26 09 13 ELECTRIC POWER MONITORING 9510-RTU

SECTION [26 09 13] [16290]
ELECTRICAL POWER MONITORING AND CONTROL
PART 1 - GENERAL
1.1
SCOPE
A.
1.2
This section defines the low voltage Central display and Data recorder for use in AC systems,
rated 600 V or less.
RELATED DOCUMENTS
A.
Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.
B.
[Related Sections (where applicable) include the following:
1.
Section [26 24 13] [16290] - Switchboards]
1.3
SUBMITTALS
A.
Submit shop drawings and product data for approval and final documentation in the quantities
listed according to the Conditions of the Contract. Customer name, customer location and
customer order number shall identify all transmittals.
B.
[Final Documents: Record documentation to include wiring diagrams, instruction and
installation manuals [and certified test reports.] ]
1.4
RELATED STANDARDS
A.
1.5
Meet the following recognized standards for application in hardened environments
1.
Device must meet all international standards for Safety & Construction applicable to this
type of device:
2.
UL3111-1
3.
CSA C22.2 No 1010-1
4.
Device must meet all international standards for Electromagnetic Immunity applicable to
this type of device:
5.
IEEE C.37-90.1-1989 IEEE Standard Surge Withstand Capability (SWC) Tests for
Protective Relays and Relay Systems (ANSI) (All inputs except for the network
communication port)
6.
ANSI C62.41 Surge Immunity
7.
Device must meet all international standards for Electromagnetic Emissions
8.
FCC Part 15 Subpart B, Class A Class A Digital Device, Radiated Emissions
QUALITY ASSURANCE
A.
Manufacturer Qualifications: Manufacturer of this equipment shall have a minimum of 5 years
experience producing similar electrical equipment.
B.
Comply with requirements of latest revisions of applicable industry standards.
1.6
DELIVERY, STORAGE AND HANDLING
A.
Store and handle in strict compliance with manufacturer’s instructions and recommendations.
Protect from potential damage from weather and construction operations. If the data recorders
are installed in equipment, store the equipment so condensation will not form on or in it. If
necessary, apply temporary heat where required to obtain suitable service conditions.
July 2, 2016
Power Monitoring & Control
[Project Name]
[26 09 13] [16290]-1
PART 2 - PRODUCTS
2.1
MANUFACTURERS
A.
2.2
[The low voltage power data recorder shall be type 9510-RTU by Siemens Industry Inc, or
pre-approved equal. Approved manufacturers are as follows:
1.
Siemens (ACCESS)
2.
. ]
COMPONENTS
A.
9510-RTU Advanced Data Recorder (ADR)
1.
Provide an Advanced Data Recorder with non-volatile memory, high-speed discrete
inputs, varied input/output options, multiple protocols, GPS capability, built-in Web server
technology, built-in email capability, optional display and logic capability meeting the
requirements set forth in this specification. Note any exceptions taken with a detailed
description.
a.
Advanced Data Recorder shall be Siemens Type 9510-RTU Advanced Data
Recorder with options and features described in this section.
2.
Basic hardware requirements of the Advanced Data Recorder are as follows:
a.
Power supply: The device shall accept power from 85-240 VAC (+/-10%), 47 to 63
Hz or 110-330 VDC (+/-10%) without external converters or separate ordering
options. Maximum burden shall be 20 VA. Ride-through shall be a minimum of
100ms (6 cycles @ 60Hz) for 96 VAC, or 200ms (12 cycles @ 60 Hz) for 120 VAC
or 800ms (48 cycles @ 60 Hz) for 240 VAC. Dielectric withstand shall be 2300
VAC rms, 60 Hz for 1 minute.
b.
On-board I/O: The device supplied shall have the following built-in I/O for this
project.
1.)
Three (3) Form C dry contact relays rated for switching of 2500 VA resistive
2.)
Four (4) Form A solid state outputs
3.)
8 Digital high-speed 1ms inputs (S1 to S8, SCOM), self-excited dry contact
sensing, no external voltage required, +30VDC differential between SCOM
and S1 through S8 inputs
c.
Communications
1.)
Provide the following built-in ports in the purchased configuration. All
communication ports shall be standard technology, as defined by the IEEE.
No communication interfaces not defined by the IEEE shall be accepted.
a.)
Standard communications card: includes RS-232/RS-485 (COM1),
RS-485 (COM2), programmable for baud rates from 1200 to 115200
bits per second.
b.)
An IrDA optical port at the face of the Advanced Data Recorder
display for quick downloading of Advanced Data Recorder information
with the IrDA port on a laptop.
2.)
Advanced Data Recorder must have the ability to upgrade communications
in the field to the following built-in port options:
a.)
10/100baseT Ethernet connection – with dual master functionality.
b.)
100baseFX Ethernet option– with dual master functionality.
c.)
33.6kbps Modem
3.)
All communication ports in this section must support all of the following
communication capabilities, independently configurable.
a.)
SEAbus/ION protocol
b.)
Modbus RTU protocol
c.)
Modbus TCP/IP
d.)
XML
e.)
DNP 3.0 protocol –serial and Ethernet
July 2, 2016
Power Monitoring & Control
[Project Name]
[26 09 13] [16290]-2
f.)
g.)
h.)
i.)
j.)
k.)
d.
e.
3.
Independent communications from each port simultaneously with no
noticeable interruption of communications from any of the other
communication ports
Protocols must be field configurable from the front display or via
communications ports. This must be capable of being accomplished
without resetting the Advanced Data Recorder, or interrupting its
operations in any way.
Modem and Ethernet port options must support simultaneous
communication to the Advanced Data Recorder in question and
gateway capability to other RS485 devices on the network via the
Advanced Data Recorder's RS485 ports.
Support upgrade of the instrumentation firmware.
Support time synchronization broadcast messages from a host
computer system
Support time synchronization to GPS time signal
1/4 VGA, bright graphical FSTN LCD display (320x240 pixel resolution)
1.)
Ability to display Advanced Data Recorder data in multiple intuitive formats
at the Advanced Data Recorder display, with a minimum of the following
types of screens.
a.)
3 lines of 1/2" characters for easy viewing of critical power information
b.)
20 real time values on one display for summary overview of readings.
c.)
Display recent events written to the devices event log, including
diagnostic events
d.)
Display information from any parameter as a trend including
magnitude and time.
The device shall include [5 MB (standard)] or [10MB (optional)] of memory
(NVRAM) to store the following:
1.)
All setup data.
2.)
A time-stamped event log supporting at least 1000 events with 1ms
resolution shall record the following information about each event:
a.)
Time of event
b.)
Cause of event
c.)
Effect of event
d.)
Device output reactions
e.)
Priority of event
3.)
Min/Max data for all monitored parameters
4.)
Fifty (50) Data Recorder Modules that can each store up to 16 channels of
historical trend data with the following features:
a.)
Each data recorder shall be able to record any high speed (½-cycle)
or high accuracy (1-second) parameter, either measured or derived.
b.)
Each data recorder shall be enabled and triggered manually or
through internal operating conditions, including periodic timer or set
point activity.
c.)
The number of records (depth) of each data recorder and the
overflow conditions (stop-when-full or circular) shall be
programmable.
The device shall have Modbus Master Capability. This will allow other Modbus RTU slave
devices (such as the Siemens PAC3200/3100 power meters, Siemens WL/VL breakers,
additional Modbus RTU hardware, PLC’s, etc.) to tie into the device. The device shall
then be able to display, trend and alarm the Modbus slave device data locally on the
built-in display.
July 2, 2016
Power Monitoring & Control
[Project Name]
[26 09 13] [16290]-3
4.
5.
6.
7.
8.
9.
10.
When equipped with an Ethernet port the ADR shall include:
a.
[email protected]®: Automatically e-mail alarm notifications or scheduled system status
updates. E-mail messages sent by the devices can be received like any ordinary
e-mail message. Data logs can also be sent on an event-driven or scheduled
basis.
b.
WebMeter™: Standard built in web pages in the device enable access to real-time
values and basic power quality information using a standard web browser. Basic
configuration of the device can also be performed through the browser. Web pages
must be configurable to allow custom HTML pages to be created. Device must
also support display of downstream devices from the web browser, i.e. feeders and
trip units on customizable web pages within the meter.
c.
XML compatible: Supports easy integration with custom reporting, spreadsheet,
database and other applications.
The device shall accommodate high speed Modbus TCP communications when
connected to Ethernet Port 502.
The device shall support Modbus Master Capability to request data from Modbus RTU
compatible slave devices, and make the data available for display on the front panel,
logging, alarming, for calculations etc.
The device shall provide a User Interface with features as follows:
a.
The device shall be capable of calculating the following information for any reading
at 1-second intervals:
1.)
Minimum value for any measured parameter.
2.)
Maximum value for any measured parameter.
3.)
Derived values for any combination of measured or calculated parameter,
using the following arithmetic, trigonometric and logic functions (equivalent
PLC capabilities):
a.)
Arithmetic functions: division, multiplication, addition, subtraction,
power, absolute value, square root, average, max, min, RMS, sum,
sum-of-squares, unary minus, integer ceiling, integer floor, modulus,
exponent, PI
b.)
Trigonometric functions: COS, SIN, TAN, ARCCOS, ARCSIN,
ARCTAN, LN, LOG10
c.)
Logic functions: =, =>, <=, <>, <, > and, OR, NOT, IF
d.)
Thermocouple linearization functions: Type J, Type K, Type R, Type
RTD, Type T
e.)
Temperature conversion functions: C to F, F to C
The device shall have the ability to provide up to 20 customizable HTML web pages built
into the devices as standard. These shall be viewable from any internet explorer web
browser.
The device shall have the ability to send multiple Emails directly from the device for
alarms or based on an event.
The device shall provide a User Interface with features as follows:
a.
The device shall support direct display of all parameters on the front panel in user
programmable groups, using plain language labels. Simultaneous access to all
parameters shall be available through any communication port.
b.
The device shall be field programmable as follows:
1.)
Basic parameters: auxiliary input and output scales and communications
setup.
2.)
All basic parameters described above, plus additional set point/relay and
data log setup parameters may be programmed via the communications
port using a portable or remotely located computer terminal.
3.)
The priority of set point events shall be programmable.
4.)
Using ION modules, support customized configurations of all operating
parameters.
July 2, 2016
Power Monitoring & Control
[Project Name]
[26 09 13] [16290]-4
5.)
6.)
Provisions shall be made to ensure that programming through a computer
can be secured by user ID and password.
Provisions shall be made to ensure that programming through the front
panel is secured by password.
PART 3 - EXECUTION
3.1
INSTALLATION
A.
The Contractor shall furnish, install and terminate all communication conductors and associated
conduits external to any factory supplied equipment.
B.
All communication conductor wiring and routing shall
recommendations and as shown on the contract drawings.
3.2
be
per
the
manufacturer's
ADJUSTMENTS AND CLEANING
A.
3.3
Clean exposed surfaces using manufacturer recommended materials and methods.
TESTING
A.
3.4
The following standard factory procedures and tests shall be performed on the equipment
provided under this section.
WARRANTY
A.
Equipment manufacturer warrants that all goods supplied are free of non-conformities in
workmanship and materials for one year from date of initial operation, but not more than
eighteen months from date of shipment.
END OF SECTION
July 2, 2016
Power Monitoring & Control
[Project Name]
[26 09 13] [16290]-5
Similar pages