BYM11-50 THRU BYM11-1000 RGL41A THRU RGL41M SURFACE MOUNT GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER * Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere FEATURES T E D DO-213AB P A T E N ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ For surface mount applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 450°C/5 seconds at terminals. Complete device submersible temperature of 260°C for 10 seconds in solder bath 2nd BAND MECHANICAL DATA 2nd band denotes voltage type Dimensions in inches and (millimeters) *Glass-plastic encapsulation is covered by Patent No. 3,996,602 and brazed-lead assembly to Patent No. 3,930,306 ® Case: JEDEC DO-213AB molded plastic over glass body Terminals: Plated terminals, solderable per MIL-STD-750, Method 2026 Polarity: Two bands indicate cathode end -1st band denotes device type and 2nd band denotes repetitive peak reverse voltage rating Mounting Position: Any Weight: 0.0046 ounce, 0.116 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS Fast switching time device: 1st band is Red Polarity color bands (2nd Band) BYM11 -50 BYM11 -100 BYM11 -200 BYM11 -400 BYM11 -600 BYM11 BYM11 -800 -1000 UNITS RGL 41A RGL 41B RGL 41D RGL 41G RGL 41J RGL 41K RGL 41M Gray Red Orange Yellow Green Blue Violet Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at TT=55°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps VF 1.3 Volts IR 5.0 50.0 µA IR(AV) 50.0 µA Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C Maximum full load reverse current, full cycle average at TA=55°C Maximum reverse recovery time (NOTE 1) trr Typical junction capacitance (NOTE 2) CJ 15.0 pF Maximum thermal resistance (NOTE 3) RΘJA RΘJT 75.0 30.0 °C/W TJ, TSTG -65 to +175 °C (NOTE 4) Operating junction and storage temperature range 150 NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient, 0.24 x 0.24” (6.0 x 6.0mm) copper pads to each terminal (4) Thermal resistance from junction to terminal, 0.24 x 0.24” (6.0 x 6.0mm) copper pads to each terminal 10/98 250 500 Volts ns RATINGS AND CHARACTERISTIC CURVES BYM11-50 THRU BYM11-1000 / RGL41A THRU RGL41M FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 1.25 RESISTIVE OR INDUCTIVE LOAD 1.0 0.75 0.5 0.25 0 25 50 75 100 125 150 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 25 20 15 10 0 175 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 1 TERMINAL TEMPERATURE, °C TJ=25°C 1 PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 TJ=100°C 1 0.1 TJ=25°C 0.01 0 20 60 40 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 100 CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 MOUNTED ON 0.20 x 0.27” (5 x 7mm) COPPER PAD AREAS 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 1 10 REVERSE VOLTAGE, VOLTS 100 10 100