20140228081154cWM2tmd

NPM Series
Aluminum Electrolytic Capacitors
( Non Polarity,7mmL 85°C )
MERITEK
FEATURES
 Non polarity series with 7mm height
SPECIFICATIONS
Item
Characteristic
Operating Temp Range
- 40 ~ +85C
Rated Working Voltage
6.3 ~ 50VDC
Capacitance Tolerance
(120Hz 20C)
 20%(M)
I  0.05CV or 10(uA)
Leakage Current
I : Leakage Current (A)
C : Rated Capacitance(F)
V : Working Voltage (V)
(20C)
＊Whichever is greater after 2 minutes
Surge Voltage
(20C)
Dissipation Factor ( tan  )
(120Hz 20C)
Low Temperature Stability
W.V.
6.3
10
16
25
35
50
S.V.
8
13
20
32
44
63
W.V.
6.3
10
16
25
35
50
tan 
0.24
0.20
0.17
0.15
0.12
0.12
Impedance ratio at 120Hz
Rated Voltage (V)
Load Life
Shelf Life
6.3
10
16
25
35
50
-25C / +20C
4
3
2
2
2
2
-40C / +20C
10
8
6
4
3
3
After 1000 hours application of W.V. and +85C ripple current value , the capacitor shall meet
the following limits. ( DC + ripple peak voltage  rated working voltage ) ( The polarity need to
exchange every 250 hours )
Capacitance Change
 20% of initial value.
Dissipation Factor
 150% of initial specified value
Leakage Current
 initial specified value
At +85C no voltage application after 500 hours the capacitor shall meet the following limits.
( with voltage treatment )
Capacitance Change
 20% of initial value.
Dissipation Factor
 200% of initial specified value
Leakage Current
 200% of initial specified value
PART NUMBER SYSTEM
DIMENSIONS (mm)
NPM 10V 101 M TA 8x7
Meritek Series
Rated Voltage
Rated Capacitance
Express in micro farad(uF), First two digits are
significant figures, Third digit denotes number of
zeros. ‘R’ denotes decimal point for values less
than 10uF
Tolerance
M - 20%
Package
Code
TA
Tape & Ammo
TR
Tape & Reel
Blank
Case size – (D) Diameter x (L) Length in mm (Optional)
D
F
d

4
1.5
0.45
1.0
5
2.0
0.45
1.0
6.3
2.5
0.45
1.0
8
3.5
0.5
1.0
Rev. 7a
NPM Series
Aluminum Electrolytic Capacitors
( Non Polarity,7mmL 85°C )
CASE SIZE & MAX RIPPLE CURRENT
V
Cap.
(uF) Item
0.1
0.22
0.33
0.47
1.0
2.2
3.3
4.7
10
22
33
47
100
6.3
DxL
10
R.C.
DxL
16
R.C.

5x7
5x7
6.3x7
8x7

35
43
60
100
4x7
5x7
6.3x7
6.3x7
8x7
23
38
55
65
110
DxL
R.C.
4x7
5x7
6.3x7
6.3x7
6.3x7
8x7

17
28
47
60
70
120
MERITEK
Case size
: DxL
(mm)
Max. ripple current
: mA(rms) 85C 120Hz
25
35
50
DxL
R.C.
DxL
R.C.
DxL
R.C.

4x7
3

4x7
4

4x7
5

4x7
6

4x7
9

4x7
14
5x7
16
4x7
15
5x7
19
5x7
19
5x7
20
5x7
23
6.3x7
26
6.3x7
34
6.3x7
38
8x7
44
6.3x7
50
8x7
65
8x7
65
8x7
70
8x7
80
8x7
85
All blank voltage on sleeve marking is the same voltage as “” point to.
Rev. 7a
NPM Series
Aluminum Electrolytic Capacitors
( Non Polarity,7mmL 85°C )
MERITEK
TAPING SPECIFICATION


Lead taping is designed for automatic insertion equipment.
Capacitors with case size of 18mm x 35.5mm or smaller are available in taping type.
DIMENSIONS (Ø4~ Ø10)
Item
Symbol
Case Size
4x5
5 x 5 6.3x5 8 x 5
4x7
5 x 7 6.3x7 8 x 7 5 x 11 6.3x11 8 x 11.5 10x12.5 10x16
0.45
0.5
10x18 10x20
Tolerance
Lead wire diameter
d
Body height
A
Intervals of bodies
P
12.7
±1.0
Intervals of punched
holes
P0
12.7
±0.2
6.0
8.0
12.5
13
14
0.6
±0.05
17.5 19.5 21.5
MAX
3.85
Distance between
holes and lead wire
P1
5.35 5.1 5.1
5.6
Distance between
holes and bodies
5.35 5.1
5.35 5.1 5.1
5.6
5.1
±0.7
5.1
5.35 5.1 4.6 5.35 5.1
P2
F
6.35
2.0 2.5
2.5
2.0 2.5
2.5
Fig 1.
Fig 4.
Fig 2.
Fig 3.
4.6
±1.0
Fig 1.
Fig 4.
5.0
Distance between
lead and lead
Remark
+0.8
-0.2
2.5
Fig 2.
F1:5.0
+0.5
-1.0
1.5
2.0 2.5 2.5 1.5
Fig 3.
F1:5.0
2.0 2.5 3.5 2.0 2.5 3.5
+0.5
-1.0
Base tape width
W
W0
18.0
±0.5
12.5
MIN
Deviation between
holes and base tape
W1
9.0
±0.5
Deviation between
adhesive and base
tape
W2
1.5
MAX
Adhesive tape width
17.5
18.5
20.0
17.5
18.5
18.5
18.5
Distance between
body bottom and tape
center
H
Lead wire clinched
height
H0
Distance between
body top and tape
center
H1
Punched hole
diameter
D0
4.0
±0.3
Length of not good
lead slit
L
11.0
MAX
Base and adhesive
tape thickness
t
0.6
±0.3
Deviation of body
alignment
∆h
0
±2.0
Deviation of body
alignment
∆h1
0
±1.0
±0.5
16.0
24.5
Fig 1.
Fig 4.
Fig 2.
Fig 3.
±0.5
27.5
32.5
33.0 36.0 38.0 41.0
MAX
Rev. 7a
NPM Series
Aluminum Electrolytic Capacitors
( Non Polarity,7mmL 85°C )
MERITEK
DIMENSIONS (Ø12.5~ Ø18)
Item
Lead wire diameter
d
Body height
A
Intervals of bodies
P
Intervals of punched
holes
Distance between
holes and lead wire
Distance between
lead and lead
F
21.5
26.5
12.5 x 30
16 x 25
16 x 31.5
31.5
26.5
33
0.6
16 x 35.5 18 x 35.5
0.8
15.0
37.0
MAX
±1.0
15.0
±0.7
7.5
±1.0
+0.8
-0.2
7.5
18.0
15.0
±0.5
MIN
W1
9.0
±0.5
W2
1.5
MAX
H
Distance between
body top and tape
center
H1
16.5
40.5
45.5
18.5
50.5
46.5
53.5
±0.5
56.5
56.5
Fig 5.
Fig 6.
MAX
D0
4.0
±0.3
L
11.0
MAX
t
0.6
±0.3
Deviation of body
alignment
∆h
0
±2.0
Deviation of body
alignment
∆h1
0
±1.0
Base and adhesive
tape thickness
Fig 5.
Fig 6.
±0.2
3.75
5.0
Remark
±0.05
37.0
30.0
5.0
Tolerance
W
W0
Distance between
body bottom and tape
center
Punched hole
diameter
Length of not good
lead slit
12.5 x 25
P1
P2
Deviation between
holes and base tape
Deviation between
adhesive and base
tape
12.5 x 20
P0
Distance between
holes and bodies
Base tape width
Adhesive tape width
Case Size
Symbol
Rev. 7a
Aluminum Electrolytic Capacitors
NPM Series
( Non Polarity,7mmL 85°C )
MERITEK
Rev. 7a
Aluminum Electrolytic Capacitors
NPM Series
( Non Polarity,7mmL 85°C )
MERITEK
SOLDERABILITY
Capacitor lead wire is dipping into the oven, and then, dipping in 245±3℃, solder liquid for 3±0.5 seconds, the substance is above the
liquid solder 2mm, the dipping lead must be adherent 95% fresh tin at least.
RESISTANCE TO SOLDERING HEAT
Put capacitor lead wire to dip 260±5℃ in solder liquor away the body 2mm, after 10±1 seconds taken out, after 2 hours in room
temperature, should do final measurements, the values are following:
(A) Capacitance change: ≦ ±10% of initial value
(B) Dissipation factor: ≦ initial specified value
(C) Leakage current: ≦ initial specified value
(D) Visual: No damage
Rev. 7a