AA™250/425 Thermal Entrance Doors - Architectural Detail Manual

Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM250/425 Thermal Entrances
EC 97911-065
FEATURES
Features
• AATM250 narrow stile has 2-1/2" (62.5) vertical stiles, 2-1/2" (62.5) top rail, and 3-7/8" (98.4)
bottom rail
• AATM425 wide stile has 4-1/4" (108) vertical stiles, 4-1/4" (108) top rail, and 6-1/2" (165.1)
bottom rail
• Door is 2-1/4" (57.2) deep
• Door has 1/8" (3.2) typical wall thickness
• Dual welded corner construction
• Polyamide thermal break
• Single acting
• 1" (25.4) insulated glass infill
• Offset pivots, butt hinges or continuous geared hinge
• MS locks or exit device hardware
• Surface mounted or concealed closers
• Architects Classic push/pulls
• Meeting stile astragal has dual pile weathering with polymeric fin
• Polymeric bulb weatherstripping and pile weathering with polymeric fin in door frame
• PermanodicTM anodized finishes in seven choices
• Painted finishes in standard and custom choices
Optional Features
• Variety of top, bottom, and cross rails
• Two color finish capability
Product Applications
• AATM250 - engineered for thermal efficiency in moderate traffic applications such as offices,
stores, and apartment buildings
• AATM425 - engineered for thermal efficiency and added strength for schools, institutions and
other increased traffic applications
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
AUGUST, 2015
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADMA050
1
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM250/425 Thermal Entrances
AUGUST, 2015
BLANK PAGE
EC 97911-065
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
AATM250/425 Thermal Entrances
EC 97911-065
INDEX
3
PICTORIAL VIEW................................................................................ 5
DOOR TYPES/SECTION DIMENSIONS.............................................. 6
AATM250 THERMAL ENTRANCE CONSTRUCTION DETAILS.......... 7
TRIFABTM VG 451T CENTER DOOR FRAMES................................ 8-9
ENTRANCE OFFERING............................................................... 10-11
PUSH PULL HARDWARE................................................................. 12
EXIT DEVICES................................................................................... 13
OPTIONS AND ACCESSORIES....................................................... 14
THERMAL CHARTS..................................................................... 15-27
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE,
WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE
SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS,
AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses
(
) are millimeters unless otherwise noted.
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AUGUST, 2015
The following metric (SI ) units are found in these details:
m –meter
cm – centimeter
mm –millimeter
s –second
Pa –pascal
MPa –megapascal
Kawneer reserves the right to change configurations without prior notice when deemed necessary for product
improvement.
kawneer.com
ADMA050
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM250/425 Thermal Entrances
AUGUST, 2015
BLANK PAGE
EC 97911-065
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
AATM250/425 Thermal Entrances
EC 97911-065
PICTORIAL VIEW
#1 MECHANICAL FASTENING is accomplished
by attaching a 5/16" (7.9) thick extruded aluminum
channel clip to the vertical stile with 1/4"-20 heat
strengthened bolts and 3/16" thick steel nut plates
for a high strength welding base for attachment
horizontal member.
#2 SIGMA* DEEP PENETRATION PLUG WELDS
are made top and bottom after the horizontal
is properly positioned over the channel clip to
help provide the strongest door corner joint
currently available.
DUAL MOMENT WELDED CORNER CONSTRUCTION
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AUGUST, 2015
* An arc welding process known as Shielded Inert Gas Metal Arc (SIGMA)
or also known as Metal Inert Gas (MIG).
kawneer.com
ADMA050
#3 SIGMA* FILLET WELDS along both top and
bottom webs of the rail extrusion complete the
Dual Welded corner construction.
5
2-1/4"
(57.2)
TYPICAL
3-7/8"
(98.4)
6-1/2"
(165.1)
2-1/2"
(63.5)
2-1/2"
(63.5)
LOCK STILE
3
3
9/16"
(14.3)
TYPICAL
4
CL
OF CYL.
2
BOTTOM
OF DOOR
1
ADMA050
PANIC LOCK
CYLINDER
3
4
2
1690 = 40-5/8" (1031.9)
BOTTOM
OF DOOR
4
3
4
2-1/2"
(63.5)
4-1/4"
(108)
4-1/4"
(108)
PIVOT STILE
LOCK STILE
PIVOT STILE
C
L OF CRASH BAR FOR
FALCON
C
L OF CRASH BAR FOR
ADAMS RITE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1790 = 41-5/16" (1049.3)
C
L
C
L OF CRASH BAR FOR KAWNEER
STANDARD EXIT DEVICE
STANDARD
EXIT DEVICE
8600 = 41-11/16" (1058.9)
TOP
ATTACHMENT
8400 = 40-13/16" (1036.6)
TOP
ATTACHMENT
1
1686 = 40" (1016)
STANDARD
LOCATIONS
1786 = 40" (1016)
1
41-9/16"
(1042.0)
44-5/16"
(1125.5)
STANDARD
LOCATIONS
4-1/4"
(108)
40-13/16"
(1036.6)
AATM250/425 Thermal Entrances
AUGUST, 2015
DOOR TYPES/SECTION DIMENSIONS
EC 97911-065
2
2
kawneer.com
© Kawneer Company, Inc., 2015
9/16"
(14.3)
250 MEDIUM STILE
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
TYPICAL
44-5/16"
(1125.5)
6
SCALE 3" = 1' 0"
425 WIDE STILE
1
2-1/4"
(57.2)
TYPICAL
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
AATM250 THERMAL ENTRANCE CONSTRUCTION DETAILS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
SCALE 3" = 1'-0"
7
AATM250 THERMAL ENTRANCE DOORS
SINGLE ACTING
TM
TRIFAB VG 451T CENTER DOOR FRAMES SHOWN
NOTE:
1.MEDIEM STILE AATM250 THERMAL ENTRANCES ARE DETAILED, WIDE STILE AATM425 THERMAL ENTRANCES ALSO MAY BE USED.
2.TRIFABTM VG 451T CENTER, 2" X 4-1/2" (50.8 X 114.3) FRAMING IS DETAILED WITH THE DOORS FOR REFERENCE. OTHER KAWNEER
FRAMING SERIES OR CURTAIN WALL SYSTEMS MAY BE USED. REFER TO THE CATALOG INDEX FOR THE APPROPRIATE DETAIL
SECTION.
5
5
4
6
1
1A
2
6
1
1A
7
4
6
3
3A
1
1A
7
6
2
1
1A
7
3
7
5
TRANSOM HEAD
2
PAIR OF SINGLE ACTING DOORS
6
DOOR HEADER/
TRANSOM BAR
1A
3
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1
7*
BOTTOM RAIL
4
TRANSOM
INSERT
kawneer.com
ADMA050
*NOTE: Some building codes limit threshold height to 1/2" (12.7) max.
(17.5)
SINGLE ACTING DOOR
WITHOUT TRANSOM
ADMA050
3/8"
AUGUST, 2015
TRIFAB
EC 97911-065
SINGLE ACTING DOOR
WITH TRANSOM
kawneer.com
© Kawneer Company, Inc., 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM250/425 Thermal Entrances
VG 451T CENTER DOOR FRAMES
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
(9.5)
(17.5)
(28.6)
(3.2)
11/16"
1-1/8"
2"
(50.8)
2"
(50.8)
1/8"
DOOR OPENING
TM
FRAME DIMENSION
MASONRY OPENING
(3.2)
11/16"
2"
(50.8)
1/8"
DOOR OPENING
FRAME DIMENSION
MASONRY OPENING
8
SCALE 3" = 1'-0"
TRIFABTM VG 451T CENTER DOOR FRAMES
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
TRIFABTM VG 451T CENTER DOOR FRAMES
9
1/4"
(6.4)
3/32"
3/32"
(2.4)
2"
DOOR OPENING
(50.8)
(2.4)
2"
(50.8)
FRAME DIMENSION
MASONRY OPENING
SINGLE ACTING DOOR
11/32"
(8.9)
2"
DOOR OPENING
(50.8)
FRAME DIMENSION
MASONRY OPENING
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
SCALE 3" = 1'-0"
CONTINUOUS HINGE JAMB
STANDARD SIZES (TRIFABTM VG 451T CENTER FRAMES)
WITHOUT TRANSOM
Door Opening Dimension
Overall Frame Dimension
3' 0" x 7' 0" ( 914 x 2134)
3' 3-1/2" x 7' 1-3/4" (1003 x 2178)
3' 6" x 7' 0" (1067 x 2134)
3' 9-1/2" x 7' 1-3/4" (1156 x 2178)
6' 0" x 7' 0" (1829 x 2134)
6' 3-1/2" x 7' 1-3/4" (1918 x 2178)
Masonry Opening Dimension
3' 4" x 7' 2" (1016 x 2185)
3' 10" x 7' 2" (1168 x 2185)
6' 4" x 7' 2" (1930 x 2185)
WITH TRANSOM
Door Opening Dimension
Unchanged from above.
Masonry Opening Dimension
Add 3' 1-3/4" (959) to above heights.
kawneer.com
Overall Frame Dimension
Add 3' 1-3/4" (959) to above heights.
ADMA050
AATM250/425 Thermal Entrances
AUGUST, 2015
ENTRANCE OFFERINGS
EC 97911-065
OPTIONAL
Doors
Narrow stile 250 doors prepared for attachment hardware.
Wide stile 425.
Door Sizes Std.
Standard sizes shown on page 9.
Any size up to 3'-6" x 8'-0" (1067 x 2438).
Glass Stops
Square glass stops for 1" (25.4) infill.
Door Frames
TrifabTM VG 451T Center - 2" x 4-1/2" (50.8 x 114.3) for double
glazing.
Other Kawneer framing system suitable for door frames may be
selected, but manufactured per order.
Push-Pulls
Single Acting:
Single Acting:
Architects Classic Hardware "CO-9" Pull and
"CP-II" Push Bar.
Architects Classic Hardware "CO-9" Pull and
"CP" Push Bar.
Architects Classic Hardware
"CO-12" and "CP-II" push bar.
Architects Classic Hardware
"CO-12" and "CP" push bar.
Architects Classic Hardware
"CO-9"/"CO-9" Pulls.
Architects Classic Hardware
"CO-12"/"CO-12" Pulls.
Door Closers
Single Acting:
Norton 1601 adjustable or 1601 BF
adjustable surface closer with back-check
and with or without adjustable hold-open.
Single Acting:
LCN 1260 adjustable surface closer.
LCN 4040 surface closer with or without
adjustable hold-open.
Standard COC with single scting offset arm.
Norton 8100 surface closer with a 50%
spring power adjustment (for opening forces
of less than 8 pounds). Closer is available
with standard back-checks and with or
without the hold-open feature.
Falcon SC 60 Surface closer.
Hinging
Single Acting:
Kawneer top and bottom offset pivots
(or) Kawneer top and bottom 4 1/2" x 4"
(114.3 x 101.6) ball bearing butt hinge with
non-removable pin (NRP) (or) Kawneer
continuous gear hinge.
Intermediate
Pivots/Butts
Single Acting:
Kawneer intermediate offset pivot (or)
Kawneer 4-1/2" x 4" (114.3 x 101.6) ball
bearing butt hinge with non-removable pin
(NRP).
Single Acting:
Power
Transfers
Single Acting:
Kawneer EL intermediate offset pivot (or)
Kawneer EL 4 1/2" x 4" (114.3 x 101.6) ball
bearing butt hinge with wire transfer (or)
EPT (Electric Power Transfer).
SP-1000X Power Supply: For use with EL exit devices.
Power Supply
PS1, PS5-4, and PS5-6 Power Supplies: For use with
Kawneer 1686 EL and 1786 EL exit devices only.
SP-1000X Power Supply.
Locks Active Leaf
Adams-Rite MS 1850A deadlock with two 1-5/32" (29.4)
diameter 5 pin cylinders.
Adams-Rite #4510 Latch Lock.
Adams-Rite #1850A-500 Short Throw Deadlock.
Adams-Rite #1850A-505 Hookbolt Lock.
Adams-Rite #4015 Two-point Lock.
Adams-Rite #4015 & 4016 three-point lock.
Adams-Rite #7130 Electric Strike.
Kawneer Cylinder Guard.
Kawneer Thumbturn (in lieu of cylinder).
ADMA050
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Rixson M-19 or IVES #7215-INT
intermediate offset pivot.
kawneer.com
© Kawneer Company, Inc., 2015
STANDARD
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
10
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
ENTRANCE OFFERINGS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
STANDARD
11
OPTIONAL
Locks Inactive Leaf
One pair of Kawneer flush bolts in the inactive leaf of a pair of
doors.
Thresholds
A 1/2" x 4-1/2" (12.7 x 114.3) aluminum mill finish threshold.
Weathering
Single Acting:
Exit Device
Kawneer 1686 Concealed Rod Exit Device with or without a
mortised type cylinder.
Kawneer 1686 CD concealed rod exit device available with
cylinder dogging.
Kawneer 1786 Rim Exit Device is a rim type exit device with
or without a rim type cylinder.
Kawneer 1786 CD rim exit device available with cylinder
dogging.
Weathering system in the door and frame
consisting of a dense, bulb polymeric
material, which remains resilient and retains
its weathering ability under temperature
extremes. Complete with an optional EPDM
blade gasket sweep strip applied to both the
interior and exterior of the bottom rail with
concealed fasteners.
Kawneer 1686 EL Concealed Rod Exit Device electric
modification is available.
Kawneer 1786 EL Rim Exit Device electric modification is
available.
Adams-Rite 8600 concealed rod exit device.
Adams-Rite 8400 rim exit device.
Falcon 1690 Concealed Rod Exit Device with or without rim
type cylinder.
Falcon EL 1690 concealed rod exit device with or without a
rim type cylinder. The device is designed for electrified access
control and is compatible with most key pad and card reader
systems.
Falcon EL 1790 rim type exit device with or without a rim type
cylinder. The device is designed for electrified access control
and is compatible with most key pad and card reader systems.
Falcon 1990 is a concealed rod exit device with or without a
rim type cylinder.
Falcon 2090 is a rim type exit device with or without a rim type
cylinder.
Von Duprin 33 concealed rod exit device with or without night
latch assembly.
Von Duprin 99 concealed rod exit device with or without night
latch assembly.
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Falcon 1790 Rim Exit Device rim type exit device with or
without a rim type cylinder.
Exit Device Pulls:
Architects Classic style "CO-9" Pull.
Optional Exit Device Pulls:
Architects Classic style "CO-12" Pull.
Reference Hardware section for additional information
kawneer.com
ADMA050
AUGUST, 2015
PUSH-PULL HARDWARE
EC 97911-065
SINGLE ACTING DOORS USE A PULL HANDLE AND PUSH BAR.
CP-II / CP-II
CO-9 / CP
CO-12 / CP
"CO-9"
PULL
CO-9 / CP-II
CO-12 / CP-II
"CO-12"
PULL
"CP-II" PUSH BAR
ADMA050
CP / CP
CO-9 / CO-9
CO-12 / CO-12
"CP" PUSH BAR
kawneer.com
© Kawneer Company, Inc., 2015
AATM250/425 Thermal Entrances
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
ARCHITECTS CLASSIC (PUSH PULL SETS)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
12
Refer to HARDWARE SECTION for
complete hardware information.
ARCHITECTS CLASSIC (COMPONENTS)
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
EXIT DEVICES
CONCEALED ROD EXIT DEVICE
Kawneer 1686
Kawneer 1686 CD
Kawneer 1686 EL
RIM LATCH EXIT DEVICE
Kawneer 1786
Kawneer 1786 CD
Kawneer 1786 EL
CONCEALED ROD EXIT DEVICE
Falcon 1690
Falcon EL 1690
RIM LATCH EXIT DEVICE
Falcon 1790
Falcon EL 1790
MORTISE EXIT DEVICE
Adams-Rite 8400
CONCEALED EXIT DEVICE
Adams-Rite 8600
CONCEALED EXIT DEVICE
Von Duprin 3347A
CONCEALED EXIT DEVICE
Von Duprin 9947
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EXIT DEVICES and EXIT DEVICE PULLS
"CO-9"
PULL
kawneer.com
"CO-12"
PULL
LEVER HANDLE
Kawneer 1686
Kawneer 1786
CONCEALED ROD EXIT DEVICE
Falcon 1990
ADMA050
RIM LATCH EXIT DEVICE
Falcon 2090
13
069154
10"
APPLIED DOOR STOP
ADMA050
069177
10" BOTTOM RAIL
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
8-1/4"
8-1/4" CROSSRAIL
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
(209.6)
AATM250/425 Thermal Entrances
AUGUST, 2015
OPTIONS AND ACCESSORIES
EC 97911-065
kawneer.com
© Kawneer Company, Inc., 2015
1"
(25.4)
1-3/8" CROSSRAIL
(254.0)
(62.7)
1/2"
2-15/32"
(12.7)
(17.5)
APPLIED DOOR STOP
11/16"
1/2"
(62.7)
(12.7)
2-15/32"
(34.9)
1-3/8"
14
SCALE 3" = 1'-0"
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL CHARTS
Generic Project Specific U-factor Example Calculation
(Percent of Glass will vary on specific products depending on sitelines)
30.125"
(765.2)
(DLO)
75.75"
(1924.1)
(F.H.)
7'-2"
(2184.4)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
(DLO)
3'-4"
(1016.0)
(F.W.)
Example Glass U-Factor = 0.28 Btu/hr • ft2 • °F
Total Daylight Opening
= 30.125" x 75.75" = 15.85 ft2
Total Projected Area
= 3'-4" x 7'-2" = 23.9 ft2
Percent of Glass
= (Total Daylight Opening ÷ Total Projected Area)100
= (15.85 ÷ 23.9)100 = 66%
System U-factor vs Percent of Glass Area
0.90
0.80
0.75
N
© Kawneer Company, Inc., 2015
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
0.65
0.60
0.55
0.50
0.49
0.45
0.40
0.35
0.30
0.25
0.20
80
70
75
Percent of Glass Area
65
66%
85
Based on 66% glass and center of glass (COG) U-factor of 0.28
System U-factor is equal to 0.49 Btu/hr • ft2 • °F
kawneer.com
ADMA050
60
Btu
hr • ft2 • °F
System U-factor
COG
U-factor
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.70
E IGN
PL S
M E
A D
EX OR
F
T
O
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.85
15
AATM250/425 Thermal Entrances
AUGUST, 2015
THERMAL CHARTS
EC 97911-065
AATM250 (SINGLE DOOR)
COG
U-factor
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.80)
0.12 (0.68)
0.10 (0.57)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
Percent of Glass = Vision Area/Total Area
(Total Daylight Opening / Projected Area)
Notes for System U-Factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values (winter conditions) and are obtained
from your glass supplier.
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System U-factor vs Percent of Glass Area
System U-factor (BTU/hr·ft2·oF)
16
System VT
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL CHARTS
Vision Area / Total Area (%)
kawneer.com
ADMA050
17
AATM250 (SINGLE DOOR)
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
AATM250/425 Thermal Entrances
AUGUST, 2015
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
EC 97911-065
Overall U-Factor 4
0.48
0.57
0.46
0.57
0.44
0.55
0.42
0.54
0.40
0.53
0.38
0.52
0.36
0.51
0.34
0.50
0.32
0.49
0.30
0.48
0.28
0.47
0.26
0.46
0.24
0.46
0.22
0.44
0.20
0.43
0.18
0.42
0.16
0.41
0.14
0.40
0.12
0.39
0.10
0.38
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 960mm wide by
2090mm high (37-3/4" by 82-3/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.45
0.75
0.43
0.70
0.42
0.70
0.40
0.65
0.39
0.65
0.37
0.60
0.36
0.60
0.34
0.55
0.34
0.55
0.31
0.50
0.31
0.50
0.29
0.45
0.28
0.45
0.26
0.40
0.25
0.40
0.23
0.35
0.22
0.35
0.20
0.30
0.19
0.30
0.17
0.25
0.16
0.25
0.14
0.20
0.13
0.20
0.11
0.15
0.11
0.15
0.09
0.10
0.08
0.10
0.06
0.05
0.05
0.05
0.03
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM250 (SINGLE DOOR)
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
18
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL CHARTS
AATM250 (PAIR OF DOORS)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System U-factor vs Percent of Glass Area
System U-factor (BTU/hr·ft2·oF)
COG
U-factor
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.80)
0.12 (0.68)
0.10 (0.57)
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.22 (1.25)
Percent of Glass = Vision Area/Total Area
(Total Daylight Opening / Projected Area)
Notes for System U-Factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values (winter conditions) and are obtained
from your glass supplier.
kawneer.com
ADMA050
19
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
ADMA050
COG
SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
AATM250/425 Thermal Entrances
AUGUST, 2015
THERMAL CHARTS
EC 97911-065
Vision Area / Total Area (%)
kawneer.com
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
20
AATM250 (PAIR OF DOORS)
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
Vision Area / Total Area (%)
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
AATM250 (PAIR OF DOORS)
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.56
0.46
0.55
0.44
0.54
0.42
0.53
0.40
0.52
0.38
0.51
0.36
0.50
0.34
0.49
0.32
0.48
0.30
0.46
0.28
0.45
0.26
0.44
0.24
0.43
0.22
0.42
0.20
0.41
0.18
0.39
0.16
0.38
0.14
0.37
0.12
0.36
0.10
0.35
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
kawneer.com
21
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1920mm wide by
2090mm high (75-1/2" by 82-3/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.48
0.75
0.46
0.70
0.45
0.70
0.43
0.65
0.42
0.65
0.40
0.60
0.39
0.60
0.37
0.55
0.36
0.55
0.34
0.50
0.32
0.50
0.31
0.45
0.29
0.45
0.28
0.40
0.26
0.40
0.25
0.35
0.23
0.35
0.21
0.30
0.20
0.30
0.18
0.25
0.17
0.25
0.15
0.20
0.14
0.20
0.12
0.15
0.11
0.15
0.09
0.10
0.08
0.10
0.06
0.05
0.05
0.05
0.03
ADMA050
AATM250/425 Thermal Entrances
AUGUST, 2015
THERMAL CHARTS
EC 97911-065
AATM425 (SINGLE DOOR)
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.80)
0.12 (0.68)
0.10 (0.57)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
COG
U-factor
Percent of Glass = Vision Area/Total Area
(Total Daylight Opening / Projected Area)
Notes for System U-Factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values (winter conditions) and are obtained
from your glass supplier.
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System U-factor vs Percent of Glass Area
System U-factor (BTU/hr·ft2·oF)
22
System VT
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL CHARTS
AATM425 (SINGLE DOOR)
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
Vision Area / Total Area (%)
kawneer.com
ADMA050
23
AATM250/425 Thermal Entrances
AUGUST, 2015
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
EC 97911-065
Overall U-Factor 4
0.48
0.58
0.46
0.58
0.44
0.57
0.42
0.56
0.40
0.55
0.38
0.54
0.36
0.53
0.34
0.52
0.32
0.51
0.30
0.51
0.28
0.50
0.26
0.49
0.24
0.48
0.22
0.47
0.20
0.46
0.18
0.44
0.16
0.43
0.14
0.43
0.12
0.42
0.10
0.41
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 960mm wide by
2090mm high (37-3/4" by 82-3/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.39
0.75
0.36
0.70
0.36
0.70
0.34
0.65
0.34
0.65
0.32
0.60
0.32
0.60
0.29
0.55
0.29
0.55
0.27
0.50
0.27
0.50
0.24
0.45
0.24
0.45
0.22
0.40
0.22
0.40
0.19
0.35
0.19
0.35
0.17
0.30
0.17
0.30
0.15
0.25
0.15
0.25
0.12
0.20
0.12
0.20
0.10
0.15
0.10
0.15
0.07
0.10
0.07
0.10
0.05
0.05
0.05
0.05
0.02
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM425 (SINGLE DOOR)
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
24
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL CHARTS
AATM425 (PAIR OF DOORS)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System U-factor vs Percent of Glass Area
COG
U-factor
System U-factor (BTU/hr·ft2·oF)
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
0.18 (1.02)
0.12 (0.68)
0.10 (0.57)
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.16 (0.91)
0.14 (0.80)
Percent of Glass = Vision Area/Total Area
(Total Daylight Opening / Projected Area)
Notes for System U-Factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values (winter conditions) and are obtained
from your glass supplier.
kawneer.com
ADMA050
25
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
ADMA050
COG
SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
AATM250/425 Thermal Entrances
AUGUST, 2015
THERMAL CHARTS
EC 97911-065
Vision Area / Total Area (%)
kawneer.com
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
26
AATM425 (PAIR OF DOORS)
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
Vision Area / Total Area (%)
AUGUST, 2015
AATM250/425 Thermal Entrances
EC 97911-065
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
AATM425 (PAIR OF DOORS)
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.57
0.46
0.57
0.44
0.56
0.42
0.55
0.40
0.54
0.38
0.53
0.36
0.52
0.34
0.51
0.32
0.50
0.30
0.49
0.28
0.48
0.26
0.47
0.24
0.46
0.22
0.45
0.20
0.44
0.18
0.43
0.16
0.42
0.14
0.41
0.12
0.40
0.10
0.39
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
kawneer.com
27
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1920mm wide by
2090mm high (75-1/2" by 82-3/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.42
0.75
0.39
0.70
0.39
0.70
0.37
0.65
0.36
0.65
0.34
0.60
0.34
0.60
0.32
0.55
0.31
0.55
0.29
0.50
0.28
0.50
0.26
0.45
0.26
0.45
0.24
0.40
0.23
0.40
0.21
0.35
0.21
0.35
0.18
0.30
0.18
0.30
0.16
0.25
0.15
0.25
0.13
0.20
0.13
0.20
0.11
0.15
0.10
0.15
0.08
0.10
0.07
0.10
0.05
0.05
0.05
0.05
0.03
ADMA050
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AATM250/425 Thermal Entrances
AUGUST, 2015
BLANK PAGE
EC 97911-065
ADMA050
kawneer.com
© Kawneer Company, Inc., 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
28
Similar pages