Over Voltage Protection IC (6.85 V Threshold)

NCP345
Overvoltage Protection IC
The NCP345 overvoltage protection circuit (OVP) protects
sensitive electronic circuitry from overvoltage transients and power
supply faults when used in conjunction with an external P−channel
FET. The device is designed to sense an overvoltage condition and
quickly disconnect the input voltage supply from the load before any
damage can occur. The OVP consists of a precise voltage reference, a
comparator with hysteresis, control logic, and a MOSFET gate driver.
The OVP is designed on a robust BiCMOS process and is intended to
withstand voltage transients up to 30 V.
The device is optimized for applications that have an external
AC/DC adapter or car accessory charger to power the product and/or
recharge the internal batteries. The nominal overvoltage threshold is
6.85 V so it is suitable for single cell Li−Ion applications as well as 3/4
cell NiCD/NiMH applications.
http://onsemi.com
1
PIN CONNECTIONS &
MARKING DIAGRAM
Overvoltage Turn−Off Time of less than 1.0 msec
Accurate Voltage Threshold of 6.85 V (nominal)
Undervoltage Lockout Protection
CNTRL Input Compatible with 1.8 V Logic Levels
Pb−Free Package is Available
GND
2
CNTRL
3
5
VCC
4
IN
(Top View)
RAD = Specific Device Code
A
= Assembly Location
Y
= Year
W = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
Typical Applications
•
•
•
•
RADAYWG
G
OUT 1
Features
•
•
•
•
•
THIN SOT−23−5
SN SUFFIX
CASE 483
5
Cellular Phones
Digital Cameras
Portable Computers and PDAs
Portable CD and other Consumer Electronics
ORDERING INFORMATION
Device
Shipping †
Package
NCP345SNT1
SOT−23−5
NCP345SNT1G
SOT−23−5
(Pb−Free)
3000 / Tape &
Reel
(7 inch Reel)
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
P−CH
AC/DC Adapter or
Accessory Charger
Schottky
Diode
VCC
IN
Undervoltage
Lock Out
+
−
+
Logic
FET
Driver
C1
LOAD
OUT
Vref
NCP345
GND
CNTRL
Microprocessor port
Note: This device contains 89 active transistors
Figure 1. Simplified Application Diagram
© Semiconductor Components Industries, LLC, 2006
March, 2006 − Rev. 6
1
Publication Order Number:
NCP345/D
NCP345
VCC
(5)
IN
(4)
VCC
V5
Pre−
regulator
R1
R3
+
COMP
−
+
UVLO
−
R2
VCC
LOGIC
BLOCK
ON/OFF
OUT
OUT
(1)
DRIVER
R4
Bandgap
Reference
CNTRL
(3)
GND
(2)
Figure 2. Detailed Block Diagram
PIN FUNCTION DESCRIPTIONS
Pin #
Symbol
Pin Description
1
OUT
This signal drives the gate of a P−channel MOSFET. It is controlled by the voltage level on IN or the logic state
of the CNTRL input. When an overvoltage event is detected, the OUT pin is driven to within 1.0 V of VCC in
less than 1.0 msec provided that gate and stray capacitance is less than 12 nF.
2
GND
Circuit Ground
3
CNTRL
4
IN
5
VCC
This logic signal is used to control the state of OUT and turn−on/off the P−channel MOSFET. A logic High
results in the OUT signal being driven to within 1.0 V of VCC which disconnects the FET. If this pin is not used,
the input should be connected to ground.
This pin senses an external voltage point. If the voltage on this input rises above the overvoltage threshold
(VTH), the OUT pin will be driven to within 1.0 V of VCC, thus disconnecting the FET. The nominal threshold
level is 6.85 V and this threshold level can be increased with the addition of an external resistor between IN
and VCC.
Positive Voltage supply. If VCC falls below 2.8 V (nom), the OUT pin will be driven to within 1.0 V of VCC, thus
disconnecting the P−channel FET.
TRUTH TABLE
IN
CNTRL
OUT
<Vth
L
GND
<Vth
H
VCC
>Vth
L
VCC
>Vth
H
VCC
http://onsemi.com
2
NCP345
ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise noted.)
Rating
Pin
Symbol
Min
Max
Unit
OUT voltage to GND
1
VO
−0.3
30
V
Input and CNTRL pin voltage to GND
4
3
Vinput
VCNTRL
−0.3
−0.3
30
13
V
VCC Maximum Range
5
VCC(max)
−0.3
30
V
Maximum Power Dissipation at TA = 85°C
−
PD
−
0.216
W
Thermal Resistance Junction to Air
−
RqJA
−
300
°C/W
Junction Temperature
−
TJ
−
150
°C
Operating Ambient Temperature
−
TA
−40
85
°C
VCNTRL Operating Voltage
3
−
0
5.0
V
Storage Temperature Range
−
Tstg
−65
150
°C
ESD performance (HBM){
all
−
2.5
−
kV
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
{ Human body model (HBM): MIL STD 883C Method 3015−7, (R = 1500 ohms, C = 100 pf, F = 3 pulses delay 1 s).
ELECTRICAL CHARACTERISTICS
(For typical values TA = 25°C, for min/max values TA = −40°C to +85°C, VCC = 6.0 V, unless otherwise noted.)
Characteristic
VCC Operating Voltage Range
Supply Current (ICC + IInput; VCC = 6.0 V Steady State)
Input Threshold
(VInput connected to VCC; VInput increasing)
Input Hysteresis (VInput connected to VCC; VInput decreasing)
Symbol
Pin
Min
Typ
Max
Unit
VCC(opt)
5
3.0
4.8
25
V
−
4,5
−
0.75
1.0
mA
VTh
4
6.65
6.85
7.08
V
VHyst
4
50
100
200
mV
Input Impedance (Input = VTh)
Rin
4
70
150
−
kW
CNTRL Voltage High
Vih
3
1.5
−
−
V
CNTRL Voltage Low
Vil
3
−
−
0.5
V
CNTRL Current High (Vih = 5.0 V)
Iih
3
−
95
200
mA
CNTRL Current Low (Vil = 0.5 V)
Iil
3
−
10
20
mA
Undervoltage Lockout (VCC decreasing)
VLock
3
2.5
2.8
3.0
V
Output Sink Current (VCC < VTh, VOUT = 1.0 V)
ISink
1
10
33
50
mA
Output Voltage High (VCC = Vin = 8.0 V; ISource = 10 mA)
Output Voltage High (VCC = Vin = 8.0 V; ISource = 0.25 mA)
Output Voltage High (VCC = Vin = 8.0 V; ISource = 0 mA)
Voh
1
VCC−1.0
VCC−0.25
VCC−0.1
−
−
−
−
V
Output Voltage Low
(Input < 6.5 V; ISink = 0 mA; VCC = 6.0 V, CNTRL = 0 V)
Vol
1
−
−
0.1
V
Turn ON Delay − Input (VInput connected to VCC; VInput step down
signal from 8.0 to 6.0 V; measured to 50% point of OUT)*
TON IN
1
−
−
10
msec
Turn OFF Delay − Input (VInput connected to VCC; VInput step up signal
from 6.0 to 8.0 V; CL = 12 nF Output > VCC−1.0 V)
TOFF IN
1
−
0.5
1.0
msec
Turn ON Delay − CNTRL (CNTRL step down signal from 2.0 to 0.5 V;
measured to 50% point of OUT)*
TON CT
1
−
−
10
msec
Turn OFF Delay − CNTRL (CNTRL step up signal from 0.5 to 2.0 V;
CL = 12 nF Output > VCC−1.0 V)
TOFF CT
1
−
1.0
2.0
msec
*Turn ON Delay is guaranteed by design.
http://onsemi.com
3
7.05
50
7.00
45
6.95
40
Sink Current (mA)
Voltage (V)
NCP345
6.90
6.85
6.80
30
25
20
6.75
6.70
−40
35
15
−25
−10
5
20
35
50
65
80
10
−40
95
−25
−10
Ambient Temperature (°C)
5
20
35
50
65
80
95
Ambient Temperature (°C)
Figure 3. Typical Vth Threshold Variation vs.
Temperature
Figure 4. Typical OUT Sink Current vs. Temperature
Vin t Vth, Vout + 1 V
1.0
I supply (mA)
0.9
0.8
0.7
0.6
0.5
−40
−25
−10
5
20
35
50
65
80
95
Temperature (°C)
Figure 5. Typical Supply Current vs. Temperature
Icc ) Iin, VCC + 6 V
2
VLOAD = 50 W
MOSFET = MGSF3441
2
CNTRL
1
1
0
Voltage (V)
Voltage (V)
CNTRL
6
VLOAD
4
2
VLOAD = 50 W
MOSFET = MGSF3441
0
6
VLOAD
4
2
0
0
T = 25°C
50
T = 25°C
100 150 200 250 300 350 400 450 500
5
Time (nsec)
10
15
20
25
30
35
40
45
50
Time (msec)
Figure 6. Typical Turn−off Time CNTRL to VLOAD
Figure 7. Typical Turn−on Time CNTRL to VLOAD
http://onsemi.com
4
NCP345
APPLICATION INFORMATION
P−CH
AC/DC Adapter or
Accessory Charger
Schottky
Diode
VCC
IN
Undervoltage
Lock Out
+
−
Zener
Diode
(optional)
FET
Driver
Logic
Zener
Diode
OUT (optional)
+
C1
LOAD
Vref
NCP345
GND
CNTRL
Microprocessor
port
Figure 8.
Introduction
voltage by analyzing the dV/dT rise that occurs during the
brief time it takes to turn−off the MOSFET. For battery
powered applications, a low−forward voltage Schottky
diode such as the MBRM120LT3 can be placed in series
with the MOSFET to block the body diode of the MOSFET
and prevent shorting the battery out if the input is
accidentally shorted to ground. This provides additional
voltage margin at the load since there is a small forward drop
across this diode that reduces the voltage at the load.
When the protection circuit turns off the MOSFET, there
can be a sudden rise in the input voltage of the device. This
transient can be quite large depending on the impedance of
the supply and the current being drawn from the supply at the
time of an overvoltage event. This inductive spike can be
clamped with a zener diode from IN to ground. This diode
breakdown voltage should be well above the worst case
supply voltage provided from the AC/DC adapter or
Cigarette Lighter Adapter (CLA), since the zener is only
intended to clamp the transient. The NCP345 is designed so
that the IN and VCC pin can safely protect up to 25 V and
withstand transients to 30 V. Since these spikes can be very
narrow in duration, it is important to use a high bandwidth
probe and oscilloscope when prototyping the product to
verify the operation of the circuit under all the transient
conditions. A similar problem can result due to contact
bounce as the DC source is plugged into the product.
For portable products it is normal to have a capacitor to
ground in parallel with the battery. If the product has a
battery pack that is easily removable during charging, this
scenario should be analyzed. Under that situation, the
charging current will go into the capacitor and the voltage
may rise rapidly depending on the capacitor value, the
charging current and the power supply response time.
In many electronic products, an external AC/DC wall
adapter is used to convert the AC line voltage into a
regulated DC voltage or a current limited source. Line
surges or faults in the adapter may result in overvoltage
events that can damage sensitive electronic components
within the product. This is becoming more critical as the
operating voltages of many integrated circuits have been
lowered due to advances in sub−micron silicon lithography.
In addition, portable products with removable battery packs
pose special problems since the pack can be removed at any
time. If the user removes a pack in the middle of charging,
a large transient voltage spike can occur which can damage
the product. Finally, damage can result if the user plugs in
the wrong adapter into the charging jack. The challenge of
the product designer is to improve the robustness of the
design and avoid situations where the product can be
damaged due to un−expected, but unfortunately, likely
events that will occur as the product is used.
Circuit Overview
To address these problems, the protection system above
has been developed consisting of the NCP345 Over Voltage
Protection IC and a P−channel MOSFET switch such as the
MGSF3441. The NCP345 monitors the input voltage and
will not turn on the MOSFET unless the input voltage is
within a safe operating window that has an upper limit of
7.05 V. A zener diode can be placed in parallel to the load to
provide for secondary protection during the brief time that
it takes for the NCP345 to detect the overvoltage fault and
disconnect the MOSFET. The decision to use this secondary
diode is a function of the charging currents expected, load
capacitance across the battery, and the desired protection
http://onsemi.com
5
NCP345
Normal Operation
performance is illustrated using the MGSF3441 in Figure 7.
This characteristic is a function of the threshold of the
MOSFET and will vary depending on the device
characteristics such as the gate capacitance.
The OVP has an under voltage lockout (UVLO) circuit
which disables the gate driver circuit until the UVLO senses
that the VCC voltage is above 2.6 V. Once the UVLO has
released the gate driver circuit, the OUT signal will stay high
until the voltage on the IN is sensed. If the input voltage to
IN is less than 6.85 V nominal, then the OUT signal will be
driven LOW and the FET will be turned on so the source can
be connected to the load.
There are three events that will cause the OVP to drive the
gate of the FET to a HIGH state.
• Voltage on VCC falls below the UVLO threshold
• Voltage on IN rises above 6.85 V (nominal)
• CNTRL input is driven to a logic High
Figure 1 illustrates a typical configuration. The external
adapter provides power to the protection system so the
circuitry is only active when the adapter is connected. The
OVP monitors the voltage from the charger and if the
voltage exceeds a nominal voltage of 6.85 V, the OUT signal
drives the gate of the MOSFET to within 1.0 V of VCC, thus
turning off the FET and disconnecting the source from the
load. The nominal time it takes to drive the gate to this state
is 400 nsec (1.0 usec maximum for gate capacitance of
< 12 nF). Typical turn off performance using the CNTRL
input can be seen in Figure 6. The CNTRL input can also be
used to interrupt charging and allow the microcontroller to
measure the cell voltage under a normal condition to get a
more accurate measure of the battery voltage. Once the over
voltage is removed, the NCP345 will turn on the MOSFET.
The turn on circuitry is designed to turn on the MOSFET
more gradually to limit the in−rush current. Typical turn−on
http://onsemi.com
6
NCP345
PACKAGE DIMENSIONS
THIN SOT−23−5
SN SUFFIX
CASE 483−02
ISSUE E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. A AND B DIMENSIONS DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
D
S
5
4
1
2
3
B
L
G
DIM
A
B
C
D
G
H
J
K
L
M
S
A
J
C
0.05 (0.002)
H
M
K
MILLIMETERS
MIN
MAX
2.90
3.10
1.30
1.70
0.90
1.10
0.25
0.50
0.85
1.05
0.013
0.100
0.10
0.26
0.20
0.60
1.25
1.55
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
7
INCHES
MIN
MAX
0.1142 0.1220
0.0512 0.0669
0.0354 0.0433
0.0098 0.0197
0.0335 0.0413
0.0005 0.0040
0.0040 0.0102
0.0079 0.0236
0.0493 0.0610
0_
10 _
0.0985 0.1181
NCP345
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
8
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
NCP345/D