Datasheet

SURFACE MOUNT
HIGH REPEATABILITY
8 GHz
TO-5 RELAYS
SIGNAL INTEGRITY TO 12 Gbps
DPDT
SERIES
DESIGNATION
RELAY TYPE
SGRF312
Repeatable, RF TO-5 relay
SERIES
SGRF312
PERFORMANCE FEATURES
INTERNAL CONSTRUCTION
The ultraminiature SGRF312 relays are designed to improve upon
the GRF312 relay's high frequency performance. The SGRF312
relays feature a unique ground shield that isolates and shields
each lead to ensure excellent contact-to-contact resistance and
pole-to-pole isolation. The SGRF312 offers monotonic insertion
loss to 8 GHz. This improvement in RF insertion loss over the
frequency range makes these relays highly suitable for use in
attenuator and other RF circuits. The SGRF312 features:
• High repeatability.
• Broader bandwidth.
• Metal enclosure for EMI shielding.
ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
Temperature
(Ambient)
• High isolation between control and signal paths.
Storage
–65°C to +125°C
Operating
–55°C to +85°C
• Highly resistant to ESD.
CONSTRUCTION FEATURES
Vibration
(General Note 1)
10 g’s to 500 Hz
Shock
(General Note 1)
30 g’s,
6ms half sine
Enclosure
Hermetically sealed
Weight
0.09 oz. (2.55g) max.
• Uni-frame motor design provides high magnetic efficiency
and mechanical rigidity.
PART NUMBERING SYSTEM FOR SGRF RELAYS
• Minimum mass components and welded construction provide
maximum resistance to shock and vibration.
SGRF312
Relay Series
Ground Pin
Option
Y
-
The following unique construction features and manufacturing
techniques provide excellent resistance to environmental
extremes and overall high reliability.
• Advanced cleaning techniques provide maximum assurance
of internal cleanliness.
5
Coil Voltage
• Gold-plated precious metal alloy contacts ensure reliable
switching.
• Hermetically sealed.
• Solderable leads.
© 2009 TELEDYNE RELAYS
(800) 284-7007 • www.teledynerelays.com
SGRF312 Page 1
SGRF312\072009\Q3
SERIES SGRF312
TYPICAL RF CHARACTERISTICS (See RF Notes)
Isolation Across Contacts (RF Note 3)
Insertion Loss (RF Note 4)
0
0
-0.5
P2NC
-10
P2NO
Insertion Loss (dB)
-1
Isolation (dB)
-20
-30
-40
-1.5
-2
-2.5
P1NC
-3
P1NO
-50
-3.5
-4
-60
0
1
2
3
4
5
6
7
0
8
1
2
3
Frequecny(GHz)
4
5
6
7
8
Frequency (GHz)
VSWR (RF Note 4)
Pole to Pole Isolation (RF Note 4)
0
4
-10
P1NC
3.5
-20
P1NO
-30
Isolation (dB)
VSWR
3
2.5
2
-40
-50
-60
-70
P-P-DE
-80
1.5
P-P-E
-90
1
-100
0
1
2
3
4
5
6
7
8
0
1
2
3
Frequency (GHz)
4
5
6
7
8
Frequency (GHz)
Time Response (RF Note 4)
1.1
0.9
90%
Volt
0.7
37ps reference
0.5
62.3ps propagation delay time
0.3
51.1ps pulse rise time
10%
0.1
-0.1
-100
0
100
200
300
400
500
600
700
800
900
Time (ps)
RF NOTES
a. Fixture: .031" copper clad, reinforced PTFE, RT/duroid® 6002 with SMA connectors.
(RT/duroid® is a registered trademark of Rogers Corporation.)
b. RF ground shield is soldered to PCB RF ground plane.
c. Room ambient temperature.
d. Terminals not tested were terminated with 50-ohm load.
e. Contact signal level: –10 dBm.
f. No. of test samples: 2.
Data presented herein represents typical characteristics and is not intended for use as specification limits.
Data is per pole, except for pole-to-pole data.
Data is the average from readings taken on all open contacts.
Data is the average from readings taken between poles with coil energized and de-energized.
Data is the average from readings taken on all closed contacts.
Test fixture effect de-embedded from frequency and time response data.
1. Test conditions:
2.
3.
4.
5.
6.
7.
SGRF312 Page 2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2009 TELEDYNE RELAYS
SGRF312\072009\Q3
SERIES SGRF312
GENERAL ELECTRICAL SPECIFICATIONS (@ 25 ºC unless otherwise noted)
Contact Arrangement
2 Form C (DPDT)
Rated Duty
Continuous
Contact Resistance
0.15 Ω max. initial (measured 1/8" from the header)
Contact Load Rating
Resistive: 1Amp/28Vdc
Low level: 10 to 50 μA, 10 to 50 mV
Contact Life Ratings
10,000,000 cycles (typical) at low level
Coil Operating Power
450 mW typical @ nominal rated voltage
Operate Time
4.0 mS max.
Release Time
3.0 mS max.
Intercontact Capacitance
0.4 pF typical
Insulation Resistance
1,000 MΩ min. between mutually isolated terminals
Dielectric Strength
350 Vrms (60 Hz) @ atmospheric pressure
DETAILED ELECTRICAL SPECIFICATIONS (@25°C)
BASE PART NUMBERS
SGRF312-5
SGRF312-12
Coil Voltage, Nominal (Vdc)
5.0
12.0
Coil Resistance (Ohms ±20%)
50
390
Pick-up Voltage (Vdc max.)
3.6
9.0
OUTLINE DIMENSIONS
BEFORE
LASER WELD
NOTES
1. Dimensions are in inches. Metric equivalents in millimeters are shown in [ ].
2. For best RF performance, solder bottom of RF ground shield to PCB RF ground plane.
3. Positions 5 (Y) and 10 (Z) are for uninsulated case ground pin options.
GENERAL NOTES
1.
2.
3.
4.
Relays will exhibit no contact chatter in excess of 10 μsec or transfer in excess of 1 μsec.
Relays may be subjected to 260 ºC peak solder reflow temperature, 1 minute, 3 passes.
Butt-lead ends are coplanar within .003” (0.08 mm).
Application notes available for PCB mounting information.
© 2009 TELEDYNE RELAYS
(800) 284-7007 • www.teledynerelays.com
SGRF312 Page 3
SGRF312\072009\Q3
Similar pages