Data Sheet

UBA2035
HF full bridge control IC for HID lighting
Rev. 01 — 31 October 2008
Product data sheet
1. General description
The UBA2035 is a high voltage monolithic Integrated Circuit (IC) manufactured in a High
Voltage Silicon On Insulator (HVSOI) process. This circuit is designed for driving
MOSFETs in a full bridge configuration. In addition, it features a disable function, an
internal adjustable oscillator and an external clock input function with a high-voltage level
shifter for driving the bridge. To guarantee an accurate 50 % duty cycle, the oscillator
signal can be passed through a divider before being fed to the output drivers.
The UBA2035 is especially suitable for High Intensity Discharge (HID) lamp drivers for
projectors and general lighting applications for which a small non-overlap time is required.
2. Features
n
n
n
n
n
n
n
n
n
n
Full bridge driver circuit
Integrated bootstrap diodes
550 V series regulator input to make the internal supply
550 V maximum bridge voltage
Accurate bridge disable function
Input for start-up delay
Adjustable oscillator frequency
Selectable frequency divider
Predefined bridge position during start-up
A fixed non-overlap (< 200 ns)
3. Applications
n The UBA2035 can drive (via the power MOSFETs) any kind of load in a full bridge
configuration
n The circuit is especially designed as a commutator controller for high intensity
discharge lamps in projectors and general lighting applications
4. Ordering information
Table 1.
Ordering information
Type number
UBA2035TS
Package
Name
Description
Version
SSOP28
plastic shrink small outline package; 28 leads; body width 5.3 mm
SOT341-1
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
5. Block diagram
VSS(CLK) CLK
1
VDD(CLK)
3
2
16
FSL
HIGHER LEFT
DRIVER
15
GHL
6
HV
17
14
STABILIZER
SGND
VDD
RC
27
LOGIC SIGNAL
GENERATOR
9
13
HIGH VOLTAGE
LEVEL SHIFTER
HIGHER RIGHT
DRIVER
28
26
UBA2035TS
OSCILLATOR
LOWER RIGHT
DRIVER
÷2
23
21
SU
BD
10
12
LOW VOLTAGE
LEVEL SHIFTER
LOGIC
LOWER LEFT
DRIVER
20
SHL
FSR
GHR
SHR
GLR
PGND
GLL
1.29 V
bridge disable
11
DD
Fig 1.
4, 5, 7, 8, 18, 19, 22, 24, 25
n.c.
014aaa629
Block diagram
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
2 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
6. Pinning information
6.1 Pinning
VSS(CLK)
1
28 GHR
CLK
2
27 FSR
VDD(CLK)
3
26 SHR
n.c.
4
25 n.c.
n.c.
5
24 n.c.
HV
6
23 GLR
n.c.
7
n.c.
8
VDD
9
20 GLL
SU 10
19 n.c.
DD 11
18 n.c.
BD 12
17 SHL
RC 13
16 FSL
SGND 14
15 GHL
UBA2035TS
22 n.c.
21 PGND
014aaa630
Fig 2.
Pinning diagram
6.2 Pin description
Table 2.
Symbol
Pin description
Pin
UBA2035TS
Description
VSS(CLK)
1
negative supply voltage for logic oscillator input
CLK
2
oscillator input
VDD(CLK)
3
positive supply voltage for logic oscillator input
n.c.
4
not connected
n.c.
5
not connected
HV
6
high voltage supply input for internal series regulator
n.c.
7
not connected
n.c.
8
not connected
VDD
9
internal low voltage supply
SU
10
input for start-up delay
DD
11
input for divider disable
BD
12
input for bridge disable
RC
13
RC input for internal oscillator
SGND
14
signal ground
GHL
15
gate driver output for upper left MOSFET
FSL
16
floating supply left
SHL
17
source upper left MOSFET
n.c.
18
not connected
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
3 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
Table 2.
Pin description …continued
Symbol
Pin
UBA2035TS
Description
n.c.
19
not connected
GLL
20
gate driver output for lower left MOSFET
PGND
21
power ground
n.c.
22
not connected
GLR
23
gate driver output for lower right MOSFET
n.c.
24
not connected
n.c.
25
not connected
SHR
26
source upper right MOSFET
FSR
27
floating supply right
GHR
28
gate driver upper right MOSFET
7. Functional description
7.1 Supply voltage
The UBA2035 is powered by a supply voltage applied to pin HV, e.g., the supply voltage of
the full bridge. The IC generates its own low supply voltage for its internal circuitry.
Therefore an additional low voltage supply is not required. A capacitor has to be
connected to pin VDD to obtain a ripple-free internal supply voltage. The circuit can also
be powered by a low voltage supply directly applied to pin VDD. In this case pin HV should
be connected to pin VDD or pin SGND. The maximum current that the internal series
regulator can deliver, is temperature dependent. See Figure 3.
7.2 Start-up
With an increasing supply voltage the IC enters the start-up state i.e. the upper power
transistors are set in off-state and the lower power transistors are switched on. During the
start-up state the bootstrap capacitors are charged. The start-up state is defined until
VVDD = Vstartup(VDD) or VHV = Vstartup(HV). The state of the outputs during the start-up phase
is overruled by the bridge disable function.
7.3 Oscillation state
As soon as the supply voltage on pin VDD exceeds Vstartup(VDD) or the supply voltage on
pin HV exceeds Vstartup(HV), the output voltage of the full bridge depends on the control
signals on pins CLK, SU, DD and BD. This is listed in Table 3.
As soon as the supply voltage on pin VDD becomes lower than VUVLO(VDD) or the supply
voltage on pin HV becomes lower than VUVLO(HV), the IC enters the start-up state again.
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
4 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
Table 3.
Driver
Gate driver output voltages as function of the logical levels at the pins BD, SU, DD and CLK.
Device
state
BD
SU
DD
CLK
GHL
GHR
GLL
GLR
Start-up
state
1
-
-
-
0 (= VSHL)
0 (= VSHR)
0 (= VPGND)
0 (= VPGND)
0
-
-
-
0 (= VSHL)
0 (= VSHR)
1 (= VVDD)
1 (= VVDD)
1
-
-
-
0 (= VSHL)
0 (= VSHR)
0 (= VPGND) 0 (= VPGND)
0
0
-
-
0 (= VSHL)
0 (= VSHR)
1 (= VVDD)
1 (= VVDD)
0
1
1
1
0 (= VSHL)
1 (= VFSR)
1 (= VVDD)
0 (= VPGND)
0
1
1
0
1 (= VFSL)
0 (= VSHR)
0 (= VPGND) 1 (= VVDD)
1
0[1]
1→
GHL
GHR
GLL
Oscillation
state
0
0[2]
GLR
[1]
If pin DD = 0 the bridge enters the state (oscillation state and pin BD = 0 and pin SU = 1) in the predefined
position: VGHL = VFSL, VGLR = VVDD, VGLL = VPGND and VGHR = VSHR.
[2]
Only if the level of pin CLK changes from logical 1 to 0, the level of outputs GHL, GHR, GLL and GLR
changes.
If there is no external clock available, the internal oscillator can be used. The design
equation for the bridge oscillator frequency is shown in Equation 1.
1
f bridge = --------------------------------------------K osc × R osc × C osc
(1)
Rosc and Cosc are external components connected to the RC pin (Rosc connected to pin
VDD and Cosc connected to pin SGND). In this situation the pins VDD(CLK), CLK, and
VSS(CLK) can be connected to SGND.
The clock signal, either coming from pin RC or pin CLK, can be divided by two in order to
obtain a 50 % duty cycle gate drive signal. This can be achieved by applying a voltage to
the DD input lower than VIL(DD) (e.g. connect pin DD to pin SGND).
7.4 Non-overlap time
In the full bridge configuration the non-overlap time is defined as the time between turning
off the two conducting MOSFETs and turning on the two other MOSFETs. The (very
small) non-overlap time is internally fixed to tno, which allows a HID system to operate with
a very small phase angle between the load current and the full bridge voltage (pins SHL
and SHR). This can be beneficial for HID systems in which the lamp is ignited via a
resonance network.
7.5 Start-up delay
A simple resistor-capacitor (RC) filter (R between pin VDD and pin SU; C between pin SU
and pin SGND) or a control signal from a processor can be used to create a start-up
delay. This can be beneficial for those applications in which building up the high voltage
takes more time. A start-up delay will ensure that the HID system will not start up before
this high voltage has been reached.
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
5 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
7.6 Bridge disable
The bridge disable function can be used to switch off all MOSFETs as soon as the voltage
on pin BD exceeds the bridge disable voltage VBD. The bridge disable function overrules
all the other states.
8. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are measured with respect to signal
ground (pin 14); positive currents flow into the chip. The voltage ratings are valid provided other ratings are not violated.
Symbol
Parameter
Conditions
Min
Max
Unit
General
Tamb
ambient temperature
−40
+125
°C
Tj
junction temperature
−40
+150
°C
Tstg
storage temperature
−55
+150
°C
VVDD
voltage on pin VDD
0
14
V
VHV
voltage on pin HV
0
550
V
VSHL
voltage on pin SHL
with respect to PGND and SGND
−3
+550
V
VSHR
voltage on pin SHR
with respect to PGND and SGND
−3
+550
V
VFSL
voltage on pin FSL
with respect SHL
0
14
V
VFSR
voltage on pin FSR
with respect SHR
0
14
V
VGHL
voltage on pin GHL
VSHL
VFSL
V
VGHR
voltage on pin GHR
VSHR
VFSR
V
VGLL
voltage on pin GLL
VPGND
VVDD
V
VGLR
voltage on pin GLR
VPGND
VVDD
V
VPGND
voltage on pin PGND
0
5
V
Voltages
VSS(CLK)
CLK ground supply voltage
−0.9
14
V
VDD(CLK)
CLK supply voltage
with respect to VSS(CLK)
0
14
V
VI
input voltage
pin CLK; with respect to VSS(CLK)
0
14
V
pins RC, SU, BD, and DD
0
VVDD
V
slew rate
pins SHL and SHR
-
4
V/ns
oscillator resistance
connected between pins VDD and
RC
100
-
kΩ
electrostatic discharge voltage
human body model:
HV, VSS(CLK), VDD(CLK),CLK, FSL,
FSR, GHL, GHR, SHL, SHR
-
900
V
other pins
SR
Currents
Rosc
ESD
VESD
-
2
kV
machine model; all pins
-
200
V
charged device model; all pins
-
500
V
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
6 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
9. Thermal characteristics
Table 5.
Thermal characteristics
Symbol
Parameter
Conditions
Typ
Unit
Rth(j-a)
thermal resistance from
junction to ambient
in free air
100
K/W
10. Characteristics
Table 6.
Characteristics
Tj = 25 °C; all voltages are measured with respect to signal ground (pin 14); currents are positive when flowing into the IC,
unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
leakage current
pin HV;
IHV (VHV = 565 V) − IHV (VHV = 500 V)
-
-
5
µA
pin FSL; VFSL = VSHL = VGHL = 564 V
-
-
5
µA
pin FSR; VFSR = VSHR = VGHR = 564
V
-
-
5
µA
VHV = 80 V
-
590
825
µA
High voltage
Ileak
Start-up via HV pin
II(HV)
input current on pin HV
Vstartup(HV)
start-up voltage on pin HV
11.3
13.2
14.7
V
VUVLO(HV)
undervoltage lockout
voltage on pin HV
8.6
10.7
12.2
V
Vhys
hysteresis voltage
2
2.5
3
V
VVDD
voltage on pin VDD
10.5
12
13.5
V
VHV = 20 V
Start-up via VDD pin
II(VDD)
input current on pin VDD
-
500
800
µA
Vstartup(VDD)
start-up voltage on pin
VDD
8.25
9.0
9.75
V
VUVLO(VDD)
undervoltage lockout
voltage on pin VDD
5.75
6.5
7.25
V
Vhys
hysteresis voltage
2
2.5
3
V
GHR and GHL drivers;
VFSL = VFSR = 12 V;
VSHL = VSHR = 0 V;
IGHL = IGHR = −50 mA
-
20
42
Ω
GLR and GLL drivers; VVDD = 12 V;
VPGND = 0 V; IGLL = IGLR = −50 mA
-
20
42
Ω
GHR and GHL drivers;
VFSL = VFSR = 12 V;
VSHL = VSHR = 0 V;
IGHL = IGHR = 50 mA
-
12
26
Ω
GLR and GLL drivers; VVDD = 12 V;
VPGND= 0 V; IGLL = IGLR = 50 mA
-
12
26
Ω
VVDD = 8.25 V
gate drivers
Ron
Roff
on-state resistance
off-state resistance
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
7 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
Table 6.
Characteristics …continued
Tj = 25 °C; all voltages are measured with respect to signal ground (pin 14); currents are positive when flowing into the IC,
unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
IO(source)
output source current
VFSL = VFSR = VVDD = 12 V;
VSHL = VSHR = 0 V;
VGHL = VGHR = VGLL = VGLR = 8 V
-
200
-
mA
IO(sink)
output sink current
VFSL = VFSR = VVDD = 12 V;
VSHL = VSHR = 0 V;
VGHL = VGHR = VGLL = VGLR = 8 V
-
200
-
mA
Vd(bs)
bootstrap diode voltage
current on diode = 20 mA
-
2.3
-
V
tno
non-overlap time
-
80
250
ns
VUVLO
undervoltage lockout
voltage
high side driver
-
4.0
5.5
V
IFS
current on pin FS
VFSL = VFSR = 12 V;
VSHL = VSHR = 0 V
2
4
6
µA
VIH(DD)
HIGH-level input voltage
on pin DD
VVDD = 12 V
6
4.5
-
V
VIL(DD)
LOW-level input voltage on VVDD = 12 V
pin DD
-
-
3
V
II
input current
VVDD = 12 V
-
0
1
µA
Vstartup
start-up voltage
VVDD = 12 V
1
1.3
1.5
V
Vhys
hysteresis voltage
VVDD = 12 V
-
100
-
mV
II
input current
VVDD = 12 V
-
0
1
µA
VIH(CLK)
HIGH-level input voltage
on pin CLK
VSS(CLK) = 0 V; VDD(CLK) = 12 V
0.9
1.6
2.7
V
Vhys
hysteresis voltage
VSS(CLK) = 0 V; VDD(CLK) = 12 V
-
100
-
mV
II
input current
-
0
1
µA
fbridge
bridge frequency
-
-
250
kHz
DD input
SU input
CLK input
VRC = 0 V
supply for CLK
IDD(CLK)
CLK supply current
VSS(CLK) = 0 V; VDD(CLK) = 14 V
-
420
625
µA
VDD(CLK)
CLK supply voltage
VSS(CLK) = 0 V
5.75
-
14
V
BD input
VBD
voltage on pin BD
1.23
1.29
1.35
V
II
input current
-
0
1
µA
kHz
Internal oscillator
fosc(int)
internal oscillator
frequency
VCLK = 0 V; VSS(CLK) = 0 V
-
-
100
Kosc
oscillator constant
fbridge = 500 Hz
0.89
0.97
1.05
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
8 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
014aaa631
12
II(pin HV)
(µA)
8
(1)
(2)
4
(3)
0
0
200
400
600
VHV (V)
(1) Temperature = −25 °C
(2) Temperature = 25 °C
(3) Temperature = 125 °C
Fig 3.
Typical II (pin HV) when VDD connected to SGND, as function of VHV and temperature
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
9 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
11. Package outline
SSOP28: plastic shrink small outline package; 28 leads; body width 5.3 mm
D
SOT341-1
E
A
X
c
HE
y
v M A
Z
28
15
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
14
w M
bp
e
detail X
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
2
0.21
0.05
1.80
1.65
0.25
0.38
0.25
0.20
0.09
10.4
10.0
5.4
5.2
0.65
7.9
7.6
1.25
1.03
0.63
0.9
0.7
0.2
0.13
0.1
1.1
0.7
8
o
0
o
Note
1. Plastic or metal protrusions of 0.2 mm maximum per side are not included.
OUTLINE
VERSION
SOT341-1
Fig 4.
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
MO-150
Package outline SSOP28 (SOT341-1)
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
10 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
12. Revision history
Table 7.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
UBA2035_1
20081031
Product data sheet
-
-
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
11 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
13. Legal information
13.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
13.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
13.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
13.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
14. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
UBA2035_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 31 October 2008
12 of 13
UBA2035
NXP Semiconductors
HF Full bridge control IC for HID lighting
15. Contents
1
2
3
4
5
6
6.1
6.2
7
7.1
7.2
7.3
7.4
7.5
7.6
8
9
10
11
12
13
13.1
13.2
13.3
13.4
14
15
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . 4
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . 4
Start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Oscillation state . . . . . . . . . . . . . . . . . . . . . . . . 4
Non-overlap time . . . . . . . . . . . . . . . . . . . . . . . 5
Start-up delay . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Bridge disable . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Thermal characteristics. . . . . . . . . . . . . . . . . . . 7
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 11
Legal information. . . . . . . . . . . . . . . . . . . . . . . 12
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 12
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Contact information. . . . . . . . . . . . . . . . . . . . . 12
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 31 October 2008
Document identifier: UBA2035_1
Similar pages