a p p l i c at i o n N o t e Gas Chromatography/ Mass Spectrometry Author Meng Yuan PerkinElmer, Inc. Shelton, CT 06484 USA Analysis of Butylated Hydroxytoluene in Food with Headspace Trap-GC/MS Introduction Butylated hydroxytoluene (BHT, 2,6-di-tert-butyl-4-methylphenol) is a common food additive. BHT is found in many types of food including butter, meats, cereals, chewing gum, baked goods, snack foods, dehydrated potatoes and beverages. It is used to preserve food odor, color and flavor. BHT is oxidized preferentially in fats or oils, protecting the foods from spoilage. Concern exists that long-term human consumption of BHT may have potential health risks. It has undergone the additive application and review process required by the U.S. Food and Drug Administration (FDA); the committee concluded that no evidence in the available information on BHT demonstrates a hazard to the public when it is used at levels that are now current and in the manner now practiced. However, uncertainties exist requiring that additional studies should be conducted.1 The chemical properties which make BHT an excellent preservative may also be implicated in health effects. The oxidative characteristics and metabolites of BHT may contribute to carcinogenicity. Some people may have difficulty metabolizing BHT, resulting in health and behavioral changes. This application note will demonstrate a fast and easy analytical technique to determine the amount of BHT in foods. Headspace (HS) sample introduction is used because it provides a means to analyze food without any sample preparation. Headspace eliminates the need for solvents and other samplepreparation steps to reduce cost and complexity of extraction. In this application note, an adsorbent trap is used to concentrate the headspace sample and increase sensitivity, allowing for low-level detection or small sample sizes. The analysis is carried out with gas chromatography mass spectrometry (GC/MS) – this will allow us to resolve the BHT from other volatile compounds in the food matrices and provide positive identification of the BHT with mass spectral data. Calibration of the system and analysis of food samples will be demonstrated. Experimental The instrumental platform for this application is the TurboMatrix™ HS Trap coupled to a Clarus® 680 GC/MS, both platforms from PerkinElmer. The transfer line of the HS was directly connected to the Elite™-17ms column with a universal butt connector. The samples are heated in a sealed vial at 80 ˚C for 30 minutes to drive the BHT from the food into the headspace. Using automated headspace technology, the gas is extracted from the vial, concentrated on an adsorbent trap (PerkinElmer® Air Toxics), and injected into the GC/MS system. Table 1 shows the detailed instrumental setup parameters for the HS Trap-GC/MS system. Table 1. Instrument Parameters. Sample Introduction PerkinElmer TurboMatrix HS-40 Trap Needle Temperature 90 ˚C Transfer Line Temperature 110 ˚C Oven Temperature 80 ˚C Trap Low Temperature 40 ˚C Trap High Temperature 280 ˚C Dry Purge (Helium) 5 min Trap Hold Time 6 min Desorb Time 0.5 min Thermostatting Time Gas Chromatograph PerkinElmer Clarus 680 GC Headspace Connector Universal Connector Inlet Temperature 150 ˚C Oven Program Initial Temp 50 ˚C Hold Time 1 1 min Ramp 1 25 ˚C/min to 280 ˚C Hold Time 2 1.8 min Vacuum Compensation On Headspace Control On 30 min Column Elite-17ms 30 m x 0.25 mm x 0.25 μm Pressurization Time 1 min Carrier Gas Helium Decay Time 2 min Mass Spectrometer PerkinElmer Clarus 600 MS Column Pressure 17 psi Mass Range 45-300 u Vial Pressure 35 psi Solvent Delay Time 0.1 min Desorb Pressure 10 psi Scan Time 0.20 sec Universal Capillary Column Connector Part No. N9302149 InterScan Delay Time 0.02 sec Transfer Line Fused Silica 2 m x 320 μm Transfer Line Temperature 240 °C Source Temperature 200 °C Multiplier 500 V Calibration-Standards Preparation A 10 ng/μL standard stock solution was prepared by diluting 0.1 mL of a 1000 μg/mL BHT standard to 10 mL with methanol. 1 ng/μL, 2 ng/μL and 5 ng/μL standard working solutions were prepared by diluting 0.1 mL, 0.2 mL and 0.5 mL of a 10 ng/μL BHT standard to 1 mL with methanol. 20 ng/μL, 50 ng/μL and 100 ng/μL standard working solution was prepared by diluting 0.02 mL, 0.05 mL and 0.1 mL of a 1000 μg/mL BHT standard to 1 mL with methanol. 2 The working curve was prepared by injecting 1 μL of each working standard solution into headspace vials. Working calibration standards at 1, 2, 5, 10, 20, 50, and 100 ng were prepared fresh each day. One gram of each food sample purchased at local Shanghai markets were placed into the headspace vials. All headspace vials were sealed immediately and transferred to the headspace-trap vial tray. Figure 1. Example chromatogram of a 100 ng standard injection of BHT. Results and Discussion The instrument calibration included seven calibration levels in the working curve; the response of this calibration curve was linear (Table 2). Additionally, the method is precise throughout the calibration range, as demonstrated by the relative standard deviation of 3.2% at the calibration limit (1 ng, n=5) and 1.9% at 10 ng (n=5). Figure 1 is an extracted ion chromatogram, of m/z 205, from the analysis of a 100 ng BHT standard. Figure 2 demonstrates the spectral data of BHT which matches exactly the fragmentation of BHT in the NIST® spectral library. Following the calibration of the system, five food samples were analyzed: a cracker, powdered coffee creamer, instant noodles, sausage, and tea leaves. The BHT concentrations are quantified (Table 3). BHT concentration in the food samples analyzed here was below the quantitation limit of 1 ng/g. It can be seen in Figure 3 (Page 4) that the BHT peak is easily identified in the sample analysis. Each sample was analyzed in triplicate – the area reproducibility achieved (Table 3) demonstrates that the method remains very precise, even below the quantitation limit. Figure 2. Background subtracted spectra from the analysis of a BHT standard. Table 2. Calibration Table for BHT. Name Retention Time (min) Quantifier Ion Qualifier Ion 1 Qualifier Ion 2 %RSD (n=5 at 1 ng) %RSD (n=5 at 10 ng) r2 BHT 7.60 205 220 57 3.2 1.9 0.9980 Table 3. %RSD of BHT in Food Samples. Sample BHT (ng/g) in 1 g of Sample BHT (ng/g) in 1 g of Duplicate BHT (ng/g) in 1 g of Triplicate Values Mean (ng/g) %RSD Crackers 0.65 0.55 0.54 0.58 10.5 Coffee Creamer 0.66 0.73 0.69 0.69 5.1 Instant Noodles 0.67 0.67 0.70 0.68 2.5 Sausage 0.67 0.53 0.56 0.59 12.6 Tea Leaves 0.62 0.54 0.53 0.56 8.8 3 Figure 3. Resultant chromatogram from the analysis of instant noodles for BHT. Conclusion References BHT is a common food additive used to prevent spoilage. Analysis of BHT is needed for both food quality and safety reasons. Food is often a complicated sample matrix which is time consuming to prepare and analyze. This method uses headspace technology to virtually eliminate sample preparation and reduce the cost and labor of the analysis. In addition to eliminating sample preparation, the method is both sensitive and precise as demonstrated by the analysis of standard reference materials and a variety of food samples. The throughput of the system is further improved by the Clarus 680 GC/MS with a fast-cooling GC oven, further improving throughput and productivity. The MS data provides positive confirmation of BHT in sample matrices. 1.Database of Select Committee on GRAS Substances (SCOGS) Reviews-Butylated Hydroxytoluene (BHT), available from http://www.accessdata.fda.gov/scripts/fcn/ fcnDetailNavigation.cfm?rpt=scogsListing&id=41 PerkinElmer, Inc. 940 Winter Street Waltham, MA 02451 USA P: (800) 762-4000 or (+1) 203-925-4602 www.perkinelmer.com For a complete listing of our global offices, visit www.perkinelmer.com/ContactUs Copyright ©2010, PerkinElmer, Inc. All rights reserved. PerkinElmer® is a registered trademark of PerkinElmer, Inc. All other trademarks are the property of their respective owners. 009138_01