AP7342

AP7342
DUAL 150mA HIGH PSRR LOW NOISE LDO WITH ENABLE
Description
Pin Assignments
The AP7342 is a dual low dropout regulator with high output voltage
accuracy, low RDSON, high PSRR, low output noise and low quiescent
current. This regulator is based on a CMOS process.
Each regulator includes a voltage reference, error amplifier, current
limit circuit and an enable input to turn on/off output. With the
integrated resistor network, fixed output voltage versions can be
delivered.
With its low power consumption and line and load transient response,
the AP7342 is well suited for low power handheld communication
equipment.
The AP7342 is packaged in X2-DFN1212-6 package and allows for
smallest footprint and dense PCB layout.
Applications
Features
•
Low VIN and Wide VIN Range: 1.7V to 5.25V
•
•
Guarantee Output Current: 150mA
VOUT Accuracy ±1%
•
•
•
•
•
•
Ripple Rejection: 75dB at 1kHz
Low Output Noise: 60µVrms from 10Hz to 100kHz
Quiescent Current as Low as 35µA
VOUT Fixed 1.2V to 3.6V
Totally Lead-Free & and Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free, Green Device (Note 3)
Notes:
•
•
•
•
•
•
•
Smart Phone/PAD
RF Supply
Cameras
Portable Video
Portable Media Player
Wireless Adapter
Wireless Communication
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
Typical Applications Circuit
AP7342
Document number: DS37614 Rev. 2 - 2
1 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Pin Descriptions
Pin Number
Pin Name
Function
1
VOUT1
Channel 1 Output Voltage Pin
2
VOUT2
Channel 2 Output Voltage Pin
3
GND
Ground
Chanel 2 Enable Pin
4
EN2
5
VIN
This pin should be driven either high or low and must not be floating. Driving this pin high
enables channel 2 output, while pulling it low puts Chanel 2 regulator into shutdown
mode.
Power Input Pin
Chanel 1 Enable Pin
6
EN1
–
Thermal PAD
This pin should be driven either high or low and must not be floating. Driving this pin high
enables channel 1 output, while pulling it low puts Chanel 1 regulator into shutdown
mode.
In PCB layout, it is preferred to use large copper area to cover this pad for better thermal
dissipation, then connect this area to GND or leave it open. However, do not use it as
GND electrode function alone.
Functional Block Diagram
AP7342 (No Discharge)
AP7342
Document number: DS37614 Rev. 2 - 2
AP7342 (With Discharge)
2 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.) (Note 4)
Symbol
Parameter
Rating
Unit
VIN
Input Voltage
6.0
V
VEN
Input Voltage at EN Pins
6.0
V
VOUT
Output Voltage
-0.3 to VIN +0.3
V
IOUT
Output Current
180
mA
PD
Power Dissipation
600
mW
TA
Operating Ambient Temperature
-40 to +85
°C
Storage Temperature
-55 to +125
°C
TSTG
Note:
4. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
Parameter
VIN
Input Voltage
IOUT
Output Current
TA
Operating Ambient Temperature
AP7342
Document number: DS37614 Rev. 2 - 2
3 of 14
www.diodes.com
Min
Max
Unit
1.7
5.25
V
0
150
mA
-40
+85
°C
March 2015
© Diodes Incorporated
AP7342
Electrical Characteristics
(@TA = +25°C, VIN = VOUT+1V (VOUT > 1.5V), VIN = 2.5V (VOUT ≤ 1.5V), IOUT = 1mA, CIN = COUT = 1.0µF, unless otherwise specified.)
Parameter
Input Voltage
Conditions
TA = -40°C to +85°C
VIN = (VOUT-Nom+1.0V) to
Output Voltage Accuracy (Note 11)
TA = +25°C
Min
Typ
Max
Unit
1.7
–
5.25
V
-1
–
1
-1.5
–
1.5
5.25V,
%
TA = -40°C to +85°C
IOUT = 1mA to 150mA
Line Regulation (∆VOUT/∆VIN/VOUT)
VIN = (VOUT-Nom+1.0V) to 5.25V, IOUT = 1.0mA
–
0.02
0.1
%/V
Load Regulation (∆VOUT/∆IOUT)
VIN = VOUT-Nom+1.0V, IOUT = 1mA to 150mA
–
15
30
mV
–
35
50
µA
Quiescent Current (Note 6)
Set EN1 high, set EN2 low, or set EN2 high,
set EN1 low, No load
Set EN1/EN2 high, No load
–
70
100
µA
ISTANDBY
Set EN1/EN2 low, No load
–
0.1
1.0
µA
Output Current
–
300
–
–
mA
Fold-back Short Current (Note 7)
VOUT short to ground
–
55
–
mA
–
75
–
dB
–
60
–
µVrms
VOUT ≤ 1.2V
–
0.48
0.59
1.2V < VOUT ≤ 1.4V
–
0.39
0.50
1.4V < VOUT ≤ 1.7V
–
0.35
0.44
1.7V < VOUT ≤ 2.1V
–
0.30
0.39
2.1V < VOUT ≤ 2.5V
–
0.26
0.34
2.5V < VOUT ≤ 3.0V
–
0.25
0.30
3.0V < VOUT ≤ 3.6V
–
0.22
0.29
–
±30
–
ppm/°C
VIN = (VOUT+1V) VDC +
PSRR (Note 8)
0.2Vp-pAC,
f = 1kHz
VOUT ≥1.8V, IOUT = 30mA
Output Noise Voltage (Notes 8 & 9)
Dropout Voltage (Note 5)
Output Voltage Temperature Coefficient
BW = 10Hz to 100kHz, IOUT = 30mA
IOUT = 150mA
IOUT = 30mA, TA = -40°C to +85°C
V
EN Input Low Voltage
–
0
–
0.5
V
EN Input High Voltage
–
1.3
–
5.25
V
-1.0
–
1.0
µA
–
50
–
Ω
EN Input Leakage
VEN = 0V, VIN = 5.0V or VEN = 5.0V, VIN = 0V
On Resistance of N-Channel for AutoDischarge (Note 10)
VIN = 4.0V, VEN = 0V
Notes:
(Disabled)
D Version, Chanel 1 & 2
5. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.
6. Quiescent current is defined here is the difference in current between the input and the output.
7. Short circuit current is measured with VOUT pulled to GND.
8. This specification is guaranteed by design.
9. To make sure lowest environment noise minimizes the influence on noise measurement.
10. AP7342 has 2 options for output, built-in discharge and non-discharge
11. Potential multiple grades based on following output voltage accuracy.
AP7342
Document number: DS37614 Rev. 2 - 2
4 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Typical Characteristics
AP7342
Document number: DS37614 Rev. 2 - 2
5 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Typical Characteristics (cont.)
AP7342
Document number: DS37614 Rev. 2 - 2
6 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Typical Characteristic (cont.)
Load Transient Response Waveforms(VIN=VOUT+1V, CIN=COUT1=COUT2=0.47µ
µF, TA=25°C)
4
3
2
Input Voltage
1.82
Output Voltage
1.80
Input Voltage V IN (V)
Output Voltage V OUT (V)
1.8V
1.78
0
20
40
60
80
Time t (µs)
4
3
2
Input Voltage
Output Voltage
2.82
2.80
Input Voltage V IN (V)
Output Voltage V OUT (V)
2.8V
2.78
0
20
40
60
80
Time t (µs)
AP7342
Document number: DS37614 Rev. 2 - 2
7 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Typical Characteristics (cont.)
Load Transient Response Waveforms(VIN=VOUT+1V, CIN=COUT1=COUT2=0.47µF, TA = +25°C)
Output Voltage
3.4
3.3
Output Voltage Iout=30mA
80
160
240
320
Output Current
50mA ↔ 100mA
2.9
2.8
2.7
Output Voltage
3.2
400
0
80
160
320
Output Voltage V OUT (V)
Output Voltage V OUT (V)
Output Current I OUT (mA)
3.4
3.3
Output Voltage Iout=30mA
240
320
400
COUT=0.47µF
2.8V
200
100
0
Output Voltage
160
240
COUT=0.47µF
Output Current
0.1mA ↔ 150mA
80
2.9
Time t (µs)
1.8V
0
3.1
3.0
Output Voltage Iout=30mA
Time t (µs)
1.9
1.8
1.7
150
100
50
0
200
100
0
Output Current
0.1mA ↔ 150mA
2.9
2.8
2.7
Output Voltage
3.1
3.0
Output Voltage Iout=30mA
3.2
400
0
Time t (µs)
80
160
240
320
Output Current I OUT (mA)
0
Output Voltage V OUT (V)
1.9
1.8
1.7
Output Current I OUT (mA)
Output Voltage V OUT (V)
150
100
50
0
Output Current
50mA ↔ 100mA
COUT=0.47µF
2.8V
Output Current I OUT (mA)
COUT=0.47µF
1.8V
2.9
400
Time t (µs)
Turn On Waveform of Output Discharge versions (VIN=VOUT+1V, CIN=COUT1=COUT2=0.47µF, TA = +25°C)
AP7342
Document number: DS37614 Rev. 2 - 2
8 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Typical Characteristics (cont.)
Turn Off Waveform of Output Discharge versions (VIN=VOUT+1V, CIN=COUT1=COUT2=0.47µF, TA = +25°C)
2.8V
Output Voltage
IOUT=0mA
IOUT=30mA
IOUT=150mA
0
0
40
80
120
160
Output Voltage V OUT (V)
2
1
4
CE Input Voltage
3
2
1
0
CE Input Voltage V CE (V)
Output Voltage V OUT (V)
CE Input Voltage
2
0
4
2
Output Voltage
IOUT=0mA
IOUT=30mA
IOUT=150mA
0
200
0
Time t (µs)
40
80
120
160
CE Input Voltage V CE (V)
1.8V
200
Time t (µs)
Application Information
Output Capacitor
An output capacitor (COUT) is needed to improve transient response and maintain stability. The AP7342 is stable with very small ceramic output
capacitors. The ESR (Equivalent Series Resistance) and capacitance drives the selection. If the application has large load variations, it is
recommended to utilize low-ESR bulk capacitors. It is recommended to place ceramic capacitors as close as possible to the load and the GND pin
and care should be taken to reduce the impedance in the layout.
Input Capacitor
To prevent the input voltage from dropping during load steps, it is recommended to utilize an input capacitor (CIN). A minimum 0.47µF ceramic
capacitor is recommended between VIN and GND pin to decouple input power supply glitch. This input capacitor must be located as close as
possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both VIN and GND pin.
Enable Control
The AP7342 is turned on by setting the EN pins high, and is turned off by pulling it low. If this feature is not used, the EN pins should be tied to VIN
pin to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pins must be able to swing above
and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section.
Short Circuit Protection
When VOUT pins are short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 60mA. This feature
protects the regulator from overcurrent and damage due to overheating.
Layout Considerations
For good ground loop and stability, the input and output capacitors should be located close to the input, output, and GND pin of the device. The
regulator GND pin should be connected to the external circuit ground to reduce voltage drop caused by trace impedance. Ground plane is generally
used to reduce trace impedance. Wide trace should be used for large current paths from VIN to VOUT and load circuit.
AP7342
Document number: DS37614 Rev. 2 - 2
9 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
ESR vs. Output Current
Ceramic type output capacitor is recommended for this series; however, the other output capacitors with low ESR can also be used. The relations
between IOUT (Output Current) and ESR of an output capacitor are shown below. The stable region is marked as the hatched area in the graph.
Measurement Conditions: Frequency Band: 10Hz to 2MHz
2MHz, Temperature: −40°C to +85°C.
ESR vs. Output Current
AP7342-18
ESR vs. Output Current
AP7342-33
33
100
100
10
10
-40°C
85°C
ESR (Ω)
ESR (Ω)
1
0.1
0.01
-40°C
85°C
1
0.1
0.01
0.001
0.001
0
50
100
150
200
250
300
0
50
100
150
200
250
300
Output Current IOUT (mA)
Output Current IOUT (mA)
Ordering Information
–7
AP7342X XXXX FS6
Output Discharge
CH1/CH
CH2 Output Voltage
Blank : Non-discharge
CH1
1
CH2
D : Output Discharge
12 : 1.2
2V
15 : 1.5
5V
18 : 1.8
8V
25 : 2.5
5V
28 : 2.8
8V
30 : 3.0
0V
33 : 3.3
3V
36 : 3.6
6V
12 : 1.2V
15 : 1.5V
18 : 1.8V
25 : 2.5V
28 : 2.8V
30 : 3.0V
33 : 3.3V
Packaging
AP7342-XXXXFS6-7
FS6
AP7342D-XXXXFS6-7
FS6
AP7342
Document number: DS37614 Rev. 2 - 2
Packing
FS6 : X2-DFN1212-6
7 : Tape & Reel
7” Tape and Reel
Package
Code
Device
Package
Quantity
Part Number Suffix
X2-DFN1212-6
5,000/Tape & Reel
-7
X2-DFN1212-6
5,000/Tape & Reel
-7
10 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Marking Information
(1)
X2-DFN1212-6
Part Number
VOUT1/VOUT2
Package
Identification Code
AP7342-3028FS6-7
3.0V/2.8V
X2-DFN1212-6
CAA
AP7342-3328FS6-7
3.3V/2.8V
X2-DFN1212-6
CAB
AP7342D-1218FS6-7
1.2V/1.8V
X2-DFN1212-6
CAC
AP7342D-1528FS6-7
1.5V/2.8V
X2-DFN1212-6
CAD
AP7342D-1815FS6-7
1.8V/1.5V
X2-DFN1212-6
CAE
AP7342D-1818FS6-7
1.8V/1.8V
X2-DFN1212-6
CAF
AP7342D-1828FS6-7
1.8V/2.8V
X2-DFN1212-6
CAG
AP7342D-1833FS6-7
1.8V/3.3V
X2-DFN1212-6
CAH
AP7342D-2518FS6-7
2.5V/1.8V
X2-DFN1212-6
CAJ
AP7342D-2812FS6-7
2.8V/1.2V
X2-DFN1212-6
CAK
AP7342D-2818FS6-7
2.8V/1.8V
X2-DFN1212-6
CAM
AP7342D-2825FS6-7
2.8V/2.5V
X2-DFN1212-6
CAN
AP7342D-2833FS6-7
2.8V/3.3V
X2-DFN1212-6
CAP
AP7342D-3018FS6-7
3.0V/1.8V
X2-DFN1212-6
CAR
AP7342D-3028FS6-7
3.0V/2.8V
X2-DFN1212-6
CAS
AP7342D-3030FS6-7
3.0V/3.0V
X2-DFN1212-6
CAT
AP7342D-3318FS6-7
3.3V/1.8V
X2-DFN1212-6
CAU
AP7342D-3328FS6-7
3.3V/2.8V
X2-DFN1212-6
CAV
AP7342D-3330FS6-7
3.3V/3.0V
X2-DFN1212-6
CAW
AP7342D-3333FS6-7
3.3V/3.3V
X2-DFN1212-6
CAX
AP7342D-3612FS6-7
3.6V/1.2V
X2-DFN1212-6
CAY
AP7342
Document number: DS37614 Rev. 2 - 2
11 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Package Outline Dimensions (All dimensions in mm.)
Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version.
A3
A1
A
Seating Plane
D
Pin 1 ID C0.15
z1
D2
E2
k
E
L
X2-DFN1212-6
Dim Min
Max
Typ
A
0.40
0.39
A1
0.00
0.05 0.020
A3
0.13
b
0.13
0.23
0.18
D
1.15
1.25
1.20
D2
0.89
0.99
0.94
E
1.15
1.25
1.20
E2
0.25
0.35
0.30
e
0.40
k
0.15
0.25
0.20
L
0.15
0.25
0.20
z
0.11
z1
0.05
All Dimensions in mm
b
z
e
Suggested Pad Layout
Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version.
C
Y1
X2
Dimensions
X1
C
G
X
X1
X2
Y
Y1
Y2
G
Y2
Y
Value
(in mm)
0.400
0.150
0.250
0.940
1.050
0.400
0.300
1.400
X
AP7342
Document number: DS37614 Rev. 2 - 2
12 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
Tape Orientation
Note:
The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf.
AP7342
Document number: DS37614 Rev. 2 - 2
13 of 14
www.diodes.com
March 2015
© Diodes Incorporated
AP7342
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2015, Diodes Incorporated
www.diodes.com
AP7342
Document number: DS37614 Rev. 2 - 2
14 of 14
www.diodes.com
March 2015
© Diodes Incorporated