MX25L1605D, 3V, 16Mb, v1.5.pdf

MX25L1605D
MX25L3205D
MX25L6405D
16M-BIT [x 1 / x 2] CMOS SERIAL FLASH
32M-BIT [x 1 / x 2] CMOS SERIAL FLASH
64M-BIT [x 1 / x 2] CMOS SERIAL FLASH
FEATURES
GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 16M:16,777,216 x 1 bit structure or 8,388,608 x 2 bits (two I/O read mode) structure
32M:33,554,432 x 1 bit structure or 16,772,216 x 2 bits (two I/O read mode) structure
64M:67,108,864 x 1 bit structure or 33,554,432 x 2 bits (two I/O read mode) structure
• 512 Equal Sectors with 4K byte each (16Mb)
1024 Equal Sectors with 4K byte each (32Mb)
2048 Equal Sectors with 4K byte each (64Mb)
- Any Sector can be erased individually
• 32 Equal Blocks with 64K byte each (16Mb)
64 Equal Blocks with 64K byte each (32Mb)
128 Equal Blocks with 64K byte each (64Mb)
- Any Block can be erased individually
• Single Power Supply Operation
- 2.7 to 3.6 volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V
PERFORMANCE
• High Performance
- Fast access time: 86MHz serial clock (15pF + 1TTL Load) and 66MHz serial clock (30pF + 1TTL Load)
- Serial clock of two I/O read mode : 50MHz (15pF + TTL Load), which is equivalent to 100MHz
- Fast program time: 1.4ms(typ.) and 5ms(max.)/page (256-byte per page)
- Byte program time: 9us (typical)
- Continuously program mode (automatically increase address under word program mode)
- Fast erase time: 60ms(typ.) /sector (4K-byte per sector) ; 0.7s(typ.) /block (64K-byte per block); 14s(typ.) /chip
for 16Mb, 25s(typ.) for 32Mb, and 50s(typ.) for 64Mb
• Low Power Consumption
- Low active read current: 25mA(max.) at 86MHz, 20mA(max.) at 66MHz and 10mA(max.) at 33MHz
- Low active programming current: 20mA (max.)
- Low active erase current: 20mA (max.)
- Low standby current: 20uA (max.)
- Deep power-down mode 1uA (typical)
• Typical 100,000 erase/program cycles
• 20 years of data retention
SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- Block lock protection
The BP0-BP3 status bit defines the size of the area to be software protection against program and erase instructions
- Additional 512-bit secured OTP for unique identifier
• Auto Erase and Auto Program Algorithm
- Automatically erases and verifies data at selected sector
- Automatically programs and verifies data at selected page by an internal algorithm that automatically times the
program pulse widths (Any page to be programed should have page in the erased state first)
P/N: PM1290
1
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
• Status Register Feature
• Electronic Identification
- JEDEC 1-byte manufacturer ID and 2-byte device ID
- RES command for 1-byte Device ID
- Both REMS and REMS2 commands for 1-byte manufacturer ID and 1-byte device ID
HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI Input
- Serial Data Input
• SO Output
- Serial Data Output
• WP#/ACC pin
- Hardware write protection and program/erase acceleration
• HOLD# pin
- pause the chip without diselecting the chip
• PACKAGE
- 16-pin SOP (300mil)
- 8-land WSON (8x6mm or 6x5mm)
- 8-pin SOP (200mil, 150mil)
- 8-pin PDIP (300mil)
- 8-land USON (4x4mm)
- All Pb-free devices are RoHS Compliant
ALTERNATIVE
• Security Serial Flash (MX25L1615D/MX25L3215D/MX25L6415D) may provides additional protection features for
option. The datasheet is provided under NDA.
GENERAL DESCRIPTION
The MX25L1605D are 16,777,216 bit serial Flash memory, which is configured as 2,097,152 x 8 internally. When
it is in two I/O read mode, the structure becomes 8,388,608 bits x 2. The MX25L3205D are 33,554,432 bit serial
Flash memory, which is configured as 4,194,304 x 8 internally. When it is in two I/O read mode, the structure becomes 16,772,216 bits x 2. The MX25L6405D are 67,108,864 bit serial Flash memory, which is configured as 8,388,608
x 8 internally. When it is in two I/O read mode, the structure becomes 33,554,432 bits x 2. (please refer to the "Two
I/O Read mode" section). The MX25L1605D/3205D/6405D feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input (SCLK), a serial data input (SI),
and a serial data output (SO). Serial access to the device is enabled by CS# input.
When it is in two I/O read mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and data output.
The MX25L1605D/3205D/6405D provides sequential read operation on whole chip.
After program/erase command is issued, auto program/ erase algorithms which program/ erase and verify the
specified page or sector/block locations will be executed. Program command is executed on byte basis, or page (256
bytes) basis, or word basis for Continuously program mode, and erase command is executes on sector (4K-byte),
or block (64K-byte), or whole chip basis.
P/N: PM1290
2
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read
command can be issued to detect completion status of a program or erase operation via WIP bit.
Advanced security features enhance the protection and security functions, please see security features section for
more details.
When the device is not in operation and CS# is high, it is put in standby mode and draws less than 20uA DC current.
The MX25L1605D/3205D/6405D utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after typical 100,000 program and erase cycles.
Table 1. Additional Feature Comparison
Additional
Features
Part
Name
Protection and Security
Read
Performance
Flexible Block
512-bit secured
Protection
OTP
(BP0-BP3)
2 I/O Read
(50MHz)
MX25L1605D
V
V
MX25L3205D
V
V
MX25L6405D
V
V
P/N: PM1290
Identifier
Device ID
Device ID
Device ID
(command: AB (command: 90 (command: EF
hex)
hex)
hex)
C2 14 (hex)
C2 14 (hex)
14 (hex)
(if ADD=0)
(if ADD=0)
C2 15 (hex)
C2 15 (hex)
15 (hex)
(if ADD=0)
(if ADD=0)
C2 16 (hex)
C2 16 (hex)
16 (hex)
(if ADD=0)
(if ADD=0)
V
V
V
3
RDID
(command: 9F
hex)
C2 20 15 (hex)
C2 20 16 (hex)
C2 20 17 (hex)
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
PIN CONFIGURATIONS
16-PIN SOP (300mil)
HOLD#
VCC
NC
NC
NC
NC
CS#
SO/SIO1
8-PIN SOP (200mil, 150mil)
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
SCLK
SI/SIO0
NC
NC
NC
NC
GND
WP#/ACC
CS#
SO/SIO1
WP#/ACC
GND
1
2
3
4
8
7
6
5
VCC
HOLD#
SCLK
SI/SIO0
CS#
SO/SIO1
WP#/ACC
GND
P/N: PM1290
VCC
HOLD#
SCLK
SI/SIO0
1
2
3
4
8
7
6
5
VCC
HOLD#
SCLK
SI/SIO0
PIN DESCRIPTION
PACKAGE OPTIONS
150mil 8-SOP
200mil 8-SOP
300mil 16-SOP
300mil 8-PDIP
6x5mm WSON
8x6mm WSON
4x4mm USON
8
7
6
5
8-PIN PDIP (300mil)
8-LAND WSON (8x6mm, 6x5mm), USON (4x4mm)
CS#
SO/SIO1
WP#/ACC
GND
1
2
3
4
16M
V
V
V
V
V
32M
V
V
V
V
V
V
64M
SYMBOL DESCRIPTION
CS#
SI/SIO0
Chip Select
Serial Data Input (for 1 x I/O)/ Serial Data
Input & Output (for 2xI/O read mode)
SO/SIO1 Serial Data Output (for 1 x I/O)/ Serial Data
Input & Output (for 2xI/O read mode)
SCLK
Clock Input
WP#/ACC Write protection: connect to GND ; 9.5~10.5V
for program/erase acceleration: connect to
9.5~10.5V
HOLD# H o l d , t o p a u s e t h e d e v i c e w i t h o u t
deselecting the device
VCC
+ 3.3V Power Supply
GND
Ground
V
V
4
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
BLOCK DIAGRAM
X-Decoder
Address
Generator
Memory Array
Page Buffer
SI/SIO0
Data
Register
Y-Decoder
SO/SIO1
CS#,
WP#/ACC,
HOLD#
SCLK
SRAM
Buffer
Mode
Logic
State
Machine
Sense
Amplifier
HV
Generator
Clock Generator
Output
Buffer
P/N: PM1290
5
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
DATA PROTECTION
The MX25L1605D/3205D/6405D is designed to offer protection against accidental erasure or programming caused
by spurious system level signals that may exist during power transition. During power up the device automatically
resets the state machine in the standby mode. In addition, with its control register architecture, alteration of the
memory contents only occurs after successful completion of specific command sequences. The device also incorporates several features to prevent inadvertent write cycles resulting from VCC power-up and power-down transition or system noise.
• Valid command length checking: The command length will be checked whether it is at byte base and completed
on byte boundary.
• Write Enable (WREN) command: WREN command is required to set the Write Enable Latch bit (WEL) before
other command to change data. The WEL bit will return to reset stage under following situation:
- Power-up
- Write Disable (WRDI) command completion
- Write Status Register (WRSR) command completion
- Page Program (PP) command completion
- Continuously Program mode (CP) instruction completion
- Sector Erase (SE) command completion
- Block Erase (BE) command completion
- Chip Erase (CE) command completion
• Deep Power Down Mode: By entering deep power down mode, the flash device also is under protected from
writing all commands except Release from deep power down mode command (RDP) and Read Electronic Signature command (RES).
• Advanced Security Features: there are some protection and securuity features which protect content from inadvertent write and hostile access.
I. Block lock protection
- The Software Protected Mode (SPM) use (BP3, BP2, BP1, BP0) bits to allow part of memory to be protected
as read only. The proected area definition is shown as table of "Protected Area Sizes", the protected areas are
more flexible which may protect various area by setting value of BP0-BP3 bits.
Please refer to table of "protected area sizes".
- The Hardware Proteced Mode (HPM) use WP#/ACC to protect the (BP3, BP2, BP1, BP0) bits and SRWD bit.
P/N: PM1290
6
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 2. Protected Area Sizes
Status bit
BP3 BP2 BP1 BP0
16Mb
0
0
0
0 0 (none)
0
0
0
1 1 (1block, block 31th)
0
0
1
0 2 (2blocks, block 30th-31th)
0
0
1
1 3 (4blocks, block 28th-31th)
0
1
0
0 4 (8blocks, block 24th-31th)
0
1
0
1 5 (16blocks, block 16th-31th)
0
1
1
0 6 (32blocks, all)
0
1
1
1 7 (32blocks, all)
1
0
0
0 8 (32blocks, all)
1
0
0
1 9 (32blocks, all)
1
0
1
0 10 (16blocks, block 0th-15th)
1
0
1
1 11 (24blocks, block 0th-23th)
1
1
0
0 12 (28blocks, block 0th-27th)
1
1
0
1 13 (30blocks, block 0th-29th)
1
1
1
0 14 (31blocks, block 0th-30th)
1
1
1
1 15 (32blocks, all)
Protect Level
32Mb
0 (none)
1 (1block, block 63th)
2 (2blocks, block 62th-63th)
3 (4blocks, block 60th-63th)
4 (8blocks, block 56th-63th)
5 (16blocks, block 48th-63th)
6 (32blocks, block 32th-63th)
7 (64blocks, all)
8 (64blocks, all)
9 (32blocks, block 0th-31th)
10 (48blocks, block 0th-47th)
11 (56blocks, block 0th-55th)
12 (60blocks, block 0th-59th)
13 (62blocks, block 0th-61th)
14 (63blocks, block 0th-62th)
15 (64blocks, all)
64Mb
0 (none)
1 (2block, block 126th-127th)
2 (4blocks, block 124th-127th)
3 (8blocks, block 120th-127th)
4(16blocks, block 112th-127th)
5 (32blocks, block 96th-127th)
6 (64blocks, block 64th-127th)
7 (128blocks, all)
8 (128blocks, all)
9 (64blocks, 0th-63th)
10 (96blocks, block 0th-95th)
11 (112blocks, block 0th-111th)
12(120blocks, block 0th-119th)
13(124blocks, block 0th-123th)
14(126blocks, block 0th-125th)
15 (128blocks, all)
II. Additional 512-bit secured OTP for unique identifier: to provide 512-bit one-time program area for setting
device unique serial number - Which may be set by factory or system customer. Please refer to table 3. 512-bit
secured OTP definition.
- Security register bit 0 indicates whether the chip is locked by factory or not.
- To program the 512-bit secured OTP by entering 512-bit secured OTP mode (with ENSO command), and going through normal program procedure, and then exiting 512-bit secured OTP mode by writing EXSO command.
- Customer may lock-down the customer lockable secured OTP by writing WRSCUR(write security register)
command to set customer lock-down bit1 as "1". Please refer to table of "security register definition" for security
register bit definition and table of "512-bit secured OTP definition" for address range definition.
- Note: Once lock-down whatever by factory or customer, it cannot be changed any more. While in 512-bit secured OTP mode, array access is not allowed.
Table 3. 512-bit Secured OTP Definition
Address range
Size
Standard Factory Lock
Customer Lock
xxxx00~xxxx0F
128-bit
ESN (electrical serial number)
Determined by customer
xxxx10~xxxx3F
384-bit
N/A
P/N: PM1290
7
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
HOLD FEATURES
HOLD# pin signal goes low to hold any serial communications with the device. The HOLD feature will not stop the
operation of write status register, programming, or erasing in progress.
The operation of HOLD requires Chip Select(CS#) keeping low and starts on falling edge of HOLD# pin signal
while Serial Clock (SCLK) signal is being low (if Serial Clock signal is not being low, HOLD operation will not start
until Serial Clock signal being low). The HOLD condition ends on the rising edge of HOLD# pin signal while Serial Clock(SCLK) signal is being low( if Serial Clock signal is not being low, HOLD operation will not end until Serial
Clock being low), see Figure 1.
Figure 1. Hold Condition Operation
CS#
SCLK
HOLD#
Hold
Condition
(standard)
Hold
Condition
(non-standard)
The Serial Data Output (SO) is high impedance, both Serial Data Input (SI) and Serial Clock (SCLK) are don't care
during the HOLD operation. If Chip Select (CS#) drives high during HOLD operation, it will reset the internal logic of
the device. To re-start communication with chip, the HOLD# must be at high and CS# must be at low.
PROGRAM/ERASE ACCELERATION
To activate the program/erase acceleration function requires ACC pin connecting to 9.5~10.5V voltage (see Figure
2), and then to be followed by the normal program/erase process. By utilizing the program/erase acceleration operation, the performances are improved as shown on table of "ERASE AND PROGRAM PERFORMACE".
After power-up ready, it should wait 10ms at least to apply VHH(9.5~10.5V) on the WP#/ACC pin.
Figure 2. ACCELERATED PROGRAM TIMING DIAGRAM
9.5~10.5V
ACC
VHH
VIL or VIH
VIL or VIH
tVHH
tVHH
Note: tVHH (VHH Rise and Fall Time) min. 250ns
P/N: PM1290
8
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 4. COMMAND DEFINITION Command
(byte)
1st byte
2nd byte
WREN (write WRDI (write
enable)
disable)
06 (hex)
04 (hex)
RDID
(read
identification)
9F (hex)
RDSR
WRSR
FAST READ
READ (read
(read status (write status
(fast read
data)
register)
register)
data)
05 (hex)
01 (hex)
03 (hex)
AD1
0B (hex)
AD1
3rd byte
AD2
AD2
4th byte
5th byte
AD3
2READ (2
x I/O read
command)
Note1
BB (hex)
ADD(2)
ADD(2) &
Dummy(2)
AD3
Dummy
to read out to write new n bytes read n bytes read n bytes read
the values
values to out until CS# out until CS# out by 2 x I/
of the status the status
goes high
goes high
O until CS#
register
register
goes high
sets the
resets the
(WEL) write (WEL) write
enable latch enable latch
bit
bit
outputs
JEDEC
ID: 1-byte
Action
Manufacturer ID &
2-byte Device
ID
Note 1: The count base is 4-bit for ADD(2) and Dummy(2) because of 2 x I/O. And the MSB is on SI/SIO0 which is different from
1 x I/O condition.
Command
(byte)
SE (sector
erase)
BE (block
erase)
CE (chip
erase)
PP (page
program)
1st byte
2nd byte
3rd byte
4th byte
5th byte
20 (hex)
AD1
AD2
AD3
D8 (hex)
AD1
AD2
AD3
60 or C7 (hex)
02 (hex)
AD1
AD2
AD3
to erase the
selected
sector
to erase the
selected
block
to erase
whole chip
to program
the selected
page
Action
CP
RDP
(continuously DP (Deep
(Release
RES (read
program
power down) from deep electronic ID)
mode)
power down)
AD (hex)
B9 (hex)
AB (hex)
AB (hex)
AD1
x
AD2
x
AD3
x
continously enters deep release from to read out
program
power down deep power 1-byte Device
whole chip,
mode
down mode
ID
the address
automatically
increases
Note 2: ADD=00H will output the manufacturer ID first and ADD=01H will output device ID first.
Command
(byte)
1st byte
2nd byte
3rd byte
4th byte
5th byte
Action
REMS (read
REMS2 (read ENSO (enter
electronic
ID for 2x I/O
secured
manufacturer
mode)
OTP)
& device ID)
90 (hex)
EF (hex)
B1 (hex)
x
x
x
x
ADD (Note 2) ADD (Note 2)
ESRY
DSRY
EXSO (exit
RDSCUR
WRSCUR
(enable SO (disable SO
secured
(read security (write security
to output RY/ to output RY/
OTP)
register)
register)
BY#)
BY#)
C1 (hex)
2B (hex)
2F (hex)
70 (hex)
80 (hex)
output the
output the
to enter
to exit the to read value to set the to enable SO to disable SO
Manufacturer Manufacturer the 512-bit
512-bit
of security lock-down bit to output RY/ to output RY/
ID & Device ID & Device secured OTP secured OTP
register
as "1" (once BY# during BY# during
ID
ID
mode
mode
lock-down,
CP mode
CP mode
cannot be
updated)
Note 3: It is not recommended to adopt any other code not in the command definition table, which will potentially enter the hidden mode.
P/N: PM1290
9
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 5-1. Memory Organization (16Mb)
Block
31
30
29
28
27
Sector
511
..
.
496
495
..
.
480
479
..
.
464
463
..
.
448
447
..
.
432
Address Range
1FF000h
1FFFFFh
..
..
.
.
1F0000h
1F0FFFh
1EF000h
1EFFFFh
..
..
.
.
1E0000h
1DF000h
..
.
1D0000h
1CF000h
..
.
1C0000h
1BF000h
..
.
1B0000h
25
415
..
.
19F000h
..
.
19FFFFh
..
.
24
190000h
18F000h
..
.
22
367
..
.
16F000h
..
.
16FFFFh
..
.
351
..
.
15F000h
..
.
15FFFFh
..
.
352
21
20
19
336
335
..
.
320
319
..
.
304
18
16
150000h
14F000h
..
.
140000h
13F000h
..
.
130000h
159
..
.
09F000h
..
.
09FFFFh
..
.
128
127
..
.
080000h
07F000h
..
.
080FFFh
07FFFFh
..
.
144
143
..
.
090000h
08F000h
..
.
070000h
0A0FFFh
090FFFh
08FFFFh
..
.
070FFFh
06FFFFh
..
.
5
95
..
.
05F000h
..
.
05FFFFh
..
.
64
63
..
.
040000h
03F000h
..
.
040FFFh
03FFFFh
..
.
80
79
..
.
48
2
1
0
050000h
04F000h
..
.
030000h
060FFFh
050FFFh
04FFFFh
..
.
030FFFh
02F000h
..
.
02FFFFh
..
.
31
..
.
01F000h
..
.
01FFFFh
..
.
4
3
2
1
0
004000h
003000h
002000h
001000h
000000h
004FFFh
003FFFh
002FFFh
001FFFh
000FFFh
16
15
..
.
120FFFh
060000h
47
..
.
32
10
0A0000h
0B0FFFh
06F000h
..
.
3
100FFFh
0B0000h
0D0FFFh
0CFFFFh
..
.
111
..
.
4
110FFFh
10FFFFh
..
.
0D0000h
0CF000h
..
.
6
130FFFh
11FFFFh
..
.
100000h
0AFFFFh
..
.
96
140FFFh
13FFFFh
..
.
11F000h
..
.
110000h
10F000h
..
.
0AF000h
..
.
112
150FFFh
14FFFFh
..
.
287
..
.
272
271
..
.
10
175
..
.
7
160FFFh
12FFFFh
..
.
120000h
0C0FFFh
0BFFFFh
..
.
8
170FFFh
12F000h
..
.
256
P/N: PM1290
160000h
0C0000h
0BF000h
..
.
9
180FFFh
17FFFFh
..
.
303
..
.
288
17
170000h
11
192
191
..
.
208
207
..
.
160
190FFFh
18FFFFh
..
.
23
368
180000h
17F000h
..
.
0E0FFFh
0DFFFFh
..
.
176
1A0FFFh
384
383
..
.
240
239
..
.
Address Range
0FF000h
0FFFFFh
..
..
.
.
0F0000h
0F0FFFh
0EF000h
0EFFFFh
..
..
.
.
0E0000h
0DF000h
..
.
12
1B0FFFh
26
Sector
255
..
.
224
223
..
.
13
1C0FFFh
1BFFFFh
..
.
1AFFFFh
..
.
400
399
..
.
14
1D0FFFh
1CFFFFh
..
.
1AF000h
..
.
1A0000h
15
1E0FFFh
1DFFFFh
..
.
431
..
.
416
Block
020000h
010000h
00F000h
..
.
020FFFh
010FFFh
00FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 5-2. Memory Organization (32Mb)
Block
63
62
61
60
59
Sector
1023
..
.
1008
1007
..
.
992
991
..
.
976
975
..
.
960
959
..
.
944
Block
Address Range
3FF000h
3FFFFFh
..
..
.
.
3F0000h
3F0FFFh
3EF000h
3EFFFFh
..
..
.
.
3E0000h
3DF000h
..
.
3D0000h
3CF000h
..
.
3C0000h
3BF000h
..
.
3B0000h
47
46
3E0FFFh
3DFFFFh
..
.
45
3D0FFFh
3CFFFFh
..
.
44
3C0FFFh
3BFFFFh
..
.
43
943
..
.
3AF000h
..
.
3AFFFFh
..
.
42
39F000h
..
.
39FFFFh
..
.
41
57
927
..
.
56
55
912
911
..
.
896
895
..
.
880
54
879
..
.
864
53
52
51
863
..
.
848
847
..
.
832
831
..
.
816
50
815
..
.
800
49
48
799
..
.
784
783
..
.
768
P/N: PM1290
3A0000h
390000h
38F000h
..
.
380000h
37F000h
..
.
370000h
36F000h
..
.
360000h
35F000h
..
.
350000h
34F000h
..
.
340000h
33F000h
..
.
330000h
32F000h
..
.
320000h
31F000h
..
.
310000h
30F000h
..
.
300000h
752
751
..
.
2E0000h
2DF000h
..
.
2E0FFFh
2DFFFFh
..
.
704
703
..
.
2C0000h
2BF000h
..
.
2C0FFFh
2BFFFFh
..
.
720
719
..
.
390FFFh
38FFFFh
..
.
40
380FFFh
37FFFFh
..
.
39
36FFFFh
..
.
38
35FFFFh
..
.
37
350FFFh
34FFFFh
..
.
36
340FFFh
33FFFFh
..
.
35
671
..
.
29F000h
..
.
29FFFFh
..
.
640
639
..
.
280000h
27F000h
..
.
280FFFh
27FFFFh
..
.
656
655
..
.
32FFFFh
..
.
34
31FFFFh
..
.
33
310FFFh
30FFFFh
..
.
32
300FFFh
11
290000h
28F000h
..
.
270000h
2A0FFFh
290FFFh
28FFFFh
..
.
270FFFh
26F000h
..
.
26FFFFh
..
.
607
..
.
25F000h
..
.
25FFFFh
..
.
576
575
..
.
240000h
23F000h
..
.
240FFFh
23FFFFh
..
.
592
591
..
.
260000h
250000h
24F000h
..
.
230000h
260FFFh
250FFFh
24FFFFh
..
.
230FFFh
559
..
.
22F000h
..
.
22FFFFh
..
.
543
..
.
21F000h
..
.
21FFFFh
..
.
512
200000h
200FFFh
544
320FFFh
2A0000h
623
..
.
560
330FFFh
2B0FFFh
2AFFFFh
..
.
608
360FFFh
2B0000h
2D0FFFh
2CFFFFh
..
.
2AF000h
..
.
624
370FFFh
2D0000h
2CF000h
..
.
687
..
.
672
3A0FFFh
Address Range
2FF000h
2FFFFFh
..
..
.
.
2F0000h
2F0FFFh
2EF000h
2EFFFFh
..
..
.
.
736
735
..
.
688
3B0FFFh
58
928
Sector
767
..
.
528
527
..
.
220000h
210000h
20F000h
..
.
220FFFh
210FFFh
20FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Block
31
30
29
28
27
Sector
511
..
.
496
495
..
.
480
479
..
.
464
463
..
.
448
447
..
.
432
26
431
..
.
416
25
24
23
415
..
.
400
399
..
.
384
383
..
.
368
Address Range
1FF000h
1FFFFFh
..
..
.
.
1F0000h
1F0FFFh
1EF000h
1EFFFFh
..
..
.
.
1E0000h
1DF000h
..
.
1D0000h
1CF000h
..
.
1C0000h
1BF000h
..
.
1B0000h
1AF000h
..
.
1A0000h
19F000h
..
.
190000h
18F000h
..
.
180000h
17F000h
..
.
170000h
0E0FFFh
0DFFFFh
..
.
11
192
191
..
.
0C0000h
0BF000h
..
.
0C0FFFh
0BFFFFh
..
.
1AFFFFh
..
.
10
175
..
.
0AF000h
..
.
0AFFFFh
..
.
19FFFFh
..
.
9
159
..
.
09F000h
..
.
09FFFFh
..
.
128
127
..
.
080000h
07F000h
..
.
080FFFh
07FFFFh
..
.
190FFFh
18FFFFh
..
.
19
304
18
287
..
.
11F000h
..
.
11FFFFh
..
.
16
272
271
..
.
256
P/N: PM1290
110000h
10F000h
..
.
100000h
5
05FFFFh
..
.
64
63
..
.
040000h
03F000h
..
.
040FFFh
03FFFFh
..
.
1
80
79
..
.
0
060000h
050000h
04F000h
..
.
030000h
060FFFh
050FFFh
04FFFFh
..
.
030FFFh
47
..
.
02F000h
..
.
02FFFFh
..
.
31
..
.
01F000h
..
.
01FFFFh
..
.
4
3
2
1
0
004000h
003000h
002000h
001000h
000000h
004FFFh
003FFFh
002FFFh
001FFFh
000FFFh
16
15
..
.
12
070FFFh
05F000h
..
.
32
100FFFh
070000h
090FFFh
08FFFFh
..
.
95
..
.
2
110FFFh
10FFFFh
..
.
090000h
08F000h
..
.
0A0FFFh
06FFFFh
..
.
48
120FFFh
0A0000h
0B0FFFh
06F000h
..
.
3
130FFFh
0B0000h
0D0FFFh
0CFFFFh
..
.
111
..
.
4
140FFFh
13FFFFh
..
.
0D0000h
0CF000h
..
.
6
96
150FFFh
14FFFFh
..
.
12FFFFh
..
.
144
143
..
.
112
160FFFh
12F000h
..
.
120000h
7
170FFFh
303
..
.
288
17
130000h
8
180FFFh
17FFFFh
..
.
21
140000h
13F000h
..
.
160
1A0FFFh
15FFFFh
..
.
208
207
..
.
176
1B0FFFh
15F000h
..
.
320
319
..
.
12
1C0FFFh
1BFFFFh
..
.
351
..
.
20
13
1D0FFFh
1CFFFFh
..
.
16FFFFh
..
.
150000h
14F000h
..
.
240
239
..
.
Address Range
0FF000h
0FFFFFh
..
..
.
.
0F0000h
0F0FFFh
0EF000h
0EFFFFh
..
..
.
.
0E0000h
0DF000h
..
.
16F000h
..
.
336
335
..
.
14
Sector
255
..
.
224
223
..
.
367
..
.
160000h
15
1E0FFFh
1DFFFFh
..
.
22
352
Block
020000h
010000h
00F000h
..
.
020FFFh
010FFFh
00FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 5-3. Memory Organization (64Mb)
Block
127
126
125
124
123
Sector
2047
..
.
2032
2031
..
.
2016
2015
..
.
2000
1999
..
.
1984
1983
..
.
1968
122
120
119
116
115
112
7D0FFFh
7CFFFFh
..
.
108
7C0FFFh
7BFFFFh
..
.
107
79FFFFh
..
.
105
1936
1935
..
.
1920
1919
..
.
1903
..
.
1887
..
.
1872
1871
..
.
1856
1855
..
.
7A0000h
790000h
78F000h
..
.
780000h
77F000h
..
.
770000h
76F000h
..
.
760000h
75F000h
..
.
750000h
74F000h
..
.
740000h
73F000h
..
.
730000h
790FFFh
78FFFFh
..
.
104
780FFFh
77FFFFh
..
.
103
76FFFFh
..
.
102
75FFFFh
..
.
101
750FFFh
74FFFFh
..
.
100
740FFFh
73FFFFh
..
.
99
98
1823
..
.
71F000h
..
.
71FFFFh
..
.
97
700000h
6E0FFFh
6DFFFFh
..
.
1728
1727
..
.
6C0000h
6BF000h
..
.
6C0FFFh
6BFFFFh
..
.
1744
1743
..
.
710FFFh
70FFFFh
..
.
96
700FFFh
13
6B0000h
6D0FFFh
6CFFFFh
..
.
6B0FFFh
6AF000h
..
.
6AFFFFh
..
.
1695
..
.
69F000h
..
.
69FFFFh
..
.
1664
1663
..
.
680000h
67F000h
..
.
680FFFh
67FFFFh
..
.
1680
1679
..
.
6A0000h
690000h
68F000h
..
.
670000h
6A0FFFh
690FFFh
68FFFFh
..
.
670FFFh
1647
..
.
66F000h
..
.
66FFFFh
..
.
1631
..
.
65F000h
..
.
65FFFFh
..
.
1600
1599
..
.
640000h
63F000h
..
.
640FFFh
63FFFFh
..
.
1616
1615
..
.
660000h
650000h
64F000h
..
.
630000h
660FFFh
650FFFh
64FFFFh
..
.
630FFFh
1583
..
.
62F000h
..
.
62FFFFh
..
.
1567
..
.
61F000h
..
.
61FFFFh
..
.
1536
600000h
600FFFh
1568
720FFFh
6D0000h
6CF000h
..
.
1711
..
.
1584
730FFFh
72FFFFh
..
.
710000h
70F000h
..
.
6E0000h
6DF000h
..
.
1632
760FFFh
Address Range
6FF000h
6FFFFFh
..
..
.
.
6F0000h
6F0FFFh
6EF000h
6EFFFFh
..
..
.
.
1760
1759
..
.
1648
770FFFh
72F000h
..
.
1808
1807
..
.
1776
1775
..
.
1696
7A0FFFh
1839
..
.
720000h
Sector
1791
..
.
1712
7B0FFFh
79F000h
..
.
1792
P/N: PM1290
7B0000h
109
1951
..
.
1824
113
7C0000h
7BF000h
..
.
7E0FFFh
7DFFFFh
..
.
106
1840
114
7D0000h
7CF000h
..
.
110
7AFFFFh
..
.
1888
117
7E0000h
7DF000h
..
.
111
7AF000h
..
.
1904
118
Address Range
7FF000h
7FFFFFh
..
..
.
.
7F0000h
7F0FFFh
7EF000h
7EFFFFh
..
..
.
.
1967
..
.
1952
121
Block
1552
1551
..
.
620000h
610000h
60F000h
..
.
620FFFh
610FFFh
60FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Block
95
94
93
92
91
Sector
1535
..
.
1520
1519
..
.
1504
1503
..
.
1488
1487
..
.
1472
1471
..
.
1456
90
88
87
84
83
80
P/N: PM1290
5D0FFFh
5CFFFFh
..
.
76
5C0FFFh
5BFFFFh
..
.
75
59FFFFh
..
.
1408
1407
..
.
580000h
57F000h
..
.
580FFFh
57FFFFh
..
.
71
1424
1423
..
.
5A0000h
590000h
58F000h
..
.
570000h
74
73
590FFFh
58FFFFh
..
.
72
56FFFFh
..
.
70
1375
..
.
55F000h
..
.
55FFFFh
..
.
69
1344
1343
..
.
550000h
54F000h
..
.
540000h
53F000h
..
.
530000h
550FFFh
54FFFFh
..
.
67
66
52FFFFh
..
.
1311
..
.
51F000h
..
.
51FFFFh
..
.
1280
500000h
500FFFh
1296
1295
..
.
510000h
50F000h
..
.
4E0FFFh
4DFFFFh
..
.
1216
1215
..
.
4C0000h
4BF000h
..
.
4C0FFFh
4BFFFFh
..
.
1232
1231
..
.
65
510FFFh
50FFFFh
..
.
64
14
4B0000h
4D0FFFh
4CFFFFh
..
.
4B0FFFh
4AF000h
..
.
4AFFFFh
..
.
1183
..
.
49F000h
..
.
49FFFFh
..
.
1152
1151
..
.
480000h
47F000h
..
.
480FFFh
47FFFFh
..
.
1168
1167
..
.
4A0000h
490000h
48F000h
..
.
470000h
4A0FFFh
490FFFh
48FFFFh
..
.
470FFFh
1135
..
.
46F000h
..
.
46FFFFh
..
.
1119
..
.
45F000h
..
.
45FFFFh
..
.
1088
1087
..
.
440000h
43F000h
..
.
440FFFh
43FFFFh
..
.
1104
1103
..
.
460000h
450000h
44F000h
..
.
430000h
460FFFh
450FFFh
44FFFFh
..
.
430FFFh
1071
..
.
42F000h
..
.
42FFFFh
..
.
1055
..
.
41F000h
..
.
41FFFFh
..
.
1024
400000h
400FFFh
1056
520FFFh
4D0000h
4CF000h
..
.
1119
..
.
1072
530FFFh
52F000h
..
.
520000h
68
540FFFh
53FFFFh
..
.
1327
..
.
4E0000h
4DF000h
..
.
1120
560FFFh
Address Range
4FF000h
4FFFFFh
..
..
.
.
4F0000h
4F0FFFh
4EF000h
4EFFFFh
..
..
.
.
1248
1247
..
.
1136
570FFFh
56F000h
..
.
1360
1359
..
.
1264
1263
..
.
1184
5A0FFFh
1391
..
.
560000h
Sector
1279
..
.
1200
5B0FFFh
59F000h
..
.
1312
81
5B0000h
77
1439
..
.
1328
82
5C0000h
5BF000h
..
.
5E0FFFh
5DFFFFh
..
.
5AFFFFh
..
.
1376
85
5D0000h
5CF000h
..
.
78
5AF000h
..
.
1392
86
5E0000h
5DF000h
..
.
79
1455
..
.
1440
89
Block
Address Range
5FF000h
5FFFFFh
..
..
.
.
5F0000h
5F0FFFh
5EF000h
5EFFFFh
..
..
.
.
1040
1039
..
.
420000h
410000h
40F000h
..
.
420FFFh
410FFFh
40FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Block
63
62
61
60
59
Sector
1023
..
.
1008
1007
..
.
992
991
..
.
976
975
..
.
960
959
..
.
944
58
56
55
52
51
3C0000h
3BF000h
..
.
3B0000h
3E0FFFh
3DFFFFh
..
.
44
3C0FFFh
3BFFFFh
..
.
43
3B0FFFh
39FFFFh
..
.
896
895
..
.
380000h
37F000h
..
.
380FFFh
37FFFFh
..
.
39
912
911
..
.
390000h
38F000h
..
.
370000h
42
3A0FFFh
41
390FFFh
38FFFFh
..
.
40
370FFFh
36FFFFh
..
.
38
863
..
.
35F000h
..
.
35FFFFh
..
.
37
832
831
..
.
350000h
34F000h
..
.
340000h
33F000h
..
.
330000h
360FFFh
35
34
330FFFh
32F000h
..
.
32FFFFh
..
.
49
799
..
.
31F000h
..
.
31FFFFh
..
.
768
300000h
300FFFh
800
784
783
..
.
320000h
310000h
30F000h
..
.
36
340FFFh
33FFFFh
..
.
815
..
.
2E0000h
2DF000h
..
.
2E0FFFh
2DFFFFh
..
.
704
703
..
.
2C0000h
2BF000h
..
.
2C0FFFh
2BFFFFh
..
.
720
719
..
.
310FFFh
30FFFFh
..
.
32
15
2B0FFFh
2AFFFFh
..
.
671
..
.
29F000h
..
.
29FFFFh
..
.
640
639
..
.
280000h
27F000h
..
.
280FFFh
27FFFFh
..
.
656
655
..
.
2A0000h
290000h
28F000h
..
.
270000h
2A0FFFh
290FFFh
28FFFFh
..
.
270FFFh
623
..
.
26F000h
..
.
26FFFFh
..
.
607
..
.
25F000h
..
.
25FFFFh
..
.
576
575
..
.
240000h
23F000h
..
.
240FFFh
23FFFFh
..
.
592
591
..
.
260000h
250000h
24F000h
..
.
230000h
260FFFh
250FFFh
24FFFFh
..
.
230FFFh
559
..
.
22F000h
..
.
22FFFFh
..
.
543
..
.
21F000h
..
.
21FFFFh
..
.
512
200000h
200FFFh
544
33
2B0000h
2D0FFFh
2CFFFFh
..
.
2AF000h
..
.
560
320FFFh
2D0000h
2CF000h
..
.
687
..
.
608
350FFFh
34FFFFh
..
.
Address Range
2FF000h
2FFFFFh
..
..
.
.
2F0000h
2F0FFFh
2EF000h
2EFFFFh
..
..
.
.
736
735
..
.
624
36F000h
..
.
848
847
..
.
752
751
..
.
672
879
..
.
360000h
Sector
767
..
.
688
39F000h
..
.
3A0000h
50
P/N: PM1290
45
3D0FFFh
3CFFFFh
..
.
927
..
.
816
48
46
3AFFFFh
..
.
864
53
3D0000h
3CF000h
..
.
47
3AF000h
..
.
880
54
3E0000h
3DF000h
..
.
Block
943
..
.
928
57
Address Range
3FF000h
3FFFFFh
..
..
.
.
3F0000h
3F0FFFh
3EF000h
3EFFFFh
..
..
.
.
528
527
..
.
220000h
210000h
20F000h
..
.
220FFFh
210FFFh
20FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Block
31
30
29
28
27
Sector
511
..
.
496
495
..
.
480
479
..
.
464
463
..
.
448
447
..
.
432
26
431
..
.
416
25
24
23
415
..
.
400
399
..
.
384
383
..
.
368
22
20
19
16
1B0000h
1AF000h
..
.
1A0000h
19F000h
..
.
190000h
18F000h
..
.
180000h
17F000h
..
.
170000h
320
319
..
.
150000h
14F000h
..
.
140000h
13F000h
..
.
130000h
110000h
10F000h
..
.
100000h
0E0FFFh
0DFFFFh
..
.
192
191
..
.
0C0000h
0BF000h
..
.
0C0FFFh
0BFFFFh
..
.
208
207
..
.
09FFFFh
..
.
7
128
127
..
.
080000h
07F000h
..
.
080FFFh
07FFFFh
..
.
6
111
..
.
06F000h
..
.
06FFFFh
..
.
95
..
.
05F000h
..
.
05FFFFh
..
.
64
63
..
.
040000h
03F000h
..
.
040FFFh
03FFFFh
..
.
5
4
3
144
143
..
.
80
79
..
.
48
2
130FFFh
1
0
100FFFh
16
090000h
08F000h
..
.
070000h
060000h
050000h
04F000h
..
.
030000h
0A0FFFh
090FFFh
08FFFFh
..
.
070FFFh
060FFFh
050FFFh
04FFFFh
..
.
030FFFh
02F000h
..
.
02FFFFh
..
.
31
..
.
01F000h
..
.
01FFFFh
..
.
4
3
2
1
0
004000h
003000h
002000h
001000h
000000h
004FFFh
003FFFh
002FFFh
001FFFh
000FFFh
16
15
..
.
120FFFh
0A0000h
47
..
.
32
110FFFh
10FFFFh
..
.
0B0FFFh
09F000h
..
.
96
140FFFh
13FFFFh
..
.
0B0000h
0D0FFFh
0CFFFFh
..
.
159
..
.
112
150FFFh
14FFFFh
..
.
0D0000h
0CF000h
..
.
0AFFFFh
..
.
8
160FFFh
11FFFFh
..
.
0E0000h
0DF000h
..
.
0AF000h
..
.
9
170FFFh
11F000h
..
.
224
223
..
.
160
180FFFh
17FFFFh
..
.
287
..
.
240
239
..
.
Address Range
0FF000h
0FFFFFh
..
..
.
.
0F0000h
0F0FFFh
0EF000h
0EFFFFh
..
..
.
.
175
..
.
10
190FFFh
18FFFFh
..
.
12FFFFh
..
.
Sector
255
..
.
176
19FFFFh
..
.
12F000h
..
.
272
271
..
.
11
1A0FFFh
303
..
.
120000h
12
1B0FFFh
15FFFFh
..
.
336
335
..
.
13
1AFFFFh
..
.
15F000h
..
.
160000h
14
1C0FFFh
1BFFFFh
..
.
351
..
.
256
P/N: PM1290
1C0000h
1BF000h
..
.
15
1D0FFFh
1CFFFFh
..
.
16FFFFh
..
.
288
17
1D0000h
1CF000h
..
.
Block
1E0FFFh
1DFFFFh
..
.
16F000h
..
.
304
18
1E0000h
1DF000h
..
.
367
..
.
352
21
Address Range
1FF000h
1FFFFFh
..
..
.
.
1F0000h
1F0FFFh
1EF000h
1EFFFFh
..
..
.
.
020000h
010000h
00F000h
..
.
020FFFh
010FFFh
00FFFFh
..
.
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
DEVICE OPERATION
1. Before a command is issued, status register should be checked to ensure device is ready for the intended operation.
2. When incorrect command is inputted to this LSI, this LSI becomes standby mode and keeps the standby mode
until next CS# falling edge. In standby mode, SO pin of this LSI should be High-Z.
3. When correct command is inputted to this LSI, this LSI becomes active mode and keeps the active mode until
next CS# rising edge.
4. Input data is latched on the rising edge of Serial Clock(SCLK) and data shifts out on the falling edge of SCLK.
The difference of Serial mode 0 and mode 3 is shown as Figure 3.
5. For the following instructions: RDID, RDSR, RDSCUR, READ, FAST_READ, 2READ, RES, REMS and REMS2
the shifted-in instruction sequence is followed by a data-out sequence. After any bit of data being shifted out, the
CS# can be high. For the following instructions: WREN, WRDI, WRSR, SE, BE, CE, PP, CP, RDP, DP, ENSO,
EXSO,and WRSCUR, the CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
6. During the progress of Write Status Register, Program, Erase operation, to access the memory array is neglected and not affect the current operation of Write Status Register, Program, Erase.
Figure 3. Serial Modes Supported
CPOL
CPHA
(Serial mode 0)
0
0
SCLK
(Serial mode 3)
1
1
SCLK
SI
MSB
SO
MSB
Note:
CPOL indicates clock polarity of Serial master, CPOL=1 for SCLK high while idle, CPOL=0 for SCLK low while not
transmitting. CPHA indicates clock phase. The combination of CPOL bit and CPHA bit decides which Serial mode is
supported.
P/N: PM1290
17
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
COMMAND DESCRIPTION
(1) Write Enable (WREN)
The Write Enable (WREN) instruction is for setting Write Enable Latch (WEL) bit. For those instructions like PP,
CP, SE, BE, CE, and WRSR, which are intended to change the device content, should be set every time after the
WREN instruction setting the WEL bit.
The sequence of issuing WREN instruction is: CS# goes low→ sending WREN instruction code→ CS# goes high. (see
Figure 12)
(2) Write Disable (WRDI)
The Write Disable (WRDI) instruction is for resetting Write Enable Latch (WEL) bit.
The sequence of issuing WRDI instruction is: CS# goes low→ sending WRDI instruction code→ CS# goes high. (see
Figure 13)
The WEL bit is reset by following situations:
- Power-up
- Write Disable (WRDI) instruction completion
- Write Status Register (WRSR) instruction completion
- Page Program (PP) instruction completion
- Sector Erase (SE) instruction completion
- Block Erase (BE) instruction completion
- Chip Erase (CE) instruction completion
- Continuously program mode (CP) instruction completion
(3) Read Identification (RDID)
The RDID instruction is for reading the manufacturer ID of 1-byte and followed by Device ID of 2-byte. The MXIC
Manufacturer ID is C2(hex), the memory type ID is 20(hex) as the first-byte device ID, and the individual device ID
of second-byte ID are listed as table of "ID Definitions".
The sequence of issuing RDID instruction is: CS# goes low→ sending RDID instruction code → 24-bits ID data out
on SO → to end RDID operation can use CS# to high at any time during data out. (see Figure. 14)
While Program/Erase operation is in progress, it will not decode the RDID instruction, so there's no effect on the cycle of program/erase operation which is currently in progress. When CS# goes high, the device is at standby stage.
P/N: PM1290
18
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
(4) Read Status Register (RDSR)
The RDSR instruction is for reading Status Register Bits. The Read Status Register can be read at any time (even in
program/erase/write status register condition) and continuously. It is recommended to check the Write in Progress (WIP)
bit before sending a new instruction when a program, erase, or write status register operation is in progress.
The sequence of issuing RDSR instruction is: CS# goes low→ sending RDSR instruction code→ Status Register
data out on SO (see Figure. 15)
The definition of the status register bits is as below:
WIP bit. The Write in Progress (WIP) bit, a volatile bit, indicates whether the device is busy in program/erase/write
status register progress. When WIP bit sets to 1, which means the device is busy in program/erase/write status
register progress. When WIP bit sets to 0, which means the device is not in progress of program/erase/write status
register cycle.
WEL bit. The Write Enable Latch (WEL) bit, a volatile bit, indicates whether the device is set to internal write enable
latch. When WEL bit sets to 1, which means the internal write enable latch is set, the device can accept program/
erase/write status register instruction. When WEL bit sets to 0, which means no internal write enable latch; the device will not accept program/erase/write status register instruction. The program/erase command will be ignored and
not affect value of WEL bit if it is applied to a protected memory area.
BP3, BP2, BP1, BP0 bits. The Block Protect (BP3, BP2, BP1, BP0) bits, non-volatile bits, indicate the protected
area(as defined in table 1) of the device to against the program/erase instruction without hardware protection mode
being set. To write the Block Protect (BP3, BP2, BP1, BP0) bits requires the Write Status Register (WRSR) instruction to be executed. Those bits define the protected area of the memory to against Page Program (PP), Sector
Erase (SE), Block Erase (BE) and Chip Erase(CE) instructions (only if all Block Protect bits set to 0, the CE instruction can be executed).
Continuously Program Mode( CP mode) bit. The Continuously Program Mode bit indicates the status of CP
mode, "0" indicates not in CP mode; "1" indicates in CP mode.
SRWD bit. The Status Register Write Disable (SRWD) bit, non-volatile bit, is operated together with Write Protection (WP#/ACC) pin for providing hardware protection mode. The hardware protection mode requires SRWD sets
to 1 and WP#/ACC pin signal is low stage. In the hardware protection mode, the Write Status Register (WRSR)
instruction is no longer accepted for execution and the SRWD bit and Block Protect bits (BP3, BP2, BP1, BP0) are
read only.
Status Register
bit7
SRWD
(status register
write protect)
bit6
bit5
bit4
bit3
bit2
bit1
Continuously
BP3
BP2
BP1
BP0
WEL
program mode
(level of
(level of
(level of
(level of
(write enable
(CP mode)
protected block) protected block) protected block) protected block)
latch)
0 = normal
1= status
program mode
1= write enable
(note1)
(note1)
(note1)
(note1)
register write
1 = CP
0= not write
disable
mode(default 0)
enable
Non- volatile bit
volatile bit
Non- volatile bit Non- volatile bit Non- volatile bit Non- volatile bit
volatile bit
bit0
WIP
(write in
progress bit)
1= write
operation
0= not in write
operation
volatile bit
note1: see the table "Protected Area Sizes"
P/N: PM1290
19
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
(5) Write Status Register (WRSR)
The WRSR instruction is for changing the values of Status Register Bits. Before sending WRSR instruction, the
Write Enable (WREN) instruction must be decoded and executed to set the Write Enable Latch (WEL) bit in advance. The WRSR instruction can change the value of Block Protect (BP3, BP2, BP1, BP0) bits to define the protected area of memory (as shown in table 1). The WRSR also can set or reset the Status Register Write Disable (SRWD)
bit in accordance with Write Protection (WP#/ACC) pin signal. The WRSR instruction cannot be executed once the
Hardware Protected Mode (HPM) is entered.
The sequence of issuing WRSR instruction is: CS# goes low→ sending WRSR instruction code→ Status Register
data on SI→ CS# goes high. (see Figure 16)
The WRSR instruction has no effect on b6, b1, b0 of the status register.
The CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
The self-timed Write Status Register cycle time (tW) is initiated as soon as Chip Select (CS#) goes high. The Write
in Progress (WIP) bit still can be check out during the Write Status Register cycle is in progress. The WIP sets 1
during the tW timing, and sets 0 when Write Status Register Cycle is completed, and the Write Enable Latch (WEL)
bit is reset.
Table 6. Protection Modes
Mode
Software protection
mode(SPM)
Hardware protection
mode (HPM)
Status register condition
WP# and SRWD bit status
Memory
Status register can be written
in (WEL bit is set to "1") and
the SRWD, BP0-BP3
bits can be changed
WP#=1 and SRWD bit=0, or
WP#=0 and SRWD bit=0, or
WP#=1 and SRWD=1
The protected area cannot
be program or erase.
The SRWD, BP0-BP3 of
status register bits cannot be
changed
WP#=0, SRWD bit=1
The protected area cannot
be program or erase.
Note:
1. As defined by the values in the Block Protect (BP3, BP2, BP1, BP0) bits of the Status Register, as shown in Table 1.
As the above table showing, the summary of the Software Protected Mode (SPM) and Hardware Protected Mode (HPM).
Software Protected Mode (SPM):
- When SRWD bit=0, no matter WP#/ACC is low or high, the WREN instruction may set the WEL bit and can
change the values of SRWD, BP3, BP2, BP1, BP0. The protected area, which is defined by BP3, BP2, BP1,
BP0, is at software protected mode (SPM).
- When SRWD bit=1 and WP#/ACC is high, the WREN instruction may set the WEL bit can change the values of
SRWD, BP3, BP2, BP1, BP0. The protected area, which is defined by BP3, BP2, BP1, BP0, is at software protected mode (SPM)
P/N: PM1290
20
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Note: If SRWD bit=1 but WP#/ACC is low, it is impossible to write the Status Register even if the WEL bit has previously been set. It is rejected to write the Status Register and not be executed.
Hardware Protected Mode (HPM):
- When SRWD bit=1, and then WP#/ACC is low (or WP#/ACC is low before SRWD bit=1), it enters the hardware
protected mode (HPM). The data of the protected area is protected by software protected mode by BP3, BP2,
BP1, BP0 and hardware protected mode by the WP#/ACC to against data modification.
Note: to exit the hardware protected mode requires WP#/ACC driving high once the hardware protected mode is
entered. If the WP#/ACC pin is permanently connected to high, the hardware protected mode can never be entered;
only can use software protected mode via BP3, BP2, BP1, BP0.
(6) Read Data Bytes (READ)
The read instruction is for reading data out. The address is latched on rising edge of SCLK, and data shifts out on
the falling edge of SCLK at a maximum frequency fR. The first address byte can be at any location. The address
is automatically increased to the next higher address after each byte data is shifted out, so the whole memory can
be read out at a single READ instruction. The address counter rolls over to 0 when the highest address has been
reached.
The sequence of issuing READ instruction is: CS# goes low→ sending READ instruction code→ 3-byte address on
SI
→ data out on SO→ to end READ operation can use CS# to high at any time during data out. (see Figure.
17)
(7) Read Data Bytes at Higher Speed (FAST_READ)
The FAST_READ instruction is for quickly reading data out. The address is latched on rising edge of SCLK, and
data of each bit shifts out on the falling edge of SCLK at a maximum frequency fC. The first address byte can be at
any location. The address is automatically increased to the next higher address after each byte data is shifted out,
so the whole memory can be read out at a single FAST_READ instruction. The address counter rolls over to 0 when
the highest address has been reached.
The sequence of issuing FAST_READ instruction is: CS# goes low→ sending FAST_READ instruction code→
3-byte address on SI→ 1-dummy byte address on SI→data out on SO→ to end FAST_READ operation can use
CS# to high at any time during data out. (see Figure. 18)
While Program/Erase/Write Status Register cycle is in progress, FAST_READ instruction is rejected without any impact on the Program/Erase/Write Status Register current cycle.
(8) 2 x I/O Read Mode (2READ)
The 2READ instruction enable double throughput of Serial Flash in read mode. The address is latched on rising
edge of SCLK, and data of every two bits(interleave on 2 I/O pins) shift out on the falling edge of SCLK at a maximum frequency fT. The first address byte can be at any location. The address is automatically increased to the next
higher address after each byte data is shifted out, so the whole memory can be read out at a single 2READ instruction. The address counter rolls over to 0 when the highest address has been reached. Once writing 2READ instruction, the following address/dummy/data out will perform as 2-bit instead of previous 1-bit.
The sequence of issuing 2READ instruction is: CS# goes low→ sending 2READ instruction→ 24-bit address interleave on SIO1 & SIO0→ 8-bit dummy interleave on SIO1 & SIO0→ data out interleave on SIO1 & SIO0→ to end
2READ operation can use CS# to high at any time during data out (see Figure of 2 x I/O Read Mode Timing Waveform)
P/N: PM1290
21
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
While Program/Erase/Write Status Register cycle is in progress, 2READ instruction is rejected without any impact
on the Program/Erase/Write Status Register current cycle.
The 2 I/O only perform read operation. Program/Erase /Read ID/Read status/Read ID....operation do not support 2
I/O throughputs.
(9) Sector Erase (SE)
The Sector Erase (SE) instruction is for erasing the data of the chosen sector to be "1". The instruction is used for
any 4K-byte sector. A Write Enable (WREN) instruction must execute to set the Write Enable Latch (WEL) bit before sending the Sector Erase (SE). Any address of the sector (see table 3) is a valid address for Sector Erase (SE)
instruction. The CS# must go high exactly at the byte boundary (the latest eighth of address byte been latched-in);
otherwise, the instruction will be rejected and not executed.
Address bits [Am-A12] (Am is the most significant address) select the sector address.
The sequence of issuing SE instruction is: CS# goes low → sending SE instruction code→ 3-byte address on SI →
CS# goes high. (see Figure 22)
The self-timed Sector Erase Cycle time (tSE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Sector Erase cycle is in progress. The WIP sets 1 during the
tSE timing, and sets 0 when Sector Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the
page is protected by BP3, BP2, BP1, BP0 bits, the Sector Erase (SE) instruction will not be executed on the page.
(10) Block Erase (BE)
The Block Erase (BE) instruction is for erasing the data of the chosen block to be "1". The instruction is used for
64K-byte sector erase operation. A Write Enable (WREN) instruction must execute to set the Write Enable Latch (WEL)
bit before sending the Block Erase (BE). Any address of the block (see table 3) is a valid address for Block Erase (BE)
instruction. The CS# must go high exactly at the byte boundary (the latest eighth of address byte been latched-in);
otherwise, the instruction will be rejected and not executed.
The sequence of issuing BE instruction is: CS# goes low → sending BE instruction code→ 3-byte address on SI →
CS# goes high. (see Figure 23)
The self-timed Block Erase Cycle time (tBE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Sector Erase cycle is in progress. The WIP sets 1 during the
tBE timing, and sets 0 when Sector Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the
page is protected by BP3, BP2, BP1, BP0 bits, the Block Erase (BE) instruction will not be executed on the page.
(11) Chip Erase (CE)
The Chip Erase (CE) instruction is for erasing the data of the whole chip to be "1". A Write Enable (WREN) instruction must execute to set the Write Enable Latch (WEL) bit before sending the Chip Erase (CE). Any address of the
sector (see table 3) is a valid address for Chip Erase (CE) instruction. The CS# must go high exactly at the byte
boundary( the latest eighth of address byte been latched-in); otherwise, the instruction will be rejected and not executed.
The sequence of issuing CE instruction is: CS# goes low→ sending CE instruction code→ CS# goes high. (see
Figure 24)
P/N: PM1290
22
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
The self-timed Chip Erase Cycle time (tCE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Chip Erase cycle is in progress. The WIP sets 1 during the tCE
timing, and sets 0 when Chip Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the chip is
protected by BP3, BP2, BP1, BP0 bits, the Chip Erase (CE) instruction will not be executed. It will be only executed
when BP3, BP2, BP1, BP0 all set to "0".
(12) Page Program (PP)
The Page Program (PP) instruction is for programming the memory to be "0". A Write Enable (WREN) instruction
must execute to set the Write Enable Latch (WEL) bit before sending the Page Program (PP). If the eight least significant address bits (A7-A0) are not all 0, all transmitted data which goes beyond the end of the current page are
programmed from the start address if the same page (from the address whose 8 least significant address bits (A7A0) are all 0). The CS# must keep during the whole Page Program cycle. The CS# must go high exactly at the
byte boundary( the latest eighth of address byte been latched-in); otherwise, the instruction will be rejected and not
executed. If more than 256 bytes are sent to the device, the data of the last 256-byte is programmed at the request
page and previous data will be disregarded. If less than 256 bytes are sent to the device, the data is programmed at
the request address of the page without effect on other address of the same page.
The sequence of issuing PP instruction is: CS# goes low→ sending PP instruction code→ 3-byte address on SI→ at
least 1-byte on data on SI→ CS# goes high. (see Figure 20)
The self-timed Page Program Cycle time (tPP) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Page Program cycle is in progress. The WIP sets 1 during the
tPP timing, and sets 0 when Page Program Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the
page is protected by BP3, BP2, BP1, BP0 bits, the Page Program (PP) instruction will not be executed.
(13) Continuously program mode (CP mode)
The CP mode may enhance program performance by automatically increasing address to the next higher address
after each byte data has been programmed.
The Continuously program (CP) instruction is for multiple byte program to Flash. A write Enable (WREN) instruction must execute to set the Write Enable Latch(WEL) bit before sending the Continuously program (CP) instruction.
CS# requires to go high before CP instruction is executing. After CP instruction and address input, two bytes of data
is input sequentially from MSB(bit7) to LSB(bit0). The first byte data will be programmed to the initial address range
with A0=0 and second byte data with A0=1. If only one byte data is input, the CP mode will not process. If more
than two bytes data are input, the additional data will be ignored and only two byte data are valid. The CP program
instruction will be ignored and not affect the WEL bit if it is applied to a protected memory area. Any byte to be programmed should be in the erase state (FF) first. It will not roll over during the CP mode, once the last unprotected
address has been reached, the chip will exit CP mode and reset write Enable Latch bit (WEL) as "0" and CP mode
bit as "0". Please check the WIP bit status if it is not in write progress before entering next valid instruction. During
CP mode, the valid commands are CP command (AD hex), WRDI command (04 hex), RDSR command (05 hex),
RDPR command (A1 hex), and RDSCUR command (2B hex). And the WRDI command is valid after completion of a
CP programming cycle, which means the WIP bit=0.
The sequence of issuing CP instruction is : CS# high to low→ sending CP instruction code→ 3-byte address on SI→
Data Byte on SI→CS# goes high to low→ sending CP instruction......→ last desired byte programmed or sending
Write Disable (WRDI) instruction to end CP mode→ sending RDSR instruction to verify if CP mode is ended. (see
Figure of CP mode timing waveform)
Three methods to detect the completion of a program cycle during CP mode:
P/N: PM1290
23
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
1) Software method-I: by checking WIP bit of Status Register to detect the completion of CP mode.
2) Software method-II: by waiting for a tBP time out to determine if it may load next valid command or not.
3) Hardware method: by writing ESRY (enable SO to output RY/BY#) instruction to detect the completion of a
program cycle during CP mode. The ESRY instruction must be executed before CP mode execution. Once it is
enable in CP mode, the CS# goes low will drive out the RY/BY# status on SO, "0" indicates busy stage, "1" indicates ready stage, SO pin outputs tri-state if CS# goes high. DSRY (disable SO to output RY/BY#) instruction to
disable the SO to output RY/BY# and return to status register data output during CP mode. Please note that the
ESRY/DSRY command are not accepted unless the completion of CP mode.
(14) Deep Power-down (DP)
The Deep Power-down (DP) instruction is for setting the device on the minimizing the power consumption (to entering the Deep Power-down mode), the standby current is reduced from ISB1 to ISB2). The Deep Power-down mode
requires the Deep Power-down (DP) instruction to enter, during the Deep Power-down mode, the device is not active and all Write/Program/Erase instruction are ignored. When CS# goes high, it's only in standby mode not deep
power-down mode. It's different from Standby mode.
The sequence of issuing DP instruction is: CS# goes low→ sending DP instruction code→ CS# goes high. (see Figure 25)
Once the DP instruction is set, all instruction will be ignored except the Release from Deep Power-down mode (RDP)
and Read Electronic Signature (RES) instruction. (those instructions allow the ID being reading out). When Powerdown, the deep power-down mode automatically stops, and when power-up, the device automatically is in standby
mode. For RDP instruction the CS# must go high exactly at the byte boundary (the latest eighth bit of instruction
code been latched-in); otherwise, the instruction will not executed. As soon as Chip Select (CS#) goes high, a delay
of tDP is required before entering the Deep Power-down mode and reducing the current to ISB2.
(15) Release from Deep Power-down (RDP), Read Electronic Signature (RES)
The Release from Deep Power-down (RDP) instruction is terminated by driving Chip Select (CS#) High. When Chip
Select (CS#) is driven High, the device is put in the Stand-by Power mode. If the device was not previously in the
Deep Power-down mode, the transition to the Stand-by Power mode is immediate. If the device was previously in
the Deep Power-down mode, though, the transition to the Stand-by Power mode is delayed by tRES2, and Chip
Select (CS#) must remain High for at least tRES2(max), as specified in Table 6. Once in the Stand-by Power mode,
the device waits to be selected, so that it can receive, decode and execute instructions.
RES instruction is for reading out the old style of 8-bit Electronic Signature, whose values are shown as table of ID
Definitions. This is not the same as RDID instruction. It is not recommended to use for new design. For new design,
please use RDID instruction. Even in Deep power-down mode, the RDP and RES are also allowed to be executed,
only except the device is in progress of program/erase/write cycle; there's no effect on the current program/erase/
write cycle in progress.
The sequence is shown as Figure 26,27.
The RES instruction is ended by CS# goes high after the ID been read out at least once. The ID outputs repeatedly if continuously send the additional clock cycles on SCLK while CS# is at low. If the device was not previously
in Deep Power-down mode, the device transition to standby mode is immediate. If the device was previously in
Deep Power-down mode, there's a delay of tRES2 to transit to standby mode, and CS# must remain to high at least
tRES2(max). Once in the standby mode, the device waits to be selected, so it can be receive, decode, and execute
instruction.
The RDP instruction is for releasing from Deep Power Down Mode.
P/N: PM1290
24
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
(16) Read Electronic Manufacturer ID & Device ID (REMS), (REMS2)
The REMS & REMS2 instruction is an alternative to the Release from Power-down/Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID.
The REMS & REMS2 instruction is very similar to the Release from Power-down/Device ID instruction. The instruction is initiated by driving the CS# pin low and shift the instruction code "90h" or "EFh" followed by two dummy bytes
and one bytes address (A7~A0). After which, the Manufacturer ID for MXIC (C2h) and the Device ID are shifted out
on the falling edge of SCLK with most significant bit (MSB) first as shown in figure 25. The Device ID values are
listed in Table of ID Definitions. If the one-byte address is initially set to 01h, then the device ID will be read first and
then followed by the Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from
one to the other. The instruction is completed by driving CS# high.
Table 7. ID Definitions
Command Type
MX25L1605D
manufacturer memory memory
ID
type
density
RDID Command
C2
20
15
electronic ID
RES Command
14
device
manufacturer
ID
ID
REMS/REMS2
C2
14
MX25L3205D
memory
manufacturer memory
ID
type
density
C2
20
16
electronic ID
15
manufacturer
ID
device ID
C2
15
MX25L6405D
memory
manufacturer memory
ID
type
density
C2
20
17
electronic ID
16
manufacturer device ID
ID
C2
16
(17) Enter Secured OTP (ENSO)
The ENSO instruction is for entering the additional 512-bit secured OTP mode. The additional 512-bit secured OTP
is independent from main array, which may use to store unique serial number for system identifier. After entering the
Secured OTP mode, and then follow standard read or program, procedure to read out the data or update data. The
Secured OTP data cannot be updated again once it is lock-down.
The sequence of issuing ENSO instruction is: CS# goes low→ sending ENSO instruction to enter Secured OTP
mode → CS# goes high.
Please note that WRSR/WRSCUR commands are not acceptable during the access of secure OTP region, once security OTP is lock down, only read related commands are valid.
(18) Exit Secured OTP (EXSO)
The EXSO instruction is for exiting the additional 512-bit secured OTP mode.
The sequence of issuing EXSO instruction is: CS# goes low→ sending EXSO instruction to exit Secured OTP
mode→ CS# goes high.
P/N: PM1290
25
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
(19) Read Security Register (RDSCUR)
The RDSCUR instruction is for reading the value of Security Register bits. The Read Security Register can be read
at any time (even in program/erase/write status register/write security register condition) and continuously.
The sequence of issuing RDSCUR instruction is : CS# goes low→ send ing RDSCUR instruction → Security Register data out on SO→ CS# goes high.
The definition of the Security Register bits is as below:
Secured OTP Indicator bit. The Secured OTP indicator bit shows the chip is locked by factory before ex- factory or
not. When it is "0", it indicates non- factory lock; "1" indicates factory- lock.
Lock-down Secured OTP (LDSO) bit. By writing WRSCUR instruction, the LDSO bit may be set to "1" for customer lock-down purpose. However, once the bit is set to "1" (lock-down), the LDSO bit and the 512-bit Secured OTP
area cannot be update any more. While it is in 512-bit secured OTP mode, array access is not allowed.
Table 8. Security Register Definition
bit7
bit6
bit5
bit4
bit3
bit2
x
x
x
x
x
x
reserved
reserved
reserved
reserved
reserved
reserved
volatile bit
volatile bit
volatile bit
volatile bit
volatile bit
volatile bit
bit1
bit0
LDSO
(indicate if
Secrured OTP
lock-down
indicator bit
0 = not lockdown
0 = non1 = lock-down
factory lock
(cannot
1 = factory
program/erase
lock
OTP)
non-volatile bit non-volatile bit
(20) Write Security Register (WRSCUR)
The WRSCUR instruction is for changing the values of Security Register Bits. Unlike write status register, the WREN
instruction is not required before sending WRSCUR instruction. The WRSCUR instruction may change the values
of bit1 (LDSO bit) for customer to lock-down the 512-bit Secured OTP area. Once the LDSO bit is set to "1", the Secured OTP area cannot be updated any more.
The sequence of issuing WRSCUR instruction is :CS# goes low→ sending WRSCUR instruction → CS# goes high.
The CS# must go high exactly at the boundary; otherwise, the instruction will be rejected and not executed.
P/N: PM1290
26
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
POWER-ON STATE
The device is at below states when power-up:
- Standby mode ( please note it is not deep power-down mode)
- Write Enable Latch (WEL) bit is reset
The device must not be selected during power-up and power-down stage unless the VCC achieves below correct
level:
- VCC minimum at power-up stage and then after a delay of tVSL
- GND at power-down
Please note that a pull-up resistor on CS# may ensure a safe and proper power-up/down level.
An internal power-on reset (POR) circuit may protect the device from data corruption and inadvertent data change
during power up state.
For further protection on the device, if the VCC does not reach the VCC minimum level, the correct operation is not
guaranteed. The read, write, erase, and program command should be sent after the below time delay:
- tVSL after VCC reached VCC minimum level
The device can accept read command after VCC reached VCC minimum and a time delay of tVSL.
Please refer to the figure of "power-up timing".
Note:
- To stabilize the VCC level, the VCC rail decoupled by a suitable capacitor close to package pins is recommended.(generally around 0.1uF)
P/N: PM1290
27
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
ELECTRICAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
RATING
VALUE
Ambient Operating Temperature
-40°C to 85°C for Industrial grade
Storage Temperature
-55°C to 125°C
Applied Input Voltage
-0.5V to 4.6V
Applied Output Voltage
-0.5V to 4.6V
VCC to Ground Potential
-0.5V to 4.6V
NOTICE:
1.Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to
the device. This is stress rating only and functional operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended period may affect reliability.
2.Specifications contained within the following tables are subject to change.
3.During voltage transitions, all pins may overshoot Vss to -2.0V and Vcc to +2.0V for periods up to 20ns, see Figure 4, 5.
Figure 4.Maximum Negative Overshoot Waveform Figure 5. Maximum Positive Overshoot Waveform
20ns
20ns
20ns
Vss
Vcc + 2.0V
Vss - 2.0V
Vcc
20ns
20ns
20ns
CAPACITANCE TA = 25°C, f = 1.0 MHz
SYMBOL
CIN
COUT
P/N: PM1290
PARAMETER
Input Capacitance
Output Capacitance
MIN.
TYP
28
MAX.
6
8
UNIT
pF
pF
CONDITIONS
VIN = 0V
VOUT = 0V
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 6. INPUT TEST WAVEFORMS AND MEASUREMENT LEVEL
Input timing referance level
0.8VCC
0.2VCC
Output timing referance level
0.7VCC
AC
Measurement
Level
0.3VCC
0.5VCC
Note: Input pulse rise and fall time are <5ns
Figure 7. OUTPUT LOADING
DEVICE UNDER
TEST
2.7K ohm
CL
6.2K ohm
+3.3V
DIODES=IN3064
OR EQUIVALENT
CL=30pF Including jig capacitance
(CL=15pF Including jig capacitance for 86MHz and 50MHz@2x I/O)
P/N: PM1290
29
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 9. DC CHARACTERISTICS (Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V)
SYMBOL PARAMETER
NOTES
MIN.
TYP.
MAX.
UNITS TEST CONDITIONS
ILI
Input Load Current
1
±2
uA
VCC = VCC Max,
VIN = VCC or GND
ILO
Output Leakage Current
1
±2
uA
VCC = VCC Max,
VIN = VCC or GND
35
uA
WP#/ACC=10.5V
20
uA
VIN = VCC or GND,
CS# = VCC
20
uA
VIN = VCC or GND,
CS# = VCC
25
mA
f=86MHz
fT=50MHz (2 x I/O read)
SCLK=0.1VCC/0.9VCC,
SO=Open
20
mA
f=66MHz,
SCLK=0.1VCC/0.9VCC,
SO=Open
10
mA
f=33MHz,
SCLK=0.1VCC/0.9VCC,
SO=Open
20
mA
20
mA
1
20
mA
Erase in Progress, CS#=VCC
1
20
mA
Erase in Progress, CS#=VCC
9.5
10.5
V
ILIHV
HV pin input Leakage
Current
ISB1
VCC Standby Current
ISB2
Deep Power-down
Current
ICC1
ICC2
ICC3
ICC4
ICC5
VHH
VCC Read
VCC Program Current
(PP)
VCC Write Status
Register (WRSR) Current
VCC Sector Erase
Current (SE)
VCC Chip Erase Current
(CE)
Voltage for ACC Program/
Erase Acceleration
1
1
1
Program in Progress,
CS# = VCC
Program status register in
progress, CS#=VCC
VCC=2.7V~3.6V
VIL
Input Low Voltage
-0.5
0.3VCC
V
VIH
Input High Voltage
0.7VCC
VCC+0.4
V
VOL
Output Low Voltage
0.4
V
IOL = 1.6mA
VOH
Output High Voltage
V
IOH = -100uA
P/N: PM1290
VCC-0.2
30
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 10. AC CHARACTERISTICS (Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V)
Symbol
Alt. Parameter
Min.
fSCLK
fC
Clock Frequency for the following instructions:
FAST_READ, PP, SE, BE, CE, DP, RES,RDP
WREN, WRDI, RDID, RDSR, WRSR
fRSCLK
fR
fT
Clock Frequency for READ instructions
Clock Frequency for 2READ instructions
fTSCLK
tCH(1)
tCLH Clock High Time
tCL(1)
tCLL Clock Low Time
fc=86MHz
fR=33MHz
fc=86MHz
fR=33MHz
tCLCH(2)
Clock Rise Time (3) (peak to peak)
tCHCL(2)
Clock Fall Time (3) (peak to peak)
tSLCH tCSS CS# Active Setup Time (relative to SCLK)
tCHSL
CS# Not Active Hold Time (relative to SCLK)
tDVCH tDSU Data In Setup Time
tCHDX
tDH Data In Hold Time
tCHSH
CS# Active Hold Time (relative to SCLK)
tSHCH
CS# Not Active Setup Time (relative to SCLK)
tSHSL tCSH CS# Deselect Time
64Mb/ 2.7V-3.6V
tSHQZ(2) tDIS Output Disable Time
32Mb/
3.0V-3.6V
16Mb
64Mb/ 2.7V-3.6V
Clock Low to Output Valid
tCLQV
tV
32Mb/
16Mb 3.0V-3.6V
tCLQX
tHO Output Hold Time
tHLCH
HOLD# Setup Time (relative to SCLK)
tCHHH
HOLD# Hold Time (relative to SCLK)
tHHCH
HOLD Setup Time (relative to SCLK)
tCHHL
HOLD Hold Time (relative to SCLK)
tHHQX(2) tLZ
64Mb/
2.7V-3.6V
HOLD to Output Low-Z
32Mb/
3.0V-3.6V
16Mb
tHLQZ(2) tHZ
64Mb/
2.7V-3.6V
HOLD# to Output High-Z
32Mb/
3.0V-3.6V
16Mb
tWHSL(4)
Write Protect Setup Time
tSHWL (4)
Write Protect Hold Time
tDP(2)
CS# High to Deep Power-down Mode
CS# High to Standby Mode without Electronic
tRES1(2)
Signature Read
CS# High to Standby Mode with Electronic Signature
tRES2(2)
Read
P/N: PM1290
31
10KHz
10KHz
10KHz
5.5
13
5.5
13
0.1
0.1
5
5
2
5
5
5
40
0
5
5
5
5
20
100
Typ.
Max.
86
(Condition:15pF)
66
(Condition:30pF)
33
50
(Condition:15pF)
Unit
MHz
MHz
MHz
MHz
10
ns
ns
ns
ns
V/ns
V/ns
ns
ns
ns
ns
ns
ns
ns
ns
8
ns
10
ns
8
ns
10
8
ns
ns
ns
ns
ns
ns
ns
10
8
ns
ns
10
ns
ns
us
8.8
us
8.8
us
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Symbol
tW
tBP
Alt. Parameter
Write Status Register Cycle Time
Byte-Program
tPP
tSE
tBE
Page Program Cycle Time
Sector Erase Cycle Time
Block Erase Cycle Time
tCE
Chip Erase Cycle Time
Min.
64Mb
32Mb
16Mb
Typ.
40
Max.
100
Unit
ms
9
300
us
1.4
60
0.7
50
25
14
5
300
2
80
50
30
ms
ms
s
s
s
s
Notes:
1. tCH + tCL must be greater than or equal to 1/ fC. For Fast Read, tCL/tCH=5.5/5.5.
2. Value guaranteed by characterization, not 100% tested in production.
3. Expressed as a slew-rate.
4. Only applicable as a constraint for a WRSR instruction when SRWD is set at 1.
5. Test condition is shown as Figure 6.
P/N: PM1290
32
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Table 11. Power-Up Timing
Symbol
Parameter
Min.
tVSL(1)
VCC(min) to CS# low
200
Max.
Unit
us
Note: 1. The parameter is characterized only.
INITIAL DELIVERY STATE
The device is delivered with the memory array erased: all bits are set to 1 (each byte contains FFh). The Status
Register contains 00h (all Status Register bits are 0).
P/N: PM1290
33
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 8. Serial Input Timing
tSHSL
CS#
tCHSL
tSLCH
tCHSH
tSHCH
SCLK
tDVCH
tCHCL
tCHDX
tCLCH
LSB
MSB
SI
High-Z
SO
Figure 9. Output Timing
CS#
tCH
SCLK
tCLQV
tCLQX
tCL
tCLQV
tSHQZ
tCLQX
LSB
SO
tQLQH
tQHQL
SI
P/N: PM1290
ADDR.LSB IN
34
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 10. Hold Timing
CS#
tHLCH
tCHHL
tHHCH
SCLK
tCHHH
tHLQZ
tHHQX
SO
HOLD#
* SI is "don't care" during HOLD operation.
Figure 11. WP# Disable Setup and Hold Timing during WRSR when SRWD=1
WP#
tSHWL
tWHSL
CS#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCLK
01
SI
SO
P/N: PM1290
High-Z
35
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 12. Write Enable (WREN) Sequence (Command 06)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
06
High-Z
SO
Figure 13. Write Disable (WRDI) Sequence (Command 04)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
04
High-Z
SO
Figure 14. Read Identification (RDID) Sequence (Command 9F)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
28 29 30 31
SCLK
Command
SI
9F
Manufacturer Identification
SO
High-Z
7
6
5
MSB
P/N: PM1290
3
2
1
Device Identification
0 15 14 13
3
2
1
0
MSB
36
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 15. Read Status Register (RDSR) Sequence (Command 05)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
05
SI
Status Register Out
High-Z
SO
7
6
5
4
3
2
Status Register Out
1
0
7
6
5
4
3
2
1
0
7
MSB
MSB
Figure 16. Write Status Register (WRSR) Sequence (Command 01)
CS#
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
SCLK
command
SI
Status
Register In
01
7
5
4
3
2
0
1
MSB
High-Z
SO
6
Figure 17. Read Data Bytes (READ) Sequence (Command 03)
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31 32 33 34 35 36 37 38 39
SCLK
command
SI
03
24-Bit Address
23 22 21
3
2
1
0
MSB
SO
Data Out 1
High-Z
7
6
5
4
3
2
Data Out 2
1
0
7
MSB
P/N: PM1290
37
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 18. Read at Higher Speed (FAST_READ) Sequence (Command 0B)
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31
SCLK
Command
SI
SO
24 BIT ADDRESS
23 22 21
0B
3
2
1
0
High-Z
CS#
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCLK
Dummy Byte
SI
7
6
5
4
3
2
1
0
DATA OUT 2
DATA OUT 1
SO
7
6
5
3
2
1
0
7
MSB
MSB
P/N: PM1290
4
38
6
5
4
3
2
1
0
7
MSB
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 19. 2 x I/O Read Mode Sequence (Command BB)
CS#
0
1
2
3
4
5
6
7
8
18 19 20 21 22 23 24 25 26 27
9 10 11
SCLK
BB(hex)
SI/SIO0
High Impedance
SO/SIO1
address
bit22, bit20, bit18...bit0
dummy
data
bit6, bit4, bit2...bit0, bit6, bit4....
address
bit23, bit21, bit19...bit1
dummy
data
bit7, bit5, bit3...bit1, bit7, bit5....
Figure 20. Page Program (PP) Sequence (Command 02)
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31 32 33 34 35 36 37 38 39
SCLK
1
0
7
6
5
3
2
1
0
2079
2
2078
3
2077
23 22 21
02
SI
Data Byte 1
2076
24-Bit Address
2075
Command
4
1
0
MSB
MSB
2074
2073
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
2072
CS#
SCLK
Data Byte 2
SI
7
6
MSB
P/N: PM1290
5
4
3
2
Data Byte 3
1
0
7
6
5
4
MSB
3
2
Data Byte 256
1
0
7
6
5
4
3
2
MSB
39
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 21. Continously Program (CP) Mode Sequence with Hardware Detection (Command AD)
CS#
0 1
6 7 8 9
30 31 31 32
0 1
47 48
6 7 8
20 21 22 23 24
0
7
0
7 8
SCLK
Command
SI
S0
AD (hex)
data in
Byte n-1, Byte n
Valid
Command (1)
data in
Byte 0, Byte1
24-bit address
high impedance
04 (hex)
05 (hex)
status (2)
Note: (1) During CP mode, the valid commands are CP command (AD hex), WRDI command (04 hex), RDSR command (05 hex), RDPR command (A1 hex), and RDSCUR command (2B hex).
(2) Once an internal programming operation begins, CS# goes low will drive the status on the SO pin and
CS# goes high will return the SO pin to tri-state.
(3) To end the CP mode, either reaching the highest unprotected address or sending Write Disable (WRDI)
command (04 hex) may achieve it and then it is recommended to send RDSR command (05 hex) to verify if
CP mode ends.
Figure 22. Sector Erase (SE) Sequence (Command 20)
CS#
0
1
2
3
4
5
6
7
8
9
29 30 31
SCLK
24 Bit Address
Command
SI
23 22
20
2
1
0
MSB
Note: SE command is 20(hex).
Figure 23. Block Erase (BE) Sequence (Command D8)
CS#
0
1
2
3
4
5
6
7
8
9
29 30 31
SCLK
Command
SI
24 Bit Address
23 22
D8
2
1
0
MSB
Note: BE command is D8(hex).
P/N: PM1290
40
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 24. Chip Erase (CE) Sequence (Command 60 or C7)
CS#
0
1
2
3
4
5
6
7
SCLK
Command
SI
60 or C7
Note: CE command is 60(hex) or C7(hex).
Figure 25. Deep Power-down (DP) Sequence (Command B9)
CS#
0
1
2
3
4
5
6
tDP
7
SCLK
Command
B9
SI
Deep Power-down Mode
Stand-by Mode
Figure 26. Release from Deep Power-down and Read Electronic Signature (RES) Sequence (Command AB)
CS#
0
1
2
3
4
5
6
7
8
9 10
28 29 30 31 32 33 34 35 36 37 38
SCLK
Command
SI
AB
tRES2
3 Dummy Bytes
23 22 21
3
2
1
0
MSB
SO
Electronic Signature Out
High-Z
7
6
5
4
3
2
1
0
MSB
Deep Power-down Mode
P/N: PM1290
41
Stand-by Mode
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 27. Release from Deep Power-down (RDP) Sequence (Command AB)
CS#
0
1
2
3
4
5
6
tRES1
7
SCLK
Command
SI
AB
High-Z
SO
Deep Power-down Mode
Stand-by Mode
Figure 28. Read Electronic Manufacturer & Device ID (REMS) Sequence (Command 90 or EF)
CS#
0
1
2
3
4
5
6
7
8
9 10
SCLK
Command
SI
2 Dummy Bytes
15 14 13
90
3
2
1
0
High-Z
SO
CS#
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCLK
ADD (1)
SI
7
6
5
4
3
2
1
0
Manufacturer ID
SO
X
7
6
5
4
3
2
1
Device ID
0
7
6
5
4
3
MSB
MSB
2
1
0
7
MSB
Notes:
(1) ADD=00H will output the manufacturer's ID first and ADD=01H will output device ID first
(2) Instruction is either 90(hex) or EF(hex).
P/N: PM1290
42
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Figure 29. Power-up Timing
VCC
VCC(max)
Chip Selection is Not Allowed
VCC(min)
tVSL
Device is fully accessible
time
Note: VCC (max.) is 3.6V and VCC (min.) is 2.7V.
P/N: PM1290
43
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
RECOMMENDED OPERATING CONDITIONS
At Device Power-Up
AC timing illustrated in Figure A is recommended for the supply voltages and the control signals at device power-up.
If the timing in the figure is ignored, the device may not operate correctly.
VCC
VCC(min)
GND
tSHSL
tVR
CS#
tCHSL
tSLCH
tCHSH
tSHCH
SCLK
tDVCH
tCHCL
tCHDX
tCLCH
LSB IN
MSB IN
SI
High Impedance
SO
Figure A. AC Timing at Device Power-Up
Symbol
Parameter
tVR
VCC Rise Time
Notes
Min.
Max.
Unit
1
20
500000
us/V
Notes :
1.Sampled, not 100% tested.
2.For AC spec tCHSL, tSLCH, tDVCH, tCHDX, tSHSL, tCHSH, tSHCH, tCHCL, tCLCH in the figure, please refer to
"AC CHARACTERISTICS" table.
P/N: PM1290
44
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
ERASE AND PROGRAMMING PERFORMANCE
PARAMETER
TYP. (1)
Max. (2)
UNIT
Write Status Register Cycle Time
40
100
ms
Sector Erase Cycle Time
60
300
ms
Block Erase Cycle Time
0.7
2
s
64Mb
50
80
s
32Mb
25
50
s
16Mb
14
30
s
64Mb
30
48
s
32Mb
15
30
s
16Mb
8
18
s
9
300
us
Page Program Cycle Time
1.4
5
ms
Page Program Cycle Time (at ACC mode)
1.4
5
ms
Chip Erase Cycle Time
Chip Erase Cycle Time (at ACC mode)
Min.
Byte Program Time (via page program command)
Erase/Program Cycle
100,000
cycles
Note:
1. Typical program and erase time assumes the following conditions: 25°C, 3.3V, and checker board pattern.
2. Under worst conditions of 85°C and 2.7V.
3. System-level overhead is the time required to execute the first-bus-cycle sequence for the programming command.
4. Erase/Program cycles comply with JEDEC JESD-47E & A117A standard.
Data Retention
PARAMETER
Condition
Min.
Data retention
55˚C
20
Max.
UNIT
years
LATCH-UP CHARACTERISTICS
MIN.
MAX.
Input Voltage with respect to GND on ACC
-1.0V
10.5V
Input Voltage with respect to GND on all power pins, SI, CS#
-1.0V
2 VCCmax
Input Voltage with respect to GND on SO
-1.0V
VCC + 1.0V
-100mA
+100mA
Current
Includes all pins except VCC. Test conditions: VCC = 3.0V, one pin at a time.
P/N: PM1290
45
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
ORDERING INFORMATION
CLOCK
(MHz)
OPERATING
CURRENT
MAX. (mA)
STANDBY
CURRENT
MAX. (uA)
Temperature
MX25L1605DM2I-12G
86
25
20
-40°C~85°C
MX25L1605DMI-12G
86
25
20
-40°C~85°C
MX25L1605DM1I-12G
86
25
20
-40°C~85°C
MX25L1605DPI-12G
86
25
20
-40°C~85°C
MX25L1605DZNI-12G
86
25
20
-40°C~85°C
MX25L1605DZUI-12G
86
25
20
-40°C~85°C
MX25L3205DZNI-12G
86
25
20
-40°C~85°C
MX25L3205DM2I-12G
86
25
20
-40°C~85°C
MX25L3205DMI-12G
86
25
20
-40°C~85°C
MX25L3205DPI-12G
86
25
20
-40°C~85°C
MX25L3205DZUI-12G
86
25
20
-40°C~85°C
MX25L6405DZNI-12G
86
25
20
-40°C~85°C
MX25L6405DMI-12G
86
25
20
-40°C~85°C
PART NO.
P/N: PM1290
46
PACKAGE
8-SOP
(200mil)
16-SOP
8-SOP
(150mil)
8-PDIP
(300mil)
8-WSON
(6x5mm)
8-USON
(4x4mm)
8-WSON
(6x5mm)
8-SOP
(200mil)
16-SOP
8-PDIP
(300mil)
8-USON
(4x4mm)
8-WSON
(8x6mm)
16-SOP
Remark
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
PART NAME DESCRIPTION
MX 25
L 1605D
ZN
I
12 G
OPTION:
G: Pb-free
SPEED:
12: 86MHz
TEMPERATURE RANGE:
I: Industrial (-40°C to 85°C)
PACKAGE:
ZN: WSON (0.8mm package height)
ZU: USON (0.6mm package height)
M: 300mil 16-SOP
M1: 150mil 8-SOP
M2: 200mil 8-SOP
P: 300mil 8-PDIP
DENSITY & MODE:
1605D: 16Mb
3205D: 32Mb
6405D: 64Mb
TYPE:
L: 3V
DEVICE:
25: Serial Flash
P/N: PM1290
47
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
PACKAGE INFORMATION
P/N: PM1290
48
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
P/N: PM1290
49
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
P/N: PM1290
50
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
P/N: PM1290
51
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
P/N: PM1290
52
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
P/N: PM1290
53
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
P/N: PM1290
54
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
REVISION HISTORY
Revision No. Description
1.0
1. Removed "Preliminary" 1.1
1. Dual I/O Pre-released
1.2
1. Added 8-land USON package information
1.3
1. Modified figure 4 & 5 waveform
2. Revised VHH spec from 11.0V(typ.)~11.5V(max.) to 9.5V(min.)~10.5V(max.)
1.4
1. Revised sector erase time spec from 90ms(typ.) to 60ms(typ.)
2. Removed "Advanced Information" for MX25L3205DZUI-12G
1.5
1. Deleted Low Vcc function
2. Added condition of data retention 20 years 3. Changed typ. tSHSL spec from 100ns to 40ns 4. Changed AC CHARACTERISTICS: Min. tCH and tCL into 5.5/5.5
when fc=86MHz and 13/13 when fR=33MHz
5. Revised copyright page
P/N: PM1290
55
Page
Date
P1
MAR/07/2008
P1,3,21,31 MAY/12/2008
P2,4,46,
JUL/08/2008
47,50
P28
AUG/15/2008
P4,8,30,45
P32,45
P46
P1,6,27
33,43
P1,45
P31
P31
OCT/01/2008
APR/29/2009
P56
REV. 1.5, APR. 29, 2009
MX25L1605D
MX25L3205D
MX25L6405D
Macronix's products are not designed, manufactured, or intended for use for any high risk applications in which
the failure of a single component could cause death, personal injury, severe physical damage, or other substantial harm to persons or property, such as life-support systems, high temperature automotive, medical, aircraft
and military application. Macronix and its suppliers will not be liable to you and/or any third party for any claims,
injuries or damages that may be incurred due to use of Macronix's products in the prohibited applications.
Copyright© Macronix International Co., Ltd. 2006~2009. All Rights Reserved. Macronix, MXIC, MXIC Logo,
MX Logo, are trademarks or registered trademarks of Macronix International Co., Ltd.. The names and brands
of other companies are for identification purposes only and may be claimed as the property of the respective
companies.
MACRONIX INTERNATIONAL CO., LTD.
Macronix Offices : Taiwan
Headquarters, FAB2
Macronix Offices : Japan
Macronix Asia Limited.
Macronix, International Co., Ltd.
16, Li-Hsin Road, Science Park, Hsinchu,
Taiwan, R.O.C.
Tel: +886-3-5786688
Fax: +886-3-5632888
Taipei Office
Macronix, International Co., Ltd.
Macronix Offices : Korea
19F, 4, Min-Chuan E. Road, Sec. 3, Taipei,
Taiwan, R.O.C.
Tel: +886-2-2509-3300
Fax: +886-2-2509-2200
Macronix Offices : China
Macronix (Hong Kong) Co., Limited.
#906, 9F, Kangnam Bldg., 1321-4, Seocho-Dong, Seocho-Ku,
135-070, Seoul, Korea
Tel: +82-02-588-6887
Fax: +82-02-588-6828
Singapore 449408
Tel: +65-6346-5505
Fax: +65-6348-8096
Macronix (Hong Kong) Co., Limited,
SuZhou Office
Macronix Offices : Europe
Macronix Europe N.V.
Koningin Astridlaan 59, Bus 1 1780
No.5, XingHai Rd, SuZhou Industrial Park,
SuZhou China 215021
Tel: +86-512-62580888 Ext: 3300
Fax: +86-512-62586799
Macronix (Hong Kong) Co., Limited,
Shenzhen Office
Macronix Asia Limited.
Macronix Offices : Singapore
Macronix Pte. Ltd.
1 Marine Parade Central, #11-03 Parkway Centre,
702-703, 7/F, Building 9, Hong Kong Science Park,
5 Science Park West Avenue, Sha Tin,
N.T.
Tel: +86-852-2607-4289
Fax: +86-852-2607-4229
NKF Bldg. 5F, 1-2 Higashida-cho,
Kawasaki-ku Kawasaki-shi,
Kanagawa Pref. 210-0005, Japan
Tel: +81-44-246-9100
Fax: +81-44-246-9105
Wemmel Belgium
Tel: +32-2-456-8020
Fax: +32-2-456-8021
Macronix Offices : USA
Room 1401 & 1404, Blcok A, TianAN Hi-Tech PLAZA Tower,
Che Gong Miao, FutianDistrict, Shenzhen PRC 518040
Tel: +86-755-83433579
Fax: +86-755-83438078
Macronix America, Inc.
680 North McCarthy Blvd. Milpitas, CA 95035,
U.S.A.
Tel: +1-408-262-8887
Fax: +1-408-262-8810
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
56