499J

MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
6 PIN FLIP−CHIP
1.72x1.22mm, 0.5 PITCH
CASE 499J−01
ISSUE O
A1
DATE 05 FEB 2004
SCALE 4:1
4X
0.10 C
TERMINAL A1
LOCATOR
ÈÈ
ÈÈ
D
A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
B
E
MILLIMETERS
DIM MIN
MAX
A
−−− 0.700
A1 0.210 0.270
A2 0.380 0.430
D
1.720 BSC
E
1.220 BSC
b
0.290 0.340
e
0.500 BSC
D1
1.000 BSC
TOP VIEW
A2
A1
0.10 C
C
A
0.05 C
SIDE VIEW
GENERIC
MARKING DIAGRAM*
SEATING
PLANE
È
D1
TBD
e
B
6X
b
A
0.05 C A B
0.03 C
1
2
3
xx
A
WL, L
YY, Y
WW, W
e
BOTTOM VIEW
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
*This information is generic. Please refer
to device data sheet for actual part
marking.
DOCUMENT NUMBER:
STATUS:
NEW STANDARD:
98AON13950D
ON SEMICONDUCTOR STANDARD
 Semiconductor Components Industries, LLC, 2002
October, DESCRIPTION:
2002 − Rev. 0
Electronic versions are uncontrolled except when
accessed directly from the Document Repository. Printed
versions are uncontrolled except when stamped
“CONTROLLED COPY” in red.
http://onsemi.com
6 PIN FLIP−CHIP, 1.72x1.22mm,
1 0.5 PITCH
Case Outline Number:
PAGE 1 OFXXX
2
DOCUMENT NUMBER:
98AON13950D
PAGE 2 OF 2
ISSUE
O
REVISION
RELEASED FOR PRODUCTION. REQ. BY S. CHANG
DATE
05 FEB 2004
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make
changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
 Semiconductor Components Industries, LLC, 2004
February, 2004 − Rev. 01O
Case Outline Number:
499J
Similar pages