BR1569, Analog ICs Integrated Solutions Applications - Brochure

Freescale Semiconductor, Inc.
Quarter 2, 2015
BR1569 Rev. 15
Applications Analog and
Power Management
Making embedded systems better with robust
reliable performance
Applications- Robust, Reliable, Performance
GENERIC SYSTEM DIAGRAMS
• MOTOR CONTROL — Regulates the speed, rotation, and torque of a motor
• MOTION CONTROL — Governs the physical displacement movement, location, or position of a mechanical assembly, driven by an intermittent duty
motor
• STATIC LOAD CONTROL — Fully or partially powers-up the elements of a relatively constant load
• POWERTRAIN AND ENGINE MANAGEMENT — Provides functionality for controlling and monitoring engine and transmission system loads
• NETWORK COMMUNICATIONS — Provides device-to-device communication within a system
• EMBEDDED MCU PLUS POWER — Provides an integrated single package solution with MCU, Voltage Regulation, Power Actuation, and LIN bus
transceiver
• BATTERY CHARGER — Provides high voltage accuracy over the full temperature range due to the different charging process
• RADAR SYSTEMS — Provides long- and mid-range functionality, allowing automotive systems to monitor the environment around the vehicle to help
prevent crashes
• POWER MANAGEMENT — Converts system input power to the voltages and currents required by the MCU and DSP
• BATTERY MANAGEMENT — Provides highest performance and accuracy, as well as exceptional configuration flexibility
Applications
Analog, Mixed-Signal, and Power Management
MOTOR CONTROL GENERIC SYSTEM DIAGRAM
Motor control is the function of regulating the speed, rotation, and torque of a motor.
TYPICAL
APPLICATIONS:
LOOP CONTROL
SCHEMA:
POWER CONTROL
SCHEMA:
MOTOR TYPES:
• Blowers
• Speed
• ON/OFF
• DC 3-Phase Brushless
• Fans
• Torque/Current
• PWM
• Universal
• Vacuums
• Voltage
• Linear
• AC Induction
• Pumps
• Rotation (CW/CCW)
• Volts/Hertz (V/f)
• Switched Reluctance
• Compressors
• None (Open Loop)
• Rotating Vector
• Stepper
• DC Brush Commutator
• Phase Angle
• Golf Carts
• Scooters
• Electric Wheelchairs
• Electric Boats
• Conveyors
• Shakers
• Vibrators
• Mixers
• Shredders
• Winches
• Elevators
• Treadmills
• Power Tools
CONSIDER:
CM0902
33399
33660
33661
33662
33663
33780
33897
33901/34901
POWER SUPPLY
• S08
POWER
MANAGEMENT
• S12
• i.MX6/7
• Qorivva 32-bit
INTER-MODULE
COMMUNICATION
SPI or PARALLEL
CONTROL
• Kinetis
NETWORK
TRANCEIVERS
SYSTEM INPUT
SIGNAL
CONDITIONING
33910
33730
33911
33742
33989
33889
34700
33903/34903
34704
33904/34904
34713
33905/34905
34716
FS6407
34717
FS6408
34VR500
FS4409
PF0100
33907
PF0200
33908
PF3000
33909
MCU
or
DSP
or
ASSP
CONTROLLER
2
POWER
ACTUATION
POWER
ROTOR POSITION
(optional)
MOTOR
FEEDBACK
SIGNAL
CONDITIONING
33793
33811
33972/34972
33975/34975
33978/34978
PT2000
33800
33810
33816
33879
33880
33882
33886
33887
33899
33931/34931
MECH
ASSY
33HB2000
33HB2001
33GD3000
34GD3000
SB0400
SB0400
SB0401
34SB0410
34SB0800
33932/34932
33937/34937
33926
33996
33999
17510
17529
17533
17C724
12XS2
12XS3
12XS6
12XSB
12XSC
12XSF
24XS4
36XSD
33793
33811
33972/34972
33975/34975
33978/34978
See “Embedded MCU Plus Power Generic System Diagram” on page 7.
Analog, Mixed-Signal, and Power Management
Applications
MOTION CONTROL GENERIC SYSTEM DIAGRAM
Motion control is the function of governing the physical displacement, movement, location, or position of a mechanical assembly driven by an
intermittent duty motor.
TYPICAL
APPLICATIONS:
• Printer Paper Handler
• CNC Machining
• Conveyors
• Robotics
• Shakers
• Scanners
POWER CONTROL
SCHEMA:
• Rotation (CW/
CCW)
• ON/OFF
• DC Brush
Commutator
• PWM
• Brushless DC
• Linear
• Stepper
• Step Count
• Stepper (Pulse &
Hold)
• Linear
• Hard Automation
• Consumer Portable
Products
• Position
• Power-Assisted
• Digital Cameras
• Operator Controls
• Printers
• Operator (Open
Loop)
• Process Controls
• Office Equipment
• Autopilots
• Industrial Controller
• Guidance/Steering
• Force
• Controls
• Spot Welding
• Servos and Radio
• Fluid Coating
• Controls
• Flight Simulator
• Antenna Rotors
• Temperature Control
• Dish Positioners
• Brake Pressure
• Power Adjustable
• Laser Cutting
• Beds
• Bottle Moulding
• Remote Pan and Tilt
• Filling Pressure
• HVAC Mix Louvers
MOTOR TYPES:
LOOP CONTROL
SCHEMA:
• Solenoid
• Servos
• Mounts
CONSIDER:
CM0902
33399
33660
33661
33662
33663
33780
33897
33901/34901
POWER SUPPLY
• S08
POWER
MANAGEMENT
• S12
• i.MX6/7
• Qorivva 32-bit
INTER-MODULE
COMMUNICATION
SPI or PARALLEL
CONTROL
• Kinetis
NETWORK
TRANCEIVERS
SYSTEM INPUT
33730
33910
33742
33911
33889
33912
33903/34903
33989
33904/34904
34700
33905/34905
34704
FS6407
34713
FS6408
34716
FS4409
34717
33907
34VR500
33908
MCU
or
DSP
or
ASSP
CONTROLLER
SIGNAL
CONDITIONING
See “Embedded MCU Plus Power Generic System Diagram” on page 7.
POWER
ACTUATION
POWER
ROTOR POSITION
(optional)
33931/34931
33932/34932
33937/34937
33996
33999
34933
SB0400
SB0401
33HB2000
33HB2001
33GD3000
34GD3000
17510
17529
17533
17C724
12XS2
12XS3
12XS6
12XSB
12XSC
12XSF
24XS4
36XSD
MOTOR/
PUMP
FEEDBACK
SIGNAL
CONDITIONING
33793
33811
33972/34972
33975/34975
33978/34978
PT2000
SB0410
SB0800
33800
33810
33816
33879
33880
33882
33886
33887
33899
33926
MECH
ASSY
33793
33811
33972/34972
33975/34975
3
Applications
Analog, Mixed-Signal, and Power Management
STATIC LOAD CONTROL GENERIC SYSTEM DIAGRAM
Static load control is the function of fully or partially powering-up the elements of a relatively constant load.
TYPICAL APPLICATIONS: LOOP CONTROL
SCHEMA:
• Security Systems
• Current
• HVAC
POWER CONTROL
SCHEMA:
STATIC LOAD TYPES:
• ON/OFF
• Heating Elements
• Incandescent Lamps
• Water Heaters
• Voltage
• PWM
• LEDs/Lasers
• Charging Systems
• Sensor Feedback
• PFM
• Lighting Displays
• Limit Switch
(Bang-Bang)
• Linear
• Ultrasonic
Transducers
• Phase Angle
• Piezo Transducers
• Score Boards
• None (Open Loop)
• Irrigation Control
• Induction Coils
• Sirens/Horns/Bells
• Programmable
Thermostats
• Gaming Machines
• Industrial Controls
• Automotive Body
Electronics
• Large Building Automation
• White Goods Appliances
• Automotive Safety
Systems
• LED Backlighting/Displays
CONSIDER:
• S08
33CM0902/34CM0902
33399
33660
33661
33662
33663
33780
33897
33901/34901
POWER SUPPLY
POWER
MANAGEMENT
• S12
• i.MX6/7
• Qorivva 32-bit
• Kinetis
INTER-MODULE
COMMUNICATION
NETWORK
TRANCEIVERS
SYSTEM INPUT
SIGNAL
CONDITIONING
33910
33730
33911
33742
33912
33889
33903/34903 33989
33904/34904 34700
33905/34905 34704
34VR500
FS6407
PF0100
FS6408
PF0200
FS4409
PF3000
33907
33908
33909
PARALLEL
I/O
POWER
PARALLEL ACTUATION
I/O
MCU
or
DSP
or
ASSP
CONTROLLER
SPI I/O
SPI I/O
33800
33810
33811
33879
33880
33882
33931/34931
33932/34932
33996
33999
34844
12XS2
12XS3
12XS6
12XSB
12XSC
12XSF
24XS4
36XSD
POWER
ACTUATION
POWER
ACTUATION
POWER
ACTUATION
FEEDBACK
SIGNAL
CONDITIONING
33793
33811
33972/34972
33975/34975
33978/34978
4
33793
33811
33972/34972
33975/34975
See “Embedded MCU Plus Power Generic System Diagram” on page 7.
Analog, Mixed-Signal, and Power Management
Applications
POWERTRAIN AND ENGINE MANAGEMENT SYSTEM DIAGRAM
These components represent devices that are designed to function in the automotive environment. They provide the functionality needed for
controlling and monitoring engine and transmission systems loads and inputs. The functions available range from alternator voltage regulator
control to Low-side switches, H-Bridge drivers, MOSFET/IGBT Pre-drivers, switch and solenoid monitoring, and more.
TYPICAL
APPLICATIONS:
LOOP CONTROL
SCHEMA:
POWER CONTROL
SCHEMA:
LOAD TYPES:
• Marine Engine
• Current
• ON/OFF
• Heating Elements
• Boat Motor
• Voltage
• PWM
• LEDs/Lasers
• Jet Ski Engine
• Sensor Feedback
• PFM
• Ultrasonic
• ATV / Motorcycle Engine
• Linear
• Transducers
• Industrial Engines
• Limit Switch
(Bang-Bang)
• Phase Angle
• None (Open Loop)
• Piezo Transducers
• Heavy Equipment
• Incandescent Lamps
• Induction Coils
• Automobile Engines
(2-12 cylinders)
• Sirens/Horns/Bells
Powertrain Controller
Loads
Analog / Digital Inputs
Main MCU
Gasoline and Diesel
33811
33975/34975
33978/34978
Cam Position
Clutch/Break
Speed
CONSIDER:
Timed Inputs
• Kinetis
Gasoline and Diesel
• S12XE
Accelerator
• S12P
Mass Air Flow
• S12XS
Battery
• Qorivva
Temperatures
Oxygen Sensors
33811
33975/34975
33978/34978
912_637
9Z1_638
Gasoline Only
Throttle Position
Signal Monitoring and Conditioning
Crank Speed
Power
DMA
Injector
Drivers
Ext
Bus
COM
Ignition Plugs (up to 12)
Diesel Only
Glow Plugs (up to 12)
Gasoline Only
Throttle Control
Diesel Only
EGR Positioner, Valves Control
Flash
Loads
Safety Micro
HC08, S08, S12
Power
Management
IC
COM ICs
HS CAN
LIN
FlexRay
Ethernet
Gasoline and Diesel
Output
Drivers
Relays
Tachometer Counter
Oxygen Heaters
33907
33908
33730
33909
Fuel Pump
Dashboard Lamps
Recirculation Valves
Knock Sensor
Gasoline Only
Diesel Only
Cylinder Pressure
CAN BUS
Rail Pressure
Injectors (up to 12)
Gasoline Only
Ignition
Pre-drivers
H-Bridge
Drivers
Timers
eTPU +
eMOS
Gasoline and Diesel
912_P812
912_S812
912_637
9Z1_638
33810
33811
33812
33813
33814
33816
912_P812
912_S812
PT2000
12XS2
12XS3
12XS6
12XSB
12XSC
12XSF
24XS4
36XSD
33800
33810
33812
33937/34937
Cam Control
Fuel Tank Valves
Intake Control
Diesel Only
33899
33926
33931/34931
33932/34932
Fan Control
Rail Pressure Control
5
Applications
Analog, Mixed-Signal, and Power Management
NETWORK COMMUNICATIONS SYSTEM DEVICES
Network communication provides information between two or more devices in a system.
TYPICAL
APPLICATIONS:
COMMUNICATIONS
SCHEMA:
• Aircraft Systems
• Bidirectional
• Antenna Controllers
• Combined Power &
Signaling
Error Detection
• Appliances
• Automotive Body
Electronics
• Fault Tolerant
• Automotive Safety
Systems
• Full/Half Duplex
• Conveyors
• Predictive
• Elevators
• Gaming Machines
• Single Ended/
Differential
• Heating & Cooling
• Single/Multi Master
• Irrigation Control
• Single/Multi Slave
• Lighting
• Timing Critical
• Machinery/Robotics
• Voltage/Current
Signaling
• Hi/Med/Low Speed
• Score Boards
• Security Systems
• Vending Machines
• Watercraft Systems
• Water Heaters
DSI2
Sensor
Interface
33784
DSI 2.02
Bus
Slave
Pressure
Sensor
33784
DSI 2.02 Bus
4X
Accelerometer
CONSIDER:
• S08
• S12
• Qorivva 32-bit
• Kinetis
Remote
Modules
ISO9141 Bus
Remote
Modules
LS CAN Bus
33889
LIN Bus
DSI
Bus
33793
DSI Bus
2X
33660
33897
HS CAN Bus
Slave
DBus Master
33780
33790
SW CAN Bus
Remote
Modules
Remote
Modules
6
PSI5 Bus Master
33789
DSI2 Bus Master
33781
Remote
Modules
Pressure
Sensor
33742
33901
33903
33904
33905
33907
33908
33989
CM0902
33661
33662
33663
33903
33905
33907
33908
33909
33910
33911
33912
MCU
SPI LOGIC
ISO9141 LOGIC
VDD,VIO
CAN LOGIC
LIN LOGIC
DSI
Sensor
Interface
33793
Accelerometer
Analog, Mixed-Signal, and Power Management
Applications
EMBEDDED MCU PLUS POWER GENERIC SYSTEM DIAGRAM
Motor control is the function of regulating the speed, rotation and torque of a motor.
TYPICAL
APPLICATIONS:
LOOP CONTROL
SCHEMA:
POWER CONTROL
SCHEMA:
MOTOR TYPES:
• Blowers
• Speed
• ON/OFF
• DC 3-Phase Brushless
• Fans
• Torque/Current
• PWM
• Universal
• Pumps
• Voltage
• Linear
• 2-Phase Stepper
• Power Seats
• Rotation (CW/CCW)
• Volts/Hertz
• Power Windows
• None (Open Loop)
• DC Brush Commutator
• Power Door Locks
• HVAC Doors/Vents
• Power Sunroof
• Side-view Mirrors
• Keypad
• Light Leveling
• Adaptive Lighting
33CM0902/34CM0902
33399
33660
33661
33662
33663
33901/34901
908E621
908E622
908E624
908E625
908E626
912_634
912_637
9Z1_638
EMBEDDED:
• S12 MagniV
• S12Z
INTER-MODULE
COMMUNICATION
• S12
NETWORK
TRANCEIVERS
SYSTEM INPUT
SIGNAL
CONDITIONING
POWER
LOADS
POWER
ACTUATION
LIN P/L
EMBEDDED MCU
+
POWER
CONTROLLER
POWER SUPPLY
33793
33811
33972/34972
33975/34975
33978/34978
ROTOR POSITION
(optional)
MOTOR CURRENT
(optional)
MOTOR
FEEDBACK
SIGNAL
CONDITIONING
MECH
ASSY
33793
33811
33972/34972
33975/34975
33978/34978
7
Applications
Analog, Mixed-Signal, and Power Management
BATTERY CHARGER
Portable Navigation Devices (PNDs) are expanding their reach to be embedded in everything from smartphones to auto infotainment
systems. Battery Charger provides flexible solutions to develop innovative navigation devices with wide range of features.
TYPICAL APPLICATIONS:
CHARGE CURRENT TYPES:
• Internet of Things (IoT)
• Constant Charge Current
• Handheld consumer devices
• Constant Charge Voltage
• Wearable market
• Pre-charge
• PoS terminals
• Trickle
• Medical portable equipment
• Consumer tablets
BC3770
Application
USB
Battery
Charger
MCU
8
Battery
Analog, Mixed-Signal, and Power Management
Applications
RADAR SYSTEMS
77 GHz radar systems support adaptive cruise control, pre-crash protection and collision warning systems with and without automatic
steering and braking intervention. In a collision warning system, the radar chipset can detect and track objects, automatically adjusting the
vehicle’s speed and distance in response to the traffic ahead and triggering a driver warning of an imminent collision and initiate emergency
braking intervention.
TYPICAL APPLICATIONS:
Automotive
Industrial
• Adaptive Cruise Control
(ACC)
• Robotics
• Blind-spot Detection (BSD)
• Industrial Automation
precision monitor
• Emergency Braking
• Industrial Surveillance
and Security Systems
• Forward Collision Warning
(FCW)
• Millimeter Wave Backhaul
Systems
• Headway Alert
• Mitigation and Brake
Support
• Pre-crash Detection
• Industrial Safety
• Precision Distance
Measurement Systems
• Rear Collision Protection
(RCP)
• Stop & Go
MR2001RVK
Receiver
CONSIDER:
• Qorivva 32-bit
MPC577xK
MCU
MR2001TVK
Voltage Controlled
Oscillator
Transmitter
MR2001VVK
XTAL
9
Applications
Analog, Mixed-Signal, and Power Management
POWER MANAGEMENT GENERIC SYSTEM DIAGRAM
Embedded power regulation is the function of converting system input power to the voltages and currents required by the MCU or DSP as
well as DDR (Double Data Rate) memory.
TYPICAL
APPLICATIONS:
LOOP CONTROL
SCHEMA:
POWER CONTROL
SCHEMA:
• Industrial Controls
• Voltage Mode
Feedback
• Linear Regulators
• Current Mode
Feedback
• Battery Management
• Embedded Control
Modules
• Consumer
Appliances
• Switching Regulators
• Marine Electronics
• Engine/Generator
Control
• Network Equipment
• Set-Top Box
• Battery Chargers
• Travel Chargers
INPUT
FILTERING
INTER-MODULE
COMMUNICATION
CONSIDER:
• S08
• S12
• i.MX6/7
10
NETWORK
TRANCEIVERS
33730
33742
33889
33903/34903
33904/34904
POWER
MANAGEMENT
(POWER
CONVERSION
and
REGULATION)
33905/34905
33910
33911
33912
VDD1
VDD2
VDDn
PARALLEL I/O
SPI I/O
33399
33660
33661
33662
33663
33897
33901/34901
CM0902
33989
34713
34716
34717
VR500
PF0100
PF0200
PF3000
SPI I/O
MCU
or
DSP
Analog, Mixed-Signal, and Power Management
Applications
BATTERY MANAGEMENT GENERIC SYSTEM DIAGRAM
For lead acid batteries, an intelligent sensor combines the requirements of accurate measurement sensing with logic capability to bring
decision making to the sensing solution.
TYPICAL APPLICATIONS:
For mission critical battery operations:
Automotive
LOOP CONTROL
SCHEMA:
POWER CONTROL
SCHEMA:
• Voltage
• Linear Regulators
• Temperature Current
• 12 V Lead Acid, 14V Li-Ion
• HV Battery Junction Box
• Multi-Battery Applications
Trucks and Utilities
• 24 V Lead Acid
Industrial
BATTERY TYPES:
• Energy Storage Systems (ESS)
• UPS
• 12 V Lead Acid Battery
• Industrial Automation precision
monitor
• 14 V Li-Ion Battery
• Lead Acid Multi-battery
• eBike
• Power tools Network Equipment
• Set-Top Box
• Battery Chargers
• Travel Chargers
High-voltage Battery Cells Control
33903
33905
33907
33908
FS6407
FS6408
FS4409
Li-Ion Cells Supervising Circuitry
912_637
9Z1_638
12 V Battery Sensor
CONSIDER:
Battery Junction Box
• S12G
• MPC5748G
• MPC56xB
Comm. and
Isolation
MCU
SBC
33903
33905
33907
33908
FS6407
FS6408
FS4409
High-voltage
Battery Multi-Cells
Li-Ion
SBC
MCU
Pumps, Heater,
Sensors
12 V Battery
Signal Inputs
3-Phase Driver
Temperature
Switches
MCU
33937
SBC
High-voltage Battery
Thermal Control
33903
33905
33907
33908
33909
FS6407
FS6408
FS4409
11
Applications
Analog, Mixed-Signal, and Power Management
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR
Freescale
Part Number
12XS2
Description
12 V Multipurpose Low RDS(on) eXtreme Switch
Product
12XS3
12
# of outputs
RDS(on)
(mOhm)
MC33981
Single
MC33982
Single
1 X 2.0
MC33984
Dual
2 X 4.0
MC33988
1 X 4.0
Dual
2 X 8.0
12 V Automotive Exterior Lighting Multichannel
eXtreme Switch
Product
12XS6
Main Characteristics
# of outputs
RDS(on)
(mOhm)
MC06XS3517
Penta
3 X 6.0
2 X 17.0
MC07XS3200
Dual
2 X 7.0
MC09XS3400
Quad
4 X 9.0
MC10XS3412
Quad
2 X 10.0
2 X 12.0
MC10XS3425
Quad
2 X 10.0
2 X 25.0
MC10XS3435
Quad
2 X 10.0
2 X 35.0
MC10XS3535
Penta
3 X 10.0
2 X 35.0
MC15XS3400
Quad
4 X 15.0
MC35XS3400
Quad
4 X 35.0
MC35XS3500
Penta
5 X 35.0
The eXtreme switch MC12XS2 family consists of very low RDS(on) devices in single
or dual high-side configuration to replace electromechanical relays or discrete
devices, in power management applications and DC motor control. The devices
are designed for harsh environments, and it includes self-recovery features. The
devices are suitable for loads with high inrush current, as well as motors and all
types of resistive and inductive loads.
The eXtreme Switch Gen3 12 V devices are SPI-Controlled smart high-side
switches providing diagnostics for the switch, light source and wiring harness, as
well as comprehensive fault management and control of the loads without complex
software. The devices use a programmable multi-step latched overcurrent
shutdown protection.
External Automotive Lighting Multichannel Scalable The Gen4 eXtreme Switch is the latest achievement in automotive lighting drivers.
eXtreme Switch
It belongs to an expanding family to control and diagnose bulbs and also the light
emitting diodes (LEDs) with enhanced diagnostic precision. It combines flexibility
RDS(on)
through daisy chainable SPI at 5.0 MHz, extended digital and analog feedbacks,
Product
# of outputs
(mOhm)
safety and robustness. Its low RDS(on) and high integration allows power and space
saving at the module level. It is also compliant with an Asil-B module design. This
MC07XS6517
Penta
3 X 7.0
family is packaged in a Pb-Free power-enhanced SOIC package with exposed
2 X 17.0
pad, which is ELV compliant.
MC08XS6421
Quad
2 X 8.0
2 X 21.0
MC10XS6200
Dual
2 X 10.0
MC10XS6225
Dual
1 X 10.0
1 X 25.0
MC10XS6325
Triple
2 X 10.0
1 X 25.0
MC17XS6400
Quad
4 X 17.0
MC17XS6500
Penta
5 X 17.0
MC25XS6300
Triple
3 X 25.0
MC40XS6500
Penta
5 X 40.0
Analog, Mixed-Signal, and Power Management
Applications
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
24XS4
Description
24 V Multipurpose Low RDS(on) Intelligent eXtreme
Switch
Product
12XSB
# of outputs
Dual
2 X 6.0
MC10XS4200
Dual
2 X 10.0
MC20XS4200
Dual
2 X 20.0
MC22XS4200
Dual
2 X 22.0
MC50XS4200
Dual
2 X 50.0
12 V Industrial Multipurpose Low RDS(on) eXtreme
Switch
# of outputs
RDS(on)
(mOhm)
MC34981
Single
1 X 4.0
MC34982
Single
1 X 2.0
MC34984
Dual
2 X 4.0
MC34988
Dual
2 X 8.0
12 V External Industrial Lighting Multichannel
eXtreme Switch
Product
# of outputs
These devices are part of a 24 V high-side switch product family with integrated
control, and a high number of protective and diagnostic functions. It is designed for
truck, bus, and 24 V based transportation systems. The low RDS(on) channels can
control different load types; lamps, solenoids, or DC motors. Control, device
configuration, and diagnostics are performed through a 16-bit serial peripheral
interface (SPI), allowing easy integration into existing applications.
RDS(on)
(mOhm)
MC06XS4200
Product
12XSC
Main Characteristics
RDS(on)
(mOhm)
MC06XSC517
Penta
3 X 6.0
2 X 17.0
MC07XSC200
Dual
2 X 7.0
MC09XSC400
Quad
4 X 9.0
MC10XSC412
Quad
2 X 10.0
2 X 12.0
MC10XSC425
Quad
2 X 10.0
2 X 25.0
MC10XSC435
Quad
2 X 10.0
2 X 35.0
MC10XSC535
Penta
3 X 10.0
2 X 35.0
MC15XSC400
Quad
4 X 15.0
MC35XSC400
Quad
4 X 35.0
MC35XSC500
Penta
5 X 35.0
The 12 V eXtreme Switch family consists of very low RDS(on) devices in single
high-side configuration, to replace electromechanical relays or discrete devices in
industrial power management applications and DC motor control. The devices are
designed for harsh environments, and include self-recovery features. The devices
are suitable for loads with high inrush current, as well as motors and all types of
resistive and inductive loads.
The eXtreme switch devices are SPI-controlled smart high-side switches for
Industrial applications, providing diagnostics, as well as comprehensive fault
management and control of the loads without complex software. The devices use a
programmable multi-step latched overcurrent shutdown protection. This technique
is preferable to the current limit method because it minimizes the thermal stress
within the device during an overload condition, greatly reducing the junction
temperature rise and vastly improving reliability.
13
Applications
Analog, Mixed-Signal, and Power Management
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
12XSF
Description
External Industrial Lighting Multichannel Scalable
eXtreme Switch
Product
36XSD
# of outputs
RDS(on)
(mOhm)
MC07XSF517
Penta
3 X 7.0
2 X 17.0
MC08XSF421
Quad
2 X 8.0
2 X 21.0
MC10XSF200
Dual
2 X 10.0
MC10XSF225
Dual
1 X 10.0
1 X 25.0
MC10XSF325
Triple
2 X 10.0
1 X 25.0
MC17XSF400
Quad
4 X 17.0
MC17XSF500
Penta
5 X 17.0
MC25XSF300
Triple
3 X 25.0
MC40XSF500
Penta
5 X 40.0
36 V Multipurpose Industrial Low RDS(on) Intelligent
eXtreme Switch
Product
14
Main Characteristics
# of outputs
RDS(on)
(mOhm)
MC06XSD200
Dual
2 X 6.0
MC10XSD200
Dual
2 X 10.0
MC16XSD200
Dual
2 X 16.0
MC22XSD200
Dual
2 X 22.0
MC50XSD200
Dual
2 X 50.0
The eXtreme switch products are the latest achievement in DC motors and
industrial lighting drivers. They belong to an expanding family to control and
diagnose various types of loads, such as incandescent bulbs or light emitting
diodes (LEDs), with enhanced precision. The products combine flexibility through
daisy chainable SPI at 5.0 MHz, extended digital and analog feedbacks, which
supports safety and robustness. This new generation of Freescale's high-side
switch products family facilitates electronic control unit designs supported by the
use of compatible MCU software and PCB footprints, for each device variant.
Freescale's family of intelligent, dual high-side eXtreme switches for 36 V systems
offers devices with current capability ranging from one to 12 A DC that are fully
compatible in footprint and software within the PQFN sub family. Each output can
be programmed to be used for any kind of loads, including lamps, LEDs, motors or
solenoids. This allows customers to design a flexible module which can become
specific and optimized for a given application through software. Freescale's 36 V
eXtreme switch solution provides robust design, intelligence and safety needed for
industrial applications up to 36 V supply voltage.
33399
Local Interconnect Network (LIN) Physical Interface LIN Transceiver with Wake and Enable Inputs, Inhibit Output
33660
ISO K Line Serial Link Interface
A serial link bus interface device designed to provide bi-directional half-duplex
communication interfacing in automotive diagnostic applications. It is designed to
meet the automotive diagnostic systems ISO9141 specification.
33661
Enhanced LIN Transceiver
Selectable Slew Rate for Operations at 10, 20, and 100 kbps; Bus Short to Ground
Fail-safe; Excellent EMC Behavior
33662
LIN 2.1 / SAEJ2602-2, LIN Physical Layer
Transceiver
The 33662s are physical Layer components dedicated to automotive LIN sub-bus
applications. They features either a 20 kbps baud rate or a 10 kbps baud rate. The
33662s integrate fast baud rate for test and programming modes, and provide
excellent ESD robustness, immunity against disturbance, and radiated emission
performance.
33663
LIN 2.1 / SAEJ2602-2 Dual LIN Physical Layer
The 33663 product line integrates two physical layer LIN bus dedicated to
automotive LIN sub-bus applications. The MC33663LEF and MC33663SEF
devices offer normal baud rate (20 kbps) and the MC33663JEF slow baud rate (10
kbps). Both devices integrate fast baud rate (above 100 kbps) for test and
programming modes.
33664
Isolated Network High-speed Transceiver Physical
Layer (TPL)
The 33664TL is a transceiver physical layer transformer driver designed to
conveniently interface a microcontroller to a high-speed isolated communication
network.
Analog, Mixed-Signal, and Power Management
Applications
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
Description
Main Characteristics
33730
Switch Mode Power Supply with Multiple Linear
Regulators
The 33730 is a multiple output power supply integrated circuit for automotive
applications. The integrated circuit (IC) incorporates a switching regulator which
operates over a wide input voltage range from +4.5 V to +26.5 V.
The step-down switching regulator uses a fixed frequency PWM voltage mode
control. It has a 3.5 A current limit (typical) and the slew-rate is adjustable via a
control pin to reduce switching noise. The linear regulators can be configured
either as two normal mode regulators (VDD3, VDDL) and one standby regulator
(VKAM), or as one normal mode linear regulator (VDDL) and two standby
regulators (VKAM and VDD3 Standby).
33742
System Basis Chip with Enhanced High-speed
CAN Transceiver
SBC, Dual VREG, Enhance HS CAN with Bus Failure Diagnostic Capability, 4
Wake-up Inputs
33771
Battery Cell Controller IC (BCC)
The 33771 is a lithium ion Battery Cell Controller IC designed for automotive
applications, such as hybrid electric (HEV) and electric vehicle (EV) systems as
well as industrial applications, such as energy storage systems (ESS) and
uninterruptible power supply (UPS) systems.
33780
Dual DBUS Master with Differential Drive and
Frequency Spreading
The 33780 is a master device for two differential DBUS buses. It contains the logic
to interface the buses to a standard serial peripheral interface (SPI) port and the
analog circuitry to drive data and power over the bus as well as receive data from
the remote slave devices.
33781
Quad DBUS Master with Differential Drive and
Frequency Spreading
The 33781 is a master device for four differential DBUS buses. It contains the logic
to interface the buses to a standard serial peripheral interface (SPI) port and the
analog circuitry to drive data and power over the bus as well as receive data from
the remote slave devices.
33784
Distributed System Interface (DSI) Sensor Interface 2-Channel, 10-Bit A-to-D, 5.0 V Regulated Output, DSI Bus, 3 Configurable I/O,
Fault Tolerant, High Drive Output
33789
Airbag System Basis Chip (SBC) with Power
Supply and PSI5 Sensor Interface
The 33789 offers an industry standard serial peripheral interface (SPI) and four
PSI5 master interfaces. The 33789 has a dedicated safing state machine that
complements an airbag’s MCU hardware/ software safing approach. Also included
are a diagnostic - self protection capability.
33790
Two-Channel Distributed System Interface (DSI)
Physical Interface Device
The 33790 is a dual channel physical layer interface IC for the Distributed System
Interface (DSI) bus. It is designed to meet automotive requirements. It can also be
used in non automotive applications. It supports bidirectional communication
between slave and master ICs. Some slave devices derive a regulated 5.0 V from
the bus, which can be used to power sensors, thereby eliminating the need for
additional circuitry and wiring.
33793
Distributed System Interface (DSI) Share Interface
Sensor
4-Channel, 8-Bit A-to-D, 5.0 V Regulated Output, DSI Bus, Configurable
I/O, Fault Tolerant
33800
Engine Control Integrated Circuit (IC)
16 Channel low-side and gate driver IC. Provides 8 low-side switches, 2 constant
current low-side switches, and 6 external MOSFET gate drivers.
33810
Eight Channel Ignition and Injector Driver
8 Channel load driver. Comprised of 4 low-side output drivers and 4 external
MOSFET, or IGBT gate drivers
33811
Solenoid Monitor Integrated Circuit (IC)
A 5 Channel solenoid monitor IC. Provides verification of solenoid operation by
monitoring the solenoid current waveform.
33812
Multifunction Ignition and Injector Driver
Three low-side drivers, one pre-driver, a +5.0 V voltage pre-regulator, an MCU
watchdog circuit and a ISO 9141 K-Line interface, for single/ dual cylinder engine
control.
Programmable Solenoid Controller
The PT2000 is a SMARTMOS programmable gate driver IC for precision solenoid
control applications, which makes the component very flexible and relieves the
main microcontroller from the heavy task of the actuator control.
33879
Configurable Octal Serial Switch with Open Load
Detect Current Disable
An 8-output hardware-configurable, high-side/low-side switch, with a 16-bit serial
(SPI) input control. 0.75 Ohm RDS(on)
33880
Configurable Eight Output Control Switch with SPI
(0.55 Ohm RDS(on))
8-output hardware configurable high-side/low-side switch with 8-bit serial input
control
33882
Output Switch with SPI and Parallel Input Control
(0.3 Ohm RDS(on)). Contains 6 Low-side Switches.
Fully protected, 6 x 1.0 a (SPI and parallel control) + 2 x 30 ma (parallel control)
switches, and SPI diagnostics
33886
H-Bridge Driver (5.0 A H-Bridge)
Monolithic H-Bridge ideal for fractional horsepower DC motor and bidirectional
thrust solenoid control
PT2000
15
Applications
Analog, Mixed-Signal, and Power Management
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
Description
Main Characteristics
33887
H-Bridge with Load Current Feedback
(5.0 A H-Bridge)
Supports forward, reverse, freewheeling, 10 kHz PWM, status, disable inputs, and
load current feedback
33889
System Basis Chip with Low Speed Fault Tolerant
CAN
2x regulator, high-side switched power, LS CAN, SPI, wake-up inputs, window
watchdog, reset, and interrupt
33897
Single Wire CAN Transceiver
Carrier sense multiple access/collision resolution (CSMA/CR) data link, and bus
activity sleep/wake-up
33899
Programmable H-Bridge Power Integrated Circuit
(IC)
Programmable H-Bridge controller for a DC motor or two solenoids. Parallel inputs
as well as a SPI interface provided control and diagnostic reporting, including
PWM’ed outputs.
Dual CAN High-Speed Transceiver
The CM0902 Dual CAN High-speed physical layer is Freescale's cost-effective
product designed to target standard CAN High-speed applications requiring
multiple transceivers.
High-Speed CAN Transceiver
The 33/34901 is the latest standard cost-effective product designed to target CAN
FD (flexible data) operation up to 2 Mbps and used to convert digital protocol
information into analog CAN communication. The device supports long-length
CAN node interconnects for industrial applications.
System Basis Chip Gen2 with High-Speed CAN
and LIN Interface
The 33/34903 is the second generation family of System Basis Chips which
combine several features and enhance present module designs. The device works
as an advanced power management unit for the MCU and additional integrated
circuits such as sensors, CAN transceivers. It has a built-in enhanced high-speed
CAN interface (ISO11898-2 and -5), and may include zero, one or two LIN 2.0
interfaces
System Basis Chip Gen2 with High-speed CAN
The 33/34904 is the second generation family of System Basis Chips which
combine several features and enhance present module designs. The device works
as an advanced power management unit for the MCU and additional integrated
circuits such as sensors, CAN transceivers. It has a built-in enhanced high-speed
CAN interface (ISO11898-2 and -5).
System Basis Chip Gen2 with High-speed CAN
and LIN Interface
The 33/34905 is the second generation family of System Basis Chips which
combine several features and enhance present module designs. The device works
as an advanced power management unit for the MCU and additional integrated
circuits such as sensors, CAN transceivers. It has a built-in enhanced high-speed
CAN interface (ISO11898-2 and -5), and may include one or two LIN 2.0
interfaces.
System Basis Chip (SBC) with LIN Transceiver Low End
SBC device combines a 5.0 V, 60 mA LDO, LIN transceiver, a high-side switch
output, one analog/logic input and a watchdog timer, with SPI and PWM control
System Basis Chip (SBC) with LIN Transceiver Medium End
SBC device combines a 5.0 V, 60 mA LDO, LIN transceiver, one high-side switch
output, two low-side switch outputs, two analog/logic inputs and a watchdog timer,
with SPI and PWM control.
System Basis Chip (SBC) with LIN Transceiver High End
SBC device combines a 5.0 V, 60 mA LDO, a switched 5.0 V output, LIN
transceiver, two high-side switch outputs, two low-side switch outputs, four analog/
logic inputs and a watchdog timer, with SPI and PWM control.
33926
5.0 A throttle Control H-Bridge Power Integrated
Circuit (IC)
This device drives a DC motor or 2 solenoids for actuator control. Parallel input
control of outputs and fault reporting.
33931
5.0 A Throttle Control H-Bridge
The 33/34931 is a monolithic H-Bridge power IC in a robust thermally enhanced
package. It is designed for automotive electronic throttle control, but is applicable
to any industrial low-voltage DC servo motor control application.
5.0 A Throttle Control H-Bridge (Dual)
The 33/34932 is a monolithic H-Bridge power IC in a robust thermally enhanced
package. The 33/34932 has two independent monolithic H-Bridge Power ICs in the
same package. They are designed for automotive electronic throttle control, but is
applicable to any industrial low-voltage DC servo motor control application.
Three Phase Field Effect Transistor Pre-driver
The 33/34937 is a field effect transistor (FET) pre-driver designed for three phase
motor control and similar applications. The IC contains three high-side FET predrivers and three low-side FET pre-drivers.Three external bootstrap capacitors
provide gate charge to the high-side FETs.
33CM0902
34CM0902
33901
34901
33903
34903
33904
34904
33905
34905
33910
34910
33911
34911
33912
34912
34931
33932
34932
33937
34937
16
Analog, Mixed-Signal, and Power Management
Applications
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
33972
Description
Main Characteristics
Multiple Switch Detection Interface with
Suppressed
Wake-up
Multiple switch detection interface with suppressed wake-up designed to detect
closing and opening of up to 22-switch contacts.
Multiple Switch Detection Interface with
Suppressed
Wake-up and 32 mA Wetting Current
22 inputs contact monitoring (14 GND, 8 configurable), and selectable wake-up on
change of state.
Configurable IO - Multiple Switch Detection
Interface
The MC33978/MC34978 configurable I/O is an analog switch interface used to
translate22 I/Os onto a single MCU SPI bus, with low power auto-wake modes and
programmable wetting currents.
33989
System Basis Chip with High-speed CAN
2x regulator, high-side switched power, SPI, wake-up inputs, window watchdog,
interrupt, and CAN transceiver
33996
16 Output Switch with SPI Control. (0.55 Ohm
RDS(on))
A 16-output low-side switch with a 24-bit serial input control (SPI), for control and
diagnostics. Ouputs are current limited (0.9 to2.5 A). Output voltage clamp of
+50 V during inductive switching. selectable PWM control of outputs. Protection
circuits
33999
16 Output Switch with SPI and PWM Control
(0.55 Ohm RDS(on))
A 16-output low-side switch with a 24-bit serial control (SPI) The SPI provides both
input control and diagnostic readout. Eight parallel inputs also provide direct pulse
width modulation (PWM) control of eight dedicated outputs. Reset input.
77 GHz Radar Transceiver Chipset
The MR2001 is a high-performance 77 GHz radar transceiver chipset scalable for
multi-channel operation enabling a single radar platform with electronic beam
steering and wide field of view to support long-range radar (LRR), mid-range radar
(MRR) and short-range radar (SRR) applications.
34671
600 mA High Input Voltage Charger for Single-cell
Li-Ion and Li-Polymer Batteries
The MC34671 is a cost-effective fully integrated battery charger for Li-Ion or LiPolymer batteries. It tolerates an input voltage up to 28 V, which eliminates the
input over-voltage protection circuit required in handheld devices. A charge cycle
includes trickle, constant-current (CC) and constant-voltage (CV) charge modes.
34673
1.2 A High Input Voltage Charger for Single Cell Li- The MC34673 is a cost-effective fully-integrated battery charger for Li-Ion or LiIon and Li-Polymer Batteries
Polymer batteries. It tolerates an input voltage up to 28 V, which eliminates the
input over-voltage protection circuit required in handheld devices. A charge cycle
includes trickle, constant-current (CC) and constant-voltage (CV) charge modes.
34674
High Input Voltage Travel Charger for Single Cell
Li-Ion and Li-Polymer Batteries
The MC34674 is a fully integrated single-cell Li-Ion and Li-Polymer battery charger
optimized for travel charger applications. The few external components required
include a dual color LED for charge status indication, a negative temperature
coefficient (NTC) thermistor circuit for setting the charge temperature window, and
two decoupling capacitors. The MC34674 tolerates an input voltage up to 28 V,
which allows low cost AC/DC converters to be used for further system cost
reduction. A charge cycle of the MC34674 includes trickle, constant current (CC)
and constant voltage (CV) charge modes. The CC-mode current is selectable from
50 mA to 1.05 A, with 10% accuracy and the constant-output voltage in the CVmode is fixed at 4.2 V.
BC3770
2.0 A Switch-Mode Li-ion/Li-polymer Battery
Charger
The BC3770 is a fully programmable switching charger with dual-path output for
single-cell Li-Ion and Li-Polymer battery. This dual-path output allows mobile
applications with a fully discharged battery to boot up the system.
34676
Dual 28 V Input Voltage Charger with Linear
Regulator
The 34676 is a dual 28 V input voltage and fully-integrated single cell Li-Ion battery
charger targeting smart handheld applications. One of the inputs is optimized for
charging with a USB port and the second is optimized for an AC/DC adapter power
source. The charger has two 28 V power devices to eliminate the needs of any
external power-source selection and input over-voltage-protection circuitry. Each of
the power devices independently controls the charge current from the input and
behaves as an independent charger. Only one of the two chargers operates at a
time. The AC charger current and the USB charger current are programmable up
to 1.2 A and 400 mA with an external resistor respectively.
34700
9-18 V Four Output, Multi-Purpose Switching
Power Supply
The 34700 is a compact, high efficiency power supply, with on-chip power
MOSFETs that feature three step down switching regulators and one low dropout
linear regulator. The switching regulators utilize voltage mode control with external
compensation, allowing flexibility in optimizing the performance of the 34700 for a
given application.
34972
33975
34975
33978
34978
MR2001
17
Applications
Analog, Mixed-Signal, and Power Management
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
Description
34704
Multi-channel Power Management IC (PMIC)
The 34704 is a multi-channel power management IC (PMIC) used to address
power management needs for various multimedia application microprocessors. Its
ability to provide either 5 or 8 independent output voltages with a single input
power supply (2.7 and 5.5 V) together with its high efficiency, make it ideal for
portable devices powered up by Li-Ion/polymer batteries or for USB powered
devices as well.
34708
Power Management Integrated Circuit (PMIC) for
the i.MX50/53 Families
The 34708 is the PMIC designed specifically for use with the Freescale i.MX50 and
i.MX53 processor families. As the companion PMIC on several i.MX reference
designs, it is a proven solution, which enables a faster time to market with fewer
resources.
34709
Power Management Integrated Circuit (PMIC) for
i.MX50/53 Families
The 34709 is the Power Management Integrated Circuit (PMIC) designed primarily
for use with the Freescale i.MX50 and i.MX53 families. It offers a low cost solution
targeting embedded applications that do not require a battery charger.
34VR500
Power Management Integrated Circuit for QorlQ
LS1 networking communications processors
The 34VR500 is a high performance, highly integrated, multi-output, SMARTMOS,
DC/DC regulator solution, with integrated power MOSFETs ideally suited for the
LS1 family of communication processors.
PF0100
14 Channel Configurable Power Management
Integrated Circuit
The PF0100 Power Management Integrated Circuit (PMIC) provides a highly
programmable/ configurable architecture, with fully integrated power devices and
minimal external components. With up to six buck converters, six linear regulators,
RTC supply, and coin-cell charger, the PF0100 can provide power for a complete
system, including applications processors, memory, and system peripherals, in a
wide range of applications.
PF0200
12 Channel Configurable Power Management
Integrated Circuit
The PF0200 Power Management Integrated Circuit (PMIC) provides a highly
programmable/ configurable architecture, with fully integrated power devices and
minimal external components. With up to four buck converters, one boost
regulator, six linear regulators, RTC supply, and coin-cell charger, the PF0200 can
provide power for a complete system, including applications processors, memory,
and system peripherals, in a wide range of applications.
PF3000
Power Management Integrated Circuit (PMIC) for
i.MX 7 & i.MX 6 DL/SL/SX
The PF3000 is a Power Management Integrated Circuit (PMIC) designed
specifically for use with the Freescale i.MX 7 and i.MX 6 DL/SL/SX application
processors.
34713
Single Synchronous Buck Switching Regulator
(5.0 A)
Synchronous buck switching regulator with adjustable output and an
accuracy of ±2% and a programmable switch frequency of 200 KHz to 1.0 MHz.
34716
Dual Synchronous Buck Switching Regulators
(5.0 A, +/-3.0 A)
Synchronous buck switching regulators with adjustable outputs and
an accuracy of ±2% and a programmable switch frequency of 200 KHz to 1.0 MHz.
34717
Dual Synchronous Buck Switching Regulators
(5.0 A, 5.0 A)
Synchronous buck switching regulators with adjustable outputs and an accuracy of
±2% and a programmable switch frequency of 200 KHz to 1.0 MHz.
34844
10 Channel LED Backlight Driver with Integrated
Power Supply
The 34844 is a high efficiency, LED driver for use in backlighting LCD displays
from 10" to 20"+. Operating from supplies of 7.0 to 28 V, the 34844 is capable of
driving up to 160 LEDs in 10 parallel strings.
FS6407
Safe System Basis Chip with Buck and Boost DC/
DC up to 800 mA
Multiple switching and linear voltage regulators, built-in enhanced high-speed CAN
interface fulfills the ISO11898-2 and -5 standards.
FS6408
Safe System Basis Chip with Buck and Boost DC/
DC up to 1.5 A
Multiple switching and linear voltage regulators, built-in enhanced high-speed CAN
interface fulfills the ISO11898-2 and -5 standards.
33909
System Basis Chip with Multiple Switch-to-Ground
Interface
The 33909/34FS4409 integrates the common functionality of system basis chips
with switch detection inputs. The device works as an advanced power
management unit for the MCU and additional integrated circuits such as sensors,
CAN transceivers, and eXtreme switches.
1.4 A Dual H-Bridge Driver Compatible with 3.0 V
Logic
The 34933 is a two channel H-Bridge driver aimed at the digital camera market.
There are a variety of applications containing bipolar step motors and/or brush DC
motors, such as Auto Focus control for the digital camera lens. The 34933 uses
Freescale's proprietary SMOS8 Bi CMOS process to deliver a low power device,
with a maximum quiescent current of 100 µA for the motor drive supply and 400 µA
for the Control Logic supply.
FS4409
34933
18
Main Characteristics
Analog, Mixed-Signal, and Power Management
Applications
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
Description
Main Characteristics
908E621
Integrated Quad Half-bridge and Triple High-side
with Embedded MCU and LIN for High End Mirror
A high performance HC08 microcontroller with a SMARTMOS analog control IC.
The analog control die provides four half-bridges and three high-side outputs with
diagnostic functions, a Hall Effect sensor input, analog inputs, voltage regulator,
window watchdog, and local interconnect network (LIN) physical layer.
908E622
Integrated Quad Half-bridge, Triple High-side and
EC Glass Driver with Embedded MCU and LIN for
High End Mirror
A high performance HC08 microcontroller with a SMARTMOS analog control IC.
The analog control die provides four half-bridge and three high-side outputs with
diagnostic functions, an EC glass driver circuit, a Hall Effect sensor input, analog
inputs, voltage regulator, window watchdog, and local interconnect network (LIN)
physical layer.
908E624
Integrated Triple High-side Switch with Embedded
MCU and LIN Serial Communication for Relay
Drivers
A high performance HC08 microcontroller with a SMARTMOS analog control IC.
The analog control die provides three high-side outputs with diagnostic functions,
voltage regulator, watchdog, current sense operational amplifier, and local
interconnect network (LIN) physical layer.
908E625
Integrated Quad Half H-Bridge with Power Supply,
Embedded MCU, and LIN Serial Communication
A high performance HC08 microcontroller with a SMARTMOS analog control IC.
The analog control die provides fully protected H-Bridge/high-side outputs, voltage
regulator, autonomous watchdog with cyclic wake-up, and local interconnect
network (LIN) physical layer.
908E626
Integrated Stepper Motor Driver with Embedded
MCU and LIN Serial Communication
The analog control die provides fully protected H-Bridge outputs, voltage regulator,
autonomous watchdog, and local interconnect network (LIN) physical layer.
912_634
Integrated S12 Based Relay Driver products with
LIN, with 32/ 48/ 64 kB Flash memory
The MM912_634 products are integrated single package solutions that integrate
an HCS12 microcontroller with a SMARTMOS analog control IC, which combine a
system base chip and application specific functions, including a Local Interconnect
Network (LIN) transceiver
912_637
Battery Sensor with LIN for 12 V Lead-acid
Batteries
The MM912_637 is an integrated single package solution that integrates an
HCS12 microcontroller, with a SMARTMOS analog control IC containing system
base chip and application specific functions, including a LIN transceiver
9Z1_638
Battery Sensor with CAN and LIN
The MM9Z1_638 enables precision measurement of key battery parameters in
automotive and other applications. The device integrates an S12Z microcontroller
and a SMARTMOS analog control IC into a single package solution.
912_P812
S12P MCU and Multifunctional Ignition and Injector The MM912_P812 is an engine control IC combining an MCU (S12P) and analog
Driver System In Package (SiP)
control die (MC33812) intended for motorcycle and other single/dual cylinders
small engine control applications.
912_S812
S12XS MCU and Multifunctional Ignition and
Injector Driver System In Package (SiP)
The MM912_S812 is an engine control IC combining an MCU (S12XS) and analog
control die (MC33812) intended for motorcycle and other single/dual cylinders
small engine control applications.
17510
0.45 Ohm (TYP) H-Bridge Motor Driver
The 17510 is a monolithic H-Bridge that is ideal in portable electronic applications
to control small brush DC motors such as digital still and single lens cameras.
17529
0.7 Ohm TYP Dual H-Bridge Motor Driver
The 17529 is a monolithic dual H-Bridge that is ideal in portable electronic
applications to control bipolar stepper motors and brush DC motors such as found
in camera lens shutters, optical disk drives and other head positioners.
17531
700 mA Dual H-Bridge Motor Driver with 3.0 V
Compatible Logic I/O
The 17531 is a monolithic dual H-Bridge driver IC with integrated charge pump and
protection.
17533
0.7 Ohm (TYP) Dual H-Bridge Motor Driver
The 17533 is a monolithic dual H-Bridge IC that is ideal in portable electronic
applications for controlling stepper or brush DC-motors for example, camera lens
shutters and optical disk drives.
0.4 Amp Dual H-Bridge Motor Driver IC
A dual-channel H-Bridge power IC is deal for portable electronic applications
containing bipolar stepper motors or brush DC motors, like those in cameras.
33HB2000
10 A H-Bridge, Programmable Brushed DC Motor
Driver
The 33HB2000 is a monolithic H-Bridge Power IC, enhanced with SPI
configurability and diagnostic capabilities.
33HB2001
10 A H-Bridge, Programmable Brushed DC Motor
Driver
The 33HB2001 is a monolithic H-Bridge Power IC, enhanced with SPI
configurability and diagnostic capabilities.
33GD3000
Three Phase Field Effect Transistor Pre-driver
The GD3000 is a field effect transistor (FET) pre-driver designed for three
phase motor control and similar applications.
17C724
34GD3000
19
Applications
Analog, Mixed-Signal, and Power Management
ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL
CONDITIONING, AND RADAR (continued)
Freescale
Part Number
20
Description
Main Characteristics
SB0400
Two-Wheel Antilock Braking (ABS) Controller for
Motorcycles
The MC33SB0400 motorcycle antilock brake (ABS) controller has two high current
low-side drivers for solenoid valves, two configurable wheel speed sense inputs for
active sensors, and high-side gate drivers for controlling two external N-channel
MOSFETs.
SB0401
One-Wheel Antilock Braking (ABS) for Motorcycles The MC33SB0401 motorcycle antilock brake (ABS) controller has four high current
low-side drivers for solenoid valves, two configurable wheel speed sense inputs for
handling active sensors, and high-side gate drivers for controlling two external Nchannel MOSFETs.
34SB0410
Quad Valve Controller System on Chip
The Quad Valve Controller system on a chip (SoC), with integrated pump driver,
consists of four regulated low-side drivers and a high-side driver to control a DC
motor.
34SB0800
Octal Valve Controller System on Chip
The Octal Valve Controller system on a chip (SoC), with integrated pump driver,
consists of four regulated low-side drivers and four digital low-side driver, plus a
high-side driver to control a DC motor.
Analog, Mixed-Signal, and Power Management
References
Topic
Applications
URL
BR1567
Analog ICs Integrated Solutions Technology Brochure
http://www.freescale.com/files/analog/doc/brochure/
BR1567.pdf
BR1568
Analog ICs Integrated Solutions Packaging Brochure
http://www.freescale.com/files/analog/doc/brochure/
BR1568.pdf
SG1002
Analog, Mixed Signal and Power Management - http://www.freescale.com/files/shared/doc/selector_guide/
SG1002.pdf
Selector Guide
SG187
Automotive - Selector Guide
http://www.freescale.com/files/microcontrollers/doc/
selector_guide/SG187.pdf
SG200
Analog and Power Management Industrial
Products - Selector Guide
http://www.freescale.com/files/shared/doc/selector_guide/
SG200.pdf
BRAUTOSOL
Automotive Solutions - Brochure
http://www.freescale.com/files/microcontrollers/doc/brochure/
BRAUTOSOL.pdf
MDAPPUSGDRM118
Medical Applications - User Guide
http://www.freescale.com/files/microcontrollers/doc/
user_guide/MDAPPUSGDRM118.pdf
21
Communicating
Controlling
Protecting
Learn More: For current information about Freescale products and documentation, please visit www.freescale.com.
Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS
is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective
owners.
© 2015 Freescale Semiconductor, Inc.
Document Number: BR1569, Rev. 15.0, 11/2015
Similar pages