REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) MERITEK FEATURES Smaller case sizes than RE series. Lower impedance at high frequency and high ripple current. Suitable for output of motherboard and switching power supplies. SPECIFICATIONS Item Characteristic Operating Temp Range - 55 ~ +105C Rated Working Voltage 6.3 ~ 50VDC Capacitance Tolerance (120Hz 20C) 20%(M) I 0.01CV or 3 (uA) Leakage Current I : Leakage Current (A) C : Rated Capacitance(F) V : Working Voltage (V) (20C) ＊Whichever is greater after 3 minutes Surge Voltage (20C) W.V. 6.3 10 16 25 35 50 S.V. 8 13 20 32 44 63 16 25 35 50 0.16 0.14 0.12 0.10 Dissipation Factor ( tan ) add 0.02 per 1000uF for more than 1000uF (120Hz 20C) W.V. 6.3 10 tan Low Temperature Stability 0.22 0.19 Impedance ratio at 120Hz Rated Voltage (V) 6.3~16 25~50 -25C / +20C 3 2 -55C / +20C 6 4 After hours application (D ≤8mm 1000hrs, D ≥10mm 2000hrs) of W.V. and +105C ripple current value , the capacitor shall meet the following limits. ( DC + ripple peak voltage rated working voltage ) Load Life Shelf Life Capacitance Change 20% of initial value. Dissipation Factor 200% of initial specified value Leakage Current initial specified value At +105C no voltage application after 1000 hours the capacitor shall meet the limits for load life characteristics. ( with voltage treatment ) PART NUMBER SYSTEM DIMENSIONS (mm) REW 10V 101 M TA 5x11 Meritek Series Rated Voltage Rated Capacitance Express in micro farad(uF), First two digits are significant figures, Third digit denotes number of zeros. ‘R’ denotes decimal point for values less than 10uF Tolerance M - 20% Package Code TA Tape & Ammo TR Tape & Reel Blank Case size – (D) Diameter x (L) Length in mm (Optional) D F d a 5 2.0 0.5 1.5 6.3 2.5 0.5 1.5 8 3.5 0.6 1.5 10 5.0 0.6 1.5 12.5 5.0 0.6 1.5 16 7.5 0.8 1.5 18 7.5 0.8 1.5 Rev. 7a REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) MERITEK RIPPLE CURRENT COEFFICIENTS Frequency(Hz) 60 W.V. 10~16V 0.45 25~35V 0.38 50V 0.36 120 0.60 0.50 0.46 400 1k Multiplier 0.83 0.94 0.75 0.90 0.70 0.88 10k 100k 0.98 0.97 0.94 1.00 1.00 1.00 CASE SIZE & MAX RIPPLE CURRENT V Cap. (uF) Item 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 6.3 IMP DxL 20°C -10°C 5x11 5x11 0.219 0.190 0.656 0.571 5x11 0.162 0.487 5x15 6.3x11 5x15 6.3x11 6.3x15 8x11.5 6.3x15 8x11.5 6.3x15 8x11.5 6.3x15 8x11.5 8x15 10x12.5 8x15 10x12.5 8x20 10x16 10x20 12.5x15 10x20 12.5x15 10x25 12.5x18 0.148 0.148 0.130 0.130 0.117 0.117 0.106 0.106 0.094 0.094 0.084 0.084 0.077 0.077 0.069 0.069 0.059 0.059 0.036 0.036 0.031 0.031 0.028 0.028 0.444 0.444 0.389 0.389 0.351 0.351 0.319 0.319 0.283 0.283 0.252 0.252 0.230 0.230 0.206 0.206 0.178 0.178 0.107 0.089 0.094 0.078 0.083 0.069 R.C. 250 270 300 380 380 420 420 520 530 570 580 620 630 680 700 860 900 950 990 1180 1210 1450 1390 1590 1520 1880 1770 Temperature(C) 65 75 85 95 105 Multiplier 2.12 1.92 1.69 1.50 1.00 Case size : DxL (mm) Max. impedance :Ω 100kHz Max. ripple current : mA(rms) 105C 100kHz 10 IMP DxL 20°C -10°C R.C. 5x11 5x11 5x11 5x15 6.3x11 5x15 6.3x11 5x15 6.3x11 6.3x15 8x11.5 6.3x15 8x11.5 6.3x15 8x11.5 6.3x15 8x11.5 8x15 10x12.5 8x15 10x12.5 8x20 10x16 10x20 12.5x15 10x25 12.5x18 10x25 12.5x18 10x28 16x15 0.312 0.266 0.218 0.189 0.189 0.161 0.161 0.147 0.147 0.129 0.129 0.116 0.116 0.106 0.106 0.094 0.094 0.083 0.083 0.076 0.076 0.068 0.068 0.059 0.059 0.035 0.035 0.031 0.031 0.027 0.027 0.937 0.798 0.653 0.568 0.568 0.484 0.484 0.442 0.442 0.387 0.387 0.349 0.349 0.317 0.317 0.281 0.281 0.250 0.250 0.228 0.228 0.204 0.204 0.177 0.148 0.106 0.089 0.094 0.078 0.082 0.068 230 250 280 360 350 400 390 440 430 550 560 600 610 660 670 720 730 900 950 990 1040 1240 1280 1540 1480 1830 1720 2000 1880 2250 1960 All blank voltage on sleeve marking is the same voltage as “” point to. Rev. 7a REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) CASE SIZE & MAX RIPPLE CURRENT V Cap. (uF) Item 2700 3300 3900 4700 5600 6800 8200 10000 Case size Max. impedance Max. ripple current 6.3 IMP MERITEK : DxL (mm) :Ω 100kHz : mA(rms) 105C 100kHz 10 IMP DxL 20°C -10°C R.C. DxL 20°C -10°C R.C. 10x28 16x15 12.5x20 16x15 12.5x25 18x15 12.5x30 16x20 12.5x35 16x25 12.5x40 18x20 16x31.5 18x25 16x35.5 18x31.5 0.025 0.025 0.023 0.023 0.022 0.022 0.021 0.021 0.020 0.020 0.019 0.019 0.018 0.018 0.017 0.017 0.075 0.063 0.058 0.058 0.055 0.055 0.053 0.053 0.050 0.050 0.047 0.047 0.045 0.045 0.043 0.043 2140 1870 2150 2010 2520 2190 2860 2520 3060 2900 3450 2850 3540 3260 3880 3740 12.5x20 16x15 12.5x25 18x15 12.5x30 16x20 12.5x35 16x25 12.5x40 18x20 16x31.5 18x25 16x35.5 18x31.5 0.025 0.025 0.023 0.023 0.022 0.022 0.021 0.021 0.020 0.020 0.019 0.019 0.018 0.018 0.062 0.062 0.057 0.057 0.055 0.055 0.053 0.053 0.049 0.049 0.047 0.047 0.044 0.044 2250 2100 2650 2300 3030 2670 3210 3050 3550 2940 3680 3390 4010 3870 18x35.5 0.017 0.042 4190 All blank voltage on sleeve marking is the same voltage as “” point to. V Cap. (uF) Item 47 56 68 82 100 120 150 180 220 270 330 390 470 16 IMP DxL 20°C 25 IMP -10°C 5x11 5x11 5x11 0.253 0.221 0.203 0.759 0.662 0.610 5x11 0.183 0.550 5x15 6.3x11 5x15 6.3x11 5x15 6.3x11 5x15 6.3x11 6.3x15 8x11.5 6.3x15 8x11.5 8x15 10x12.5 8x15 10x12.5 0.156 0.156 0.128 0.128 0.111 0.111 0.095 0.095 0.086 0.086 0.076 0.076 0.068 0.068 0.062 0.062 0.469 0.469 0.383 0.383 0.333 0.333 0.284 0.284 0.259 0.259 0.227 0.227 0.205 0.205 0.186 0.186 R.C. 190 210 230 250 320 320 360 350 390 390 430 430 550 550 600 610 750 790 820 860 DxL 20°C -10°C R.C. 5x11 5x11 5x11 5x15 6.3x11 5x15 6.3x11 5x15 6.3x11 6.3x15 8x11.5 6.3x15 8x11.5 6.3x15 8x11.5 8x15 10x12.5 8x15 10x12.5 8x20 10x16 8x20 10x16 0.283 0.253 0.220 0.203 0.203 0.183 0.183 0.156 0.156 0.128 0.128 0.111 0.111 0.095 0.095 0.086 0.086 0.076 0.076 0.068 0.068 0.062 0.062 0.085 0.758 0.661 0.609 0.609 0.549 0.549 0.468 0.468 0.383 0.383 0.333 0.333 0.284 0.284 0.259 0.259 0.227 0.227 0.205 0.205 0.186 0.186 220 240 270 340 330 370 370 410 400 510 520 560 570 620 630 790 830 870 910 1080 1100 1180 1210 Rev. 7a REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) CASE SIZE & MAX RIPPLE CURRENT V Cap. (uF) Item 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 16 IMP DxL 20°C -10°C R.C. 8x20 10x16 8x20 10x16 8x20 10x16 10x20 12.5x15 10x25 12.5x18 10x28 16x15 12.5x20 16x15 12.5x25 18x15 12.5x30 16x20 12.5x35 16x25 12.5x40 18x20 16x31.5 18x25 16x35.5 18x31.5 0.055 0.055 0.049 0.049 0.045 0.045 0.040 0.040 0.035 0.035 0.029 0.029 0.026 0.026 0.023 0.023 0.021 0.021 0.019 0.019 0.018 0.018 0.016 0.016 0.015 0.015 0.165 0.165 0.147 0.147 0.134 0.134 0.120 0.100 0.104 0.087 0.088 0.074 0.065 0.065 0.057 0.057 0.052 0.052 0.048 0.048 0.046 0.046 0.040 0.040 0.038 0.038 1020 1050 1120 1150 1230 1270 1540 1480 1870 1750 2100 1830 2140 2000 2500 2170 2890 2540 3130 2970 3500 2900 3560 3280 3880 3740 MERITEK Case size : DxL (mm) Max. impedance :Ω 100kHz Max. ripple current : mA(rms) 105C 100kHz 25 IMP DxL 20°C -10°C R.C. 8x20 10x16 10x20 12.5x15 10x25 12.5x18 10x28 16x15 12.5x20 16x15 12.5x25 18x15 12.5x30 16x20 12.5x35 16x25 12.5x40 18x20 16x31.5 18x25 16x35.5 18x31.5 0.055 0.055 0.049 0.049 0.045 0.045 0.040 0.040 0.035 0.035 0.029 0.029 0.026 0.026 0.023 0.023 0.021 0.021 0.019 0.019 0.018 0.018 0.165 0.165 0.147 0.122 0.134 0.112 0.120 0.100 0.104 0.087 0.074 0.074 0.065 0.065 0.057 0.057 0.052 0.052 0.047 0.047 0.046 0.046 1290 1320 1610 1550 1950 1830 2270 1980 2320 2170 2710 2480 3230 2840 3470 3290 3910 3240 4100 3770 4530 4360 18x35.5 0.016 0.040 4720 All blank voltage on sleeve marking is the same voltage as “” point to. V Cap. (uF) Item 0.47 1 2.2 3.3 4.7 6.8 10 15 18 22 27 33 35 IMP DxL 5x11 5x11 5x11 5x11 5x11 5x11 5x11 5x11 20°C 1.062 0.917 0.832 0.610 0.531 0.454 0.400 0.353 50 IMP -10°C 3.185 2.752 2.495 1.829 1.594 1.361 1.201 1.058 R.C. 75 90 110 130 150 160 180 200 DxL 20°C -10°C R.C. 5x11 5x11 5x11 5x11 5x11 5x11 5x11 5x11 5x11 5x11 5x11 5x11 3.006 2.825 1.511 1.259 1.061 0.916 0.831 0.609 0.531 0.453 0.400 0.353 9.017 8.476 4.533 3.777 3.182 2.749 2.493 1.828 1.593 1.360 1.200 1.058 27 40 60 70 85 100 130 150 170 190 210 230 Rev. 7a REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) CASE SIZE & MAX RIPPLE CURRENT V Cap. (uF) Item 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 35 IMP DxL 20°C -10°C R.C. 5x11 0.320 0.096 210 5x11 0.283 0.849 230 5x15 6.3x11 5x15 6.3x11 5x15 6.3x11 6.3x15 8x11.5 6.3x15 8x11.5 6.3x15 8x11.5 8x15 10x12.5 8x15 10x12.5 8x20 10x16 8x20 10x16 10x20 12.5x15 10x20 12.5x15 10x25 12.5x18 10x28 16x15 10x30 16x15 12.5x25 18x15 12.5x30 16x20 12.5x35 16x25 12.5x40 18x20 16x31.5 18x25 0.252 0.252 0.220 0.220 0.203 0.203 0.183 0.183 0.109 0.109 0.089 0.089 0.078 0.078 0.066 0.066 0.060 0.060 0.053 0.053 0.048 0.048 0.043 0.043 0.038 0.038 0.034 0.034 0.031 0.031 0.028 0.028 0.024 0.024 0.021 0.021 0.018 0.018 0.016 0.016 0.757 0.757 0.660 0.660 0.608 0.608 0.549 0.549 0.327 0.327 0.268 0.268 0.233 0.233 0.198 0.198 0.181 0.181 0.159 0.159 0.143 0.119 0.130 0.108 0.115 0.096 0.103 0.086 0.094 0.078 0.070 0.070 0.061 0.061 0.051 0.051 0.045 0.045 0.040 0.040 290 290 320 320 360 350 450 450 490 500 550 550 680 720 750 790 950 970 1050 1080 1290 1240 1420 1360 1710 1610 1990 1730 2250 1900 2480 2150 2940 2590 3160 3000 3690 3050 3810 3510 MERITEK Case size : DxL (mm) Max. impedance :Ω 100kHz Max. ripple current : mA(rms) 105C 100kHz 50 IMP DxL 20°C -10°C R.C. 5x15 6.3x11 5x15 6.3x11 5x15 6.3x11 6.3x15 8x11.5 6.3x15 8x11.5 8x15 10x12.5 8x15 10x12.5 8x20 10x16 8x20 10x16 8x20 10x16 10x20 12.5x15 10x25 12.5x18 10x25 12.5x18 12.5x20 16x15 12.5x25 18x15 12.5x30 16x20 12.5x35 16x25 12.5x40 18x20 16x31.5 18x25 16x35.5 18x31.5 0.320 0.320 0.283 0.283 0.252 0.252 0.220 0.220 0.203 0.203 0.183 0.183 0.109 0.109 0.089 0.089 0.078 0.078 0.066 0.066 0.060 0.060 0.053 0.053 0.048 0.048 0.043 0.043 0.038 0.038 0.034 0.034 0.031 0.031 0.028 0.028 0.024 0.024 0.021 0.021 0.959 0.959 0.849 0.849 0.757 0.757 0.660 0.660 0.608 0.608 0.548 0.548 0.327 0.327 0.268 0.268 0.233 0.233 0.198 0.198 0.181 0.151 0.159 0.132 0.143 0.119 0.108 0.108 0.096 0.096 0.086 0.086 0.078 0.078 0.070 0.070 0.061 0.061 0.051 0.051 290 280 310 310 340 340 430 430 470 480 590 620 650 680 820 840 900 920 1000 1020 1250 1200 1530 1430 1660 1560 1790 1680 2150 1870 2580 2260 2880 2730 3390 2800 3660 3370 4040 3890 All blank voltage on sleeve marking is the same voltage as “” point to. Rev. 7a REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) MERITEK TAPING SPECIFICATION Lead taping is designed for automatic insertion equipment. Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type. DIMENSIONS (Ø4~ Ø10) Item Symbol Case Size 4x5 5 x 5 6.3x5 8 x 5 4x7 5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16 0.45 0.5 10x18 10x20 Tolerance Lead wire diameter d Body height A Intervals of bodies P 12.7 ±1.0 Intervals of punched holes P0 12.7 ±0.2 6.0 8.0 12.5 13 14 0.6 ±0.05 17.5 19.5 21.5 MAX Fig 1. Fig 4. 3.85 Distance between holes and lead wire P1 5.35 5.1 5.1 5.6 Distance between holes and bodies 5.35 5.1 5.1 5.35 5.1 5.1 5.6 ±0.7 5.1 5.35 5.1 4.6 5.35 5.1 P2 F 6.35 2.0 2.5 2.5 2.0 2.5 2.5 Fig 2. Fig 3. 4.6 ±1.0 Fig 1. Fig 4. 5.0 Distance between lead and lead Remark +0.8 -0.2 2.5 Fig 2. F1:5.0 +0.5 Fig 3. F1:5.0 +0.5 -1.0 1.5 2.0 2.5 2.5 1.5 2.0 2.5 3.5 2.0 2.5 3.5 -1.0 Base tape width W 18.0 ±0.5 Adhesive tape width W0 12.5 MIN Deviation between holes and base tape W1 9.0 ±0.5 Deviation between adhesive and base tape W2 1.5 MAX 17.5 18.5 20.0 17.5 18.5 18.5 18.5 Distance between body bottom and tape center H Lead wire clinched height H0 Distance between body top and tape center H1 Punched hole diameter D0 4.0 ±0.3 Length of not good lead slit L 11.0 MAX Base and adhesive tape thickness t 0.6 ±0.3 Deviation of body alignment ∆h 0 ±2.0 Deviation of body alignment ∆h1 0 ±1.0 ±0.5 16.0 24.5 Fig 1. Fig 4. Fig 2. Fig 3. ±0.5 27.5 32.5 33.0 36.0 38.0 41.0 MAX Rev. 7a REW Series Aluminum Electrolytic Capacitors (Low Impedance, Miniature Sized) MERITEK DIMENSIONS (Ø12.5~ Ø18) Item 12.5 x 20 Lead wire diameter d Body height A Intervals of bodies P Intervals of punched holes Distance between holes and lead wire Distance between lead and lead F 16 x 25 16 x 31.5 21.5 26.5 16 x 35.5 18 x 35.5 0.8 31.5 26.5 15.0 33 37.0 37.0 MAX ±1.0 15.0 ±0.7 7.5 ±1.0 +0.8 -0.2 7.5 18.0 15.0 ±0.5 MIN W1 9.0 ±0.5 W2 1.5 MAX H Distance between body top and tape center H1 16.5 40.5 45.5 18.5 50.5 46.5 53.5 ±0.5 56.5 56.5 Fig 5. Fig 6. MAX D0 4.0 ±0.3 L 11.0 MAX t 0.6 ±0.3 Deviation of body alignment ∆h 0 ±2.0 Deviation of body alignment ∆h1 0 ±1.0 Base and adhesive tape thickness Fig 5. Fig 6. ±0.2 3.75 5.0 Remark ±0.05 30.0 5.0 Tolerance W W0 Distance between body bottom and tape center Punched hole diameter Length of not good lead slit 12.5 x 30 0.6 P1 P2 Deviation between holes and base tape Deviation between adhesive and base tape 12.5 x 25 P0 Distance between holes and bodies Base tape width Adhesive tape width Case Size Symbol Rev. 7a Aluminum Electrolytic Capacitors REW Series (Low Impedance, Miniature Sized) MERITEK Rev. 7a Aluminum Electrolytic Capacitors REW Series (Low Impedance, Miniature Sized) MERITEK SOLDERABILITY Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the liquid solder 2mm, the dipping lead must be adherent 95% fresh tin at least. RESISTANCE TO SOLDERING HEAT Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room temperature, should do final measurements, the values are following: (A) Capacitance change: ≦ ±10% of initial value (B) Dissipation factor: ≦ initial specified value (C) Leakage current: ≦ initial specified value (D) Visual: No damage Rev. 7a