AN-876: Replacing Nationals LM75 with the Analog Devices, Inc. ADT75 (Rev. 0) PDF

AN-876
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
AN-876 Replacing National’s LM75 with the Analog Devices, Inc. ADT75
by Donal McNamara
INTRODUCTION
The ADT75 has two grades, the ADT75A and the ADT75B.
The ADT75B is a higher temperature accurate part, and the
ADT75A is designed as a second source for the LM75.
The ADT75 is a functional and pin- and package-compatible
replacement for the LM75. No software or hardware change
is required when replacing the LM75 with the ADT75.
TEMPERATURE ERROR PERFORMANCE OVER
TEMPERATURE
The performance capabilities of the ADT75A grade and LM75
over temperature are completely compatible. Both parts have
similar performance graphs (see Figure 3).
Note that if more accuracy is required, the ADT75B grade is
recommended.
1.0
OS/ALERT 3
TOP VIEW
GND 4 (Not to Scale)
8
VDD
0.8
7
A0
0.6
6
A1
5
A2
Figure 1. ADT75 Pin Configuration
8
+VS
SCL 2
7
A0
O.S. 3
6
A1
GND 4
5
A2
VDD = 3.3V
0.2
VDD = 5V
0
–0.2
–0.4
–0.6
06439-002
SDA 1
0.4
–0.8
–1.0
–55
Figure 2. LM75 Pin Configuration
–35
–15
5
25
45
65
85
105
125
TEMPERATURE (°C)
06439-003
ADT75
TEMPERATURE ERROR (°C)
SCL 2
06439-001
SDA 1
Figure 3. ADT75 and LM75—Typical Temperature Accuracy
COMPATIBILITY
Table 1. Feature Comparison of the ADT75 and the LM75
Feature
I2C Interface
I²C Bus Address
8-Lead MSOP and 8-Lead SOIC
Identical Register Addresses1
Identical Register Content
Identical Temperature Accuracy
9-Bit Resolution
3.3 V and 5 V Operation
Similar AC/DC Parameters
Identical OS and Configuration Functions
Twos Complement Coding
1
ADT75A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
LM75
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
The ADT75 and the LM75 have identical register content. The ADT75 contains additional register bits for one shot mode, SMBus alert enable, and extra temperature
resolution bits. The contents of all these additional registers can be ignored without having to modify LM75 software.
Rev. 0 | Page 1 of 4
AN-876
OVERTEMPERATURE MODES
•
The ADT75 powers up in default as an OS pin. The LM75
also powers up in default as an OS pin.
•
The comparator mode is the default overtemperature
power-up mode for both the ADT75 and the LM75.
•
Both parts can be programmed to have the OS pin be
either active low or active high. Both parts follow the
interrupt response shown in Figure 4.
Note that there is an additional feature on the ADT75 that is not
available on the LM75. This is the SMBus alert function. If the
user chooses to employ this feature on the ADT75, Bit 7 of the
configuration register must be set to enable.
TEMPERATURE
82°C
81°C
TOS
80°C
79°C
78°C
77°C
76°C
THYST
75°C
74°C
73°C
OS/ALERT PIN
(COMPARATOR MODE)
POLARITY = ACTIVE LOW
OS/ALERT PIN
(INTERRUPT MODE)
POLARITY = ACTIVE LOW
OS/ALERT PIN
(COMPARATOR MODE)
POLARITY = ACTIVE HIGH
OS/ALERT PIN
(INTERRUPT MODE)
POLARITY = ACTIVE HIGH
TIME
WRITE TO
0x04 REG. 2
READ1
WRITE TO
0x04 REG. 2
READ1
WRITE TO
0x04 REG. 2
1READ FROM ANY REGISTER.
2THERE IS A 60ms DELAY BETWEEN WRITING TO THE
ONE-SHOT REGISTER AND THE OS/ALERT PIN GOING
ACTIVE. THIS IS DUE TO THE CONVERSION TIME.
Figure 4. OS/ALERT Output Temperature Response Diagram
Rev. 0 | Page 2 of 4
06439-004
READ1
AN-876
DIFFERENCES BETWEEN THE ADT75 AND THE LM75
The ADT75 has two grades, the ADT75A and the ADT75B. The ADT75B is a higher temperature-accurate part. The ADT75A is designed
as a second source for the LM75. There are small differences between the ADT75A and the LM75 that do not affect the capability of
either part being used in the same socket. The ADT75A differences are an enhancement on the LM75 and are listed in Table 2.
Table 2. Differences Between the ADT75A and the LM75
Feature
VDD
Data Sheet Specifications at VDD
Temperature Range
Temperature Accuracy
Resolution (Bits)
Temperature Conversion Time
(Maximum)
Supply Current (I2C Inactive)
LM75
Conditions
3.3 V only and 5 V
only
3.3 V and 5 V
−55°C to +125°C
TA = −55°C to +125°C ±3°C maximum
Comments
ADT75A
Conditions
3.0 V to 5.5 V
Comments
TA = +100°C to +125°C
8, 9
100 ms
LM75B @ 3.3 V and 5 V
LM75C @ 3.3 V and 5 V
Shutdown Current (3.3 V)
Shutdown Current (5 V)
One-Shot Register
Not present on LM75
500 μA
1 mA
4 μA typical
6 μA typical
N/A
SMBus Alert
Not present on LM75
N/A
VDD = 3.3 V
VDD = 5 V
Typical = 3 μA
Typical = 5.5 μA
Present on ADT75; 1 current
consumption @ 3.3 V
Setting Bit D7 in the configuration register enables SMBus
alert function, if required
3 V to 5.5 V
−55°C to +125°C
4.5 V to 5.5 V, ±2°C
typical
8, 9, 10, 11, 12
60 ms
500 μA
525 μA
8 μA maximum
12 μA maximum
78.6 μW typical
1
1
Specially designed to reduce power consumption.
The temperature accuracy specifications of the ADT75B are far better than those of the LM75, as shown in Table 3.
Table 3. Comparison of Temperature Accuracy Specifications for the LM75 and the ADT75B
LM75
Temperature Range
TA = −25°C to +100°C
TA = −55°C to +120°C
ADT75B
Accuracy
±2°C maximum
±3°C maximum
Temperature Range
TA = 0°C to 70°C
TA = −25°C to +100°C
TA = −55°C to +100°C
TA = 100°C to 125°C @ 3 V to 3.6 V VDD
Rev. 0 | Page 3 of 4
Accuracy
±1°C maximum
±2°C maximum
±3°C maximum
±3°C maximum
AN-876
ONE-SHOT REGISTER
One-shot mode is a feature of the ADT75. It is not available in
the LM75. LM75 software has no effect on this register and,
therefore, does not need to be modified.
This register is specifically designed to minimize power consumption. See the ADT75 data sheet for more information.
When one-shot mode is active, the following sequence of events
occurs:
1.
2.
3.
4.
The ADT75 is powered down.
0x04 is written to the address pointer register.
A conversion is performed
The part returns to power-down.
Table 4. ADT75 Registers
Pointer Address
0x00
0x01
0x02
0x03
0x04
Register Name
Temperature Value
Configuration
THYST
TOS Setpoint
One Shot
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
AN06439-0-11/06(0)
Rev. 0 | Page 4 of 4
Power-On Default
0x00
0x00
0x4B00 (75°C)
0x5000 (80°C)
0xXX
Similar pages