NCV8613B Ultra-Low Iq Automotive System Power Supply IC Power Saving Triple-Output Linear Regulator The NCV8613B is a multiple output linear regulator IC’s with an Automatic Switchover (ASO) input voltage selector. The ASO circuit selects between three different input voltage sources to reduce power dissipation and to maintain the output voltage level across varying battery line voltages associated with an automotive environment. The NCV8613B is specifically designed to address automotive radio systems and instrument cluster power supply requirements. The NCV8613B can be used in combination with the 4−Output Controller/Regulator IC, NCV885x, to form a complete automotive radio or instrument cluster power solution. The NCV8613B is intended to supply power to various “always on” loads such as the CAN transceivers and microcontrollers (core, memory and IO). The NCV8613B has three output voltages, a reset / delay circuit, and a host of control features suitable for the automotive radio and instrument cluster systems. http://onsemi.com MARKING DIAGRAM 20 NCV8613B AWLYYWWG G 1 DFN20 MN SUFFIX CASE 505AB A WL YY WW G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) Features • • • • • • • • • • • • • Operating Range 7.0 V to 18.0 V (45 V Load Dump Tolerant) Output Voltage Tolerance, All Rails, $2% < 50 mA Quiescent Current Independent Input for LDO3 Linear Regulator High Voltage Ignition Buffer Automatic Switchover Input Voltage Selector Independent Input Voltage Monitor with a High Input Voltage and Low Input Voltage (Brown−out) Indicators Thermal Warning Indicator with Thermal Shutdown Single Reset with Externally Adjustable Delay for the 3.3 V Rail Push−Pull Outputs for Logic Level Control Signals All Ceramic Solution for Reduced Leakage Current at the Output NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes This is a Pb−Free Device • Automotive Radio • Instrument Cluster March, 2010 − Rev. 0 ASO_RAIL VIN_S3 VIN−B VOUT3 VIN−H VOUT2 VIN−A VOUT1 VBATT_MON VPP HV_DET RST BO_DET DLY NC GND GND IGNOUT IGNIN HOT_FLG ORDERING INFORMATION Device NCV8613BMNR2G Applications © Semiconductor Components Industries, LLC, 2010 PIN CONNECTIONS Package Shipping† DFN20 2500 / Tape & Reel (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. 1 Publication Order Number: NCV8613B/D NCV8613B NC 8 D2 8V ASO_RAIL 1 1 uF VIN-B 20 VINT 2 VBATT D1 VTH1 VTH2 1 uF VIN-H ILIMIT VBG VREF OVS VBATT_MON 5 VREF VIN_MON VPP VPP 7 VRTH 17 VREF VRFB1 TSD 16 TSD 15 11 D3 IGNOUT 5V Fault Logic VTH2 10 IGNIN VOUT1 ILIMIT VIN_MON VPP HOT_FLG RST2 OVS 3.3 V VPP VRFB2 VTH1 6 VOUT2 ILIMIT Switchover Control Circuit HV_DET BO_DET VRFB3 18 4 3.3 V VREF 3 1000 uF VIN-A 19 VIN_S3 VOUT3 VPP RST HV_DET 14 12 10 kΩ 9 13 GND + 5V GND Components Value Manufacturer D1 MBRS2H100T3G ON Semiconductor D2 MBR130T1 ON Semiconductor D3 MMDL914T1 ON Semiconductor Figure 1. Typical Circuit with the Internal Schematic http://onsemi.com 2 DLY NCV8613B PIN FUNCTION DESCRIPTIONS Pin No. Symbol 1 ASO_RAIL Description Output/Input of the automatic switchover (ASO) circuitry. Place a 1 uF ceramic capacitor on this pin to provide local bypassing to the LDO linear regulator pass devices. 2 VIN−B Primary power supply input. Connect battery to this pin through a blocking diode. 3 VIN−H Holdup power supply rail. Connect a storage capacitor to this pin to provide a temporary backup rail during loss of battery supply. A bleed resistor (typically 1 kW) is needed from VIN−B to this pin in order to trickle charge this capacitor. 4 VIN−A Voltage monitor which determines whether the 8 V supply is able to power the outputs. If the 8 V supply is present, the FET’s connected to VIN−B and VIN−H will be turned off, and the 8 V supply will be providing power to the outputs. If the 8 V supply is not present, the FET’s on VIN−B and VIN−H will be left on, and the greater of those voltages will be driving the outputs. 5 VBATT_MON VBATT monitor pin. To operate overvoltage shutdown, HV_DET and BO_DET, connect this pin to ASO_RAIL or battery. To eliminate overvoltage shutdown, HV_DET and BO_DET, tie this pin to ground. 6 HV_DET High−voltage detect output. When VBATT_MON surpasses 17 V, this pin will be driven to ground. During normal operation, this pin is held at VPP. 7 BO_DET Brown out indicator output. When VBATT_MON and VIN−A falls below 7.5 V, this pin will be driven to ground. During normal operation, this pin is held at VPP. 8 NC 9 GND 10 HOT_FLG No Connect Ground. Reference point for internal signals. Internally connected to pin 13. Ground is not connected to the exposed pad of the DFN20 package. Thermal warning indicator. This pin provides an early warning signal of an impending thermal shutdown. 11 IGNIN Ignition buffer input 12 IGOUT Ignition buffer logic output 13 GND Ground. Reference point for internal signals. Internally connected to pin 9. Ground is not connected to the exposed pad of the DFN20 package. 14 DLY Delay pin. Connect a capacitor to this pin to set the delay time. 15 RST Reset pin. Monitors VOUT1. 16 VPP Supply rail for the push−pull outputs of the control signals HOT_FLG, RST, HV_DET & BO_DET 17 VOUT1 5 V output. Voltage is internally set. 18 VOUT2 3.3 V output. Voltage is internally set. 19 VOUT3 3.3 V output. Voltage is internally set. 20 VIN_S3 EP − Supply rail for the standby linear regulator VOUT3. Tie this pin to ASO_RAIL or a separate supply rail. Exposed Pad of DFN device. This pad serves as the main path for thermal spreading. The Exposed Pad is not connected to IC ground. http://onsemi.com 3 NCV8613B MAXIMUM RATINGS (Voltages are with respects to GND unless noted otherwise) Rating Symbol Max Min Unit Maximum DC Voltage VIN−B, VIN−A, ASO_RAIL, VBATT_MON, VIN_S3, EN, IGNIN 40 −0.3 V Peak Transient VIN−B, VIN−A, ASO_RAIL, VBATT_MON, VIN_S3, EN, IGNIN 45 −0.3 V Maximum DC Voltage VIN−H 24 −0.3 V Maximum DC Voltage IGNOUT, VPP, HV_DET, BO_DET, HOT_FLG, RST, DLY, VOUT1, VOUT2, VOUT3 7 −0.3 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. THERMAL INFORMATION Rating Symbol Min Unit RqJA 40 °C/W Operating Junction Temperature Range TJ −40 to 150 °C Maximum Storage Temperature Range TSTG −55 to +150 °C Moisture Sensitivity Level MSL 1 Thermal Characteristic (Note 1) 1. Values based on measurement of NCV8613B assembled on 2−layer 1−oz Cu thickness PCB with Copper Area of more than 645 mm2 with several thermal vias for improved thermal performance. Refer to CIRCUIT DESCRIPTION section for safe operating area. ATTRIBUTES Rating Symbol Min Unit ESDHB 2 kV ESD Capability, Machine Model (Note 2) ESDMM 200 V ESD Capability, Charged Device Model (Note 2) ESDCDM 1 kV IGNIN ESD Capability, Human Body Model (Note 2) ESDHB_IGNIN 3 kV IGNIN ESD Capability, Machine Model (Note 2) ESDMM_IGNIN 200 V ESD_IGNIN 10 kV ESD Capability, Human Body Model (Note 2) IGNIN ESD Capability (Note 3) 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model (HBM) tested per AEC−Q100−002 (EIA/JESD22−A114) ESD Machine Model (MM) tested per AEC−Q100−003 (EIA/JESD22−A115) ESD Charged Device Model (CDM) tested per EIA/JES D22/C101, Field Induced Charge Model 3. Device tested with external 10 kW series resistance and 1 nF storage capacitor. http://onsemi.com 4 NCV8613B SUPPLY VOLTAGES AND SYSTEM SPECIFICATION ELECTRICAL CHARACTERISTICS (7 V < ASO_RAIL < 18 V, VIN−H = VIN−B w ASO_RAIL, VPP = 5 V, VIN_S3 tied to ASO_RAIL, VBATT_MON = 0 V, IGNIN = 0 V, ISYS = 3 mA (Note 6)) Minimum/Maximum values are valid for the temperature range −40°C v TJ v 150°C unless noted otherwise. Min/Max values are guaranteed by test, design or statistical correlation. Parameter Symbol Conditions Min Typ Max Unit 34 50 mA SUPPLY RAILS Quiescent Current (Notes 4 and 6) iq TJ = 25°C, ISYS = 70 mA, VIN−A = VIN_S3 = 0 V, VIN−B = 13.2 V Minimum Operating Voltage (VIN−H, VIN−B) 4.5 V THERMAL MONITORING Thermal Warning (HOT_FLG) Temperature TWARN 140 TWARN Hysteresis 10 Thermal Shutdown 160 Thermal Shutdown Hysteresis 10 Delta Junction Temperature (TSD − TWARN) 10 HOT_FLG Voltage Low TJ < TWARN, 10 kW Pullup to 3.3 V HOT_FLG Voltage High TJ > TWARN, 10 kW Pulldown to GND 150 170 20 160 °C 20 °C 180 °C 20 °C 30 °C 0.4 V VPP−0.5 V AUTO SWITCHOVER VIN−A Quiescent Current 24 mA VIN−A to VIN−B Risetime TJ = 25°C, CASO_RAIL = 1 mF, ISYS = 400 mA 200 msec VIN−B to VIN−A Falltime TJ = 25 °C, CASO_RAIL = 1 mF, ISYS = 400 mA 100 msec VIN−A Operating Threshold VIN−A Rising 7.2 7.5 7.75 V VIN−A Operating Hysteresis VIN−A Falling 100 175 250 mV Max VIN−B to VASO_RAIL Voltage Drop ISYS = 400 mA, VIN−B = 7 V 1.5 V Max VIN−H to VASO_RAIL Voltage Drop ISYS = 400 mA, VIN−H = 7.5 V 2.0 V 96 % 2.5 % RESET (RST Pin) RESET Threshold % of VOUT2 90 Hysteresis % of VOUT2 Reset Voltage High 10 kW Pulldown to GND Reset Voltage Low 10 kW Pullup to 3.3 V 93 VPP−0.5 V 0.4 V 7 mA DELAY (DLY Pin) 2.4 Charge Current Delay Trip Point Voltage 5 2.0 V IGNITION BUFFER Schmitt Trigger Rising Threshold 2.75 3.25 3.75 V Schmitt Trigger Falling Threshold 0.8 1.0 1.2 V IGNOUT Voltage Low IGNIN = 5 V, 10 kW Pullup to 5 V IGNOUT Leakage Current TJ = 25°C, IGNOUT = 5 V 0.4 V 0.1 0.5 mA 3 5 mA 2.0 2.5 V VBATT MONITOR VBATT_MON Quiescent Current TJ = 25°C, VBATT_MON = 13.2 V VBATT_MON Minimum Operating Voltage Threshold where BO_DET and HV_DET signals become valid http://onsemi.com 5 1.0 NCV8613B SUPPLY VOLTAGES AND SYSTEM SPECIFICATION ELECTRICAL CHARACTERISTICS (7 V < ASO_RAIL < 18 V, VIN−H = VIN−B w ASO_RAIL, VPP = 5 V, VIN_S3 tied to ASO_RAIL, VBATT_MON = 0 V, IGNIN = 0 V, ISYS = 3 mA (Note 6)) Minimum/Maximum values are valid for the temperature range −40°C v TJ v 150°C unless noted otherwise. Min/Max values are guaranteed by test, design or statistical correlation. Parameter Symbol Conditions Min Typ Max Unit VBATT MONITOR VBATT_MON Hysteresis 0.25 HV_DET Voltage High 10 kW Pulldown to GND VBATT_MON Tied to ASO_RAIL HV_DET Voltage Low 10 kW Pullup to 3.3 V VBATT_MON Tied to ASO_RAIL HV_DET Threshold VBATT_MON Rising 16.2 HV_DET Hysteresis VBATT_MON Falling 0.2 BO_DET Voltage High 10 kW Pulldown to GND VBATT_MON Tied to ASO_RAIL BO_DET Voltage Low 10 kW Pullup to 3.3 V VBATT_MON Tied to ASO_RAIL BO_DET Threshold VBATT_MON Falling 7 BO_DET Hysteresis VBATT_MON Rising V VPP−0.5 V 0.35 0.4 V 17.8 V 0.5 V VPP−0.5 V 0.4 V 7.5 8 V 0.2 0.35 0.5 V 3 5 6 V 0.1 0.5 mA VPP PIN VPP Voltage Range Leakage Current 4. 5. 6. TJ = 25°C iq is equal to IVIN−B + IVIN−H − ISYS ISHDN is equal to IVIN−B + IVIN−H ISYS is equal to IOUT1 + IOUT2 + IOUT3 http://onsemi.com 6 NCV8613B ELECTRICAL CHARACTERISTICS (7 V < ASO_RAIL < 18 V, VIN−H = VIN−B w ASO_RAIL, VPP = 5 V, VIN_S3 tied to ASO_RAIL, VBATT_MON = 0 V, IGNIN = 0 V, ISYS = 3 mA (Note 6)) Min/Max values are valid for the temperature range −40°C vTJ v 150 °C unless noted otherwise. Min/Max values are guaranteed by test, design or statistical correlation. Parameter Symbol Conditions Min Typ Max Unit 4.9 5 5.1 V 500 mV LOW DROP−OUT LINEAR REGULATOR 1 (LDO1) SPECIFICATION Output Voltage Dropout (ASO_RAIL − VOUT1) IOUT1 = 0 mA to 100 mA, 7 V < ASO_RAIL < 18 V VDR1 IOUT1 = 100 mA (Note 7) Load Regulation IOUT1 = 0 mA to 100 mA, VIN_B = 13.2 V 0 75 mV/mA Line Regulation IOUT1 = 1 mA, 7 V < ASO_RAIL < 18 V 0 2 mV/V Output Current Limit Output Load Capacitance Range Output Load Capacitance ESR Range (Notes 8 and 9) 200 Co ESRCo mA Output Capacitance for Stability 1.0 100 mF Cap ESR for Stability 0.01 13 W DVOUT1 (ASO Low to High Transient) TJ = 25 °C , IOUT1 = 100 mA, ISYS = 400 mA, CASO_RAIL = 1 mF, ESRCo = 0.01 W, Co = 10 mF, VIN−A falling 70 100 $mV DVOUT1 (ASO high to Low Transient) TJ = 25 °C , IOUT1 = 100 mA, ISYS = 400 mA, CASO_RAIL = 1 mF, ESRCo = 0.01 W, Co = 10 mF, VIN−A rising 70 100 $mV VIN_B = 13.2 V, 0.5 VPP, 100 Hz 60 Power Supply Ripple Rejection (Note 8) PSRR Startup Overshoot IOUT1 = 0 mA to 100 mA dB 3 % 3.366 V 1.5 V LOW DROP−OUT LINEAR REGULATOR 2 (LDO2) SPECIFICATION Output Voltage Dropout (ASO_RAIL − VOUT2) IOUT2 = 0 mA to 300 mA, 7 V < ASO_RAIL < 18 V VDR2 3.234 3.3 IOUT2 = 300 mA (Note 7) Load Regulation IOUT2 = 0 mA to 300 mA, VIN_B = 13.2 V 0 66 mV/mA Line Regulation IOUT2 = 1 mA, 7 V < ASO_RAIL < 18 V 0 1.2 mV/V Output Current Limit Output Load Capacitance Range Output Load Capacitance ESR Range (Notes 8 and 9) 400 mA Co Output Capacitance for Stability 1.0 100 mF ESRCo Maximum Cap ESR for stability 0.01 10 W DVOUT2 (ASO Low to High Transient) TJ = 25 °C , IOUT2 = 300 mA, ISYS = 400 mA, CASO_RAIL = 1 mF, ESRCo = 0.01 W, Co = 22 mF, VIN−A falling 30 66 $mV DVOUT2 (ASO high to Low Transient) TJ = 25 °C , IOUT2 = 300 mA, ISYS = 400 mA, CASO_RAIL = 1 mF, ESRCo = 0.01 W, Co = 22 mF, VIN−A rising 30 66 $mV VIN_B = 13.2 V, 0.5 VPP, 100 Hz 60 Power Supply Ripple Rejection (Note 8) PSRR Startup Overshoot IOUT2 = 0 mA to 300 mA dB 3 % 3.366 V LOW DROP−OUT LINEAR REGULATOR 3 (LDO3) SPECIFICATION Output Voltage VOUT3 IOUT3 = 0 mA to 400 mA, 7 V v VIN_S3 v 18 V Dropout (VIN_S3 − VOUT3) VDR3 IOUT3 = 300 mA (Note 7) Output Current Limit 3.234 3.3 1.5 400 V mA Load Regulation IOUT3 = 0 mA to 300 mA, VIN_B = 13.2 V 0 66 mV/mA Line Regulation IOUT3 = 1 mA, 7 V v VIN_S3 v 18 V 0 1.2 mV /V http://onsemi.com 7 NCV8613B ELECTRICAL CHARACTERISTICS (7 V < ASO_RAIL < 18 V, VIN−H = VIN−B w ASO_RAIL, VPP = 5 V, VIN_S3 tied to ASO_RAIL, VBATT_MON = 0 V, IGNIN = 0 V, ISYS = 3 mA (Note 6)) Min/Max values are valid for the temperature range −40°C vTJ v 150 °C unless noted otherwise. Min/Max values are guaranteed by test, design or statistical correlation. Parameter Symbol Conditions Min Typ Max Unit LOW DROP−OUT LINEAR REGULATOR 3 (LDO3) SPECIFICATION Output Load Capacitance Range Output Load Capacitance ESR Range (Notes 8 and 9) Co ESRCo Output Capacitance for Stability 1.0 100 mF Maximum Capacitance ESR for stability 0.01 12 W DVOUT3 (ASO Low to High Transient) TJ = 25 °C , IOUT3 = 300 mA, ISYS = 400 mA, CASO_RAIL = 1 mF, ESRCo = 0.01 W, Co = 47 mF, VIN−A falling 30 66 $mV DVOUT3 (ASO high to Low Transient) TJ = 25 °C , IOUT3 = 300 mA, ISYS = 400 mA, CASO_RAIL = 1 mF, ESRCo = 0.01 W, Co = 47 mF, VIN−A rising 30 66 $mV VIN_B = 13.2 V, 0.5 VPP, 100 Hz 60 Power Supply Ripple Rejection (Note 8) Startup Overshoot PSRR IOUT3 = 0 mA to 300 mA dB 3 % 7. Dropout voltage is measured when the output voltage has dropped 100 mV relative to the nominal value obtained with ASO_RAIL = VIN_S3 = 13.2 V. 8. Not tested in production. Limits are guaranteed by design. 9. Refer to CIRCUIT DESCRIPTION Section for Stability Consideration ORDERING INFORMATION Device NCV8613BMNR2G Conditions No Enable, LDO2 Reset monitor Package Shipping 20 Lead DFN, 5x6 (Pb−Free) 2500 / Tape & Reel http://onsemi.com 8 3 VIN-H VIN-A VOUT3 VOUT2 20 8V 19 18 Output Filter 4 VIN-B VIN_S3 3.3Vs Output Filter 2 ASO_RAIL LDO3 VOUT3 1 LDO2 VOUT2 VBATT 8V AUTO SWITCHOVER Oring Diodes & Filter NCV8613B 3.3Vs VBATT_MON Ignition Filter HOT_FLG Ignition 8 10 11 12 Power Amplifier HOT_FLG IGNIN IGNOUT VOUT1 VPP RST DLY Output Filter BO_DET LDO1 VOUT1 7 HV_DET RESET / DELAY NC 6 MONITORING LOGIC HV_DET BO_DET VPP INGITOIN BUFFER 5 17 16 5Vs HOT_FLG_S HV_DET BO_DET RST 15 DLY 14 SMPS1 Power Stage 8V output, 4A ILIMIT DVD ROM Drive 6 8V 7 8 9 HOT_FLG OCSET BST2 BST1 VIN_SW 3 34 SN2 SN1 GL1 SW_FB2 SW_FB1 SYNC COMP1 SYS_EN HS_EN LDO_EN HOT_FLG 5V Misc. 5 V Logic LDO_EN 3.3V Misc. 3.3 V Logic HOT_FLG VBATT 25 23 GH1 COMP2 4 38 24 27 28 SMPS2 Power Stage 5V output, 2A ILIMIT 5 HS_EN SMPS2 VOUT2 VBATT 26 MAIN SMPS1 VOUT1 HS_EN LDO_EN SYS_EN Main C 3.3Vs NCV8855 33 Body CAN VPP NCV8613B NCV8613 SYS_EN SDARS 5V Headunit CAN USB Connector 37 VBATT 2 39 22 ISNS2+ ISNS1- ISNS2- LR_G1 30 31 LR_FB1 VIN 29 32 HIGH-SIDE SWITCH HS_S 21 LDO2 Power Stage 3.3V output, 1A ILIMIT 40 ISNS1+ LDO2 VOUT4 8.5V 1 LDO1 VOUT3 AM/FM Tuner LDO1 Power Stage 8.5V output, 0.4A ILIMIT VBATT 3.3V Main DSP Active Antenna Fan Figure 2. Automotive Radio System Block Diagram Example NCV8613B with NCV8855 http://onsemi.com 9 NCV8613B CIRCUIT DESCRIPTION Auto Switchover Circuitry The auto switchover circuit is designed to insure continuous operation of the device, automatically switching the input voltage from the ASO_RAIL input, to the VIN−B input, to the VIN−H input depending on conditions. The primary input voltage pin is ASO_RAIL, which is driven from the 8 V supply. When this voltage is present it will drive the output voltages. Regardless of whether the 8 V supply is available, the reference and core functions of the device will be driven by the higher of VIN−B and VIN−H. The switchover control circuitry will be powered solely by the 8 V supply, via VIN−A. When the 8 V supply is not present, the gates of the 2 P−FET switches will be pulled to ground, turning the switches on. In this condition, the VIN−B and VIN−H voltages will be diode or’ed, with the higher voltage powering the chip. The VIN−H voltage will be one diode lower than the VIN−B voltage, thereby forcing the VIN−B voltage to be dominant supply. In the event that both the 8 V supply and the VIN−B supply are not present, the VIN−H supply will be powering the device. The VIN−H supply is then fed from a recommended 1000 mF cap. The duration of VIN−H supply is dependent on output current. It is intended as protection against temporary loss of battery conditions. In the event of a double battery, or prolonged high voltage condition on the battery line, a bleed transistor has been included on the VIN−H line. With the large hold−up cap on VIN−H, the voltage on that pin has the potential to remain in an elevated position for an extended period of time. The main result of this condition would be an Overvoltage Shutdown of the device. In order to avoid this condition, a transistor that is connected to the Overvoltage Shutdown signal is tied to the VIN−H line. This transistor will become active in a high voltage event, allowing the hold−up cap to discharge the excess voltage in a timely manner. In the Block Diagram, Figure 1, CASO_RAIL is listed as a 1 mF capacitor. It is required for proper operation of the device that CASO_RAIL is no larger than 1 mF. During a switchover event, a timer in the output stages prepares the regulator in anticipation of change in input voltage. The event results in a hitch in the output waveforms, as can be seen in Figure 3. IOUT = 100 mA COUT = 47 mF Figure 3. VOUTX Response to ASO Switchover Event VIN−B/VIN−H Minimum Operating Voltage The internal reference and core functions are powered by either the VIN−B or VIN−H supply. The higher of the two voltages will dominate and power the reference. This provides quick circuit response on start−up, as well as a stable reference voltage. Since the VIN−B voltage will come up much more quickly than the VIN−H voltage, initially, the VIN−B voltage will be running the reference. In the case of any transient drops on VIN−B, the VIN−H supply, with its large hold−up capacitor, will then be the dominant voltage, and will be powering the reference. For proper operation of the device, VIN−B or VIN−H must be at least 4.5 V. Below that voltage the reference will not operate properly, leading to incorrect functioning by the device. VIN−B or VIN−H must be greater than 4.5 V regardless of the voltage on the VIN−A pin. Internal Soft−Start The NCV8613B is equipped with an internal soft−start function. This function is included to limit inrush currents and overshoot of output voltages. The soft−start function applies to all 3 regulators. The soft−start function kicks in for start up, start up via enable, start up after thermal shutdown, and startup after an over voltage condition. LDO3 is not subject to soft−start under all conditions. The LDO3 output is not affected by overvoltage shutdown, and http://onsemi.com 10 NCV8613B The maximum dissipation the NCV8613B can handle is given by: PD(max) = (TJ(max)−TA)/RthJA See Figure 18 for RthJA versus PCB Area. RthJA could be further decreased by using Multilayer PCB and/or if Air Flow is taken into account. therefore is not effected by the soft−start function upon the device’s return from an over voltage condition. Also, when VIN_S3 is connected to an independent supply and the supply is made available after the soft−start function, LDO3 will not have an independent soft−start. LDO1 Regulator The LDO1 error amplifier compares the reference voltage to a sample of the output voltage (VOUT1) and drives the gate of an internal PFET. The reference is a bandgap design to give it a temperature−stable output. IGNOUT Circuitry The IGNOUT pin is an open drain output Schmitt Trigger, externally pulled up to 3.3 V via a 10 kW resistor. The IGNOUT pin can be used to monitor the ignition signal of the vehicle, and send a signal to mute an audio amplifier during engine crank. The IGNIN pin is ESD protected, and can handle peak transients up to 45 V. An external diode is recommended to protect against negative voltage spikes. The IGNOUT circuitry requires the device to be enabled for proper operation. LDO2 Regulator The LDO2 error amplifier compares the reference voltage to a sample of the output voltage (VOUT2) and drives the gate of an internal PFET. The reference is a bandgap design to give it a temperature−stable output. LDO3 Regulator VPP Function The LDO3 error amplifier compares the reference voltage to a sample of the output voltage (VOUT3) and drives the gate of an internal PFET. The reference is a bandgap design to give it a temperature−stable output The reset and warning circuits utilize a push−pull output stage. The high signal is provided by VPP. VPP is an externally fed signal that can be tied to an output, or tied to another regulated voltage signal, typically 5 V, but as low as 3.0 V. Under this setup, and any setup where LDO’s 1−3 are tied to VPP, loss of the VPP signal can occur if the pull up voltage is reduced due to over current, thermal shutdown, or overvoltage conditions. Stability Considerations The output or compensation capacitors, COUTX help determine three main characteristics of a linear regulator: startup delay, load transient response and loop stability. The capacitor values and type should be based on cost, availability, size and temperature constraints. Tantalum, aluminum electrolytic, film, or ceramic capacitors are all acceptable solutions, however, attention must be paid to ESR constraints. The aluminum electrolytic capacitor is the least expensive solution, but, if the circuit operates at low temperatures (−25°C to −40°C), both the value and ESR of the capacitor will vary considerably. The capacitor manufacturer’s data sheet usually provides this information. The value for each output capacitor COUTX shown in Figures 20 − 25 should work for most applications; however, it is not necessarily the optimized solution. Stability is guaranteed at the following values: Reset Outputs The Reset Output is used as the power on indicator to the Microcontroller. The NCV8613B Reset circuitry monitors the output on LDO2. This signal indicates when the output voltage is suitable for reliable operation. It pulls low when the output is not considered to be suitable. The Reset circuitry utilizes a push pull output stage, with VPP as the high signal. In the event of the part shutting down via Battery voltage or Enable, the Reset output will be pulled to ground. The input and output conditions that control the Reset Output and the relative timing are illustrated in Figure 4, Reset Timing. Output voltage regulation must be maintained for the delay time before the reset output signals a valid condition. The delay for the reset output is defined as the amount of time it takes the timing capacitor on the delay pin to charge from a residual voltage of 0 V to the Delay timing threshold voltage VD of 2 V. The charging current for this is ID of 5 mA. By using typical IC parameters with a 10 nF capacitor on the Delay Pin, the following time delay is derived: tRD = CD * VDU / ID tRD = 10 nF * (2 V)/ (5 mA) = 4 ms Other time delays can be obtained by changing the CD capacitor value. The Delay Time can be reduced by decreasing the capacitance of CD. Using the formula above, delay can be reduced as desired. Leaving the Delay Pin open COUT1 w 47 mF, ESR v 10 W COUT2 w 47 mF, ESR v 10 W COUT3 w 47 mF, ESR v 10 W Actual limits are shown in graphs in the Typical Performance Characteristics section. Thermal As power in the NCV8613B increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. When the NCV8613B has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power applications. http://onsemi.com 11 NCV8613B typically 160°C to 180°C. The Hot Flag signal will remain low until the junction temperature drops below the Hot Flag threshold. The Hot_Flag circuitry does not run off the VBATT_MON Pin, and can not be disabled by grounding VBATT_MON. Each of the three warning circuits utilizes a push−pull output stage. The high signal is provided by VPP. When VPP is tied to an output of the NCV8613B, the signal will go low if the corresponding output shuts down due to a fault condition. is not desirable as it can result in unwanted signals being coupled onto the pin. VBATT_MON and Warning Flags The NCV8613B is equipped with High Voltage Detection, Brown Out Detection, and High Temperature Detection circuitry. The Overvoltage Shutdown, High Voltage, and Brown Out Detection circuitry are all run off the VBATT_MON input. If this functionality is not desired, grounding of the VBATT_MON pin will turn off the functions. The HV_DET and BO_DET signals are in a high impedance state until the VBATT_MON circuitry reaches it minimum operating voltage, typically 1.0 V to 2.5 V. At that point the BO_DET signal will be held low, while the HV_DET signal will go high. The BO_DET signal will go high once the VBATT_MON signal reaches the Brown Out Threshold, typically 7 V to 8 V. The BO_DET signal will stay high until the VBATT_MON voltage drops below the Brown Out Threshold. The HV_DET signal will stay high until the VBATT_MON voltage rises above the HV_DET threshold, typically 16.2 V to 17.8 V. The HV_DET signal will reassert high once the HV_DET signal crosses the HV_DET threshold going low. The NCV8613B is also equipped with a Hot Flag pin which indicates when the junction temperature is approaching thermal shutdown. The Hot Flag signal will remain high as long as the junction temperature is below the Hot flag threshold, typically 140°C to 160°C. This pin is intended as a warning that the junction temperature is approaching the Thermal Shutdown threshold, which is Overvoltage Shutdown The NCV8613B is equipped with overvoltage shutdown (OVS) functionality. The OVS is designed to turn on when the VBATT_MON signal crosses 17 V. If the VBATT_MON pin is tied to ground, the OVS functionality will be disabled. When OVS is triggered, LDO1 and LDO2 will both be shut down. LDO3 is run off a separate input voltage line, VIN_S3, and will not shutdown in this condition. Once the OVS condition has passed, LDO1 and LDO2 will both turn back on. The VIN−H line is equipped with a bleed transistor to prevent a continued OVS condition on the chip once the high battery condition has subsided. This transistor is needed to discharge the high voltage from the VIN−H hold−up capacitor. This transistor will only turn on when an OVS is detected on−chip, and will turn off as soon as the OVS condition is no longer detected by the chip. Load Dump 17 V Vin Vout Reset Threshold LDOX Delay Reset Power On Reset Overload on Output Over Voltage On Input Overvoltage on Input Momentary Glitch on Output Figure 4. NCV8613B Reset Timing Diagram http://onsemi.com 12 Shutdown via Input NCV8613B Load Dump VIN_B 7.0 V 4.4 V 45 V > 3.25 V IGNIN <1V −100 V 5.0 V IGNOUT Figure 5. IGNOUT Timing Diagram http://onsemi.com 13 NCV8613B 8V VIN_A Overvoltage on VIN−B 17V 13.2V VIN_B Voltage Clamped at 16 V 16V 13.2V VIN_H DVIN−H xxV TVIN−H 17V 13.2V Duration of TVIN−H and drop of DVIN−H dependant on output load conditions 7V ASO_RAIL LDOX Delay Reset VIN−B Turns 8V Switching Output Loss of VIN−B Back On Voltage from SMPS ASIC Undervoltage Turns On. 8V Switching Output Lockout Voltage from SMPS ASIC Turns Off. Overvoltage Shutdown 8V Switching Output Voltage from SMPS ASIC Turns On. Shutdown Figure 6. Auto Switchover Circuit Timing Diagram VBATTMON Connected to ASO_RAIL http://onsemi.com 14 NCV8613B 17V 16.5V VBATT_MON 8V 7.85V 7.5V 2.5V 2.0V 1.5V 1.0V VPP HV_DET VPP BO_DET Overvoltage on Input Voltage Dip on Input Figure 7. Warning Circuitry Timing Diagram 170°C 160°C 150°C 140°C TJ LDOX VPP HOT_FLG Hot Flag Recovers Hot Flag Triggers Thermal Shutdown Thermal Recovery Figure 8. Thermal Shutdown Timing Diagram http://onsemi.com 15 NCV8613B 17V 13.2V 7V ASO_RAIL VBATT_MON 5.0V LDO1 3.3V LDO2 LDO2 Reset Threshold 3.3V LDO3 Delay Reset Overvoltage Shutdown Glitch on LDO2 Figure 9. NCV8613B Regulator Output Timing Diagram– VIN_S3 Tied to ASO_RAIL http://onsemi.com 16 NCV8613B Load Dump 17V 13.2V ASO_OUT LDO1 LDO2 LDO3 Figure 10. NCV8613B Regulator Output Timing Diagram− VBATT_MON Grounded http://onsemi.com 17 NCV8613B 3.40 IOUT1 = 100 mA 5.08 VOUT2, OUTPUT VOLTAGE (V) VOUT1, OUTPUT VOLTAGE (V) 5.10 5.06 5.04 5.02 5.0 4.98 4.96 4.94 4.92 4.9 −40 −20 0 20 40 60 80 100 120 3.32 3.30 3.28 3.26 3.24 3.22 −20 0 20 40 60 80 100 120 TEMPERATURE (°C) Figure 11. Output Voltage LDO1 vs Temperature Figure 12. Output Voltage LDO2 vs Temperature 140 250 IOUT3 = 100 mA VDR1, DROPOUT VOLTAGE (mV) VOUT3, OUTPUT VOLTAGE (V) 3.34 TEMPERATURE (°C) 3.38 3.36 3.34 3.32 3.30 3.28 3.26 3.24 3.22 3.20 −40 −20 0 20 40 60 80 100 120 TJ = 25°C VOUT1 = 5.0 V 200 150 100 50 0 140 0 20 40 60 80 TEMPERATURE (°C) IOUT1, OUTPUT CURRENT (mA) Figure 13. Output Voltage LDO3 vs Temperature Figure 14. Dropout LDO1 vs Output Current 100 1000 1200 TJ = 25°C VOUT2 = 3.3 V 1000 VDR3, DROPOUT VOLTAGE (mV) VDR2, DROPOUT VOLTAGE (mV) 3.36 3.20 −40 140 3.40 800 600 400 200 0 IOUT2 = 100 mA 3.38 0 50 100 150 200 250 300 900 TJ = 25°C VOUT3 = 3.3 V 800 700 600 500 400 300 200 100 0 0 50 100 150 200 250 IOUT2, OUTPUT CURRENT (mA) IOUT3, OUTPUT CURRENT (mA) Figure 15. Dropout LDO2 vs Output Current Figure 16. Dropout LDO3 vs Output Current http://onsemi.com 18 300 NCV8613B 170 RqJA, THERMAL RESISTANCE JUNCTION−TO−AMBIENT (°C/W) HV_DET THRESHOLD (V) 19.5 19 18.5 18 17.5 17 16.5 1 10 100 1000 10000 100000 1000000 150 130 110 1−oz Cu single layer PCB 90 70 2−oz Cu single layer PCB 50 30 0 100 200 300 400 500 600 700 PCB COPPER AREA (mm2) ASO−RAIL VOLTAGE RAMP (V/s) Figure 17. HV−DET Threshold vs. dV/dt Figure 18. RqJA vs. Copper Area 1000 RqJA, (°C/W) 100 10 1 D = 0.5 0.2 0.1 0.05 0.01 2−oz Cu single layer PCB, 100 mm2 0.1 Single Pulse 0.01 0.001 1E−06 TSP 1E−05 0.0001 0.001 0.01 0.1 PULSE TIME (sec) Figure 19. RqJA vs. Duty Cycle http://onsemi.com 19 1 10 100 1000 NCV8613B 100 100 Stable Region 10 1 0.1 Unstable Region 10 ESR (W) ESR (W) VIN = 18 V VOUT1 = 5 V COUT1 = 1 mF Unstable Region 0.01 1 0.1 0.01 Unexplored Region* Unexplored Region* 0.001 VIN = 18 V VOUT1 = 5 V COUT1 = 47 mF Stable Region 0 20 40 60 80 0.001 100 0 20 IOUT1, OUTPUT CURRENT (mA) 40 60 80 100 IOUT1, OUTPUT CURRENT (mA) Figure 20. COUT1 ESR Stability Region − 1 mF Figure 21. COUT1 ESR Stability Region − 47 mF *The min specified ESR is based on Murata’s capacitor GRM31CR60J476ME19 used in measurement. The true min ESR limit might be lower than shown. 100 100 Stable Region 10 1 0.1 ESR (W) ESR (W) 10 Unstable Region VIN = 18 V VOUT2 = 3.3 V COUT2 = 1 mF Unstable Region 1 VIN = 18 V VOUT2 = 3.3 V COUT2 = 47 mF Stable Region 0.1 0.01 0.01 Unexplored Region* 0.001 0 50 100 150 200 0.001 300 250 0 50 IOUT2, OUTPUT CURRENT (mA) 100 150 200 250 300 IOUT2, OUTPUT CURRENT (mA) Figure 22. COUT2 ESR Stability Region − 1 mF Figure 23. COUT2 ESR Stability Region − 47 mF *The min specified ESR is based on Murata’s capacitor GRM31CR60J476ME19 used in measurement. The true min ESR limit might be lower than shown. 100 100 Stable Region 10 1 0.1 ESR (W) ESR (W) 10 Unstable Region VIN = 18 V VOUT3 = 3.3 V COUT3 = 1 mF Unstable Region 1 VIN = 18 V VOUT3 = 3.3 V COUT3 = 47 mF Stable Region 0.1 0.01 0.01 0.001 0.001 Unexplored Region* 0 50 100 150 200 300 250 0 50 IOUT3, OUTPUT CURRENT (mA) 100 150 200 250 300 IOUT3, OUTPUT CURRENT (mA) Figure 24. COUT3 ESR Stability Region − 1 mF Figure 25. COUT3 ESR Stability Region − 47 mF http://onsemi.com 20 NCV8613B dt = 21.4 ms IOUT3 = 300 mA Figure 26. Output Response of LDO3 to Loss of Vin−B dt = 121 ms IOUT2 = 80 mA Figure 27. Output Response of LDO2 to Loss of Vin−B http://onsemi.com 21 NCV8613B Figure 28. HV−DET Response to High Voltage − VBAT−MON tied to ASO−RAIL Figure 29. HV−DET Response to High Voltage − VBAT−MON Left Open http://onsemi.com 22 NCV8613B Figure 30. BO−DET Response to LOW Voltage − VBAT−MON tied to ASO−RAIL Figure 31. BO−DET Response to LOW Voltage − VBAT−MON Left Open http://onsemi.com 23 NCV8613B Figure 32. Output Response to OVS − VBAT−MON tied to ASO−RAIL Figure 33. Output Response to OVS − VBAT−MON Left Open http://onsemi.com 24 NCV8613B PACKAGE DIMENSIONS DFN20 CASE 505AB−01 ISSUE B A D NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINALS AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. B PIN 1 LOCATION E 2X 0.15 C 2X DIM A A1 A2 A3 b D D2 E E2 e K L TOP VIEW 0.15 C 0.10 C A2 A 0.08 C A1 SIDE VIEW (A3) C SEATING PLANE D2 20X 20X L MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.65 0.75 0.20 REF 0.20 0.30 6.00 BSC 3.98 4.28 5.00 BSC 2.98 3.28 0.50 BSC 0.20 −−− 0.50 0.60 SOLDERING FOOTPRINT* e 20X 1 10 0.78 4.24 E2 K 20 20X b 0.10 C A B 0.05 C 3.24 PACKAGE OUTLINE 11 5.30 1 NOTE 3 BOTTOM VIEW 0.50 PITCH 20X 0.35 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 25 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV8613B/D