Datasheet

DG82
micro plug-in/pcb automotive relay
• Industry Standard micro-ISO plug-in relay
• Up to 120A 12VDC inrush capability
• PCB Mounting option
• Cost effective
• RoHS Compliant
Contacts
Contact number & arrangement
SPST-NO (1 Form A); SPDT (1 Form C)
Contact material
AgNi0.15; AgNi90/10; AgSnOInO; AgCdO
Max. switching voltage
DC 16VDC (current dependent - see Fig 3)
Rated load (max. continuous current)
Max. switching current3
DC1 40A/12VDC (Normally open); 30A/12VDC (Normally closed)
Make 90A (120A:AgSnOInO) (Normally open); 45A (Normally closed)
Break 40A (Normally open contact) / 30A (Normally closed contact)
Minimum load
AgNi0.15: 0.1A/12VDC, AgSnOInO: 05A/12VDC
Initial resistance
50mΩ, max. at 0.1A/6VDC
Coil
Rated voltage
Must release voltage
Operating range of supply voltage
Rated power consumption
DC 6...24V
≥0.1Un
See coil table 1
DC Approx. 1.2W (SPST-NO) / 1.5W (SPDT); 1.81W with resistor
Insulation
Insulation resistance
100MΩ at 500VDC, 50%RH
Dielectric strength
coil to contact 500Vrms, 1min
contact to contact 500Vrms, 1min
General Data
Operating time (typical)
ms 9
Release time (typical)
ms 7
Electrical Life2
ops 2 x 105
Mechanical life
ops 1 x 107
Dimensions
Weight
L x W x H 23.5 x 15.7 x 26.0 mm (excluding terminals)
Plug-in: 21g / PCB: 19g approx.
Ambient temperature
storage -40 to 155°C
operating -40 to 125°C (Derate above 85°C - consult factory)
Shock resistance
Functional: 20g 11ms; Destructive: 100g
Vibration resistance
DA 1.27mm 10-40Hz / 40-70Hz:5g / DA 0.5mm 100-500Hz: 10g
Page 1 of 3 Ref: DG82 102315JHM
www.aecsensors.com
Sales Department Tel: (888) 847-6552
Specifications are liable to change without notice. E&OE.
DG82
micro plug-in/pcb automotive relay
Coil Data
Table 1
Coil Resistance (Ω) ±10%
Coil Voltage
Code
Nominal
Voltage
(VDC)
1006
6
32
1012
12
123
1024
24
483
1 Form A
1 Form C
Must
Operate
Voltage
Max. (VDC)
25
Allowable Voltage (VDC)*
1 Form A
1 Form C
Must
release
voltage min.
(VDC)
Parallel
Resistor
(optional)
(Ω)
170
3.6
10.4
9.2
0.6
97
7.2
20.4
18.1
1.2
680
384
14.4
40.4
36.0
2.4
2720
* At ambient temperature of 85’C, maximum allowable voltage should be reduced by 28%
Ordering codes
Contact
material
Type
D
G
8
2
Contact
arrangement
-
Cover protection and
mounting
-
Coil code
Options
-
-
Contact material
10
-
AgCdO
20
-
AgNi 90/10
70
-
AgSnOInO
80
-
AgNi 0.15
See coil table 1
Contact arrangement
11
-
SPDT (1 C/O, 1 Form C)
21
-
SPST-NO (1N/O, 1 Form A)
Cover protection category
3
-
in cover, sealed - IP67
7
-
in cover, dust cover - IP54
Connection mode
5
-
for PCB
6
-
Flat Blades
Coil Options
Nil
-
UL Class F coil insulation
H
-
UL Class H insulation for higher ambient temperatures - consult factory.
Parallel Component Options
Nil
-
No option
R
-
Resistor (see Table 1 for values)
D
-
Diode (+85 / -86)
DR
-
Diode reversed (-85 / + 86) - standard
BD
-
Bidirectional diode
Page 2 of 3 Ref: DG82 102315JHM
www.aecsensors.com
Sales Department Tel: (888) 847-6552
Specifications are liable to change without notice. E&OE.
DG82
micro plug-in/pcb automotive relay
Overall Dimensions
Fig. 1
Dimensions in mm
PCB Mounting Dimensions
Wiring Diagrams (Bottom View)
Fig. 3
Reference Curves
SPDT
(1 Form C)
Switching Current (A)
SPST-NO
(1 Form A)
Fig. 2
Switching Voltage (VDC)
Mounting Holes (Bottom View)
Notes:
1: All parameters, unless otherwise specified, are measured at ambient temperature of 23ºC.
2: Electrical life obtained at resistive or inductive load at 40A, 15VDC with suitable arc suppression circuit attached and with operating
frequency of 1 op/sec.
3: Maximum make current refers to lamp load inrush current.
Page 3 of 3
Ref: DG82 102315JHM
American Electronic Components Inc., 1101 Lafayette St. Elkhart, IN46516
www.aecsensors.com
Sales Department Tel: (888) 847-6552
Specifications are liable to change without notice. E&OE.
Similar pages