CleO Camera Module Datasheet

CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
Future Technology
Devices International
Limited
Datasheet
CleO-Camera Module
1 Introduction
1.1
The CleO-Camera module is a camera accessory for
the CleO series – the smart TFT display for Arduino.
It consists of an OV5640 sensor module and Flash
LEDs. The OV5640 sensor is a low voltage, highperformance, 1/4-inch 5 megapixel CMOS image
sensor that provides the full functionality of a single
chip 5 megapixel (2592×1944) camera using
OmniBSI™ technology in a small footprint package.
It is controlled through the standard Serial Camera
Control Bus (SCCB) interface.

1.4 µm x 1.4 µm pixel with OmniBSI™
technology for high performance (high
sensitivity, low crosstalk, low noise,
improved quantum efficiency)



Optical size 1/4"
Embedded 1.5V regulator for core power
The CleO-camera module is supplied with a standard
24 Pin 0.5mm pitch FFC cable.






Features
On-board regulator for VDDA,VDDIO,
only 3V3 supply needed
Support for output format: RAW RGB,
RGB565/555/444,
YUV422/420,
YCbCr422 and compression
Image quality control:color saturation,
hue,
gamma,
sharpness(edge
enhancement), lens correction, defective
pixel cancelling and noise cancelling
Support for anti-shake
Standard SCCB interface
In built Flash light LED
24 pin 0.5mm pitch FFC cable interface
N either the whole nor any part of the information contained in, or the product described in this manual, may be adapted or
reproduced in any material or elec tronic form without the prior written c onsent of the c opyright holder. T his product and its
doc umentation are s upplied on an as- is basis and no warranty as to their s uitability for any partic ular purpos e is either made or
implied. Future T ec hnology Devic es I nternational L td will not accept any claim for damages hows oever arising as a res ult of use or
failure of this produc t. Y our statutory rights are not affected. T his produc t or any variant of it is not intended for us e in any
medical appliance, device or s ystem in whi c h the failure of the produc t might reasonably be expected to res ult in pers onal injury.
T his doc ument provides preliminary information that may be s ubject to c hange without notice. N o freedom to use patents or other
intellec tual property rights is implied by the publication of this doc ument. Future Tec hnology D evices I nternational L td, U nit 1 , 2
Seaward P lac e, C enturion Business P ark, G lasgow G 4 1 1HH U nited Kingdom. Sc otland Registered C ompany N umber: SC 136640
Copyright © Future Technology Devices International Limited
1
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
2 Ordering Information
Part No.
Description
CleO-CAM1
CleO-camera module, 5M Pixel HD CMOS camera module with adaptor board
and FPC Flex
Copyright © Future Technology Devices International Limited
2
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
Table of Contents
1 Introduction ................................................................. 1
1.1
Features ................................................................................ 1
2 Ordering Information .................................................... 2
3 Pin Out and Signal Description ...................................... 4
3.1
Module Description ................................................................ 4
3.2
Module Interface Signal Desciption ......................................... 4
4 Devices Characteristics and Ratings............................... 6
4.1
Electrical Specification ........................................................... 6
4.2
Sensor Key Specification ........................................................ 7
5 Board Schematic ........................................................... 8
6 Mechanical Dimensions ................................................. 9
7 Contact Information .................................................... 10
Appendix A – References ................................................. 11
Document References ...................................................................11
Acronyms and Abbreviations .........................................................11
Appendix B - List of Figures and Tables ............................ 12
List of Tables ................................................................................12
List of Figures ...............................................................................12
Appendix C – Revision History.......................................... 13
Copyright © Future Technology Devices International Limited
3
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
3 Pin Out and Signal Description
3.1
Module Description
Figure 1 – Camera Module Features
No
Feature
1
2
3
4
5
2.8V fixed voltage LDO
LED driver
24pin 0.5 mm pitch FFC connector interface to OV5640 module
24pin 0.5 mm pitch FFC connector interface to CleO
White LED
6
OV5640 camera module
Reference
Designator
U7
U16
CN13
CN3
LED5, LED6, LED7,
LED8
-
Table 1 - Camera Module Features & Description
3.2
Module Interface Signal Desciption
The pin description of CN3 is given in Table 2.
Pin
No
Pin Name
Type
Description
1
PWM0
Input
Pulse Width Modulation to control LED brightness
2
CAM_5V
Power
5V Supply
3
CAM_D2
Output
Pixel Data Output 2
4
CAM_D1
Output
Pixel Data Output 1
5
CAM_D3
Output
Pixel Data Output 3
Copyright © Future Technology Devices International Limited
4
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
Pin
No
Pin Name
Type
Description
6
CAM_D0
Output
Pixel Data Output 0
7
CAM_D4
Output
Pixel Data Output 4
8
CAM_PCLK
Output
Pixel Clock Output from Sensor
9
CAM_D5
Output
Pixel Data Output 5
10
GND
Ground
Power Ground
11
CAM_D6
Output
Pixel Data Output 6
12
CAM_XCLK
Input
Master Clock into Sensor
13
CAM_D7
Output
Pixel Data Output 7
14
CAM_3V3
Power
3V3 Supply
15
CAM_3V3
Power
3V3 Supply
16
CAM_HD
Output
Active High: Line/Data Valid; indicates active pixels
17
CAM PWDN
Input
Camera Power Down, active High

Always pull low enable the sensor
18
CAM_VD
Output
Active High: Frame Valid; indicates active frame
19
RESETn
Input
Camera Reset, Active low
20
I2C0_SCL
Input
Two-Wire Serial Interface Clock
21
CAM_5V
Power
5V Supply
22
I2C0_SDA
Bi-Directional
Two-Wire Serial Interface Data I/O
23
GND
Ground
Power Ground
24
GND
Ground
Power Ground
Table 2 - CN3 Pin Description
Copyright © Future Technology Devices International Limited
5
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
4 Devices Characteristics and Ratings
4.1
Electrical Specification
Parameter
Value
Unit
Storage Temperature
-40°C to 95°C
Degrees C
Conditions
Ambient Operating Temperature (Power
-30°C to 70°C
Degrees C
Applied)
Table 3 - Temperature Parameter
DC Characteristics (Ambient Temperature = -30°C to +70°C)
Parameter
Description
Minimum
Typical
Maximum
Units
5.25
V
3.6
V
V
dc
5V DC input
4.75
V
dc
3V3 DC input
3.0
Vih
Input high voltage
1.26
Vil
Input low voltage
Voh
output high voltage
Vol
output low voltage
0.18
Table 4 - Operating Voltage and Current
3.3
Conditions
V
0.54
1.62
Copyright © Future Technology Devices International Limited
V
V
V
6
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
4.2
C learance N o.: FT DI# 4 9 4
Sensor Key Specification
Figure 2- Sensor Key Specifications
Copyright © Future Technology Devices International Limited
7
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
5 Board Schematic
Figure 3 - Camera Schematic
Copyright © Future Technology Devices International Limited
8
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
6 Mechanical Dimensions
Figure 4 - CleO - Camera Module Dimensions
Copyright © Future Technology Devices International Limited
9
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
7 Contact Information
Head Office – Glasgow, UK
Branch Office – Tigard, Oregon, USA
Future Technology Devices International Limited
Unit 1, 2 Seaward Place, Centurion Business Park
Glasgow G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
Future Technology Devices International Limited (USA)
7130 SW Fir Loop
Tigard, OR 97223-8160
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
Branch Office – Taipei, Taiwan
Branch Office – Shanghai, China
Future Technology Devices International Limited (Taiwan)
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan , R.O.C.
Tel: +886 (0) 2 8797 1330
Fax: +886 (0) 2 8751 9737
Future Technology Devices International Limited (China)
Room 1103, No. 666 West Huaihai Road,
Shanghai, 200052
C hina
Tel: +86 21 62351596
Fax: +86 21 62351595
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
tw .[email protected]
tw .[email protected]
tw .[email protected]
[email protected]
[email protected]
[email protected]
Web Site
http://ftdichip.com
Distributor and Sales Representatives
Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s)
in your country.
System and equipment manufac turers and des igners are res ponsible to ens ure that their s ys tems , and any Future T ec hno logy D evices
I nternational L td (FTDI ) devices incorporated in their sys tems , meet all applic able safety, regulatory and sys tem -level performance requirements .
All application- related information in this document (including applic ation desc riptions , s uggest ed FTDI devic es and other materials ) is provided
for referenc e only. While FTDI has taken care to ass ure it is acc urate, this information is s ubject to c ustomer confirmation, and FTDI disclaims all
liability for s ys tem des igns and for any applic ations ass istance provided by FTDI . Use of FTDI devic es in life s upport and/or s afety applic ations is
entirely at the user’s risk, and the us er agrees to defend, indemnify and hold harmless FTDI from any and all damages , claims , s uits or expense
res ulting from s uch us e. T his doc ument is s ubject to c hange without notice. N o freedom to us e patents or other intellec tual property rights is
implied by the public ation of this doc ument. N either the whole nor any part of the information c ontained in, or the produc t d esc ribed in this
doc ument, may be adapted or reproduc ed in any material or elec tronic form without the prior written c onsent of the c opyright holder. Future
Tec hnology Devices I nternational L td, U nit 1 , 2 Seaward P lac e, Centurion Business Park, Glas gow G41 1HH , U ni ted Kingdom. Scotland Registered
C ompany N umber: SC136640
Copyright © Future Technology Devices International Limited
10
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
Appendix A – References
Document References
For module documentations, please refer to URL below:
OV5640 datasheet: OV5640 Datasheet
LDO 2.8V Fixed Voltage datasheet: FT531GA Datasheet
Acronyms and Abbreviations
Terms
Description
DC
Direct Current
LED
Light-emitting diode
PWM
Pulse Width Modulation
SCCB
Serial Camera Control Bus
TFT
FFC/FPC
Thin Film Translator
Flexible Flat Cable/Flexible Printed Circuit
Copyright © Future Technology Devices International Limited
11
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
Appendix B - List of Figures and Tables
List of Tables
Table 1 - Camera Module Features & Description .................................................................................... 4
Table 2 - CN3 Pin Description ................................................................................................................. 5
Table 3 - Temperature Parameter........................................................................................................... 6
Table 4 - Operating Voltage and Current................................................................................................. 6
List of Figures
Figure 1 – Camera Module Features........................................................................................................ 4
Figure 2- Sensor Key Specifications ........................................................................................................ 7
Figure 3 - Camera Schematic ................................................................................................................. 8
Figure 4 - CleO - Camera Module Dimensions ......................................................................................... 9
Copyright © Future Technology Devices International Limited
12
CleO-Camera Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001308
C learance N o.: FT DI# 4 9 4
Appendix C – Revision History
Document Title:
CleO-Camera Module Datasheet
Document Reference No.:
FT_001308
Clearance No.:
FTDI# 494
Product Page:
http://www.ftdichip.com/Products/Modules/CleO.htm
Document Feedback:
Send Feedback
Revision
Changes
Date
Version 1.0
Initial Release
2016-04-20
Copyright © Future Technology Devices International Limited
13
Similar pages