8 6 7 4 5 3 2 ALUMINUM COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SSMA ADAPTABLE, .012 OR .015 DIAMETER CENTER CONTACT D • CONFIGURATION FOR INTERFACING TO PANEL JACK ADAPTER (SRI CONNECTOR GAGE PART NUMBER 13-150-1500-00, INSTALL AT 13 1 LB-IN) REV SRIFT502 DOCUMENT REVISIONS DATE CHANGE NO. CFG APPROVAL - INIT RLSE 2008-09-29 J. PETRI A DCN000638 4/22/2010 J. PETRI B DCN000844 6/10/2011 Jim Petri Digitally signed by Jim Petri DN: cn=Jim Petri, o=SRI Hermetics, ou, [email protected], c=US Date: 2011.06.15 10:04:56 -04'00' B • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS D • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS • INTEGRAL RF GROUNDING TAB FOR EXCELLENT PERFORMANCE OVER TEMPERATURE 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. NOMINAL IMPEDANCE: 50 OHMS 3. INTERFACE IN ACCORDANCE WITH MIL-STD-348, SSMA. 4. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15. DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (LOW LOSS, MATCHED SEAL). SHELL (WELD FLANGE): ALUMINUM ALLOY 4047 IN ACCORDANCE WITH AWS A5.8. RF GROUNDING SPRING: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B 194 (NICKEL/GOLD PLATE) C 5. FINISH: EXCEPT WELD FLANGE: NICKEL PLATE PER QQ-N-290, CLASS 2, .000100/.000250 THICK GOLD PLATE PER ASTM B488-01, TYPE III, CODE A, .000050/.000100 THICK. VIEWS FOR REFEREENCE ONLY C 6. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBERS INDICATING PIN DIAMETER, D AND PIN LENGTH, L: EXAMPLE: SRIFT502 - 015 - 045 - A A=GROUNDING SPRING FOR AIR DIELECTRIC T=GROUNDING SPRING FOR TEFLON DIELECTRIC .235 PIN LENGTH, L=.045 (.035 MIN) PIN DIAMETER, D=.015 (.012 OR .015) L .003 .262 MAX OVER KNURL BASE NUMBER D .001 PIN B C .001 B .001 THRU (AIR DIELECTRIC) AS REQUIRED (TEFLON DIELECTRIC) .243 .001 .230 .002 .2580 .0005 .100 .005 .230 .040 MIN UNPLATED B RF GROUNDING SPRING, SHIPPED UNINSTALLED PART NUMBER SRIFT501-GS1, D=.012, AIR DIELECTRIC PART NUMBER SRIFT501-GS2, D=.015, AIR DIELECTRIC PART NUMBER SRIFT501-GS4, D=.012, TEFLON DIELECTRIC PART NUMBER SRIFT501-GS5, D=.015, TEFLON DIELECTRIC SHELL AS REQUIRED O (TEFLON DIELECTRIC, OPTIONAL) UNPLATED .003 MAX BRK O PART NUMBER D B C SRIFT502 - 012 - XXX - A .012 .028 ------ SRIFT502 - 012 - XXX - T .012 ------ .039 SRIFT502 - 015 - XXX - A .015 .035 ------ SRIFT502 - 015 - XXX - T .015 ------ .049 UNLESS OTHERWISE SPECIFIED A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 125 RMS SURFACE FINISH RECOMMENDED HOLE DETAIL THIRD ANGLE PROJECTION SRI HERMETICS TITLE FEEDTHROUGH, THREADED SSMA, AC LBW SIZE DOCUMENT 7 6 5 4 3 SRIFT502 A SCALE FORM 300067 REV - (321) 254-4067 WWW.SRIHERMETICS.COM 3:1 2 CAGE CODE 3PJY7 SHEET 1 REV B 1 OF 1 A