PTCHP12S - 265 V Series Datasheet

PTCHP12S - 265 V Series
www.vishay.com
Vishay BCcomponents
PTC Thermistors for Heating Application
FEATURES
• Ag-metalization suitable for clamping
• Self-regulating surface temperature at voltages
from 90 VAC up to 265 VAC
• Self-protecting against over-heating due to
PTC effect
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
DESCRIPTION
QUICK REFERENCE DATA
PARAMETER
VALUE
UNIT
Resistance value at 25 °C
1200
Ω
Tolerance on R25
± 35
%
Maximum voltage (RMS or DC)
265
V
1
A
Maximum inrush current
Switching temperature
50 to 150
Operating temperature range
-40 to 85
Storage temperature
-40 to 155
These directly heated thermistors are made from doped
BaTiO3 ceramic material with a large positive temperature
coefficient in a defined temperature range. The silver
metalized surfaces will stabilize at a specific temperature
less dependent on applied voltage or thermal loading.
MOUNTING
Can be mounted by force clamping, single side loaded or
dual sided. Soldering on the surfaces is not recommended.
°C
APPLICATIONS
• Thermal actuators and valves
• Warming plates
• Vaporizers
• Heaters
ELECTRICAL DATA AND ORDERING INFORMATION
R25
(Ω)
Tswitch
(°C)
Tsurf (1) at 230 VAC
(°C)
ORDERING PART NUMBERS
1200
50
100
PTCHP12S050HYE
1200
90
125
PTCHP12S090HYE
1200
110
140
PTCHP12S110HYE
1200
130
160
PTCHP12S130HYE
1200
150
180
PTCHP12S150HYE
Note
(1) Measured in a low thermal load set-up with the ceramic clamped between a 4 mm diameter stainless steel surface temperature probe on
one side in the center of the metallized surface and 4 mm spring loaded round contact at the other side
DIMENSIONS in millimeters
D
T
D
T
11.8 ± 0.2
2.0 ± 0.2
Document Number: 29093
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Revision: 26-Nov-15
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000