Download Datasheet

AZSR180
RoHS compliant !
80 A
POWER RELAY
FEATURES
•
•
•
•
•
•
•
•
•
80 Amp switching
Wide contact gap > 2.05mm
Holding power <100 mW
Dielectric strength 5000 Vrms
Isolation spacing greater than 10 mm
Double insulation, EN 60730-1 (VDE 0631, part 1)
Reinforced insulation, EN 60335-1 (VDE 0700, part 1)
UL, CUR E44211
VDE certificate 40044305
GENERAL DATA
CONTACTS
Arrangement
SPST (1 Form A)
Ratings
Resistive load:
Max.
Max.
Max.
Max.
switched power:
switched current:
continuous current:
switched voltage:
2400 W or 22160 VA
80 A (1000 cycles)
80 A
150 VDC* or 440 VAC
* Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
Rated Load
UL
VDE
Minimum operations
1 x 105
3 x 104 at 30 A 250 VAC Res.
Operate Time (typical)
40 ms at nominal coil voltage
Release Time (typical)
5 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
5000 Vrms coil to contact
(at sea level for 1 min.) 2500 Vrms between open contacts
Insulation
Resistance
1000 megohms min. at 20°C
500 VDC 50% RH
Insulation
(according to
DIN VDE 0110,
IEC 60664-1)
C250
Overvoltage category: III
Pollution degree: 3
Nominal voltage: 250 VAC
Dropout
Greater than 5% of nominal coil voltage
Ambient Temperature
Operating
At nominal coil voltage
-40°C (-40°F) to 85°C (185°F)
Vibration
0.062" (1.5 mm) DA at 10–55 Hz
Shock
10 g
Enclosure
PA
Terminals
Tinned copper alloy, P. C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Weight
105 grams
Packing unit in pcs
10 per inner carton / 100 per carton box
80 A at 277 VAC, resistive, 1k cycles
80 A at 277 VAC, resistive, 1k cycles, 85°C
30 A at 263 VAC, AC-7a, 30k cycles , 85°C
Material
Silver tin oxide
Resistance
< 50 milliohms initially
COIL
Power
At Pickup Voltage
(typical)
270 mW
Max. Continuous
Dissipation
2.0 W at 20°C (68°F) ambient
Temperature Rise
15°C (27°F) at nominal coil voltage
Temperature
Life Expectancy
Mechanical
Electrical
Max. 155°C (311°F) Class F
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
4. Recommended PCB cross section 16 mm².
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2016-06-27
AZSR180
RELAY ORDERING DATA
COIL SPECIFICATIONS - SPST (1 FORM A)
Nominal Coil
VDC
Must Operate
VDC
Min. Holding
VDC
Max. Continuous
VDC
Coil Resistance
Ohm ± 10%
ORDER NUMBER
12
9.00
4.0
24.0
300
AZSR180-1AE-12D
24
18.00
8.0
48.0
1200
AZSR180-1AE-24D
5
3.75
1.7
10.0
50
AZSR180-1AE-5D
9
6.75
3.1
18.0
170
AZSR180-1AE-9D
12
9.00
4.0
24.0
300
AZSR180-1AE-12D
18
13.50
6.5
36.0
675
AZSR180-1AE-18D
24
18.00
8.0
48.0
1200
AZSR180-1AE-24D
MECHANICAL DATA
PC BOARD LAYOUT
40.0
25.0
7.0 x 2.5 (4x)
3.3 x 1.3 (2x)
14.7
49.2
22.8
10.0
3.5
2.0
Viewed toward terminals
4.5
WIRING DIAGRAM
2,8 x 0,8 (2x)
6,5 x 2 (4x)
6
4
2
5
3
1
8.2 14.7
3.5
22.8
Viewed toward terminals
10.0
Viewed toward terminals
It is absolute necessary to provide a connection between pin 3
and 4 (5 and 6) on the PCB to avoid a malfunction of the relay!
Check also note 4 on first page, please.
Dimensions in mm. Tolerance: ± .25 mm
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2016-06-27
Similar pages