RF Series Aluminum Electrolytic Capacitors (High R.C. , High Reliability) MERITEK FEATURES High ripple current, low E.S.R. and long life. Suitable for electronic ballast, adaptor and switching power SPECIFICATIONS Item Characteristic Operating Temp Range - 40 ~ +105C - 25 ~ +105C Rated Working Voltage 160 ~ 400VDC 450VDC Capacitance Tolerance (120Hz 20C) 20%(M) I 0.06CV+10(uA) Leakage Current I : Leakage Current (A) C : Rated Capacitance(F) V : Working Voltage (V) (20C) ＊After 2 minutes Surge Voltage W.V. 160 200 250 400 450 (20C) S.V. 200 250 300 450 500 Dissipation Factor ( tan ) (120Hz 20C) W.V. 160 200 250 400 450 tan 0.15 0.15 0.15 0.24 0.24 Low Temperature Stability Impedance ratio at 120Hz Rated Voltage (V) 160~250 400 450 -25C / +20C 3 6 6 -40C / +20C 4 6 - After hours (D ≤ 8mm 2000hrs, D ≥ 10mm 3000hrs) application of W.V. and +105C ripple current value , the capacitor shall meet the following limits. ( DC + ripple peak voltage rated working voltage ) Load Life Shelf Life Capacitance Change 20% of initial value. Dissipation Factor 200% of initial specified value Leakage Current initial specified value At +105C no voltage application after 1000 hours, the capacitor shall meet the limits for load life characteristics. ( with voltage treatment ) PART NUMBER SYSTEM DIMENSIONS (mm) RF 160V 101 M TA 16x25 Meritek Series Rated Voltage Rated Capacitance Express in micro farad(uF), First two digits are significant figures, Third digit denotes number of zeros. ‘R’ denotes decimal point for values less than 10uF Tolerance M - 20% Package Code TA Tape & Ammo TR Tape & Reel Blank Case size – (D) Diameter x (L) Length in mm (Optional) D F d a 10 5.0 0.6 1.5 12.5 5.0 0.6 1.5 16 7.5 0.8 1.5 18 7.5 0.8 1.5 Rev. 7a Aluminum Electrolytic Capacitors RF Series (High R.C. , High Reliability) MERITEK RIPPLE CURRENT COEFFICIENTS Frequency(Hz) W.V. D=10mm 160~450 D>10mm 120 0.25 0.35 1k 10k Multiplier 0.61 0.88 0.66 0.89 100k Temperature(C) 65 75 85 95 105 Multiplier 1.8 1.65 1.50 1.25 1.00 1.0 1.0 CASE SIZE & MAX RIPPLE CURRENT V Cap. (uF) Item 4.7 10 22 33 47 68 100 220 V Cap. (uF) Item 2.2 3.3 4.7 10 22 33 47 68 100 120 150 180 DxL 160 IMP. R.C. Case size Max. impedance Max. ripple current DxL 200 IMP. R.C. DxL 10x16 10x20 12.5x20 12.5x25 16x25 16x31.5 18x35.5 18x40 10x16 10x20 10x20 12.5x20 12.5x20 16x25 16x35.5 1.47 0.80 0.62 0.50 0.39 0.32 0.17 220 350 430 550 660 890 1540 10x16 10x20 12.5x20 12.5x25 12.5x25 16x31.5 18x35.5 1.47 0.80 0.62 0.50 0.39 0.32 0.17 220 350 460 610 730 980 1640 DxL 400 IMP. R.C. DxL 450 IMP. R.C. 10x20 10x25 12.5x25 16x25 16x31.5 16x31.5 16x31.5 18x31.5 18x35.5 18x40 18x40 2.60 2.20 1.72 0.94 0.73 0.59 0.46 0.38 0.32 0.26 0.23 170 220 340 510 690 820 990 1280 1480 1740 1910 10x16 10x20 12.5x20 12.5x25 16x31.5 16x31.5 18x31.5 4.94 4.11 3.47 2.72 1.48 1.15 0.92 110 150 190 300 500 620 780 : DxL (mm) :Ω 20C 100kHz : mA(rms) 105C 100kHz 250 IMP. R.C. 3.45 2.70 1.47 1.15 0.92 0.71 0.59 0.31 150 240 380 510 610 810 1110 1730 Rev. 7a RF Series Aluminum Electrolytic Capacitors (High R.C. , High Reliability) MERITEK TAPING SPECIFICATION Lead taping is designed for automatic insertion equipment. Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type. DIMENSIONS (Ø4~ Ø10) Item Symbol Case Size 4x5 5 x 5 6.3x5 8 x 5 4x7 5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16 0.45 0.5 10x18 10x20 Tolerance Lead wire diameter d Body height A Intervals of bodies P 12.7 ±1.0 Intervals of punched holes P0 12.7 ±0.2 6.0 8.0 12.5 13 14 0.6 ±0.05 17.5 19.5 21.5 MAX 3.85 Distance between holes and lead wire P1 5.35 5.1 5.1 5.6 Distance between holes and bodies 5.35 5.1 5.35 5.1 5.1 5.6 5.1 ±0.7 5.1 5.35 5.1 4.6 5.35 5.1 P2 F 6.35 2.0 2.5 2.5 2.0 2.5 2.5 Fig 1. Fig 4. Fig 2. Fig 3. 4.6 ±1.0 Fig 1. Fig 4. 5.0 Distance between lead and lead Remark +0.8 -0.2 2.5 Fig 2. F1:5.0 +0.5 -1.0 1.5 2.0 2.5 2.5 1.5 Fig 3. F1:5.0 2.0 2.5 3.5 2.0 2.5 3.5 +0.5 -1.0 Base tape width W W0 18.0 ±0.5 12.5 MIN Deviation between holes and base tape W1 9.0 ±0.5 Deviation between adhesive and base tape W2 1.5 MAX Adhesive tape width 17.5 18.5 20.0 17.5 18.5 18.5 18.5 Distance between body bottom and tape center H Lead wire clinched height H0 Distance between body top and tape center H1 Punched hole diameter D0 4.0 ±0.3 Length of not good lead slit L 11.0 MAX Base and adhesive tape thickness t 0.6 ±0.3 Deviation of body alignment ∆h 0 ±2.0 Deviation of body alignment ∆h1 0 ±1.0 ±0.5 16.0 24.5 Fig 1. Fig 4. Fig 2. Fig 3. ±0.5 27.5 32.5 33.0 36.0 38.0 41.0 MAX Rev. 7a RF Series Aluminum Electrolytic Capacitors (High R.C. , High Reliability) MERITEK DIMENSIONS (Ø12.5~ Ø18) Item 12.5 x 20 Lead wire diameter d Body height A Intervals of bodies P Intervals of punched holes P0 Distance between holes and lead wire P1 Distance between holes and bodies Distance between lead and lead Base tape width Adhesive tape width Deviation between holes and base tape Deviation between adhesive and base tape Case Size Symbol 12.5 x 25 12.5 x 30 16 x 25 16 x 31.5 0.6 21.5 26.5 16 x 35.5 18 x 35.5 0.8 31.5 26.5 15.0 33 37.0 37.0 3.75 5.0 ±0.7 ±1.0 +0.8 -0.2 7.5 W W0 18.0 ±0.5 15.0 MIN W1 9.0 ±0.5 W2 1.5 MAX Distance between body bottom and tape center H Distance between body top and tape center H1 Punched hole diameter D0 4.0 ±0.3 Length of not good lead slit L 11.0 MAX t 0.6 ±0.3 ∆h 0 ±2.0 ∆h1 0 ±1.0 Base and adhesive tape thickness Deviation of body alignment Deviation of body alignment 16.5 40.5 45.5 18.5 50.5 46.5 Fig 5. Fig 6. ±0.2 7.5 F MAX ±1.0 15.0 P2 Remark ±0.05 30.0 5.0 Tolerance 53.5 ±0.5 56.5 56.5 Fig 5. Fig 6. MAX Rev. 7a Aluminum Electrolytic Capacitors RF Series (High R.C. , High Reliability) MERITEK Rev. 7a Aluminum Electrolytic Capacitors RF Series (High R.C. , High Reliability) MERITEK SOLDERABILITY Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the liquid solder 2mm, the dipping lead must be adherent 95% fresh tin at least. RESISTANCE TO SOLDERING HEAT Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room temperature, should do final measurements, the values are following: (A) Capacitance change: ≦ ±10% of initial value (B) Dissipation factor: ≦ initial specified value (C) Leakage current: ≦ initial specified value (D) Visual: No damage Rev. 7a