AN619: Manually Generating an Si5351 Register Map

AN619
Manually Generating an Si5351 Register Map
1. Introduction
The Si5351 is a highly flexible and configurable clock generator and VCXO. A block diagram of the Si5351
programmable clock IC is shown in Figure 1. To support this flexibility, Silicon Labs has created ClockBuilder
Desktop to create register maps automatically and easily for a given configuration. Since programming with
ClockBuilder Desktop may not always be well suited for every system’s requirements, this document presents the
procedures and equations for determining a complete register set from a frequency plan. Section 2 highlights the
overall frequency plan algorithm, and sections 3 and beyond detail all the necessary register calculations.
Figure 1. Generalized Si5351 Block Diagram
Figure 1 is a generalized block diagram of the Si5351. The Si5351 is available in three variants:
Si5351A—XTAL
only device.
Si5351B—XTAL+VCXO.
Si5351C—XTAL + CLKIN.
If spread spectrum is turned on, it is supported by PLLA. VCXO functionality (Si5351B devices only) is supported
by PLLB.
Rev. 0.6 9/15
Copyright © 2015 by Silicon Laboratories
AN619
AN619
2. Conceptualizing a Frequency Plan
The device consists of two PLLs—PLLA and PLLB. Each PLL consists of a Feedback Multisynth used to generate
an intermediate VCO frequency in the range of 600 to 900 MHz. Either of these two VCO frequencies can be
divided down by the individual output Multisynth dividers to generate a Multisynth frequency between 500 kHz and
200 MHz. Additionally, the R dividers can be used to generate any output frequency down to 2.5 kHz. The
relationship between the VCO and output frequencies is given below.
fvco
fout x = --------------------------------------------Multisynth x  R x
Use the steps in the sections below to draw out a conceptual frequency plan map.
2.1. PLL Selection
If spread spectrum is not enabled, either of the two PLLs may be used as the source for any outputs of the
Si5351A. If both XTAL and CLKIN input options are used simultaneously (Si5351C only), then one PLL must be
reserved for use with CLKIN and one for use with the XTAL.
Note: PLLA must be used for any spread spectrum-enabled outputs. PLLB must be used for any VCXO outputs.
2.1.1. Selecting the Proper VCO Frequencies and Divide Ratios
The general criteria below may be used to set the VCO frequencies. This is a general model, and individual
applications may require some modification.
1. Valid Multisynth divider ratios are 4, 6, 8, and any fractional value between 8 + 1/1,048,575 and 900 + 0/1.
This means that if any output is greater than 112.5 MHz (900 MHz/8), then this output frequency sets one
of the VCO frequencies.
2. For the frequencies where jitter is a concern make the output Multisynth divide ratio an integer. If possible,
make both output and feedback Multisynth ratios integers.
3. Once criteria 1 and 2 are satisfied, try to select as many integer output Multisynth ratios as possible.
2.2. Output Clock Pin Assignment (Optional)
Some customers may wish to have full control of output clock pin assignment. The guidelines below may be used
to assign clocks to pins on the device.
1. Equal output frequencies should share a VDDO bank (e.g., CLOK0&1, CLK2&3, etc.) whenever possible in
order to ensure minimal jitter due to PCB crosstalk.
2. Isolate unique output frequencies on individual VDDO bank if possible. For example, if the four outputs are
25 MHz, 25 MHz, 27 MHz, and 74.25 MHz, then place them on CLK0, CLK1, CLK2, and CLK4,
respectively.
3. Otherwise, use all necessary CLK channels based on the required frequency plan.
Note: The only valid divide ratios for CLK6 and CLK7 Multisynth dividers are even integers between 6 and 254 inclusive. This
may limit the two VCO frequencies if all 8 output clocks are used.
2
Rev. 0.6
AN619
3. Configuring Input and PLL Register Parameters (Synthesis Stage 1)
This section describes register parameters related to the input reference and the two PLLs.
3.1. PLL Input Source
The input source for each PLL must be selected. For the A and B devices, the only possible source is the XTAL,
but for the C device, each PLL can be synchronized to either an XTAL or a CMOS clock on the CLKIN pin.
3.1.1. XTAL Source
If the source for the PLL is a crystal, PLLx_SRC must be set to 0 in register 15. XTAL_CL[1:0] must also be set to
match the crystal load capacitance (see register 183).
3.1.2. CMOS Clock Source
If a PLL needs to be synchronized to a CMOS clock, PLLx_SRC must be 1. The input frequency range of the PLL
is 10 to 40 MHz. If CLKIN is > 40 MHz, the CLKIN input divider must be used to bring the PLL input within the 10–
40 MHz range. See CLKIN_DIV[1:0], register bits 15 [7:6].
3.2. Feedback Multisynth Divider Equations
Once the input source for each PLL and (if necessary) CLKIN_DIV are determined, the two VCO frequencies
selected in Section 2 above can be generated using the following equations. Each feedback divider essentially
multiplies the source frequency such that
b
f VCO = f XTAL   a + ---
c
and/or
f CLKIN
b
f VCO = ---------------------------------   a + ---
CLKIN_DIV
c
The fractional ratio
b
a + --c
has a valid range of 15 + 0/1,048,575 and 90 +0/1,048,575 and is represented in the Si5351 register space using
the equations below.
b
MSNx_P1  17:0  = 128  a + Floor  128  --- – 512
c
b
MSNx_P2  19:0  = 128  b – c  Floor  128  ---

c
MSNx_P3  19:0  = c
In the equations above, x is used to represent MSNA and MSNB, the PLLA and PLLB Multisynth dividers
respectively. The equations above must be repeated for Multisynths NA and NB. As mentioned earlier in Section
“2.1. PLL Selection”, spread spectrum is only supported by PLLA, and the VCXO functionality is only supported by
PLLB. When using the VCXO function, set the MSNB divide ratio a + b/c such that c = 106. This must be taken into
consideration when configuring a frequency plan.
Rev. 0.6
3
AN619
3.2.1. Integer Divide Values (FBx_INT)
If a + b/c is an even integer, integer mode may be enabled for PLLA or PLLB by setting parameter FBA_INT or
FBB_INT respectively. In most cases setting this bit will improve jitter when using even integer divide values.
Whenever spread spectrum is enabled, FBA_INT must be set to 0.
3.3. Miscellaneous PLL Parameters
Set PLLA_CL=2
Set PLLB_CL=2
4
Rev. 0.6
AN619
4. Configuring the Output Register Parameters
This section covers the Multisynth and output driver settings necessary for each output. As shown in Figure 2, one
of the two VCO frequencies is divided down by each Multisynth divider. This is followed by an output driver state.
See “4.2. Output Driver Settings”.
XO
CMOS
VCOA
VCOB
Multisynth0
÷M0
÷R0
CLK0
÷R1
CLK1
M0
XO
CMOS
VCOA
VCOB
M0
Multisynth1
÷M1
M1
XO
CMOS
VCOA
VCOB
M0
Multisynth2
÷M2
÷R2
CLK2
M2
XO
CMOS
XO
CLKIN
PLLA
NA
M0
VCOA
VCOB
Multisynth3
÷M3
÷R3
CLK3
M3
XO
CMOS
÷R4
XO
CLKIN
VCOA
PLLB
NB
VCOB
Multisynth4
÷M4
CLK4
M4
XO
CMOS
VCOA
VCOB
M4
Multisynth5
÷M5
÷R5
CLK5
M5
XO
CMOS
VCOA
VCOB
M4
Multisynth6
÷M6*
÷R6
CLK6
M6
XO
CMOS
VCOA
VCOB
M4
Multisynth7
÷M7*
÷R7
CLK7
M7
* Multisynth 6 and 7 divide ratios can only be even integers between 6 and 254.
Figure 2. Detailed Dividers and Output Drivers Block Diagram
Rev. 0.6
5
AN619
4.1. Output Multisynth Settings (Synthesis Stage 2)
This section describes the settings related to the individual Multisynths. The Si5351 consists of six fractional
Multisynth divides (MS0-MS5) and even-integer dividers (MS6 and MS7).
4.1.1. Output Multisynth Source (MSx_SRC)
Each of these dividers can be set to use PLLA or PLLB as its reference by setting MSx_SRC to 0 or 1 respectively.
See bit 5 description of registers 16-23.
4.1.2. Output Multisynth Divider Equations (Fout <= 150 MHz)
Once the PLL source for the individual Multisynth is selected, the divide ratio can be set using the equations below.
Divider represented as fractional number,
b
a + --c
between 6 and 1800.
b
MSx_P1  17:0  = 128  a + Floor  128  --- – 512

c
b
MSx_P2  19:0  = 128  b – c  Floor  128  ---
c
MSx_P3  19:0  = c
In the equations above, x=0, 1, ...5. As previously noted, MS6 and MS7 are integer-only dividers. The valid range
of values for these dividers is all even integers between 6 and 254 inclusive. For MS6 and MS7, set MSx_P1
directly (e.g., MSx_P1=divide value).
4.1.2.1. Integer Divide Values(MSx_INT)
If any of the MS0-MS5 is an even integer, Multisynth integer mode may be enabled by setting MSx_INT=1 (see
registers 16-21, bit 6). In most cases setting this bit will improve jitter when using even integer divide values.
Multisynths 6 and 7 inherently operate in integer mode, and so there is no register to turn integer mode on or off.
4.1.3. Output Multisynth Divider Equations (150 MHz <Fout<=200 MHz)
Output frequencies greater than 150 MHz are available on Multisynths 0-5. For this frequency range a divide value
of 4 must be used by setting
MSx_P1=0,
MSx_P2=0,
MSx_P3=1,
MSx_INT=1,
and
MSx_DIVBY4[1:0]=11b.
Set the appropriate feedback Multisynth to generate fVCO=Fout*4.
4.2. Output Driver Settings
Once the Multisynth registers are assembled, the output driver settings can be modified according to the
information in this section.
4.2.1. Clock Source (CLKx_SRC)
Generally, Multisynth x should be output on CLKx, however XO, CLKIN, or a divided version of either (see section
4.2.2 on R dividers) may also be output on each of the CLKx pins. Additionally, MS0 (or a divided version of MS0)
may be output on CLK0-CLK3, and MS4 (or a divided version of MS4) may be output on CLK4-CLK7. See
CLKx_SRC description for details.
4.2.2. R Dividers
The R dividers can be used to generate frequencies below about 500 kHz. Each individual output R divider can be
set to 1, 2, 4, 8,....128 by writing the proper setting for Rx_DIV. Set this parameter to generate frequencies down to
8kHz.
6
Rev. 0.6
AN619
4.2.3. (CLKx_INV)
In some cases, the user may need to invert the polarity (i.e., 180° phase offset) of one or more outputs with respect
to the other outputs. This is achieved by setting CLKx_INV=1.
4.2.4. (CLKx_DIS_STATE)
When a clock is disabled via the OEB pin or OEB control register (reg 3), the output driver may be set to present a
logic low, logic high, or high-impedance at the device pin. See CLKx_DIS_STATE description for details.
4.2.5. Unused Clock Outputs
Any unused clock outputs may be powered down to reduce IDDO current consumption. Set CLKx_PDN=1 to
power down unused clock output drivers.
Rev. 0.6
7
AN619
5. Configuring Spread Spectrum Register Parameters
Spread spectrum can be enabled on any Multisynth output that uses PLLA as its reference. Valid ranges for spread
spectrum include –0.1% to –2.5% down spread and up to ± 1.5% center spread. This spread modulation rate is
fixed at approximately 31.5 kHz.
The following parameters must be known to properly set up spread spectrum:
fPFD(A)
input frequency to PLLA (determined in Sec 2 above and referred to in “3.1.2. CMOS Clock
Source”). This is also listed in the ClockBuilder Desktop generated register map file as “#PFD(MHz)=...”
a + b/c PLLA Multisynth radio (determined in Sec 2 above). This is also listed in register map file as
“#Feedback Divider=...”
sscAMPSpread amplitude (e.g., for down or center spread amplitude of 1%, sscAmp = 0.01).
Use the equations below to set up the desired spread spectrum profile.
Note: Make sure MSNA is set up in fractional mode when using the spread spectrum feature. See parameter FBA_INT in register 22.
5.1. Down Spread
For down spread, four spread spectrum parameters need to be written: SSUDP[11:0], SSDN_P1[11:0],
SSDN_P2[14:0], and SSDN_P3[14:0].
Up/Down Parameter:
f PFD
SSUDP  11:0  = Floor  -----------------------------
4  31 500
Intermediate Equation (no register writes):
b
sscAmp
SSDN = 64   a + ---  -----------------------------------------------------------------
c  1 + sscAmp   SSUDP
Down-Spread Parameters:
SSDN_P1  11:0  = Floor  SSDN 
SSDN_P2  14:0  = 32 767   SSDN – SSDN_P1 
SSDN_P3  14:0  = 32 767 = 0x7FFF
Up-Spread Parameters:
SSUP_P1 = 0
SSUP_P2 = 0
SSUP_P3 = 1
8
Rev. 0.6
AN619
5.2. Center Spread
For center spread, seven spread spectrum parameters need to be written: SSUDP[11:0], SSDN_P1[11:0],
SSDN_P2[14:0], SSDN_P3[14:0], SSUP_P1[11:0], SSUP_P2[14:0], and SSUP_P3[14:0].
Up/Down Parameter:
f PFD
SSUDP  11:0  = Floor  -----------------------------
 4  31 500
Intermediate Equations (no register writes):
b
sscAmp
SSUP = 128   a + ---  ----------------------------------------------------------------
c  1 – sscAmp   SSUDP
b
sscAmp
SSDN = 128   a + ---  -----------------------------------------------------------------c
 1 + sscAmp   SSUDP
Up-Spread Parameters:
SSUP_P1  11:0  = Floor  SSUP 
SSUP_P2  14:0  = 32 767   SSUP – SSUP_P1 
SSUP_P3  14:0  = 32 767 = 0x7FFF
Down-Spread Parameters:
SSDN_P1  11:0  = Floor  SSDN 
SSDN_P2  14:0  = 32 767   SSDN – SSDN_P1 
SSDN_P3  14:0  = 32767 = 0x7FFF
5.3. Spread Spectrum Enable Pin (SSEN)
The Spread Spectrum Enable control pin is available on the Si5351A and B devices. Spread spectrum enable
functionality is a logical OR of the SSEN pin and SSC_EN register bit, so for the SSEN pin to work properly, the
SSC_EN register bit must be set to 0.
Rev. 0.6
9
AN619
6. Configuring Initial Phase Offset Register Parameters
Outputs 0-5 of the Si5351 can be programmed with an independent initial phase offset. The phase offset
parameter is an unsigned integer where each LSB represents a phase difference of a quarter of the VCO period,
TVCO/4. Use the equation below to determine the register value.
CLKx_PHOFF  4:0  = Round  DesiredOffset  sec   4  F VCO 
7. Configuring VCXO Parameters (Si5351 B only)
The Si5351B combines free-running clock generation and a VCXO in a single package. The VCXO architecture of
the Si5350B eliminates the need for an external pullable crystal. The “pulling” is done at PLLB. Only a standard,
low cost, fixed-frequency (25 or 27 MHz) AT-cut crystal is required and is used as the reference source for both
PLLA and PLLB.
PLLB must be used as the source for any VCXO output clock. Feedback B Multisynth divider ratio must be set
such that the denominator, c, in the fractional divider a + b/c is fixed to 106. Set VCXO_Param register value
according to the equation below. Note that 1.03 is a margining factor to ensure the full desired pull range is
achieved. For a desired pull-range of +/– 30 ppm, the value APR in the equation below is 30, for +/– 60 ppm APR
is 60, and so on.
b
VCXO_Param[21:0] = 1.03  128a + --------6-  APR
10
10
Rev. 0.6
AN619
8. Si5351 Registers
This section describes the registers and their usage in detail. These values are easily configured using the
ClockBuilder Desktop (see section 3.1.1 ClockbuilderTM Desktop Software in the Si5338 data sheet). See AN428
for a working example using Silicon Labs’ F301 MCU.
8.1. Register Map Summary
The following is a summary of the register map used to read status, control, and configure the Si5351.
Register
7
6
5
4
0
SYS_INIT
LOL_B
LOL_A
LOS
3
1
SYS_INIT_
STKY
LOS_B_
STKY
LOL_A_
STKY
LOS_
STKY
Reserved
2
SYS_INIT_
MASK
LOS_B_
MASK
LOL_A _
MASK
LOS_
MASK
Reserved
3
CLK7_EN
CLK6_EN
CLK5_EN
CLK4_EN
CLK3_EN
4–8
9
1
0
REVID[1:0]
CLK2_EN
CLK1_EN
CLK0_EN
OEB_MASK2
OEB_MASK1
OEB_MASK0
PLLA_SRC
0
0
Reserved
OEB_MASK7
OEB_MASK6
OEB_MASK5
OEB_MASK4
10–14
15
2
Reserved
OEB_MASK3
Reserved
0
0
16
CLK0_PDN
CLKIN_DIV[2:0]
MS0_INT
MS0_SRC
CLK0_INV
CLK0_SRC[1:0]
CLK0_IDRV[1:0]
17
CLK1_PDN
MS1_INT
MS1_SRC
CLK1_INV
CLK1_SRC[1:0]
CLK1_IDRV[1:0]
18
CLK2_PDN
MS2_INT
MS2_SRC
CLK2_INV
CLK2_SRC[1:0]
CLK2_IDRV[1:0]
19
CLK3_PDN
MS3_INT
MS3_SRC
CLK3_INV
CLK3_SRC[1:0]
CLK3_IDRV[1:0]
20
CLK4_PDN
MS4_INT
MS4_SRC
CLK4_INV
CLK4_SRC[1:0]
CLK4_IDRV[1:0]
21
CLK5_PDN
MS5_INT
MS5_SRC
CLK5_INV
CLK5_SRC[1:0]
CLK5_IDRV[1:0]
22
CLK6_PDN
FBA_INT
MS6_SRC
CLK6_INV
CLK6_SRC[1:0]
CLK6_IDRV[1:0]
23
CLK7_PDN
FBB_INT
MS6_SRC
CLK7_INV
CLK7_SRC[1:0]
CLK7_IDRV[1:0]
CLK1_DIS_STATE
CLK0_DIS_STATE
CLK5_DIS_STATE
CLK4_DIS_STATE
24
CLK3_DIS_STATE
CLK2_DIS_STATE
25
CLK7_DIS_STATE
CLK6_DIS_STATE
PLLB_SRC
26
MSNA_P3[15:8]
27
MSNA_P3[7:0]
28
Reserved
29
MSNA_P1[17:16]
MSNA_P1[15:8]
30
MSNA_P1[7:0]
31
MSNA_P3[19:16]
32
MSNA_P2[19:16]
MSNA_P2[15:8]
33
MSNA_P2[7:0]
34
MSNB_P3[15:8]
35
MSNB_P3[7:0]
36
MSNB_P2[17:16]
Reserved
37
MSNB_P1[15:8]
38
MSNB_P1[7:0]
39
MSNB_P3[19:16]
MSNB_P2[19:16]
40
MSNB_P2[15:8]
41
MSNB_P2[7:0]
42
MS0_P3[15:8]
43
44
MS0_P3[7:0]
Reserved
R0_DIV[2:0]
45
46
47
48
MS0_DIVBY4[1:0]
Reserved
MS0_P1[17:16]
MS0_P1[15:8]
MS0_P1[7:0]
MS0_P3[19:16]
MS0_P2[19:16]
MS0_P2[15:8]
Rev. 0.6
11
AN619
Register
7
6
5
4
3
49
MS0_P2[7:0]
50
MS1_P3[15:8]
51
R1_DIV[2:0]
53
MS1_DIVBY4[1:0]
MS1_P3[19:16]
56
MS1_P2[19:16]
MS1_P2[15:8]
57
MS1_P2[7:0]
58
MS2_P3[15:8]
59
MS2_P3[7:0]
60
R2_DIV[2:0]
61
MS2_DIVBY4[1:0]
MS2_P1[7:0]
63
MS2_P3[19:16]
64
MS2_P2[19:16]
MS2_P2[15:8]
65
MS2_P2[7:0]
66
MS3_P3[15:8]
67
MS3_P3[7:0]
68
R3_DIV[2:0]
69
MS3_DIVBY4[1:0]
MS3_P1[17:16]
MS3_P1[15:8]
70
MS3_P1[7:0]
71
MS3_P3[19:16]
72
MS3_P2[19:16]
MS3_P2[15:8]
73
MS3_P2[7:0]
74
MS4_P3[15:8]
75
MS4_P3[7:0]
76
R4_DIV[2:0]
77
MS4_DIVBY4[1:0]
MS4_P1[17:16]
MS4_P1[15:8]
78
MS4_P1[7:0]
79
MS4_P3[19:16]
80
MS4_P2[19:16]
MS4_P2[15:8]
81
MS4_P2[7:0]
82
MS5_P3[15:8]
83
MS5_P3[7:0]
84
R5_DIV[2:0]
85
MS5_DIVBY4[1:0]
MS5_P1[17:16]
MS5_P1[15:8]
86
MS5_P1[7:0]
87
MS5_P3[19:16]
MS5_P2[19:16]
88
MS5_P2[15:8]
89
MS5_P2[7:0]
90
MS6_P1[7:0]
91
MS7_P1[7:0]
92
R7_DIV[2:0]
R6_DIV[2:0]
SSC_EN
SSDN_P2[14:8]
150
SSDN_P2[7:0]
SSC_MODE
SSDN_P3[14:8]
152
SSDN_P3[7:0]
153
12
MS2_P1[17:16]
MS2_P1[15:8]
62
155
MS1_P1[17:16]
MS1_P1[7:0]
55
154
0
MS1_P1[15:8]
54
151
1
MS1_P3[7:0]
52
149
2
SSDN_P1[7:0]
SSUDP[11:8]
SSDN_P1[11:8]
SSUDP[7:0]
Rev. 0.6
AN619
Register
7
6
5
156
4
3
2
157
SSUP_P2[7:0]
158
SSUP_P3[14:8]
159
SSUP_P3[7:0]
160
SS_NCLK[3:0]
162
SSUP_P1[11:8]
VCXO_Param[7:0]
163
VCXO_Param[15:8]
164
Reserved
VCXO_Param[21:16]
165
Reserved
CLK0_PHOFF[6:0]
166
Reserved
CLK1_PHOFF[6:0]
167
Reserved
CLK2_PHOFF[6:0]
168
Reserved
CLK3_PHOFF[6:0]
189
Reserved
CLK4_PHOFF[6:0]
170
Reserved
CLK5_PHOFF[6:0]
171–176
Reserved
PLLB_RST
Reserved
PLLA_RST
Reserved
178–182
183
Reserved
XTAL_CL
Reserved
184–186
187
188-255
0
SSUP_P1[7:0]
161
177
1
SSUP_P2[14:8]
Reserved
CLKIN_FANOUT_EN
XO_FANOUT_EN
Reserved
MS_FANOUT_EN
Reserved
Reserved
Rev. 0.6
13
AN619
9. Register Descriptions
Register 0. Device Status
Bit
D7
D6
D5
D4
Name
SYS_INIT
LOL_B
LOL_A
LOS
Type
R
R
R
R
D3
D2
D1
D0
REVID[1:0]
R
R
R
Reset value = 0000 0000
Bit
7
Name
Function
SYS_INIT System Initialization Status.
During power up the device copies the content of the NVM into RAM and performs a system
initialization. The device is not operational until initialization is complete. It is not recommended to read or write registers in RAM through the I2C interface until initialization is complete. An interrupt will be triggered (INTR pin = 0, Si5351C only) during the system
initialization period.
0: System initialization is complete. Device is ready.
1: Device is in system initialization mode.
6
LOL_B
PLLB Loss Of Lock Status.
Si5351A/C only. PLLB will operate in a locked state when it has a valid reference from CLKIN
or XTAL. A loss of lock will occur if the frequency of the reference clock forces the PLL to
operate outside of its lock range or if the reference clock fails to meet the minimum requirements of a valid input signal as specified in the Si5351 data sheet. An interrupt will be triggered (INTR pin = 0, Si5351C) during a LOL condition.
0: PLL B is locked.
1: PLL B is unlocked. When the device is in this state it will trigger an interrupt causing the
INTR pin to go low (Si5351C only).
5
LOL_A
PLL A Loss Of Lock Status.
PLL A will operate in a locked state when it has a valid reference from CLKIN or XTAL. A loss
of lock will occur if the frequency of the reference clock forces the PLL to operate outside of
its lock range as specified in the data sheet, or if the reference clock fails to meet the minimum requirements of a valid input signal as specified in the Si5351 data sheet. An interrupt
will be triggered (INTR pin = 0, Si5351C only) during a LOL condition.
0: PLL A is operating normally.
1: PLL A is unlocked. When the device is in this state it will trigger an interrupt causing the
INTR pin to go low (Si5351C only).
4
LOS
CLKIN Loss Of Signal (Si5351C Only).
A loss of signal status indicates if the reference clock fails to meet the minimum requirements
of a valid input signal as specified in the Si5351 data sheet. An interrupt will be triggered
(INTR pin = 0, Si5351C only) during a LOS condition.
0: Valid clock signal at the CLKIN pin.
1: Loss of signal detected at the CLKIN pin.
3:0
14
Reserved
Reserved.
Rev. 0.6
AN619
Register 1. Interrupt Status Sticky
Bit
Name
Type
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
SYS_INIT_STKY LOL_B_STKY LOL_A_STKY LOS_STKY
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
7
Name
Function
SYS_INIT_STKY System Calibration Status Sticky Bit.
The SYS_INIT_STKY bit is triggered when the SYS_INIT bit (register 0, bit 7) is triggered high. It remains high until cleared. Writing a 0 to this register bit will cause it to
clear.
0: No SYS_INIT interrupt has occurred since it was last cleared.
1: A SYS_INIT interrupt has occurred since it was last cleared.
6
LOL_B_STKY
PLLB Loss Of Lock Status Sticky Bit.
The LOL_B_STKY bit is triggered when the LOL_B bit (register 0, bit 6) is triggered
high. It remains high until cleared. Writing a 0 to this register bit will cause it to clear.
0: No PLL B interrupt has occurred since it was last cleared.
1: A PLL B interrupt has occurred since it was last cleared.
5
LOL_A_STKY
PLLA Loss Of Lock Status Sticky Bit.
The LOL_A_STKY bit is triggered when the LOL_A bit (register 0, bit 5) is triggered
high. It remains high until cleared. Writing a 0 to this register bit will cause it to clear.
0: No PLLA interrupt has occurred since it was last cleared.
1: A PLLA interrupt has occurred since it was last cleared.
4
LOS_STKY
CLKIN Loss Of Signal Sticky Bit (Si5351C Only).
The LOS_STKY bit is triggered when the LOS bit (register 0, bit 4) is triggered high. It
remains high until cleared. Writing a 0 to this register bit will cause it to clear.
0: No LOS interrupt has occurred since it was last cleared.
1: A LOS interrupt has occurred since it was last cleared.
3:0
Reserved
Leave as default.
Rev. 0.6
15
AN619
Register 2. Interrupt Status Mask
Bit
Name
Type
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
SYS_INIT_MASK LOL_B_MASK LOL_A_MASK LOS_MASK
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
7
Name
Function
SYS_INIT_MASK System Initialization Status Mask.
Use this mask bit to prevent the INTR pin (Si5351C only) from going low when SYS_INIT is asserted.
0: Do not mask the SYS_INIT interrupt.
1: Mask the SYS_INIT interrupt.
6
LOL_B_MASK
PLLB Loss Of Lock Status Mask.
Use this mask bit to prevent the INTR pin (Si5351C only) from going low when LOL_B
is asserted.
0: Do not mask the LOL_B interrupt.
1: Mask the LOL_B interrupt.
5
LOL_A_MASK
PLL A Loss Of Lock Status Mask.
Use this mask bit to prevent the INTR pin (Si5351C only) from going low when LOL_A
is asserted.
0: Do not mask the LOL_A interrupt.
1: Mask the LOL_A interrupt.
4
LOS_MASK
CLKIN Loss Of Signal Mask (Si5351C Only).
Use this mask bit to prevent the INTR pin (Si5351C only) from going low when LOS is
asserted.
0: Do not mask the LOS interrupt.
1: Mask the LOS interrupt.
3:0
16
Reserved
Leave as default.
Rev. 0.6
AN619
Register 3. Output Enable Control
Bit
Name
Type
D7
D6
D5
D4
D3
D2
D1
D0
CLK7_OEB CLK6_OEB CLK5_OEB CLK4_OEB CLK3_OEB CLK2_OEB CLK1_OEB CLK0_OEB
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
D2
D1
D0
Reset value = 0000 0000
Bit
7:0
Name
Function
CLKx_OEB Output Disable for CLKx.
Where x = 0, 1, 2, 3, 4, 5, 6, 7
0: Enable CLKx output.
1: Disable CLKx output.
Register 9. OEB Pin Enable Control Mask
Bit
Name
Type
D7
D6
D5
D4
D3
OEB_MAS OEB_MAS OEB_MAS OEB_MAS OEB_MAS OEB_MAS OEB_MAS OEB_MAS
K7
K6
K5
K4
K3
K2
K1
K0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
7:0
Name
Function
OEB_CLKx OEB pin enable control of CLKx.
Where x = 0, 1, 2, 3, 4, 5, 6, 7
0: OEB pin controls enable/disable state of CLKx output.
1: OEB pin does not control enable/disable state of CLKx output.
Rev. 0.6
17
AN619
Register 15. PLL Input Source
Bit
Name
Type
D7
D6
D5
D4
CLKIN_DIV[1:0]
R/W
R/W
D3
D2
D1
D0
R/W
R/W
PLLB_SRC PLLA_SRC
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
7:6
Name
Function
CLKIN_DIV[1: ClKIN Input Divider.
0]
Valid PLL input range is 10-40 MHz. If CLKIN is > 40 MHz, CLKIN input divider,
CLKIN_DIV, must be used to bring the PLL input within the 10-40 MHz range.
00b: Divide by 1.
01b: Divide by 2.
10b: Divide by 4.
11b: Divide by 8.
5:4
Reserved
3
PLLB_SRC
Input Source Select for PLLB.
0: Select the XTAL input as the reference clock for PLLB.
1: Select the CLKIN input as the reference clock for PLLB (Si5351C only).
2
PLLA_SRC
Input Source Select for PLLA.
0: Select the XTAL input as the reference clock for PLLA.
1: Select the CLKIN input as the reference clock for PLLA (Si5351C only).
1:0
Reserved
18
Leave as default.
Leave as default.
Rev. 0.6
AN619
Register 16. CLK0 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK0_PDN
MS0_INT
MS0_SRC
CLK0_INV
CLK0_SRC[1:0]
CLK0_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK0_PDN
Function
Clock 0 Power Down.
This bit allows powering down the CLK0 output driver to conserve power when the output is unused.
0: CLK0 is powered up.
1: CLK0 is powered down.
6
MS0_INT
MultiSynth 0 Integer Mode.
This bit can be used to force MS0 into Integer mode to improve jitter performance. Note
that the fractional mode is necessary when a delay offset is specified for CLK0.
0: MS0 operates in fractional division mode.
1: MS0 operates in integer mode.
5
MS0_SRC
MultiSynth Source Select for CLK0.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth0.
4
CLK0_INV
Output Clock 0 Invert.
0: Output Clock 0 is not inverted.
1: Output Clock 0 is inverted.
3:2
CLK0_SRC[1:0] Output Clock 0 Input Source.
These bits determine the input source for CLK0.
00: Select the XTAL as the clock source for CLK0. This option by-passes both synthesis
stages (PLL/VCXO & MultiSynth) and connects CLK0 directly to the oscillator which
generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK0. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK0 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Reserved. Do not select this option.
11: Select MultiSynth 0 as the source for CLK0. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK0_IDRV[1:0] CLK0 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
Rev. 0.6
19
AN619
Register 17. CLK1 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK1_PDN
MS1_INT
MS1_SRC
CLK1_INV
CLK1_SRC[1:0]
CLK1_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK1_PDN
Function
Clock 1 Power Down.
This bit allows powering down the CLK1 output driver to conserve power when the output is unused.
0: CLK1 is powered up.
1: CLK1 is powered down.
6
MS1_INT
MultiSynth 1 Integer Mode.
When the MS1 divider is an even integer, this bit can be used to force MS1 into integer
mode to improve jitter performance. Not valid for odd integers. Note that the fractional
mode is necessary when a delay offset is specified for CLK1.
0: MS1 operates in fractional division mode.
1: MS1 operates in integer mode.
5
MS1_SRC
MultiSynth Source Select for CLK1.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth0.
4
CLK1_INV
Output Clock 1 Invert.
0: Output Clock 1 is not inverted.
1: Output Clock 1 is inverted.
3:2
CLK1_SRC[1:0] Output Clock 1 Input Source.
These bits determine the input source for CLK1.
00: Select the XTAL as the clock source for CLK1. This option by-passes both synthesis
stages (PLL/VCXO & MultiSynth) and connects CLK1 directly to the oscillator which
generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK1. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK1 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Select Multisynth 0 as the source for CLK1.
11: Select MultiSynth 1 as the source for CLK1. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK1_IDRV[1:0] CLK1 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
20
Rev. 0.6
AN619
Register 18. CLK2 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK2_PDN
MS2_INT
MS2_SRC
CLK2_INV
CLK2_SRC[1:0]
CLK2_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK2_PDN
Function
Clock 2 Power Down.
This bit allows powering down the CLK2 output driver to conserve power when the output is unused.
0: CLK2 is powered up.
1: CLK2 is powered down.
6
MS2_INT
MultiSynth 2 Integer Mode.
When the MS2 divider is an even integer, this bit can be used to force MS2 into integer
mode to improve jitter performance. Not valid for odd integers. Note that the fractional
mode is necessary when a delay offset is specified for CLK2.
0: MS2 operates in fractional division mode.
1: MS2 operates in integer mode.
5
MS2_SRC
MultiSynth Source Select for CLK2.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth2.
4
CLK2_INV
Output Clock 2 Invert.
0: Output Clock 2 is not inverted.
1: Output Clock 2 is inverted.
3:2
CLK2_SRC[1:0] Output Clock 2 Input Source.
These bits determine the input source for CLK2.
00: Select the XTAL as the clock source for CLK2. This option by-passes both synthesis
stages (PLL/VCXO & MultiSynth) and connects CLK2 directly to the oscillator which generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK2. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK2 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Select Multisynth 0 as the source for CLK2.
11: Select MultiSynth 2 as the source for CLK2. Select this option when using the Si5351
to generate free-running or synchronous clocks.
1:0
CLK2_IDRV[1:0] CLK2 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
Rev. 0.6
21
AN619
Register 19. CLK3 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK3_PDN
MS3_INT
MS3_SRC
CLK3_INV
CLK3_SRC[1:0]
CLK3_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK3_PDN
Function
Clock 3 Power Down.
This bit allows powering down the CLK3 output driver to conserve power when the output is unused.
0: CLK3 is powered up.
1: CLK3 is powered down.
6
MS3_INT
MultiSynth 3 Integer Mode.
When the MS3 divider is an even integer, this bit can be used to force MS3 into integer
mode to improve jitter performance. Not valid for odd integers. Note that the fractional
mode is necessary when a delay offset is specified for CLK3.
0: MS3 operates in fractional division mode.
1: MS3 operates in integer mode.
5
MS3_SRC
MultiSynth Source Select for CLK3.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth3.
4
CLK3_INV
Output Clock 3 Invert.
0: Output Clock 3 is not inverted.
1: Output Clock 3 is inverted.
3:2
CLK3_SRC[1:0] Output Clock 3 Input Source.
These bits determine the input source for CLK3.
00: Select the XTAL as the clock source for CLK3. This option by-passes both synthesis changes (PCL/VCXO and Multisynth) and connects CLK3 directly to the oscillator
which generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK3. This by-passes both synthesis stages
(PLL/VCXO and Multisynth) and connects CLK3 directly to the CLKIN input. This
essentially creates a buffered output of the CLKIN input.
10: Select Multisynth 0 as the source for CLK3.
11: Select Multisynth 3 as the source for CLK3. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK3_IDRV[1:0] CLK3 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
22
Rev. 0.6
AN619
Register 20. CLK4 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK4_PDN
MS4_INT
MS4_SRC
CLK4_INV
CLK4_SRC[1:0]
CLK4_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK4_PDN
Function
Clock 4 Power Down.
This bit allows powering down the CLK4 output driver to conserve power when the output is unused.
0: CLK4 is powered up.
1: CLK4 is powered down.
6
MS4_INT
MultiSynth 4 Integer Mode.
When the MS4 divider is an even integer, this bit can be used to force MS4 into integer
mode to improve jitter performance. Not valid for odd integers. Note that the fractional
mode is necessary when a delay offset is specified for CLK4.
0: MS4 operates in fractional division mode.
1: MS4 operates in integer mode.
5
MS4_SRC
MultiSynth Source Select for CLK4.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth4.
4
CLK4_INV
Output Clock 4 Invert.
0: Output Clock 4 is not inverted.
1: Output Clock 4 is inverted.
3:2
CLK4_SRC[1:0] Output Clock 4 Input Source.
These bits determine the input source for CLK4.
00: Select the XTAL as the clock source for CLK4. This option by-passes both synthesis stages (PLL/VCXO & MultiSynth) and connects CLK4 directly to the oscillator
which generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK4. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK4 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Reserved. Do not select this option.
11: Select MultiSynth 4 as the source for CLK4. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK4_IDRV[1:0] CLK4 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
Rev. 0.6
23
AN619
Register 21. CLK5 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK5_PDN
MS5_INT
MS5_SRC
CLK5_INV
CLK5_SRC[1:0]
CLK5_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK5_PDN
Function
Clock 5 Power Down.
This bit allows powering down the CLK5 output driver to conserve power when the output is unused.
0: CLK4 is powered up.
1: CLK4 is powered down.
6
MS5_INT
MultiSynth 5 Integer Mode.
When the MS5 divider is an even integer, this bit can be used to force MS5 into integer
mode to improve jitter performance. Not valid for odd integers. Note that the fractional
mode is necessary when a delay offset is specified for CLK5.
0: MS5 operates in fractional division mode.
1: MS5 operates in integer mode.
5
MS5_SRC
MultiSynth Source Select for CLK5.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth5.
4
CLK5_INV
Output Clock 5 Invert.
0: Output Clock 5 is not inverted.
1: Output Clock 5 is inverted.
3:2
CLK5_SRC[1:0] Output Clock 5 Input Source.
These bits determine the input source for CLK5.
00: Select the XTAL as the clock source for CLK5. This option by-passes both synthesis stages (PLL/VCXO & MultiSynth) and connects CLK5 directly to the oscillator
which generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK5. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK5 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Select Multisynth 4 as the source for CLK5.
11: Select MultiSynth 5 as the source for CLK5. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK5_IDRV[1:0] CLK5 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
24
Rev. 0.6
AN619
Register 22. CLK6 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK6_PDN
FBA_INT
MS6_SRC
CLK6_INV
CLK6_SRC[1:0]
CLK6_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK6_PDN
Function
Clock 7 Power Down.
This bit allows powering down the CLK6 output driver to conserve power when the output is unused.
0: CLK6 is powered up.
1: CLK6 is powered down.
6
FBA_INT
FBA MultiSynth Integer Mode.
This bit can be used to force Feedback A Multisynth into Integer mode to improve jitter
performance. Note that the fractional mode is necessary when spread spectrum is
specified for any output clocks.
0: MSNA operates in fractional division mode.
1: MSNA operates in integer mode.
5
MS6_SRC
MultiSynth Source Select for CLK6.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth6.
4
CLK6_INV
Output Clock 6 Invert.
0: Output Clock 6 is not inverted.
1: Output Clock 6 is inverted.
3:2
CLK6_SRC[1:0] Output Clock 0 Input Source.
These bits determine the input source for CLK6.
00: Select the XTAL as the clock source for CLK6. This option by-passes both synthesis stages (PLL/VCXO & MultiSynth) and connects CLK6 directly to the oscillator
which generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK6. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK6 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Select Multisynth 4 as the source for CLK6.
11: Select MultiSynth 6 as the source for CLK6. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK6_IDRV[1:0] CLK6 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
Rev. 0.6
25
AN619
Register 23. CLK7 Control
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK7_PDN
FBB_INT
MS7_SRC
CLK7_INV
CLK7_SRC[1:0]
CLK7_IDRV[1:0]
Type
R/W
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
CLK7_PDN
Function
Clock 7 Power Down.
This bit allows powering down the CLK7 output driver to conserve power when the output is unused.
0: CLK7 is powered up.
1: CLK7 is powered down.
6
FBB_INT
FBB MultiSynth Integer Mode.
This bit can be used to force Feedback B into Integer mode to improve jitter performance.
0: MSNB operates in fractional division mode.
1: MSNB operates in integer mode.
5
MS7_SRC
MultiSynth Source Select for CLK7.
0: Select PLLA as the source for MultiSynth0.
1: Select PLLB (Si5351A/C only) or VCXO (Si5351B only) MultiSynth0.
4
CLK7_INV
Output Clock 7 Invert.
0: Output Clock 7 is not inverted.
1: Output Clock 7 is inverted.
3:2
CLK7_SRC[1:0] Output Clock 0 Input Source.
These bits determine the input source for CLK7.
00: Select the XTAL as the clock source for CLK7. This option by-passes both synthesis stages (PLL/VCXO & MultiSynth) and connects CLK7 directly to the oscillator
which generates an output frequency determined by the XTAL frequency.
01: Select CLKIN as the clock source for CLK7. This by-passes both synthesis stages
(PLL/VCXO & MultiSynth) and connects CLK7 directly to the CLKIN input. This essentially creates a buffered output of the CLKIN input.
10: Select Multisynth 4 as the source for CLK7.
11: Select MultiSynth 7 as the source for CLK7. Select this option when using the
Si5351 to generate free-running or synchronous clocks.
1:0
CLK7_IDRV[1:0] CLK7 Output Rise and Fall time / Drive Strength Control.
00: 2 mA
01: 4 mA
10: 6 mA
11: 8 mA
26
Rev. 0.6
AN619
Register 24. CLK3–0 Disable State
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK3_DIS_STATE
CLK2_DIS_STATE
CLK1_DIS_STATE
CLK0_DIS_STATE
Type
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
Function
7:0
CLKx_DIS_STATE
Clock x Disable State.
Where x = 0, 1, 2, 3. These 2 bits determine the state of the CLKx output when disabled. Individual output clocks can be disabled using register Output Enable Control located at address 3. Outputs are also disabled using the OEB pin.
00: CLKx is set to a LOW state when disabled.
01: CLKx is set to a HIGH state when disabled.
10: CLKx is set to a HIGH IMPEDANCE state when disabled.
11: CLKx is NEVER DISABLED.
Register 25. CLK7–4 Disable State
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Name
CLK7_DIS_STATE
CLK6_DIS_STATE
CLK5_DIS_STATE
CLK4_DIS_STATE
Type
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7:0
CLKx_DIS_STATE
Function
Clock x Disable State.
Where x = 4, 5, 6, 7. These 2 bits determine the state of the CLKx output when disabled. Individual output clocks can be disabled using register Output Enable Control located at address 3. Outputs are also disabled using the OEB pin.
00: CLKx is set to a LOW state when disabled.
01: CLKx is set to a HIGH state when disabled.
10: CLKx is set to a HIGH IMPEDANCE state when disabled.
11: CLKx is NEVER DISABLED.
Rev. 0.6
27
AN619
Register 26. Multisynth NA Parameters
Bit
D7
D6
D5
D4
D3
D2
Name
MSNA_P3[15:8]
Type
R/W
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNA_P3[15:8]
Function
Multisynth NA Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the PLLA Feedback Multisynth Divider.
Register 27. Multisynth NA Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNA_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNA_P3[7:0]
Function
Multisynth NA Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the PLLA Feedback Multisynth Divider.
Register 28. Multisynth NA Parameters
Bit
D7
Name
D6
D5
D4
D3
Unused
D2
Reserved
Type
D1
D0
MSNA_P1[17:16]
R/W
Reset value = xxxx xxxx
Bit
7:4
Name
Unused
3:2
Reserved
Function
Unused.
Reserved.
Leave as default, 0.
1:0
MSNA_P1[17:16]
Multisynth NA Parameter 1.
This 18-bit number is an encoded representation of the integer part of the PLLA
Feedback Multisynth divider.
28
Rev. 0.6
AN619
Register 29. Multisynth NA Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNA_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNA_P1[15:8]
Function
Multisynth NA Parameter 1.
This 18-bit number is an encoded representation of the integer part of the PLLA
Feedback Multisynth divider.
Register 30. Multisynth NA Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNA_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNA_P1[7:0]
Function
Multisynth NA Parameter 1.
This 18-bit number is an encoded representation of the integer part of the PLLA
Feedback Multisynth divider.
Register 31. Multisynth NA Parameters
Bit
D7
Name
D6
D5
D4
D3
MSNA_P3[19:16]
D2
D1
D0
MSNA_P2[19:16]
Type
R/W
Reset value = xxxx xxxx
Bit
7:4
Name
MSNA_P3[19:16]
Function
Multisynth NA Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the PLLA Feedback Multisynth divider.
3:0
MSNA_P2[19:16]
Multisynth NA Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the PLLA Feedback Multisynth divider.
Rev. 0.6
29
AN619
Register 32. Multisynth NA Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNA_P2[15:18]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNA_P2[15:18]
Function
Multisynth NA Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the PLLA Feedback Multisynth divider.
Register 33. Multisynth NA Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNA_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNA_P2[7:0]
Function
Multisynth NA Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the PLLA Feedback Multisynth divider.
Register 34. Multisynth NB Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNB_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNB_P3[15:8]
Function
Multisynth NA Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the PLLA Feedback Multisynth divider.
30
Rev. 0.6
AN619
Register 35. Multisynth NB Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNB_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNB_P3[7:0]
Function
Multisynth NB Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the PLLB Feedback Multisynth divider.
Register 36. Multisynth NB Parameters
Bit
D7
D6
Name
D5
D4
D3
Unused
D2
Reserved
Type
D1
D0
MSNB_P1[17:16]
R/W
Reset value = xxxx xxxx
Bit
7:4
Name
3:2
Reserved
Function
Reserved
Reserved.
Leave as default, 0.
1:0
MSNB_P1[17:16]
Multisynth NB Parameter 1.
This 18-bit number is an encoded representation of the integer part for the fractional part of the PLLB Feedback Multisynth divider.
Register 37. Multisynth NB Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNB_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNB_P1[15:8]
Function
Multisynth NB Parameter 1.
This 18-bit number is an encoded representation of the integer part of the PLLB
Feedback Multisynth divider.
Rev. 0.6
31
AN619
Register 38. Multisynth NB Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNB_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MSNB_P1[7:0]
Function
Multisynth NB Parameter 1.
This 18-bit number is an encoded representation of the integer part of the PLLB
Feedback Multisynth divider.
Register 39. Multisynth NB Parameters
Bit
D7
Name
D6
D5
D4
D3
MSNB_P3[19:16]
D2
D1
D0
MSNB_P2[19:16]
Type
R/W
Reset value = xxxx xxxx
Bit
7:4
Name
MSNB_P3[19:16]
3:0
MSNB_P2[19:16]
Function
Multisynth NB Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the PLLB Feedback Multisynth divider.
Multisynth NB Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the PLLB Feedback Multisynth divider.
Register 40. Multisynth NB Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNB_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
32
Name
MSNB_P2[15:8]
Function
Multisynth NB Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the PLLB Feedback Multisynth divider.
Rev. 0.6
AN619
Register 41. Multisynth NB Parameters
Bit
D7
D6
D5
D4
D3
Name
MSNB_P2[7:0]
Type
R/W
Bit
7:0
Name
MSNB_P2[7:0]
D2
D1
D0
Function
Multisynth NB Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the PLLB Feedback Multisynth divider.
Register 42. Multisynth0 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS0_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
7:0
Name
MS0_P3[15:8]
Function
Multisynth0 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth0 Divider.
Register 43. Multisynth0 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS0_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS0_P3[7:0]
Function
Multisynth0 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth0 Divider.
Rev. 0.6
33
AN619
Register 44. Multisynth0 Parameters
Bit
D7
D6
Name
Type
D5
D4
D3
R0_DIV[2:0]
R/W
D2
MS0_DIVBY4[1:0]
R/W
R/W
D1
D0
MS0_P1[17:16]
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:4
R0_DIV[2:0]
Function
R0 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3:2
1:0
MS0_DIVBY4[1:0] MS0 Divide by 4 Enable.
11: Divide by 4 enabled.
00: Divide by a value other than 4.
MS0_P1[17:16]
Multisynth0 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the MultiSynth0 divider.
Register 45. Multisynth0 Parameters
Bit
D7
Name
D6
D5
D4
D3
D2
D1
D0
MS0_P1[15:8]
Type
Reset value = xxxx xxxx
Bit
Name
7:0
MS0_P1[15:8]
R/W
Function
Multisynth0 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the MultiSynth1 divider.
34
Rev. 0.6
AN619
Register 46. Multisynth0 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS0_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS0_P1[7:0]
Function
Multisynth0 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the MultiSynth1 divider.
Register 47. Multisynth0 Parameters
Bit
D7
D6
D5
D4
D3
D2
D1
Name
MS0_P3[19:16]
MS0_P2[19:16]
Type
R/W
R/W
D0
Reset value = xxxx xxxx
Bit
Name
7:4
MS0_P3[19:16]
Function
Multisynth0 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth0 Divider
3:0
MS0_P2[19:16]
Multisynth0 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth1 Divider.
Register 48. Multisynth0 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS0_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS0_P2[15:8]
Function
Multisynth0 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth1 Divider.
Rev. 0.6
35
AN619
Register 49. Multisynth0 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS0_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS0_P2[7:0]
Function
Multisynth0 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth1 Divider.
Register 50. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS1_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS1_P3[15:8]
Function
Multisynth1 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth1 Divider.
Register 51. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS1_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS1_P3[7:0]
Function
Multisynth1 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth1 Divider.
36
Rev. 0.6
AN619
Register 52. Multisynth1 Parameters
Bit
D7
D6
D4
D3
R1_DIV[2:0]
Name
Type
D5
R/W
D2
MS1_DIVBY4[1:0]
R/W
R/W
D1
D0
MS1_P1[17:16]
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:4
R1_DIV[2:0]
Function
R1 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3:2
1:0
MS1_DIVBY4[1:0] MS1 Divide by 4 Enable.
11: Divide by 4 enabled.
00: Divide by a value other than 4.
MS1_P1[17:16]
Multisynth1 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the MultiSynth1 divider.
Register 53. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS1_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS1_P1[15:8]
Function
Multisynth1 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the MultiSynth1 divider.
Rev. 0.6
37
AN619
Register 54. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS1_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS1_P1[7:0]
Function
Multisynth1 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the MultiSynth1 divider.
Register 55. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
D2
D1
Name
MS1_P3[19:16]
MS1_P2[19:16]
Type
R/W
R/W
D0
Reset value = xxxx xxxx
Bit
Name
7:4
MS1_P3[19:16]
Function
Multisynth1 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth1 Divider
3:0
MS1_P2[19:16]
Multisynth1 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth1 Divider.
Register 56. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS1_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS1_P2[15:8]
Function
Multisynth1 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth1 divider.
38
Rev. 0.6
AN619
Register 57. Multisynth1 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS1_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS1_P2[7:0]
Function
Multisynth1 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth1 divider.
Register 58. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS2_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS2_P3[15:8]
Function
Multisynth2 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth2 divider.
Register 59. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS2_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS2_P3[7:0]
Function
Multisynth2 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the MultiSynth2 divider.
Rev. 0.6
39
AN619
Register 60. Multisynth2 Parameters
Bit
D7
D6
Name
Type
D5
D4
D3
R2_DIV[2:0]
R/W
D2
MS2_DIVBY4[1:0]
R/W
R/W
D1
D0
MS2_P1[17:16]
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:4
R2_DIV[2:0]
Function
R2 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3:2
1:0
MS2_DIVBY4[1:0] MS2 Divide by 4 Enable.
11: Divide by 4 enabled.
00: Divide by a value other than 4.
MS2_P1[17:16]
Multisynth2 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth2 divider.
Register 61. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS2_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS2_P1[15:8]
Function
Multisynth2 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth2 divider.
40
Rev. 0.6
AN619
Register 62. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS2_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS2_P1[7:0]
Function
Multisynth2 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth2 divider.
Register 63. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
D2
D1
Name
MS2_P3[19:16]
MS2_P2[19:16]
Type
R/W
R/W
D0
Reset value = xxxx xxxx
Bit
Name
7:4
MS2_P3[19:16]
Function
Multisynth2 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth2 divider
3:0
MS2_P2[19:16]
Multisynth2 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth2 divider.
Register 64. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS2_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS2_P2[15:8]
Function
Multisynth2 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth2 divider.
Rev. 0.6
41
AN619
Register 65. Multisynth2 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS2_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS2_P2[7:0]
Function
Multisynth2 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth2 divider.
Register 66. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS3_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS3_P3[15:8]
Function
Multisynth3 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth3 divider.
Register 67. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS3_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS3_P3[7:0]
Function
Multisynth3 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth3 divider.
42
Rev. 0.6
AN619
Register 68. Multisynth3 Parameters
Bit
D7
D6
Name
Type
D5
D4
D3
R3_DIV[2:0]
R/W
D2
MS3_DIVBY4[1:0]
R/W
R/W
D1
D0
MS3_P1[17:16]
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:4
R3_DIV[2:0]
Function
R3 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3:2
1:0
MS3_DIVBY4[1:0] MS3 Divide by 4 Enable.
11: Divide by 4 enabled.
00: Divide by a value other than 4.
MS3_P1[17:16]
Multisynth3 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth3 divider.
Register 69. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS3_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS3_P1[15:8]
Function
Multisynth3 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth3 divider.
Rev. 0.6
43
AN619
Register 70. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS3_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS3_P1[7:0]
Function
Multisynth3 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth3 divider.
Register 71. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
D2
D1
Name
MS3_P3[19:16]
MS3_P2[19:16]
Type
R/W
R/W
D0
Reset value = xxxx xxxx
Bit
Name
7:4
MS3_P3[19:16]
Function
Multisynth3 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth3 divider
3:0
MS3_P2[19:16]
Multisynth3 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth3 divider.
Register 72. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS3_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS3_P2[15:8]
Function
Multisynth3 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth3 divider.
44
Rev. 0.6
AN619
Register 73. Multisynth3 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS3_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS3_P2[7:0]
Function
Multisynth3 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth3 divider.
Register 74. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS4_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS4_P3[15:8]
Function
Multisynth4 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth4 divider.
Register 75. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS4_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS4_P3[7:0]
Function
Multisynth4 Parameter 3.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth4 divider.
Rev. 0.6
45
AN619
Register 76. Multisynth4 Parameters
Bit
D7
D6
Name
Type
D5
D4
D3
R4_DIV[2:0]
R/W
D2
MS4_DIVBY4[1:0]
R/W
R/W
D1
D0
MS4_P1[17:16]
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:4
R4_DIV[2:0]
Function
R4 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3:2
1:0
MS4_DIVBY4[1:0] MS4 Divide by 4 Enable.
11: Divide by 4 enabled.
00: Divide by a value other than 4.
MS4_P1[17:16]
Multisynth4 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth4 divider.
Register 77. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS4_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS4_P1[15:8]
Function
Multisynth4 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth4 divider.
46
Rev. 0.6
AN619
Register 78. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS4_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS4_P1[7:0]
Function
Multisynth4 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth4 divider.
Register 79. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
D2
D1
Name
MS4_P3[19:16]
MS4_P2[19:16]
Type
R/W
R/W
D0
Reset value = xxxx xxxx
Bit
Name
7:4
MS4_P3[19:16]
Function
Multisynth4 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth4 divider
3:0
MS4_P2[19:16]
Multisynth4 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth4 divider.
Register 80. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS4_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS4_P2[15:8]
Function
Multisynth4 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth4 Divider.
Rev. 0.6
47
AN619
Register 81. Multisynth4 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS4_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS4_P2[7:0]
Function
Multisynth4 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth4 divider.
Register 82. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS5_P3[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS5_P3[15:8]
Function
Multisynth5 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth5 divider.
Register 83. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS5_P3[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS5_P3[7:0]
Function
Multisynth5 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth5 divider.
48
Rev. 0.6
AN619
Register 84. Multisynth5 Parameters
Bit
D7
D6
Name
Type
D5
D4
D3
R5_DIV[2:0]
R/W
D2
MS5_DIVBY4[1:0]
R/W
R/W
D1
D0
MS5_P1[17:16]
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:4
R5_DIV[2:0]
Function
R5 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3:2
1:0
MS5_DIVBY4[1:0] MS5 Divide by 4 Enable.
11: Divide by 4 enabled.
00: Divide by a value other than 4.
MS5_P1[17:16]
Multisynth5 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth5 divider.
Register 85. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS5_P1[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS5_P1[15:8]
Function
Multisynth5 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth5 divider.
Rev. 0.6
49
AN619
Register 86. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS5_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS5_P1[7:0]
Function
Multisynth5 Parameter 1.
This 18-bit number is an encoded representation of the integer part of the Multisynth5 divider.
Register 87. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
D2
D1
Name
MS5_P3[19:16]
MS5_P2[19:16]
Type
R/W
R/W
D0
Reset value = xxxx xxxx
Bit
Name
7:4
MS5_P3[19:16]
Function
Multisynth5 Parameter 3.
This 20-bit number is an encoded representation of the denominator for the fractional part of the Multisynth5 divider
3:0
MS5_P2[19:16]
Multisynth5 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the MultiSynth5 divider.
Register 88. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS5_P2[15:8]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS5_P2[15:8]
Function
Multisynth5 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth5 Divider.
50
Rev. 0.6
AN619
Register 89. Multisynth5 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS5_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS5_P2[7:0]
Function
Multisynth5 Parameter 2.
This 20-bit number is an encoded representation of the numerator for the fractional
part of the Multisynth5 Divider.
Register 90. Multisynth6 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS6_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS6_P1[7:0]
Function
Multisynth6 Parameter 1.
This 8-bit number is the Multisynth6 divide ratio. Multisynth6 divide ratio can only be
even integers greater than or equal to 6. All other divide values are invalid.
Register 91. Multisynth7 Parameters
Bit
D7
D6
D5
D4
D3
Name
MS7_P1[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
MS7_P1[7:0]
Function
Multisynth7 Parameter 1.
This 8-bit number is the Multisynth6 divide ratio. Multisynth6 divide ratio can only be
even integers greater than or equal to 6. All other divide values are invalid.
Rev. 0.6
51
AN619
Register 92. Clock 6 and 7 Output Divider
Bit
D7
Name
Type
D6
D5
D4
D3
R7_DIV[2:0]
R/W
Name
7
Reserved
6:4
R7_DIV[2:0]
R/W
R/W
Function
Leave as default.
R7 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
3
Reserved
1:0
R6_DIV[2:0]
Leave as default.
R6 Output Divider.
000b: Divide by 1
001b: Divide by 2
010b: Divide by 4
011b: Divide by 8
100b: Divide by 16
101b: Divide by 32
110b: Divide by 64
111b: Divide by 128
52
D1
R6_DIV[2:0]
Reset value = xxxx xxxx
Bit
D2
Rev. 0.6
R/W
D0
AN619
Register 149. Spread Spectrum Parameters
Bit
D7
Name
SSC_EN
D6
D5
D4
D3
D2
D1
D0
SSDN_P2[14:8]
R/W
Type
Reset value = xxxx xxxx
Bit
Name
7
SSC_EN
Function
Spread Spectrum Enable
1: Enable
0: Disable
Note: Spread Spectrum Enable control pin is available on the Si5351A and B devices. Spread
spectrum enable functionality is a logical OR of the SSEN pin and SSC_EN register bit,
so for the SSEN pin to work properly, this register bit must be set to 0.
6:0
SSDN_P2[14:8]
PLL A Spread Spectrum Down Parameter 2.
Register 150. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSDN_P2[7:0]
Type
R/W
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
SSDN_P2[7:0]
Function
PLL A Spread Spectrum Down Parameter 2.
Register 151. Spread Spectrum Parameters
Bit
D7
Name
SSC_MODE
D6
D5
D4
D3
D2
D1
D0
SSDN_P3[14:8]
R/W
Type
Reset value = xxxx xxxx
Bit
Name
7
SSC_MODE
6:0
SSDN_P3[14:8]
Function
Spread Spectrum Mode.
0: Down Spread
1: Center Spread
PLL A Spread Spectrum Down Parameter 3.
Rev. 0.6
53
AN619
Register 152. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSDN_P3[7:0]
Type
R/W
D2
D1
D0
D2
D1
D0
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
SSDN_P3[7:0]
Function
PLL A Spread Spectrum Down Parameter 3.
Register 153. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSDN_P1[7:0]
Type
R/W
Reset value = xxxx xxxx
Bit
Name
7:0
SSDN_P1[7:0]
Function
PLL A Spread Spectrum Down Parameter 1.
Register 154. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
SSUDP[11:8]
Name
SSDN_P1[11:8]
R/W
Type
Reset value = xxxx xxxx
Bit
Name
7:4
SSUDP[11:8]
3:0
SSDN_P1[11:8]
Function
PLL A Spread Spectrum Up/Down Parameter.
PLL A Spread Spectrum Down Parameter 1.
Register 155. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSUDP[7:0]
Type
R/W
Reset value = xxxx xxxx
Bit
Name
7:0
SSUDP[7:0]
54
Function
PLL A Spread Spectrum Up/Down Parameter.
Rev. 0.6
D2
D1
D0
AN619
Register 156. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSUP_P2[14:8]
Type
R/W
D2
D1
D0
D2
D1
D0
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:0
SSUP_P2[14:8]
Function
Unused.
PLL A Spread Spectrum Up Parameter 2.
Register 157. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSUP_P2[7:0]
Type
R/W
Reset value = xxxx xxxx
Bit
Name
7:0
SSUP_P2[7:0]
Function
PLL A Spread Spectrum Up Parameter 2.
Register 158. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSUP_P3[14:8]
Type
R/W
Reset value = xxxx xxxx
Bit
Name
7
Unused
6:0
SSUP_P3[14:8]
Function
Unused.
PLL A Spread Spectrum Up Parameter 3.
Rev. 0.6
55
AN619
Register 159. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSUP_P3[7:0]
Type
R/W
D2
D1
D0
D2
D1
D0
D2
D1
D0
Reset value = xxxx xxxx
Bit
Name
7:0
SSUP_P3[7:0]
Function
PLL A Spread Spectrum Up Parameter 3.
Register 160. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
Name
SSUP_P1[7:0]
Type
R/W
Reset value = xxxx xxxx
Bit
Name
7:0
SSUP_P1[7:0]
Function
PLL A Spread Spectrum Up Parameter 1.
Register 161. Spread Spectrum Parameters
Bit
D7
D6
D5
D4
D3
SS_NCLK[3:0]
Name
SSUP_P1[11:8]
R/W
Type
Reset value = xxxx xxxx
Bit
Name
Function
7:4
SS_NCLK[3:0]
Must write 0000b to these bits.
3:0
SSUP_P1[11:8]
PLL A Spread Spectrum Up Parameter 1.
Register 162. VCXO Parameter
Bit
D7
D6
D5
D4
D3
Name
VCXO_Param[7:0]
Type
R/W
Reset value = xxxx xxxx
Bit
7:0
56
Name
Function
VCXO_Param[7:0] VCXO Parameter.
Rev. 0.6
D2
D1
D0
AN619
Register 163. VCXO Parameter
Bit
D7
D6
D5
D4
D3
Name
VCXO_Param[15:8]
Type
R/W
D2
D1
D0
D2
D1
D0
D2
D1
D0
R/W
R/W
R/W
Reset value = xxxx xxxx
Bit
7:0
Name
Function
VCXO_Param[15:8] VCXO Parameter.
Register 164. VCXO Parameter
Bit
D7
D6
D5
D4
D3
Name
VCXO_Param[21:16]
Type
R/W
Reset value = xxxx xxxx
Bit
Name
7:6
Reserved
5:0
Function
Reserved. Only write 00b to these bits.
VCXO_Param[21:16] VCXO Parameter.
Register 165. CLK0 Initial Phase Offset
Bit
D7
D6
D5
D4
CLK0_PHOFF[6:0]
Name
Type
D3
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
Reserved
6:0
Function
Only write 0 to this bit.
CLK0_PHOFF[6:0] Clock 0 Initial Phase Offset.
CLK0_PHOFF[6:0] is an unsigned integer with one LSB equivalent to a time delay of
Tvco/4, where Tvco is the period of the VCO/PLL associated with this output.
Rev. 0.6
57
AN619
Register 166. CLK1 Initial Phase Offset
Bit
D7
D6
D5
D4
D2
D1
D0
R/W
R/W
R/W
CLK1_PHOFF[6:0]
Name
Type
D3
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
Reserved
6:0
Function
Only write 0 to this bit.
CLK1_PHOFF[6:0] Clock 1 Initial Phase Offset.
CLK1_PHOFF[6:0] is an unsigned integer with one LSB equivalent to a time delay of
Tvco/4, where Tvco is the period of the VCO/PLL associated with this output.
Register 167. CLK2 Initial Phase Offset
Bit
D7
D6
D5
D4
D2
D1
D0
R/W
R/W
R/W
CLK2_PHOFF[6:0]
Name
Type
D3
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
Reserved
6:0
Function
Only write 0 to this bit.
CLK2_PHOFF[6:0] Clock 2 Initial Phase Offset.
CLK2_PHOFF[6:0] is an unsigned integer with one LSB equivalent to a time delay of
Tvco/4, where Tvco is the period of the VCO/PLL associated with this output.
Register 168. CLK3 Initial Phase Offset
Bit
D7
D6
D5
D4
D2
D1
D0
R/W
R/W
R/W
CLK3_PHOFF[6:0]
Name
Type
D3
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
Reserved
6:0
Function
Only write 0 to this bit.
CLK3_PHOFF[6:0] Clock 3 Initial Phase Offset.
CLK3_PHOFF[6:0] is an unsigned integer with one LSB equivalent to a time delay of
Tvco/4, where Tvco is the period of the VCO/PLL associated with this output.
58
Rev. 0.6
AN619
Register 169. CLK4 Initial Phase Offset
Bit
D7
D6
D5
D4
D2
D1
D0
R/W
R/W
R/W
CLK4_PHOFF[6:0]
Name
Type
D3
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
Reserved
6:0
Function
Only write 0 to this bit.
CLK4_PHOFF[6:0] Clock 4 Initial Phase Offset.
CLK4_PHOFF[6:0] is an unsigned integer with one LSB equivalent to a time delay of
Tvco/4, where Tvco is the period of the VCO/PLL associated with this output.
Register 170. CLK5 Initial Phase Offset
Bit
D7
D6
D5
D4
D2
D1
D0
R/W
R/W
R/W
CLK5_PHOFF[6:0]
Name
Type
D3
R/W
R/W
R/W
R/W
R/W
Reset value = 0000 0000
Bit
Name
7
Reserved
6:0
Function
Only write 0 to this bit.
CLK5_PHOFF[6:0] Clock 5 Initial Phase Offset.
CLK5_PHOFF[6:0] is an unsigned integer with one LSB equivalent to a time delay of
Tvco/4, where Tvco is the period of the VCO/PLL associated with this output.
Rev. 0.6
59
AN619
Register 177. PLL Reset
Bit
D7
Name
PLLB_RST
Type
R/W
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
PLLA_RST
R/W
R/W
Reset value = 0000 0000
Bit
7
Name
Function
PLLB_RST PLLB_Reset.
Writing a 1 to this bit will reset PLLB. This is a self clearing bit.
6
5
Reserved
Leave as default.
PLLA_RST PLLA_Reset.
Writing a 1 to this bit will reset PLLA. This is a self clearing bit.
4:0
Reserved
Leave as default.
Register 183. Crystal Internal Load Capacitance
Bit
Name
Type
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
XTAL_CL[1:0]
R/W
R/W
Reset value = 11xx xxxx
Bit
7:6
Name
Function
XTAL_CL[1:0] Crystal Load Capacitance Selection.
These 2 bits determine the internal load capacitance value for the crystal. See the Crystal
Inputs section in the Si5351 data sheet.
00: Reserved. Do not select this option.
01: Internal CL = 6 pF.
10: Internal CL = 8 pF.
11: Internal CL = 10 pF (default).
5:0
60
Reserved
Bits 5:0 should be written to 010010b.
Rev. 0.6
AN619
Register 187. Fanout Enable
Bit
Name
Type
D7
D6
CLKIN_FAXO_FANOUT_EN NOUT_EN
R/W
R/W
D5
D4
Reserved
MS_FANOUT_EN
R/W
R/W
D3
D2
D1
D0
R/W
R/W
Reserved
R/W
R/W
Reset value = xxxx xxxx
Bit
Name
Function
7
CLKIN_FANOUT_EN
Enable fanout of CLKIN to clock output multiplexers. Set this bit to 1b.
6
XO_FANOUT_EN
Enable fanout of XO to clock output multiplexers. Set this bit to 1b.
5
Reserved
Reserved.
4
MS_FANOUT_EN
Enable fanout of Multisynth0 and Multisynth4 to all output multiplexers. Set this bit to 1b.
Rev. 0.6
61
AN619
DOCUMENT CHANGE LIST
Revision 0.1 to Revision 0.2

Corrected Typos
Feedback
fractional divide value can be up to 90 (not
900).
Corrected miscellaneous typographical errors.

Added note to “3.2. Feedback Multisynth Divider
Equations” to set MSNB a + b/c divide ratio such that
c = 106 when using VCXO equations in this
document.
 Added Figure 2.
Revision 0.2 to Revision 0.3

Updated first bullet in “Section 5. Configuring Spread
Spectrum Register Parameters.”
 Updated “Section 8.1 Register Map Summary.”
 Updated Register 183.
Revision 0.3 to Revision 0.4

Corrected typographic error in maximum spread
spectrum percentage for center spread on page 8.
 Added rounding operator for up spread depth
calculation on page 9.
 Corrected register description errata on pages 11,13,
31, and 32.
Revision 0.4 to Revision 0.5

Updated “8.1. Register Map Summary”.
Updated “6. Configuring Initial Phase Offset Register
Parameters”.
 Corrected Register 16 description.

Revision 0.5 to Revision 0.6


62
Updated “8.1. Register Map Summary”.
Corrected Register 161 description.
Rev. 0.6
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
Quality
Support and Community
www.silabs.com/CBPro
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com