CY8CKIT-035 Power Supervision Expansion Board Kit (EBK) Quick Start Guide.pdf

EXPANSION BOARD KIT QUICK START GUIDE
CY8CKIT-035 PSOC® POWER SUPERVISION
EXPANSION BOARD KIT QUICK START GUIDE
CY8CKIT-035 PSOC® POWER SUPERVISION
EXPANSION BOARD KIT QUICK START GUIDE
CY8CKIT-035 PSOC® POWER SUPERVISION
Quick Start Guide
DC Power Adapter 12V/2A
I2C/SMBus/PMBus Port 5-Pin Header
V1 = 5 V Rail
Power Jack
(12V Power Rail)
V2 = 3.3 V Rail
(5 V to 3.3 V LDO)
2X20
Pin Header
V3 = 2.5 V Rail
(5 V to 2.5 V LDO)
V4 = 1.8 V
(5 V to 1.8 V LDO)
Potentiometer / Simulated Load
PSOC 1
®
8-bit M8C
For PSoC 1 power supervision,
use this kit with PSoC Kit
(CY8CKIT-001).
See page-2 of this Quick Start
Guide for instructions.
PSOC 3
®
8-bit 8051
For PSoC 3 power supervision,
use this kit with PSoC 3 Kit
(CY8CKIT-030) or
PSoC Kit (CY8CKIT-001).
PSOC 5LP
®
32-bit Cortex M3
For PSoC 5LP power supervision,
use this kit with PSoC 5LP Kit
(CY8CKIT-050) or
PSoC Kit (CY8CKIT-001).
See page-3 of this Quick Start
Guide for instructions to use with
PSoC 3 Kit.
See page-4 of this Quick Start
Guide for instructions to use with
PSoC 5LP Kit.
Refer the PSoC 3/PSoC 5LP
Power Supervision Kit Guide for
instructions to use with PSoC Kit.
Power Supervision Kit Guide for
instructions to use with PSoC Kit.
Refer the PSoC 3/PSoC 5LP
Quick Start Guide
DC Power Adapter 12V/2A
I2C/SMBus/PMBus Port 5-Pin Header
V1 = 5 V Rail
Power Jack
(12V Power Rail)
V2 = 3.3 V Rail
(5 V to 3.3 V LDO)
2X20
Pin Header
V3 = 2.5 V Rail
(5 V to 2.5 V LDO)
V4 = 1.8 V
(5 V to 1.8 V LDO)
Potentiometer / Simulated Load
PSOC 1
PSOC 3
PSOC 5LP
For PSoC 1 power supervision,
use this kit with PSoC Kit
(CY8CKIT-001).
For PSoC 3 power supervision,
use this kit with PSoC 3 Kit
(CY8CKIT-030) or
PSoC Kit (CY8CKIT-001).
For PSoC 5LP power supervision,
use this kit with PSoC 5LP Kit
(CY8CKIT-050) or
PSoC Kit (CY8CKIT-001).
See page-3 of this Quick Start
Guide for instructions to use with
PSoC 3 Kit.
See page-4 of this Quick Start
Guide for instructions to use with
PSoC 5LP Kit.
®
8-bit M8C
See page-2 of this Quick Start
Guide for instructions.
®
8-bit 8051
Refer the PSoC 3/PSoC 5LP
Power Supervision Kit Guide for
instructions to use with PSoC Kit.
®
32-bit Cortex M3
Refer the PSoC 3/PSoC 5LP
Power Supervision Kit Guide for
instructions to use with PSoC Kit.
Quick Start Guide
DC Power Adapter 12V/2A
I2C/SMBus/PMBus Port 5-Pin Header
V1 = 5 V Rail
Power Jack
(12V Power Rail)
V2 = 3.3 V Rail
(5 V to 3.3 V LDO)
2X20
Pin Header
V3 = 2.5 V Rail
(5 V to 2.5 V LDO)
V4 = 1.8 V
(5 V to 1.8 V LDO)
Potentiometer / Simulated Load
PSOC 1
PSOC 3
PSOC 5LP
For PSoC 1 power supervision,
use this kit with PSoC Kit
(CY8CKIT-001).
For PSoC 3 power supervision,
use this kit with PSoC 3 Kit
(CY8CKIT-030) or
PSoC Kit (CY8CKIT-001).
For PSoC 5LP power supervision,
use this kit with PSoC 5LP Kit
(CY8CKIT-050) or
PSoC Kit (CY8CKIT-001).
See page-3 of this Quick Start
Guide for instructions to use with
PSoC 3 Kit.
See page-4 of this Quick Start
Guide for instructions to use with
PSoC 5LP Kit.
®
8-bit M8C
See page-2 of this Quick Start
Guide for instructions.
®
8-bit 8051
Refer the PSoC 3/PSoC 5LP
Power Supervision Kit Guide for
instructions to use with PSoC Kit.
®
32-bit Cortex M3
Refer the PSoC 3/PSoC 5LP
Power Supervision Kit Guide for
instructions to use with PSoC Kit.
EXPANSION BOARD KIT QUICK START GUIDE
PSOC 1 POWER SUPERVISION USING
POWER SUPERVISION KIT (CY8CKIT-035) AND PSOC KIT (CY8CKIT-001)
1
• Download and install the PSoC Power Supervision Kit
software from www.cypress.com/go/CY8CKIT-015
2
• On the PSoC Kit (CY8CKIT-001), set VDD to 5V using
SW3, set J8 to VREG, set J7 and J6 to VDD. Attach the
LCD to CY8CKIT-001 and set jumper J12 to ON.
All other jumpers are ‘don’t care’
3
• Connect SW1 to P1_7 and SW2 to P2_7 on the
CY8CKIT-001
• Connect the CY8C28 family processor module
to CY8CKIT-001
4
• On the Power Supervision Kit (CY8CKIT-035) set
jumpers as follows: Insert J5 in position 2-3 and
populate J6, J7, J8, J9, J10, J11, J12, and J13
5
• Connect Miniprog3 to the CY8C28 processor module
• Launch PSoC Programmer; load
CY8CKIT_015_Example_Project.hex, located at
C:\Program Files (x86)\Cypress\PSoC 1 Power
Supervision Kit\1.0\Firmware\Hex_File
• In PSoC Programmer, set Programming Mode – Reset;
Auto Detection – ON; Protocol – ISSP; Voltage – 5.0
• Power the CY8CKIT-001 and click on Program
6
•
•
•
•
•
After programming, disconnect the Miniprog3
Disconnect power from CY8CKIT-001
Connect the CY8CKIT-035 into Port A of CY8CKIT-001
Connect power to CY8CKIT-001
The LCD displays four rail voltages in mV. Pressing SW1
displays four rail currents in 0.1mA
• For more details, see Example Project section in the
PSoC 1 Power Supervision Kit Guide
EXPANSION BOARD KIT QUICK START GUIDE
PSOC 3 POWER SUPERVISION USING
POWER SUPERVISION KIT (CY8CKIT-035) AND PSOC 3 KIT (CY8CKIT-030)
2
1
• Download and install the PSoC Power Supervision Kit
software from www.cypress.com/go/CY8CKIT-035
• On the PSoC 3 Kit (CY8CKIT-030) set VDDD and VADJ
to 5V using J10 and J11 jumpers
• All other jumpers should be in specified default settings
CAUTION: DO NOT
connect the CY8CKIT-035
board at this step. Follow
instruction in Step 4
3
• Connect the USB cable to J1 of CY8CKIT-030
• Launch PSoC Programmer, set Programming Mode: Reset;
Auto Detection: ON
• Load and program file Power_Demo-030_rev3.hex,
located at <Install_Directory>\CY8CKIT-035 EBK\
<version>\Firmware\Hex_Files
4
• Disconnect the USB cable from CY8CKIT-030
• Ensure the LCD module included with CY8CKIT-030
is mounted
• Connect the Power Supervision Kit (CY8CKIT-035)
Expansion Board to Port E of CY8CKIT-030
3
6
5
2
1
5
• On the CY8CKIT-035, insert jumper J5 in position 1-2
and populate J6, J7, J8, J9, J10, J11, J12 and J13
• Connect the 12V/2A power supply to J3 of CY8CKIT-035
• Connect the MiniProg3 to the white connector (J2) of
CY8CKIT-035
4
1
6
• Close PSoC Programmer; launch PSoC Power Supervision
Tool. It will automatically connect to the MiniProg3 1
• Click Read All to load configuration 2
• Click PMBus Console tab 3 ; Click Start Monitor 4
• The tool shows voltage and current of the rails 5
• Click command buttons to control them 6
EXPANSION BOARD KIT QUICK START GUIDE
PSOC 5LP POWER SUPERVISION USING
POWER SUPERVISION KIT (CY8CKIT-035) AND PSOC 5LP KIT (CY8CKIT-050)
1
• Download and install the PSoC Power Supervision Kit
software from www.cypress.com/go/CY8CKIT-035
2
• On the PSoC 5LP Kit (CY8CKIT-050) set jumpers J10, J11
in position 2-3. Disconnect J43, J44. All other jumpers
should be in kit default settings
CAUTION: DO NOT
connect the CY8CKIT-035
board at this step. Follow
instruction in Step 4
3
• Connect the USB cable to J1 of CY8CKIT-050
• Launch PSoC Programmer, set Programming Mode: Reset;
Auto Detection: ON
• Load and program file Power_Demo-050_rev3.hex,
located at <Install_Directory>\CY8CKIT-035 EBK\
<version>\Firmware\Hex_Files
4
• Disconnect the USB cable from CY8CKIT-050
• Ensure the LCD module included with CY8CKIT-050
is mounted
• Connect the Power Supervision Kit (CY8CKIT-035)
Expansion Board to Port E of CY8CKIT-050
3
6
5
2
1
5
• On the CY8CKIT-035, insert jumper J5 in position 1-2
and populate J6, J7, J8, J9, J10, J11, J12 and J13.
• Connect the 12V/2A power supply to J3 of CY8CKIT-035
• Connect the MiniProg3 to the white connector (J2) of
CY8CKIT-035
4
1
6
• Close PSoC Programmer; launch PSoC Power Supervision
Tool. It will automatically connect to the MiniProg3 1
• Click Read All to load configuration 2
• Click PMBus Console tab 3 ; Click Start Monitor 4
• The tool shows voltage and current of the rails 5
• Click command buttons to control them 6
© 2015 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the properties of their respective owners.
001-95029 Rev.*A
Similar pages