDDIO
133 MHz, CL = Full Load, VDD IO Rail
—
100
110
mA
IDDVDDPD
Power Down, VDD Rail
—
0.5
1
mA
IDDVDDAPD
Power Down, VDDA Rail
—
4
7
mA
IDDVDDIOPD
Power Down, VDD_IO Rail
—
0.4
0.7
mA
Rev. 1.2
5
S i 5 3 11 5
Table 4. Clock Input Parameters
TA = -40–85 °C; supply voltage VDD = 3.3 V ±5%
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Input High Voltage
VIHDIF
Differential Inputs
(singled-ended measurement)
600
700
1150
mV
Input Low Voltage
VIHDIF
Differential Inputs
(singled-ended measurement)
Vss300
0
300
mV
Input Common Mode Voltage
Vcom
Common mode input voltage
300
1000
mV
Input Amplitude—CLK_IN
Vswing
Peak to Peak Value
300
1450
mV
Input Slew Rate—CLK_IN
dv/dt
Measured differentially
0.4
8
V/ns
Measurement from differential wave
form
45
55
%
125
ps
150
MHz
Input Duty Cycle
50
Input Jitter—Cycle to Cycle
JDFin
Differential measurement
Input Frequency
Fibyp
VDD = 3.3 V, bypass mode
33
FiPLL
VDD = 3.3 V, 100 MHz PLL Mode
90
100
110
MHz
FiPLL
VDD = 3.3 V, 133.33 MHz PLL Mode
120
133.33
147
MHz
fMODIN
Triangle Wave modulation
30
31.5
33
kHz
Input SS Modulation Rate
6
Rev. 1.2
Si53115
Table 5. Output Skew, PLL Bandwidth and Peaking
TA = -40–85 °C; supply voltage VDD = 3.3 V ±5%
Parameter
Test Condition
Min
Typ
Max
Unit
CLK_IN, DIF[x:0]
Input-to-Output Delay in PLL Mode
Nominal Value1,2,3,4
–100
18
100
ps
CLK_IN, DIF[x:0]
Input-to-Output Delay in Bypass Mode
Nominal Value2,4,5
2.5
3.6
4.5
ns
CLK_IN, DIF[x:0]
Input-to-Output Delay Variation in PLL mode
Over voltage and temperature2,4,5
–50
20
50
ps
CLK_IN, DIF[x:0]
Input-to-Output Delay Variation in Bypass Mode
Over voltage and temperature2,4,5
–250
—
250
ps
Output-to-Output Skew across all 15 Outputs
(Common to Bypass and PLL Mode)1,2,3,4,5
0
20
50
ps
PLL Jitter Peaking
(HBW_BYPASS_LBW = 0)6
—
0.4
2.0
dB
PLL Jitter Peaking
(HBW_BYPASS_LBW = 1)6
—
0.1
2.5
dB
PLL Bandwidth
(HBW_BYPASS_LBW = 0)
7
—
0.7
1.4
MHz
PLL Bandwidth
(HBW_BYPASS_LBW = 1)7
—
2
4
MHz
DIF[11:0]
Notes:
1. Measured into fixed 2 pF load cap. Input-to-output skew is measured at the first output edge following the
corresponding input.
2. Measured from differential cross-point to differential cross-point.
3. This parameter is deterministic for a given device.
4. Measured with scope averaging on to find mean value.
5. All Bypass Mode Input-to-Output specs refer to the timing between an input edge and the specific output edge created
by it.
6. Measured as maximum pass band gain. At frequencies within the loop BW, highest point of magnification is called PLL
jitter peaking.
7. Measured at 3 db down or half power point.
Rev. 1.2
7
S i 5 3 11 5
Table 6. Phase Jitter
Parameter
Phase Jitter
PLL Mode
Test Condition
Min
Typ
Max
Units
—
29
86
ps
PCIe Gen 2 Low Band, Common Clock1,2,3
F < 1.5 MHz1,3,4,5
—
1.0
3.0
ps
(RMS)
PCIe Gen 2 High Band, Common Clock1,2,3
1.5 MHz < F < Nyquist1,3,4,5
—
1.7
3.1
ps
(RMS)
PCIe Gen 3, Common Clock1,2,3
(PLL BW 2–4 MHz, CDR = 10 MHz)1,3,4,5
—
0.45
1.0
ps
(RMS)
PCIe Gen 3 Separate Reference No Spread, SRNS
(PLL BW of 2–4 or 2–5 MHz, CDR = 10 MHz)1,3,4,5
—
0.32
0.71
ps
(RMS)
PCIe Gen 4, Common Clock
(PLL BW of 2–4 or 2–5 MHz, CDR = 10 MHz)1,4,5,8
—
0.45
1.0
ps
(RMS)
Intel® QPI & Intel SMI
(4.8 Gbps or 6.4 Gb/s, 100 or 133 MHz, 12 UI)1,6,7
—
0.21
0.5
ps
(RMS)
Intel QPI & Intel SMI
(8 Gb/s, 100 MHz, 12 UI)1,6
—
0.13
0.3
ps
(RMS)
Intel QPI & Intel SMI
(9.6 Gb/s, 100 MHz, 12 UI)1,6
—
0.11
0.2
ps
(RMS)
PCIe Gen 1, Common Clock
1,2,3
Notes:
1. Post processed evaluation through Intel supplied Matlab* scripts. Defined for a BER of 1E-12. Measured values at a
smaller sample size have to be extrapolated to this BER target.
2. ζ = 0.54 implies a jitter peaking of 3 dB.
3. PCIe* Gen3 filter characteristics are subject to final ratification by PCISIG. Check the PCI-SIG for the latest
specification.
4. Measured on 100 MHz PCIe output using the template file in the Intel-supplied Clock Jitter Tool V1.6.3.
5. Measured on 100 MHz output using the template file in the Intel-supplied Clock Jitter Tool V1.6.3.
6. Measured on 100 MHz, 133 MHz output using the template file in the Intel-supplied Clock Jitter Tool V1.6.3.
7. These jitter numbers are defined for a BER of 1E-12. Measured numbers at a smaller sample size have to be
extrapolated to this BER target.
8. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5.
9. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter.
8
Rev. 1.2
Si53115
Table 6. Phase Jitter (Continued)
Additive Phase Jitter
Bypass Mode
PCIe Gen 11,2,3
—
10
—
ps
PCIe Gen 2 Low Band
F < 1.5 MHz1,3,4,5
—
1.0
—
ps
(RMS)
PCIe Gen 2 High Band
1.5 MHz < F < Nyquist1,3,4,5
—
1.0
—
ps
(RMS)
PCIe Gen 3
(PLL BW 2–4 MHz, CDR = 10 MHz)1,3,4,5
—
0.3
—
ps
(RMS)
PCIe Gen 4, Common Clock
(PLL BW of 2–4 or 2–5 MHz, CDR = 10 MHz)1,4,5,8
—
0.3
—
ps
(RMS)
Intel QPI & Intel® SMI
(4.8 Gbps or 6.4 Gb/s, 100 or 133 MHz, 12 UI)1,6,7
—
0.12
—
ps
(RMS)
Intel QPI & Intel® SMI
(8 Gb/s, 100 MHz, 12 UI)1,6
—
0.1
—
ps
(RMS)
Intel QPI & Intel® SMI
(9.6 Gb/s, 100 MHz, 12 UI)1,6
—
0.1
—
ps
(RMS)
Notes:
1. Post processed evaluation through Intel supplied Matlab* scripts. Defined for a BER of 1E-12. Measured values at a
smaller sample size have to be extrapolated to this BER target.
2. ζ = 0.54 implies a jitter peaking of 3 dB.
3. PCIe* Gen3 filter characteristics are subject to final ratification by PCISIG. Check the PCI-SIG for the latest
specification.
4. Measured on 100 MHz PCIe output using the template file in the Intel-supplied Clock Jitter Tool V1.6.3.
5. Measured on 100 MHz output using the template file in the Intel-supplied Clock Jitter Tool V1.6.3.
6. Measured on 100 MHz, 133 MHz output using the template file in the Intel-supplied Clock Jitter Tool V1.6.3.
7. These jitter numbers are defined for a BER of 1E-12. Measured numbers at a smaller sample size have to be
extrapolated to this BER target.
8. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5.
9. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter.
Rev. 1.2
9
S i 5 3 11 5
Table 7. DIF 0.7 V AC Timing Characteristics (Non-Spread Spectrum Mode)1
Parameter
Symbol
Clock Stabilization Time2
Long Term Accuracy3,4,5
CLK 100 MHz, 133 MHz
Unit
Min
Typ
Max
TSTAB
—
1.5
1.8
ms
LACC
—
—
100
ppm
3,4,6
TABS
9.94900
—
10.05100
ns
Absolute Host CLK Period (133 MHz)3,4,6
TABS
7.44925
—
7.55075
ns
Edge_rate
1.0
3.0
4.0
V/ns
∆ Trise
—
—
125
ps
∆ Tfall
—
—
125
ps
TRISE_MAT/TFALL_MAT
—
7
20
%
Voltage High (typ 0.7 V)3,8,12
VHIGH
660
750
850
mV
Voltage Low (typ 0.7 V)3,8,13
VLOW
–150
15
150
mV
Maximum Voltage
VMAX
—
850
1150
mV
Minimum Voltage
VMIN
–300
—
—
mV
VoxABS
300
450
550
mV
Total ∆ Vox
—
14
140
mV
DC
45
—
55
%
Vovs
—
—
VHigh + 0.3
V
Absolute Host CLK Period (100 MHz)
Slew Rate
3,4,7
Rise Time
Variation3,8,9
Fall Time Variation
3,8,9
Rise/Fall Matching3,8,10,11
Absolute Crossing Point Voltages3,8,14,15,16
Total Variation of Vcross Over All Edges 3,8,18
Duty Cycle
3,5
Maximum Voltage (Overshoot) 3,8,19
10
Rev. 1.2
Si53115
Table 7. DIF 0.7 V AC Timing Characteristics (Non-Spread Spectrum Mode)1 (Continued)
Parameter
Symbol
CLK 100 MHz, 133 MHz
Min
Typ
Max
Unit
Maximum Voltage (Undershoot) 3,8,20
Vuds
—
—
VLow – 0.3
V
Ringback Voltage
Vrb
0.2
—
N/A
V
Notes:
1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2. This is the time from the valid CLK_IN input clocks and the assertion of the PWRGD signal level at 1.8–2.0 V to the
time that stable clocks are output from the buffer chip (PLL locked).
3. Test configuration is Rs = 33.2 , 2 pF for 100  transmission line; Rs = 27 , 2 pF for 85  transmission line.
4. Measurement taken from differential waveform.
5. Using frequency counter with the measurement interval equal or greater than 0.15 s, target frequencies are
99,750,00 Hz, 133,000,000 Hz.
6. The average period over any 1 µs period of time must be greater than the minimum and less than the maximum
specified period.
7. Measure taken from differential waveform on a component test board. The edge (slew) rate is measured from
–150 mV to +150 mV on the differential waveform. Scope is set to average because the scope sample clock is making
most of the dynamic wiggles along the clock edge. Only valid for Rising clock and Falling CLOCK. Signal must be
monotonic through the Vol to Voh region for Trise and Tfall.
8. Measurement taken from single-ended waveform.
9. Measured with oscilloscope, averaging off, using min max statistics. Variation is the delta between min and max.
10. Measured with oscilloscope, and averaging on. The difference between the rising edge rate (average) of clock verses
the falling edge rate (average) of CLOCK.
11. Rise/Fall matching is derived using the following, 2*(Trise – Tfall) / (Trise + Tfall).
12. VHigh is defined as the statistical average High value as obtained by using the Oscilloscope VHigh Math function.
13. VLow is defined as the statistical average Low value as obtained by using the Oscilloscope VLow Math function.
14. Measured at crossing point where the instantaneous voltage value of the rising edge of CLK equals the falling edge of
CLK.
15. This measurement refers to the total variation from the lowest crossing point to the highest, regardless of which edge
is crossing.
16. The crossing point must meet the absolute and relative crossing point specifications simultaneously.
17. Vcross(rel) Min and Max are derived using the following, Vcross(rel) Min = 0.250 + 0.5 (Vhavg – 0.700), Vcross(rel)
Max = 0.550 – 0.5 (0.700 – Vhavg), (see Figure 3–4 for further clarification).
18. Vcross is defined as the total variation of all crossing voltages of Rising CLOCK and Falling CLOCK. This is the
maximum allowed variance in Vcross for any particular system.
19. Overshoot is defined as the absolute value of the maximum voltage.
20. Undershoot is defined as the absolute value of the minimum voltage.
Rev. 1.2
11
S i 5 3 11 5
Table 8. Clock Periods Differential Clock Outputs with SSC Disabled
SSC OFF
Center
Freq, MHz
Measurement Window
1 Clock
–C-C
Jitter
AbsPer
Min
1 µs
0.1 s
–ppm
–SSC
Long
Short
Term AVG Term AVG
Min
Min
0.1 s
Unit
0.1 s
1 µs
0 ppm
Period
Nominal
+SSC
+ppm
Short
Long
Term AVG Term AVG
Max
Max
1 Clock
+C-C
Jitter
AbsPer
Max
100.00
9.94900
9.99900
10.00000
10.00100
10.05100
ns
133.33
7.44925
7.49925
7.50000
7.50075
7.55075
ns
Table 9. Clock Periods Differential Clock Outputs with SSC Enabled
SSC ON
Center
Freq, MHz
Measurement Window
1 Clock
–C-C
Jitter
AbsPer
Min
1 µs
0.1 s
–ppm
–SSC
Long
Short
Term AVG Term AVG
Min
Min
0.1 s
0.1 s
Unit
1 µs
0 ppm
Period
Nominal
+SSC
+ppm
Short
Long
Term AVG Term AVG
Max
Max
1 Clock
+C-C
Jitter
AbsPer
Max
99.75
9.94900
9.99900
10.02406
10.02506
10.02607
10.05126
10.10126
ns
133.33
7.44925
7.49925
7.51805
7.51880
7.51955
7.53845
7.58845
ns
Table 10. Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
VDD/VDD_A
—
4.6
V
VDD_IO
—
4.6
V
VIH
—
4.6
V
VIL
−0.5
—
V
Storage Temperature1
ts
–65
150
°C
Input ESD protection3
ESD
2000
—
V
3.3 V Core Supply Voltage1
3.3 V I/O Supply Voltage1
3.3 V Input High
Voltage1,2
3.3 V Input Low Voltage1
Notes:
1. Consult manufacturer regarding extended operation in excess of normal DC operating parameters.
2. Maximum VIH is not to exceed maximum VDD.
3. Human body model.
12
Rev. 1.2
Si53115
2. Functional Description
2.1. CLK_IN, CLK_IN
The differential input clock is expected to be sourced from a clock synthesizer or PCH.
2.2. 100M_133M—Frequency Selection
The Si53115 is optimized for lowest phase jitter performance at operating frequencies of 100 and 133 MHz.
100M_133M is a hardware input pin, which programs the appropriate output frequency of the differential outputs.
Note that the CLK_IN frequency must be equal to the CLK_OUT frequency; meaning Si53115 is operated in 1:1
mode only. Frequency selection can be enabled by the 100M_133M hardware pin. An external pull-up or pull-down
resistor is attached to this pin to select the input/output frequency. The functionality is summarized in Table 11.
Table 11. Frequency Program Table
100M_133M
Optimized Frequency (DIF_IN = DIF_x)
0
133.33 MHz
1
100.00 MHz
Note: All differential outputs transition from 100 to 133 MHz or from 133 to 100 MHz in a glitch free manner.
2.3. SA_0, SA_1—Address Selection
SA_0 and SA_1 are tri-level hardware pins, which program the appropriate address for the Si53115. These are the
two tri-level input pins that can configure the device to nine different addresses.
Table 12. SMBUS Address Table
SA_1
SA_0
SMBUS Address
L
L
D8
L
M
DA
L
H
DE
M
L
C2
M
M
C4
M
H
C6
H
L
CA
H
M
CC
H
H
CE
Rev. 1.2
13
S i 5 3 11 5
2.4. CKPWRGD/PWRDN
CKPWRGD is asserted high and deasserted low. Deassertion of PWRGD (pulling the signal low) is equivalent to
indicating a power down condition. CKPWRGD (assertion) is used by the Si53115 to sample initial configurations,
such as frequency select conditions and SA selections. After CKPWRGD has been asserted high for the first time,
the pin becomes a PWRDN (Power Down) pin that can be used to shut off all clocks cleanly and instruct the device
to invoke power-saving mode. PWRDN is a completely asynchronous active low input. When entering powersaving mode, PWRDN should be asserted low prior to shutting off the input clock or power to ensure all clocks shut
down in a glitch free manner. When PWRDN is asserted low, all clocks will be disabled prior to turning off the VCO.
When PWRDN is deasserted high, all clocks will start and stop without any abnormal behavior and will meet all AC
and DC parameters.
Note: The assertion and deassertion of PWRDN is absolutely asynchronous.
Warning: Disabling of the CLK_IN input clock prior to assertion of PWRDN is an undefined mode and not recommended.
Operation in this mode may result in glitches, excessive frequency shifting, etc.
Table 13. CKPWRGD/PWRDN Functionality
CKPWRGD/
PWRDN
DIF_IN/
DINF_IN#
SMBus
EN bit
DIF-x/
DIF_x#
FBOUT_NC/
FBOUT_NC#
PLL State
0
X
X
Low/Low
Low/Low
OFF
1
Running
0
Low/Low
Running
ON
1
Running
Running
ON
14
Rev. 1.2
Si53115
2.4.1. PWRDN Assertion
When PWRDN is sampled low by two consecutive rising edges of DIF, all differential outputs must be held LOW/
LOW on the next DIF high-to-low transition.
PWRDWN
DIF
DIF
Figure 1. PWRDN Assertion
2.4.2. CKPWRGD Assertion
The power up latency is to be less than 1.8 ms. This is the time from a valid CLK_IN input clock and the assertion
of the PWRGD signal to the time that stable clocks are output from the device (PLL locked). All differential outputs
stopped in a LOW/LOW condition resulting from power down must be driven high in less than 300 µs of PWRDN
deassertion to a voltage greater than 200 mV.
Tstable
<1.8 ms
DIF
DIF
Tdrive_Pwrdn#
<300 µs; > 200 mV
Figure 2. PWRDG Assertion (Pwrdown—Deassertion)
Rev. 1.2
15
S i 5 3 11 5
2.5. HBW_BYPASS_LBW
The HBW_BYPASS_LBW pin is a tri-level function input pin (refer to Table 1 for VIL_Tri, VIM_Tri, and VIH_Tri
signal levels). It is used to select between PLL high-bandwidth, PLL bypass mode, or PLL low-bandwidth mode. In
PLL bypass mode, the input clock is passed directly to the output stage, which may result in up to 50 ps of additive
cycle-to-cycle jitter (50 ps + input jitter) on the differential outputs. In the PLL mode, the input clock is passed
through a PLL to reduce high-frequency jitter. The PLL HBW, BYPASS, and PLL LBW modes may be selected by
asserting the HBW_BYPASS_LBW input pin to the appropriate level described in Table 14.
Table 14. PLL Bandwidth and Readback Table
HBW_BYPASS_LBW Pin
Mode
Byte 0, Bit 7
Byte 0, Bit 6
L
LBW
0
0
M
BYPASS
0
1
H
HBW
1
1
The Si53115 has the ability to override the latch value of the PLL operating mode from hardware strap Pin 5 via the
use of Byte 0 and Bits 2 and 1. Byte 0 Bit 3 must be set to 1 to allow the user to change Bits 2 and 1, affecting the
PLL. Bits 7 and 6 will always read back the original latched value. A warm reset of the system will have to be
accomplished if the user changes these bits.
2.6. Miscellaneous Requirements
Data Transfer Rate: 100 kbps (standard mode) is the base functionality required. Fast mode (400 kbps)
functionality is optional.
Logic Levels: SMBus logic levels are based on a percentage of VDD for the controller and other devices on the
bus. Assume all devices are based on a 3.3 V supply.
Clock Stretching: The clock buffer must not hold/stretch the SCL or SDA lines low for more than 10 ms. Clock
stretching is discouraged and should only be used as a last resort. Stretching the clock/data lines for longer than
this time puts the device in an error/time-out mode and may not be supported in all platforms. It is assumed that all
data transfers can be completed as specified without the use of clock/data stretching.
General Call: It is assumed that the clock buffer will not have to respond to the “general call.”
Electrical Characteristics: All electrical characteristics must meet the standard mode specifications found in
Section 3 of the SMBus 2.0 specification.
Pull-Up Resistors: Any internal resistor pull-ups on the SDATA and SCLK inputs must be stated in the individual
data sheet. The use of internal pull-ups on these pins of below 100 K is discouraged. Assume that the board
designer will use a single external pull-up resistor for each line and that these values are in the 5–6 k range.
Assume one SMBus device per DIMM (serial presence detect), one SMBus controller, one clock buffer, one clock
driver plus one/two more SMBus devices on the platform for capacitive loading purposes.
Input Glitch Filters: Only fast mode SMBus devices require input glitch filters to suppress bus noise. The clock
buffer is specified as a standard mode device and is not required to support this feature. However, it is considered
a good design practice to include the filters.
PWRDN: If a clock buffer is placed in PWRDN mode, the SDATA and SCLK inputs must be Tri-stated and the
device must retain all programming information. IDD current due to the SMBus circuitry must be characterized and
in the data sheet.
16
Rev. 1.2
Si53115
3. Test and Measurement Setup
3.1. Input Edge
Input edge rate is based on single-ended measurement. This is the minimum input edge rate at which the Si53115
is guaranteed to meet all performance specifications.
Table 15. Input Edge Rate
Frequency
Min
Max
Unit
100 MHz
0.35
N/A
V/ns
133 MHz
0.35
N/A
V/ns
3.1.1. Measurement Points for Differential
Slew_fall
Slew_rise
+150 mV
+150 mV
0.0 V
V_swing
0.0 V
-150 mV
-150 mV
Diff
Figure 3. Measurement Points for Rise Time and Fall Time
Vovs
VHigh
Vrb
Vrb
VLow
Vuds
Figure 4. Single-ended Measurement Points for Vovs, Vuds, Vrb
Rev. 1.2
17
S i 5 3 11 5
TPeriod
Low Duty Cycle %
High Duty Cycle %
Skew measurement
point
0.000 V
Figure 5. Differential (CLOCK–CLOCK) Measurement Points (Tperiod, Duty Cycle, Jitter)
3.2. Termination of Differential Outputs
All differential outputs are to be tested into a 100  or 85  differential impedance transmission line. Source
terminated clocks have some inherent limitations as to the maximum trace length and frequencies that can be
supported. For CPU outputs, a maximum trace length of 10” and a maximum of 200 MHz are assumed. For SRC
clocks, a maximum trace length of 16” and maximum frequency of 100 MHz is assumed. For frequencies beyond
200 MHz, trace lengths must be restricted to avoid signal integrity problems.
Table 16. Differential Output Termination
Clock
Board Trace Impedance
Rs
Rp
Unit
DIFF Clocks—50  configuration
100
33+5%
N/A

DIFF Clocks—43  configuration
85
27+5%
N/A

3.2.1. Termination of Differential NMOS Push-Pull Type Outputs
Si53115
Clock Rs
T-Line
10" Typical
Receiver
2 pF
Source Terminated
2 pF
Clock # Rs
T-Line
10" Typical
Figure 6. 0.7 V Configuration Test Load Board Termination for NMOS Push-Pull
18
Rev. 1.2
Si53115
4. Control Registers
4.1. Byte Read/Write
Reading or writing a register in an SMBus slave device in byte mode always involves specifying the register
number.
4.1.1. Byte Read
The standard byte read is as shown in Figure 7. It is an extension of the byte write. The write start condition is
repeated; then, the slave device starts sending data, and the master acknowledges it until the last byte is sent. The
master terminates the transfer with a NAK, then a stop condition. For byte operation, the 2 x 7th bit of the command
byte must be set. For block operations, the 2 x 7th bit must be reset. If the bit is not set, the next byte must be the
byte transfer count.
1
7
T Slave
1 1
8
Wr A Command
Command
starT
Condition
1 1
7
A r Slave
Register # to
read
2 x 7 bit = 1
1 1
8
1 1
Rd A Data Byte 0 N P
repeat starT
Acknowledge
Master to
Byte Read Protocol
Not ack
stoP
Condition
Slave to
Figure 7. Byte Read Protocol
4.1.2. Byte Write
Figure 8 illustrates a simple, typical byte write. For byte operation, the 2 x 7th bit of the command byte must be set.
For block operations, the 2 x 7th bit must be reset. If the bit is not set, the next byte must be the byte transfer count.
The count can be between 1 and 32. It is not allowed to be zero or to exceed 32.
1
7
T Slave
Command
starT Condition
1 1
8
Wr A Command
Register # to
write
2 x 7 bit = 1
1
8
1 1
A Data Byte 0 A P
Acknowledge
Byte Write Protocol
stoP Condition
Master to
Slave to
Figure 8. Byte Write Protocol
Rev. 1.2
19
S i 5 3 11 5
4.2. Block Read/Write
4.2.1. Block Read
After the slave address is sent with the R/W condition bit set, the command byte is sent with the MSB = 0. The
slave acknowledges the register index in the command byte. The master sends a repeat start function. After the
slave acknowledges this, the slave sends the number of bytes it wants to transfer (>0 and <33). The master
acknowledges each byte except the last and sends a stop function.
1
7
T Slave
1 1
8
1 1
7
Wr A Command Code A r Slave
Command
starT
Condition
8
1
Data Byte A
1 1
Rd A
Register # to
repeat starT
read
Acknowledge
2 x 7 bit = 1
8
1
8
1 1
Data Byte 0 A Data Byte 1 N P
Master to
Slave to
Not acknowledge
stoP Condition
Block Read Protocol
Figure 9. Block Read Protocol
4.2.2. Block Write
After the slave address is sent with the R/W condition bit not set, the command byte is sent with the MSB = 0. The
lower seven bits indicate the register at which to start the transfer. If the command byte is 00h, the slave device will
be compatible with existing block mode slave devices. The next byte of a write must be the count of bytes that the
master will transfer to the slave device. The byte count must be greater than zero and less than 33. Following this
byte are the data bytes to be transferred to the slave device. The slave device always acknowledges each byte
received. The transfer is terminated after the slave sends the ACK and the master sends a stop function.
1
7
1 1
T Slave Address Wr A
Command bit
starT
Condition
8
Command
Register # to
write
2 x 7 bit = 0
1
A
Master to
Slave to
Acknowledge
1
8
1
8
1 1
8
Byte Count = 2 A Data Byte 0 A Data Byte 1 A P
stoP Condition
Block Write Protocol
Figure 10. Block Write Protocol
20
Rev. 1.2
Si53115
4.3. Control Registers
Table 17. Byte 0: Frequency Select, Output Enable, PLL Mode Control Register
Bit
Description
If Bit = 0
If Bit = 1
Type
Default
Output(s)
Affected
0
100M_133M#
Frequency Select
133 MHz
100 MHz
R
Latched at
power up
DIF[11:0]
1
Reserved
0
2
Reserved
0
3
Output Enable DIF 13
Low/Low
Enable
RW
1
DIF_13
4
Output Enable DIF 14
Low/Low
Enable
RW
1
DIF_14
5
Reserved
0
6
PLL Mode 0
See PLL Operating Mode
Readback Table
R
Latched at
power up
7
PLL Mode 1
See PLL Operating Mode
Readback Table
R
Latched at
power up
Table 18. Byte 1: Output Enable Control Register
Bit
Description
0
If Bit = 0
If Bit = 1
Type
Reserved
Default
Output(s)
Affected
0
1
Output Enable DIF 0
Low/Low
Enabled
RW
1
DIF[0]
2
Output Enable DIF 1
Low/Low
Enabled
RW
1
DIF[1]
3
Output Enable DIF 2
Low/Low
Enabled
RW
1
DIF[2]
4
Output Enable DIF 3
Low/Low
Enabled
RW
1
DIF[3]
5
Output Enable DIF 4
Low/Low
Enabled
RW
1
DIF[4]
6
7
Reserved
Output Enable DIF 5
Low/Low
0
Enabled
Rev. 1.2
RW
1
DIF[5]
21
S i 5 3 11 5
Table 19. Byte 2: Output Enable Control Register
Bit
Description
If Bit = 0
If Bit = 1
Type
Default
Output(s)
Affected
0
Output Enable DIF 6
Low/Low
Enabled
RW
1
DIF[6]
1
Output Enable DIF 7
Low/Low
Enabled
RW
1
DIF[7]
2
Output Enable DIF 8
Low/Low
Enabled
RW
1
DIF[8]
3
Output Enable DIF 9
Low/Low
Enabled
RW
1
DIF[9]
4
Reserved
0
5
Output Enable DIF 10
Low/Low
Enabled
RW
1
DIF[10]
6
Output Enable DIF 11
Low/Low
Enabled
RW
1
DIF[11]
7
Output Enable DIF 12
Low/Low
Enabled
RW
1
DIF[12]
Default
Output(s)
Affected
Table 20. Byte 3: Reserved Control Register
22
Bit
Description
If Bit = 0
0
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
Rev. 1.2
If Bit = 1
Type
Si53115
Table 21. Byte 4: Reserved Control Register
Bit
Description
If Bit = 0
If Bit = 1
Type
Default
0
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
Output(s)
Affected
Table 22. Byte 5: Vendor/Revision Identification Control Register
Bit
Description
0
If Bit = 0
If Bit = 1
Type
Default
Output(s)
Affected
Vendor ID Bit 0
R
Vendor Specific
0
1
Vendor ID Bit 1
R
Vendor Specific
0
2
Vendor ID Bit 2
R
Vendor Specific
0
3
Vendor ID Bit 3
R
Vendor Specific
1
4
Revision Code Bit 0
R
Vendor Specific
0
5
Revision Code Bit 1
R
Vendor Specific
0
6
Revision Code Bit 2
R
Vendor Specific
0
7
Revision Code Bit 3
R
Vendor Specific
0
Table 23. Byte 6: Device ID Control Register
Bit
Description
0
If Bit = 0
If Bit = 1
Type
Default
Device ID 0
R
0
1
Device ID 1
R
1
2
Device ID 2
R
1
3
Device ID 3
R
1
4
Device ID 4
R
0
5
Device ID 5
R
1
6
Device ID 6
R
1
7
Device ID 7 (MSB)
R
1
Rev. 1.2
Output(s)
Affected
23
S i 5 3 11 5
Table 24. Byte 7: Byte Count Register
24
Bit
Description
0
If Bit = 0
If Bit = 1
Type
Default
BC0: Writing to this register
configures how many bytes will
be read back
RW
0
1
BC1: Writing to this register
configures how many bytes will
be read back
RW
0
2
BC2: Writing to this register
configures how many bytes will
be read back
RW
0
3
BC3: Writing to this register
configures how many bytes will
be read back
RW
1
4
BC4: Writing to this register
configures how many bytes will
be read back
RW
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
Rev. 1.2
Output(s)
Affected
Si53115
GND
VDD_IO
DIF_10
DIF_10
DIF_12
DIF_12
DIF_11
DIF_11
VDD
GND
DIF_13
DIF_13
GND
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
VDD_IO
DIF_14
DIF_14
5. Pin Descriptions: 64-Pin QFN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GND 16
Si53115
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VDD_IO
GND
DIF_9
DIF_9
DIF_8
DIF_8
GND
VDD
DIF_7
DIF_7
DIF_6
DIF_6
VDD_IO
GND
DIF_5
DIF_5
DIF_0 17
DIF_0 18
VDD_IO 19
GND 20
DIF_1 21
DIF_1 22
DIF_2 23
DIF_2 24
GND 25
VDD 26
DIF_3 27
DIF_3 28
DIF_4 29
DIF_4 30
VDD_IO 31
GND 32
VDDA
GNDA
100M_133M
HBW_BYPASS_LBW
PWRGD / PWRDN
GND
VDDR
CLK_IN
CLK_IN
SA_0
SDA
SCL
SA_1
FBOUT_NC
FBOUT_NC
Rev. 1.2
25
S i 5 3 11 5
Table 25. Si53115 64-Pin QFN Descriptions
Pin #
Name
Type
1
VDDA
3.3 V 3.3 V power supply for PLL.
2
GNDA
GND
Ground for PLL.
3
100M_133M
I,SE
3.3 V tolerant inputs for input/output frequency selection. An external pullup or pull-down resistor is attached to this pin to select the input/output
frequency.
High = 100 MHz output
Low = 133 MHz output
4
HBW_BYPASS_LBW
I, SE
Tri-Level input for selecting the PLL bandwidth or bypass mode.
High = High BW mode
Med = Bypass mode
Low = Low BW mode
5
PWRGD/PWRDN
I
6
GND
GND
Ground for outputs.
7
VDDR
VDD
3.3 V power supply for differential input receiver. This VDDR should be
treated as an analog power rail and filtered appropriately.
8
CLK_IN
I, DIF 0.7 V Differential input.
9
CLK_IN
I, DIF 0.7 V Differential input.
10
SA_0
I,PU
11
SDA
I/O
Open collector SMBus data.
12
SCL
I/O
SMBus slave clock input.
13
SA_1
I,PU
14
FBOUT_NC
I/O
Complementary differential feedback output. There are active signals on
Pins 15 and 16, do not connect anything to this pin.
15
FBOUT_NC
I/O
True differential feedback output. There are active signals on Pins 15 and
16; do not connect anything to Pin 15.
16
GND
GND
17
DIF_0
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
18
DIF_0
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
19
VDDIO
20
GND
21
DIF_1
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
22
DIF_1
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
23
DIF_2
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
24
DIF_2
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
26
Description
3.3 V LVTTL input to power up or power down the device.
3.3 V LVTTL input selecting the address. Tri-level input.
3.3 V LVTTL input selecting the address. Tri-level input.
Ground for outputs.
3.3 V 3.3 V power supply for differential outputs.
GND
Ground for outputs.
Rev. 1.2
Si53115
Table 25. Si53115 64-Pin QFN Descriptions (Continued)
Pin #
Name
Type
Description
25
GND
GND
26
VDD
3.3 V 3.3 V power supply.
27
DIF_3
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
28
DIF_3
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
29
DIF_4
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
30
DIF_4
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
31
VDD_IO
VDD
Power supply for differential outputs.
32
GND
GND
Ground for outputs.
33
DIF_5
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
34
DIF_5
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
35
GND
GND
Ground for outputs.
36
VDD_IO
VDD
Power supply for differential outputs.
37
DIF_6
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
38
DIF_6
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
39
DIF_7
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
40
DIF_7
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
41
VDD
3.3 V 3.3 V power supply.
42
GND
GND
43
DIF_8
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
44
DIF_8
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
45
DIF_9
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
46
DIF_9
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
47
GND
GND
Ground for outputs.
48
VDD_IO
VDD
Power supply for differential outputs.
49
DIF_10
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
50
DIF_10
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
51
VDD_IO
VDD
Power supply for differential outputs.
52
GND
GND
Ground for outputs.
53
DIF_11
Ground for outputs.
Ground for outputs.
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
Rev. 1.2
27
S i 5 3 11 5
Table 25. Si53115 64-Pin QFN Descriptions (Continued)
Pin #
Name
54
DIF_11
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
55
DIF_12
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
56
DIF_12
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
57
GND
GND
58
VDD
3.3 V 3.3 V power supply for outputs.
59
DIF_13
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
60
DIF_13
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
61
DIF_14
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
62
DIF_14
O, DIF 0.7 V Differential clock outputs. Default is 1:1.
63
VDD_IO
VDD
Power supply for differential outputs.
64
GND
GND
Ground for outputs.
28
Type
Description
Ground for outputs.
Rev. 1.2
Si53115
6. Power Filtering Example
6.1. Ferrite Bead Power Filtering
Silicon Labs recommends using a ferrite bead with characteristics matching Murata BLM15EG221SN1.
Figure 11. Recommended Si53115 Power Filtering
Rev. 1.2
29
S i 5 3 11 5
7. Ordering Guide
Part Number
Package Type
Temperature
Si53115-A01AGM
64-pin QFN
Extended, –40 to 85 C
Si53115-A01AGMR
64-pin QFN—Tape and Reel
Extended, –40 to 85 C
Lead-free
30
Rev. 1.2
Si53115
8. Package Outline
Figure 12 illustrates the package details for the Si53115. Table 26 lists the values for the dimensions shown in the
illustration.
Figure 12. 64-Pin Quad Flat No Lead (QFN) Package
Table 26. Package Dimensions1,2,3,4
Dimension
Min
Nom
Max
Dimension
Min
Nom
Max
A
0.80
0.85
0.90
E2
6.00
6.10
6.20
A1
0.00
0.02
0.05
L
0.30
0.40
0.50
b
0.18
0.25
0.30
aaa
0.10
bbb
0.10
ccc
0.08
D
D2
9.00 BSC.
6.00
6.10
6.20
e
0.50 BSC.
ddd
0.10
E
9.00 BSC.
eee
0.05
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC outline MO-220.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
Rev. 1.2
31
S i 5 3 11 5
DOCUMENT CHANGE LIST
Revision 1.0 to Revision 1.1
Updated Features on page 1.
Updated Description on page 1.
 Updated specs in Table 6, “Phase Jitter,” on page 8.


Revision 1.1 to Revision 1.2
February 22, 2016
 Corrected specs in Table 1, “DC Operating
Characteristics,” on page 4.
 Updated operating characteristics in Table 3,
Table 4, and Table 5.
 Updated package drawing (Figure 12) and package
dimensions (Table 26).
32
Rev. 1.2
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
www.silabs.com/CBPro
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using
or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and
"Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to
make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the
included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses
granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent
of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in
weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,
EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®,
ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand
names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com