V2DIP1-48 datasheet

Future Technology Devices International Ltd.
V2DIP1-48
VNC2-48 Development Module
Datasheet
Document Reference No.: FT_000236
Version 1.01
Issue Date: 2010-05-24
Future Technology Devices International Ltd (FTDI)
Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom
Tel.: +44 (0) 141 429 2777
Fax: + 44 (0) 141 429 2758
E-Mail (Support): [email protected]
Web: http://www.vinculum.com
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced
in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are
supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology
Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your
statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in
which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary
information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by
the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park,
Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640
Copyright © 2010 Future Technology Devices International Limited
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
1
Introduction
V2DIP1-48 module is designed to allow rapid development of designs using the VNC2-48Q IC. The
V2DIP1-48 is supplied as a PCB designed to fit into a 24 pin 0.6” wide 0.1” pitch DIP socket.The module
provides access to the UART, parallel FIFO, and SPI interface pins of the VNC2-48Q device, via onboard
header pins. The module has a single USB ports which is accessible via the onboard type A USB
connector.
Figure 1.1- V2DIP1 48
The VNC2 is the second of FTDI’s Vinculum family of Embedded dual USB host controller devices. The
VNC2 device provides USB Host interfacing capability for a variety of different USB device classes
including support for BOMS (bulk only mass storage), Printer, HID (human interface devices). For mass
storage devices such as USB Flash drives, VNC2 also transparently handles the FAT file structure.
Communication with non USB devices such as a low cost microcontroller is accomplished via either UART,
SPI or parallel FIFO interfaces. The VNC2 provides a new cost effective solution for providing USB Host
capability into products that previously did not have the hardware resources available.
The VNC2 supports the capability to enable customers to develop custom firmware using the Vinculum II
development software tool suite. The development tools support compiler, linker and debugger tools
complete within an integrated development environment (IDE).
The Vinculum-II VNC2 family of devices are available in Pb-free (RoHS compliant) 32-lead LQFP, 32-lead
QFN, 48-lead LQFP, 48-lead QFN, 64-Lead lQFP and 64-lead QFN packages.
Copyright © 2010 Future Technology Devices International Limited
1
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Table of Contents
1
Introduction............................................................................................ 1
2
Features ................................................................................................. 3
3
Pin Out and Signal Description ............................................................ 4
3.1
Module Pin Out .................................................................................................... 4
3.2
Pin Signal Description ........................................................................................ 6
3.3
I/O Configuration Using The Jumper Pin Header ............................................. 8
3.4
Default Interface I/O Pin Configuration .............................................................. 9
3.5
UART Interface................................................................................................... 10
Signal Description – UART Interface.............................................................................. 10
3.5.1
3.6
Serial Peripheral Interface (SPI) ....................................................................... 11
3.6.1
Signal Description - SPI Slave ........................................................................................ 11
3.6.2
Signal Description - SPI Master ...................................................................................... 11
3.7
Parallel FIFO Interface-Asynchronous Mode .................................................. 12
3.7.1
Signal Description - Parallel FIFO Interface ................................................................. 12
3.7.2
Timing Diagram – Asynchronous FIFO Mode Read and Write Cycle ..................... 13
3.8
Parallel FIFO Interface-Synchronous Mode .................................................... 14
3.8.1
3.9
Debugger Interface ............................................................................................ 16
3.9.1
4
5
Timing Diagram – Synchronous FIFO Mode Read and Write Cycle ....................... 14
Signal Description - Debugger Interface ...................................................................... 16
Firmware .............................................................................................. 17
4.1
Firmware Support .............................................................................................. 17
4.2
Available Firmware ............................................................................................ 17
4.3
Firmware Upgrades ........................................................................................... 17
External circuit Configuration ............................................................ 18
5.1
Adding a second USB Port ............................................................................... 18
6
Mechanical Dimensions ...................................................................... 19
7
Schematic Diagram ............................................................................. 20
8
Contact Information............................................................................. 21
Appendix A – References ............................................................................................ 22
Appendix B – List of Figures and Tables ................................................................... 23
List of Figures............................................................................................................... 23
List of Tables ................................................................................................................ 23
Appendix C – Revision History ................................................................................... 24
Copyright © 2010 Future Technology Devices International Limited
2
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
2
Features
The V2DIP1 48 incorporates the following features:
Uses FTDI’s VNC2-48Q embedded USB host
controller IC device
Auxiliary 3.3 V / 200 mA power output to
external logic.
Single USB ‘A’ type socket to interface with
USB peripheral devices
Power and traffic indicator LED’s
Connnection to a second USB interface port
available via module I/O pins if required.
V2DIP1-48 is a Pb-free, RoHS complaint
development module.
Jumper selectable UART, parallel FIFO or SPI
MCU interfaces
Debugger interface pin available via 6 way
male header which interfaces to separate
debugger module.
UART, parallel FIFO and SPI interfaces can be
programmed to a choice of available I/O pins
Firmware upgrades via UART or debugger
interface.
Single 5V supply input from DIL connectors or
5V supplied via USB VBUS slave interface or
debugger module.
FOC software development supported through
Vinculum software development tool suite IDe
consisting integrated compiler, linker, and
debugger capabilities.
All VNC2 signals available on 0.6” wide, 0.1”
pitch DIL male connectors.
Copyright © 2010 Future Technology Devices International Limited
3
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3
Pin Out and Signal Description
3.1 Module Pin Out
Figure 3.1 - V2DIP1 48 Module Pin Out (Top View)
Copyright © 2010 Future Technology Devices International Limited
4
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Figure 3.2 - V2DIP1 48 Module Pin Out (Bottom View)
Copyright © 2010 Future Technology Devices International Limited
5
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.2 Pin Signal Description
Pin No.
(VDIP1)
Name
(VDIP1)
Pin
Name
on PCB
J1-1
5V0
5V0
IOBUS5
IO5
Output
USB port 1 traffic activity indicator LED. This pin is hard wired to a
green LED on boardthe PCB. It is also brought out onto this pin which
allows for the possibility of bringing an additional LED traffic indicator
out of the V2DIP1 board. For example, if the V2DIP1 USB connector is
brought out onto an instrument front panel, an activity LED could be
mounted along side it.
J1-3
(3)
IOBUS6
IO6
Output
USB port 2 traffic activity indicator LED. This pin is hard wired to a
green LED on board the PCB. It is also brought out onto this pin which
allows for the possibility of bringing an additional LED traffic indicator
out of the V2DIP1 board. For example, if the V2DIP1 USB connector is
brought out onto an instrument front panel, an activity LED could be
mounted along side it.
J1-4
USBD1P
U1P
I/O
USB host / slave port 1 - USB Data Signal Plus with integrated pull up /
pull down resistor. Module has on board 27 Ω USB series resistor. This
pin can be brought out along with pin 5 to provide a second USB port, if
required
USBD1M
U1M
I/O
USB host / slave port 1 - USB Data Signal Minus with integrated pull up
/ pull down resistor. Module has on board 27 Ω USB series resistor. This
pin can be brought out along with pin 4 to provide a second USB port, if
required
IOBUS12
IO12
I/O
J1-7
GND
GND
PWR
(7)
J1-8
(8)
IOBUS13
IO13
I/O
5V safe bidirectional data / control bus bit 13
J1-9
IOBUS14
IO14
I/O
5V safe bidirectional data / control bus bit 14
J1-10
(10)
IOBUS15
IO15
I/O
5V safe bidirectional data / control bus bit 15
J1-11
IOBUS16
IO16
I/O
5V safe bidirectional data / control bus bit 16
IOBUS17
IO17
I/O
5V safe bidirectional data / control bus bit 17
J2-1
(24)
3V3
3V3
PWR
3.3V output from V2DIP1’s on board 3.3V L.D.O.
J2-2
PROG#
PROG#
Input
This pin is used in combination with the RESET# pin and the UART /
parallel FIFO / SPI interface to program firmware into the VNCL2.
RESET#
RST#
Input
Can be used by an external device to reset the VNCL2. This pin can be
used in combination with PROG# and the UART / parallel FIFO / SPI
interface to program firmware into the VNCL2.
IO25
I/O
(1)
J1-2
Type
PWR Input 5.0V module supply pin. This pin can be used to provide the 5.0V
input to the V2DIP1-48 when the V2DIP1-48 is not powered from the
USB connector (VBUS) or the debugger interface. Also connected to
DIL connector pins J1-2, J1-3 and J1-9 and J3-6.
(2)
(4)
J1-5
(5)
J1-6
Description
5V safe bidirectional data / control bus bit 12
(6)
Module ground supply pin
(9)
(11)
J1-12
(12)
(23)
J2-3
(22)
J2-4
(21)
IOBUS25
5V safe bidirectional data / control bus bit 25
Table 3.1 - Pin Signal Descriptions
Copyright © 2010 Future Technology Devices International Limited
6
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Pin No.
(VDIP1)
Name
Pin Name
(VDIP1)
on PCB
Type
Description
J2-5
(20)
IOBUS24
IO24
I/O
5V safe bidirectional data / control bus bit 24
J2-6
(19)
IOBUS23
IO24
I/O
5V safe bidirectional data / control bus bit 23
J2-7
GND
GND
PWR
Module ground supply pin
(18)
J2-8
IOBUS22
IO22
I/O
5V safe bidirectional data / control bus bit 22
I/O
5V safe bidirectional data / control bus bit 21
I/O
5V safe bidirectional data / control bus bit 20
I/O
5V safe bidirectional data / control bus bit 19
I/O
5V safe bidirectional data / control bus bit 18
(17)
J2-9
IOBUS21
IO21
(16)
J2-10
IOBUS20
IO20
(15)
J2-11
IOBUS19
IO19
(14)
J2-12
(13)
IOBUS18
IO18
Table 3.1 - Pin Signal Descriptions
Copyright © 2010 Future Technology Devices International Limited
7
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.3 I/O Configuration Using The Jumper Pin Header
Two three way jumper pin headers are provided to allow for simple configuration of the I/O on data and
control bus pins of the 48 pin QFN Vinculum-II. This is done by a combination of pulling up or pulling
down the 48 pin QFN Vinculum-II IOBUS25 (pin 46) and IOBUS26 (pin 47). The relevant portion of the
V2DIP1 48 module schematic is shown in Figure 3.3
IOBUS25
IOBUS26
Figure 3.3 - V2DIP1 48 On-Board Jumper Pin Configuration.
IOBUS25
(VNC2-48Q pin 47)
I/O Mode
IOBUS26
(VNC2-48Q pin 46)
Pull-Up
Pull-Up
Serial UART
Pull-Up
Pull-Down
SPI
Pull-Down
Pull-Up
Parallel FIFO
Pull-Down
Pull-Down
Serial UART
Table 3.2 - V2DIP1 48 Port Selection Jumper Pins
NOTE: This is only applicable when using VNC1L compatible firmware e.g. V2DAP2. Other wise the user
can set the pins for their own use.
Copyright © 2010 Future Technology Devices International Limited
8
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.4 Default Interface I/O Pin Configuration
The VNC2-48Q device is delivered without any firmware pre-loaded. As such the IOMUX will provide a
default pinout as shown in Table 3.3
Pin
No.
Name
Pin
Name
on
PCB
Data and Control Bus Configuration
Options
Type
UART
Interface
SPI Slave
Interface
SPI
Master
Interface
Parallel
FIFO
Interface
Debugger
Interface
J3-1
IOBUS0
IO0
I/O
NA
NA
NA
NA
debug_if
J1-2
IOBUS5
IO5
I/O
NA
spi_s0_mosi
NA
NA
NA
NA
spi_s0_miso
NA
NA
NA
uart_txd
NA
NA
NA
NA
J1-3
IOBUS6
IO6
I/O
J1-6
IOBUS12
IO12
I/O
J1-8
IOBUS13
IO13
I/O
uart_rxd
NA
NA
NA
NA
J1-9
IOBUS14
IO14
I/O
uart_rts#
NA
NA
NA
NA
J1-10
IOBUS15
IO15
I/O
uart_cts#
NA
NA
NA
NA
J1-11
IOBUS16
IO16
I/O
uart_dtr#
NA
NA
NA
NA
J1-12
IOBUS17
IO17
I/O
uart_dsr#
NA
NA
NA
NA
J2-12
IOBUS18
IO18
I/O
uart_dcd#
NA
NA
NA
NA
J2-11
IOBUS19
IO19
I/O
uart_ri#
NA
NA
NA
NA
J2-10
IOBUS20
IO20
I/O
NA
NA
NA
NA
uart_tx_acti
ve
Table 3.3 - Default Interface I/O Pin Configuration
Copyright © 2010 Future Technology Devices International Limited
9
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.5 UART Interface
When the data and control buses are configured in UART mode, the interface implements a standard
asynchronous serial UART port with flow control. The UART can support baud rates from 300baud to
3Mbaud. The UART interface is described more fully in a Vinculum-II datasheet please refer to:- FTDI
website.
3.5.1
Signal Description – UART Interface
The UART signals can be programmed to a choice of I/O pin available. Table 3.4 explains the available
pins for each of the UART signals.
Available Pins
Name
Type
Description
uart_txd
Output
Transmit asynchronous data output
J1-2, J1-8, J1-12, J2-9
uart_rxd#
Input
Receive asynchronous data input
J1-3, J1-9, J2-12, J2-8
uart_rts#
Output
Request To Send Control Output
J1-10, J2-11, J2-6
uart_cts#
Input
Clear To Send Control Input
J1-6, J1-11, J2-5, J2-10
uart_dtr#
Output
Data Acknowledge (Data Terminal
J1-6, J1-11, J2-5, J2-10
Ready Control) Output
J1-2, J1-8, J1-12, J2-9
uart_dsr#
Input
Data Request (Data Set Ready
Control) Input
J1-3, J1-9, J2-12, J2-8
J1-10, J2-11, J2-6
uart_dcd#
Input
uart_ri#
Input
Data Carrier Detect Control Input
Ring Indicator Control Input.
uart_ri# low can be used to resume
the PC USB Host controller from
suspend.
J1-6, J1-11, J2-5, J2-10
uart_tx_active
Output
Enable Transmit Data for RS485
designs. uart_tx_active may be used
to signal that a transmit operation is
in progress.The uart_tx_active signal
will be set high one bit-time before
data is transmitted and return low
one bit time after the last bit of a
data frame has been transmitted
Table 3.4 - Data and Control Bus Signal Mode Options – UART Interface
Copyright © 2010 Future Technology Devices International Limited
10
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.6 Serial Peripheral Interface (SPI)
The VNC2-48Q has one master module and two slave modules. These modules are described more fully in
a Vinculum-II datasheet please refer to:- FTDI website.
3.6.1 Signal Description - SPI Slave
The SPI Slave signals can be programmed to a choice of available I/O pins. Table 3.5 explains the
available pins for each of the SPI Slave signals.
Name
Type
Description
spi_s0_clk
Input
Slave clock input
Input/Output
Master Out Slave In
Available Pins
J1-6, J1-11, J2-5, J2-10
spi_s1_clk
J1-2, J1-8, J1-12, J2-9
spi_s0_mosi
spi_s1_mosi
J1-3, J1-9, J2-12, J2-8
spi_s0_miso
Synchronous data from master to
slave
Output
spi_s1_miso
J1-10, J2-11, J2-6
spi_s0_ss#
Master In Slave Out
Synchronous data from slave to
master
Input
Slave chip select
spi_s1_ss#
Table 3.5 - Data and Control Bus Signal Mode Options – SPI Slave
3.6.2 Signal Description - SPI Master
The SPI Master signals can be programmed to a choice of available I/O pins Table 3.6 shows the SPI
master signals and the available pins that they can be mapped.
Available Pins
Name
Type
Description
J1-6, J1-11, J2-5, J2-10
spi_m_clk
Output
SPI master clock input
J1-2, J1-8, J1-12, J2-9
spi_m_mosi
Output
Master Out Slave In
Synchronous data from master to
slave
J1-3, J1-9, J2-12, J2-8
spi_m_miso
Input
Master In Slave Out
Synchronous data from slave to
master
J1-10, J2-11, J2-6
spi_m_cs_0#
Output
Active low slave select 0 from master
to
slave 0
spi_m_cs_1#
J1-6, J1-11, J2-5, J2-10
Output
Active low slave select 1 from master
to
slave 1
Copyright © 2010 Future Technology Devices International Limited
11
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Table 3.6 - Data and Control Bus Signal Mode Options – SPI Master
3.7 Parallel FIFO Interface-Asynchronous Mode
The Parallel FIFO Asynchronous mode is functionally the same as the Parallel FIFO Interface present in
VDIP1 has an eight bit parallel data bus, individual read and write strobes and two hardware flow control
signals.
3.7.1 Signal Description - Parallel FIFO Interface
The Parallel FIFO Interface signals can be programmed to a choice of available I/O pins. Table 3.7
shows the Parallel FIFO Interface signals and the pins that they can be mapped.
Available Pins
J1-6, J1-11, J2-5, J2-10
J1-2, J1-8, J1-12, J2-9
Name
fifo_data[0]
Description
I/O
FIFO data bus Bit 0
I/O
FIFO data bus Bit 1
fifo_data[1]
J1-3, J1-9, J2-12, J2-8
fifo_data[2]
J1-10, J2-11, J2-6
fifo_data[3]
J1-6, J1-11, J2-5, J2-10
fifo_data[4]
J1-2, J1-8, J1-12, J2-9
Type
I/O
FIFO data bus Bit 2
I/O
FIFO data bus Bit 3
I/O
FIFO data bus Bit 4
I/O
FIFO data bus Bit 5
fifo_data[5]
J1-3, J1-9, J2-12, J2-8
fifo_data[6]
J1-10, J2-11, J2-6
fifo_data[7]
I/O
FIFO data bus Bit 6
I/O
FIFO data bus Bit 7
When high, do not read data from
J1-6, J1-11, J2-5, J2-10
fifo_rxf#
Output
the FIFO. When low, there is data
available in the FIFO which can be
read bystrobing RD# low, then high.
When high, do not write data into the
J1-2, J1-8, J1-12, J2-9
fifo_txe#
Output
FIFO. When low, data can be written
into the FIFO by strobing WR high,
then low.
Enables the current FIFO data byte
J1-3, J1-9, J2-12, J2-8
on D0...D7 when low. Fetches the
fifo_rd#
next FIFO data byte (if available)
Input
from the receive FIFO buffer when
RD# goes from high to low
Writes the data byte on the D0...D7
J1-10, J2-11, J2-6
fifo_wr#
Input
pins into the transmit FIFO buffer
when WR goes from high to low.
Table 3.7 - Data and Control Bus Signal Mode Options – Parallel FIFO Interface
Copyright © 2010 Future Technology Devices International Limited
12
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.7.2 Timing Diagram – Asynchronous FIFO Mode Read and Write Cycle
When in Asynchronous FIFO interface mode, the timing of a read and write operation on the FIFO
interface is shown in Figure 3.4 and Table 3.8
Figure 3.4 – Asynchronous FIFO Mode Read and Write Cycle.
Time
t1
Description
Min
Max
Unit
1
14
ns
100
-
ns
1
14
ns
30
-
ns
0
-
ns
1
14
ns
100
-
ns
5
-
ns
5
-
ns
30
-
ns
t11
WR# active after TXE#
0
Table 3.8 - Asynchronous FIFO Mode Read Cycle Timing
ns
RD# inactive to RXF#
t2
RXF# inactive after RD# cycle
t3
RD# to Data
t4
RD# active pulse width
t5
RD# active after RXF#
t6
WR# active to TXE# inactive
t7
TXE# inactive after WR# cycle
t8
DATA to TXE# active setup time
t9
DATA hold time after WR# inactive
t10
WR# active pulse width
In asynchronous mode an external device can control data transfer driving FIFO_WR# and FIFO_RD#
inputs. In contrast to synchronous mode, in asynchronous mode the 245 FIFO module generates the
output enable EN# signal. EN# signal is effectively the read signal RD#.
Current byte is available to be read when FIFO_RD# goes low. When FIFO_RD# goes high, FIFO_RXF#
output will also go high. It will only become low again when there is another byte to read.
When FIFO_WR# goes low FIFO_TXE# flag will always go high. FIFO_TXE# goes low again only when
there is still space for data to be written in to the module.
Copyright © 2010 Future Technology Devices International Limited
13
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.8 Parallel FIFO Interface-Synchronous Mode
The Parallel FIFO Synchronous mode has an eight bit data bus, individual read and write strobes, two
hardware flow control signals, an output enable and a clock out.
The synchronous FIFO mode uses the parallel FIFO interface signals detailed in Table 3.7 and an
additional two signals detailed in Table 3.9.
Available Pins
J2-8, J2-4, J1-7,
J2-13
J1-14, J1-19, J2-18,
J2-7, J1-4, J1-8, J1-16, J1-20, J2-17
Name
Type
Description
Output
FIFO Output Enable
fifo_oe#
fifo_clkout
Output
FIFO Output Enable
Table 3.9 - Data and Control Bus Signal Mode Options – Synchronous FIFO mode
3.8.1 Timing Diagram – Synchronous FIFO Mode Read and Write Cycle
When in Synchronous FIFO interface mode, the timing of a read and write operation on the FIFO interface
are shown in Figure 3.5 and Table 3.10
Figure 3.5 - Synchronous FIFO Mode Read and Write Cycle
Copyright © 2010 Future Technology Devices International Limited
14
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Time
t1
Description
CLKOUT period
Min
Typical
Max
Unit
-
20.83
-
ns
ns
t2
CLKOUT high period
9.38
10.42
11.46
t3
CLKOUT low period
9.38
10.42
11.46
ns
ns
t4
CLKOUT to RXF#
1
-
7.83
t5
CLKOUT to read DATA valid
1
-
7.83
ns
t6
OE# to read DATA valid
1
-
7.83
ns
t7
CLKOUT to OE#
1
-
7.83
ns
t8
RD# setup time
12
-
-
ns
t9
RD# hold time
0
-
-
ns
t10
CLKOUT TO TXE#
1
-
-
ns
t11
Write DATA setup time
12
-
-
ns
t12
Write DATA hold time
0
-
-
ns
t13
WR# setup time
12
-
-
ns
-
ns
t14
WR# hold time
0
Table 3.10 - Synchronous FIFO Mode Read and Write Cycle Timing
In synchronous mode data can be transmitted to and from the FIFO module on each clock edge. An
external device synchronises to the CLKOUT output and it also has access to the output enable OE# input
to control data flow. An external device should drive output enable OE# low before pulling RD# line
down.
When bursts of data are to be read from the module RD# should be kept low. RXF# remains low when
there is still data to be read. Similarly when bursts of data are to be written to the module WR# should
be kept low. TXE# remains low when there is still space available for the data to be written
Copyright © 2010 Future Technology Devices International Limited
15
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
3.9 Debugger Interface
The purpose of the debugger interface is to provide access to the VNC2 silicon/firmware debugger. The
debug interface can be accessed by connecting a debug module to the J3 connector. This debug module
will give access to the debugger through a USB connection to a PC via the Integrated Development
Environment (IDE). The IDE is a graphical interface to the VNC2 software development tool-chain and
gives the following debug capabilities through the debugger interface:
Flash Erase, Write and Program.
Application debug - application code can have breakpoints, be single stepped and can be halted.
Detailed internal debug - memory and register read/write access.
The Debugger Interface, and how to use it, is further described in the following applications Note
Vinculum-II Debug Interface Description
3.9.1 Signal Description - Debugger Interface
Table 3.11 shows the signals and pins description for the debugger interface pin header J3
Name
Pin No.
Name
On PCB
Type
Description
J3-1
IO0
DBG
I/O
Debugger Interface
J3-2
-
[Key]
-
Not connected. Used to make sure that the
debug module is connected correctly.
J3-3
GND
GND
PWR
Module ground supply pin
Input
J3-4
RESET#
RST#
J3-5
PROG#
PRG#
J3-6
5V0
VCC
Input
Can be used by an external device to reset
the VNCL2. This pin is also used in
combination with PROG# and the UART
interface to program firmware into the
VNC2.
This pin is used in combination with the
RESET# pin and the UART interface to
program firmware into the VNC2.
PWR Input
5.0V module supply pin. This pin can be
used to provide the 5.0V input to the
V2DIP1-48 when the V2DIP1-48 is not
powered from the USB connector (VBUS)
or the debugger interface. Also connected
to DIL connector pins J1-2, J1-3 and J1-9
and J3-6.
Table 3.11 - Signal Name and Description – Debugger Interface
Copyright © 2010 Future Technology Devices International Limited
16
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
4
Firmware
4.1 Firmware Support
V2DIP1-48 can be programmed with the customers own firmware or with pre-compiled firmware profiles
to allow a designer to easily change the functionality of the chip.
4.2 Available Firmware
V2DAP firmware is currently available: USB Host for single Flash Disk and general purpose USB
peripherals. Selectable UART, FIFO or SPI interface command monitor. please refer to:- FTDI website for
full details.
4.3 Firmware Upgrades
Refer to the debugger interface section which can be used to update the firmware.
Copyright © 2010 Future Technology Devices International Limited
17
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
5
External circuit Configuration
5.1 Adding a second USB Port
The external circuit configuration for adding second USB host port, with the USB activity LED,
is shown below in Figure 5.1
Figure 5.1 Additional USB Port Configuration
Copyright © 2010 Future Technology Devices International Limited
18
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
6
Mechanical Dimensions
15.61
9.89
7.89
J1
15.48
XX FTD
F
VNXX XX TD I
VN C2XX XX I
C - X X
YY2- 48QXX X
YY W32Q 1AX
W W 1A
W
17.78
JP2
JP1
J2
J3
50.45
1.27
3.02
13.97
3.89
2.38
CN1
41.91
43.18
4.90
1.60
17.85
8.65
7.00
Figure 6.1 V2DIP1 48 Dimensions (Top View)
2.54
Figure 6.2 V2DIP1 48 Dimensions (Side View)
Tolerance is ±0.2mm
All dimensions are in mm
Copyright © 2010 Future Technology Devices International Limited
19
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
7
Schematic Diagram
Figure 7.1 - Schematic Diagram
Copyright © 2010 Future Technology Devices International Limited
20
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
8
Contact Information
Head Office – Glasgow, UK
Future Technology Devices International Limited
Unit 1, 2 Seaward Place,
Centurion Business Park
Glasgow, G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
E-mail (Sales)
[email protected]
E-mail (Support) [email protected]
E-mail (General Enquiries) [email protected]
Web Site URL
http://www.ftdichip.com
Web Shop URL
http://www.ftdichip.com
Branch Office – Taipei, Taiwan
Future Technology Devices International Limited (Taiwan)
2F, No 516, Sec. 1 NeiHu Road
Taipei 114
Taiwan, R.O.C.
Tel: +886 (0) 2 8791 3570
Fax: +886 (0) 2 8791 3576
E-mail (Sales)
[email protected]
E-mail (Support) [email protected]
E-mail (General Enquiries) [email protected]
Web Site URL
http://www.ftdichip.com
Branch Office – Hillsboro, Oregon, USA
Future Technology Devices International Limited (USA)
7235 NW Evergreen Parkway, Suite 600
Hillsboro, OR 97123-5803
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-Mail (Sales)
E-Mail (Support)
Web Site URL
[email protected]
[email protected]
http://www.ftdichip.com
Branch Office – Shanghai, China
Future Technology Devices International Limited (China)
Room 408, 317 Xianxia Road,
ChangNing District,
ShangHai, China
Tel: +86 (21) 62351596
Fax: +86(21) 62351595
E-Mail (Sales): [email protected]
E-Mail (Support): [email protected]
E-Mail (General Enquiries): [email protected]
Web Site URL
http://www.ftdichip.com
Distributor and Sales Representatives
Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales
representative(s) in your country.
Copyright © 2010 Future Technology Devices International Limited
21
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Appendix A – References
Application and Technical Notes
Vinculum-II IO Cell Description
Vinculum-II Debug Interface Description
Vinculum-II IO Mux Explained
Vinculum-II PWM Example
Migrating Vinculum Designs From VNC1L to VNC2-48L1A
Vinculum-II Errata Technical Note
Copyright © 2010 Future Technology Devices International Limited
22
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Appendix B – List of Figures and Tables
List of Figures
Figure 1.1- V2DIP1 48 ................................................................................................................... 1
Figure 3.1 - V2DIP1 48 Module Pin Out (Top View) .......................................................................... 4
Figure 3.2 - V2DIP1 48 Module Pin Out (Bottom View) .................................................................... 5
Figure 3.3 - V2DIP1 48 On-Board Jumper Pin Configuration. .............................................................. 8
Figure 3.4 – Asynchronous FIFO Mode Read and Write Cycle. ........................................................... 13
Figure 3.5 - Synchronous FIFO Mode Read and Write Cycle .............................................................. 14
Figure 5.1 Additional USB Port Configuration .................................................................................. 18
Figure 6.1 V2DIP1 48 Dimensions (Top View) ................................................................................ 19
Figure 6.2 V2DIP1 48 Dimensions (Side View) ............................................................................... 19
Figure 7.1 - Schematic Diagram ................................................................................................... 20
List of Tables
Table 3.1 - Pin Signal Descriptions .................................................................................................. 6
Table 3.2 - V2DIP1 48 Port Selection Jumper Pins ............................................................................. 8
Table 3.3 - Default Interface I/O Pin Configuration ........................................................................... 9
Table 3.4 - Data and Control Bus Signal Mode Options – UART Interface ........................................... 10
Table 3.5 - Data and Control Bus Signal Mode Options – SPI Slave ................................................... 11
Table 3.6 - Data and Control Bus Signal Mode Options – SPI Master ................................................. 12
Table 3.7 - Data and Control Bus Signal Mode Options – Parallel FIFO Interface ................................. 12
Table 3.8 - Asynchronous FIFO Mode Read Cycle Timing .................................................................. 13
Table 3.9 - Data and Control Bus Signal Mode Options – Synchronous FIFO mode .............................. 14
Table 3.10 - Synchronous FIFO Mode Read and Write Cycle Timing ................................................... 15
Table 3.11 - Signal Name and Description – Debugger Interface ....................................................... 16
Copyright © 2010 Future Technology Devices International Limited
23
Document Reference No.: FT_000236
V2DIP1-48 VNC2-48 Development Module Datasheet Version 1.01
Clearance No.: FTDI# 153
`
Appendix C – Revision History
Version 1.0
First Release
16th April 2010
Version 1.01
Added module’s images, edited mechanical drawings and
24th May 2010
Figure 5.1
Copyright © 2010 Future Technology Devices International Limited
24