ATxmega16A4/32A4/64A4/128A4 - Complete

Features
• High-performance, Low-power 8/16-bit Atmel® AVR® XMEGA™ Microcontroller
• Non-volatile Program and Data Memories
•
•
•
•
•
– 16 KB - 128 KB of In-System Self-Programmable Flash
– 4 KB - 8 KB Boot Code Section with Independent Lock Bits
– 1 KB - 2 KB EEPROM
– 2 KB - 8 KB Internal SRAM
Peripheral Features
– Four-channel DMA Controller with support for external requests
– Eight-channel Event System
– Five 16-bit Timer/Counters
Three Timer/Counters with 4 Output Compare or Input Capture channels
Two Timer/Counters with 2 Output Compare or Input Capture channels
High-Resolution Extensions on all Timer/Counters
Advanced Waveform Extension on one Timer/Counter
– Five USARTs
IrDA Extension on one USART
– Two Two-Wire Interfaces with dual address match (I2C and SMBus compatible)
– Two SPIs (Serial Peripheral Interfaces) peripherals
– AES and DES Crypto Engine
– 16-bit Real Time Counter with Separate Oscillator
– One Twelve-channel, 12-bit, 2 Msps Analog to Digital Converter
– One Two-channel, 12-bit, 1 Msps Digital to Analog Converter
– Two Analog Comparators with Window compare function
– External Interrupts on all General Purpose I/O pins
– Programmable Watchdog Timer with Separate On-chip Ultra Low Power Oscillator
Special Microcontroller Features
– Power-on Reset and Programmable Brown-out Detection
– Internal and External Clock Options with PLL
– Programmable Multi-level Interrupt Controller
– Sleep Modes: Idle, Power-down, Standby, Power-save, Extended Standby
– Advanced Programming, Test and Debugging Interfaces
PDI (Program and Debug Interface) for programming, test and debugging
I/O and Packages
– 34 Programmable I/O Lines
– 44 - lead TQFP
– 44 - pad VQFN/QFN
– 49 - ball VFBGA
Operating Voltage
– 1.6 – 3.6V
Speed performance
– 0 – 12 MHz @ 1.6 – 3.6V
– 0 – 32 MHz @ 2.7 – 3.6V
8/16-bit
XMEGA A4
Microcontroller
ATxmega128A4
ATxmega64A4
ATxmega32A4
ATxmega16A4
Not recommended for
new designs - Use
XMEGA A4U series
Typical Applications
•
•
•
•
•
Industrial control
Factory automation
Building control
Board control
White Goods
•
•
•
•
•
Climate control
ZigBee
Motor control
Networking
Optical
•
•
•
•
•
Hand-held battery applications
Power tools
HVAC
Metering
Medical Applications
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
1. Ordering Information
Flash
E2
SRAM
Speed (MHz)
Power Supply
ATxmega128A4-AU
128 KB + 8 KB
2 KB
8 KB
32
1.6 - 3.6V
ATxmega64A4-AU
64 KB + 4 KB
2 KB
4 KB
32
1.6 - 3.6V
ATxmega32A4-AU
32 KB + 4 KB
1 KB
4 KB
32
1.6 - 3.6V
ATxmega16A4-AU
16 KB + 4 KB
1 KB
2 KB
32
1.6 - 3.6V
ATxmega128A4-MH
128 KB + 8 KB
2 KB
8 KB
32
1.6 - 3.6V
ATxmega64A4-MH
64 KB + 4 KB
2 KB
4 KB
32
1.6 - 3.6V
ATxmega32A4-MH
32 KB + 4 KB
1 KB
4 KB
32
1.6 - 3.6V
ATxmega16A4-MH
16 KB + 4 KB
1 KB
2 KB
32
1.6 - 3.6V
ATxmega32A4-CU
32 KB + 4K
1 KB
4 KB
32
1.6 - 3.6V
ATxmega16A4-CU
16 KB + 4 KB
1 KB
2 KB
32
1.6 - 3.6V
Ordering Code
Notes:
Package(1)(2)(3)
Temp
44A
-40C - 85C
44M1
49C2
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For packaging information see ”Packaging information” on page 58.
Package Type
44A
44-Lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
44M1
44-Pad, 7x7x1 mm Body, Lead Pitch 0.50 mm, 5.20 mm Exposed Pad, Thermally Enhanced Plastic Very Thin Quad No Lead Package
(VQFN)
49C2
49-Ball (7 x 7 Array), 0.65 mm Pitch, 5.0 x 5.0 x 1.0 mm, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
2
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
2. Pinout/Block Diagram
PA6
2
PA7
3
PB0
4
PB1
5
AVCC
GND
PR1
PR0
RESET/PDI
PDI
39
38
37
36
35
34
PA1
41
PA0
PA2
42
40
PA3
43
Port R
DATA BU S
OSC/CLK
Control
ADC A
BOD
VREF
POR
TEMP
RTC
OCD
AC A0
Power
Control
AC A1
FLASH
CPU
10
EVENT ROUTING NETWORK
Port C
Notes:
Port D
PE2
31
VCC
30
GND
29
PE1
28
PE0
27
PD7
26
PD6
25
PD5
24
PD4
23
PD3
Port E
19
20
21
22
VCC
PD0
PD1
PD2
16
PC6
18
15
PC5
GND
14
PC4
17
13
PC3
PC7
12
11
PC2
PC1
T/C0
PC0
32
DATA BU S
SPI
9
E2PROM
Event System ctrl
USART0:1
VCC
DMA
T/C0:1
8
PE3
Watchdog
SPI
GND
33
RAM
Interrupt Controller
DAC B
TWI
7
T/C0:1
PB3
USART0:1
6
Port B
PB2
Reset
Control
TWI
1
USART0
PA5
A Port A
INDEX CORNER
PA4
Bock Diagram and TQFP/QFN pinout
44
Figure 2-1.
1. For full details on pinout and pin functions refer to ”Pinout and Pin Functions” on page 49.
2. The large center pad underneath the QFN/MLF package should be soldered to ground on the board to ensure good
mechanical stability.
3
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 2-2.
VFBGA pinout
Top view
1
2
3
4
5
Bottom view
6
7
7
6
5
4
3
2
1
A
A
B
B
C
C
D
D
E
E
F
F
G
G
Table 2-1.
VFBGA pinout
1
2
3
4
5
6
A
PA3
AVCC
GND
PR1
PR0
PDI
PE3
B
PA4
PA1
PA0
GND
RESET/PDI
PE2
VCC
C
PA5
PA2
PA6
PA7
GND
PE1
GND
D
PB1
PB2
PB3
PB0
GND
PD7
PE0
E
GND
GND
PC3
GND
PD4
PD5
PD6
F
VCC
PC0
PC4
PC6
PD0
PD1
PD3
G
PC1
PC2
PC5
PC7
GND
VCC
PD2
4
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
3. Overview
The Atmel® AVR® XMEGA™A4 is a family of low power, high performance and peripheral rich
CMOS 8/16-bit microcontrollers based on the AVR enhanced RISC architecture. By executing
powerful instructions in a single clock cycle, the XMEGA A4 achieves throughputs approaching
1 Million Instructions Per Second (MIPS) per MHz allowing the system designer to optimize
power consumption versus processing speed.
The AVR CPU combines a rich instruction set with 32 general purpose working registers. All the
32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent
registers to be accessed in one single instruction, executed in one clock cycle. The resulting
architecture is more code efficient while achieving throughputs many times faster than conventional single-accumulator or CISC based microcontrollers.
The XMEGA A4 devices provide the following features: In-System Programmable Flash with
Read-While-Write capabilities, Internal EEPROM and SRAM, four-channel DMA Controller,
eight-channel Event System, Programmable Multi-level Interrupt Controller, 34 general purpose
I/O lines, 16-bit Real Time Counter (RTC), five flexible 16-bit Timer/Counters with compare
modes and PWM, five USARTs, two Two Wire Serial Interfaces (TWIs), two Serial Peripheral
Interfaces (SPIs), AES and DES crypto engine, one Twelve-channel, 12-bit ADC with optional
differential input with programmable gain, one Two-channel 12-bit DAC, two analog comparators
with window mode, programmable Watchdog Timer with separate Internal Oscillator, accurate
internal oscillators with PLL and prescaler and programmable Brown-Out Detection.
The Program and Debug Interface (PDI), a fast 2-pin interface for programming and debugging,
is available.
The XMEGA A4 devices have five software selectable power saving modes. The Idle mode
stops the CPU while allowing the SRAM, DMA Controller, Event System, Interrupt Controller and
all peripherals to continue functioning. The Power-down mode saves the SRAM and register
contents but stops the oscillators, disabling all other functions until the next TWI or pin-change
interrupt, or Reset. In Power-save mode, the asynchronous Real Time Counter continues to run,
allowing the application to maintain a timer base while the rest of the device is sleeping. In
Standby mode, the Crystal/Resonator Oscillator is kept running while the rest of the device is
sleeping. This allows very fast start-up from external crystal combined with low power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue
to run. To further reduce power consumption, the peripheral clock to each individual peripheral
can optionally be stopped in Active mode and in Idle sleep mode.
The device is manufactured using Atmel's high-density nonvolatile memory technology. The program Flash memory can be reprogrammed in-system through the PDI. A Bootloader running in
the device can use any interface to download the application program to the Flash memory. The
Bootloader software in the Boot Flash section will continue to run while the Application Flash
section is updated, providing true Read-While-Write operation. By combining an 8/16-bit RISC
CPU with In-System Self-Programmable Flash, the Atmel XMEGA A4 is a powerful microcontroller family that provides a highly flexible and cost effective solution for many embedded
applications.
The XMEGA A4 devices are supported with a full suite of program and system development
tools including: C compilers, macro assemblers, program debugger/simulators, programmers,
and evaluation kits.
5
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
3.1
Block Diagram
Figure 3-1.
XMEGA A4 Block Diagram
PR[0..1]
XTAL1/
TOSC1
XTAL2/
TOSC2
Oscillator
Circuits/
Clock
Generation
PORT R (2)
Watchdog
Oscillator
Real Time
Counter
Watchdog
Timer
DATA BUS
PA[0..7]
PORT A (8)
Event System
Controller
Oscillator
Control
VCC
Power
Supervision
POR/BOD &
RESET
GND
SRAM
ACA
DMA
Controller
Sleep
Controller
RESET/
PDI_CLK
PDI
ADCA
PDI_DATA
AREFA
BUS
Controller
Prog/Debug
Controller
VCC/10
Int. Ref.
DES
OCD
Tempref
AREFB
Interrupt
Controller
AES
PORT B (4)
NVM Controller
DACB
TWIE
USARTE0
Flash
IRCOM
EEPROM
TCE0
PORT E (4)
PB[0..3]
CPU
PE[0..3]
DATA BUS
SPID
TCD0:1
USARTD0:1
SPIC
TWIC
TCC0:1
USARTC0:1
EVENT ROUTING NETWORK
PORT C (8)
PORT D (8)
PC[0..7]
PD[0..7]
6
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
4. Resources
A comprehensive set of development tools, application notes and datasheets are available for
download on http://www.atmel.com/avr.
4.1
Recommended reading
• Atmel AVR XMEGA A Manual
• XMEGA A Application Notes
This device data sheet only contains part specific information and a short description of each
peripheral and module. The XMEGA A Manual describes the modules and peripherals in depth.
The XMEGA A application notes contain example code and show applied use of the modules
and peripherals.
The XMEGA A Manual and Application Notes are available from http://www.atmel.com/avr.
5. Disclaimer
For devices that are not available yet, typical values contained in this datasheet are based on
simulations and characterization of other AVR XMEGA microcontrollers manufactured on the
same process technology. Min. and Max values will be available after the device is
characterized.
7
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
6. AVR CPU
6.1
Features
• 8/16-bit high performance AVR RISC Architecture
•
•
•
•
•
•
•
6.2
– 138 instructions
– Hardware multiplier
32x8-bit registers directly connected to the ALU
Stack in RAM
Stack Pointer accessible in I/O memory space
Direct addressing of up to 16M Bytes of program and data memory
True 16/24-bit access to 16/24-bit I/O registers
Support for 8-, 16- and 32-bit Arithmetic
Configuration Change Protection of system critical features
Overview
The XMEGA A4 uses the 8/16-bit AVR CPU. The main function of the CPU is program execution. The CPU must therefore be able to access memories, perform calculations and control
peripherals. Interrupt handling is described in a separate section. Figure 6-1 on page 8 shows
the CPU block diagram.
Figure 6-1.
CPU block diagram
DATA BUS
Flash
Program
Memory
Program
Counter
OCD
Instruction
Register
STATUS/
CONTROL
Instruction
Decode
32 x 8 General
Purpose
Registers
ALU
Multiplier/
DES
DATA BUS
Peripheral
Module 1
Peripheral
Module 2
SRAM
EEPROM
PMIC
The AVR uses a Harvard architecture - with separate memories and buses for program and
data. Instructions in the program memory are executed with a single level pipeline. While one
instruction is being executed, the next instruction is pre-fetched from the program memory. This
8
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
concept enables instructions to be executed in every clock cycle. The program memory is InSystem Re-programmable Flash memory.
6.3
Register File
The fast-access Register File contains 32 x 8-bit general purpose working registers with single
clock cycle access time. This allows single-cycle Arithmetic Logic Unit (ALU) operation. In a typical ALU cycle, the operation is performed on two Register File operands, and the result is stored
back in the Register File.
Six of the 32 registers can be used as three 16-bit address register pointers for data space
addressing - enabling efficient address calculations. One of these address pointers can also be
used as an address pointer for look up tables in Flash program memory.
6.4
ALU - Arithmetic Logic Unit
The high performance Arithmetic Logic Unit (ALU) supports arithmetic and logic operations
between registers or between a constant and a register. Single register operations can also be
executed. Within a single clock cycle, arithmetic operations between general purpose registers
or between a register and an immediate are executed. After an arithmetic or logic operation, the
Status Register is updated to reflect information about the result of the operation.
The ALU operations are divided into three main categories – arithmetic, logical, and bit-functions. Both 8- and 16-bit arithmetic is supported, and the instruction set allows for efficient
implementation of 32-bit arithmetic. The ALU also provides a powerful multiplier supporting both
signed and unsigned multiplication and fractional format.
6.5
Program Flow
When the device is powered on, the CPU starts to execute instructions from the lowest address
in the Flash Program Memory ‘0’. The Program Counter (PC) addresses the next instruction to
be fetched. After a reset, the PC is set to location ‘0’.
Program flow is provided by conditional and unconditional jump and call instructions, capable of
addressing the whole address space directly. Most AVR instructions use a 16-bit word format,
while a limited number uses a 32-bit format.
During interrupts and subroutine calls, the return address PC is stored on the Stack. The Stack
is effectively allocated in the general data SRAM, and consequently the Stack size is only limited
by the total SRAM size and the usage of the SRAM. After reset the Stack Pointer (SP) points to
the highest address in the internal SRAM. The SP is read/write accessible in the I/O memory
space, enabling easy implementation of multiple stacks or stack areas. The data SRAM can
easily be accessed through the five different addressing modes supported in the AVR CPU.
9
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
7. Memories
7.1
Features
• Flash Program Memory
– One linear address space
– In-System Programmable
– Self-Programming and Bootloader support
– Application Section for application code
– Application Table Section for application code or data storage
– Boot Section for application code or bootloader code
– Separate lock bits and protection for all sections
– Built in fast CRC check of a selectable flash program memory section
• Data Memory
– One linear address space
– Single cycle access from CPU
– SRAM
– EEPROM
Byte and page accessible
Optional memory mapping for direct load and store
– I/O Memory
Configuration and Status registers for all peripherals and modules
16 bit-accessible General Purpose Register for global variables or flags
– Bus arbitration
Safe and deterministic handling of CPU and DMA Controller priority
– Separate buses for SRAM, EEPROM, I/O Memory and External Memory access
Simultaneous bus access for CPU and DMA Controller
• Production Signature Row Memory for factory programmed data
Device ID for each microcontroller device type
Serial number for each device
Oscillator calibration bytes
ADC, DAC and temperature sensor calibration data
• User Signature Row
One flash page in size
Can be read and written from software
Content is kept after chip erase
7.2
Overview
The AVR architecture has two main memory spaces, the Program Memory and the Data Memory. In addition, the XMEGA A4 features an EEPROM Memory for non-volatile data storage. All
three memory spaces are linear and require no paging. The available memory size configurations are shown in ”Ordering Information” on page 2. In addition each device has a Flash
memory signature row for calibration data, device identification, serial number etc.
Non-volatile memory spaces can be locked for further write or read/write operations. This prevents unrestricted access to the application software.
10
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
7.3
In-System Programmable Flash Program Memory
The XMEGA A4 devices contain On-chip In-System Programmable Flash memory for program
storage, see Figure 7-1 on page 11. Since all AVR instructions are 16- or 32-bits wide, each
Flash address location is 16 bits.
The Program Flash memory space is divided into Application and Boot sections. Both sections
have dedicated Lock Bits for setting restrictions on write or read/write operations. The Store Program Memory (SPM) instruction must reside in the Boot Section when used to write to the Flash
memory.
A third section inside the Application section is referred to as the Application Table section which
has separate Lock bits for storage of write or read/write protection. The Application Table section can be used for storing non-volatile data or application software.
Figure 7-1.
Flash Program Memory (Hexadecimal address)
Word Address
0
Application Section
(128 KB/64 KB/32 KB/16 KB)
...
EFFF
/
77FF
/
37FF
/
17FF
F000
/
7800
/
3800
/
1800
FFFF
/
7FFF
/
3FFF
/
1FFF
10000
/
8000
/
4000
/
2000
10FFF
/
87FF
/
47FF
/
27FF
Application Table Section
(4 KB/4 KB/4 KB/4 KB)
Boot Section
(8 KB/4 KB/4 KB/4 KB)
The Application Table Section and Boot Section can also be used for general application
software.
11
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
7.4
Data Memory
The Data Memory consist of the I/O Memory, EEPROM and SRAM memories, all within one linear address space, see Figure 7-2 on page 12. To simplify development, the memory map for all
devices in the family is identical and with empty, reserved memory space for smaller devices.
Figure 7-2.
Data Memory Map (Hexadecimal address)
Byte Address
0
FFF
ATxmega64A4
I/O Registers
(4 KB)
1000
EEPROM
(2 KB)
17FF
Byte Address
0
FFF
1000
13FF
RESERVED
2000
2FFF
Internal SRAM
(4 KB)
ATxmega32A4
I/O Registers
(4 KB)
EEPROM
(1 KB)
Byte Address
ATxmega16A4
0
I/O Registers
(4 KB)
FFF
1000
EEPROM
(1 KB)
13FF
RESERVED
2000
2FFF
Internal SRAM
(4 KB)
RESERVED
2000
27FF
Byte Address
0
FFF
Internal SRAM
(2 KB)
ATxmega128A4
I/O Registers
(4 KB)
1000
EEPROM
(2 KB)
17FF
RESERVED
2000
3FFF
7.4.1
Internal SRAM
(8 KB)
I/O Memory
All peripherals and modules are addressable through I/O memory locations in the data memory
space. All I/O memory locations can be accessed by the Load (LD/LDS/LDD) and Store
(ST/STS/STD) instructions, transferring data between the 32 general purpose registers in the
CPU and the I/O Memory.
The IN and OUT instructions can address I/O memory locations in the range 0x00 - 0x3F
directly.
I/O registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and
CBI instructions. The value of single bits can be checked by using the SBIS and SBIC instructions on these registers.
The I/O memory address for all peripherals and modules in XMEGA A4 is shown in the ”Peripheral Module Address Map” on page 53.
7.4.2
SRAM Data Memory
The XMEGA A4 devices have internal SRAM memory for data storage.
12
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
7.4.3
EEPROM Data Memory
The XMEGA A4 devices have internal EEPROM memory for non-volatile data storage. It is
addressable either in a separate data space or it can be memory mapped into the normal data
memory space. The EEPROM memory supports both byte and page access.
7.5
Production Signature Row
The Production Signature Row is a separate memory section for factory programmed data. It
contains calibration data for functions such as oscillators and analog modules.
The production signature row also contains a device ID that identify each microcontroller device
type, and a serial number that is unique for each manufactured device. The device ID for the
available XMEGA A4 devices is shown in Table 7-1 on page 13. The serial number consist of
the production LOT number, wafer number, and wafer coordinates for the device.
The production signature row can not be written or erased, but it can be read from both application software and external programming.
Table 7-1.
Device ID bytes for XMEGA A4 devices.
Device
7.6
Device ID bytes
Byte 2
Byte 1
Byte 0
ATxmega16A4
41
94
1E
ATxmega32A4
41
95
1E
ATxmega64A4
46
96
1E
ATxmega128A4
46
97
1E
User Signature Row
The User Signature Row is a separate memory section that is fully accessible (read and write)
from application software and external programming. The user signature row is one flash page
in size, and is meant for static user parameter storage, such as calibration data, custom serial
numbers or identification numbers, random number seeds etc. This section is not erased by
Chip Erase commands that erase the Flash, and requires a dedicated erase command. This
ensures parameter storage during multiple program/erase session and on-chip debug sessions.
13
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
7.7
Flash and EEPROM Page Size
The Flash Program Memory and EEPROM data memory are organized in pages. The pages are
word accessible for the Flash and byte accessible for the EEPROM.
Table 7-2 on page 14 shows the Flash Program Memory organization. Flash write and erase
operations are performed on one page at a time, while reading the Flash is done one byte at a
time. For Flash access the Z-pointer (Z[m:n]) is used for addressing. The most significant bits in
the address (FPAGE) give the page number and the least significant address bits (FWORD)
give the word in the page.
Table 7-2.
Devices
Number of words and Pages in the Flash.
Flash
Page Size
Size
(words)
FWORD
FPAGE
ATxmega16A4
16 KB + 4 KB
128
Z[6:0]
Z[13:7]
ATxmega32A4
32 KB + 4 KB
128
Z[6:0]
Z[14:7]
ATxmega64A4
64 KB + 4 KB
128
Z[6:0]
ATxmega128A4
128 KB + 8 KB
256
Z[7:0]
Application
Size
Boot
No of Pages
Size
No of Pages
16 KB
64
4 KB
16
32 KB
128
4 KB
16
Z[15:7]
64 KB
128
4 KB
16
Z[16:8]
128 KB
256
8 KB
16
Table 7-3 on page 14 shows EEPROM memory organization for the XMEGA A4 devices.
EEPROM write and erase operations can be performed one page or one byte at a time, while
reading the EEPROM is done one byte at a time. For EEPROM access the NVM Address Register (ADDR[m:n]) is used for addressing. The most significant bits in the address (E2PAGE) give
the page number and the least significant address bits (E2BYTE) give the byte in the page.
Table 7-3.
Devices
Number of Bytes and Pages in the EEPROM.
EEPROM
Page Size
Size
(Bytes)
E2BYTE
E2PAGE
No of Pages
ATxmega16A4
1 KB
ATxmega32A4
1 KB
32
ADDR[4:0]
ADDR[10:5]
32
32
ADDR[4:0]
ADDR[10:5]
32
ATxmega64A4
2 KB
32
ADDR[4:0]
ADDR[10:5]
64
ATxmega128A4
2 KB
32
ADDR[4:0]
ADDR[10:5]
64
14
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
8. DMAC - Direct Memory Access Controller
8.1
Features
• Allows High-speed data transfer
•
•
•
•
•
8.2
– From memory to peripheral
– From memory to memory
– From peripheral to memory
– From peripheral to peripheral
4 Channels
From 1 byte and up to 16 M bytes transfers in a single transaction
Multiple addressing modes for source and destination address
– Increment
– Decrement
– Static
1, 2, 4, or 8 bytes Burst Transfers
Programmable priority between channels
Overview
The XMEGA A4 has a Direct Memory Access (DMA) Controller to move data between memories
and peripherals in the data space. The DMA controller uses the same data bus as the CPU to
transfer data.
It has 4 channels that can be configured independently. Each DMA channel can perform data
transfers in blocks of configurable size from 1 to 64K bytes. A repeat counter can be used to
repeat each block transfer for single transactions up to 16M bytes. Each DMA channel can be
configured to access the source and destination memory address with incrementing, decrementing or static addressing. The addressing is independent for source and destination address.
When the transaction is complete the original source and destination address can automatically
be reloaded to be ready for the next transaction.
The DMAC can access all the peripherals through their I/O memory registers, and the DMA may
be used for automatic transfer of data to/from communication modules, as well as automatic
data retrieval from ADC conversions, data transfer to DAC conversions, or data transfer to or
from port pins. A wide range of transfer triggers is available from the peripherals, Event System
and software. Each DMA channel has different transfer triggers.
To allow for continuous transfer, two channels can be interlinked so that the second takes over
the transfer when the first is finished and vice versa.
The DMA controller can read from memory mapped EEPROM, but it cannot write to the
EEPROM or access the Flash.
15
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
9. Event System
9.1
Features
•
•
•
•
•
•
•
•
9.2
Inter-peripheral communication and signalling with minimum latency
CPU and DMA independent operation
8 Event Channels allow for up to 8 signals to be routed at the same time
Events can be generated by
– TImer/Counters (TCxn)
– Real Time Counter (RTC)
– Analog to Digital Converters (ADCx)
– Analog Comparators (ACx)
– Ports (PORTx)
– System Clock (ClkSYS)
– Software (CPU)
Events can be used by
– TImer/Counters (TCxn)
– Analog to Digital Converters (ADCx)
– Digital to Analog Converters (DACx)
– Ports (PORTx)
– DMA Controller (DMAC)
– IR Communication Module (IRCOM)
The same event can be used by multiple peripherals for synchronized timing
Advanced Features
– Manual Event Generation from software (CPU)
– Quadrature Decoding
– Digital Filtering
Functions in Active and Idle mode
Overview
The Event System is a set of features for inter-peripheral communication. It enables the possibility for a change of state in one peripheral to automatically trigger actions in one or more
peripherals. Whose changes in a peripheral that will trigger actions in other peripherals are configurable by software. It is a simple, but powerful system as it allows for autonomous control of
peripherals without any use of interrupts, CPU or DMA resources.
The indication of a change in a peripheral is referred to as an event, and is usually the same as
the interrupt conditions for that peripheral. Events are passed between peripherals using a dedicated routing network called the Event Routing Network. Figure 9-1 on page 17 shows a basic
block diagram of the Event System with the Event Routing Network and the peripherals to which
it is connected. This highly flexible system can be used for simple routing of signals, pin functions or for sequencing of events.
The maximum latency is two CPU clock cycles from when an event is generated in one peripheral, until the actions are triggered in one or more other peripherals.
The Event System is functional in both Active and Idle modes.
16
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 9-1.
Event System Block Diagram
PORTx
ClkSYS
CPU
ADCx
RTC
Event Routing
Network
DACx
IRCOM
ACx
T/Cxn
DMAC
The Event Routing Network can directly connect together ADCs, DACs, Analog Comparators
(ACx), I/O ports (PORTx), the Real-time Counter (RTC), Timer/Counters (T/C) and the IR Communication Module (IRCOM). Events can also be generated from software (CPU).
All events from all peripherals are always routed into the Event Routing Network. This consist of
eight multiplexers where each can be configured in software to select which event to be routed
into that event channel. All eight event channels are connected to the peripherals that can use
events, and each of these peripherals can be configured to use events from one or more event
channels to automatically trigger a software selectable action.
17
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
10. System Clock and Clock options
10.1
Features
• Fast start-up time
• Safe run-time clock switching
• Internal Oscillators:
•
•
•
•
•
•
10.2
– 32 MHz run-time calibrated RC oscillator
– 2 MHz run-time calibrated RC oscillator
– 32.768 kHz calibrated RC oscillator
– 32 kHz Ultra Low Power (ULP) oscillator with 1 kHz ouput
External clock options
– 0.4 - 16 MHz Crystal Oscillator
– 32 kHz Crystal Oscillator
– External clock
PLL with internal and external clock options with 1 to 31x multiplication
Clock Prescalers with 1 to 2048x division
Fast peripheral clock running at 2 and 4 times the CPU clock speed
Automatic Run-Time Calibration of internal oscillators
Crystal Oscillator failure detection
Overview
XMEGA A4 has an advanced clock system, supporting a large number of clock sources. It incorporates both integrated oscillators, external crystal oscillators and resonators. A high frequency
Phase Locked Loop (PLL) and clock prescalers can be controlled from software to generate a
wide range of clock frequencies from the clock source input.
It is possible to switch between clock sources from software during run-time. After reset the
device will always start up running from the 2 Mhz internal oscillator.
A calibration feature is available, and can be used for automatic run-time calibration of the internal 2 MHz and 32 MHz oscillators. This reduce frequency drift over voltage and temperature.
A Crystal Oscillator Failure Monitor can be enabled to issue a Non-Maskable Interrupt and
switch to internal oscillator if the external oscillator fails. Figure 10-1 on page 19 shows the principal clock system in XMEGA A4.
18
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 10-1. Clock system overview
clkULP
WDT/BOD
32 kHz ULP
Internal Oscillator
clkRTC
RTC
32.768 kHz
Calibrated Internal
Oscillator
PERIPHERALS
ADC
2 MHz
Run-Time Calibrated
Internal Oscillator
32 MHz
Run-time Calibrated
Internal Oscillator
DAC
CLOCK CONTROL
clkPER
UNIT
with PLL and
Prescaler
PORTS
...
DMA
INTERRUPT
32.768 KHz
Crystal Oscillator
EVSYS
RAM
0.4 - 16 MHz
Crystal Oscillator
CPU
clkCPU NVM MEMORY
FLASH
External
Clock Input
EEPROM
Each clock source is briefly described in the following sub-sections.
10.3
10.3.1
Clock Options
32 kHz Ultra Low Power Internal Oscillator
The 32 kHz Ultra Low Power (ULP) Internal Oscillator is a very low power consumption clock
source. It is used for the Watchdog Timer, Brown-Out Detection and as an asynchronous clock
source for the Real Time Counter. This oscillator cannot be used as the system clock source,
and it cannot be directly controlled from software.
10.3.2
32.768 kHz Calibrated Internal Oscillator
The 32.768 kHz Calibrated Internal Oscillator is a high accuracy clock source that can be used
as the system clock source or as an asynchronous clock source for the Real Time Counter. It is
calibrated during production to provide a default frequency which is close to its nominal
frequency.
19
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
10.3.3
32.768 kHz Crystal Oscillator
The 32.768 kHz Crystal Oscillator is a low power driver for an external watch crystal. It can be
used as system clock source or as asynchronous clock source for the Real Time Counter.
10.3.4
0.4 - 16 MHz Crystal Oscillator
The 0.4 - 16 MHz Crystal Oscillator is a driver intended for driving both external resonators and
crystals ranging from 400 kHz to 16 MHz.
10.3.5
2 MHz Run-time Calibrated Internal Oscillator
The 2 MHz Run-time Calibrated Internal Oscillator is a high frequency oscillator. It is calibrated
during production to provide a default frequency which is close to its nominal frequency. The
oscillator can use the 32 kHz Calibrated Internal Oscillator or the 32 kHz Crystal Oscillator as a
source for calibrating the frequency run-time to compensate for temperature and voltage drift
hereby optimizing the accuracy of the oscillator.
10.3.6
32 MHz Run-time Calibrated Internal Oscillator
The 32 MHz Run-time Calibrated Internal Oscillator is a high frequency oscillator. It is calibrated
during production to provide a default frequency which is close to its nominal frequency. The
oscillator can use the 32 kHz Calibrated Internal Oscillator or the 32 kHz Crystal Oscillator as a
source for calibrating the frequency run-time to compensate for temperature and voltage drift
hereby optimizing the accuracy of the oscillator.
10.3.7
External Clock input
The external clock input gives the possibility to connect a clock from an external source.
10.3.8
PLL with Multiplication factor 1 - 31x
The PLL provides the possibility of multiplying a frequency by any number from 1 to 31. In combination with the prescalers, this gives a wide range of output frequencies from all clock sources.
20
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
11. Power Management and Sleep Modes
11.1
Features
• 5 sleep modes
– Idle
– Power-down
– Power-save
– Standby
– Extended standby
• Power Reduction registers to disable clocks to unused peripherals
11.2
Overview
The XMEGA A4 provides various sleep modes tailored to reduce power consumption to a minimum. All sleep modes are available and can be entered from Active mode. In Active mode the
CPU is executing application code. The application code decides when and what sleep mode to
enter. Interrupts from enabled peripherals and all enabled reset sources can restore the microcontroller from sleep to Active mode.
In addition, Power Reduction registers provide a method to stop the clock to individual peripherals from software. When this is done, the current state of the peripheral is frozen and there is no
power consumption from that peripheral. This reduces the power consumption in Active mode
and Idle sleep mode.
11.3
Sleep Modes
11.3.1
Idle Mode
In Idle mode the CPU and Non-Volatile Memory are stopped, but all peripherals including the
Interrupt Controller, Event System and DMA Controller are kept running. Interrupt requests from
all enabled interrupts will wake the device.
11.3.2
Power-down Mode
In Power-down mode all system clock sources, and the asynchronous Real Time Counter (RTC)
clock source, are stopped. This allows operation of asynchronous modules only. The only interrupts that can wake up the MCU are the Two Wire Interface address match interrupts, and
asynchronous port interrupts, e.g pin change.
11.3.3
Power-save Mode
Power-save mode is identical to Power-down, with one exception: If the RTC is enabled, it will
keep running during sleep and the device can also wake up from RTC interrupts.
11.3.4
Standby Mode
Standby mode is identical to Power-down with the exception that all enabled system clock
sources are kept running, while the CPU, Peripheral and RTC clocks are stopped. This reduces
the wake-up time when external crystals or resonators are used.
21
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
11.3.5
Extended Standby Mode
Extended Standby mode is identical to Power-save mode with the exception that all enabled
system clock sources are kept running while the CPU and Peripheral clocks are stopped. This
reduces the wake-up time when external crystals or resonators are used.
22
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
12. System Control and Reset
12.1
Features
• Multiple reset sources for safe operation and device reset
– Power-On Reset
– External Reset
– Watchdog Reset
The Watchdog Timer runs from separate, dedicated oscillator
– Brown-Out Reset
Accurate, programmable Brown-Out levels
– PDI reset
– Software reset
• Asynchronous reset
– No running clock in the device is required for reset
• Reset status register
12.2
Resetting the AVR
During reset, all I/O registers are set to their initial values. The SRAM content is not reset. Application execution starts from the Reset Vector. The instruction placed at the Reset Vector should
be an Absolute Jump (JMP) instruction to the reset handling routine. By default the Reset Vector
address is the lowest Flash program memory address, ‘0’, but it is possible to move the Reset
Vector to the first address in the Boot Section.
The I/O ports of the AVR are immediately tri-stated when a reset source goes active.
The reset functionality is asynchronous, so no running clock is required to reset the device.
After the device is reset, the reset source can be determined by the application by reading the
Reset Status Register.
12.3
12.3.1
Reset Sources
Power-On Reset
The MCU is reset when the supply voltage VCC is below the Power-on Reset threshold voltage.
12.3.2
External Reset
The MCU is reset when a low level is present on the RESET pin.
12.3.3
Watchdog Reset
The MCU is reset when the Watchdog Timer period expires and the Watchdog Reset is enabled.
The Watchdog Timer runs from a dedicated oscillator independent of the System Clock. For
more details see ”WDT - Watchdog Timer” on page 24.
12.3.4
Brown-Out Reset
The MCU is reset when the supply voltage VCC is below the Brown-Out Reset threshold voltage
and the Brown-out Detector is enabled. The Brown-out threshold voltage is programmable.
23
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
12.3.5
PDI reset
The MCU can be reset through the Program and Debug Interface (PDI).
12.3.6
Software reset
The MCU can be reset by the CPU writing to a special I/O register through a timed sequence.
13. WDT - Watchdog Timer
13.1
Features
• 11 selectable timeout periods, from 8 ms to 8s.
• Two operation modes
– Standard mode
– Window mode
• Runs from the 1 kHz output of the 32 kHz Ultra Low Power oscillator
• Configuration lock to prevent unwanted changes
13.2
Overview
The XMEGA A4 has a Watchdog Timer (WDT). The WDT will run continuously when turned on
and if the Watchdog Timer is not reset within a software configurable time-out period, the microcontroller will be reset. The Watchdog Reset (WDR) instruction must be run by software to reset
the WDT, and prevent microcontroller reset.
The WDT has a Window mode. In this mode the WDR instruction must be run within a specified
period called a window. Application software can set the minimum and maximum limits for this
window. If the WDR instruction is not executed inside the window limits, the microcontroller will
be reset.
A protection mechanism using a timed write sequence is implemented in order to prevent
unwanted enabling, disabling or change of WDT settings.
For maximum safety, the WDT also has an Always-on mode. This mode is enabled by programming a fuse. In Always-on mode, application software can not disable the WDT.
24
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
14. PMIC - Programmable Multi-level Interrupt Controller
14.1
Features
• Separate interrupt vector for each interrupt
• Short, predictable interrupt response time
• Programmable Multi-level Interrupt Controller
– 3 programmable interrupt levels
– Selectable priority scheme within low level interrupts (round-robin or fixed)
– Non-Maskable Interrupts (NMI)
• Interrupt vectors can be moved to the start of the Boot Section
14.2
Overview
XMEGA A4 has a Programmable Multi-level Interrupt Controller (PMIC). All peripherals can
define three different priority levels for interrupts; high, medium or low. Medium level interrupts
may interrupt low level interrupt service routines. High level interrupts may interrupt both lowand medium level interrupt service routines. Low level interrupts have an optional round robin
scheme to make sure all interrupts are serviced within a certain amount of time.
The built in oscillator failure detection mechanism can issue a Non-Maskable Interrupt (NMI).
14.3
Interrupt vectors
When an interrupt is serviced, the program counter will jump to the interrupt vector address. The
interrupt vector is the sum of the peripheral’s base interrupt address and the offset address for
specific interrupts in each peripheral. The base addresses for the XMEGA A4 devices are shown
in Table 14-1. Offset addresses for each interrupt available in the peripheral are described for
each peripheral in the XMEGA A manual. For peripherals or modules that have only one interrupt, the interrupt vector is shown in Table 14-1. The program address is the word address.
Table 14-1.
Reset and Interrupt Vectors
Program Address
(Base Address)
Source
0x000
RESET
0x002
OSCF_INT_vect
Crystal Oscillator Failure Interrupt vector (NMI)
0x004
PORTC_INT_base
Port C Interrupt base
0x008
PORTR_INT_base
Port R Interrupt base
0x00C
DMA_INT_base
DMA Controller Interrupt base
0x014
RTC_INT_base
Real Time Counter Interrupt base
0x018
TWIC_INT_base
Two-Wire Interface on Port C Interrupt base
0x01C
TCC0_INT_base
Timer/Counter 0 on port C Interrupt base
0x028
TCC1_INT_base
Timer/Counter 1 on port C Interrupt base
0x030
SPIC_INT_vect
SPI on port C Interrupt vector
0x032
USARTC0_INT_base
USART 0 on port C Interrupt base
0x038
USARTC1_INT_base
USART 1 on port C Interrupt base
0x03E
AES_INT_vect
AES Interrupt vector
Interrupt Description
25
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Table 14-1.
Reset and Interrupt Vectors (Continued)
Program Address
(Base Address)
Source
Interrupt Description
0x040
NVM_INT_base
Non-Volatile Memory Interrupt base
0x044
PORTB_INT_base
Port B Interrupt base
0x056
PORTE_INT_base
Port E Interrupt base
0x05A
TWIE_INT_base
Two-Wire Interface on Port E Interrupt base
0x05E
TCE0_INT_base
Timer/Counter 0 on port E Interrupt base
0x06A
TCE1_INT_base
Timer/Counter 1 on port E Interrupt base
0x074
USARTE0_INT_base
USART 0 on port E Interrupt base
0x080
PORTD_INT_base
Port D Interrupt base
0x084
PORTA_INT_base
Port A Interrupt base
0x088
ACA_INT_base
Analog Comparator on Port A Interrupt base
0x08E
ADCA_INT_base
Analog to Digital Converter on Port A Interrupt base
0x09A
TCD0_INT_base
Timer/Counter 0 on port D Interrupt base
0x0A6
TCD1_INT_base
Timer/Counter 1 on port D Interrupt base
0x0AE
SPID_INT_vector
SPI on port D Interrupt vector
0x0B0
USARTD0_INT_base
USART 0 on port D Interrupt base
0x0B6
USARTD1_INT_base
USART 1 on port D Interrupt base
26
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
15. I/O Ports
15.1
Features
• Selectable input and output configuration for each pin individually
• Flexible pin configuration through dedicated Pin Configuration Register
• Synchronous and/or asynchronous input sensing with port interrupts and events
•
•
•
•
•
•
•
•
•
•
15.2
– Sense both edges
– Sense rising edges
– Sense falling edges
– Sense low level
Asynchronous wake-up from all input sensing configurations
Two port interrupts with flexible pin masking
Highly configurable output driver and pull settings:
–
Totem-pole
–
Pull-up/-down
–
Wired-AND
–
Wired-OR
–
Bus-keeper
–
Inverted I/O
Optional Slew rate control
Configuration of multiple pins in a single operation
Read-Modify-Write (RMW) support
Toggle/clear/set registers for Output and Direction registers
Clock output on port pin
Event Channel 0 output on port pin 7
Mapping of port registers (virtual ports) into bit accessible I/O memory space
Overview
The XMEGA A4 devices have flexible General Purpose I/O Ports. A port consists of up to 8 pins,
ranging from pin 0 to pin 7. The ports implement several functions, including synchronous/asynchronous input sensing, pin change interrupts and configurable output settings. All functions are
individual per pin, but several pins may be configured in a single operation.
15.3
I/O configuration
All port pins (Pn) have programmable output configuration. In addition, all port pins have an
inverted I/O function. For an input, this means inverting the signal between the port pin and the
pin register. For an output, this means inverting the output signal between the port register and
the port pin. The inverted I/O function can be used also when the pin is used for alternate
functions.
27
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
15.3.1
Push-pull
Figure 15-1. I/O configuration - Totem-pole
DIRn
OUTn
Pn
INn
15.3.2
Pull-down
Figure 15-2. I/O configuration - Totem-pole with pull-down (on input)
DIRn
OUTn
Pn
INn
15.3.3
Pull-up
Figure 15-3. I/O configuration - Totem-pole with pull-up (on input)
DIRn
OUTn
Pn
INn
15.3.4
Bus-keeper
The bus-keeper’s weak output produces the same logical level as the last output level. It acts as
a pull-up if the last level was ‘1’, and pull-down if the last level was ‘0’.
28
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 15-4. I/O configuration - Totem-pole with bus-keeper
DIRn
OUTn
Pn
INn
15.3.5
Others
Figure 15-5. Output configuration - Wired-OR with optional pull-down
OUTn
Pn
INn
Figure 15-6. I/O configuration - Wired-AND with optional pull-up
INn
Pn
OUTn
29
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
15.4
Input sensing
•
•
•
•
Sense both edges
Sense rising edges
Sense falling edges
Sense low level
Input sensing is synchronous or asynchronous depending on the enabled clock for the ports,
and the configuration is shown in Figure 15-7 on page 30.
Figure 15-7. Input sensing system overview
Asynchronous sensing
EDGE
DETECT
Interrupt
Control
IREQ
Synchronous sensing
Pn
Synchronizer
INn
Q D
D
INVERTED I/O
R
Q
EDGE
DETECT
Event
R
When a pin is configured with inverted I/O, the pin value is inverted before the input sensing.
15.5
Port Interrupt
Each port has two interrupts with separate priority and interrupt vector. All pins on the port can
be individually selected as source for each of the interrupts. The interrupts are then triggered
according to the input sense configuration for each pin configured as source for the interrupt.
15.6
Alternate Port Functions
In addition to the input/output functions on all port pins, most pins have alternate functions. This
means that other modules or peripherals connected to the port can use the port pins for their
functions, such as communication or pulse-width modulation. ”Pinout and Pin Functions” on
page 49 shows which modules on peripherals that enable alternate functions on a pin, and
which alternate function is available on a pin.
30
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
16. T/C - 16-bit Timer/Counter
16.1
Features
• Five 16-bit Timer/Counters
•
•
•
•
•
•
•
•
•
•
•
•
16.2
– Three Timer/Counters of type 0
– Two Timer/Counters of type 1
Three Compare or Capture (CC) Channels in Timer/Counter 0
Two Compare or Capture (CC) Channels in Timer/Counter 1
Double Buffered Timer Period Setting
Double Buffered Compare or Capture Channels
Waveform Generation:
– Single Slope Pulse Width Modulation
– Dual Slope Pulse Width Modulation
– Frequency Generation
Input Capture:
– Input Capture with Noise Cancelling
– Frequency capture
– Pulse width capture
– 32-bit input capture
Event Counter with Direction Control
Timer Overflow and Timer Error Interrupts and Events
One Compare Match or Capture Interrupt and Event per CC Channel
Supports DMA Operation
Hi-Resolution Extension (Hi-Res)
Advanced Waveform Extension (AWEX)
Overview
XMEGA A4 has five Timer/Counters, three Timer/Counter 0 and two Timer/Counter 1. The difference between them is that Timer/Counter 0 has four Compare/Capture channels, while
Timer/Counter 1 has two Compare/Capture channels.
The Timer/Counters (T/C) are 16-bit and can count any clock, event or external input in the
microcontroller. A programmable prescaler is available to get a useful T/C resolution. Updates of
Timer and Compare registers are double buffered to ensure glitch free operation. Single slope
PWM, dual slope PWM and frequency generation waveforms can be generated using the Compare Channels.
Through the Event System, any input pin or event in the microcontroller can be used to trigger
input capture, hence no dedicated pins are required for this. The input capture has a noise canceller to avoid incorrect capture of the T/C, and can be used to do frequency and pulse width
measurements.
A wide range of interrupt or event sources are available, including T/C Overflow, Compare
match and Capture for each Compare/Capture channel in the T/C.
PORTC and PORTD each has one Timer/Counter 0 and one Timer/Counter1. PORTE has one
Timer/Conter0. Notation of these are TCC0 (Time/Counter C0), TCC1, TCD0, TCD1 and TCE0,
respectively.
31
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 16-1. Overview of a Timer/Counter and closely related peripherals
Timer/Counter
Base Counter
Prescaler
clkPER
Timer Period
Control Logic
Counter
Event
System
clkPER4
Buffer
Capture
Control
Waveform
Generation
DTI
Dead-Time
Insertion
Pattern
Generation
Fault
Protection
PORT
Comparator
AWeX
Hi-Res
Compare/Capture Channel D
Compare/Capture Channel C
Compare/Capture Channel B
Compare/Capture Channel A
The Hi-Resolution Extension can be enabled to increase the waveform generation resolution by
2 bits (4x). This is available for all Timer/Counters. See ”Hi-Res - High Resolution Extension” on
page 34 for more details.
The Advanced Waveform Extension can be enabled to provide extra and more advanced feature for the Timer/Counter. This is only available for Timer/Counter 0. See ”AWEX - Advanced
Waveform Extension” on page 33 for more details.
32
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
17. AWEX - Advanced Waveform Extension
17.1
Features
•
•
•
•
•
•
•
•
17.2
Output with complementary output from each Capture channel
Four Dead Time Insertion (DTI) Units, one for each Capture channel
8-bit DTI Resolution
Separate High and Low Side Dead-Time Setting
Double Buffered Dead-Time
Event Controlled Fault Protection
Single Channel Multiple Output Operation (for BLDC motor control)
Double Buffered Pattern Generation
Overview
The Advanced Waveform Extension (AWEX) provides extra features to the Timer/Counter in
Waveform Generation (WG) modes. The AWEX enables easy and safe implementation of for
example, advanced motor control (AC, BLDC, SR, and Stepper) and power control applications.
Any WG output from a Timer/Counter 0 is split into a complimentary pair of outputs when any
AWEX feature is enabled. These output pairs go through a Dead-Time Insertion (DTI) unit that
enables generation of the non-inverted Low Side (LS) and inverted High Side (HS) of the WG
output with dead time insertion between LS and HS switching. The DTI output will override the
normal port value according to the port override setting. Optionally the final output can be
inverted by using the invert I/O setting for the port pin.
The Pattern Generation unit can be used to generate a synchronized bit pattern on the port it is
connected to. In addition, the waveform generator output from Compare Channel A can be distributed to, and override all port pins. When the Pattern Generator unit is enabled, the DTI unit is
bypassed.
The Fault Protection unit is connected to the Event System. This enables any event to trigger a
fault condition that will disable the AWEX output. Several event channels can be used to trigger
fault on several different conditions.
The AWEX is available for TCC0. The notation of this is AWEXC.
33
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
18. Hi-Res - High Resolution Extension
18.1
Features
• Increases Waveform Generator resolution by 2-bits (4x)
• Supports Frequency, single- and dual-slope PWM operation
• Supports the AWEX when this is enabled and used for the same Timer/Counter
18.2
Overview
The Hi-Resolution (Hi-Res) Extension is able to increase the resolution of the waveform generation output by a factor of 4. When enabled for a Timer/Counter, the Fast Peripheral clock running
at four times the CPU clock speed will be as input to the Timer/Counter.
The High Resolution Extension can also be used when an AWEX is enabled and used with a
Timer/Counter.
XMEGA A4 devices have three Hi-Res Extensions that each can be enabled for each
Timer/Counters pair on PORTC, PORTD and PORTE. The notation of these are HIRESC,
HIRESD and HIRESE, respectively.
34
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
19. RTC - 16-bit Real-Time Counter
19.1
Features
•
•
•
•
•
•
19.2
16-bit Timer
Flexible Tick resolution ranging from 1 Hz to 32.768 kHz
One Compare register
One Period register
Clear timer on Overflow or Compare Match
Overflow or Compare Match event and interrupt generation
Overview
The XMEGA A4 includes a 16-bit Real-time Counter (RTC). The RTC can be clocked from an
accurate 32.768 kHz Crystal Oscillator, the 32.768 kHz Calibrated Internal Oscillator, or from the
32 kHz Ultra Low Power Internal Oscillator. The RTC includes both a Period and a Compare
register. For details, see Figure 19-1.
A wide range of Resolution and Time-out periods can be configured using the RTC. With a maximum resolution of 30.5 µs, time-out periods range up to 2000 seconds. With a resolution of 1
second, the maximum time-out period is over 18 hours (65536 seconds).
Figure 19-1. Real Time Counter overview
Period
Overflow
32 kHz
=
10-bit
prescaler
1 kHz
Counter
=
Compare Match
Compare
35
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
20. TWI - Two-Wire Interface
20.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
20.2
Two Identical TWI peripherals
Simple yet Powerful and Flexible Communication Interface
Both Master and Slave Operation Supported
Device can Operate as Transmitter or Receiver
7-bit Address Space Allows up to 128 Different Slave Addresses
Multi-master Arbitration Support
Up to 400 kHz Data Transfer Speed
Slew-rate Limited Output Drivers
Noise Suppression Circuitry Rejects Spikes on Bus Lines
Fully Programmable Slave Address with General Call Support
Address Recognition Causes Wake-up when in Sleep Mode
I2C and System Management Bus (SMBus) compatible
Overview
The Two-Wire Interface (TWI) is a bi-directional wired-AND bus with only two lines, the clock
(SCL) line and the data (SDA) line. The protocol makes it possible to interconnect up to 128 individually addressable devices. Since it is a multi-master bus, one or more devices capable of
taking control of the bus can be connected.
The only external hardware needed to implement the bus is a single pull-up resistor for each of
the TWI bus lines. Mechanisms for resolving bus contention are inherent in the TWI protocol.
PORTC and PORTE each has one TWI. Notation of these peripherals are TWIC and TWIE,
respectively.
36
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
21. SPI - Serial Peripheral Interface
21.1
Features
•
•
•
•
•
•
•
•
•
21.2
Two Identical SPI peripherals
Full-duplex, Three-wire Synchronous Data Transfer
Master or Slave Operation
LSB First or MSB First Data Transfer
Seven Programmable Bit Rates
End of Transmission Interrupt Flag
Write Collision Flag Protection
Wake-up from Idle Mode
Double Speed (CK/2) Master SPI Mode
Overview
The Serial Peripheral Interface (SPI) allows high-speed full-duplex, synchronous data transfer
between different devices. Devices can communicate using a master-slave scheme, and data is
transferred both to and from the devices simultaneously.
PORTC and PORTD each has one SPI. Notation of these peripherals are SPIC and SPID,
respectively.
37
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
22. USART
22.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
22.2
Five Identical USART peripherals
Full Duplex Operation (Independent Serial Receive and Transmit Registers)
Asynchronous or Synchronous Operation
Master or Slave Clocked Synchronous Operation
High-resolution Arithmetic Baud Rate Generator
Supports Serial Frames with 5, 6, 7, 8, or 9 Data Bits and 1 or 2 Stop Bits
Odd or Even Parity Generation and Parity Check Supported by Hardware
Data OverRun Detection
Framing Error Detection
Noise Filtering Includes False Start Bit Detection and Digital Low Pass Filter
Three Separate Interrupts on TX Complete, TX Data Register Empty and RX Complete
Multi-processor Communication Mode
Double Speed Asynchronous Communication Mode
Master SPI mode for SPI communication
IrDA support through the IRCOM module
Overview
The Universal Synchronous and Asynchronous serial Receiver and Transmitter (USART) is a
highly flexible serial communication module. The USART supports full duplex communication,
and both asynchronous and clocked synchronous operation. The USART can also be set in
Master SPI mode to be used for SPI communication.
Communication is frame based, and the frame format can be customized to support a wide
range of standards. The USART is buffered in both direction, enabling continued data transmission without any delay between frames. There are separate interrupt vectors for receive and
transmit complete, enabling fully interrupt driven communication. Frame error and buffer overflow are detected in hardware and indicated with separate status flags. Even or odd parity
generation and parity check can also be enabled.
One USART can use the IRCOM module to support IrDA 1.4 physical compliant pulse modulation and demodulation for baud rates up to 115.2 kbps.
PORTC and PORTD each has two USARTs. PORTE has one USART. Notation of these peripherals are USARTC0, USARTC1, USARTD0, USARTD1 and USARTE0, respectively.
38
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
23. IRCOM - IR Communication Module
23.1
Features
• Pulse modulation/demodulation for infrared communication
• Compatible to IrDA 1.4 physical for baud rates up to 115.2 kbps
• Selectable pulse modulation scheme
– 3/16 of baud rate period
– Fixed pulse period, 8-bit programmable
– Pulse modulation disabled
• Built in filtering
• Can be connected to and used by one USART at a time
23.2
Overview
XMEGA contains an Infrared Communication Module (IRCOM) for IrDA communication with
baud rates up to 115.2 kbps. This supports three modulation schemes: 3/16 of baud rate period,
fixed programmable pulse time based on the Peripheral Clock speed, or pulse modulation disabled. There is one IRCOM available which can be connected to any USART to enable infrared
pulse coding/decoding for that USART.
39
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
24. Crypto Engine
24.1
Features
• Data Encryption Standard (DES) CPU instruction
• Advanced Encryption Standard (AES) Crypto module
• DES Instruction
– Encryption and Decryption
– Single-cycle DES instruction
– Encryption/Decryption in 16 clock cycles per 8-byte block
• AES Crypto Module
– Encryption and Decryption
– Support 128-bit keys
– Support XOR data load mode to the State memory for Cipher Block Chaining
– Encryption/Decryption in 375 clock cycles per 16-byte block
24.2
Overview
The Advanced Encryption Standard (AES) and Data Encryption Standard (DES) are two commonly used encryption standards. These are supported through an AES peripheral module and
a DES CPU instruction. All communication interfaces and the CPU can optionally use AES and
DES encrypted communication and data storage.
DES is supported by a DES instruction in the AVR XMEGA CPU. The 8-byte key and 8-byte
data blocks must be loaded into the Register file, and then DES must be executed 16 times to
encrypt/decrypt the data block.
The AES Crypto Module encrypts and decrypts 128-bit data blocks with the use of a 128-bit key.
The key and data must be loaded into the key and state memory in the module before encryption/decryption is started. It takes 375 peripheral clock cycles before the encryption/decryption is
done and decrypted/encrypted data can be read out, and an optional interrupt can be generated.
The AES Crypto Module also has DMA support with transfer triggers when encryption/decryption is done and optional auto-start of encryption/decryption when the state memory is fully
loaded.
40
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
25. ADC - 12-bit Analog to Digital Converter
25.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
25.2
One ADC with 12-bit resolution
2 Msps sample rate
Signed and Unsigned conversions
4 result registers with individual input channel control
12 single ended inputs
8x4 differential inputs
4 internal inputs:
–
Integrated Temperature Sensor
–
DAC Output
–
VCC voltage divided by 10
–
Bandgap voltage
Software selectable gain of 2, 4, 8, 16, 32 or 64
Selectable accuracy of 8- or 12-bit.
Internal or External Reference selection
Event triggered conversion for accurate timing
DMA transfer of conversion results
Interrupt/Event on compare result
Overview
XMEGA A4 devices have one Analog to Digital Converter (ADC), see Figure 25-1 on page 42.
The ADC converts analog voltages to digital values. The ADC has 12-bit resolution and is capable of converting up to 2 million samples per second. The input selection is flexible, and both
single-ended and differential measurements can be done. For differential measurements an
optional gain stage is available to increase the dynamic range. In addition several internal signal
inputs are available. The ADC can provide both signed and unsigned results.
This is a pipeline ADC. A pipeline ADC consists of several consecutive stages, where each
stage convert one part of the result. The pipeline design enables high sample rate at low clock
speeds, and remove limitations on samples speed versus propagation delay. This also means
that a new analog voltage can be sampled and a new ADC measurement started while other
ADC measurements are ongoing.
ADC measurements can either be started by application software or an incoming event from
another peripheral in the device. Four different result registers with individual input selection
(MUX selection) are provided to make it easier for the application to keep track of the data. Each
result register and MUX selection pair is referred to as an ADC Channel. It is possible to use
DMA to move ADC results directly to memory or peripherals when conversions are done.
Both internal and external analog reference voltages can be used. An accurate internal 1.0V
reference is available.
An integrated temperature sensor is available and the output from this can be measured with the
ADC. The output from the DAC, VCC/10 and the Bandgap voltage can also be measured by the
ADC.
41
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 25-1. ADC overview
Channel A MUX selection
Channel C MUX selection
Channel D MUX selection
Configuration
Reference selection
Pin inputs
Channel A
Register
Channel B
Register
Pin inputs
Internal inputs
Channel B MUX selection
ADC
Channel C
Register
1-64 X
Event
Trigger
Channel D
Register
Each ADC has four MUX selection registers with a corresponding result register. This means
that four channels can be sampled within 1.5 µs without any intervention by the application other
than starting the conversion. The results will be available in the result registers.
The ADC may be configured for 8- or 12-bit resolution, reducing the minimum conversion time
(propagation delay) from 3.5 µs for 12-bit to 2.5 µs for 8-bit resolution.
ADC conversion results are provided left- or right adjusted with optional ‘1’ or ‘0’ padding. This
eases calculation when the result is represented as a signed integer (signed 16-bit number).
PORTA has one ADC. Notation of this peripheral is ADCA.
42
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
26. DAC - 12-bit Digital to Analog Converter
26.1
Features
•
•
•
•
•
•
•
•
26.2
One DAC with 12-bit resolution
Up to 1 Msps conversion rate
Flexible conversion range
Multiple trigger sources
1 continuous output or 2 Sample and Hold (S/H) outputs
Built-in offset and gain calibration
High drive capabilities
Low Power Mode
Overview
The XMEGA A4 devices feature one 12-bit, 1 Msps DAC with built-in offset and gain calibration,
see Figure 26-1 on page 43.
A DAC converts a digital value into an analog signal. The DAC may use an internal 1.0 voltage
as the upper limit for conversion, but it is also possible to use the supply voltage or any applied
voltage in-between. The external reference input is shared with the ADC reference input.
Figure 26-1. DAC overview
Configuration
Reference selection
Channel A
Register
Channel A
DAC
Channel B
Channel B
Register
Event
Trigger
The DAC has one continuous output with high drive capabilities for both resistive and capacitive
loads. It is also possible to split the continuous time channel into two Sample and Hold (S/H)
channels, each with separate data conversion registers.
A DAC conversion may be started from the application software by writing the data conversion
registers. The DAC can also be configured to do conversions triggered by the Event System to
have regular timing, independent of the application software. DMA may be used for transferring
data from memory locations to DAC data registers.
The DAC has a built-in calibration system to reduce offset and gain error when loading with a
calibration value from software.
PORTB has one DAC. Notation of this peripheral is DACB.
43
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
27. AC - Analog Comparator
27.1
Features
• Two Analog Comparators
• Selectable Power vs. Speed
• Selectable hysteresis
– 0, 20 mV, 50 mV
• Analog Comparator output available on pin
• Flexible Input Selection
– All pins on the port
– Output from the DAC
– Bandgap reference voltage.
– Voltage scaler that can perform a 64-level scaling of the internal VCC voltage.
• Interrupt and event generation on
– Rising edge
– Falling edge
– Toggle
• Window function interrupt and event generation on
– Signal above window
– Signal inside window
– Signal below window
27.2
Overview
XMEGA A4 features two Analog Comparators (AC). An Analog Comparator compares two voltages, and the output indicates which input is largest. The Analog Comparator may be configured
to give interrupt requests and/or events upon several different combinations of input change.
Both hysteresis and propagation delays may be adjusted in order to find the optimal operation
for each application.
A wide range of input selection is available, both external pins and several internal signals can
be used.
The Analog Comparators are always grouped in pairs (AC0 and AC1) on each analog port. They
have identical behavior but separate control registers.
Optionally, the state of the comparator is directly available on a pin.
PORTA has one AC pair. Notation of this peripheral is ACA.
44
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 27-1. Analog comparator overview
Pin inputs
Internal inputs
+
Pin 0 output
AC0
Pin inputs
-
Internal inputs
VCC scaled
Interrupt
sensitivity
control
Pin inputs
Interrupts
Events
Internal inputs
+
AC1
Pin inputs
-
Internal inputs
VCC scaled
45
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
27.3
Input Selection
The Analog comparators have a very flexible input selection and the two comparators grouped
in a pair may be used to realize a window function. One pair of analog comparators is shown in
Figure 27-1 on page 45.
• Input selection from pin
– Pin 0, 1, 2, 3, 4, 5, 6 selectable to positive input of analog comparator
– Pin 0, 1, 3, 5, 7 selectable to negative input of analog comparator
• Internal signals available on positive analog comparator inputs
– Output from 12-bit DAC
• Internal signals available on negative analog comparator inputs
– 64-level scaler of the VCC, available on negative analog comparator input
– Bandgap voltage reference
– Output from 12-bit DAC
27.4
Window Function
The window function is realized by connecting the external inputs of the two analog comparators
in a pair as shown in Figure 27-2.
Figure 27-2. Analog comparator window function
+
AC0
Upper limit of window
Interrupt
sensitivity
control
Input signal
Interrupts
Events
+
AC1
Lower limit of window
-
46
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
28. OCD - On-chip Debug
28.1
Features
• Complete Program Flow Control
– Go, Stop, Reset, Step into, Step over, Step out, Run-to-Cursor
Debugging on C and high-level language source code level
Debugging on Assembler and disassembler level
1 dedicated program address or source level breakpoint for AVR Studio / debugger
4 Hardware Breakpoints
Unlimited Number of User Program Breakpoints
Unlimited Number of User Data Breakpoints, with break on:
– Data location read, write or both read and write
– Data location content equal or not equal to a value
– Data location content is greater or less than a value
– Data location content is within or outside a range
– Bits of a data location are equal or not equal to a value
• Non-Intrusive Operation
– No hardware or software resources in the device are used
• High Speed Operation
– No limitation on debug/programming clock frequency versus system clock frequency
•
•
•
•
•
•
28.2
Overview
The XMEGA A4 has a powerful On-Chip Debug (OCD) system that - in combination with Atmel’s
development tools - provides all the necessary functions to debug an application. It has support
for program and data breakpoints, and can debug an application from C and high level language
source code level, as well as assembler and disassembler level. It has full Non-Intrusive Operation and no hardware or software resources in the device are used. The ODC system is
accessed through an external debugging tool which connects to the PDI physical interface.
Refer to ”Program and Debug Interfaces” on page 48.
47
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
29. Program and Debug Interfaces
29.1
Features
• PDI - Program and Debug Interface (Atmel proprietary 2-pin interface)
• Access to the OCD system
• Programming of Flash, EEPROM, Fuses and Lock Bits
29.2
Overview
The programming and debug facilities are accessed through PDI physical interface. The PDI
physical interface uses one dedicated pin together with the Reset pin, and no general purpose
pins are used.
29.3
PDI - Program and Debug Interface
The PDI is an Atmel proprietary protocol for communication between the microcontroller and
Atmel’s development tools.
48
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
30. Pinout and Pin Functions
The pinout of XMEGA A4 is shown in ”Pinout/Block Diagram” on page 3. In addition to general
I/O functionality, each pin may have several functions. This will depend on which peripheral is
enabled and connected to the actual pin. Only one of the alternate pin functions can be used at
time.
30.1
Alternate Pin Functions Description
The tables below shows the notation for all pin functions available and describe their functions.
30.1.1
30.1.2
30.1.3
30.1.4
Operation/Power Supply
VCC
Digital supply voltage
AVCC
Analog supply voltage
GND
Ground
Port Interrupt functions
SYNC
Port pin with full synchronous and limited asynchronous interrupt function
ASYNC
Port pin with full synchronous and full asynchronous interrupt function
Analog functions
ACn
Analog Comparator input pin n
AC0OUT
Analog Comparator 0 Output
ADCn
Analog to Digital Converter input pin n
DACn
Digital to Analog Converter output pin n
AREF
Analog Reference input pin
Timer/Counter and AWEX functions
OCnx
Output Compare Channel x for Timer/Counter n
OCnx
Inverted Output Compare Channel x for Timer/Counter n
OCnxLS
Output Compare Channel x Low Side for Timer/Counter n
OCnxHS
Output Compare Channel x High Side for Timer/Counter n
49
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
30.1.5
30.1.6
30.1.7
Communication functions
SCL
Serial Clock for TWI
SDA
Serial Data for TWI
XCKn
Transfer Clock for USART n
RXDn
Receiver Data for USART n
TXDn
Transmitter Data for USART n
SS
Slave Select for SPI
MOSI
Master Out Slave In for SPI
MISO
Master In Slave Out for SPI
SCK
Serial Clock for SPI
Oscillators, Clock and Event
TOSCn
Timer Oscillator pin n
XTALn
Input/Output for inverting Oscillator pin n
Debug/System functions
RESET
Reset pin
PDI_CLK
Program and Debug Interface Clock pin
PDI_DATA
Program and Debug Interface Data pin
50
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
30.2
Alternate Pin Functions
The tables below shows the main and alternate pin functions for all pins on each port. It also
shows which peripheral which make use of or enable the alternate pin function.
Table 30-1.
PORTA
Port A - Alternate functions
PIN #
INTERRUPT
ADCA POS
ADCA NEG
ADCA
GAINPOS
ADCA
GAINNEG
ACA POS
ACA NEG
GND
38
AVCC
39
PA0
40
SYNC
ADC0
ADC0
ADC0
AC0
AC0
PA1
41
SYNC
ADC1
ADC1
ADC1
AC1
AC1
PA2
42
SYNC/ASYNC
ADC2
ADC2
ADC2
AC2
PA3
43
SYNC
ADC3
ADC3
ADC3
AC3
PA4
44
SYNC
ADC4
ADC4
ADC4
PA5
1
SYNC
ADC5
ADC5
ADC5
AC5
PA6
2
SYNC
ADC6
ADC6
ADC6
AC6
PA7
3
SYNC
ADC7
ADC7
ADC7
Table 30-2.
PORTB
INTERRUPT
ADCA POS
PB0
4
SYNC
ADC8
PB1
5
SYNC
ADC9
PB2
6
SYNC/ASYNC
ADC10
DAC0
PB3
7
SYNC
ADC11
DAC1
PORTC
REF
AREF
AC3
AC4
AC5
AC7
AC0 OUT
Port B - Alternate functions
PIN #
Table 30-3.
ACA OUT
DACB
REF
AREF
Port C - Alternate functions
PIN #
INTERRUPT
TCC0
AWEXC
TCC1
USARTC0
USARTC1
SPI
GND
8
VCC
9
PC0
10
SYNC
OC0A
OC0ALS
PC1
11
SYNC
OC0B
OC0AHS
XCK0
PC2
12
SYNC/ASYNC
OC0C
OC0BLS
RXD0
PC3
13
SYNC
OC0D
OC0BHS
PC4
14
SYNC
OC0CLS
OC1A
PC5
15
SYNC
OC0CHS
OC1B
XCK1
MOSI
PC6
16
SYNC
OC0DLS
RXD1
MISO
PC7
17
SYNC
OC0DHS
TXD1
SCK
TWIC
CLOCKOUT
EVENTOUT
CLKOUT
EVOUT
SDA
SCL
TXD0
SS
51
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Table 30-4.
PORTD
Port D - Alternate functions
PIN #
INTERRUPT
TCD0
SYNC
OC0A
TCD1
USARTD0
USARTD1
SPID
GND
18
VCC
19
PD0
20
PD1
21
SYNC
OC0B
XCK0
PD2
22
SYNC/ASYNC
OC0C
RXD0
PD3
23
SYNC
OC0D
TXD0
PD4
24
SYNC
OC1A
PD5
25
SYNC
OC1B
XCK1
MOSI
PD6
26
SYNC
RXD1
MISO
PD7
27
SYNC
TXD1
SCK
Table 30-5.
PORT E
CLKOUT
EVOUT
Port E - Alternate functions
PIN #
INTERRUPT
TCE0
28
SYNC
OC0A
PE1
29
SYNC
OC0B
XCK0
GND
30
VCC
31
PE2
32
SYNC/ASYNC
OC0C
RXD0
PE3
33
SYNC
OC0D
TXD0
PORTR
EVENTOUT
SS
PE0
Table 30-6.
CLOCKOUT
USARTE0
TWIE
SDA
SCL
Port R - Alternate functions
PIN #
XTAL
PDI
TOSC
PDI
34
PDI_DATA
RESET
35
PDI_CLK
PR0
36
XTAL2
TOSC2
PR1
37
XTAL1
TOSC1
52
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
31. Peripheral Module Address Map
The address maps show the base address for each peripheral and module in XMEGA A4. For
complete register description and summary for each peripheral module, refer to the XMEGA A
Manual.
Base Address
0x0000
0x0010
0x0014
0x0018
0x001C
0x0030
0x0040
0x0048
0x0050
0x0060
0x0068
0x0070
0x0078
0x0080
0x0090
0x00A0
0x00B0
0x00C0
0x0100
0x0180
0x01C0
0x0200
0x0320
0x0380
0x0400
0x0480
0x04A0
0x0600
0x0620
0x0640
0x0660
0x0680
0x07E0
0x0800
0x0840
0x0880
0x0890
0x08A0
0x08B0
0x08C0
0x08F8
0x0900
0x0940
0x0990
0x09A0
0x09B0
0x09C0
0x0A00
0x0A90
0x0AA0
Name
Description
GPIO
VPORT0
VPORT1
VPORT2
VPORT3
CPU
CLK
SLEEP
OSC
DFLLRC32M
DFLLRC2M
PR
RST
WDT
MCU
PMIC
PORTCFG
AES
DMA
EVSYS
NVM
ADCA
DACB
ACA
RTC
TWIC
TWIE
PORTA
PORTB
PORTC
PORTD
PORTE
PORTR
TCC0
TCC1
AWEXC
HIRESC
USARTC0
USARTC1
SPIC
IRCOM
TCD0
TCD1
HIRESD
USARTD0
USARTD1
SPID
TCE0
HIRESE
USARTE0
General Purpose IO Registers
Virtual Port 0
Virtual Port 1
Virtual Port 2
Virtual Port 2
CPU
Clock Control
Sleep Controller
Oscillator Control
DFLL for the 32 MHz Internal RC Oscillator
DFLL for the 2 MHz RC Oscillator
Power Reduction
Reset Controller
Watch-Dog Timer
MCU Control
Programmable MUltilevel Interrupt Controller
Port Configuration
AES Module
DMA Controller
Event System
Non Volatile Memory (NVM) Controller
Analog to Digital Converter on port A
Digital to Analog Converter on port B
Analog Comparator pair on port A
Real Time Counter
Two Wire Interface on port C
Two Wire Interface on port E
Port A
Port B
Port C
Port D
Port E
Port R
Timer/Counter 0 on port C
Timer/Counter 1 on port C
Advanced Waveform Extension on port C
High Resolution Extension on port C
USART 0 on port C
USART 1 on port C
Serial Peripheral Interface on port C
Infrared Communication Module
Timer/Counter 0 on port D
Timer/Counter 1 on port D
High Resolution Extension on port D
USART 0 on port D
USART 1 on port D
Serial Peripheral Interface on port D
Timer/Counter 0 on port E
High Resolution Extension on port E
USART 0 on port E
53
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
32. Instruction Set Summary
Mnemonics
Operands
Description
Operation
Flags
#Clocks
Arithmetic and Logic Instructions
Rd, Rr
Add without Carry
Rd

Rd + Rr
Z,C,N,V,S,H
1
ADC
Rd, Rr
Add with Carry
Rd

Rd + Rr + C
Z,C,N,V,S,H
1
ADIW
Rd, K
Add Immediate to Word
Rd

Rd + 1:Rd + K
Z,C,N,V,S
2
SUB
Rd, Rr
Subtract without Carry
Rd

Rd - Rr
Z,C,N,V,S,H
1
SUBI
Rd, K
Subtract Immediate
Rd

Rd - K
Z,C,N,V,S,H
1
SBC
Rd, Rr
Subtract with Carry
Rd

Rd - Rr - C
Z,C,N,V,S,H
1
SBCI
Rd, K
Subtract Immediate with Carry
Rd

Rd - K - C
Z,C,N,V,S,H
1
SBIW
Rd, K
Subtract Immediate from Word
Rd + 1:Rd

Rd + 1:Rd - K
Z,C,N,V,S
2
ADD
AND
Rd, Rr
Logical AND
Rd

Rd  Rr
Z,N,V,S
1
ANDI
Rd, K
Logical AND with Immediate
Rd

Rd  K
Z,N,V,S
1
OR
Rd, Rr
Logical OR
Rd

Rd v Rr
Z,N,V,S
1
ORI
Rd, K
Logical OR with Immediate
Rd

Rd v K
Z,N,V,S
1
EOR
Rd, Rr
Exclusive OR
Rd

Rd  Rr
Z,N,V,S
1
COM
Rd
One’s Complement
Rd

$FF - Rd
Z,C,N,V,S
1
NEG
Rd
Two’s Complement
Rd

$00 - Rd
Z,C,N,V,S,H
1
SBR
Rd,K
Set Bit(s) in Register
Rd

Rd v K
Z,N,V,S
1
CBR
Rd,K
Clear Bit(s) in Register
Rd

Rd  ($FFh - K)
Z,N,V,S
1
INC
Rd
Increment
Rd

Rd + 1
Z,N,V,S
1
DEC
Rd
Decrement
Rd

Rd - 1
Z,N,V,S
1
TST
Rd
Test for Zero or Minus
Rd

Rd  Rd
Z,N,V,S
1
CLR
Rd
Clear Register
Rd

Rd  Rd
Z,N,V,S
1
SER
Rd
Set Register
Rd

$FF
None
1
MUL
Rd,Rr
Multiply Unsigned
R1:R0

Rd x Rr (UU)
Z,C
2
MULS
Rd,Rr
Multiply Signed
R1:R0

Rd x Rr (SS)
Z,C
2
MULSU
Rd,Rr
Multiply Signed with Unsigned
R1:R0

Rd x Rr (SU)
Z,C
2
FMUL
Rd,Rr
Fractional Multiply Unsigned
R1:R0

Rd x Rr<<1 (UU)
Z,C
2
FMULS
Rd,Rr
Fractional Multiply Signed
R1:R0

Rd x Rr<<1 (SS)
Z,C
2
FMULSU
Rd,Rr
Fractional Multiply Signed with Unsigned
R1:R0

Rd x Rr<<1 (SU)
Z,C
2
DES
K
Data Encryption
if (H = 0) then R15:R0
else if (H = 1) then R15:R0


Encrypt(R15:R0, K)
Decrypt(R15:R0, K)
PC

PC + k + 1
None
2
1/2
Branch Instructions
RJMP
k
Relative Jump
IJMP
Indirect Jump to (Z)
PC(15:0)
PC(21:16)


Z,
0
None
2
EIJMP
Extended Indirect Jump to (Z)
PC(15:0)
PC(21:16)


Z,
EIND
None
2
JMP
k
Jump
PC

k
None
3
RCALL
k
Relative Call Subroutine
PC

PC + k + 1
None
2 / 3(1)
ICALL
Indirect Call to (Z)
PC(15:0)
PC(21:16)


Z,
0
None
2 / 3(1)
EICALL
Extended Indirect Call to (Z)
PC(15:0)
PC(21:16)


Z,
EIND
None
3(1)
54
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Mnemonics
Operands
Description
CALL
k
call Subroutine
PC

RET
Subroutine Return
PC
RETI
Interrupt Return
CPSE
Rd,Rr
Compare, Skip if Equal
CP
Rd,Rr
Compare
CPC
Rd,Rr
Compare with Carry
CPI
Rd,K
Compare with Immediate
Operation
Flags
#Clocks
k
None
3 / 4(1)

STACK
None
4 / 5(1)
PC

STACK
I
4 / 5(1)
if (Rd = Rr) PC

PC + 2 or 3
None
1/2/3
Rd - Rr
Z,C,N,V,S,H
1
Rd - Rr - C
Z,C,N,V,S,H
1
Rd - K
Z,C,N,V,S,H
1
SBRC
Rr, b
Skip if Bit in Register Cleared
if (Rr(b) = 0) PC

PC + 2 or 3
None
1/2/3
SBRS
Rr, b
Skip if Bit in Register Set
if (Rr(b) = 1) PC

PC + 2 or 3
None
1/2/3
SBIC
A, b
Skip if Bit in I/O Register Cleared
if (I/O(A,b) = 0) PC

PC + 2 or 3
None
2/3/4
SBIS
A, b
Skip if Bit in I/O Register Set
If (I/O(A,b) =1) PC

PC + 2 or 3
None
2/3/4
BRBS
s, k
Branch if Status Flag Set
if (SREG(s) = 1) then PC

PC + k + 1
None
1/2
BRBC
s, k
Branch if Status Flag Cleared
if (SREG(s) = 0) then PC

PC + k + 1
None
1/2
BREQ
k
Branch if Equal
if (Z = 1) then PC

PC + k + 1
None
1/2
BRNE
k
Branch if Not Equal
if (Z = 0) then PC

PC + k + 1
None
1/2
BRCS
k
Branch if Carry Set
if (C = 1) then PC

PC + k + 1
None
1/2
BRCC
k
Branch if Carry Cleared
if (C = 0) then PC

PC + k + 1
None
1/2
BRSH
k
Branch if Same or Higher
if (C = 0) then PC

PC + k + 1
None
1/2
BRLO
k
Branch if Lower
if (C = 1) then PC

PC + k + 1
None
1/2
BRMI
k
Branch if Minus
if (N = 1) then PC

PC + k + 1
None
1/2
BRPL
k
Branch if Plus
if (N = 0) then PC

PC + k + 1
None
1/2
BRGE
k
Branch if Greater or Equal, Signed
if (N  V= 0) then PC

PC + k + 1
None
1/2
BRLT
k
Branch if Less Than, Signed
if (N  V= 1) then PC

PC + k + 1
None
1/2
BRHS
k
Branch if Half Carry Flag Set
if (H = 1) then PC

PC + k + 1
None
1/2
BRHC
k
Branch if Half Carry Flag Cleared
if (H = 0) then PC

PC + k + 1
None
1/2
BRTS
k
Branch if T Flag Set
if (T = 1) then PC

PC + k + 1
None
1/2
BRTC
k
Branch if T Flag Cleared
if (T = 0) then PC

PC + k + 1
None
1/2
BRVS
k
Branch if Overflow Flag is Set
if (V = 1) then PC

PC + k + 1
None
1/2
BRVC
k
Branch if Overflow Flag is Cleared
if (V = 0) then PC

PC + k + 1
None
1/2
BRIE
k
Branch if Interrupt Enabled
if (I = 1) then PC

PC + k + 1
None
1/2
BRID
k
Branch if Interrupt Disabled
if (I = 0) then PC

PC + k + 1
None
1/2
MOV
Rd, Rr
Copy Register
Rd

Rr
None
1
MOVW
Rd, Rr
Copy Register Pair
Rd+1:Rd

Rr+1:Rr
None
1
LDI
Rd, K
Load Immediate
Rd

K
None
1
LDS
Rd, k
Load Direct from data space
Rd

(k)
None
2(1)(2)
LD
Rd, X
Load Indirect
Rd

(X)
None
1(1)(2)
LD
Rd, X+
Load Indirect and Post-Increment
Rd
X


(X)
X+1
None
1(1)(2)
LD
Rd, -X
Load Indirect and Pre-Decrement
X  X - 1,
Rd  (X)


X-1
(X)
None
2(1)(2)
LD
Rd, Y
Load Indirect
Rd  (Y)

(Y)
None
1(1)(2)
LD
Rd, Y+
Load Indirect and Post-Increment
Rd
Y


(Y)
Y+1
None
1(1)(2)
Data Transfer Instructions
55
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Mnemonics
Operands
Description
Flags
#Clocks
LD
Rd, -Y
Load Indirect and Pre-Decrement
Y
Rd


Y-1
(Y)
None
2(1)(2)
LDD
Rd, Y+q
Load Indirect with Displacement
Rd

(Y + q)
None
2(1)(2)
LD
Rd, Z
Load Indirect
Rd

(Z)
None
1(1)(2)
LD
Rd, Z+
Load Indirect and Post-Increment
Rd
Z


(Z),
Z+1
None
1(1)(2)
LD
Rd, -Z
Load Indirect and Pre-Decrement
Z
Rd


Z - 1,
(Z)
None
2(1)(2)
LDD
Rd, Z+q
Load Indirect with Displacement
Rd

(Z + q)
None
2(1)(2)
STS
k, Rr
Store Direct to Data Space
(k)

Rd
None
2(1)
ST
X, Rr
Store Indirect
(X)

Rr
None
1(1)
ST
X+, Rr
Store Indirect and Post-Increment
(X)
X


Rr,
X+1
None
1(1)
ST
-X, Rr
Store Indirect and Pre-Decrement
X
(X)


X - 1,
Rr
None
2(1)
ST
Y, Rr
Store Indirect
(Y)

Rr
None
1(1)
ST
Y+, Rr
Store Indirect and Post-Increment
(Y)
Y


Rr,
Y+1
None
1(1)
ST
-Y, Rr
Store Indirect and Pre-Decrement
Y
(Y)


Y - 1,
Rr
None
2(1)
STD
Y+q, Rr
Store Indirect with Displacement
(Y + q)

Rr
None
2(1)
ST
Z, Rr
Store Indirect
(Z)

Rr
None
1(1)
ST
Z+, Rr
Store Indirect and Post-Increment
(Z)
Z


Rr
Z+1
None
1(1)
ST
-Z, Rr
Store Indirect and Pre-Decrement
Z

Z-1
None
2(1)
STD
Z+q,Rr
Store Indirect with Displacement
(Z + q)

Rr
None
2(1)
Load Program Memory
R0

(Z)
None
3
LPM
Operation
LPM
Rd, Z
Load Program Memory
Rd

(Z)
None
3
LPM
Rd, Z+
Load Program Memory and Post-Increment
Rd
Z


(Z),
Z+1
None
3
Extended Load Program Memory
R0

(RAMPZ:Z)
None
3
ELPM
ELPM
Rd, Z
Extended Load Program Memory
Rd

(RAMPZ:Z)
None
3
ELPM
Rd, Z+
Extended Load Program Memory and PostIncrement
Rd
Z


(RAMPZ:Z),
Z+1
None
3
Store Program Memory
(RAMPZ:Z)

R1:R0
None
-
(RAMPZ:Z)
Z


R1:R0,
Z+2
None
-
Rd

I/O(A)
None
1
I/O(A)

Rr
None
1
STACK

Rr
None
1(1)
Rd

STACK
None
2(1)
Rd(n+1)
Rd(0)
C



Rd(n),
0,
Rd(7)
Z,C,N,V,H
1
Rd(n)
Rd(7)
C



Rd(n+1),
0,
Rd(0)
Z,C,N,V
1
SPM
SPM
Z+
Store Program Memory and Post-Increment
by 2
IN
Rd, A
In From I/O Location
OUT
A, Rr
Out To I/O Location
PUSH
Rr
Push Register on Stack
POP
Rd
Pop Register from Stack
Bit and Bit-test Instructions
LSL
Rd
Logical Shift Left
LSR
Rd
Logical Shift Right
56
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Mnemonics
Operands
Description
Operation
ROL
Rd
Rotate Left Through Carry
ROR
Rd
ASR
Flags
#Clocks
Rd(0)
Rd(n+1)
C



C,
Rd(n),
Rd(7)
Z,C,N,V,H
1
Rotate Right Through Carry
Rd(7)
Rd(n)
C



C,
Rd(n+1),
Rd(0)
Z,C,N,V
1
Rd
Arithmetic Shift Right
Rd(n)

Rd(n+1), n=0..6
Z,C,N,V
1
SWAP
Rd
Swap Nibbles
Rd(3..0)

Rd(7..4)
None
1
BSET
s
Flag Set
SREG(s)

1
SREG(s)
1
BCLR
s
Flag Clear
SREG(s)

0
SREG(s)
1
SBI
A, b
Set Bit in I/O Register
I/O(A, b)

1
None
1
CBI
A, b
Clear Bit in I/O Register
I/O(A, b)

0
None
1
BST
Rr, b
Bit Store from Register to T
T

Rr(b)
T
1
BLD
Rd, b
Bit load from T to Register
Rd(b)

T
None
1
SEC
Set Carry
C

1
C
1
CLC
Clear Carry
C

0
C
1
SEN
Set Negative Flag
N

1
N
1
CLN
Clear Negative Flag
N

0
N
1
SEZ
Set Zero Flag
Z

1
Z
1
CLZ
Clear Zero Flag
Z

0
Z
1
SEI
Global Interrupt Enable
I

1
I
1
CLI
Global Interrupt Disable
I

0
I
1
SES
Set Signed Test Flag
S

1
S
1
CLS
Clear Signed Test Flag
S

0
S
1
SEV
Set Two’s Complement Overflow
V

1
V
1
CLV
Clear Two’s Complement Overflow
V

0
V
1
SET
Set T in SREG
T

1
T
1
CLT
Clear T in SREG
T

0
T
1
SEH
Set Half Carry Flag in SREG
H

1
H
1
CLH
Clear Half Carry Flag in SREG
H

0
H
1
MCU Control Instructions
BREAK
Break
NOP
No Operation
SLEEP
Sleep
WDR
Watchdog Reset
Notes:
(See specific descr. for BREAK)
None
1
None
1
(see specific descr. for Sleep)
None
1
(see specific descr. for WDR)
None
1
1. Cycle times for Data memory accesses assume internal memory accesses, and are not valid
for accesses via the external RAM interface.
2. One extra cycle must be added when accessing Internal SRAM.
57
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
33. Packaging information
33.1
44A
PIN 1 IDENTIFIER
PIN 1
e
B
E1
E
D1
D
C
0°~7°
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
2010-10-20
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44A, 44-lead, 10 x 10mm body size, 1.0mm body thickness,
0.8 mm lead pitch, thin profile plastic quad flat package (TQFP)
DRAWING NO.
REV.
44A
C
58
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
33.2
44M1
D
Marked Pin# 1 ID
E
SEATING PLANE
A1
TOP VIEW
A3
A
K
L
Pin #1 Corner
D2
1
2
3
Option A
SIDE VIEW
Pin #1
Triangle
E2
Option B
K
Option C
b
e
Pin #1
Chamfer
(C 0.30)
Pin #1
Notch
(0.20 R)
BOTTOM VIEW
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
NOM
MAX
A
0.80
0.90
1.00
A1
–
0.02
0.05
A3
0.20 REF
b
0.18
0.23
0.30
D
6.90
7.00
7.10
D2
5.00
5.20
5.40
E
6.90
7.00
7.10
E2
5.00
5.20
5.40
e
Note: JEDEC Standard MO-220, Fig. 1 (SAW Singulation) VKKD-3.
NOTE
0.50 BSC
L
0.59
0.64
0.69
K
0.20
0.26
0.41
9/26/08
Package Drawing Contact:
[email protected]
TITLE
44M1, 44-pad, 7 x 7 x 1.0mm body, lead
pitch 0.50mm, 5.20mm exposed pad, thermally
enhanced plastic very thin quad flat no
lead package (VQFN)
GPC
ZWS
DRAWING NO.
REV.
44M1
H
59
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
33.3
49C2
E
A1 BALL ID
0.10
D
A1
TOP VIEW
A
A2
SIDE VIEW
E1
G
e
F
E
D
D1
COMMON DIMENSIONS
(Unit of Measure = mm)
C
B
1
A1 BALL CORNER
MIN
NOM
MAX
A
–
–
1.00
A1
0.20
–
–
A2
0.65
–
–
D
4.90
5.00
5.10
SYMBOL
A
2
3
4
5
b
6
7
e
BOTTOM VIEW
49 - Ø0.35 ±0.05
D1
E
3.90 BSC
4.90
5.00
E1
b
NOTE
5.10
3.90 BSC
0.30
0.35
e
0.40
0.65 BSC
3/14/08
Package Drawing Contact:
[email protected]
TITLE
49C2, 49-ball (7 x 7 array), 0.65mm pitch,
5.0 x 5.0 x 1.0mm, very thin, fine-pitch
ball grid array package (VFBGA)
GPC
CBD
DRAWING NO.
REV.
49C2
A
60
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34. Electrical Characteristics
All typical values are measured at T = 25C unless other temperature condition is given. All minimum and maximum values are valid across operating temperature and voltage unless other
conditions are given.
34.1
Absolute Maximum Ratings*
Operating Temperature.................................. -55C to +125C
*NOTICE:
Storage Temperature ..................................... -65C to +150C
Voltage on any Pin with respect to Ground..-0.5V to VCC+0.5V
Maximum Operating Voltage ............................................ 3.6V
DC Current per I/O Pin ............................................... 20.0 mA
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
DC Current VCC and GND Pins................................ 200.0 mA
34.2
DC Characteristics
Table 34-1.
Symbol
Current Consumption
Parameter
Condition
Min.
Typ.
Max.
VCC = 1.8V
30
VCC = 3.0V
75
VCC = 1.8V
260
VCC = 3.0V
570
VCC = 1.8V
510
690
VCC = 3.0V
1.1
1.49
VCC = 3.0V
11.4
13
VCC = 1.8V
2.8
VCC = 3.0V
4.8
VCC = 1.8V
80
VCC = 3.0V
150
VCC = 1.8V
160
225
VCC = 3.0V
295
390
VCC = 3.0V
4.8
6
All Functions Disabled, T = 25°C
VCC = 3.0V
0.1
3
All Functions Disabled, T = 85°C
VCC = 3.0V
1.5
5
VCC = 1.8V
1.1
6
VCC = 3.0V
1.1
6
VCC = 3.0V
2.6
10
32 kHz, Ext. Clk
1 MHz, Ext. Clk
Active
2 MHz, Ext. Clk
32 MHz, Ext. Clk
(1)
Power Supply Current
32 kHz, Ext. Clk
ICC
1 MHz, Ext. Clk
Idle
2 MHz, Ext. Clk
32 MHz, Ext. Clk
Power-down mode
ULP, WDT, Sampled BOD, T = 25°C
ULP, WDT, Sampled BOD, T= 85°C
Units
µA
mA
µA
mA
µA
61
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Table 34-1.
Symbol
Current Consumption (Continued)
Parameter
Condition
Power-save mode
RTC 1 kHz from Low Power 32 kHz
TOSC, T = 25°C
ICC
Reset Current
Consumption
Min.
Typ.
Max.
VCC = 1.8V
0.5
4
VCC = 3.0V
0.7
4
RTC from Low Power 32 kHz TOSC
VCC = 3.0V
1.16
without Reset pull-up resistor current
VCC = 3.0V
505
Units
µA
Module current consumption(2)
RC32M
RC32M w/DFLL
470
Internal 32.768 kHz oscillator as DFLL source
RC2M
RC2M w/DFLL
112
Internal 32.768 kHz oscillator as DFLL source
RC32K
PLL
ICC
600
145
30
Multiplication factor = 10x
225
Watchdog normal mode
0.9
BOD Continuous mode
120
BOD Sampled mode
1
Internal 1.00 V ref
80
Temperature reference
80
RTC with int. 32 kHz RC
as source
No prescaling
30
RTC with ULP as source
No prescaling
0.9
ADC
250 kS/s - Int. 1V Ref
2.9
DAC Normal Mode
Single channel, Int. 1V Ref
2.4
DAC Low-Power Mode
Single channel, Int. 1V Ref
1.1
AC High-speed
280
AC Low-power
110
USART
Rx and Tx enabled, 9600 BAUD
µA
mA
5.3
µA
DMA
Timer/Counter
95
Prescaler DIV1
AES
Flash/EEPROM
Programming
Note:
19
140
Vcc = 2V
13
Vcc = 3V
18
mA
1. All Power Reduction Registers set.
2. All parameters measured as the difference in current consumption between module enabled and disabled. All data at
VCC = 3.0V, ClkSYS = 1 MHz External clock with no prescaling.
62
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34.3
Speed
Table 34-2.
Symbol
ClkCPU
Operating voltage and frequency
Parameter
Condition
CPU clock frequency
Min
Typ
Max
VCC = 1.6V
0
12
VCC = 1.8V
0
12
VCC = 2.7V
0
32
VCC = 3.6V
0
32
Units
MHz
The maximum CPU clock frequency of the XMEGA A4 devices is depending on VCC. As shown
in Figure 34-1 on page 63 the Frequency vs. VCC curve is linear between 1.8V < VCC < 2.7V.
Figure 34-1. Operating Frequency vs.Vcc
MHz
32
Safe Operating Area
12
1.6
1.8
2.7
3.6
V
63
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34.4
Flash and EEPROM Memory Characteristics
Table 34-3.
Symbol
Endurance and Data Retention
Parameter
Condition
Min
25°C
10K
85°C
10K
25°C
100
55°C
25
25°C
80K
85°C
30K
25°C
100
55°C
25
Typ
Max
Write/Erase cycles
Units
Cycle
Flash
Data retention
Year
Write/Erase cycles
Cycle
EEPROM
Data retention
Table 34-4.
Symbol
Programming time
Parameter
Condition
Chip Erase
(2)
Flash
EEPROM
Notes:
Year
Flash, EEPROM
Min
and SRAM Erase
Typ(1)
Max
Units
40
Page Erase
6
Page Write
6
Page WriteAutomatic Page Erase and Write
12
Page Erase
6
Page Write
6
Page WriteAutomatic Page Erase and Write
12
ms
1. Programming is timed from the internal 2 MHz oscillator.
2. EEPROM is not erased if the EESAVE fuse is programmed.
64
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34.5
ADC Characteristics
Table 34-5.
ADC Characteristics
Symbol
Parameter
Condition
Min
Typ
Max
Units
RES
Resolution
Programmable: 8/12
8
12
12
Bits
INL
Integral Non-Linearity
500 ksps
-5
±2
5
DNL
Differential Non-Linearity
500 ksps
LSB
< ±1
Gain Error
< ±10
Offset Error
< ±2
mV
ADCclk
ADC Clock frequency
Max is 1/4 of Peripheral Clock
Conversion rate
Conversion time
(propagation delay)
(RES+2)/2+GAIN
RES = 8 or 12, GAIN = 0 or 1
Sampling Time
1/2 ADCclk cycle
5
Analog Supply Voltage
VREF
Reference voltage
kHz
2000
ksps
8
ADCclk
cycles
0.25
Conversion range
AVCC
7
2000
uS
0
VREF
Vcc-0.3
Vcc+0.3
1.0
Vcc-0.6V
Input bandwidth
INT1V
kHz
(1)
Internal 1.00V reference
1.00
INTVCC
Internal VCC/1.6
VCC/1.6
SCALEDVCC
Scaled internal VCC/10 input
VCC/10
Reference input resistance
> 10
RAREF
Start-up time
Internal input sampling speed
Note:
12
Temp. sensor, VCC/10, Bandgap
V
M
24
ADCclk
cycles
100
ksps
1. Refer to ”Bandgap Characteristics” on page 66 for more parameter details.
Table 34-6.
Symbol
ADC Gain Stage Characteristics
Parameter
Gain error
Condition
Min
1 to 64 gain
Noise level at input
Clock rate
Typ
Max
< ±1
Offset error
Vrms
V
Units
%
< ±1
VREF = Int. 1V
0.12
VREF = Ext. 2V
0.06
mV
64x gain
Same as ADC
1000
kHz
65
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34.6
DAC Characteristics
Table 34-7.
Symbol
DAC Characteristics
Parameter
Condition
INL
Integral Non-Linearity
VCC = 1.6-3.6V
DNL
Differential Non-Linearity
VCC = 1.6-3.6V
Fclk
Min
Typ
VREF = Ext. ref
±5
VREF = Ext. ref
<±1
VREF= AVCC
External reference voltage
1.1
Reference input impedance
1000
ksps
AVCC-0.6
V
M
>10
Max output voltage
Rload=100k
AVCC*0.98
Min output voltage
Rload=100k
<0.030
Offset factory calibration accuracy
Continues mode, VCC=3.0V,
VREF = Int 1.00V, T=85°C
Gain factory calibration accuracy
Units
LSB
Conversion rate
AREF
34.7
Max
V
±0.5
LSB
±2.5
Analog Comparator Characteristics
Table 34-8.
Symbol
Analog Comparator Characteristics
Parameter
Condition
Input Offset Voltage
VCC = 1.6 - 3.6V
< ±10
mV
Input Leakage Current
VCC = 1.6 - 3.6V
< 1000
pA
Vhys1
Hysteresis, No
VCC = 1.6 - 3.6V
0
mV
Vhys2
Hysteresis, Small
VCC = 1.6 - 3.6V
mode = HS
20
Vhys3
Hysteresis, Large
VCC = 1.6 - 3.6V
mode = HS
40
90
Propagation delay
VCC = 3.0V, T= 85°C
mode = HS
tdelay
VCC = 1.6 - 3.6V
mode = LP
175
Voff
Ilk
34.8
Min
Typ
Max
Units
mV
ns
Bandgap Characteristics
Table 34-9.
Symbol
Bandgap Voltage Characteristics
Parameter
Condition
As reference to ADC or DAC
Min
Typ
Max
Units
1 Clk_PER + 2.5µs
Bandgap Startup Time
µs
As input to AC or ADC
1.5
Bandgap voltage
1.1
T= 85°C, After calibration
0.99
1
1.01
V
ADC/DAC ref
1
Variation over voltage and temperature
VCC = 1.6 - 3.6V, TA = -40C to
85C
±2
%
66
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34.9
Brownout Detection Characteristics
Table 34-10. Brownout Detection Characteristics(1)
Symbol
Parameter
Condition
BOD level 0 falling Vcc
Min
Typ
Max
1.62
1.63
1.7
BOD level 1 falling Vcc
1.9
BOD level 2 falling Vcc
2.17
BOD level 3 falling Vcc
2.43
BOD level 4 falling Vcc
2.68
BOD level 5 falling Vcc
2.96
BOD level 6 falling Vcc
3.22
BOD level 7 falling Vcc
3.49
Units
V
Hysteresis
Note:
BOD level 0-5
1
%
1. BOD is calibrated at 85°C within BOD level 0 values, and BOD level 0 is the default level.
34.10 PAD Characteristics
Table 34-11. PAD Characteristics
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
VOL
VOH
Output Low Voltage GPIO
Output High Voltage GPIO
Condition
Min
Typ
Max
VCC = 2.4 - 3.6V
0.7*VCC
VCC+0.5
VCC = 1.6 - 2.4V
0.8*VCC
VCC+0.5
VCC = 2.4 - 3.6V
-0.5
0.3*VCC
VCC = 1.6 - 2.4V
-0.5
0.2*VCC
IOH = 15 mA, VCC = 3.3V
0.4
0.76
IOH = 10 mA, VCC = 3.0V
0.3
0.64
IOH = 5 mA, VCC = 1.8V
0.2
0.46
V
IOH = -8 mA, VCC = 3.3V
2.6
3.0
IOH = -6 mA, VCC = 3.0V
2.1
2.7
IOH = -2 mA, VCC = 1.8V
1.4
1.6
IIL
Input Leakage Current I/O pin
<0.001
1
IIH
Input Leakage Current I/O pin
<0.001
1
RP
I/O pin Pull/Buss keeper Resistor
T= -40°C to 85°C
20
Reset pin Pull-up Resistor
T= -40°C to 85°C
20
Input hysteresis
VCC = 1.6 V - 3.6 V, T= -40°C to 85°C
0.5
RRST
Units
µA
k
V
67
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
34.11 POR Characteristics
Table 34-12. Power-on Reset Characteristics
Symbol
Parameter
VPOT-
POR threshold voltage falling VCC
VPOT+
POR threshold voltage rising VCC
Condition
Min
Typ
VCC falls faster than 1V/ms
0.4
0.8
VCC falls at 1V/ms or slower
0.8
1.3
Max
Units
V
1.3
1.59
Typ
Max
34.12 Reset Characteristics
Table 34-13. Reset Characteristics
Symbol
Parameter
Condition
Min
Minimum reset pulse width
Reset threshold voltage
90
VCC = 2.7 - 3.6V
0.45*VCC
VCC = 1.6 - 2.7V
0.42*VCC
Units
ns
V
34.13 Oscillator Characteristics
Table 34-14. Internal 32.768 kHz Oscillator Characteristics
Symbol
Parameter
Accuracy
Condition
Min
T = 85C, VCC = 3V,
After production calibration
Typ
-0.5
Max
Units
0.5
%
Max
Units
Table 34-15. Internal 2 MHz Oscillator Characteristics
Symbol
Parameter
Accuracy
DFLL Calibration step size
Condition
Min
T = 85C, VCC = 3V,
After production calibration
Typ
-1.5
1.5
%
T = 25C, VCC = 3V
0.15
Table 34-16. Internal 32 MHz Oscillator Characteristics
Symbol
Parameter
Accuracy
DFLL Calibration stepsize
Condition
Min
T = 85C, VCC = 3V,
After production calibration
Typ
-1.5
Max
Units
1.5
%
T = 25C, VCC = 3V
0.2
Table 34-17. Internal 32 kHz, ULP Oscillator Characteristics
Symbol
Parameter
Output frequency 32 kHz ULP OSC
Condition
T = 85C, VCC = 3.0V
Min
Typ
26
Max
Units
kHz
68
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Table 34-18. External 32.768kHz Crystal Oscillator and TOSC characteristics
Symbol
SF
Parameter
Condition
Min
Capacitive load matched to crystal
specification
Safety factor
Typ
Max
3
Recommended crystal equivalent
series resistance (ESR)
Crystal load capacitance 6.5pF
60
ESR/R1
Crystal load capacitance 9.0pF
35
Input capacitance between TOSC
pins
Normal mode
4.7
CIN_TOSC
Low power mode
5.2
Note:
Units
k
pF
1. See Figure 34-2 on page 69 for definition
Figure 34-2. TOSC input capacitance
CL1
CL2
Device internal
External
TOSC1
TOSC2
32.768 KHz crystal
The input capacitance between the TOSC pins is CL1 + CL2 in series as seen from the crystal
when oscillating without external capacitors.
Table 34-19. Device wake-up time from sleep
Symbol
Parameter
Condition(1)
Int. 32.768 kHz RC
Idle Sleep, Standby and Extended
Standby sleep mode
Min
Typ(2)
Max
Units
130
Int. 2 MHz RC
2
Ext. 2 MHz Clock
2
Int. 32 MHz RC
0.17
Int. 32.768 kHz RC
320
Int. 2 MHz RC
10.3
Ext. 2 MHz Clock
4.5
Int. 32 MHz RC
5.8
µS
Power-save and Power-down
Sleep mode
Notes:
1. Non-prescaled System Clock source.
2. Time from pin change on external interrupt pin to first available clock cycle. Additional interrupt response time is minimum 5
system clock source cycles.
69
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35. Typical Characteristics
35.1
Active Supply Current
Figure 35-1. Active Supply Current vs. Frequency
fSYS = 0 - 1.0 MHz External clock, T = 25°C.
700
3.3 V
600
3.0 V
ICC [uA]
500
2.7 V
400
2.2 V
300
1.8 V
200
100
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency [MHz]
Figure 35-2. Active Supply Current vs. Frequency
fSYS = 1 - 32 MHz External clock, T = 25°C.
14
ICC [mA]
3.3 V
12
3.0 V
10
2.7 V
8
6
2.2 V
4
1.8 V
2
0
0
4
8
12
16
20
24
28
32
Frequency [MHz]
70
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-3. Active Supply Current vs. Vcc
fSYS = 1.0 MHz External Clock.
800
85 °C
25 °C
-40 °C
700
600
ICC [uA]
500
400
300
200
100
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-4. Active Supply Current vs. VCC
fSYS = 32.768 kHz internal RC.
160
-40 °C
85 °C
25 °C
140
120
ICC [uA]
100
80
60
40
20
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
71
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-5. Active Supply Current vs. Vcc
fSYS = 2.0 MHz internal RC.
1600
85 °C
25 °C
-40 °C
1400
1200
ICC [uA]
1000
800
600
400
200
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-6. Active Supply Current vs. Vcc
fSYS = 32 MHz internal RC prescaled to 8 MHz.
7
-40 °C
25 °C
85 °C
6
ICC [mA]
5
4
3
2
1
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
72
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-7. Active Supply Current vs. Vcc
fSYS = 32 MHz internal RC.
16
-40 °C
25 °C
85 °C
14
12
ICC [mA]
10
8
6
4
2
0
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
VCC [V]
35.2
Idle Supply Current
Figure 35-8. Idle Supply Current vs. Frequency
fSYS = 0 - 1.0 MHz, T = 25°C.
180
3.3 V
160
3.0 V
140
2.7 V
ICC [uA]
120
100
2.2 V
80
1.8 V
60
40
20
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency [MHz]
73
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-9. Idle Supply Current vs. Frequency
fSYS = 1 - 32 MHz, T = 25°C.
6
3.3 V
5
3.0 V
2.7 V
ICC [mA]
4
3
2.2 V
2
1
1.8 V
0
0
4
8
12
16
20
24
28
32
Frequency [MHz]
Figure 35-10. Idle Supply Current vs. Vcc
fSYS = 1.0 MHz External Clock.
200
85 °C
25 °C
-40 °C
ICC [uA]
160
120
80
40
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
74
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-11. Idle Supply Current vs. Vcc
fSYS = 32.768 kHz internal RC.
40
85 °C
-40 °C
25 °C
35
30
ICC [uA]
25
20
15
10
5
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-12. Idle Supply Current vs. Vcc
fSYS = 2.0 MHz internal RC.
500
-40 °C
25 °C
85 °C
ICC [uA]
400
300
200
100
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
75
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-13. Idle Supply Current vs. Vcc
fSYS = 32 MHz internal RC prescaled to 8 MHz.
3000
-40 °C
25 °C
85 °C
2500
ICC [uA]
2000
1500
1000
500
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-14. Idle Supply Current vs. Vcc
fSYS = 32 MHz internal RC.
7
-40 °C
25 °C
85 °C
6
ICC [mA]
5
4
3
2
1
0
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
VCC [V]
76
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35.3
Power-down Supply Current
Figure 35-15. Power-down Supply Current vs. Temperature
1.8
3.3 V
3.0 V
2.7 V
2.2 V
1.8 V
1.6
1.4
ICC [uA]
1.2
1
0.8
0.6
0.4
0.2
0
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
Temperature [°C]
Figure 35-16. Power-down Supply Current vs. Temperature
With WDT and sampled BOD enabled.
3
3.3 V
3.0 V
2.7 V
2.2 V
1.8 V
2.5
ICC [uA]
2
1.5
1
0.5
0
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
Temperature [°C]
77
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35.4
Power-save Supply Current
Figure 35-17. Power-save Supply Current vs. Temperature
With WDT, sampled BOD and RTC from ULP enabled.
3
3.3 V
3.0 V
2.7 V
2.2 V
1.8 V
2.5
ICC [uA]
2
1.5
1
0.5
0
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
Temperature [°C]
35.5
Pin Pull-up
Figure 35-18. Reset Pull-up Resistor Current vs. Reset Pin Voltage
VCC = 1.8V.
100
IRESET [uA]
80
60
40
20
-40 °C
25 °C
85 °C
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VRESET [V]
78
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-19. Reset Pull-up Resistor Current vs. Reset Pin Voltage
VCC = 3.0V.
160
140
IRESET [uA]
120
100
80
60
40
-40 °C
25 °C
85 °C
20
0
0
0.5
1
1.5
2
2.5
3
VRESET [V]
Figure 35-20. Reset Pull-up Resistor Current vs. Reset Pin Voltage
VCC = 3.3V.
180
160
140
IRESET [uA]
120
100
80
60
40
-40 °C
25 °C
85 °C
20
0
0
0.5
1
1.5
2
2.5
3
VRESET [V]
79
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35.6
Pin Output Voltage vs. Sink/Source Current
Figure 35-21. I/O Pin Output Voltage vs. Source Current
Vcc = 1.8V.
2
-40 °C
25 °C
85 °C
1.8
1.6
VPIN [V]
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-12
-10
-8
-6
-4
-2
0
IPIN [mA]
Figure 35-22. I/O Pin Output Voltage vs. Source Current
Vcc = 3.0V.
3.5
-40 °C
25 °C
85 °C
3
VPIN [V]
2.5
2
1.5
1
0.5
0
-20
-18
-16
-14
-12
-10
-8
-6
-4
-2
0
IPIN [mA]
80
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-23. I/O Pin Output Voltage vs. Source Current
Vcc = 3.3V.
3.5
-40 °C
25 °C
85 °C
3
VPIN [V]
2.5
2
1.5
1
0.5
0
-20
-18
-16
-14
-12
-10
-8
-6
-4
-2
0
IPIN [mA]
Figure 35-24. I/O Pin Output Voltage vs. Sink Current
Vcc = 1.8V.
85°C 25°C
1.8
1.6
1.4
VPIN [V]
1.2
-40 °C
1
0.8
0.6
0.4
0.2
0
0
2
4
6
8
10
12
14
16
18
20
IPIN [mA]
81
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-25. I/O Pin Output Voltage vs. Sink Current
Vcc = 3.0V.
0.7
85 °C
0.6
25 °C
-40 °C
VPIN [V]
0.5
0.4
0.3
0.2
0.1
0
0
2
4
6
8
10
12
14
16
18
20
IPIN [mA]
Figure 35-26. I/O Pin Output Voltage vs. Sink Current
Vcc = 3.3V.
VPIN [V]
0.7
0.6
85 °C
0.5
25 °C
-40 °C
0.4
0.3
0.2
0.1
0
0
2
4
6
8
10
12
14
16
18
20
IPIN [mA]
82
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35.7
Pin Thresholds and Hysteresis
Figure 35-27. I/O Pin Input Threshold Voltage vs. VCC
VIH - I/O Pin Read as “1”.
2.5
-40 °C
25 °C
85 °C
Vthreshold [V]
2
1.5
1
0.5
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-28. I/O Pin Input Threshold Voltage vs. VCC
VIL - I/O Pin Read as “0”.
1.8
85 °C
25 °C
-40 °C
1.6
1.4
Vthreshold [V]
1.2
1
0.8
0.6
0.4
0.2
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
83
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-29. I/O Pin Input Hysteresis vs. VCC.
0.7
0.6
Vthreshold [V]
0.5
85 °C
25 °C
-40 °C
0.4
0.3
0.2
0.1
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-30. Reset Input Threshold Voltage vs. VCC
VIH - I/O Pin Read as “1”.
1.8
-40 °C
25 °C
85 °C
1.6
VTHRESHOLD [V]
1.4
1.2
1
0.8
0.6
0.4
0.2
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
84
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-31. Reset Input Threshold Voltage vs. VCC
VIL - I/O Pin Read as “0”.
1.8
-40 °C
25 °C
85 °C
1.6
VTHRESHOLD [V]
1.4
1.2
1
0.8
0.6
0.4
0.2
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
35.8
Bod Thresholds
Figure 35-32. BOD Thresholds vs. Temperature
BOD Level = 1.6V.
1.645
1.64
VBOT [V]
1.635
1.63
Rising Vcc
1.625
1.62
Falling Vcc
1.615
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
Temperature [°C]
85
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-33. BOD Thresholds vs. Temperature
BOD Level = 2.9V.
3.03
3.02
3.01
Rising Vcc
VBOT [V]
3
2.99
2.98
2.97
2.96
Falling Vcc
2.95
2.94
2.93
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
Temperature [°C]
35.9
Analog Comparator
Figure 35-34. Analog Comparator Hysteresis vs. VCC
High-speed, Small hysteresis.
20
85 °C
16
VHYST [mV]
25 °C
-40 °C
12
8
4
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
86
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-35. Analog Comparator Hysteresis vs. VCC
High-speed, Large hysteresis.
60
50
85 °C
25 °C
-40 °C
VHYST [mV]
40
30
20
10
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 35-36. Analog Comparator Propagation Delay vs. VCC
High-speed.
180
162
144
126
tPD [ns]
108
85 °C
25 °C
-40 °C
90
72
54
36
18
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
87
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35.10 Oscillators and Wake-up Time
35.10.1
Internal 32.768 kHz Oscillator
Figure 35-37. Internal 32.768 kHz Oscillator Calibration Step Size
T = -40 to 85C, VCC = 3V.
0.80 %
Step size: f [kHz]
0.65 %
0.50 %
0.35 %
0.20 %
0.05 %
0
32
64
96
128
160
192
224
256
RC32KCAL[7..0]
35.10.2
Internal 2 MHz Oscillator
Figure 35-38. Internal 2 MHz Oscillator CALA Calibration Step Size
T = -40 to 85C, VCC = 3V.
0.50 %
0.40 %
Step size: f [MHz]
0.30 %
0.20 %
0.10 %
0.00 %
-0.10 %
-0.20 %
-0.30 %
0
16
32
48
64
80
96
112
128
DFLLRC2MCALA
88
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-39. Internal 2 MHz Oscillator CALB Calibration Step Size
T = -40 to 85C, VCC = 3V.
3.00 %
Step size: f [MHz]
2.50 %
2.00 %
1.50 %
1.00 %
0.50 %
0.00 %
0
8
16
24
32
40
48
56
64
112
128
DFLLRC2MCALB
35.10.3
Internal 32 MHZ Oscillator
Figure 35-40. Internal 32 MHz Oscillator CALA Calibration Step Size
T = -40 to 85C, VCC = 3V.
0.60 %
0.50 %
Step size: f [MHz]
0.40 %
0.30 %
0.20 %
0.10 %
0.00 %
-0.10 %
-0.20 %
0
16
32
48
64
80
96
DFLLRC32MCALA
89
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-41. Internal 32 MHz Oscillator CALB Calibration Step Size
T = -40 to 85C, VCC = 3V.
3.00 %
Step size: f [MHz]
2.50 %
2.00 %
1.50 %
1.00 %
0.50 %
0.00 %
0
8
16
24
32
40
48
56
64
DFLLRC32MCALB
35.11 Module current consumption
Figure 35-42. AC current consumption vs. Vcc
Low-power Mode.
Module current consumption [uA]
140
85 °C
25 °C
-40 °C
120
100
80
60
40
20
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
90
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 35-43. Power-up current consumption vs. Vcc
25 °C
600
-40 °C 85 °C
500
ICC [uA]
400
300
200
100
0
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VCC [V]
35.12 Reset Pulsewidth
Figure 35-44. Minimum Reset Pulse Width vs. Vcc
100
tRST [ns]
80
85 °C
25 °C
-40 °C
60
40
20
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
91
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
35.13 PDI Speed
Figure 35-45. PDI Speed vs. Vcc
35
25 °C
30
fMAX [MHz]
25
20
15
10
5
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
92
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
36. Errata
36.1
36.1.1
ATxmega16A4, ATxmega32A4
rev. A/B
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Bandgap voltage input for the ACs can not be changed when used for both ACs simultaneously
VCC voltage scaler for AC is non-linear
ADC has increased INL error for some operating conditions
ADC gain stage output range is limited to 2.4 V
ADC Event on compare match non-functional
Bandgap measurement with the ADC is non-functional when VCC is below 2.7V
Accuracy lost on first three samples after switching input to ADC gain stage
Configuration of PGM and CWCM not as described in XMEGA A Manual
PWM is not restarted properly after a fault in cycle-by-cycle mode
BOD: BOD will be enabled at any reset
Sampled BOD in Active mode will cause noise when bandgap is used as reference
DAC is nonlinear and inaccurate when reference is above 2.4V or VCC - 0.6V
DAC has increased INL or noise for some operating conditions
EEPROM page buffer always written when NVM DATA0 is written
Pending full asynchronous pin change interrupts will not wake the device
Pin configuration does not affect Analog Comparator Output
NMI Flag for Crystal Oscillator Failure automatically cleared
Flash Power Reduction Mode can not be enabled when entering sleep
Crystal start-up time required after power-save even if crystal is source for RTC
RTC Counter value not correctly read after sleep
Pending asynchronous RTC-interrupts will not wake up device
TWI Transmit collision flag not cleared on repeated start
Clearing TWI Stop Interrupt Flag may lock the bus
TWI START condition at bus timeout will cause transaction to be dropped
TWI Data Interrupt Flag (DIF) erroneously read as set
WDR instruction inside closed window will not issue reset
1. Bandgap voltage input for the ACs cannot be changed when used for both ACs
simultaneously
If the Bandgap voltage is selected as input for one Analog Comparator (AC) and then
selected/deselected as input for another AC, the first comparator will be affected for up to
1 µs and could potentially give a wrong comparison result.
Problem fix/Workaround
If the Bandgap is required for both ACs simultaneously, configure the input selection for both
ACs before enabling any of them.
2. VCC voltage scaler for AC is non-linear
The 6-bit VCC voltage scaler in the Analog Comparators is non-linear.
93
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Figure 36-1. Analog Comparator Voltage Scaler vs. Scalefac
T = 25°C
3.5
3.3 V
3
2.7 V
VSCALE [V]
2.5
2
1.8 V
1.5
1
0.5
0
0
5
10
15
20
25
30
35
40
45
50
55
60
65
SCALEFAC
Problem fix/Workaround
Use external voltage input for the analog comparator if accurate voltage levels are needed
3. ADC has increased INL error for some operating conditions
Some ADC configurations or operating condition will result in increased INL error.
In signed mode INL is increased to:
– 6LSB for sample rates above 1Msps, and up to 8 LSB for 2Msps sample rate.
– 6LSB for reference voltage below 1.1V when VCC is above 3.0V.
– 20LSB for ambient temperature below 0 degree C and reference voltage below 1.3V.
In unsigned mode, the INL error cannot be guaranteed, and this mode should not be used.
Problem fix/Workaround
None, avoid using the ADC in the above configurations in order to prevent increased INL
error. Use the ADC in signed mode also for single ended measurements.
4. ADC gain stage output range is limited to 2.4 V
The amplified output of the ADC gain stage will never go above 2.4 V, hence the differential
input will only give correct output when below 2.4 V/gain. For the available gain settings, this
gives a differential input range of:
–
1x
gain:
2.4
V
–
2x
gain:
1.2
V
–
4x
gain:
0.6
V
–
8x
gain:
300
mV
–
16x
gain:
150
mV
–
32x
gain:
75
mV
–
64x
gain:
38
mV
94
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Problem fix/Workaround
Keep the amplified voltage output from the ADC gain stage below 2.4 V in order to get a correct result, or keep ADC voltage reference below 2.4 V.
5. ADC Event on compare match non-functional
ADC signalling event will be given at every conversion complete even if Interrupt mode (INTMODE) is set to BELOW or ABOVE.
Problem fix/Workaround
Enable and use interrupt on compare match when using the compare function.
6. Bandgap measurement with the ADC is non-functional when VCC is below 2.7V
The ADC can not be used to do bandgap measurements when VCC is below 2.7V.
Problem fix/Workaround
None.
7. Accuracy lost on first three samples after switching input to ADC gain stage
Due to memory effect in the ADC gain stage, the first three samples after changing input
channel must be disregarded to achieve 12-bit accuracy.
Problem fix/Workaround
Run three ADC conversions and discard these results after changing input channels to ADC
gain stage.
8. Configuration of PGM and CWCM not as described in XMEGA A Manual
Enabling Common Waveform Channel Mode will enable Pattern generation mode (PGM),
but not Common Waveform Channel Mode.
Enabling Pattern Generation Mode (PGM) and not Common Waveform Channel Mode
(CWCM) will enable both Pattern Generation Mode and Common Waveform Channel Mode.
Problem fix/Workaround
Table 36-1. Configure PWM and CWCM according to this table:
PGM
CWCM
Description
0
0
PGM and CWCM disabled
0
1
PGM enabled
1
0
PGM and CWCM enabled
1
1
PGM enabled
9. PWM is not restarted properly after a fault in cycle-by-cycle mode
When the AWeX fault restore mode is set to cycle-by-cycle, the waveform output will not
return to normal operation at first update after fault condition is no longer present.
Problem fix/Workaround
Do a write to any AWeX I/O register to re-enable the output.
10. BOD will be enabled after any reset
If any reset source goes active, the BOD will be enabled and keep the device in reset if the
VCC voltage is below the programmed BOD level. During Power-On Reset, reset will not be
released until VCC is above the programmed BOD level even if the BOD is disabled.
95
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Problem fix/Workaround
Do not set the BOD level higher than VCC even if the BOD is not used.
11. Sampled BOD in Active mode will cause noise when bandgap is used as reference
Using the BOD in sampled mode when the device is running in Active or Idle mode will add
noise on the bandgap reference for ADC, DAC and Analog Comparator.
Problem fix/Workaround
If the bandgap is used as reference for either the ADC, DAC or the Analog Comparator, the
BOD must not be set in sampled mode.
12. DAC is nonlinear and inaccurate when reference is above 2.4V or VCC - 0.6V
Using the DAC with a reference voltage above 2.4V or VCC - 0.6V will give inaccurate output when converting codes that give below 0.75V output:
– ±10 LSB for continuous mode
– ±200 LSB for Sample and Hold mode
Problem fix/Workaround
None.
13. DAC has increased INL or noise for some operating conditions
Some DAC configurations or operating condition will result in increased output error.
– Continous mode: ±5 LSB
– Sample and hold mode: ±15 LSB
– Sample and hold mode for reference above 2.0v: up to ±100 LSB
Problem fix/Workaround
None.
14. EEPROM page buffer always written when NVM DATA0 is written
If the EEPROM is memory mapped, writing to NVM DATA0 will corrupt data in the EEPROM
page buffer.
Problem fix/Workaround
Before writing to NVM DATA0, for example when doing software CRC or flash page buffer
write, check if EEPROM page buffer active loading flag (EELOAD) is set. Do not write NVM
DATA0 when EELOAD is set.
15. Pending full asynchronous pin change interrupts will not wake the device
Any full asynchronous pin-change Interrupt from pin 2, on any port, that is pending when the
sleep instruction is executed, will be ignored until the device is woken from another source
or the source triggers again. This applies when entering all sleep modes where the System
Clock is stopped.
Problem fix/Workaround
None.
16. Pin configuration does not affect Analog Comparator output
The Output/Pull and inverted pin configuration does not affect the Analog Comparator
output.
Problem fix/Workaround
None for Output/Pull configuration.
96
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
For inverted I/O, configure the Analog Comparator to give an inverted result (i.e. connect
positive input to the negative AC input and vice versa), or use and external inverter to
change polarity of Analog Comparator output.
17. NMI Flag for Crystal Oscillator Failure automatically cleared
NMI flag for Crystal Oscillator Failure (XOSCFDIF) will be automatically cleared when executing the NMI interrupt handler.
Problem fix/Workaround
This device revision has only one NMI interrupt source, so checking the interrupt source in
software is not required.
18. Flash Power Reduction Mode can not be enabled when entering sleep
If Flash Power Reduction Mode is enabled when entering Power-save or Extended Standby
sleep mode, the device will only wake up on every fourth wake-up request. If Flash Power
Reduction Mode is enabled when entering Idle sleep mode, the wake-up time will vary with
up to 16 CPU clock cycles.
Problem fix/Workaround
Disable Flash Power Reduction mode before entering sleep mode.
19. Crystal start-up time required after power-save even if crystal is source for RTC
Even if 32.768 kHz crystal is used for RTC during sleep, the clock from the crystal will not be
ready for the system before the specified start-up time. See "XOSCSEL[3:0]: Crystal Oscillator Selection" in XMEGA A Manual. If BOD is used in active mode, the BOD will be on during
this period (0.5s).
Problem fix/Workaround
If faster start-up is required, go to sleep with internal oscillator as system clock.
20. RTC Counter value not correctly read after sleep
If the RTC is set to wake up the device on RTC Overflow and bit 0 of RTC CNT is identical to
bit 0 of RTC PER as the device is entering sleep, the value in the RTC count register can not
be read correctly within the first prescaled RTC clock cycle after wakeup. The value read will
be the same as the value in the register when entering sleep.
The same applies if RTC Compare Match is used as wake-up source.
Problem fix/Workaround
Wait at least one prescaled RTC clock cycle before reading the RTC CNT value.
21. Pending asynchronous RTC-interrupts will not wake up device
Asynchronous Interrupts from the Real-Time-Counter that is pending when the sleep
instruction is executed, will be ignored until the device is woken from another source or the
source triggers again.
Problem fix/Workaround
None.
22. TWI Transmit collision flag not cleared on repeated start
The TWI transmit collision flag should be automatically cleared on start and repeated start,
but is only cleared on start.
Problem fix/Workaround
Clear the flag in software after address interrupt.
97
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
23. Clearing TWI Stop Interrupt Flag may lock the bus
If software clears the STOP Interrupt Flag (APIF) on the same Peripheral Clock cycle as the
hardware sets this flag due to a new address received, CLKHOLD is not cleared and the
SCL line is not released. This will lock the bus.
Problem fix/Workaround
Check if the bus state is IDLE. If this is the case, it is safe to clear APIF. If the bus state is
not IDLE, wait for the SCL pin to be low before clearing APIF.
Code:
/* Only clear the interrupt flag if within a "safe zone". */
while ( /* Bus not IDLE: */
((COMMS_TWI.MASTER.STATUS & TWI_MASTER_BUSSTATE_gm) !=
TWI_MASTER_BUSSTATE_IDLE_gc)) &&
/* SCL not held by slave: */
!(COMMS_TWI.SLAVE.STATUS & TWI_SLAVE_CLKHOLD_bm)
)
{
/* Ensure that the SCL line is low */
if ( !(COMMS_PORT.IN & PIN1_bm) )
if ( !(COMMS_PORT.IN & PIN1_bm) )
break;
}
/* Check for an pending address match interrupt */
if ( !(COMMS_TWI.SLAVE.STATUS & TWI_SLAVE_CLKHOLD_bm) )
{
/* Safely clear interrupt flag */
COMMS_TWI.SLAVE.STATUS |= (uint8_t)TWI_SLAVE_APIF_bm;
}
24. TWI START condition at bus timeout will cause transaction to be dropped
If Bus Timeout is enabled and a timeout occurs on the same Peripheral Clock cycle as a
START is detected, the transaction will be dropped.
Problem fix/Workaround
None.
25. TWI Data Interrupt Flag erroneously read as set
When issuing the TWI slave response command CMD=0b11, it takes 1 Peripheral Clock
cycle to clear the data interrupt flag (DIF). A read of DIF directly after issuing the command
will show the DIF still set.
Problem fix/Workaround
Add one NOP instruction before checking DIF.
26. WDR instruction inside closed window will not issue reset
When a WDR instruction is execute within one ULP clock cycle after updating the window
control register, the counter can be cleared without giving a system reset.
Problem fix/Workaround
Wait at least one ULP clock cycle before executing a WDR instruction.
98
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
37. Datasheet Revision History
Please note that the referring page numbers in this section are referred to this document. The
referring revisions in this section are referring to the document revision.
37.1
37.2
37.3
37.4
8069R – 06/13
1.
Not recommended for new designs - Use XMEGA A4U series.
1.
Datasheet status changed to complete: Preliminary removed from the front page.
2.
Updated all tables in the “Electrical Characteristics” .
3.
Updated ”Packaging information” on page 58.
4.
Replaced Table 34-11 on page 67.
5.
Replaced Table 34-18 on page 69 and added the figure ”TOSC input capacitance” on page 69.
7.
ERRATA A combined with ERRATA B to ERRATA “rev. A/B” .
8.
Updated ERRATA for ADC (ADC has increased INL error for some operating conditions).
9.
Updated the last page by Atmel new Brand Style Guide.
1.
Updated ”Errata” on page 93.
1.
Updated the Footnote 3 of ”Ordering Information” on page 2.
2.
Updated ”Features” on page 27. Event Channel 0 output on port pin 7.
3.
Updated ”DC Characteristics” on page 61 by adding Icc for Flash/EEPROM Programming.
4.
Added AVCC in ”ADC Characteristics” on page 65.
5.
Updated Start up time in ”ADC Characteristics” on page 65.
6.
Updated ”DAC Characteristics” on page 66. Removed DC output impedence.
7.
Updated and fixed typo in “Errata” section.
8069Q – 12/10
8069P – 09/10
8069O – 08/10
99
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
37.5
37.6
37.7
37.8
37.9
8069N – 02/10
1.
Added ”PDI Speed” on page 92.
1.
Updated the device pin-out Figure 2-1 on page 3. PDI_CLK and PDI_DATA renamed only PDI.
2.
Updated ”Alternate Pin Functions Description” on page 49.
3.
Updated ”Alternate Pin Functions” on page 51.
4.
Updated ”Timer/Counter and AWEX functions” on page 49.
5.
Added Table 34-18 on page 69.
6.
Added Table 34-19 on page 69.
7.
Changed Internal Oscillator Speed to ”Oscillators and Wake-up Time” on page 88.
8.
Updated ”Errata” on page 93.
1.
Updated ”Flash and EEPROM Page Size” on page 14.
2.
Updated ”Electrical Characteristics” on page 61 with Max/Min numbers.
3.
Added ”Flash and EEPROM Memory Characteristics” on page 64.
4.
Updated Table 34-11 on page 67, Input hysteresis is in V and not in mV.
1.
Updated ”Ordering Information” on page 2.
2.
Updated ”Errata” on page 93
1.
Updated ”Electrical Characteristics” on page 61.
2.
Updated ”Typical Characteristics” on page 70.
3.
Editorial updates.
8069M – 02/10
8069L – 11/09
8069K – 06/09
8069J – 04/09
100
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
37.10 8069I – 03/09
1.
Updated ”Electrical Characteristics” on page 61.
2.
Updated ”Typical Characteristics” on page 70.
1.
Updated ”Ordering Information” on page 2.
2.
Added VFBGA to ”Pinout/Block Diagram” on page 3.
3.
Updated ”Block Diagram” on page 6.
4.
Updated feature list in ”Memories” on page 10.
5.
Added 49-balls VFBGA to ”Packaging information” on page 58.
1.
Updated ”Features” on page 1.
2.
Updated ”Ordering Information” on page 2.
3.
Replaced the package drawing ”44M1” on page 59 by a rev H update.
1.
Updated ”Features” on page 1.
2.
Updated ”Ordering Information” on page 2.
3.
Updated ”Features” on page 10 by removing “External Memory...”.
4.
Updated Figure 7-1 on page 11 and Figure 7-2 on page 12.
5.
Updated Table 7-2 on page 14 and Table 7-3 on page 14.
6.
Updated ADC ”Features” on page 41 and ”Overview” on page 41.
7.
Removed “Interrupt Vector Summary” section from datasheet.
1.
Changed Figure 2-1’s title to “Bock Diagram and TQFP/QFN pinout” .
2.
Updated Table 30-6 on page 52.
37.11 8069H – 11/08
37.12 8069G – 10/08
37.13 8069F – 09/08
37.14 8069E – 08/08
101
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
37.15 8069D – 08/08
1.
Updated ”Features” on page 1 and ”Overview” on page 5.
2.
Inserted ”Interrupt Vector Summary.” on page 52.
1.
Updated Figure 2-1 on page 3 and ”Pinout and Pin Functions” on page 49.
2.
Updated ”Overview” on page 5.
3.
Updated XMEGA A4 Block Diagram, Figure 3-1 on page 6 by removing JTAG from the block
diagram.
4.
Removed the sections related to JTAG: JTAG Reset and JTAG Interface.
5.
Updated Table 14-1 on page 25.
6.
Updated all tables in section ”Alternate Pin Functions” on page 51.
1.
Updated ”Features” on page 1.
2.
Updated ”Pinout/Block Diagram” on page 3 and ”Pinout and Pin Functions” on page 49.
3.
Updated ”Ordering Information” on page 2.
4.
Updated ”Overview” on page 5, included the XMEGA A4 explanation text on page 6.
5.
Added XMEGA A4 Block Diagram, Figure 3-1 on page 6.
6.
Updated AVR CPU ”Features” on page 8 and Updated Figure 6-1 on page 8.
7.
Updated Event System block diagram, Figure 9-1 on page 17.
8.
Updated ”PMIC - Programmable Multi-level Interrupt Controller” on page 25.
9.
Updated ”AC - Analog Comparator” on page 44.
10.
Updated ”I/O configuration” on page 27.
11.
Inserted a new Figure 16-1 on page 32.
12.
Updated ”Peripheral Module Address Map” on page 53.
13.
Inserted ”Instruction Set Summary” on page 54.
14.
Added Speed grades in ”Speed” on page 63.
1.
Initial revision.
37.16 8069C – 06/08
37.17 8069B – 06/08
37.18 8069A – 02/08
102
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
Table of Contents
Features ..................................................................................................... 1
Typical Applications ................................................................................ 1
1
Ordering Information ............................................................................... 2
2
Pinout/Block Diagram .............................................................................. 3
3
Overview ................................................................................................... 5
3.1Block Diagram ...........................................................................................................6
4
Resources ................................................................................................. 7
4.1Recommended reading .............................................................................................7
5
Disclaimer ................................................................................................. 7
6
AVR CPU ................................................................................................... 8
6.1Features ....................................................................................................................8
6.2Overview ...................................................................................................................8
6.3Register File ..............................................................................................................9
6.4ALU - Arithmetic Logic Unit .......................................................................................9
6.5Program Flow ............................................................................................................9
7
Memories ................................................................................................ 10
7.1Features ..................................................................................................................10
7.2Overview .................................................................................................................10
7.3In-System Programmable Flash Program Memory .................................................11
7.4Data Memory ...........................................................................................................12
7.5Production Signature Row .......................................................................................13
7.6User Signature Row ................................................................................................13
7.7Flash and EEPROM Page Size ...............................................................................14
8
DMAC - Direct Memory Access Controller .......................................... 15
8.1Features ..................................................................................................................15
8.2Overview .................................................................................................................15
9
Event System ......................................................................................... 16
9.1Features ..................................................................................................................16
9.2Overview .................................................................................................................16
10 System Clock and Clock options ......................................................... 18
10.1Features ................................................................................................................18
i
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
10.2Overview ...............................................................................................................18
10.3Clock Options ........................................................................................................19
11 Power Management and Sleep Modes ................................................. 21
11.1Features ................................................................................................................21
11.2Overview ...............................................................................................................21
11.3Sleep Modes .........................................................................................................21
12 System Control and Reset .................................................................... 23
12.1Features ................................................................................................................23
12.2Resetting the AVR .................................................................................................23
12.3Reset Sources .......................................................................................................23
13 WDT - Watchdog Timer ......................................................................... 24
13.1Features ................................................................................................................24
13.2Overview ...............................................................................................................24
14 PMIC - Programmable Multi-level Interrupt Controller ....................... 25
14.1Features ................................................................................................................25
14.2Overview ...............................................................................................................25
14.3Interrupt vectors ....................................................................................................25
15 I/O Ports .................................................................................................. 27
15.1Features ................................................................................................................27
15.2Overview ...............................................................................................................27
15.3I/O configuration ....................................................................................................27
15.4Input sensing .........................................................................................................30
15.5Port Interrupt .........................................................................................................30
15.6Alternate Port Functions ........................................................................................30
16 T/C - 16-bit Timer/Counter ..................................................................... 31
16.1Features ................................................................................................................31
16.2Overview ...............................................................................................................31
17 AWEX - Advanced Waveform Extension ............................................. 33
17.1Features ................................................................................................................33
17.2Overview ...............................................................................................................33
18 Hi-Res - High Resolution Extension ..................................................... 34
18.1Features ................................................................................................................34
18.2Overview ...............................................................................................................34
ii
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
19 RTC - 16-bit Real-Time Counter ............................................................ 35
19.1Features ................................................................................................................35
19.2Overview ...............................................................................................................35
20 TWI - Two-Wire Interface ....................................................................... 36
20.1Features ................................................................................................................36
20.2Overview ...............................................................................................................36
21 SPI - Serial Peripheral Interface ............................................................ 37
21.1Features ................................................................................................................37
21.2Overview ...............................................................................................................37
22 USART ..................................................................................................... 38
22.1Features ................................................................................................................38
22.2Overview ...............................................................................................................38
23 IRCOM - IR Communication Module .................................................... 39
23.1Features ................................................................................................................39
23.2Overview ...............................................................................................................39
24 Crypto Engine ........................................................................................ 40
24.1Features ................................................................................................................40
24.2Overview ...............................................................................................................40
25 ADC - 12-bit Analog to Digital Converter ............................................. 41
25.1Features ................................................................................................................41
25.2Overview ...............................................................................................................41
26 DAC - 12-bit Digital to Analog Converter ............................................. 43
26.1Features ................................................................................................................43
26.2Overview ...............................................................................................................43
27 AC - Analog Comparator ....................................................................... 44
27.1Features ................................................................................................................44
27.2Overview ...............................................................................................................44
27.3Input Selection .......................................................................................................46
27.4Window Function ...................................................................................................46
28 OCD - On-chip Debug ............................................................................ 47
28.1Features ................................................................................................................47
28.2Overview ...............................................................................................................47
29 Program and Debug Interfaces ............................................................. 48
iii
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
XMEGA A4
29.1Features ................................................................................................................48
29.2Overview ...............................................................................................................48
29.3PDI - Program and Debug Interface ......................................................................48
30 Pinout and Pin Functions ...................................................................... 49
30.1Alternate Pin Functions Description ......................................................................49
30.2Alternate Pin Functions .........................................................................................51
31 Peripheral Module Address Map .......................................................... 53
32 Instruction Set Summary ...................................................................... 54
33 Packaging information .......................................................................... 58
33.144A ........................................................................................................................58
33.244M1 .....................................................................................................................59
33.349C2 ......................................................................................................................60
34 Electrical Characteristics ...................................................................... 61
34.1Absolute Maximum Ratings* .................................................................................61
34.2DC Characteristics ................................................................................................61
34.3Speed ....................................................................................................................63
34.4Flash and EEPROM Memory Characteristics .......................................................64
34.5ADC Characteristics ..............................................................................................65
34.6DAC Characteristics ..............................................................................................66
34.7Analog Comparator Characteristics .......................................................................66
34.8Bandgap Characteristics .......................................................................................66
34.9Brownout Detection Characteristics ......................................................................67
34.10PAD Characteristics ............................................................................................67
34.11POR Characteristics ...........................................................................................68
34.12Reset Characteristics ..........................................................................................68
34.13Oscillator Characteristics .....................................................................................68
35 Typical Characteristics .......................................................................... 70
35.1Active Supply Current ............................................................................................70
35.2Idle Supply Current ................................................................................................73
35.3Power-down Supply Current .................................................................................77
35.4Power-save Supply Current ..................................................................................78
35.5Pin Pull-up .............................................................................................................78
35.6Pin Output Voltage vs. Sink/Source Current .........................................................80
35.7Pin Thresholds and Hysteresis ..............................................................................83
iv
8069R–AVR–06/2013
Not recommended for new designs Use XMEGA A4U series
35.8Bod Thresholds .....................................................................................................85
35.9Analog Comparator ...............................................................................................86
35.10Oscillators and Wake-up Time ............................................................................88
35.11Module current consumption ...............................................................................90
35.12Reset Pulsewidth .................................................................................................91
35.13PDI Speed ...........................................................................................................92
36 Errata ....................................................................................................... 93
36.1ATxmega16A4, ATxmega32A4 .............................................................................93
37 Datasheet Revision History .................................................................. 99
37.18069R – 06/13 .......................................................................................................99
37.28069Q – 12/10 .......................................................................................................99
37.38069P – 09/10 .......................................................................................................99
37.48069O – 08/10 .......................................................................................................99
37.58069N – 02/10 .....................................................................................................100
37.68069M – 02/10 ....................................................................................................100
37.78069L – 11/09 .....................................................................................................100
37.88069K – 06/09 .....................................................................................................100
37.98069J – 04/09 ......................................................................................................100
37.108069I – 03/09 ....................................................................................................101
37.118069H – 11/08 ...................................................................................................101
37.128069G – 10/08 ...................................................................................................101
37.138069F – 09/08 ...................................................................................................101
37.148069E – 08/08 ...................................................................................................101
37.158069D – 08/08 ...................................................................................................102
37.168069C – 06/08 ...................................................................................................102
37.178069B – 06/08 ...................................................................................................102
37.188069A – 02/08 ...................................................................................................102
Table of Contents....................................................................................... i
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
Hong Kong
Tel: (852) 2245-6100
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
[email protected]
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2010 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, AVR®, AVR® logo and others are registered trademarks, XMEGATM and others are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of
others.
8069R–AVR–06/2013