AA®4325 Series OptiQ™ Ultra Thermal Window - Architectural Details

JANUARY, 2015
AA™4325 Series Windows
INDEX
FIXED WINDOW................................................................................. 3-6
PROJECT-IN WINDOW.................................................................... 7-10
PROJECT-OUT WINDOW.............................................................. 11-14
INSWING CASEMENT WINDOW.................................................. 15-18
OUTSWING CASEMENT WINDOW.............................................. 19-22
RECEPTORS, SUB SILLS AND ANCHORING.................................. 23
PANNING............................................................................................ 24
THERMAL CHARTS...................................................................... 25-43
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED
ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT
CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR
GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference.
Numbers in parentheses (
) are millimeters unless otherwise noted.
The following metric (SI) units are found in these details:
m –meter
cm – centimeter
mm –millimeter
s –second
Pa –pascal
MPa –megapascal
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-071
1
Kawneer reserves the right to change configurations without prior notice when deemed necessary
for product improvement.
kawneer.com
ADME060
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AA™4325 Series Windows
BLANK PAGE
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
JANUARY, 2015
EC 97911-071
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
FIXED WINDOW
Standard Features
Architectural Grade Window
Tested to US and Canadian Standards
Polyamide Thermal Break
Tubular Profiles
45° Mitered Frame Corners
Staked Corner Joinery
Factory Silicone Glazed
Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
Thermal Break
Exterior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
•
•
•
•
•
•
•
•
Interior
Fixed Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME060
3
AA™4325 Series Windows
EC 97911-071
Architectural Class AW-PG80-FW
TESTING STANDARD
AAMA / WDMA CSA 101 / I.S.2 / A440-05 / A440-08
FRAME DEPTH
3-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.080 Nominal Frame
TYPICAL MAXIMUM SIZE
60" x 99"
TYPICAL MINIMUM SIZE
17" x 17"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" and 1-3/4" (Other infill options available upon request.)
STANDARD HARDWARE
Not Applicable
OPTIONAL HARDWARE
Not Applicable
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Receptor and Sub Sill
Panning
Internal Blinds
Exterior or Interior Muntins
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
FIXED WINDOW
JANUARY, 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
kawneer.com
D.L.O.
W.D.
O.D.
5
JAMB
D.L.O.
D.L.O.
D.L.O.
2
HORIZONTAL
D.L.O.
3-1/4"(83)
6
VERTICAL
D.L.O.
6
VERTICAL
5
JAMB
ADME060
3-1/4"(83)
3 4
D.L.O.
D.L.O.
1
HEAD
3
SILL
4
SILL
2-1/4"(57)
6
W.D.
O.D.
2-1/4"(57)
W.D.
O.D.
2
2-1/4"(57)
2-1/4"(57)
3/8"(10)
3/8"(10)
1
W.D.
3/8"(10)
O.D.
3-1/4"(83)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
5
1/2"(13)
3-1/4"(83)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
JANUARY, 2015
AA™4325 Series Windows
EC 97911-071
3-1/4"(83)
1
HEAD
TYPICAL ELEVATION
2
HORIZONTAL
3
SILL
4
SILL
5
FIXED WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
3-1/4"(83)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AA™4325 Series Windows
BLANK PAGE
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
6
JANUARY, 2015
EC 97911-071
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
PROJECT-IN WINDOW
Standard Features
Architectural Grade Window
Tested to US and Canadian Standards
Polyamide Thermal Break
Tubular Profiles
45° Mitered Vent and Frame Corners
Staked Corner Joinery
Factory Silicone Glazed
Adjustable EURO-Groove Mounted Hardware
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
Exterior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
•
•
•
•
•
•
•
•
Interior
Project-In Window
Thermal Break
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME060
7
AA™4325 Series Windows
EC 97911-071
Architectural Grade AW-PG80-AP
TESTING STANDARD
AAMA / WDMA CSA 101 / I.S.2 / A440-05 / A440-08
FRAME DEPTH
3-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.080 Nominal Frame / .125" Nominal Vent
TYPICAL MAX. VENT SIZE
60" x 36"
TYPICAL MIN. VENT SIZE
24" x 19"
TYPICAL CONFIGURATIONS
INFILL OPTIONS
1" and 1-3/4" (Other infill options available upon request.)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Handles
OPTIONAL HARDWARE
Access Control Locks
Pole and Pole Ring
Limit Stop
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
Receptor and Sub Sill
Panning
Internal Blinds
Exterior or Interior Muntins
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
CLASS and GRADE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PROJECT-IN WINDOW
JANUARY, 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
8
3-1/4"(83)
© Kawneer Company, Inc., 2014
3-3/8"(86)
4
JAMB
kawneer.com
3
SILL
W.D.
D.L.O.
D.L.O.
D.L.O.
D.L.O.
1
HEAD
3-3/8"(86)
W.D.
O.D.
O.D.
3-3/8"(86)
W.D.
4
3-3/8"(86)
3/8"(10)
3/8"(10)
3/8"(10)
1
W.D.
TYPICAL ELEVATION
O.D.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
2 3
1/2"(13)
3-1/4"(83)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
JANUARY, 2015
AA™4325 Series Windows
EC 97911-071
PROJECT-IN WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
3-1/4"(83)
2
SILL
4
JAMB
ADME060
3-1/4"(83)
1
HEAD
2
SILL
O.D.
3
SILL
9
AA™4325 Series Windows
JANUARY, 2015
A standard hinge for ventilators providing
approximately 45° to 60° openings depending on
size. An optional limit stop is available to restrict
hinge travel and limit vent opening.
CAM HANDLE
Cast white bronze cam handles are an alternative
to standard multi-point locking for the operation
and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring
provide manual operation of ventilators located
above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction
with locking hardware for sash pole operation of
ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast
white bronze pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional
cast white bronze Pole Hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast
white bronze access control locks are offered for
managed control of vent operations.
Lock is operated with a manganese bronze
removable handle.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-071
PROJECT-IN WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
PROJECT-OUT WINDOW
Standard Features
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
•
•
•
•
•
•
•
•
Architectural Grade Window
Tested to US and Canadian Standards
Polyamide Thermal Break
Tubular Profiles
45° Mitered Vent and Frame Corners
Staked Corner Joinery
Factory Silicone Glazed
Adjustable EURO-Groove Mounted Hardware
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
Exterior
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Thermal Break
Interior
Project-out Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME060
11
AA™4325 Series Windows
EC 97911-071
CLASS and GRADE
Architectural Grade AW-PG80-AP
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08
FRAME DEPTH
3-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.080 Nominal Frame / .125" Nominal Vent
TYPICAL MAX. VENT SIZE
60" x 36"
TYPICAL MIN. VENT SIZE
24" x 19"
INFILL OPTIONS
1" and 1-3/4" (Other infill options available upon request.)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Handles
OPTIONAL HARDWARE
Access Control Locks
Pole and Pole Ring
Limit Stop
Roto Operator
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
Receptor and Sub Sill
Panning
Internal Blinds
Exterior or Interior Muntins
ADME060
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
TYPICAL CONFIGURATIONS
kawneer.com
© Kawneer Company, Inc., 2014
PROJECT-OUT WINDOW
JANUARY, 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
12
kawneer.com
3-3/8"(86)
O.D.
D.L.O.
D.L.O.
D.L.O.
1
HEAD
2
SILL
3-3/8"(86)
2 3
W.D.
O.D.
O.D.
3-3/8"(86)
W.D.
4
3-3/8"(86)
3/8"(10)
3-1/4"(83)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
3/8"(10)
1
W.D.
O.D.
3/8"(10)
1/2"(13)
3-1/4"(83)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
JANUARY, 2015
AA™4325 Series Windows
EC 97911-071
PROJECT-OUT WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
3-1/4"(83)
3
SILL
4
JAMB
ADME060
3-1/4"(83)
1
HEAD
TYPICAL ELEVATION
2
SILL
W.D.
D.L.O.
4
JAMB
3
SILL
13
AA™4325 Series Windows
JANUARY, 2015
A standard hinge for ventilators providing
approximately 45° to 60° openings depending on
size. An optional limit stop is available to restrict
hinge travel and limit vent opening.
CAM HANDLE
Cast white bronze cam handles are an alternative
to standard multi-point locking for the operation
and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring
provide manual operation of ventilators located
above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction
with locking hardware for sash pole operation of
ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast
white bronze pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional
cast white bronze Pole Hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast
white bronze access control locks are offered for
managed control of vent operations.
Lock is operated with a manganese bronze
removable handle.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-071
PROJECT-OUT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
14
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
INSWING CASEMENT WINDOW
Standard Features
Inswing Casement
Window
HINGED
LEFT
Thermal Break
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
• Architectural Grade Window
• Tested to US and Canadian Standards
• Polyamide Thermal Break
• Tubular Profiles
• 45° Mitered Vent and Frame Corners
• Staked Corner Joinery
• Factory Silicone Glazed
• Adjustable EURO-Groove Mounted Hardware
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
Interior
Exterior
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME060
15
AA™4325 Series Windows
EC 97911-071
CLASS and GRADE
Architectural Grade AW-PG80-C
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08
FRAME DEPTH
3-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.080 Nominal Frame / .125" Nominal Vent
TYPICAL MAX. VENT SIZE
36" x 60"
TYPICAL MIN. VENT SIZE
19" x 24"
INFILL OPTIONS
1" and 1-3/4" (Other infill options available upon request.)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Handles
OPTIONAL HARDWARE
Access Control Locks
Pole and Pole Ring
Limit Stop
Butt Hinges with Friction Adjusters
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
Receptor and Sub Sill
Panning
Internal Blinds
Exterior or Interior Muntins
ADME060
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
TYPICAL CONFIGURATIONS
kawneer.com
© Kawneer Company, Inc., 2014
INSWING CASEMENT WINDOW
JANUARY, 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
16
kawneer.com
W.D.
O.D.
4
JAMB
4
JAMB
D.L.O.
D.L.O.
W.D.
5
JAMB
D.L.O.
3-3/8"(86)
5
JAMB
ADME060
D.L.O.
D.L.O.
1
HEAD
2
SILL
3
SILL
3-3/8"(86)
W.D.
O.D.
2 3
3-3/8"(86)
3/8"(10)
3-1/4"(83)
3-3/8"(86)
W.D.
O.D.
3/8"(10)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
4
W.D.
O.D.
3/8"(10)
1/2"(13)
3-1/4"(83)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
JANUARY, 2015
AA™4325 Series Windows
EC 97911-071
3-1/4"(83)
5
1
HEAD
TYPICAL ELEVATION
2
SILL
3-3/8"(86)
O.D.
3/8"(10)
3
SILL
17
INSWING CASEMENT WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
1
3-1/4"(83)
AA™4325 Series Windows
JANUARY, 2015
A standard hinge for ventilators providing
approximately 45° to 60° openings depending on
size. An optional limit stop is available to restrict
hinge travel and limit vent opening.
CAM HANDLE
Cast white bronze cam handles are an alternative
to standard multi-point locking for the operation
and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring
provide manual operation of ventilators located
above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction
with locking hardware for sash pole operation of
ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast
white bronze pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional
cast white bronze Pole Hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast
white bronze access control locks are offered for
managed control of vent operations.
Lock is operated with a manganese bronze
removable handle.
BUTT HINGE
An optional hinge available in clear or bronze
anodized finishes or painted to match window.
Must be used with Friction Adjusters.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-071
INSWING CASEMENT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
18
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
OUTSWING CASEMENT WINDOW
Standard Features
Architectural Grade Window
Tested to US and Canadian Standards
Polyamide Thermal Break
Tubular Profiles
45° Mitered Vent and Frame Corners
Staked Corner Joinery
Factory Silicone Glazed
Adjustable EURO-Groove Mounted Hardware
• Interior Applied Glazing Bead
• Architectural Anodized Finishes and Applied Coatings
• Interior and Exterior Dual Finish Options
Outswing Casement
Window
HINGED
LEFT
Thermal Break
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
•
•
•
•
•
•
•
•
Interior
Exterior
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME060
19
AA™4325 Series Windows
EC 97911-071
CLASS and GRADE
Architectural Grade AW-PG80-C
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S.2 / A440-05 / A440-08
FRAME DEPTH
3-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.080 Nominal Frame / .125" Nominal Vent
TYPICAL MAX. VENT SIZE
36" x 60"
TYPICAL MIN. VENT SIZE
19" x 24"
INFILL OPTIONS
1" and 1-3/4" (Other infill options available upon request.)
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Handles
OPTIONAL HARDWARE
Access Control Locks
Pole and Pole Ring
Limit Stop
Roto Operators
Multi-Point Locks
OTHER OPTIONS
Structural Mullions
Vertically or Horizontally Stacked
Insect Screens
Receptor and Sub Sill
Panning
Internal Blinds
Exterior or Interior Muntins
ADME060
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
TYPICAL CONFIGURATIONS
kawneer.com
© Kawneer Company, Inc., 2014
OUTSWING CASEMENT WINDOW
JANUARY, 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
20
kawneer.com
3-3/8"(86)
W.D.
O.D.
4
JAMB
4
JAMB
D.L.O.
D.L.O.
W.D.
5
JAMB
5
JAMB
ADME060
3-3/8"(86)
3/8"(10)
D.L.O.
D.L.O.
D.L.O.
1
HEAD
2
SILL
3
SILL
3-3/8"(86)
W.D.
O.D.
O.D.
3-3/8"(86)
W.D.
3/8"(10)
EC 97911-071
3-3/8"(86)
3/8"(10)
2 3
W.D.
3-1/4"(83)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
4
O.D.
3/8"(10)
1/2"(13)
3-1/4"(83)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
JANUARY, 2015
AA™4325 Series Windows
3-1/4"(83)
5
1
HEAD
TYPICAL ELEVATION
2
SILL
O.D.
3
SILL
21
OUTSWING CASEMENT WINDOW
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
1
3-1/4"(83)
AA™4325 Series Windows
EC 97911-071
A standard hinge for ventilators providing an
opening of up to 45°. An optional limit stop is
available to restrict hinge travel and limit vent
opening.
CAM HANDLE
Cast white bronze cam handles are an alternative
to standard multi-point locking for the operation
and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring
provide manual operation of ventilators located
above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction
with locking hardware for sash pole operation of
ventilators.
SASH POLE
A 3/4" diameter aluminum sash pole with a cast
white bronze pull down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional
cast white bronze Pole Hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of cam handles and multi-point locking cast
white bronze access control locks are offered for
managed control of vent operations.
Lock is operated with a manganese bronze
removable handle.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OUTSWING CASEMENT WINDOW
JANUARY, 2015
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
22
6-3/4"
(171.4)
4"
(101.6)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1-1/4"
(31.7)
kawneer.com
20-0793
4-1/8"
(107.7)
4"
(101.6)
S-11056
S-11055
3-PIECE MULLIONS
ADME060
S-11038
EC 97911-071
IF-1447
2-1/2"
(63.5)
3-3/4"
(95)
S-11038
2-1/2"
(63.5)
IF-1447
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JANUARY, 2015
AA™4325 Series Windows
RECEPTORS, SUB SILLS AND ANCHORING
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
S-071
S-071
IF-1448
2"
(51)
IF-1448
HEAD & JAMB RECEPTORS
4-1/16"
(103.2)
20-0793
ANCHOR
S-11056
S-11055
IF-1445
3-3/8"
(85.7)
H-11075
3-3/8"
(85.7)
3-1/8"
(79.4)
IF-1449
50-2130
SUB SILL
50-0973
23
PRE-SET PANNING
WRAP AROUND PANNING
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
PANNINGS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AA™4325 Series Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
24
JANUARY, 2015
EC 97911-071
SCALE : 3" = 1'-0"
(Nominal Dimensions Shown)
Note: 1" glazing infill shown, 1-3/4" similar.
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
25
THERMAL CHARTS
Generic Project Specific U-factor Example Calculation
(Percent of Glass will vary on specific products depending on sitelines)
51-3/4"
(1315)
5'-0"
(1524)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
3'-0"
(915)
27-3/4"
(705)
Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F
Total Daylight Opening
= 27-3/4" • 51-3/4" = 9.97ft2
Total Projected Area
= 3'-0" • 5'-0" = 15 ft2
Percent of Glass
= (Total Daylight Opening ÷ Total Projected Area)100
= (9.97 ÷ 15)100 = 66%
System U-factor vs Percent of Glass Area
(5.00)
0.85
0.80
(4.50)
0.75
N
0.60
0.55
0.53
0.50
0.45
0.35
(2.50)
(2.00)
0.30
0.20
70
66%
65
60
55
Percent of Glass Area
Based on 66% glass and center of glass (COG) U-factor of 0.42
System U-factor is equal to 0.53 Btu/hr • ft2 • °F
kawneer.com
(3.00)
0.40
0.25
75
(3.50)
ADME060
50
(1.50)
W
m2 • °C
System U-factor
© Kawneer Company, Inc., 2014
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
(4.00)
0.65
Btu
hr • ft2 • °F
System U-factor
COG
U-factor
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.70
E IGN
PL S
M E
A D
EX OR
F
T
O
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.90
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL CHARTS
FIXED WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.79)
0.12 (0.68)
0.10 (0.57)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
0.38 (2.16)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Btu
hr • ft2 • °F
System U-factor
26
System VT
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JANUARY, 2015
kawneer.com
AA™4325 Series Windows
EC 97911-071
Vision Area / Total Area (%)
ADME060
27
THERMAL CHARTS
FIXED WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
Thermal Transmittance (BTU/hr • ft • °F)
2
Overall U-Factor 4
0.48
0.50
0.46
0.49
0.44
0.47
0.42
0.46
0.40
0.44
0.38
0.42
0.36
0.41
0.34
0.39
0.32
0.38
0.30
0.36
0.28
0.35
0.26
0.33
0.24
0.31
0.22
0.30
0.20
0.28
0.18
0.27
0.16
0.26
0.14
0.24
0.12
0.22
0.10
0.21
FIXED WINDOW WITH 1" GLAZING
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1200mm wide by
1500mm high (47-1/4" by 59-1/16").
SHGC Matrix 2
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.64
0.75
0.64
0.70
0.60
0.70
0.60
0.65
0.56
0.65
0.55
0.60
0.52
0.60
0.51
0.55
0.47
0.55
0.47
0.50
0.43
0.50
0.43
0.45
0.39
0.45
0.38
0.40
0.35
0.40
0.34
0.35
0.30
0.35
0.30
0.30
0.26
0.30
0.26
0.25
0.22
0.25
0.21
0.20
0.18
0.20
0.17
0.15
0.13
0.15
0.13
0.10
0.09
0.10
0.09
0.05
0.05
0.05
0.04
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
28
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL CHARTS
FIXED WINDOW WITH 1-3/4" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
0.32 (1.82)
Btu
hr • ft2 • °F
System U-factor
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.80)
0.12 (0.68)
0.10 (0.57)
0.08 (0.45)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.22 (1.25)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
kawneer.com
ADME060
29
COG
VT
Vision Area / Total Area (%)
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
AA™4325 Series Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
30
JANUARY, 2015
EC 97911-071
FIXED WINDOW WITH 1-3/4" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
FIXED WINDOW WITH 1-3/4" GLAZING
Glass U-Factor 3
Overall U-Factor 4
0.32
0.33
0.30
0.32
0.28
0.30
0.26
0.28
0.24
0.27
0.22
0.25
0.20
0.23
0.18
0.22
0.16
0.20
0.14
0.19
0.12
0.17
0.10
0.15
0.08
0.13
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1200mm wide by
1500mm high (47-1/4" by 59-1/16").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.63
0.75
0.63
0.70
0.59
0.70
0.59
0.65
0.55
0.65
0.55
0.60
0.51
0.60
0.50
0.55
0.47
0.55
0.46
0.50
0.42
0.50
0.42
0.45
0.38
0.45
0.38
0.40
0.34
0.40
0.34
0.35
0.30
0.35
0.29
0.30
0.26
0.30
0.25
0.25
0.21
0.25
0.21
0.20
0.17
0.20
0.17
0.15
0.13
0.15
0.13
0.10
0.09
0.10
0.08
0.05
0.05
0.05
0.04
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
kawneer.com
ADME060
31
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL CHARTS
PROJECT-IN WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.79)
0.12 (0.68)
0.10 (0.57)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Btu
hr • ft2 • °F
System U-factor
32
System VT
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JANUARY, 2015
kawneer.com
AA™4325 Series Windows
EC 97911-071
Vision Area / Total Area (%)
ADME060
33
THERMAL CHARTS
PROJECT-IN WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
Thermal Transmittance (BTU/hr • ft • °F)
2
Overall U-Factor 4
0.47
0.49
0.46
0.48
0.44
0.47
0.42
0.46
0.40
0.45
0.38
0.44
0.36
0.42
0.34
0.41
0.32
0.40
0.30
0.39
0.28
0.38
0.26
0.36
0.24
0.35
0.22
0.34
0.20
0.33
0.18
0.33
0.16
0.32
0.14
0.31
0.12
0.30
0.10
0.28
PROJECT-IN WINDOW
WITH 1" GLAZING
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1500mm wide by
600mm high (59-1/16" by 23-5/8").
SHGC Matrix 2
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.49
0.75
0.47
0.70
0.46
0.70
0.44
0.65
0.42
0.65
0.41
0.60
0.39
0.60
0.38
0.55
0.36
0.55
0.35
0.50
0.33
0.50
0.32
0.45
0.30
0.45
0.28
0.40
0.27
0.40
0.25
0.35
0.23
0.35
0.22
0.30
0.20
0.30
0.19
0.25
0.17
0.25
0.16
0.20
0.14
0.20
0.13
0.15
0.11
0.15
0.09
0.10
0.08
0.10
0.06
0.05
0.04
0.05
0.03
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
34
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL CHARTS
PROJECT-IN WINDOW WITH 1-3/4" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
0.32 (1.82)
0.30 (1.71)
Btu
hr • ft2 • °F
System U-factor
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.18 (1.02)
0.16 (0.91)
0.14 (0.80)
0.12 (0.68)
0.10 (0.57)
0.08 (0.45)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.20 (1.14)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
kawneer.com
ADME060
35
COG
SHGC
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
Vision Area / Total Area (%)
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
AA™4325 Series Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
36
JANUARY, 2015
EC 97911-071
PROJECT-IN WINDOW WITH 1-3/4" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
Vision Area / Total Area (%)
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
PROJECT-IN WINDOW WITH 1-3/4" GLAZING
Glass U-Factor 3
Overall U-Factor 4
0.32
0.34
0.30
0.33
0.28
0.32
0.26
0.30
0.24
0.29
0.22
0.28
0.20
0.27
0.18
0.25
0.16
0.24
0.14
0.23
0.12
0.22
0.10
0.21
0.08
0.19
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1500mm wide by
600mm high (59-1/16" by 23-5/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.48
0.75
0.47
0.70
0.45
0.70
0.44
0.65
0.42
0.65
0.41
0.60
0.39
0.60
0.38
0.55
0.36
0.55
0.35
0.50
0.33
0.50
0.32
0.45
0.29
0.45
0.28
0.40
0.26
0.40
0.25
0.35
0.23
0.35
0.22
0.30
0.20
0.30
0.19
0.25
0.17
0.25
0.16
0.20
0.14
0.20
0.13
0.15
0.10
0.15
0.09
0.10
0.07
0.10
0.06
0.05
0.04
0.05
0.03
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
kawneer.com
ADME060
37
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL CHARTS
PROJECT-OUT WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
0.47 (2.67)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
0.18 (1.02)
0.16 (0.91)
0.14 (0.79)
0.12 (0.68)
0.10 (0.57)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Btu
hr • ft2 • °F
System U-factor
38
System VT
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JANUARY, 2015
kawneer.com
AA™4325 Series Windows
EC 97911-071
Vision Area / Total Area (%)
ADME060
39
THERMAL CHARTS
PROJECT-OUT WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
Thermal Transmittance (BTU/hr • ft • °F)
2
Overall U-Factor 4
0.48
0.55
0.46
0.54
0.44
0.53
0.42
0.52
0.40
0.51
0.38
0.50
0.36
0.48
0.34
0.47
0.32
0.46
0.30
0.45
0.28
0.44
0.26
0.43
0.24
0.41
0.22
0.40
0.20
0.39
0.18
0.39
0.16
0.38
0.14
0.37
0.12
0.35
0.10
0.34
PROJECT-OUT WINDOW
WITH 1" GLAZING
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1500mm wide by
600mm high (59-1/16" by 23-5/8").
SHGC Matrix 2
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.49
0.75
0.47
0.70
0.46
0.70
0.44
0.65
0.43
0.65
0.41
0.60
0.40
0.60
0.38
0.55
0.37
0.55
0.35
0.50
0.33
0.50
0.32
0.45
0.30
0.45
0.28
0.40
0.27
0.40
0.25
0.35
0.24
0.35
0.22
0.30
0.21
0.30
0.19
0.25
0.18
0.25
0.16
0.20
0.14
0.20
0.13
0.15
0.11
0.15
0.09
0.10
0.08
0.10
0.06
0.05
0.05
0.05
0.03
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
40
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL CHARTS
PROJECT-OUT WINDOW WITH 1-3/4" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
0.32 (1.82)
0.30 (1.71)
Btu
hr • ft2 • °F
System U-factor
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.18 (1.02)
0.16 (0.91)
0.14 (0.80)
0.12 (0.68)
0.10 (0.57)
0.08 (0.45)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.20 (1.14)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
kawneer.com
ADME060
41
COG
SHGC
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
Vision Area / Total Area (%)
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
AA™4325 Series Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
42
JANUARY, 2015
EC 97911-071
PROJECT-OUT WINDOW WITH 1-3/4" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
Vision Area / Total Area (%)
AA™4325 Series Windows
JANUARY, 2015
EC 97911-071
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
PROJECT-OUT WINDOW WITH 1-3/4" GLAZING
Glass U-Factor 3
Overall U-Factor 4
0.32
0.35
0.30
0.34
0.28
0.32
0.26
0.31
0.24
0.30
0.22
0.29
0.20
0.27
0.18
0.26
0.16
0.25
0.14
0.24
0.12
0.23
0.10
0.21
0.08
0.20
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1500mm wide by
600mm high (59-1/16" by 23-5/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.75
0.48
0.75
0.47
0.70
0.45
0.70
0.44
0.65
0.42
0.65
0.41
0.60
0.39
0.60
0.38
0.55
0.36
0.55
0.35
0.50
0.33
0.50
0.32
0.45
0.29
0.45
0.28
0.40
0.26
0.40
0.25
0.35
0.23
0.35
0.22
0.30
0.20
0.30
0.19
0.25
0.17
0.25
0.16
0.20
0.14
0.20
0.13
0.15
0.10
0.15
0.09
0.10
0.07
0.10
0.06
0.05
0.04
0.05
0.03
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
kawneer.com
ADME060
43
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
AA™4325 Series Windows
BLANK PAGE
ADME060
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
44
JANUARY, 2015
EC 97911-071
Similar pages