Data Sheet

LPC11U6x
32-bit ARM Cortex-M0+ microcontroller; up to 256 KB flash
and 36 KB SRAM; 4 KB EEPROM; USB; 12-bit ADC
Rev. 1.2 — 26 May 2014
Product data sheet
1. General description
The LPC11U6x are an ARM Cortex-M0+ based, low-cost 32-bit MCU family operating at
CPU frequencies of up to 50 MHz. The LPC11U6x support up to 256 KB of flash memory,
a 4 KB EEPROM, and 36 KB of SRAM.
The ARM Cortex-M0+ is an easy-to-use, energy-efficient core using a two-stage pipeline
and fast single-cycle I/O access.
The peripheral complement of the LPC11U6x includes a DMA controller, a CRC engine,
one full-speed USB device controller with XTAL-less low-speed mode, two I2C-bus
interfaces, up to five USARTs, two SSP interfaces, PWM/timer subsystem with six
configurable multi-purpose timers, a Real-Time Clock, one 12-bit ADC, temperature
sensor, function-configurable I/O ports, and up to 80 general-purpose I/O pins.
For additional documentation related to the LPC11U6x parts, see Section 17
“References”.
2. Features and benefits
 System:
 ARM Cortex-M0+ processor (version r0p1), running at frequencies of up to 50 MHz
with single-cycle multiplier and fast single-cycle I/O port.
 ARM Cortex-M0+ built-in Nested Vectored Interrupt Controller (NVIC).
 AHB Multilayer matrix.
 System tick timer.
 Serial Wire Debug (SWD) and JTAG boundary scan modes supported.
 Micro Trace Buffer (MTB) supported.
 Memory:
 Up to 256 KB on-chip flash programming memory with page erase.
 Up to 32 KB main SRAM.
 Up to two additional SRAM blocks of 2 KB each.
 Up to 4 KB EEPROM.
 ROM API support:
 Boot loader.
 USART drivers.
 I2C drivers.
 USB drivers.
 DMA drivers.
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller







LPC11U6x
Product data sheet
 Power profiles.
 Flash In-Application Programming (IAP) and In-System Programming (ISP).
 32-bit integer division routines.
Digital peripherals:
 Simple DMA engine with 16 channels and programmable input triggers.
 High-speed GPIO interface connected to the ARM Cortex-M0+ IO bus with up to 80
General-Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors,
programmable open-drain mode, input inverter, and programmable glitch filter and
digital filter.
 Pin interrupt and pattern match engine using eight selectable GPIO pins.
 Two GPIO group interrupt generators.
 CRC engine.
Configurable PWM/timer subsystem (two 16-bit and two 32-bit standard
counter/timers, two State-Configurable Timers (SCTimer/PWM)) that provides:
 Up to four 32-bit and two 16-bit counter/timers or two 32-bit and six 16-bit
counter/timers.
 Up to 21 match outputs and 16 capture inputs.
 Up to 19 PWM outputs with 6 independent time bases.
Windowed WatchDog timer (WWDT).
Real-time Clock (RTC) in the always-on power domain with separate battery supply
pin and 32 kHz oscillator.
Analog peripherals:
 One 12-bit ADC with up to 12 input channels with multiple internal and external
trigger inputs and with sample rates of up to 2 Msamples/s. The ADC supports two
independent conversion sequences.
 Temperature sensor.
Serial interfaces:
 Up to five USART interfaces, all with DMA, synchronous mode, and RS-485 mode
support. Four USARTs use a shared fractional baud generator.
 Two SSP controllers with DMA support.
 Two I2C-bus interfaces. One I2C-bus interface with specialized open-drain pins
supports I2C Fast-mode plus.
 USB 2.0 full-speed device controller with on-chip PHY. XTAL-less low-speed mode
supported.
Clock generation:
 12 MHz internal RC oscillator trimmed to 1 % accuracy for 25 C  Tamb  +85 C
that can optionally be used as a system clock.
 On-chip 32 kHz oscillator for RTC.
 Crystal oscillator with an operating range of 1 MHz to 25 MHz. Oscillator pins are
shared with the GPIO pins.
 Programmable watchdog oscillator with a frequency range of 9.4 kHz to 2.3 MHz.
 PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal.
 A second, dedicated PLL is provided for USB.
 Clock output function with divider that can reflect the crystal oscillator, the main
clock, the IRC, or the watchdog oscillator.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
2 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
 Power control:
 Integrated PMU (Power Management Unit) to minimize power consumption.
 Reduced power modes: Sleep mode, Deep-sleep mode, Power-down mode, and
Deep power-down mode.
 Wake-up from Deep-sleep and Power-down modes on external pin inputs and
USART activity.
 Power-On Reset (POR).
 Brownout detect.
 Unique device serial number for identification.
 Single power supply (2.4 V to 3.6 V).
 Separate VBAT supply for RTC.
 Operating temperature range 40 °C to 105 °C.
 Available as LQFP48, LQFP64, and LQFP100 packages.
3. Applications
 Three-phase e-meter
 GPS tracker
 Gaming accessories
LPC11U6x
Product data sheet
 Car radio
 Medical monitor
 PC peripherals
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
3 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC11U66JBD48
LQFP48
plastic low profile quad flat package; 48 leads; body 7  7  1.4 mm
SOT313-2
LPC11U67JBD48
LQFP48
plastic low profile quad flat package; 48 leads; body 7  7  1.4 mm
SOT313-2
LPC11U67JBD64
LQFP64
plastic low profile quad flat package; 64 leads; body 10  10  1.4 mm
SOT314-2
LPC11U67JBD100
LQFP100
plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm
SOT407-1
LPC11U68JBD48
LQFP48
plastic low profile quad flat package; 48 leads; body 7  7  1.4 mm
SOT313-2
LPC11U68JBD64
LQFP64
plastic low profile quad flat package; 64 leads; body 10  10  1.4 mm
SOT314-2
LPC11U68JBD100
LQFP100
plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm
SOT407-1
4.1 Ordering options
USART4
12-bit
ADC
channels
GPIO
N
N
2
2
6
8
34
N
N
2
2
6
8
34
N
N
2
2
6
10
48
Y
Y
Y
2
2
6
12
80
Y
N
N
2
2
6
8
34
USART2
I2C SSP Timers
with
PWM
Flash/ EEPROM/ SRAM/ USB
KB
KB
KB
USART1
USART3
Ordering options
Type number
USART0
Table 2.
LPC11U66JBD48
64
4
12
1
Y
Y
Y
LPC11U67JBD48
128
4
20
1
Y
Y
Y
LPC11U67JBD64
128
4
20
1
Y
Y
Y
LPC11U67JBD100
128
4
20
1
Y
Y
LPC11U68JBD48
256
4
36
1
Y
Y
LPC11U68JBD64
256
4
36
1
Y
Y
Y
N
N
2
2
6
10
48
LPC11U68JBD100
256
4
36
1
Y
Y
Y
Y
Y
2
2
6
12
80
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
4 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
5. Marking
n
n
Terminal 1 index area
1
aaa-011231
Fig 1.
LQFP64/100 package marking
Terminal 1 index area
Fig 2.
1
aaa-011232
LQFP48 package marking
The LPC11U6x devices typically have the following top-side marking for LQFP100
packages:
LPC11U6xJBD100
xxxxxx xx
xxxyywwxR[x]
The LPC11U6x devices typically have the following top-side marking for LQFP64
packages:
LPC11U6xJ
xxxxxx xx
xxxyywwxR[x]
The LPC11U6x devices typically have the following top-side marking for LQFP48
packages:
LPC11U6xJ
xx xx
xxxyy
wwxR[x]
Field ‘yy’ states the year the device was manufactured. Field ‘ww’ states the week the
device was manufactured during that year. Field ‘R’ states the chip revision.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
5 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
6. Block diagram
LPC16Uxx
PROCESSOR CORE
ARM
CORTEX-M0+
SWD TEST/DEBUG
INTERFACE
NVIC
HS GPIO+
SYSTICK
MEMORY
PORT0/1/2
256/128 kB FLASH
PINT/
PATTERN MATCH
AHB MULTILAYER
MATRIX
4 kB EEPROM
36/20 kB SRAM
PINTSEL
AHB/APB BRIDGES
GINT0/1
ROM
ANALOG PERIPHERALS
12-bit ADC0
TEMPERATURE SENSOR
TRIGGER MUX
IOCON
pads
n
PWM/TIMER SUBSYSTEM
SCTIMER0/
PWM
CT16B0
SCTIMER1/
PWM
CT16B1
DMA
CT32B0
DMA TRIGGER
CT32B1
SERIAL PERIPHERALS
USART0
CLOCK
GENERATION
USART1
USART2
SSP0
FM+ I2C0
USART3(1)
USART4(1)
SSP1
I2C1
PRECISION
IRC
WATCHDOG
OSCILLATOR
SYSTEM
OSCILLATOR
ALWAYS-ON POWER DOMAIN
RTC
RTC
OSCILLATOR
FS USB/
PHY
SYSTEM
PLL
USB
PLL
SYSTEM TIMER
GENERAL PURPOSE
BACKUP REGISTERS
WWDT
SYSTEM/MEMORY CONTROL
SYSCON
IOCON
PMU
CRC
FLASH CTRL
EEPROM CTRL
aaa-010773
Gray-shaded blocks show peripherals that can provide hardware triggers for DMA transfers or have DMA request lines.
(1) Available on LQFP100 packages only.
Fig 3.
LPC11U6x block diagram
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
6 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
7. Pinning information
25 PIO1_21
26 PIO0_8
27 PIO0_9
28 SWCLK/PIO0_10
29 PIO0_22
30 TDI/PIO0_11
31 TMS/PIO0_12
32 TDO/PIO0_13
33 TRST/PIO0_14
34 VREFP
35 VREFN
36 PIO1_13
7.1 Pinning
SWDIO/PIO0_15 37
24 PIO0_7
PIO0_16/WAKEUP 38
23 PIO0_6
PIO0_23 39
22 PIO1_24
VDDA 40
21 PIO2_7
VSSA 41
20 USB_DP
PIO0_17 42
19 USB_DM
LPC11U6XJBD48
VSS 43
18 PIO1_23
VDD 44
17 PIO0_21
PIO0_18 45
16 PIO0_5
PIO0_19 46
15 PIO0_4
VBAT 47
14 PIO0_3
Fig 4.
PIO2_2 12
PIO0_2 11
PIO2_5 9
PIO0_20 10
VDD 8
PIO2_1/XTALOUT 7
VSS 5
PIO2_0/XTALIN 6
PIO0_1 4
RESET/PIO0_0 3
VSS 2
13 PIO1_20
RTCXOUT 1
RTCXIN 48
aaa-007794
LQFP48 pinning
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
7 of 96
LPC11U6x
NXP Semiconductors
33 PIO2_18
34 VDD
35 PIO1_21
36 PIO2_19
37 PIO0_8
38 PIO0_9
39 SWCLK/PIO0_10
40 PIO0_22
41 PIO1_29
42 TDI/PIO0_11
43 TMS/PIO0_12
44 PIO1_30
45 TDO/PIO0_13
46 TRST/PIO0_14
47 VREFP
48 VREFN
32-bit ARM Cortex-M0+ microcontroller
PIO1_13 49
32 PIO2_15
SWDIO/PIIO0_15 50
31 PIO1_28
PIO0_16/WAKEUP 51
30 PIO0_7
PIO0_23 52
29 PIO0_6
VDDA 53
28 PIO1_24
VSSA 54
27 PIO2_7
PIO1_9 55
26 USB_DP
PIO0_17 56
25 USB_DM
LPC11U6XJBD64
VSS 57
23 PIO1_23
VDD 59
22 PIO0_21
PIO0_18 60
21 PIO0_5
PIO0_19 61
20 PIO0_4
PIO1_0 62
19 PIO0_3
PIO2_2 16
PIO1_26 15
PIO0_2 14
PIO1_10 13
PIO2_5 11
PIO0_20 12
VDD 10
PIO2_1 9
VSS 7
PIO2_0 8
PIO1_7 6
PIO0_1 5
RESET/PIO0_0
4
17 PIO1_27
VSS 3
18 PIO1_20
RTCXOUT 2
VBAT 63
PIO1_19 64
RTCXIN 1
aaa-007795
51
LQFP64 pinning
75
Fig 5.
24 PIO2_6
VDD 58
76
50
LPC11U6XJBD100
25
26
1
100
aaa-007796
Fig 6.
LPC11U6x
Product data sheet
LQFP100 pinning
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
8 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
7.2 Pin description
LQFP100
RESET/PIO0_0
LQFP64
Symbol
LQFP48
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
3
4
8
[8]
Reset Type
state[1]
Description of pin functions
I; PU
RESET — External reset input with 20 ns glitch filter. A
LOW-going pulse as short as 50 ns on this pin resets the
device, causing I/O ports and peripherals to take on their
default states, and processor execution to begin at address
0. This pin also serves as the debug select input. LOW
level selects the JTAG boundary scan. HIGH level selects
the ARM SWD debug mode.
I
In deep power-down mode, this pin must be pulled HIGH
externally. The RESET pin can be left unconnected or be
used as a GPIO pin if an external RESET function is not
needed and Deep power-down mode is not used.
PIO0_1
PIO0_2
PIO0_3
PIO0_4
PIO0_5
LPC11U6x
Product data sheet
4
11
5
14
14 19
15 20
16 21
9
19
30
31
32
[6]
[6]
[6]
[7]
[7]
I; PU
I; PU
I; PU
IA
IA
IO
PIO0_0 — General-purpose digital input/output pin.
IO
PIO0_1 — General-purpose digital input/output pin. A LOW
level on this pin during reset starts the ISP command
handler or the USB device enumeration.
O
CLKOUT — Clockout pin.
O
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
O
USB_FTOGGLE — USB 1 ms Start-of-Frame signal.
IO
PIO0_2 — General-purpose port 0 input/output 2.
IO
SSP0_SSEL — Slave select for SSP0.
I
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
-
R_0 — Reserved.
IO
PIO0_3 — General-purpose digital input/output pin. A LOW
level on this pin during reset starts the ISP command
handler. A HIGH level during reset starts the USB device
enumeration.
I
USB_VBUS — Monitors the presence of USB bus power.
-
R_1 — Reserved.
IO
PIO0_4 — General-purpose port 0 input/output 4
(open-drain).
IO
I2C0_SCL — I2C-bus clock input/output (open-drain).
High-current sink only if I2C Fast-mode Plus is selected in
the I/O configuration register.
-
R_2 — Reserved.
IO
PIO0_5 — General-purpose port 0 input/output 5
(open-drain).
IO
I2C0_SDA — I2C-bus data input/output (open-drain).
High-current sink only if I2C Fast-mode Plus is selected in
the I/O configuration register.
-
R_3 — Reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
9 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
PIO0_7
PIO0_8
PIO0_9
SWCLK/PIO0_10
TDI/PIO0_11
TMS/PIO0_12
LPC11U6x
Product data sheet
LQFP100
PIO0_6
23 29
44
LQFP48
Symbol
LQFP64
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
24 30
26 37
27 38
28 39
30 42
31 43
45
58
59
60
64
66
[6]
[5]
[6]
[6]
[6]
[3]
[3]
Reset Type
state[1]
Description of pin functions
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO0_6 — General-purpose port 0 input/output 6.
-
R — Reserved.
IO
SSP0_SCK — Serial clock for SSP0.
-
R_4 — Reserved.
IO
PIO0_7 — General-purpose port 0 input/output 7
(high-current output driver).
I
U0_CTS — Clear To Send input for USART.
-
R_5 — Reserved.
IO
I2C1_SCL — I2C-bus clock input/output. This pin is not
open-drain.
IO
PIO0_8 — General-purpose port 0 input/output 8.
IO
SSP0_MISO — Master In Slave Out for SSP0.
O
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
-
R_6 — Reserved.
IO
PIO0_9 — General-purpose port 0 input/output 9.
IO
SSP0_MOSI — Master Out Slave In for SSP0.
O
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
-
R_7 — Reserved.
IO
SWCLK — Serial Wire Clock. SWCLK is enabled by
default on this pin. In boundary scan mode: TCK (Test
Clock).
IO
PIO0_10 — General-purpose digital input/output pin.
IO
SSP0_SCK — Serial clock for SSP0.
O
CT16B0_MAT2 — 16-bit timer0 MAT2
IO
TDI — Test Data In for JTAG interface. In boundary scan
mode only.
IO
PIO0_11 — General-purpose digital input/output pin.
AI
ADC_9 — A/D converter, input channel 9.
O
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
O
U1_RTS — Request To Send output for USART1.
IO
U1_SCLK — Serial clock input/output for USART1 in
synchronous mode.
IO
TMS — Test Mode Select for JTAG interface. In boundary
scan mode only.
IO
PIO0_12 — General-purpose digital input/output pin.
AI
ADC_8 — A/D converter, input channel 8.
I
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
I
U1_CTS — Clear To Send input for USART1.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
10 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
TRST/PIO0_14
SWDIO/PIO0_15
PIO0_16/WAKEUP
PIO0_17
PIO0_18
PIO0_19
LPC11U6x
Product data sheet
LQFP100
TDO/PIO0_13
32 45
68
LQFP48
Symbol
LQFP64
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
33 46
37 50
38 51
42 56
45 60
46 61
69
81
82
90
94
95
[3]
[3]
[3]
[4]
[6]
[6]
[6]
Reset Type
state[1]
Description of pin functions
I; PU
IO
TDO — Test Data Out for JTAG interface. In boundary scan
mode only.
IO
PIO0_13 — General-purpose digital input/output pin.
AI
ADC_7 — A/D converter, input channel 7.
O
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
I
U1_RXD — Receiver input for USART1.
IO
TRST — Test Reset for JTAG interface. In boundary scan
mode only.
IO
PIO0_14 — General-purpose digital input/output pin.
AI
ADC_6 — A/D converter, input channel 6.
O
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
O
U1_TXD — Transmitter output for USART1.
IO
SWDIO — Serial Wire Debug I/O. SWDIO is enabled by
default on this pin. In boundary scan mode: TMS (Test
Mode Select).
IO
PIO0_15 — General-purpose digital input/output pin.
AI
ADC_3 — A/D converter, input channel 3.
O
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
IO
PIO0_16 — General-purpose digital input/output pin. This
pin also serves as the Deep power-down mode wake-up
pin with 20 ns glitch filter. Pull this pin HIGH externally
before entering Deep power-down mode. Pull this pin LOW
to exit Deep power-down mode. A LOW-going pulse as
short as 50 ns wakes up the part.
AI
ADC_2 — A/D converter, input channel 2.
O
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
-
R_8 — Reserved.
IO
PIO0_17 — General-purpose digital input/output pin.
O
U0_RTS — Request To Send output for USART0.
I
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
IO
U0_SCLK — Serial clock input/output for USART0 in
synchronous mode.
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO0_18 — General-purpose digital input/output pin.
I
U0_RXD — Receiver input for USART0. Used in UART
ISP mode.
O
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
IO
PIO0_19 — General-purpose digital input/output pin.
O
U0_TXD — Transmitter output for USART0. Used in UART
ISP mode.
O
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
11 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
PIO0_21
PIO0_22
PIO0_23
PIO1_0
PIO1_1
PIO1_2
PIO1_3
PIO1_4
LPC11U6x
Product data sheet
LQFP100
PIO0_20
10 12
17
LQFP48
Symbol
LQFP64
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
17 22
29 40
39 52
-
-
-
-
-
62
-
-
-
-
33
62
83
97
28
55
72
23
[6]
[6]
[3]
[3]
[6]
[6]
[6]
[3]
[6]
Reset Type
state[1]
Description of pin functions
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO0_20 — General-purpose digital input/output pin.
I
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
I
U2_RXD — Receiver input for USART2.
IO
PIO0_21 — General-purpose digital input/output pin.
O
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
IO
SSP1_MOSI — Master Out Slave In for SSP1.
IO
PIO0_22 — General-purpose digital input/output pin.
AI
ADC_11 — A/D converter, input channel 11.
I
CT16B1_CAP1 — Capture input 1 for 16-bit timer 1.
IO
SSP1_MISO — Master In Slave Out for SSP1.
IO
PIO0_23 — General-purpose digital input/output pin.
AI
ADC_1 — A/D converter, input channel 1.
-
R_9 — Reserved.
I
U0_RI — Ring Indicator input for USART0.
IO
SSP1_SSEL — Slave select for SSP1.
IO
PIO1_0 — General-purpose digital input/output pin.
O
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
-
R_10 — Reserved.
O
U2_TXD — Transmitter output for USART2.
IO
PIO1_1 — General-purpose digital input/output pin.
O
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
-
R_11 — Reserved.
O
U0_DTR — Data Terminal Ready output for USART0.
IO
PIO1_2 — General-purpose digital input/output pin.
O
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
-
R_12 — Reserved.
I
U1_RXD — Receiver input for USART1.
IO
PIO1_3 — General-purpose digital input/output pin.
O
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
-
R_13 — Reserved.
IO
I2C1_SDA — I2C-bus data input/output (not open-drain).
AI
ADC_5 — A/D converter, input channel 5.
IO
PIO1_4 — General-purpose digital input/output pin.
I
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
-
R_14 — Reserved.
I
U0_DSR — Data Set Ready input for USART0.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
12 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
PIO1_6
PIO1_7
PIO1_8
PIO1_9
PIO1_10
PIO1_11
PIO1_12
PIO1_13
LPC11U6x
Product data sheet
LQFP100
PIO1_5
LQFP64
Symbol
LQFP48
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
-
-
47
-
-
-
-
-
-
-
-
6
-
55
13
-
-
36 49
98
10
61
86
18
65
89
78
[6]
[6]
[6]
[6]
[3]
[6]
[6]
[6]
[6]
Reset Type
state[1]
Description of pin functions
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO1_5 — General-purpose digital input/output pin.
I
CT32B1_CAP1 — Capture input 1 for 32-bit timer 1.
-
R_15 — Reserved.
I
U0_DCD — Data Carrier Detect input for USART0.
IO
PIO1_6 — General-purpose digital input/output pin.
-
R_16 — Reserved.
I
U2_RXD — Receiver input for USART2.
I
CT32B0_CAP1 — Capture input 1 for 32-bit timer 0.
IO
PIO1_7 — General-purpose digital input/output pin.
-
R_17 — Reserved.
I
U2_CTS — Clear To Send input for USART2.
I
CT16B1_CAP0 — Capture input 0 for 32-bit timer 1.
IO
PIO1_8 — General-purpose digital input/output pin.
-
R_18 — Reserved.
O
U1_TXD — Transmitter output for USART1.
I
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
IO
PIO1_9 — General-purpose digital input/output pin.
I
U0_CTS — Clear To Send input for USART0.
O
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
I
ADC_0 — A/D converter, input channel 0.
IO
PIO1_10 — General-purpose digital input/output pin.
O
U2_RTS — Request To Send output for USART2.
IO
U2_SCLK — Serial clock input/output for USART2 in
synchronous mode.
O
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
IO
PIO1_11 — General-purpose digital input/output pin.
IO
I2C1_SCL — I2C1-bus clock input/output (not open-drain).
O
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
I
U0_RI — Ring Indicator input for USART0.
IO
PIO1_12 — General-purpose digital input/output pin.
IO
SSP0_MOSI — Master Out Slave In for SSP0.
O
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
-
R_21 — Reserved.
IO
PIO1_13 — General-purpose digital input/output pin.
I
U1_CTS — Clear To Send input for USART1.
O
SCT0_OUT3 — SCTimer0/PWM output 3.
-
R_22 — Reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
13 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
PIO1_15
PIO1_16
PIO1_17
PIO1_18
PIO1_19
PIO1_20
PIO1_21
PIO1_22
LPC11U6x
Product data sheet
LQFP100
PIO1_14
LQFP64
Symbol
LQFP48
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
-
-
79
-
-
-
-
-
-
-
-
-
64
13 18
25 35
-
-
87
96
34
43
4
29
56
80
[6]
[6]
[6]
[6]
[6]
[6]
[6]
[6]
[3]
Reset Type
state[1]
Description of pin functions
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO1_14 — General-purpose digital input/output pin.
IO
I2C1_SDA — I2C1-bus data input/output (not open-drain).
O
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
-
R_23 — Reserved.
IO
PIO1_15 — General-purpose digital input/output pin.
IO
SSP0_SSEL — Slave select for SSP0.
O
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
-
R_24 — Reserved.
IO
PIO1_16 — General-purpose digital input/output pin.
IO
SSP0_MISO — Master In Slave Out for SSP0.
O
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
-
R_25 — Reserved.
IO
PIO1_17 — General-purpose digital input/output pin.
I
CT16B0_CAP2 — Capture input 2 for 16-bit timer 0.
I
U0_RXD — Receiver input for USART0.
-
R_26 — Reserved.
IO
PIO1_18 — General-purpose digital input/output pin.
I
CT16B1_CAP1 — Capture input 1 for 16-bit timer 1.
O
U0_TXD — Transmitter output for USART0.
-
R_27 — Reserved.
IO
PIO1_19 — General-purpose digital input/output pin.
I
U2_CTS — Clear To Send input for USART2.
O
SCT0_OUT0 — SCTimer0/PWM output 0.
-
R_28 — Reserved.
IO
PIO1_20 — General-purpose digital input/output pin.
I
U0_DSR — Data Set Ready input for USART0.
IO
SSP1_SCK — Serial clock for SSP1.
O
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
IO
PIO1_21 — General-purpose digital input/output pin.
I
U0_DCD — Data Carrier Detect input for USART0.
IO
SSP1_MISO — Master In Slave Out for SSP1.
I
CT16B0_CAP1 — Capture input 1 for 16-bit timer 0.
IO
PIO1_22 — General-purpose digital input/output pin.
IO
SSP1_MOSI — Master Out Slave In for SSP1.
I
CT32B1_CAP1 — Capture input 1 for 32-bit timer 1.
AI
ADC_4 — A/D converter, input channel 4.
-
R_29 — Reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
14 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
PIO1_24
PIO1_25
PIO1_26
PIO1_27
PIO1_28
PIO1_29
PIO1_30
PIO1_31
LPC11U6x
Product data sheet
LQFP100
PIO1_23
18 23
35
LQFP48
Symbol
LQFP64
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
22 28
-
-
-
-
-
-
-
-
15
17
31
41
44
-
42
100
20
22
46
63
67
48
[6]
[6]
[6]
[6]
[6]
[6]
[3]
[6]
[5]
Reset Type
state[1]
Description of pin functions
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO1_23 — General-purpose digital input/output pin.
O
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
IO
SSP1_SSEL — Slave select for SSP1.
O
U2_TXD — Transmitter output for USART2.
IO
PIO1_24 — General-purpose digital input/output pin.
O
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
IO
I2C1_SDA — I2C-bus data input/output (not open-drain).
IO
PIO1_25 — General-purpose digital input/output pin.
O
U2_RTS — Request To Send output for USART2.
IO
U2_SCLK — Serial clock input/output for USART2 in
synchronous mode.
I
SCT0_IN0 — SCTimer0/PWM input 0.
-
R_30 — Reserved.
IO
PIO1_26 — General-purpose digital input/output pin.
O
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
I
U0_RXD — Receiver input for USART0.
-
R_19 — Reserved.
IO
PIO1_27 — General-purpose digital input/output pin.
O
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
O
U0_TXD — Transmitter output for USART0.
-
R_20 — Reserved.
IO
SSP1_SCK — Serial clock for SSP1.
IO
PIO1_28 — General-purpose digital input/output pin.
I
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
IO
U0_SCLK — Serial clock input/output for USART in
synchronous mode.
O
U0_RTS — Request To Send output for USART0.
IO
PIO1_29 — General-purpose digital input/output pin.
IO
SSP0_SCK — Serial clock for SSP0.
I
CT32B0_CAP1 — Capture input 1 for 32-bit timer 0.
O
U0_DTR — Data Terminal Ready output for USART0.
AI
ADC_10 — A/D converter, input channel 10.
IO
PIO1_30 — General-purpose digital input/output pin.
IO
I2C1_SCL — I2C1-bus clock input/output (not open-drain).
I
SCT0_IN3 — SCTimer0/PWM input 3.
-
R_31 — Reserved.
IO
PIO1_31 — General-purpose digital input/output pin
(high-current output driver).
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
15 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
LQFP100
PIO2_0
LQFP64
Symbol
LQFP48
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
6
8
12
PIO2_1
7
9
PIO2_2
12 16
[10]
Reset Type
state[1]
Description of pin functions
I; PU
13
[10]
I; PU
21
[6]
I; PU
IO
PIO2_0 — General-purpose digital input/output pin.
AI
XTALIN — Input to the oscillator circuit and internal clock
generator circuits. Input voltage must not exceed 1.8 V.
IO
PIO2_1 — General-purpose digital input/output pin.
AO
XTALOUT — Output from the oscillator amplifier.
IO
PIO2_2 — General-purpose digital input/output pin.
O
U3_RTS — Request To Send output for USART3.
IO
U3_SCLK — Serial clock input/output for USART3 in
synchronous mode.
SCT0_OUT1 — SCTimer0/PWM output 1.
PIO2_3
PIO2_4
PIO2_5
PIO2_6
PIO2_7
-
-
9
-
-
-
11
24
21 27
36
41
15
37
40
[6]
[6]
[6]
[6]
[6]
PIO2_8
-
-
2
[6]
PIO2_9
-
-
3
[6]
16
[6]
PIO2_10
-
-
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
PIO2_11
-
-
24
[6]
I; PU
PIO2_12
-
-
25
[6]
I; PU
LPC11U6x
Product data sheet
IO
PIO2_3 — General-purpose digital input/output pin.
I
U3_RXD — Receiver input for USART3.
O
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
IO
PIO2_4 — General-purpose digital input/output pin.
O
U3_TXD — Transmitter output for USART3.
O
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
IO
PIO2_5 — General-purpose digital input/output pin.
I
U3_CTS — Clear To Send input for USART3.
I
SCT0_IN1 — SCTimer0/PWM input 1.
IO
PIO2_6 — General-purpose digital input/output pin.
O
U1_RTS — Request To Send output for USART1.
IO
U1_SCLK — Serial clock input/output for USART1 in
synchronous mode.
I
SCT0_IN2 — SCTimer0/PWM input 2.
IO
PIO2_7 — General-purpose digital input/output pin.
IO
SSP0_SCK — Serial clock for SSP0.
I
SCT0_OUT2 — SCTimer0/PWM output 2.
IO
PIO2_8 — General-purpose digital input/output pin.
I
SCT1_IN0 — SCTimer1/PWM input 0.
IO
PIO2_9 — General-purpose digital input/output pin.
I
SCT1_IN1 — SCTimer1/PWM_IN1
IO
PIO2_10 — General-purpose digital input/output pin.
O
U4_RTS — Request To Send output for USART4.
IO
U4_SCLK — Serial clock input/output for USART4 in
synchronous mode.
IO
PIO2_11 — General-purpose digital input/output pin.
I
U4_RXD — Receiver input for USART4.
IO
PIO2_12 — General-purpose digital input/output pin.
O
U4_TXD — Transmitter output for USART4.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
16 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
PIO2_14
PIO2_15
PIO2_16
PIO2_17
PIO2_18
PIO2_19
PIO2_20
PIO2_21
LQFP100
PIO2_13
LQFP64
Symbol
LQFP48
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
-
-
26
-
32
33
36
-
[6]
27
[6]
49
[6]
50
[6]
51
[6]
52
[6]
57
[6]
Reset Type
state[1]
Description of pin functions
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
IO
PIO2_13 — General-purpose digital input/output pin.
I
U4_CTS — Clear To Send input for USART4.
IO
PIO2_14 — General-purpose digital input/output pin.
I
SCT1_IN2 — SCTimer1/PWM input 2.
IO
PIO2_15 — General-purpose digital input/output pin.
I
SCT1_IN3 — SCTimer1/PWM input 3.
IO
PIO2_16 — General-purpose digital input/output pin.
O
SCT1_OUT0 — SCTimer1/PWM output 0.
IO
PIO2_17 — General-purpose digital input/output pin.
O
SCT1_OUT1 — SCTimer1/PWM output 1.
IO
PIO2_18 — General-purpose port 2 input/output 18.
O
SCT1_OUT2 — SCTimer1/PWM output 2.
IO
PIO2_19 — General-purpose port 2 input/output 19.
O
SCT1_OUT3 — SCTimer1/PWM output 3.
75
[6]
I; PU
IO
PIO2_20 — General-purpose port 2 input/output 20.
76
[6]
I; PU
IO
PIO2_21 — General-purpose port 2 input/output 21.
PIO2_22
-
-
77
[6]
I; PU
IO
PIO2_22 — General-purpose port 2 input/output 22.
PIO2_23
-
-
1
[6]
I; PU
IO
PIO2_23 — General-purpose port 2 input/output 23.
88
[6]
IA
IO
Internal reset status output.
F
-
USB bidirectional D+ line. Pad includes internal 33 Ω series
termination resistor.
RSTOUT
-
-
USB_DP
20 26
39
[9]
USB_DM
19 25
38
[9]
F
-
USB bidirectional D line. Pad includes internal 33 Ω series
termination resistor.
RTCXIN
48 1
5
[2]
-
-
RTC oscillator input. This input should be grounded if the
RTC is not used.
RTCXOUT
1
6
[2]
-
-
RTC oscillator output.
VREFP
34 47
73
-
-
ADC positive reference voltage. If the ADC is not used, tie
VREFP to VDD.
VREFN
35 48
74
-
-
ADC negative voltage reference. If the ADC is not used, tie
VREFN to VSS.
VDDA
40 53
84
-
-
Analog voltage supply. VDDAshould typically be the same
voltages as VDD but should be isolated to minimize noise
and error. VDDA should be tied to VDD if the ADC is not
used.
VDD
44, 58, 92,
8
10, 14,
34, 71,
59 54,
93
-
-
Supply voltage to the internal regulator and the external
rail.
LPC11U6x
Product data sheet
2
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
17 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
LQFP100
Symbol
Reset Type
state[1]
VBAT
47 63
99
-
-
Battery supply. Supplies power to the RTC. If no battery is
used, tie VBAT to VDD.
VSSA
41 54
85
-
-
Analog ground. VSSAshould typically be the same voltage
as VSS but should be isolated to minimize noise and error.
VSSA should be tied to VSS if the ADC is not used.
VSS
43, 57, 91,
2, 3, 7,
5
7
11,
53,
70
-
-
Ground.
[1]
LQFP48
LQFP64
Table 3.
Pin description
Pin functions are selected through the IOCON registers. See Table 2 for availability of USART3 and USART4 pin functions.
Description of pin functions
Pin state at reset for default function: I = Input; AI = Analog Input; O = Output; PU = internal pull-up enabled; IA = inactive, no
pull-up/down enabled;
F = floating; If the pins are not used, tie floating pins to ground or power to minimize power consumption.
[2]
Special analog pad.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as analog input, digital section of the pad is disabled and the pin is not 5 V tolerant; includes digital, programmable
filter.
[4]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as analog input, digital section of the pad is disabled and the pin is not 5 V tolerant; includes digital input glitch filter.
WAKEUP pin. The wake-up pin function can be disabled and the pin can be used for other purposes if the RTC is enabled for waking up
the part from Deep power-down mode.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis; includes
high-current output driver.
[6]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis.
[7]
I2C-bus pin compliant with the I2C-bus specification for I2C standard mode, I2C Fast-mode, and I2C Fast-mode Plus. The pin requires
an external pull-up to provide output functionality. When power is switched off, this pin is floating and does not disturb the I2C lines.
Open-drain configuration applies to all functions on this pin.
[8]
5 V tolerant pad. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to reset the chip and wake up
from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down mode.
[9]
Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode
only). This pad is not 5 V tolerant.
[10] 5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog crystal
oscillator connections. When configured for the crystal oscillator input/output, digital section of the pad is disabled and the pin is not 5 V
tolerant; includes digital, programmable filter.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
18 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8. Functional description
8.1 ARM Cortex-M0+ core
The ARM Cortex-M0+ core runs at an operating frequency of up to 50 MHz using a
two-stage pipeline. Integrated in the core are the NVIC and Serial Wire Debug with four
breakpoints and two watchpoints. The ARM Cortex-M0+ core supports a single-cycle I/O
enabled port for fast GPIO access.
The core includes a single-cycle multiplier and a system tick timer.
8.2 AHB multilayer matrix
The AHB multilayer matrix supports three masters, the M0+ core, the DMA, and the USB.
All masters can access all slaves (peripherals and memories).
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
19 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
TEST/DEBUG
INTERFACE
ARM
CORTEX-M0+
USB
DMA
masters
System
bus
slaves
FLASH
MAIN SRAM0
SRAM USB
SRAM1
ROM
EEPROM
SCTIMER0/PWM
SCTIMER1/PWM
HS GPIO
PINT/PATTERN MATCH
CRC
USB REGISTERS
DMA REGISTERS
AHB-TO-APB
BRIDGE
CT32B0
PMU
USART0
WWDT
I2C0
AHB MULTILAYER MATRIX
CT32B1
ADC
FLASHCTRL
USART4
SSP1
USART2
I2C1
SSP0
RTC
IOCON
GROUP0
USART3
CT16B0
CT16B1
DMA TRIGMUX
SYSCON
GROUP1
USART1
USART2
= master-slave connection
aaa-010774
Fig 7.
AHB multilayer matrix
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
20 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.3 On-chip flash programming memory
The LPC11U6x contain up to 256 KB on-chip flash program memory. The flash can be
programmed using In-System Programming (ISP) or In-Application Programming (IAP)
via the on-chip bootloader software.
The flash memory is divided into 24 x 4 KB and 5 x 32 KB sectors. Individual pages of
256 byte each can be erased using the IAP erase page command.
8.4 EEPROM
The LPC11U6x contain 4 KB of on-chip byte-erasable and byte-programmable EEPROM
data memory. The EEPROM can be programmed using In-Application Programming (IAP)
via the on-chip bootloader software.
8.5 SRAM
The LPC11U6x contain a total of up to 36 KB on-chip static RAM memory. The main
SRAM block contains either 8 KB, 16 KB, or 32 KB of main SRAM0. Two additional SRAM
blocks of 2 KB (SRAM1 and USB SRAM) are located in separate areas of the memory
map. See Figure 8.
8.6 On-chip ROM
The on-chip ROM contains the bootloader and the following Application Programming
Interfaces (APIs):
• In-System Programming (ISP) and In-Application Programming (IAP) support for flash
including IAP erase page command.
•
•
•
•
•
IAP support for EEPROM
USB API
Power profiles for configuring power consumption and PLL settings
32-bit integer division routines
APIs to use the following peripherals:
– I2C
– USART0 and USART1/2/3/4
– DMA
8.7 Memory mapping
The LPC11U6x incorporates several distinct memory regions, shown in the following
figures. Figure 8 shows the overall map of the entire address space from the user
program viewpoint following reset. The interrupt vector area supports address remapping.
The AHB (Advanced High-performance Bus) peripheral area is 2 MB in size and is divided
to allow for up to 128 peripherals. The APB (Advanced Peripheral Bus) peripheral area is
512 KB in size and is divided to allow for up to 32 peripherals. Each peripheral of either
type is allocated 16 KB of space. This addressing scheme allows simplifying the address
decoding for each peripheral.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
21 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
4 GB
LPC11U6x
0xFFFF FFFF
reserved
0xE010 0000
private peripheral bus
0xE000 0000
reserved
0xA000 8000
GPIO PINT
0xA000 4000
GPIO
0xA000 0000
APB peripherals
reserved
0x5001 0000
SCTIMER1/PWM
0x5000 E000
SCTIMER0/PWM
0x4007 8000
0x5000 C000
reserved
0x5000 8000
DMA
0x5000 4000
CRC
0x4008 4000
28
USART2
27
USART1
24
GPIO GROUP1 interrupt
23
GPIO GROUP0 interrupt
22
SSP1
0x4008 0000
APB peripherals
0x2000 4000
reserved
0x2000 0800
2 kB SRAM1
0x4007 0000
0x4006 C000
0x4006 4000
0x4006 0000
0x4005 C000
19
USART4
15
flash/EEPROM controller
14
PMU
0x4005 0000
0x4004 C000
18 system control (SYSCON) 0x4004 8000
IOCON
17
0x4004 4000
SSP0
16
0x4004 0000
0x2000 4800
2 kB USB SRAM
0x4007 4000
0x4005 8000
20 - 21 reserved
0x4000 0000
reserved
0.5 GB
USART3
25 - 26 reserved
reserved
1 GB
29
0x5000 0000
USB
0x4008 0000
30 - 31 reserved
0x2000 0000
reserved
0x4003 C000
0x4003 8000
11 - 13 reserved
0x4002 C000
0x1FFF 8000
32 kB boot ROM
10
DMA TRIGMUX
9
RTC
0x1400 1000
8
I2C1
0x4002 0000
0x1400 0000
7
12-bit ADC
0x4001 C000
6
32-bit counter/timer 1
0x4001 8000
0x1000 8000
5
32-bit counter/timer 0
0x4001 4000
0x1000 4000
4
16-bit counter/timer 1
0x4001 0000
3
16-bit counter/timer 0
0x4000 C000
2
USART0
0x4000 8000
1
0
WWDT
0x4000 4000
I2C0
0x4000 0000
0x1FFF 0000
reserved
4 kB MTB registers
reserved
32 kB MAIN SRAM0
16 kB MAIN SRAM0
reserved
0x1000 0000
0x0004 0000
256 kB on-chip flash (LPC11U68)
0x4002 8000
0x4002 4000
0x0002 0000
0x0000 00C0
128 kB on-chip flash (LPC11U67)
0x0000 0000
0 GB
Fig 8.
active interrupt vectors
0x0000 0000
aaa-010775
LPC11U6x Memory map
8.8 Nested Vectored Interrupt Controller (NVIC)
The Nested Vectored Interrupt Controller (NVIC) is part of the Cortex-M0+. The tight
coupling to the CPU allows for low interrupt latency and efficient processing of late arriving
interrupts.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
22 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.8.1 Features
• Controls system exceptions and peripheral interrupts.
• In the LPC11U6x, the NVIC supports vectored interrupts for each of the peripherals
and the eight pin interrupts. The following peripheral interrupts are ORed to contribute
to one interrupt in the NVIC:
– USART1, USART4
– USART2, USART3
– SCTimer0/PWM, SCTimer1/PWM
– BOD, WWDT
– ADC end-of-sequence A interrupt, threshold crossing interrupt
– ADC end-of-sequence B interrupt, overrun interrupt
– Flash, EEPROM
• Four programmable interrupt priority levels with hardware priority level masking.
• Software interrupt generation.
8.8.2 Interrupt sources
Each peripheral device has at least one interrupt line connected to the NVIC but can have
several interrupt flags. Individual interrupt flags can also represent more than one interrupt
source.
8.9 IOCON block
The IOCON block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Connect peripherals to the appropriate pins before activating the peripheral and before
enabling any related interrupt.
Enabling an analog function disables the digital pad. However, the internal pull-up and
pull-down resistors as well as the pin hysteresis must be disabled to obtain an accurate
reading of the analog input.
8.9.1 Features
• Programmable pin function.
• Programmable pull-up, pull-down, or repeater mode.
• All pins (except PIO0_4 and PIO0_5) are pulled up to 3.3 V (VDD = 3.3 V) if their
pull-up resistor is enabled.
• Programmable pseudo open-drain mode.
• Programmable (on/off) 10 ns glitch filter on pins PIO0_22, PIO0_23, PIO0_11 to
PIO0_16, PIO1_3, PIO1_9, PIO1_22, and PIO1_29. The glitch filter is turned on by
default.
• Programmable hysteresis.
• Programmable input inverter.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
23 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
• Digital filter with programmable filter constant on all pins. The minimum filter constant
is 1/50 MHz = 20 ns.
8.9.2 Standard I/O pad configuration
Figure 9 shows the possible pin modes for standard I/O pins with analog input function:
•
•
•
•
•
Digital output driver with configurable open-drain output
Digital input: Weak pull-up resistor (PMOS device) enabled/disabled
Digital input: Weak pull-down resistor (NMOS device) enabled/disabled
Digital input: Repeater mode enabled/disabled
Digital input: Input digital filter selectable on all pins. In addition, a 10 ns digital glitch
filter is selectable on pins with analog function.
• Analog input
VDD
VDD
open-drain enable
strong
pull-up
output enable
ESD
data output
PIN
pin configured
as digital output
driver
strong
pull-down
ESD
VSS
VDD
weak
pull-up
pull-up enable
weak
pull-down
repeater mode
enable
pull-down enable
PROGRAMMABLE
DIGITAL FILTER
data input
pin configured
as digital input
10 ns GLITCH
FILTER
select data
inverter
select glitch
filter
select analog input
analog input
pin configured
as analog input
Fig 9.
aaa-010776
Standard I/O pin configuration
8.10 Fast General-Purpose parallel I/O (GPIO)
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
24 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
LPC11U6x use accelerated GPIO functions:
• GPIO registers are on the ARM Cortex M0+ IO bus for fastest possible single-cycle
I/O timing, allowing GPIO toggling with rates of up to 25 MHz.
• An entire port value can be written in one instruction.
• Mask, set, and clear operations are supported for the entire port.
8.10.1 Features
• Bit level port registers allow a single instruction to set and clear any number of bits in
one write operation.
• Direction control of individual bits.
8.11 Pin interrupt/pattern match engine
The pin interrupt block configures up to eight pins from all digital pins for providing eight
external interrupts connected to the NVIC.
The pattern match engine can be used, in conjunction with software, to create complex
state machines based on pin inputs.
Any digital pin except pins PIO2_8 and PIO2_23 can be configured through the SYSCON
block as input to the pin interrupt or pattern match engine. The registers that control the
pin interrupt or pattern match engine are on the IO+ bus for fast single-cycle access.
8.11.1 Features
• Pin interrupts
– Up to eight pins can be selected from all digital pins except pins PIO2_8 and
PIO2_23 as edge- or level-sensitive interrupt requests. Each request creates a
separate interrupt in the NVIC.
– Edge-sensitive interrupt pins can interrupt on rising or falling edges or both.
– Level-sensitive interrupt pins can be HIGH- or LOW-active.
– Pin interrupts can wake up the part from sleep mode, deep-sleep mode, and
power-down mode.
• Pin interrupt pattern match engine
– Up to 8 pins can be selected from all digital pins except pins PIO2_8 and PIO2_23
to contribute to a boolean expression. The boolean expression consists of
specified levels and/or transitions on various combinations of these pins.
– Each minterm (product term) comprising the specified boolean expression can
generate its own, dedicated interrupt request.
– Any occurrence of a pattern match can be programmed to generate an RXEV
notification to the ARM CPU as well.
– The pattern match engine does not facilitate wake-up.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
25 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.12 GPIO group interrupts
The GPIO pins can be used in several ways to set pins as inputs or outputs and use the
inputs as combinations of level and edge sensitive interrupts. For each port/pin connected
to one of the two the GPIO Grouped Interrupt blocks (GINT0 and GINT1), the GPIO
grouped interrupt registers determine which pins are enabled to generate interrupts and w
the active polarities of each of those inputs.
The GPIO grouped interrupt registers also select whether the interrupt output is level or
edge triggered and whether it is based on the OR or the AND of all of the enabled inputs.
When the designated pattern is detected on the selected input pins, the GPIO grouped
interrupt block generates an interrupt. If the part is in a power-savings mode, it first
asynchronously wakes up the part prior to asserting the interrupt request. The interrupt
request line can be cleared by writing a one to the interrupt status bit in the control
register.
8.12.1 Features
• Two group interrupts are supported to reflect two distinct interrupt patterns.
• The inputs from any number of digital pins can be enabled to contribute to a combined
group interrupt.
• The polarity of each input enabled for the group interrupt can be configured HIGH or
LOW.
• Enabled interrupts can be logically combined through an OR or AND operation.
• The grouped interrupts can wake up the part from sleep, deep-sleep or power-down
modes.
8.13 DMA controller
The DMA controller can access all memories and the USART and SSP peripherals using
DMA requests. DMA transfers can also be triggered by internal events like the ADC
interrupts, timer match outputs, the pin interrupts (PINT0 and PINT1) and the SCTimer
DMA requests.
8.13.1 Features
• 16 channels with 14 channels connected to peripheral request inputs.
• DMA operations can be triggered by on-chip events or two pin interrupts. Each DMA
channel can select one trigger input from 12 sources.
•
•
•
•
•
•
LPC11U6x
Product data sheet
Priority is user selectable for each channel.
Continuous priority arbitration.
Address cache with two entries.
Efficient use of data bus.
Supports single transfers up to 1,024 words.
Address increment options allow packing and/or unpacking data.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
26 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.14 USB interface
The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a
host and one or more (up to 127) peripherals. The host controller allocates the USB
bandwidth to attached devices through a token-based protocol. The bus supports
hot-plugging and dynamic configuration of the devices. All transactions are initiated by the
host controller.
The USB interface consists of a full-speed device controller with on-chip PHY (PHYsical
layer) for device functions.
Remark: Configure the part in default power mode with the power profiles before using
the USB (see Section 8.25.7.1 “Power profiles”). Do not use the USB when the part runs
in performance, efficiency, or low-power mode.
8.14.1 Full-speed USB device controller
The device controller enables 12 Mbit/s data exchange with a USB Host controller. It
consists of a register interface, serial interface engine, and endpoint buffer memory. The
serial interface engine decodes the USB data stream and writes data to the appropriate
endpoint buffer. The status of a completed USB transfer or error condition is indicated via
status registers. An interrupt is also generated if enabled.
8.14.1.1
Features
•
•
•
•
•
•
Dedicated USB PLL available.
Fully compliant with USB 2.0 specification (full speed).
Supports 10 physical (5 logical) endpoints including one control endpoint.
Single and double buffering supported.
Each non-control endpoint supports bulk, interrupt, or isochronous endpoint types.
Supports wake-up from Deep-sleep mode and Power-down mode on USB activity
and remote wake-up.
• Supports SoftConnect functionality through internal pull-up resistor.
• Internal 33 Ω series termination resistors on USB_DP and USB_DM lines eliminate
the need for external series resistors.
• Supports Link Power Management (LPM).
• Supports XTAL-less low-speed mode using the 1% accurate IRC as the clock source
for the USB PLL. For board connection changes in low-speed mode, see Section
14.3.1 “USB Low-speed operation”.
8.15 USART0
Remark: The LPC11U6x contains two distinctive types of UART interfaces: USART0 is
software-compatible with the USART interface on the LPC11U1x/LPC11U2x/LPC11U3x
parts. USART1 to USART4 use a different register interface.
The USART0 includes full modem control, support for synchronous mode, and a smart
card interface. The RS-485/9-bit mode allows both software address detection and
automatic address detection using 9-bit mode.
The USART0 uses a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
27 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.15.1 Features
• Maximum USART0 data bit rate of 3.125 Mbit/s in asynchronous mode and 10 Mbit/s
in synchronous slave and master mode.
•
•
•
•
16 byte receive and transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
•
•
•
•
•
Support for RS-485/9-bit mode.
Support for modem control.
Support for synchronous mode.
Includes smart card interface.
DMA support.
8.16 USART1/2/3/4
Remark: The LPC11U6x contains two distinctive types of UART interfaces: USART0 is
software-compatible with the USART interface on the LPC11U1x/LPC11U2x/LPC11U3x
parts. USART1 to USART4 use a different register interface to achieve the same UART
functionality except for modem and smart card control.
Remark: USART3 and USART4 are available only on part LPC11U68JBD100.
Interrupts generated by the USART1/2/3/4 peripherals can wake up the part from
Deep-sleep and power-down modes if the USART is in synchronous mode, the 32 kHz
mode is enabled, or the CTS interrupt is enabled. This wake-up mechanism is not
available with the USART0 peripheral.
8.16.1 Features
• Maximum bit rates of 3.125 Mbit/s in asynchronous mode and 10 Mbit/s in
synchronous mode.
• 7, 8, or 9 data bits and 1 or 2 stop bits
• Synchronous mode with master or slave operation. Includes data phase selection and
continuous clock option.
• Multiprocessor/multidrop (9-bit) mode with software-address compare feature.
(RS-485 possible with software address detection and transceiver direction control.)
•
•
•
•
•
LPC11U6x
Product data sheet
RS-485 transceiver output enable.
Autobaud mode for automatic baud rate detection
Parity generation and checking: odd, even, or none.
One transmit and one receive data buffer.
RTS/CTS for hardware signaling for automatic flow control. Software flow control can
be performed using Delta CTS detect, Transmit Disable control, and any GPIO as an
RTS output.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
28 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
•
•
•
•
•
•
Received data and status can optionally be read from a single register
Break generation and detection.
Receive data is 2 of 3 sample "voting". Status flag set when one sample differs.
Built-in Baud Rate Generator with auto-baud function.
A fractional rate divider is shared among all USARTs.
Interrupts available for Receiver Ready, Transmitter Ready, Receiver Idle, change in
receiver break detect, Framing error, Parity error, Overrun, Underrun, Delta CTS
detect, and receiver sample noise detected.
• Loopback mode for testing of data and flow control.
• In synchronous slave mode, wakes up the part from deep-sleep and power-down
modes.
• Special operating mode allows operation at up to 9600 baud using the 32 kHz RTC
oscillator as the UART clock. This mode can be used while the device is in
Deep-sleep or Power-down mode and can wake up the device when a character is
received.
• USART transmit and receive functions work with the system DMA controller.
8.17 SSP serial I/O controller (SSP0/1)
The SSP controllers operate on a SSP, 4-wire SSI, or Microwire bus. The controller can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SSP supports full
duplex transfers, with frames of 4 bit to 16 bit of data flowing from the master to the slave
and from the slave to the master. In practice, often only one direction carries meaningful
data.
8.17.1 Features
• Maximum SSP speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
• Compatible with Motorola SPI (Serial Peripheral Interface), 4-wire Texas Instruments
SSI (Serial Synchronous Interface), and National Semiconductor Microwire buses
•
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
DMA support
8.18 I2C-bus serial I/O controller
The LPC11U6x contain two I2C-bus controllers.
The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock line
(SCL) and a Serial Data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C is a multi-master bus and can be
controlled by more than one bus master connected to it.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
29 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.18.1 Features
• One I2C-interface (I2C0) is an I2C-bus compliant interface with open-drain pins. The
I2C-bus interface supports Fast-mode Plus with bit rates up to 1 Mbit/s.
• One I2C-interface (I2C1) uses standard digital pins. The I2C-bus interface supports bit
rates up to 400 kbit/s.
•
•
•
•
•
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus can be used for test and diagnostic purposes.
• The I2C-bus controller supports multiple address recognition and a bus monitor mode.
8.19 Timer/PWM subsystem
Four standard timers and two state configurable timers can be combined to create
multiple PWM outputs using the match outputs and the match registers for each timer.
Each timer can create multiple PWM outputs with its own time base.
LPC11U6x
Product data sheet
Peripheral
Pin functions available for PWM
LQFP100
LQFP64
LQFP48
Match
registers
used
LQFP48
PWM
outputs
LQFP64
PWM resources
LQFP100
Table 4.
3
3
3
CT16B0
CT16B0_MAT0,
CT16B0_MAT1,
CT16B0_MAT2
CT16B0_MAT0,
CT16B0_MAT1,
CT16B0_MAT2
CT16B0_MAT0,
CT16B0_MAT1,
CT16B0_MAT2
4
2
2
2
CT16B1
CT16B1_MAT0,
CT16B1_MAT1
CT16B1_MAT0,
CT16B1_MAT1
CT16B1_MAT0,
CT16B1_MAT1
3
3
3
3
CT32B0
three of
CT32B0_MAT0,
CT32B0_MAT1,
CT32B0_MAT2,
CT32B0_MAT3
three of
CT32B0_MAT0,
CT32B0_MAT1,
CT32B0_MAT2,
CT32B0_MAT3
three of
CT32B0_MAT0,
CT32B0_MAT1,
CT32B0_MAT2,
CT32B0_MAT3
4
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
30 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 4.
PWM resources …continued
Pin functions available for PWM
LQFP64
LQFP48
LQFP48
LQFP100
Match
registers
used
LQFP64
Peripheral
LQFP100
PWM
outputs
3
3
3
CT32B1
three of
CT32B1_MAT0,
CT32B1_MAT1,
CT32B1_MAT2,
CT32B1_MAT3
three of
CT32B1_MAT0,
CT32B1_MAT1,
CT32B1_MAT2,
CT32B1_MAT3
three of
CT32B1_MAT0,
CT32B1_MAT1,
CT32B1_MAT2,
CT32B1_MAT3
4
4
4
3
SCTIMER0/
PWM
SCT0_OUT0,
SCT0_OUT1,
SCT0_OUT2,
SCT0_OUT3
SCT0_OUT0,
SCT0_OUT1,
SCT0_OUT2,
SCT0_OUT3
SCT0_OUT1,
SCT0_OUT2,
SCT0_OUT3
up to 5
4
2
-
SCTIMER1/
PWM
SCT1_OUT0,
SCT1_OUT1,
SCT1_OUT2,
SCT1_OUT3
SCT1_OUT2,
SCT1_OUT3
-
up to 5
The standard timers and the SCTimers combine to up to eight independent timers. Each
SCTimer can be configured either as one 32-bit timer or two independently counting 16-bit
timers which use the same input clock. The following combinations are possible:
Table 5.
Timer configurations
32-bit
timers
Resources
16-bit
timers
Resources
4
CT32B0, CT32B1, SCTimer0/PWM
as 32-bit timer, SCTimer1/PWM as
32-bit timer
2
CT16B0, CT16B1
2
CT32B0, CT32B1
6
CT16B0, CT16B1, SCTimer0/PWM
as two 16-bit timers,
SCTimer1/PWM as two 16-bit
timers
3
CT32B0, CT32B1, SCTimer0/PWM
as 32-bit timer (or SCTimer1/PWM
as 32-bit timer)
4
CT16B0, CT16B1, SCTimer1/PWM
as two 16-bit timers (or
SCTimer0/PWM as two 16-bit
timers)
8.19.1 State Configurable Timers (SCTimer0/PWM and SCTimer1/PWM)
The state configurable timer can create timed output signals such as PWM outputs
triggered by programmable events. Combinations of events can be used to define timer
states. The SCTimer/PWM can control the timer operations, capture inputs, change
states, and toggle outputs triggered only by events entirely without CPU intervention.
If multiple states are not implemented, the SCTimer/PWM simply operates as one 32-bit
or two 16-bit timers with match, capture, and PWM functions.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
31 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.19.1.1
Features
• Each SCTimer/PWM supports:
– 5 match/capture registers.
– 6 events.
– 8 states.
– 4 inputs and 4 outputs.
• Counter/timer features:
– Each SCTimer is configurable as two 16-bit counters or one 32-bit counter.
– Counters can be clocked by the system clock or selected input.
– Configurable as up counters or up-down counters.
– Configurable number of match and capture registers. Up to five match and capture
registers total.
– Upon match create the following events: interrupt; stop, limit, halt the timer or
change counting direction; toggle outputs.
– Counter value can be loaded into capture register triggered by a match or
input/output toggle.
• PWM features:
– Counters can be used with match registers to toggle outputs and create
time-proportioned PWM signals.
– Up to four single-edge or dual-edge PWM outputs with independent duty cycle and
common PWM cycle length.
• Event creation features:
– The following conditions define an event: a counter match condition, an input (or
output) condition such as a rising or falling edge or level, a combination of match
and/or input/output condition.
– Selected events can limit, halt, start, or stop a counter or change its direction.
– Events trigger state changes, output toggles, interrupts, and DMA transactions.
– Match register 0 can be used as an automatic limit.
– In bidirectional mode, events can be enabled based on the count direction.
– Match events can be held until another qualifying event occurs.
• State control features:
– A state is defined by events that can happen in the state while the counter is
running.
– A state changes into another state as a result of an event.
– Each event can be assigned to one or more states.
– State variable allows sequencing across multiple counter cycles.
• SCTimer match outputs (ORed with the general-purpose timer match outputs) serve
as ADC hardware trigger inputs.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
32 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.19.2 General purpose external event counter/timers (CT32B0/1 and CT16B0/1)
The LPC11U6x includes two 32-bit counter/timers and two 16-bit counter/timers. The
counter/timer is designed to count cycles of the system derived clock. It can optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. Each counter/timer also includes one capture input to trap the timer value
when an input signal transitions, optionally generating an interrupt.
8.19.2.1
Features
• A 32-bit/16-bit timer/counter with a programmable 32-bit/16-bit prescaler.
• Counter or timer operation.
• One capture channel per timer, that can take a snapshot of the timer value when an
input signal transitions. A capture event may also generate an interrupt.
• Four match registers per timer that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
• The timer and prescaler may be configured to be cleared on a designated capture
event. This feature permits easy pulse-width measurement by clearing the timer on
the leading edge of an input pulse and capturing the timer value on the trailing edge.
• PWM output function.
• Match outputs and capture inputs serve as hardware triggers for ADC conversions.
8.20 System tick timer (SysTick)
The ARM Cortex-M0+ includes a system tick timer (SYSTICK) that is intended to generate
a dedicated SYSTICK exception at a fixed time interval (typically 10 ms).
8.21 Windowed WatchDog Timer (WWDT)
The purpose of the WWDT is to prevent an unresponsive system state. If software fails to
update the watchdog within a programmable time window, the watchdog resets the
microcontroller
8.21.1 Features
• Internally resets chip if not periodically reloaded during the programmable time-out
period.
• Optional windowed operation requires reload to occur between a minimum and
maximum time period, both programmable.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
33 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
• Optional warning interrupt can be generated at a programmable time before watchdog
time-out.
• Software enables the WWDT, but a hardware reset or a watchdog reset/interrupt is
required to disable the WWDT.
•
•
•
•
Incorrect feed sequence causes reset or interrupt, if enabled.
Flag to indicate watchdog reset.
Programmable 24-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK)  256  4) to (Tcy(WDCLK)  224  4) in
multiples of Tcy(WDCLK)  4.
• The WatchDog Clock (WDCLK) source can be selected from the IRC or the dedicated
watchdog oscillator (WDOsc). The clock source selection provides a wide range of
potential timing choices of watchdog operation under different power conditions.
8.22 Real-Time Clock (RTC)
The RTC resides in a separate always-on voltage domain with battery back-up. The RTC
uses an independent oscillator, also located in the always-on voltage domain.
8.22.1 Features
• 32-bit, 1 Hz RTC counter and associated match register for alarm generation.
• Separate 16-bit high-resolution/wake-up timer clocked at 1 kHz for 1 ms resolution
with a more that one minute maximum time-out period.
• RTC alarm and high-resolution/wake-up timer time-out each generate independent
interrupt requests. Either time-out can wake up the part from any of the low-power
modes, including Deep power-down.
8.23 Analog-to-Digital Converter (ADC)
The ADC supports a resolution of 12 bit and fast conversion rates of up to 2 MSamples/s.
Sequences of analog-to-digital conversions can be triggered by multiple sources. Possible
trigger sources are the counter/timer match outputs and capture inputs and the ARM
TXEV.
The ADC includes a hardware threshold compare function with zero-crossing detection.
8.23.1 Features
• 12-bit successive approximation analog to digital converter.
• 12-bit conversion rate of up to 2 MSamples/s.
• Temperature sensor voltage output selectable as internal voltage source for
channel 0.
•
•
•
•
Two configurable conversion sequences with independent triggers.
Optional automatic high/low threshold comparison and zero-crossing detection.
Power-down mode and low-power operating mode.
Measurement range VREFN to VREFP (typically 3 V; not to exceed VDDA voltage
level).
• Burst conversion mode for single or multiple inputs.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
34 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.24 Temperature sensor
The temperature sensor transducer uses an intrinsic pn-junction diode reference and
outputs a CTAT voltage (Complement To Absolute Temperature). The output voltage
varies inversely with device temperature with an absolute accuracy of better than ±5 C
over the full temperature range (40 C to +105 C) for typical samples. The temperature
sensor is approximately linear with a slight curvature. The output voltage is measured
over different ranges of temperatures and fit with linear-least-square lines.
After power-up and after switching the input channels of the ADC, the temperature sensor
output must be allowed to settle to its stable value before it can be used as an accurate
ADC input.
For an accurate measurement of the temperature sensor by the ADC, the ADC must be
configured in single-channel burst mode. The last value of a nine-conversion (or more)
burst provides an accurate result.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
35 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.25 Clocking and power control
8.25.1 Clock generation
CPU,
system control,
PMU
SYSTEM CLOCK
DIVIDER
system clock
n
memories,
peripheral clocks
SYSAHBCLKCTRL
(AHB clock enable)
main
clock
IRC
SSP0 PERIPHERAL
CLOCK DIVIDER
SSP0
watchdog oscillator
USART0 PERIPHERAL
CLOCK DIVIDER
MAINCLKSEL
(main clock select)
RTC
oscillator,
32 kHz
output
SSP1 PERIPHERAL
CLOCK DIVIDER
IRC
system
oscillator
RTCOSCCTRL
(RTC osc enable)
USART0
SSP1
SYSTEM PLL
FRACTIONAL RATE
GENERATOR
CLOCK DIVIDER
FRGCLKDIV
USART1
USART2
USART3
USART4
SYSPLLCLKSEL
(system PLL clock select)
7
CLOCK DIVIDER
IOCONCLKDIV
IOCON
glitch filter
IRC
system
oscillator
USBPLLCLKSEL
(USB clock select)
USB PLL
USB 48 MHz CLOCK
DIVIDER
USB
CLKOUT PIN CLOCK
DIVIDER
CLKOUT pin
USBCLKSEL
(USB clock select)
IRC oscillator
system oscillator
watchdog oscillator
CLKOUTSEL
(CLKOUT clock select)
IRC oscillator
WDT
watchdog oscillator
WDCLKSEL
(WDT clock select)
aaa-010817
Fig 10. Clock generation
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
36 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.25.2 Power domains
The LPC11U6x provide two independent power domains that allow the bulk of the device
to have power removed while maintaining operation of the RTC and the backup registers.
The VBAT pin supplies power only to the RTC domain. The RTC requires a minimum of
power to operate, which can be supplied by an external battery. The device core power
(VDD) is used to operate the RTC whenever VDD is present. Therefore, there is no power
drain from the RTC battery when VDD is available and VDD  VBAT + 0.3 V.
LPC11U6x
to I/O pads
to core
VSS
REGULATOR
to memories,
peripherals,
oscillators,
PLLs
VDD
MAIN POWER DOMAIN
WAKEUP
ULTRA LOW-POWER
REGULATOR
VBAT
WAKE-UP
CONTROL
BACKUP REGISTERS
RTCXIN
32 kHz
OSCILLATOR
RTCXOUT
REAL-TIME CLOCK
ALWAYS-ON/RTC POWER DOMAIN
ADC
TEMP SENSE
VDDA
VDD
ADC POWER DOMAIN
VSSA
aaa-010818
Fig 11. Power distribution
8.25.3 Integrated oscillators
The LPC11U6x include the following independent oscillators: the system oscillator, the
Internal RC oscillator (IRC), the watchdog oscillator, and the 32 kHz RTC oscillator. Each
oscillator can be used for more than one purpose as required in a particular application.
Following reset, the LPC11U6x operates from the internal RC oscillator until software
switches to a different clock source. The IRC allows the system to operate without any
external crystal and the bootloader code to operate at a known frequency.
See Figure 10 for an overview of the LPC11U6x clock generation.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
37 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.25.3.1
Internal RC oscillator
The IRC can be used as the clock source for the WDT, the USB PLL in low-speed USB
applications, or as the clock that drives the system PLL and then the CPU. The nominal
IRC frequency is 12 MHz.
Upon power-up, any chip reset, or wake-up from Deep power-down mode, the LPC11U6x
use the IRC as the clock source. Software can later switch to one of the other available
clock sources.
8.25.3.2
System oscillator
The system oscillator can be used as the clock source for the CPU, with or without using
the PLL. Use the system oscillator to provide the clock source to USB.
The system oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the
system PLL.
The system oscillator has a wake-up time of approximately 500 μs.
8.25.3.3
WatchDog oscillator
The watchdog oscillator can be used as a clock source that directly drives the CPU, the
watchdog timer, or the CLKOUT pin. The watchdog oscillator nominal frequency is
programmable between 9.4 kHz and 2.3 MHz. The frequency spread over processing and
temperature is 40 % (see also Table 14).
8.25.3.4
RTC oscillator
The low-power RTC oscillator provides a 1 Hz clock and a 1 kHz clock to the RTC and a
32 kHz clock output that can be used to obtain the main clock (see Figure 10).
8.25.4 System PLL and USB PLL
The LPC11U6x contain a system PLL and a dedicated PLL for generating the 48 MHz
USB clock. The system and USB PLLs are identical.
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz. To support this frequency range, an additional divider keeps the
CCO within its frequency range while the PLL is providing the desired output frequency.
The output divider can be set to divide by 2, 4, 8, or 16 to produce the output clock. The
PLL output frequency must be lower than 100 MHz. Since the minimum output divider
value is 2, it is insured that the PLL output has a 50 % duty cycle. The PLL is turned off
and bypassed following a chip reset. Software can enable the PLL later. The program
must configure and activate the PLL, wait for the PLL to lock, and then connect to the PLL
as a clock source. The PLL settling time is 100 s.
8.25.5 Clock output
The LPC11U6x feature a clock output function that routes the IRC oscillator, the system
oscillator, the watchdog oscillator, or the main clock to an output pin.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
38 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.25.6 Wake-up process
The LPC11U6x begin operation by using the 12 MHz IRC oscillator as the clock source at
power-up and when awakened from Deep power-down mode. This mechanism allows
chip operation to resume quickly. If the application uses the main oscillator or the PLL,
software must enable these components and wait for them to stabilize. Only then can the
system use the PLL and main oscillator as a clock source.
8.25.7 Power control
The LPC11U6x support various power control features. There are four special modes of
processor power reduction: Sleep mode, Deep-sleep mode, Power-down mode, and
Deep power-down mode. The CPU clock rate can also be controlled as needed by
changing clock sources, reconfiguring PLL values, and/or altering the CPU clock divider
value. This power control mechanism allows a trade-off of power versus processing speed
based on application requirements. In addition, a register is provided for shutting down the
clocks to individual on-chip peripherals. This register allows fine-tuning of power
consumption by eliminating all dynamic power use in any peripherals that are not required
for the application. Selected peripherals have their own clock divider which provides even
better power control.
8.25.7.1
Power profiles
The power consumption in Active and Sleep modes can be optimized for the application
through simple calls to the power profile. The power configuration routine configures the
LPC11U6x for one of the following power modes:
• Default mode corresponding to power configuration after reset.
• CPU performance mode corresponding to optimized processing capability.
• Efficiency mode corresponding to optimized balance of current consumption and CPU
performance.
• Low-current mode corresponding to lowest power consumption.
In addition, the power profile includes routines to select the optimal PLL settings for a
given system clock and PLL input clock.
Remark: When using the USB, configure the LPC11U6x in Default mode.
8.25.7.2
Sleep mode
When Sleep mode is entered, the clock to the core is stopped. Resumption from the Sleep
mode does not need any special sequence but re-enabling the clock to the ARM core.
In Sleep mode, execution of instructions is suspended until either a reset or interrupt
occurs. Peripheral functions continue operation during Sleep mode and can generate
interrupts to cause the processor to resume execution. Sleep mode eliminates dynamic
power used by the processor itself, by memory systems and related controllers, and by
internal buses.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
39 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.25.7.3
Deep-sleep mode
In Deep-sleep mode, the LPC11U6x core is in Sleep mode and all peripheral clocks and
all clock sources are off except for the IRC. The IRC output is disabled unless the IRC is
selected as input to the watchdog timer. In addition, all analog blocks are shut down and
the flash is in standby mode. In Deep-sleep mode, the application can keep the watchdog
oscillator and the BOD circuit running for self-timed wake-up and BOD protection.
The LPC11U6x can wake up from Deep-sleep mode via reset, selected GPIO pins, a
watchdog timer interrupt, an interrupt generating USB port activity, an RTC interrupt, or
any interrupts that the USART1 to USART4 interfaces can create in Deep-sleep mode.
The USART wake-up requires the 32 kHz mode, the synchronous mode, or the CTS
interrupt to be set up.
Deep-sleep mode saves power and allows for short wake-up times.
8.25.7.4
Power-down mode
In Power-down mode, the LPC11U6x is in Sleep mode and all peripheral clocks and all
clock sources are off except for watchdog oscillator if selected. In addition, all analog
blocks and the flash are shut down. In Power-down mode, the application can keep the
BOD circuit running for BOD protection.
The LPC11U6x can wake up from Power-down mode via reset, selected GPIO pins, a
watchdog timer interrupt, an interrupt generating USB port activity, an RTC interrupt, or
any interrupts that the USART1 to USART4 interfaces can create in Power-down mode.
The USART wake-up requires the 32 kHz mode, the synchronous mode, or the CTS
interrupt to be set up.
Power-down mode reduces power consumption compared to Deep-sleep mode at the
expense of longer wake-up times.
8.25.7.5
Deep power-down mode
In Deep power-down mode, power is shut off to the entire chip except for the WAKEUP
pin and the always-on RTC power domain. The LPC11U6x can wake up from Deep
power-down mode via the WAKEUP pin or a wake-up signal generated by the RTC
interrupt.
The LPC11U6x can be blocked from entering Deep power-down mode by setting a lock bit
in the PMU block. Blocking the Deep power-down mode enables the application to keep
the watchdog timer or the BOD running at all times.
If the WAKEUP pin is used in the application, an external pull-up resistor is required on
the WAKEUP pin to hold it HIGH while the part is in deep power-down mode. To wake up
from deep power-down mode, pull the WAKEUP pin LOW. In addition, pull the RESET pin
HIGH to prevent it from floating while in Deep power-down mode.
8.26 System control
8.26.1 Reset
Reset has four sources on the LPC11U6x: the RESET pin, the WatchDog reset, power-on
reset (POR), and the BrownOut Detection (BOD) circuit. The RESET pin is a Schmitt
trigger input pin. Assertion of chip reset by any source, once the operating voltage attains
a usable level, starts the IRC and initializes the flash controller.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
40 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the boot block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values. The internal reset
status is reflected on the RSTOUT pin.
In Deep power-down mode, an external pull-up resistor is required on the RESET pin.
The RESET pin is operational in active, sleep, deep-sleep, and power-down modes if the
RESET function is selected in the IOCON register for pin PIO0_0 (this is the default). A
LOW-going pulse as short as 50 ns executes the reset and also wakes up the part if in
sleep, deep-sleep or power-down mode. The RESET pin is not functional in Deep
power-down mode.
9''
9''
9''
5SX
UHVHW
(6'
QV5&
*/,7&+),/7(5
3,1
(6'
966
DDD
Fig 12. RESET pin configuration
8.26.2 Brownout detection
The LPC11U6x includes two levels for monitoring the voltage on the VDD pin. If this
voltage falls below one of the selected levels, the BOD asserts an interrupt signal to the
NVIC. This signal can be enabled for interrupt in the Interrupt Enable Register in the NVIC
to cause a CPU interrupt. Alternatively, software can monitor the signal by reading a
dedicated status register. Two threshold levels can be selected to cause a forced reset of
the chip.
8.26.3 Code security (Code Read Protection - CRP)
CRP provides different levels of security in the system so that access to the on-chip flash
and use of the Serial Wire Debugger (SWD) and In-System Programming (ISP) can be
restricted. Programming a specific pattern into a dedicated flash location invokes CRP.
IAP commands are not affected by the CRP.
In addition, ISP entry via the PIO0_1 pin can be disabled without enabling CRP. For
details, see the LPC11Uxx user manual.
There are three levels of Code Read Protection:
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
41 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
1. CRP1 disables access to the chip via the SWD and allows partial flash update
(excluding flash sector 0) using a limited set of the ISP commands. This mode is
useful when CRP is required and flash field updates are needed but all sectors cannot
be erased.
2. CRP2 disables access to the chip via the SWD and only allows full flash erase and
update using a reduced set of the ISP commands.
3. Running an application with level CRP3 selected, fully disables any access to the chip
via the SWD pins and the ISP. This mode effectively disables ISP override using
PIO0_1 pin as well. If necessary, the application must provide a flash update
mechanism using IAP calls or using a call to the reinvoke ISP command to enable
flash update via the USART.
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
In addition to the three CRP levels, sampling of pin PIO0_1 for valid user code can be
disabled. For details, see the LPC11U6x user manual.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
42 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
8.27 Emulation and debugging
Debug functions are integrated into the ARM Cortex-M0+. Serial wire debug functions are
supported in addition to a standard JTAG boundary scan. The ARM Cortex-M0+ is
configured to support up to four breakpoints and two watch points.
The RESET pin selects between the JTAG boundary scan (RESET = LOW) and the ARM
SWD debug (RESET = HIGH). The ARM SWD debug port is disabled while the
LPC11U6x is in reset.
To perform boundary scan testing, follow these steps:
1. Erase any user code residing in flash.
2. Power up the part with the RESET pin pulled HIGH externally.
3. Wait for at least 250 s.
4. Pull the RESET pin LOW externally.
5. Perform boundary scan operations.
6. Once the boundary scan operations are completed, assert the TRST pin to enable the
SWD debug mode, and release the RESET pin (pull HIGH).
Remark: The JTAG interface cannot be used for debug purposes.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
43 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
9. Limiting values
Table 6.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
VDD
supply voltage
VDDA
analog supply voltage
Vref
reference voltage
VBAT
battery supply voltage
Conditions
[2]
on pin VREFP
input voltage
VI
5 V tolerant I/O
pins; only valid
when the VDD(IO)
supply voltage is
present
Max
Unit
0.5
4.6
V
0.5
4.6
V
0.5
4.6
V
0.5
4.6
V
[3][4]
0.5
+5.5
V
[5]
0.5
+5.5
V
0.5
VDD + 0.5
V
0.5
4.6
V
[2]
0.5
+2.5
V
[2]
on open-drain
I2C-bus pins
PIO0_4 and
PIO0_5
USB_DM,
USB_DP pins
[6]
analog input voltage
VIA
Min
[7]
Vi(xtal)
crystal input voltage
Vi(rtcx)
32 kHz oscillator input voltage
0.5
4.6
V
IDD
supply current
per supply pin
-
100
mA
ISS
ground current
per ground pin
-
100
mA
Ilatch
I/O latch-up current
(0.5 VDD(IO)) < VI
< (1.5 VDD(IO));
-
100
mA
65
+150
C
-
150
C
-
1.5
W
-
3
kV
pins configured for
XTALIN and
XTALOUT
Tj < 125 C
Tstg
storage temperature
[8]
Tj(max)
maximum junction temperature
Ptot(pack)
total power dissipation (per package)
based on package
heat transfer, not
device power
consumption
Vesd
electrostatic discharge voltage
human body
model; all pins
[1]
[9]
The following applies to the limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Maximum/minimum voltage above the maximum operating voltage (see Table 8) and below ground that can be applied for a short time
(< 10 ms) to a device without leading to irrecoverable failure. Failure includes the loss of reliability and shorter lifetime of the device.
[3]
Applies to all 5 V tolerant I/O pins except true open-drain pins PIO0_4 and PIO0_5.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
44 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
[4]
Including the voltage on outputs in 3-state mode.
[5]
VDD(IO) present or not present. Compliant with the I2C-bus standard. 5.5 V can be applied to this pin when VDD(IO) is powered down.
[6]
An ADC input voltage above 3.6 V can be applied for a short time without leading to immediate, unrecoverable failure. Accumulated
exposure to elevated voltages at 4.6 V must be less than 106 s total over the lifetime of the device. Applying an elevated voltage to the
ADC inputs for a long time affects the reliability of the device and reduces its lifetime.
[7]
It is recommended to connect an overvoltage protection diode between the analog input pin and the voltage supply pin.
[8]
Dependent on package type.
[9]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
10. Thermal characteristics
The average chip junction temperature, Tj (C), can be calculated using the following
equation:
T j = T amb +  P D  R th  j – a  
(1)
• Tamb = ambient temperature (C),
• Rth(j-a) = the package junction-to-ambient thermal resistance (C/W)
• PD = sum of internal and I/O power dissipation
The internal power dissipation is the product of IDD and VDD. The I/O power dissipation of
the I/O pins is often small and many times can be negligible. However it can be significant
in some applications.
Table 7.
Symbol
Thermal resistance value (C/W): ±15 %
Parameter
Conditions
Typ
Unit
thermal resistance
junction-to-ambient
JEDEC (4.5 in  4 in)
0 m/s
67
C/W
1 m/s
58
C/W
2.5 m/s
53
C/W
0 m/s
100
C/W
1 m/s
79
C/W
LQFP48
ja
8-layer (4.5 in  3 in)
71
C/W
jc
thermal resistance junction-to-case
15
C/W
jb
thermal resistance junction-to-board
19
C/W
2.5 m/s
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
45 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 7.
Symbol
Thermal resistance value (C/W): ±15 %
Parameter
Conditions
Typ
Unit
thermal resistance
junction-to-ambient
JEDEC (4.5 in  4 in)
0 m/s
58
C/W
1 m/s
51
C/W
2.5 m/s
47
C/W
0 m/s
81
C/W
1 m/s
66
C/W
2.5 m/s
60
C/W
LQFP64
ja
8-layer (4.5 in  3 in)
jc
thermal resistance junction-to-case
18
C/W
jb
thermal resistance junction-to-board
23
C/W
0 m/s
49
C/W
1 m/s
44
C/W
2.5 m/s
41
C/W
0 m/s
66
C/W
1 m/s
55
C/W
2.5 m/s
51
C/W
LQFP100
ja
thermal resistance
junction-to-ambient
JEDEC (4.5 in  4 in)
8-layer (4.5 in  3 in)
jc
thermal resistance junction-to-case
18
C/W
jb
thermal resistance junction-to-board
24
C/W
11. Static characteristics
Table 8.
Static characteristics
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
VDD
supply voltage (core
and external rail)
VDDA
analog supply voltage
Vref
reference voltage
VBAT
battery supply voltage
LPC11U6x
Product data sheet
Conditions
[2]
on pin VREFP
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
Min
Typ[1] Max
Unit
2.4
3.3
3.6
V
2.4
3.3
3.6
V
2.4
-
VDDA
V
2.4
3.3
3.6
V
© NXP Semiconductors N.V. 2014. All rights reserved.
46 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 8.
Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Conditions
IDD
supply current
Active mode; code
Min
Typ[1] Max
Unit
-
2.3
-
mA
-
1.5
-
mA
-
7.8
-
mA
-
6.4
-
mA
-
1.2
-
mA
-
0.8
-
mA
-
3.3
-
mA
-
2.8
-
mA
-
275
350
A
-
-
640
A
-
5
22
A
-
-
130
A
-
1.2
5
A
-
-
14
-
550
-
nA
-
0
-
-
-
0
-
-
-
1.2
-
A
-
0.5
10
nA
while(1){}
executed from flash
IDD
IDD
supply current
supply current
system clock = 12 MHz; default
mode; VDD = 3.3 V
[3][4][5]
system clock = 12 MHz;
low-current mode; VDD = 3.3 V
[3][4][5]
system clock = 50 MHz; default
mode; VDD = 3.3 V
[3][4][7]
system clock = 50 MHz;
low-current mode; VDD = 3.3 V
[3][4][7]
[7][8]
[7][8]
[8][10]
[8][10]
Sleep mode;
system clock = 12 MHz; default
mode; VDD = 3.3 V
[3][4][5]
system clock = 12 MHz;
low-current mode; VDD = 3.3 V
[3][4][5]
system clock = 50 MHz; default
mode; VDD = 3.3 V
[3][4][10]
system clock = 50 MHz;
low-current mode; VDD = 3.3 V
[3][4][10]
Deep-sleep mode;
VDD = 3.3 V;
[7][8]
[7][8]
[7][8]
[7][8]
[3][4][11]
Tamb = 25 C
Tamb = 105 C
IDD
supply current
Power-down mode;
VDD = 3.3 V
[3][4][11]
Tamb = 25 C
Tamb = 105 C
IDD
supply current
Deep power-down mode; VDD =
3.3 V; VBAT = 0 or VBAT = 3.0 V
[3][12]
RTC oscillator running
Tamb = 25 C
Tamb = 105 C
RTC oscillator input grounded
IBAT
battery supply current
[3][12]
Deep power-down mode; VDD =
VDDA = 3.3 V; VBAT = 3.0 V;
RTC oscillator running
RTC off
IBAT
battery supply current
VDD = VDDA = 0 V; VBAT = 3.0 V
RTC oscillator running
Standard port pins configured as digital pins, RESET; see Figure 13
IIL
LOW-level input current VI = 0 V; on-chip pull-up resistor
disabled
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
47 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 8.
Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1] Max
Unit
IIH
HIGH-level input
current
VI = VDD; on-chip pull-down
resistor disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD; on-chip
pull-up/down resistors disabled
-
0.5
10
nA
VI
input voltage
VDD  2.4 V; 5 V tolerant pins
0
-
5
V
[14]
[15]
VO
output voltage
VIH
HIGH-level input
voltage
VDD = 0 V
0
-
3.6
V
output active
0
-
VDD
V
0.7 VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3 VDD
V
Vhys
hysteresis voltage
0.05 VDD
-
-
V
VOH
HIGH-level output
voltage
IOH = 4 mA
VDD  0.4 -
-
V
VOL
LOW-level output
voltage
IOL = 4 mA
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD  0.4 V;
4
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
4
-
-
mA
IOHS
HIGH-level short-circuit VOH = 0 V
output current
[16]
-
-
45
mA
IOLS
LOW-level short-circuit
output current
VOL = VDD
[16]
-
-
50
mA
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V;
10
50
85
A
0
0
0
A
2.4 V  VDD  3.6 V
VDD < VI < 5 V
High-drive output pins configured as digital pin (PIO0_7 and PIO1_31); see Figure 13
IIL
LOW-level input current VI = 0 V; on-chip pull-up resistor
disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip pull-down
resistor disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD; on-chip
pull-up/down resistors disabled
-
0.5
10
nA
VI
input voltage
VDD  2.4 V
0
-
5
V
[14]
[15]
VDD = 0 V
0
-
3.6
V
output active
0
-
VDD
V
0.7 VDD
-
-
V
LOW-level input voltage
-
-
0.3 VDD
V
hysteresis voltage
0.05 VDD
-
-
V
VO
output voltage
VIH
HIGH-level input
voltage
VIL
Vhys
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
48 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 8.
Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Typ[1] Max
Symbol
Parameter
Conditions
Min
Unit
VOH
HIGH-level output
voltage
IOH = 12 mA; 2.4 V  VDD  2.5 V
VDD  0.4 -
-
V
IOH = 20 mA; 2.5 V  VDD  3.6 V
VDD  0.4 -
-
V
VOL
LOW-level output
voltage
IOL = 4 mA
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD  0.4 V;
2.4 V  VDD  2.5 V
12
-
-
mA
VOH = VDD  0.4 V;
2.5 V  VDD  3.6 V
20
-
-
mA
VOL = 0.4 V
4
-
-
mA
IOL
LOW-level output
current
IOHS
HIGH-level short-circuit VOH = 0 V
output current
[16]
-
-
45
mA
IOLS
LOW-level short-circuit
output current
VOL = VDD
[16]
-
-
50
mA
Ipd
pull-down current
VI = 5 V
[17]
10
50
150
A
Ipu
pull-up current
VI = 0 V
[17]
10
50
85
A
0
0
0
A
VDD < VI < 5 V
I2C-bus
pins (PIO0_4 and PIO0_5); see Figure 13
VIH
HIGH-level input
voltage
0.7 VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3 VDD
V
Vhys
hysteresis voltage
0.05 VDD
-
-
V
I2C-bus
IOL
LOW-level output
current
VOL = 0.4 V;
pins
configured as standard mode pins
3.5
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V; I2C-bus pins
configured as Fast-mode Plus
pins
20
-
-
mA
ILI
input leakage current
VI = VDD
-
2
4
A
-
10
22
A
[18]
VI = 5 V
USB_DM and USB_DP pins
[2]
VI
input voltage
0
-
VDD
V
VIH
HIGH-level input
voltage
1.5
-
-
V
VIL
LOW-level input voltage
-
-
1.3
V
Vhys
hysteresis voltage
0.32
-
-
V
Zout
output impedance
28
-
44
Ω
VOH
HIGH-level output
voltage
With 15 kΩ resistor to ground
2.9
-
-
V
VOL
LOW-level output
voltage
With internal 1.5 kΩ resistor to
3.6 V pull-up enabled
-
-
0.18
V
IOH
HIGH-level output
current
VOH = VDD  0.3 V
[19]
4.8
-
-
mA
IOL
LOW-level output
current
VOL = 0.3 V
[19]
5.0
-
-
mA
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
49 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 8.
Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1] Max
Unit
IOLS
LOW-level short-circuit
output current
drive LOW; pad connected to
ground
-
-
125
mA
IOHS
HIGH-level short-circuit drive HIGH; pad connected to
output current
ground
-
-
125
mA
0.5
1.8
1.95
V
Oscillator pins
Vi(xtal)
crystal input voltage
Vo(xtal)
crystal output voltage
Vi(rtcx)
32 kHz oscillator input
voltage
Vo(rtcx)
32 kHz oscillator output on pin RTCXOUT
voltage
0.5
1.8
1.95
V
[20]
0.5
-
3.6
V
[20]
0.5
-
3.6
V
pins with analog and digital
functions
[21]
-
-
7.1
pF
I2C-bus pins (PIO0_4 and
PIO0_5)
[21]
-
-
2.5
pF
pins with digital functions only
[21]
-
-
2.8
pF
on pin RTCXIN
Pin capacitance
input/output
capacitance
Cio
[1]
Typical ratings are not guaranteed. The values listed are for room temperature (25 C), nominal supply voltages.
[2]
For USB operation: 3.0 VVDD  3.6 V.
[3]
Tamb = 25 C.
[4]
IDD measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
[5]
IRC enabled; system oscillator disabled; system PLL disabled.
[6]
System oscillator enabled; IRC disabled; system PLL disabled.
[7]
BOD disabled.
[8]
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to USART, CLKOUT, and IOCON disabled in system
configuration block.
[9]
IRC enabled; system oscillator disabled; system PLL enabled.
[10] IRC disabled; system oscillator enabled; system PLL enabled.
[11] All oscillators and analog blocks turned off.
[12] WAKEUP pin pulled HIGH externally.
[13] Low-current mode PWR_LOW_CURRENT selected when running the set_power routine in the power profiles.
[14] Including voltage on outputs in tri-state mode.
[15] Tri-state outputs go into tri-state mode in Deep power-down mode.
[16] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[17] Pull-up and pull-down currents are measured across the weak internal pull-up/pull-down resistors. See Figure 13.
[18] To VSS.
[19] The parameter values specified are simulated and absolute values.
[20] The input voltage of the RTC oscillator is limited as follows: Vi(rtcx), Vo(rtcx) < max(VBAT, VDD).
[21] Including bonding pad capacitance.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
50 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
VDD
IOL
Ipd
pin PIO0_n
+
A
IOH
Ipu
pin PIO0_n
-
+
A
aaa-010819
Fig 13. Pin input/output current measurement
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
51 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
11.1 Power consumption
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions:
• Configure all pins as GPIO with pull-up resistor disabled in the IOCON block.
• Configure GPIO pins as outputs using the GPIO DIR register.
• Write 1 to the GPIO CLR register to drive the outputs LOW.
DDD
,''
P$
0+]
0+]
0+]
0+]
0+]
0+]
9''9
Conditions: Tamb = 25 C; active mode entered executing code while(1){} from flash; all
peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F), all peripheral
clocks disabled; internal pull-up resistors disabled; BOD disabled; low-current mode.
1 MHz to 6 MHz: IRC enabled; PLL disabled.
12 MHz: IRC enabled; PLL disabled.
24 MHz to 50 MHz: IRC disabled; PLL enabled; sysosc enabled.
Fig 14. Active mode: Typical supply current IDD versus supply voltage VDD
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
52 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
DDD
,''
P$
0+]
0+]
0+]
0+]
0+]
0+]
WHPSHUDWXUHƒ&
Conditions: VDD = 3.3 V; active mode entered executing code while(1){} from flash; all
peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F; all peripheral
clocks disabled; internal pull-up resistors disabled; BOD disabled; low-current mode.
1 MHz to 6 MHz: IRC enabled; PLL disabled.
12 MHz: IRC enabled; PLL disabled.
24 MHz to 50 MHz: IRC disabled; PLL enabled; sysosc enabled.
Fig 15. Active mode: Typical supply current IDD versus temperature
DDD
0+]
P$
0+]
0+]
0+]
0+]
0+]
0+]
ƒ&
Conditions: VDD = 3.3 V; sleep mode entered from flash; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F) all peripheral clocks disabled; internal
pull-up resistors disabled; BOD disabled; low-current mode.
1 MHz to 6 MHz: IRC enabled; PLL disabled.
12 MHz: IRC enabled; PLL disabled.
24 MHz to 48 MHz: IRC disabled; PLL enabled; sysosc enabled.
Fig 16. Sleep mode: Typical supply current IDD versus temperature for different system
clock frequencies
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
53 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
DDD
,''
ȝ$
9
9
9
9
9
7ƒ&
Conditions: BOD disabled; all oscillators and analog blocks disabled
Fig 17. Deep-sleep mode: Typical supply current IDD versus temperature for different
supply voltages VDD
DDD
,''
ȝ$
7ƒ&
Conditions: BOD disabled; all oscillators and analog blocks disabled; VDD = 2.4 V to 3.6 V.
Fig 18. Power-down mode: Typical supply current IDD versus temperature for different
supply voltages VDD
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
54 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
DDD
,''
ȝ$
9
9
9
9
9
7ƒ&
Conditions: RTC running; VBAT = 0 V
Fig 19. Deep power-down mode: Typical supply current IDD versus temperature for
different supply voltages VDD
DDD
,%$7
ȝ$
7ƒ&
Conditions: RTC not running; VBAT = 3.0 V; VDD floating.
Fig 20. Deep power-down mode: Typical battery supply current IBAT versus temperature
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
55 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
11.2 CoreMark data
aaa-011173
2.5
CM
(((iterations/s)/MHz))
2.25
cpu performance
efficiency
default/low-current
2
aaa-011174
2.5
CM
(((iterations/s)/MHz))
2.25
cpu performance
efficiency
default/low-current
2
1.75
1.75
1.5
1.5
1.25
1.25
1
1
0
10
20
30
40
system clock frequency (MHz)
50
Measured with Keil uVision v.4.72.
0
10
20
30
40
system clock frequency (MHz)
50
Measured with Keil uVision v.4.60.
Conditions: Conditions: VDD = 3.3 V; active mode; all peripherals except one UART and the SCTimer disabled in the
SYSAHBCLKCTRL register; internal pull-up resistors enabled; BOD disabled.
Fig 21. CoreMark score for different power mode settings of the power profiles
aaa-011175
15
IDD
(mA)
12.5
10
10
7.5
7.5
cpu performance
default
efficiency
low-current
5
2.5
aaa-011176
15
IDD
(mA)
12.5
default
cpu performance
efficiency
low-current
5
2.5
0
0
0
10
20
30
40
system clock frequency (MHz)
Measured with Keil uVision v.4.72.
50
0
10
20
30
40
system clock frequency (MHz)
50
Measured with Keil uVision v.4.60.
Conditions: Conditions: VDD = 3.3 V; active mode; all peripherals except one UART and the SCTimer/PWM disabled in the
SYSAHBCLKCTRL register; internal pull-up resistors enabled; BOD disabled.
Fig 22. Active mode: CoreMark power consumption IDD for different power mode settings of the power profiles
The CoreMark scores serve as a guideline to select the best power mode for a given
application. To find the most suitable power mode, run the application in mode and
compare power consumption and performance.
Remark: Applications using the USB can only run in default mode.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
56 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
The power profiles optimize the chip performance for power consumption or core
efficiency by controlling the flash access and core power. As shown in Figure 21 and
Figure 22, different power modes result in different CoreMark scores reflecting the
trade-off of efficiency and power consumption. In CPU and efficiency modes, the power
profiles aim to keep the core efficiency at a maximum for the given system frequency.
Depending on optimal flash access parameters that change with frequency, the CoreMark
score and also the power consumption change. Since the compiled code for CoreMark
testing runs out of flash memory, the CoreMark score depends on the compiler version.
11.3 Peripheral power consumption
The supply current per peripheral is measured as the difference in supply current between
the peripheral block enabled and the peripheral block disabled in the SYSAHBCLKCFG
and PDRUNCFG (for analog blocks) registers. All other blocks are disabled in both
registers and no code accessing the peripheral is executed except for the ADC. Measured
on a typical sample at Tamb = 25 C. Unless noted otherwise, the system oscillator and
PLL are running in both measurements.
The supply currents are shown for system clock frequencies of 12 MHz and 48 MHz.
Table 9.
Power consumption for individual analog and digital blocks
Peripheral
Typical supply current in mA
Notes
n/a
12 MHz
48 MHz
IRC
0.24
-
-
System oscillator running; PLL off; independent
of main clock frequency.
System oscillator at 12 MHz
0.28
-
-
IRC running; PLL off; independent of main clock
frequency.
WatchDog oscillator at
600 kHz/2
0
-
-
System oscillator running; PLL off; independent
of main clock frequency.
BOD
0.05
-
-
Independent of main clock frequency.
System PLL
0.25
-
-
-
USB PLL
0.37
-
-
-
CLKOUT
-
0.25
0.89
System PLL is source of CLKOUT.
ROM
-
0.09
0.37
-
FLASHREG
-
0.17
0.66
-
FLASHARRAY
-
0.13
0.52
-
SRAM1
-
0.15
0.59
-
USB SRAM
-
0.14
0.56
-
GPIO + pin interrupt/pattern
match
-
0.18
0.69
GPIO pins configured as outputs and set to
LOW. Direction and pin state are maintained if
the GPIO is disabled in the SYSAHBCLKCFG
register.
IOCON
-
0.08
0.30
-
SCTimer0/PWM +
SCTimer1/PWM
-
0.29
1.1
-
CT16B0
-
0.05
0.17
-
CT16B1
-
0.04
0.16
-
CT32B0
-
0.04
0.13
-
CT32B1
-
0.03
0.13
-
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
57 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 9.
Power consumption for individual analog and digital blocks …continued
Peripheral
Typical supply current in mA
Notes
n/a
12 MHz
48 MHz
RTC
-
0.02
0.10
-
WWDT
-
0.05
0.17
Main clock selected as clock source for the
WDT.
I2C0
-
0.05
0.22
-
I2C1
-
0.05
0.18
-
SSP0
-
0.15
0.59
-
SSP1
-
0.15
0.58
-
USART0
-
0.31
1.19
-
USART1
-
0.12
0.50
-
USART2
-
0.13
0.49
-
USART3 + USART4
-
0.21
0.81
-
USB
-
0.43
0.72
Register interface disabled in
SYSAHBCLKCTRL.
USB PHY
0.54
-
-
ADC0
-
2.15
2.68
Register interface disabled in
SYSAHBCLKCTRL and analog block disabled
in PDRUNCFG registers. Power consumption
measured while the ADC is sampling a single
channel with an ADC clock of 12 MHz or
48 MHz.
Temperature sensor
0.18
-
-
-
DMA
-
0.28
1.1
-
CRC
-
0.04
0.14
-
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
58 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
11.4 Electrical pin characteristics
DDD
92+
9
9ƒ&
9 ƒ&
9ƒ&
9ƒ&
,2+P$
9 ƒ&
&
9 ƒ&
&
9 ƒ&
&
9 ƒ&
&
DDD
92+
9
Conditions: VDD = 2.4 V; ON pin PIO0_7 and PIO1_31.
,2+P$
Conditions: VDD = 3.3 V; ON pin PIO0_7 and PIO1_31.
Fig 23. High-drive output: Typical HIGH-level output voltage VOH versus HIGH-level output current IOH
DDD
9 ƒ&
9&
9ƒ&
9&
9ƒ&
9&
9ƒ&
9&
,2/
P$
92/9
Conditions: VDD = 2.4 V; on pins PIO0_4 and PIO0_5.
Fig 24.
I2C-bus
9ƒ
9 &
9ƒ
9 &
9ƒ
9 &
9ƒ
9 &
DDD
,2/
P$
92/9
Conditions: VDD = 3.3 V; on pins PIO0_4 and PIO0_5.
pins (high current sink): Typical LOW-level output current IOL versus LOW-level output voltage
VOL
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
59 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
DDD
,2/
P$
DDD
,2/
P$
9 ƒ&
&
9 ƒ&
&
9 ƒ&
&
9 ƒ&
&
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
92/9
Conditions: VDD = 2.4 V; standard port pins and
high-drive pins PIO0_7 and PIO1_31.
92/9
Conditions: VDD = 3.3 V; standard port pins and
high-drive pins PIO0_7 and PIO1_31.
Fig 25. Typical LOW-level output current IOL versus LOW-level output voltage VOL
DDD
92+
9
92+
9
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
DDD
,2+P$
Conditions: VDD = 2.4 V; standard port pins.
,2+P$
Conditions: VDD = 3.3 V; standard port pins.
Fig 26. Typical HIGH-level output voltage VOH versus HIGH-level output source current IOH
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
60 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
DDD
,38
ȝ$
DDD
,38
ȝ$
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
9,9
Conditions: VDD = 2.4 V; standard port pins.
9,9
Conditions: VDD = 3.3 V; standard port pins.
Fig 27. Typical pull-up current IPU versus input voltage VI
DDD
,3'
ȝ$
DDD
,3'
ȝ$
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
9ƒ&
9
&
9 &
9ƒ&
9 &
9ƒ&
9 &
9ƒ&
9,9
Conditions: VDD = 2.4 V; standard port pins.
9,9
Conditions: VDD = 3.3 V; standard port pins.
Fig 28. Typical pull-down current IPD versus input voltage VI
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
61 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
12. Dynamic characteristics
12.1 Flash/EEPROM memory
Table 10. Flash characteristics
Tamb = 40 C to +105 C. Based on JEDEC NVM qualification. Failure rate < 10 ppm for parts as
specified below.
Symbol
Parameter
Nendu
endurance
Conditions
tret
retention time
Min
Typ
Max
Unit
10000
100000
-
cycles
powered
10
20
-
years
unpowered
20
40
-
years
page or multiple
consecutive pages,
sector or multiple
consecutive
sectors
95
100
105
ms
0.95
1
1.05
ms
[1]
ter
erase time
tprog
programming
time
[2]
[1]
Number of program/erase cycles.
[2]
Programming times are given for writing 256 bytes to the flash. Tamb <= +85 C. Flash programming with
IAP calls (see LPC11U6x user manual).
Table 11. EEPROM characteristics
Tamb = 40 C to +85 C; VDD = 2.7 V to 3.6 V. Based on JEDEC NVM qualification. Failure rate <
10 ppm for parts as specified below.
Symbol
Parameter
Conditions
Nendu
endurance
tret
retention time
programming
time
tprog
Min
Typ
Max
Unit
100000
1000000
-
cycles
powered
100
200
-
years
unpowered
150
300
-
years
64 bytes
-
2.9
-
ms
12.2 External clock for the oscillator in slave mode
Remark: The input voltage on the XTAL1/2 pins must be  1.95 V (see Table 8). For
connecting the oscillator to the XTAL pins, also see Section 14.4.
Table 12. Dynamic characteristic: external clock (XTALIN input)
Tamb = 40 C to +105 C; VDD over specified ranges.[1]
Min
Typ[2]
Max
Unit
oscillator frequency
1
-
25
MHz
Tcy(clk)
clock cycle time
40
-
1000
ns
tCHCX
clock HIGH time
Tcy(clk)  0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk)  0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
Symbol
Parameter
fosc
[1]
LPC11U6x
Product data sheet
Conditions
Parameters are valid over operating temperature range unless otherwise specified.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
62 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
[2]
Typical ratings are not guaranteed. The values listed are for room temperature (25 C), nominal supply
voltages.
W&+&/
W&+&;
W&/&+
W&/&;
7F\FON
DDD
Fig 29. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
12.3 Internal oscillators
Table 13. Dynamic characteristics: IRC
Tamb = 40 C to +105 C; 2.7 V  VDD  3.6 V[1].
Typ[2]
Max
Unit
25 C  Tamb  +85 C 12 - 1%
12
12 + 1 %
MHz
40 C  Tamb < 25 C 12 - 2%
12
12 + 1 %
MHz
Symbol
Parameter
Conditions
fosc(RC)
internal RC
oscillator frequency
Min
85 C < Tamb  105 C
12 - 1.5 % 12
12 + 1.5 % MHz
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are for room temperature (25 C), nominal supply
voltages.
DDD
I
0+]
9
9
9
9
WHPSHUDWXUHƒ&
Conditions: Frequency values are typical values. 12 MHz  1 % accuracy is guaranteed for
2.7 V  VDD  3.6 V and Tamb = 25 C to +85 C. Variations between parts may cause the IRC to
fall outside the 12 MHz  1 % accuracy specification for voltages below 2.7 V.
Fig 30. Typical Internal RC oscillator frequency versus temperature
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
63 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 14.
Dynamic characteristics: WatchDog oscillator
Symbol
Parameter
Conditions
fosc(int)
internal oscillator
frequency
DIVSEL = 0x1F, FREQSEL = 0x1
in the WDTOSCCTRL register;
DIVSEL = 0x00, FREQSEL = 0xF
in the WDTOSCCTRL register
Min
Typ[1] Max Unit
[2][3]
-
9.4
-
kHz
[2][3]
-
2300
-
kHz
[1]
Typical ratings are not guaranteed. The values listed are at nominal supply voltages.
[2]
The typical frequency spread over processing and temperature (Tamb = 40 C to +105 C) is 40 %.
[3]
See the LPC11U6x user manual.
12.4 I/O pins
Table 15. Dynamic characteristics: I/O pins[1]
Tamb = 40 C to +105 C; 3.0 V  VDD  3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
pin configured as output
3.0
-
5.0
ns
tf
fall time
pin configured as output
2.5
-
5.0
ns
[1]
Applies to standard port pins and RESET pin.
12.5 I2C-bus
Table 16. Dynamic characteristic: I2C-bus pins[1]
Tamb = 40 C to +105 C.[2]
Symbol
Parameter
Conditions
Min
Max
Unit
fSCL
SCL clock
frequency
Standard-mode
0
100
kHz
tf
[4][5][6][7]
fall time
Fast-mode
0
400
kHz
Fast-mode Plus; on
pins PIO0_4 and
PIO0_5
0
1
MHz
of both SDA and
SCL signals
-
300
ns
Fast-mode
20 + 0.1  Cb
300
ns
Fast-mode Plus;
on pins PIO0_4
and PIO0_5
-
120
ns
Standard-mode
4.7
-
s
Fast-mode
1.3
-
s
Fast-mode Plus; on
pins PIO0_4 and
PIO0_5
0.5
-
s
Standard-mode
4.0
-
s
Fast-mode
0.6
-
s
Fast-mode Plus; on
pins PIO0_4 and
PIO0_5
0.26
-
s
Standard-mode
tLOW
tHIGH
LPC11U6x
Product data sheet
LOW period of
the SCL clock
HIGH period of
the SCL clock
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
64 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 16. Dynamic characteristic: I2C-bus pins[1] …continued
Tamb = 40 C to +105 C.[2]
Symbol
tHD;DAT
tSU;DAT
Parameter
data hold time
data set-up
time
[3][4][8]
[9][10]
Conditions
Min
Max
Unit
Standard-mode
0
-
s
Fast-mode
0
-
s
Fast-mode Plus; on
pins PIO0_4 and
PIO0_5
0
-
s
Standard-mode
250
-
ns
Fast-mode
100
-
ns
Fast-mode Plus; on
pins PIO0_4 and
PIO0_5
50
-
ns
[1]
See the I2C-bus specification UM10204 for details.
[2]
Parameters are valid over operating temperature range unless otherwise specified.
[3]
tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission
and the acknowledge.
[4]
A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the
VIH(min) of the SCL signal) to bridge the undefined region of the falling edge of SCL.
[5]
Cb = total capacitance of one bus line in pF.
[6]
The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA
output stage tf is specified at 250 ns. This allows series protection resistors to be connected in between the
SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf.
[7]
In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors
are used, designers should allow for this when considering bus timing.
[8]
The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than
the maximum of tVD;DAT or tVD;ACK by a transition time (see UM10204). This maximum must only be met if
the device does not stretch the LOW period (tLOW) of the SCL signal. If the clock stretches the SCL, the
data must be valid by the set-up time before it releases the clock.
[9]
tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in
transmission and the acknowledge.
[10] A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement
tSU;DAT = 250 ns must then be met. This will automatically be the case if the device does not stretch the
LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must
output the next data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the
Standard-mode I2C-bus specification) before the SCL line is released. Also the acknowledge timing must
meet this set-up time.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
65 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
WI
6'$
W68'$7
W+''$7
WI
6&/
W9''$7
W+,*+
W/2:
6
I6&/
DDD
Fig 31. I2C-bus pins clock timing
12.6 SSP interface
Table 17.
Dynamic characteristics of SPI pins in SPI mode
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
-
-
ns
SPI master (in SPI mode)
Tcy(clk)
full-duplex mode
[1]
50
when only transmitting
[1]
40
in SPI mode
[2]
15
-
-
ns
in SPI mode
[2]
0
-
-
ns
data output valid time in SPI mode
[2]
-
-
10
ns
data output hold time in SPI mode
[2]
0
-
-
ns
clock cycle time
data set-up time
tDS
data hold time
tDH
tv(Q)
th(Q)
ns
SPI slave (in SPI mode)
Tcy(PCLK)
PCLK cycle time
data set-up time
tDS
20
-
-
ns
in SPI mode
[3][4]
0
-
-
ns
tDH
data hold time
in SPI mode
[3][4]
3  Tcy(PCLK) + 4
-
-
ns
tv(Q)
data output valid time in SPI mode
[3][4]
-
-
3  Tcy(PCLK) + 11
ns
th(Q)
data output hold time in SPI mode
[3][4]
-
-
2  Tcy(PCLK) + 5
ns
[1]
Tcy(clk) = (SSPCLKDIV  (1 + SCR)  CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the
main clock frequency fmain, the SPI peripheral clock divider (SSPCLKDIV), the SPI SCR parameter (specified in the SSP0CR0 register),
and the SPI CPSDVSR parameter (specified in the SPI clock prescale register).
[2]
Tamb = 40 C to 105 C; 2.4 V  VDD  3.6 V.
[3]
Tcy(clk) = 12  Tcy(PCLK).
[4]
Tamb = 25 C; for normal voltage supply range: VDD = 3.3 V.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
66 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Tcy(clk)
SCK (CPOL = 0)
SCK (CPOL = 1)
tv(Q)
th(Q)
DATA VALID
MOSI
DATA VALID
tDS
DATA VALID
MISO
DATA VALID
tv(Q)
th(Q)
DATA VALID
MOSI
DATA VALID
tDH
tDS
DATA VALID
MISO
CPHA = 1
tDH
CPHA = 0
DATA VALID
002aae829
Fig 32. SSP master timing in SPI mode
Tcy(clk)
SCK (CPOL = 0)
SCK (CPOL = 1)
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
th(Q)
DATA VALID
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
DATA VALID
CPHA = 1
DATA VALID
th(Q)
CPHA = 0
DATA VALID
002aae830
Fig 33. SSP slave timing in SPI mode
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
67 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
12.7 USART interface
The maximum USART bit rate for all USARTs is 3.125 Mbit/s in asynchronous mode and
10 Mbit/s in synchronous slave and master mode.
Table 18. USART dynamic characteristics USART0
Tamb = 40 C to 105 C; 2.4 V <= VDD <= 3.6 V; CL = 10 pF. Simulated parameters sampled at the
50 % level of the falling or rising edge; values guaranteed by design.
Symbol
Tcy(clk)
Parameter
clock cycle time
[1]
Min
Max
Unit
100
-
ns
USART master (in synchronous mode)
tsu(D)
data input set-up time
44
-
ns
th(D)
data input hold time
0
-
ns
tv(Q)
data output valid time
-
10
ns
th(Q)
data output hold time
0
-
ns
USART slave (in synchronous mode)
tsu(D)
data input set-up time
5
-
ns
th(D)
data input hold time
20
-
ns
tv(Q)
data output valid time
-
40
ns
th(Q)
data output hold time
25
-
ns
[1]
Tcy(clk) = (main clock cycle time)/(UARTCLKDIV x 2 x (256 x DLM + DLL)). See the LPC11U6x User
manual UM10732.
Table 19. USART dynamic characteristics USART1/2/3/4
Tamb = 40 C to 105 C; 2.4 V <= VDD <= 3.6 V; CL = 10 pF. Simulated parameters sampled at the
50 % level of the falling or rising edge; values guaranteed by design.
Symbol
Tcy(clk)
Parameter
clock cycle time
[1]
Min
Max
Unit
100
-
ns
USART master (in synchronous mode)
tsu(D)
data input set-up time
44
-
ns
th(D)
data input hold time
0
-
ns
tv(Q)
data output valid time
-
10
ns
th(Q)
data output hold time
0
-
ns
USART slave (in synchronous mode)
tsu(D)
data input set-up time
5
-
ns
th(D)
data input hold time
0
-
ns
tv(Q)
data output valid time
-
40
ns
th(Q)
data output hold time
20
-
ns
[1]
LPC11U6x
Product data sheet
Tcy(clk) = U_PCLK/BRGVAL. See the LPC11U6x User manual UM10732.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
68 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
7F\FON
8QB6&/.&/.32/ 8QB6&/.&/.32/ WY4
WK4
67$57
7;'
%,7
%,7
WVX' WK'
67$57
5;'
%,7
%,7
DDD
Fig 34. USART timing
12.8 SCTimer/PWM output timing
Table 20. SCTimer/PWM output dynamic characteristics
Tamb = 40 C to 105 C; 2.4 V <= VDD <= 3.6 V. Simulated skew (over process, voltage, and
temperature) between any two SCT outputs; sampled at the 50 % level of the falling or rising edge;
values guaranteed by design.
Symbol
Parameter
Min
Max
Unit
<1
2
ns
<1
2
ns
SCTimer0/PWM
tsk(o)
output skew time
SCTimer1/PWM
tsk(o)
LPC11U6x
Product data sheet
output skew time
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
69 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
13. Characteristics of analog peripherals
Table 21. BOD static characteristics[1]
Tamb = 25 C.
Symbol
Parameter
Conditions
Vth
threshold voltage
interrupt level 2
Min
Typ
Max
Unit
assertion
-
2.54
-
V
de-assertion
-
2.68
-
V
assertion
-
2.82
-
V
de-assertion
-
2.93
-
V
assertion
-
2.34
-
V
de-assertion
-
2.49
-
V
assertion
-
2.62
-
V
de-assertion
-
2.77
-
V
interrupt level 3
reset level 2
reset level 3
[1]
LPC11U6x
Product data sheet
Interrupt and reset levels are selected by writing the level value to the BOD control register BODCTRL, see
the LPC11U6x user manual. Interrupt levels 0 and 1 are reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
70 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Table 22. 12-bit ADC static characteristics
Tamb = 40 C to +105 C; VDD = 2.4 V to 3.6 V; VREFP = VDDA; VSSA = 0; VREFN = VSSA. ADC
calibrated at T = 25C.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
[1]
VIA
analog input
voltage
[2]
0
-
VDDA
V
Cia
analog input
capacitance
[3]
-
-
0.32
pF
fclk(ADC)
ADC clock
frequency
VDDA 2.7 V
50
MHz
VDDA 2.4 V
25
MHz
sampling
frequency
VDDA 2.7 V
-
-
2
Msamples/s
VDDA 2.4 V
-
-
1
Msamples/s
-
-
2.5
LSB
fs
LPC11U6x
Product data sheet
ED
differential
linearity error
[4]
EL(adj)
integral
non-linearity
[5]
-
-
2.5
LSB
EO
offset error
[6]
-
-
4.5
LSB
Verr(FS)
full-scale error
voltage
[7]
-
-
0.5
%
Zi
input
impedance
0.1
-
-
M
fs = 2 Msamples/s
[8][9]
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
[2]
The input resistance of ADC channel 0 is higher than for all other channels.
[3]
Cia represents the external capacitance on the analog input channel for sampling speeds of 2 Msamples/s.
[4]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width.
See Figure 35.
[5]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and
the ideal transfer curve after appropriate adjustment of gain and offset errors. See Figure 35.
[6]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the
straight line which fits the ideal curve. See Figure 35.
[7]
The full-scale error voltage or gain error (EG) is the difference between the straight-line fitting the actual
transfer curve after removing offset error, and the straight line which fits the ideal transfer curve. See
Figure 35.
[8]
Tamb = 25 C; maximum sampling frequency fs = 2 Msamples/s and analog input capacitance Cia = 0.32 pF.
[9]
Input impedance Zi is inversely proportional to the sampling frequency and the total input capacity including
Cia: Zi  1 / (fs  Ci). See Table 8 for Cio.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
71 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
offset
error
EO
gain
error
EG
4095
4094
4093
4092
4091
4090
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
4090
4091
4092
4093
4094
4095
4096
VIA (LSBideal)
offset error
EO
1 LSB =
VREFP - VSS
4096
002aaf436
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 35. 12-bit ADC characteristics
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
72 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
ADC
R1 = 0.25 kΩ...2.5 kΩ
ADCn_0
Cio
Rsw = 5 Ω...25 Ω
ADCn_[1:11]
DAC
CDAC
Cio
Cia
aaa-011748
Fig 36. ADC input impedance
Table 23. Temperature sensor static and dynamic characteristics
VDDA = 2.4 V to 3.6 V
Symbol
Parameter
Conditions
DTsen
sensor
temperature
accuracy
Tamb = 40 C to +105 C
EL
linearity error
Tamb = 40 C to +105 C
ts(pu)
power-up
settling time
[1]
[2]
to 99% of temperature
sensor output value
Min
Typ
Max
Unit
-
5
-
C
-
4
-
C
-
14
-
s
[1]
Absolute temperature accuracy.
[2]
Typical values are derived from nominal simulation (VDDA = 3.3 V; Tamb = 27 C; nominal process models).
Table 24. Temperature sensor Linear-Least-Square (LLS) fit parameters
VDDA = 2.4 V to 3.6 V
LPC11U6x
Product data sheet
Fit parameter
Range
Min
Typ
Max
Unit
LLS slope
Tamb = 40 C to +105 C
-
-2.36
-
mV/C
LLS intercept
Tamb = 40 C to +105C
-
606
-
mV
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
73 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
DDD
92
P9
WHPSHUDWXUHƒ&
VDDA = 3.3 V; measured on a typical silicon sample.
Fig 37. Typical LLS fit of the temperature sensor output voltage
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
74 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
14. Application information
14.1 ADC usage notes
The following guidelines show how to increase the performance of the ADC in a noisy
environment beyond the ADC specifications listed in Table 22:
• The ADC input trace must be short and as close as possible to the LPC11U6x chip.
• The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
• If the ADC and the digital core share a power supply, the power supply line must be
adequately filtered.
• To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
14.2 Typical wake-up times
Table 25. Typical wake-up times
VDD = 3.3 V; Tamb = 25 °C
Power modes
Wake-up time
Sleep mode (12 MHz)[1][2]
2.6 s
Deep-sleep mode[1][3]
4.4 s
Power-down
86.8 s
mode[1][3]
Deep Power-down
mode[4]
276 s
[1]
The wake-up time measured is the time between when a GPIO input pin is triggered to wake up the device
from the low-power modes and from when a GPIO output pin is set in the interrupt service routine (ISR)
wake-up handler.
[2]
IRC enabled, all peripherals off.
[3]
WatchDog oscillator disabled, Brown-Out Detect (BOD) disabled.
[4]
Wake-up from deep power-down causes the part to go through entire reset process. The wake-up time
measured is the time between when a wake-up pin is triggered to wake up the device from the low-power
modes and when a GPIO output pin is set in the reset handler.
14.3 Suggested USB interface solutions
The USB device can be connected to the USB as self-powered device (see Figure 38) or
bus-powered device (see Figure 39).
On the LPC11U6x, the PIO0_3/USB_VBUS pin is 5 V tolerant only when VDD is applied
and at operating voltage level. Therefore, if the USB_VBUS function is connected to the
USB connector and the device is self-powered, the USB_VBUS pin must be protected for
situations when VDD = 0 V.
If VDD is always at operating level while VBUS = 5 V, the USB_VBUS pin can be
connected directly to the VBUS pin on the USB connector.
For systems where VDD can be 0 V and VBUS is directly applied to the VBUS pin,
precautions must be taken to reduce the voltage to below 3.6 V, which is the maximum
allowable voltage on the USB_VBUS pin in this case.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
75 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
One method is to use a voltage divider to connect the USB_VBUS pin to the VBUS on the
USB connector. The voltage divider ratio should be such that the USB_VBUS pin is
greater than 0.7 VDD to indicate a logic HIGH while below the 3.6 V allowable maximum
voltage.
For the following operating conditions
VBUSmax = 5.25 V
VDD = 3.6 V,
the voltage divider should provide a reduction of 3.6 V/5.25 V or ~0.686 V.
LPC1xxx
VDD
USB_CONNECT
R2
R3
USB
R1
1.5 kΩ
USB_VBUS
RS = 33 Ω
USB_DP
RS = 33 Ω
USB_DM
D+
D-
USB-B
connector
VSS
aaa-010820
Fig 38. USB interface on a self-powered device where USB_VBUS = 5 V
The USB_CONNECT function can be enabled internally by setting the DCON bit in the
DEVCMDSTAT register to prevent the USB from timing out when there is a significant
delay between power-up and handling USB traffic. External circuitry is not required for the
USB_CONNECT functionality.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
76 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
LPC1xxx
VDD
REGULATOR
USB_CONNECT
USB
R1
1.5 kΩ
USB_VBUS(1)
USB_VBUS(2)
RS = 33 Ω
USB_DP
RS = 33 Ω
USB_DM
VBUS
D+
D-
USB-B
connector
VSS
aaa-010821
Two options exist for connecting VBUS to the USB_VBUS pin:
(1) Connect the regulator output to USB_VBUS. In this case, the USB_VBUS signal is HIGH whenever the part is powered.
(2) Connect the VBUS signal directly from the connector to the USB_VBUS pin. In this case, 5 V are applied to the USB_VBUS pin
while the regulator is ramping up to supply VDD. Since the PIO0_3/USB_VBUS pin is only 5 V tolerant when VDD is at operating
level, this connection can degrade the performance of the part over its lifetime. Simulation shows that lifetime is reduced to
15 years at Tamb = 45 °C and 8 years at Tamb = 55 °C assuming that USB_VBUS = 5 V is applied continuously while VDD = 0 V.
Fig 39. USB interface on a bus-powered device
Remark: When a self-powered circuit is used without connecting VBUS, configure the
PIO0_3/USB_VBUS pin for GPIO (PIO0_3) and provide software that can detect the host
presence through some other mechanism before enabling USB_CONNECT and the
SoftConnect feature. Enabling the SoftConnect without host presence leads to USB
compliance failure.
14.3.1 USB Low-speed operation
The USB device controller can be used in low-speed mode supporting 1.5 Mbit/s data
exchange with a USB host controller.
Remark: To operate in low-speed mode, change the board connections as follows:
1. Connect USB_DP to the D- pin of the connector.
2. Connect USB_DM to the D+ pin of the connector.
Use the IRC as clock source for the USB PLL to generate 48 MHz, then set the USB clock
divider USBCLKDIV to 8 for a 6 MHz USB clock (see Figure 10 “Clock generation”).
External 10 Ω resistors are recommended in low-speed mode to reduce over-shoots and
accommodate for 5 m cable length required for USB-IF testing.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
77 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
SYSCON
12 MHz
IRC
USB PLL
48 MHz
USBCLKDIV
/8
USB main clock
= 6 MHz
VDD
USB_CONNECT
USB
R1
1.5 kΩ
USB_VBUS
RS = 33 Ω
USB_DP
RS = 10 Ω
RS = 33 Ω
USB_DM
RS = 10 Ω
D+
D-
USB-B
connector
VSS
aaa-011021
Fig 40. USB interface for low-speed, XTAL-less operation
14.4 XTAL input and crystal oscillator component selection
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
Ci = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave
mode, a minimum of 200 mV(RMS) is needed.
LPC1xxx
XTALIN
Ci
100 pF
Cg
002aae788
Fig 41. Slave mode operation of the on-chip oscillator
In slave mode the input clock signal should be coupled through a capacitor of 100 pF
(Figure 41), with an amplitude between 200 mV (RMS) and 1000 mV (RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
78 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
External components and models used in oscillation mode are shown in Figure 42 and in
Table 26 and Table 27. Since the feedback resistance is integrated on chip, only a crystal
and the capacitances CX1 and CX2 must be connected externally in case of fundamental
mode oscillation (the fundamental frequency is represented by L, CL and RS).
Capacitance CP in Figure 42 represents the parallel package capacitance and should not
be larger than 7 pF. Parameters FOSC, CL, RS and CP are supplied by the crystal
manufacturer (see Table 26).
LPC1xxx
L
XTALIN
XTALOUT
CL
=
CP
XTAL
RS
CX2
CX1
002aaf424
Fig 42. Oscillator modes and models: oscillation mode of operation and external crystal
model used for CX1/CX2 evaluation
Table 26.
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) low frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
1 MHz to 5 MHz
10 pF
< 300 
18 pF, 18 pF
20 pF
< 300 
39 pF, 39 pF
30 pF
< 300 
57 pF, 57 pF
10 pF
< 300 
18 pF, 18 pF
20 pF
< 200 
39 pF, 39 pF
30 pF
< 100 
57 pF, 57 pF
10 MHz to 15 MHz
10 pF
< 160 
18 pF, 18 pF
20 pF
< 60 
39 pF, 39 pF
15 MHz to 20 MHz
10 pF
< 80 
18 pF, 18 pF
5 MHz to 10 MHz
Table 27.
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) high frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
15 MHz to 20 MHz
10 pF
< 180 
18 pF, 18 pF
20 pF
< 100 
39 pF, 39 pF
10 pF
< 160 
18 pF, 18 pF
20 pF
< 80 
39 pF, 39 pF
20 MHz to 25 MHz
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
79 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
14.5 XTAL Printed-Circuit Board (PCB) layout guidelines
The crystal should be connected on the PCB as close as possible to the oscillator input
and output pins of the chip. Take care that the load capacitors Cx1, Cx2, and Cx3 in case of
third overtone crystal usage have a common ground plane. The external components
must also be connected to the ground plane. Loops must be made as small as possible to
keep the noise coupled in via the PCB as small as possible. Also parasitics should stay as
small as possible. Smaller values of Cx1 and Cx2 should be chosen according to the
increase in parasitics of the PCB layout.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
80 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
14.6 RTC oscillator component selection
The 32 kHz crystal must be connected to the part via the RTCXIN and RTCXOUT pins as
shown in Figure 43. If the RTC is not used, the RTCXIN pin can be grounded.
LPC1xxx
L
RTCXIN
RTCXOUT
=
CL
CP
XTAL
RS
CX2
CX1
aaa-010822
Fig 43. RTC oscillator components
Select Cx1 and Cx2 based on the external 32 kHz crystal used in the application circuitry.
The pad capacitance CP of the RTCXIN and RTCXOUT pad is 3 pF. If the load
capacitance of the external crystal is CL, the optimal Cx1 and Cx2 can be selected as:
Cx1 = Cx2 = 2 x CL – CP
14.7 Connecting power, clocks, and debug functions
Figure 44 shows the basic board connections used to power the LPC11U6x, connect the
external crystal and the 32 kHz oscillator for the RTC, and provide debug capabilities via
the serial wire port.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
81 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
3.3 V
3.3 V
SWD connector
Note 6
~10 kΩ - 100 kΩ
SWDIO/PIO0_15
1
2
3
4
5
6
n.c.
7
8
n.c.
9
10
SWCLK/PIO0_10
PIO2_0/XTALIN
~10 kΩ - 100 kΩ
C1
n.c.
Note 1
DGND
C2
PIO2_1/XTALOUT
RESET/PIO0_0
DGND
RTCXIN
Note 2
C3
VSS
DGND
C4
RTCXOUT
DGND
DGND
0.1 μF
AGND
Note 3
VDD (2 to 5 pins)
VSSA
3.3 V
0.01 μF
LPC11U6x
PIO0_1
DGND
Note 4
3.3 V
VDDA
ISP select pins
PIO0_3
0.1 μF
10 μF
Note 7
ADC_0
VREFP
Note 4
DGND
3.3 V
10 μF
0.1 μF
0.1 μF
VREFN
AGND
AGND
Note 5
3.3 V
VBAT
0.1 μF
AGND
DGND
DGND
aaa-013306
(1) See Section 14.4 “XTAL input and crystal oscillator component selection” for the values of C1 and C2.
(2) See Section 14.6 “RTC oscillator component selection” for the values of C3 and C4.
(3) Position the decoupling capacitors of 0.1 μF and 0.01 μF as close as possible to the VDD pin. Add one set of decoupling
capacitors to each VDD pin.
(4) Position the decoupling capacitors of 0.1 μF as close as possible to the VREFN and VDDA pins. The 10 μF bypass capacitor
filters the power line. Tie VDDA and VREFP to VDD if the ADC is not used. Tie VREFN to VSS if ADC is not used.
(5) Position the decoupling capacitor of 0.1 μF as close as possible to the VBAT pin. Tie VBAT to VDD if not used.
(6) Uses the ARM 10-pin interface for SWD.
(7) When measuring signals of low frequency, use a low-pass filter to remove noise and to improve ADC performance. Also see
Ref. 3.
Fig 44. Power, clock, and debug connections
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
82 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
14.8 Termination of unused pins
Table 28 shows how to terminate pins that are not used in the application. In many cases,
unused pins may should be connected externally or configured correctly by software to
minimize the overall power consumption of the part.
Unused pins with GPIO function should be configured as outputs set to LOW with their
internal pull-up disabled. To configure a GPIO pin as output and drive it LOW, select the
GPIO function in the IOCON register, select output in the GPIO DIR register, and write a 0
to the GPIO PORT register for that pin. Disable the pull-up in the pin’s IOCON register.
In addition, it is recommended to configure all GPIO pins that are not bonded out on
smaller packages as outputs driven LOW with their internal pull-up disabled.
Table 28.
Termination of unused pins
Pin
Default
state[1]
Recommended termination of unused pins
RESET/PIO0_0
I; PU
In an application that does not use the RESET pin or its GPIO function, the
termination of this pin depends on whether Deep power-down mode is used:
•
Deep power-down used: Connect an external pull-up resistor and keep pin in
default state (input, pull-up enabled) during all other power modes.
•
Deep power-down not used and no external pull-up connected: can be left
unconnected if internal pull-up is disabled and pin is driven LOW and
configured as output by software.
all PIOn_m (not
open-drain)
I; PU
Can be left unconnected if driven LOW and configured as GPIO output with pull-up
disabled by software.
PIOn_m (I2C open-drain)
IA
Can be left unconnected if driven LOW and configured as GPIO output by software.
RSTOUT
IA; O
Can be left unconnected. Not configurable by software.
USB_DP/USB_DM
F
Can be left unconnected. When the USP PHY is disabled, the pins are LOW.
RTCXIN
-
Connect to ground. When grounded, the RTC oscillator is disabled.
RTCXOUT
-
Can be left unconnected.
VREFP
-
Tie to VDD.
VREFN
-
Tie to VSS.
VDDA
-
Tie to VDD.
VBAT
-
Tie to VDD if no external battery connected.
VSSA
-
Tie to VSS.
[1]
I = Input, O = Output, IA = Inactive (no pull-up/pull-down enabled), F = floating, PU = Pull-Up.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
83 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
14.9 Pin states in different power modes
Table 29.
Pin states in different power modes
Pin
Active
Sleep
Deep-sleep/Powerdown
PIOn_m pins (not As configured in the IOCON[1]. Default: internal pull-up
enabled.
I2C)
Deep power-down
Floating.
PIO0_4, PIO0_5
(open-drain
I2C-bus pins)
As configured in the IOCON[1].
Floating.
RESET
Reset function enabled. Default: input, internal pull-up
enabled.
Reset function disabled; floating; if the part
is in deep power-down mode, the RESET
pin needs an external pull-up to reduce
power consumption.
PIO0_16/
WAKEUP
As configured in the IOCON[1]. WAKEUP function inactive. Wake-up function enabled; can be disabled
by software.
[1]
Default and programmed pin states are retained in sleep, deep-sleep, and power-down modes.
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
84 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
15. Package outline
LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
SOT313-2
c
y
X
36
25
A
37
24
ZE
e
E HE
A A2
(A 3)
A1
w M
θ
bp
pin 1 index
Lp
L
13
48
detail X
12
1
ZD
e
v M A
w M
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HD
HE
L
Lp
v
w
y
mm
1.6
0.20
0.05
1.45
1.35
0.25
0.27
0.17
0.18
0.12
7.1
6.9
7.1
6.9
0.5
9.15
8.85
9.15
8.85
1
0.75
0.45
0.2
0.12
0.1
Z D (1) Z E (1)
θ
0.95
0.55
7o
o
0
0.95
0.55
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT313-2
136E05
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-25
Fig 45. Package outline LQFP48 (SOT313-2)
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
85 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm
SOT314-2
c
y
X
A
48
33
49
32
ZE
e
E HE
A
A2
(A 3)
A1
wM
θ
bp
pin 1 index
64
Lp
L
17
detail X
16
1
ZD
e
v M A
wM
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.20
0.05
1.45
1.35
0.25
0.27
0.17
0.18
0.12
10.1
9.9
10.1
9.9
0.5
HD
HE
12.15 12.15
11.85 11.85
L
Lp
v
w
y
1
0.75
0.45
0.2
0.12
0.1
Z D (1) Z E (1)
1.45
1.05
1.45
1.05
θ
7o
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT314-2
136E10
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-25
Fig 46. Package outline LQFP64 (SOT314-2)
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
86 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
LQFP100: plastic low profile quad flat package; 100 leads; body 14 x 14 x 1.4 mm
SOT407-1
c
y
X
A
51
75
50
76
ZE
e
E HE
A A2
(A 3)
A1
w M
θ
bp
Lp
pin 1 index
L
100
detail X
26
1
25
ZD
e
v M A
w M
bp
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.15
0.05
1.45
1.35
0.25
0.27
0.17
0.20
0.09
14.1
13.9
14.1
13.9
0.5
HD
HE
16.25 16.25
15.75 15.75
L
Lp
v
w
y
1
0.75
0.45
0.2
0.08
0.08
Z D (1) Z E (1)
1.15
0.85
1.15
0.85
θ
7o
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT407-1
136E20
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-02-01
03-02-20
Fig 47. Package outline LQFP100 (SOT407-1)
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
87 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
16. Soldering
Footprint information for reflow soldering of LQFP48 package
SOT313-2
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
P2
0.500
0.560
Ax
Ay
10.350 10.350
Bx
By
C
D1
D2
Gx
7.350
7.350
1.500
0.280
0.500
7.500
Gy
Hx
Hy
7.500 10.650 10.650
sot313-2_fr
Fig 48. Reflow soldering for the LQFP48 package
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
88 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Footprint information for reflow soldering of LQFP64 package
SOT314-2
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
0.500
P2
Ax
Ay
Bx
By
0.560 13.300 13.300 10.300 10.300
C
D1
D2
1.500
0.280
0.400
Gx
Gy
Hx
Hy
10.500 10.500 13.550 13.550
sot314-2_fr
Fig 49. Reflow soldering for the LQFP64 package
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
89 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Footprint information for reflow soldering of LQFP100 package
SOT407-1
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
0.500
P2
Ax
Ay
Bx
By
0.560 17.300 17.300 14.300 14.300
C
D1
D2
1.500
0.280
0.400
Gx
Gy
Hx
Hy
14.500 14.500 17.550 17.550
sot407-1
Fig 50. Reflow soldering for the LQFP100 package
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
90 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
17. References
LPC11U6x
Product data sheet
[1]
LPC11U6x User manual UM10732:
http://www.nxp.com/documents/user_manual/UM10732.pdf
[2]
LPC11U6x Errata sheet:
http://www.nxp.com/documents/errata_sheet/ES_LPC11U6X.pdf
[3]
Technical note ADC design guidelines:
http://www.nxp.com/documents/technical_note/TN00009.pdf
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
91 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
18. Revision history
Table 30.
Revision history
Document ID
Release date
Data sheet status
Change notice Supersedes
LPC11U6x v.1.2
20140526
Product data sheet
-
Modifications:
LPC11U6x v.1.1
Modifications:
LPC11U6x v.1
LPC11U6x
Product data sheet
LPC11U6x v.1.1
•
•
Part marking updated with revision indicator.
•
•
•
Section 14.7 “Connecting power, clocks, and debug functions” added.
•
Figure 39 “USB interface on a bus-powered device” changed to show USB_VBUS
connection to part.
•
Parts added: LPC11U67JBD100, LPC11U67JBD64, LPC11U66JBD48.
Changed recommendation for VBAT connection if unused: Tie to VDD. See Table 3
“Pin description”.
Section 14.9 “Pin states in different power modes” added.
Remark added about using the regulator in the USB bus-powered set-up. See Section
14.3 “Suggested USB interface solutions”.
20140312
Product data sheet
-
LPC11U6x v.1
•
•
Parameter RI renamed to ZI (input impedance) in Table 22.
•
•
•
•
Parameter Cia corrected in Table 22 “12-bit ADC static characteristics”.
•
Pin description for RESET/PIO0_0 updated: In deep power-down mode, this pin must
be pulled HIGH externally. The RESET pin can be left unconnected or be used as a
GPIO pin if an external RESET function is not needed. See Table 3.
•
•
•
•
Pin functions TMS, TDI, TDO, and TRST changed to default function in Table 3.
Description of the internal USB_CONNECT function clarified in Section 14.3
“Suggested USB interface solutions”. The USB_CONNECT function can be set
internally by software and does not require external circuitry.
Figure 36 “ADC input impedance” added.
Parameter pin capacitance added in Table 8.
Pin description for VBAT updated: If no battery is used, tie VBAT to VDD or to ground.
See Table 3.
Pin description table updated for clarity (VBAT, I2C-bus pins, WAKEUP pin).
Section 14.1 “ADC usage notes” added.
Use of USB_CONNECT signal explained when VBUS is not connected. See
Section 14.3.
20140117
Product data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
-
© NXP Semiconductors N.V. 2014. All rights reserved.
92 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
19. Legal information
19.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
19.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
19.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
LPC11U6x
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
93 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
19.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP Semiconductors N.V.
20. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
94 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
21. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 4
4.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 4
5
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7
Pinning information . . . . . . . . . . . . . . . . . . . . . . 7
7.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 9
8
Functional description . . . . . . . . . . . . . . . . . . 19
8.1
ARM Cortex-M0+ core . . . . . . . . . . . . . . . . . . 19
8.2
AHB multilayer matrix . . . . . . . . . . . . . . . . . . . 19
8.3
On-chip flash programming memory . . . . . . . 21
8.4
EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.5
SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.6
On-chip ROM . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.7
Memory mapping . . . . . . . . . . . . . . . . . . . . . . 21
8.8
Nested Vectored Interrupt Controller (NVIC) . 22
8.8.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.8.2
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 23
8.9
IOCON block . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.9.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.9.2
Standard I/O pad configuration . . . . . . . . . . . . 24
8.10
Fast General-Purpose parallel I/O (GPIO) . . . 24
8.10.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.11
Pin interrupt/pattern match engine . . . . . . . . . 25
8.11.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.12
GPIO group interrupts. . . . . . . . . . . . . . . . . . . 26
8.12.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.13
DMA controller . . . . . . . . . . . . . . . . . . . . . . . . 26
8.13.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.14
USB interface . . . . . . . . . . . . . . . . . . . . . . . . 27
8.14.1
Full-speed USB device controller . . . . . . . . . . 27
8.14.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.15
USART0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.15.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.16
USART1/2/3/4. . . . . . . . . . . . . . . . . . . . . . . . . 28
8.16.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.17
SSP serial I/O controller (SSP0/1) . . . . . . . . . 29
8.17.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.18
I2C-bus serial I/O controller . . . . . . . . . . . . . . 29
8.18.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.19
Timer/PWM subsystem. . . . . . . . . . . . . . . . . . 30
8.19.1
State Configurable Timers (SCTimer0/PWM
and SCTimer1/PWM) . . . . . . . . . . . . . . . . . . . 31
8.19.1.1
8.19.2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General purpose external event
counter/timers (CT32B0/1 and CT16B0/1) . .
8.19.2.1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.20
System tick timer (SysTick) . . . . . . . . . . . . . .
8.21
Windowed WatchDog Timer (WWDT) . . . . . .
8.21.1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.22
Real-Time Clock (RTC) . . . . . . . . . . . . . . . . .
8.22.1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.23
Analog-to-Digital Converter (ADC). . . . . . . . .
8.23.1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.24
Temperature sensor . . . . . . . . . . . . . . . . . . . .
8.25
Clocking and power control . . . . . . . . . . . . . .
8.25.1
Clock generation . . . . . . . . . . . . . . . . . . . . . .
8.25.2
Power domains . . . . . . . . . . . . . . . . . . . . . . .
8.25.3
Integrated oscillators . . . . . . . . . . . . . . . . . . .
8.25.3.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . .
8.25.3.2 System oscillator . . . . . . . . . . . . . . . . . . . . . .
8.25.3.3 WatchDog oscillator . . . . . . . . . . . . . . . . . . . .
8.25.3.4 RTC oscillator . . . . . . . . . . . . . . . . . . . . . . . .
8.25.4
System PLL and USB PLL. . . . . . . . . . . . . . .
8.25.5
Clock output . . . . . . . . . . . . . . . . . . . . . . . . . .
8.25.6
Wake-up process . . . . . . . . . . . . . . . . . . . . . .
8.25.7
Power control . . . . . . . . . . . . . . . . . . . . . . . . .
8.25.7.1 Power profiles . . . . . . . . . . . . . . . . . . . . . . . .
8.25.7.2 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . .
8.25.7.3 Deep-sleep mode. . . . . . . . . . . . . . . . . . . . . .
8.25.7.4 Power-down mode . . . . . . . . . . . . . . . . . . . . .
8.25.7.5 Deep power-down mode . . . . . . . . . . . . . . . .
8.26
System control . . . . . . . . . . . . . . . . . . . . . . . .
8.26.1
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.26.2
Brownout detection . . . . . . . . . . . . . . . . . . . .
8.26.3
Code security (Code Read Protection - CRP)
8.27
Emulation and debugging . . . . . . . . . . . . . . .
9
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
10
Thermal characteristics . . . . . . . . . . . . . . . . .
11
Static characteristics . . . . . . . . . . . . . . . . . . .
11.1
Power consumption . . . . . . . . . . . . . . . . . . . .
11.2
CoreMark data . . . . . . . . . . . . . . . . . . . . . . . .
11.3
Peripheral power consumption . . . . . . . . . . .
11.4
Electrical pin characteristics. . . . . . . . . . . . . .
12
Dynamic characteristics. . . . . . . . . . . . . . . . .
12.1
Flash/EEPROM memory . . . . . . . . . . . . . . . .
12.2
External clock for the oscillator in slave mode
12.3
Internal oscillators . . . . . . . . . . . . . . . . . . . . .
12.4
I/O pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.5
I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
33
33
33
33
33
34
34
34
34
35
36
36
37
37
38
38
38
38
38
38
39
39
39
39
40
40
40
40
40
41
41
43
44
45
46
52
56
57
59
62
62
62
63
64
64
continued >>
LPC11U6x
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 26 May 2014
© NXP Semiconductors N.V. 2014. All rights reserved.
95 of 96
LPC11U6x
NXP Semiconductors
32-bit ARM Cortex-M0+ microcontroller
12.6
SSP interface . . . . . . . . . . . . . . . . . . . . . . . . .
12.7
USART interface. . . . . . . . . . . . . . . . . . . . . . .
12.8
SCTimer/PWM output timing . . . . . . . . . . . . .
13
Characteristics of analog peripherals . . . . . .
14
Application information. . . . . . . . . . . . . . . . . .
14.1
ADC usage notes . . . . . . . . . . . . . . . . . . . . . .
14.2
Typical wake-up times . . . . . . . . . . . . . . . . . .
14.3
Suggested USB interface solutions . . . . . . . .
14.3.1
USB Low-speed operation . . . . . . . . . . . . . . .
14.4
XTAL input and crystal oscillator component
selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.5
XTAL Printed-Circuit Board (PCB) layout
guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.6
RTC oscillator component selection . . . . . . . .
14.7
Connecting power, clocks, and debug
functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.8
Termination of unused pins. . . . . . . . . . . . . . .
14.9
Pin states in different power modes . . . . . . . .
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
16
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
References . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
Revision history . . . . . . . . . . . . . . . . . . . . . . . .
19
Legal information. . . . . . . . . . . . . . . . . . . . . . .
19.1
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
19.2
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.3
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.4
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . .
20
Contact information. . . . . . . . . . . . . . . . . . . . .
21
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
68
69
70
75
75
75
75
77
78
80
81
81
83
84
85
88
91
92
93
93
93
93
94
94
95
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP Semiconductors N.V. 2014.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 26 May 2014
Document identifier: LPC11U6x