PDF Data Sheet Rev. PrG

SHARC+ Dual Core
DSP with ARM Cortex-A5
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
SYSTEM FEATURES
Dual enhanced SHARC+ high performance floating-point
cores
Up to 450 MHz per SHARC+ core
Up to 5 Mbits (640 kB) L1SRAM memory per core with
parity (optional ability to configure as cache)
32-bit, 40-bit, and 64-bit floating-point support
32-bit fixed point
Byte, short-word, word, long-word addressed
ARM Cortex-A5 core
450 MHz/720 DMIPS with Neon/VFPv4-D16/Jazelle
32 kB L1 instruction cache/32 kB L1 data cache
256 kB L2 cache with parity
Powerful DMA system
On-chip memory protection
Integrated safety features
19 mm × 19 mm 349/529 BGA (0.8 pitch), RoHS compliant
Low system power across automotive temperature range
MEMORY
Large on-chip L2 SRAM with ECC protection, up to 256 kB
On-chip L2 ROM (512 kB)
Two L3 interfaces optimized for low system power, providing
16-bit interface to DDR3, DDR2 or LPDDR1 SDRAM devices
ADDITIONAL FEATURES
Security and Protection
Crypto hardware accelerators
Fast secure boot with IP protection
Support for TrustZone®
Accelerators
High performance pipelined FFT/IFFT engine
FIR, IIR, HAE, SINC offload engines
PERIPHERALS
SYSTEM CONTROL
SRU
SECURITY AND PROTECTION
CORE 0
SYSTEM PROTECTION (SPU)
CORE 1
SYSTEM MEMORY
PROTECTION UNIT (SMPU)
CORE 2
S
FAULT MANAGEMENT
S
4× PRECISION CLOCK
GENERATORS
ASRC
8× PAIRS
2x DAI
FULL SPORT 2x PIN
0-7
BUFFER
2× S/PDIF Rx/Tx
ARM® TrustZone® SECURITY
2
DUAL CRC
WATCHDOGS
OTP MEMORY
THERMAL MONITOR UNIT (TMU)
L1 CACHE
32 kB L1 I-CACHE
32 kB L1 D-CACHE
L2 CACHE
256 kB (PARITY)
3× I C
L1 SRAM (PARITY)
L1 SRAM (PARITY)
5M BITS (640 kB)
SRAM/CACHE
5M BITS (640 kB)
SRAM/CACHE
2× LINK PORTS
2× SPI + 1× QUAD SPI
3× UARTs
1× EPPI
PROGRAM FLOW
3× ePWM
SYS EVENT CONTROLLER (SEC)
8× TIMERS + 1× COUNTER
TRIGGER ROUTING (TRU)
SYSTEM CROSSBAR AND DMA SUBSYSTEM
ADC CONTROL MODULE
(ACM)
CLOCK, RESET, AND POWER
G
P
I
O
ASYNC MEMORY (16-BIT)
CLOCK GENERATION (CGU)
2× CAN2.0
CLOCK DISTRIBUTION
UNIT (CDU)
REAL TIME CLOCK (RTC)
RESET CONTROL (RCU)
POWER MANAGEMENT (DPM)
L3 MEMORY
INTERFACES
DDR3
DDR2
LPDDR1
DDR3
DDR2
LPDDR1
16
16
DEBUG UNIT
ARM® CoreSightTM
WATCHPOINTS (SWU)
DATA
SYSTEM
L2 MEMORY
SYSTEM
ACCELERATION
2M BITS (256 kB)
L2 SRAM (ECC)
DSP FUNCTIONS
(FFT/iFFT, FIR, IIR, HAE/SINC)
4M BITS (512 kB)
2 × 2M BITS ROM
ENCRYPTION/DECRYPTION
SD/SDIO/eMMC
MLB 3-PIN
2× EMAC
SINC FILTER
8x SHARC FLAGS
2× USB 2.0 HS
MLB 6-PIN
DATA
PCIe2.0 (1 lane)
HADC (8 CHAN, 12-BIT)
Figure 1. Processor Block Diagram
SHARC and the SHARC logo are registered trademarks of Analog Devices, Inc.; SHARC+ is a trademark of Analog Devices, Inc.
Rev. PrG
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 U.S.A.
Tel: 781.329.4700
©2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
TABLE OF CONTENTS
General Description ................................................. 3
ADSP-SC58x/ADSP-2158x Designer Quick Reference .... 58
ARM Cortex-A5 Processor ...................................... 5
Specifications ........................................................ 80
SHARC Processor ................................................. 6
Operating Conditions ........................................... 80
SHARC+ Core Architecture .................................... 8
Electrical Characteristics ....................................... 83
System Infrastructure ........................................... 10
Absolute Maximum Ratings ................................... 87
System Memory Map ........................................... 11
ESD Sensitivity ................................................... 87
Security Features ................................................ 14
Package Information ............................................ 87
Safety Features ................................................... 14
Timing Specifications ........................................... 88
Processor Peripherals ........................................... 15
Environmental Conditions .................................. 152
System Acceleration ............................................ 20
System Design .................................................... 20
ADSP-SC58x/ADSP-2158x 349-Ball BGA Ball
Assignments .................................................... 153
System Debug .................................................... 23
Numerical by Ball Number ................................... 153
Development Tools ............................................. 23
Alphabetical by Pin Name .................................... 155
Additional Information ........................................ 24
Configuration of the 349-Ball CSP_BGA ................. 157
Related Signal Chains .......................................... 24
ADSP-SC58x/ADSP-2158x 529-Ball BGA Ball
Assignments .................................................... 158
Security Features Disclaimer .................................. 24
Numerical by Ball Number ................................... 158
ADSP-SC58x/ADSP-2158x Detailed Signal
Descriptions ...................................................... 25
Alphabetical by Pin Name .................................... 161
349-Ball CSP_BGA Signal Descriptions ....................... 30
Configuration of the 529-Ball CSP_BGA ................. 164
GPIO Multiplexing for 349-Ball CSP_BGA .................. 39
Outline Dimensions .............................................. 165
529-Ball CSP_BGA Signal Descriptions ....................... 42
Surface-Mount Design ........................................ 166
GPIO Multiplexing for 529-Ball CSP_BGA .................. 54
Ordering Guide ................................................ 167
REVISION HISTORY
6/2016—Revision PrF to Revision PrG
Revised Processor Comparison ................................... 4
Revised Processor Comparison for Automotive ............... 4
Updated Operating Conditions ................................. 80
Updated Environmental Conditions .......................... 152
Rev. PrG |
Page 2 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
GENERAL DESCRIPTION
The ADSP-SC58x/ADSP-2158x processors are members of the
SHARC® family of products. The ADSP-SC58x processor is
based on the SHARC+ dual-core and the ARM Cortex-A5 core.
The ADSP-SC58x/ADSP-2158x SHARC processors are members of the SIMD SHARC family of DSPs that feature Analog
Devices Super Harvard Architecture. These 32-bit/40-bit/64-bit
floating-point processors are optimized for high performance
audio/floating-point applications with their large on-chip
SRAM, multiple internal buses to eliminate I/O bottlenecks, and
innovative digital audio interfaces (DAI). New enhancements to
the SHARC+ core add cache enhancements, branch prediction,
and other instruction set improvements—all while maintaining
instruction set compatibility to previous SHARC products.
Table 1. Common Product Features
DAI (includes SRU)
Full SPORTs
S/PDIF Rx/Tx
ASRCs
Precision Clock Generators
I2C (TWI)
Quad Data Bit SPI
Dual Data Bit SPI
CAN2.0
UARTs
Link Ports
Enhanced PPI
GP Timer1
GP Counter
Enhanced PWMs2
Watchdog Timers
ADC Control Module
Static Memory Controller
Hardware Accelerators
High Performance FFT/IFFT
FIR/IIR
Harmonic Analysis Engine
SINC Filter
Security Crypto Engine
Multichannel 12-bit ADC
By integrating a rich set of industry-leading system peripherals
and memory (see Table 1, Table 2, and Table 3), the
ARM/SHARC processor is the platform of choice for next-generation applications that require RISC-like programmability,
multimedia support, and leading-edge signal processing in one
integrated package. These applications span a wide array of
markets, from automotive and pro-audio to industrial-based
applications that require high floating-point performance.
Table 2 provides feature comparison information for features
that vary across the standard processors.
Table 3 provides feature comparison information for features
that vary across the automotive processors.
1
2
Rev. PrG |
ADSP-SC58x / ADSP-2158x
2
2×4
2×1
2×4
2×2
3
1
2
2
3
2
1
8
1
3
2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
8-ch
Eight timers are available in the 529-BGA package only. The 349-BGA package
does not include Timer 6 and 7.
Three ePWMs are available in the 529-BGA package only. The 349-BGA package
does not include PWM 2.
Page 3 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 2. Processor Comparison
System
Memory
Processor Feature
ARM Cortex-A5 (MHz max)
ARM Core L1 Cache (I, D kB)
ARM Core L2 Cache (kB)
SHARC+ Core1 (MHz max)
SHARC+ Core2 (MHz max)
SHARC L1 SRAM/core (kB)
L2 SRAM (shared) (kB)
L2 ROM (shared) (kB)
DDR3/DDR2/LPDDR1
Controller (16-bit)
USB 2.0 HS + PHY (host/device/OTG)
USB 2.0 HS + PHY (host/device)
10/100 Std EMAC
10/100/1000 Std/AVB EMAC + Timer
IEEE-1588
SDIO/eMMC
PCIe 2.0 (1 Lane)
Real Time Clock (RTC)
GPIO Ports
GPIO + DAI Pins
Package Options: 19 mm × 19 mm
ADSPSC582
450
32, 32
256
450
–
640
256
512
ADSPSC583
450
32, 32
256
450
450
384
256
512
ADSPSC584
450
32, 32
256
450
450
640
256
512
ADSPSC587
450
32, 32
256
450
450
640
256
512
ADSPSC589
450
32, 32
256
450
450
640
256
512
ADSP21583
–
–
–
450
450
384
256
512
ADSP21584
–
–
–
450
450
640
256
512
ADSP21587
–
–
–
450
450
640
256
512
1
1
1
2
2
1
1
2
1
–
–
1
–
–
1
–
–
1
1
1
1
1
1
–
–
–
–
–
–
–
–
–
1
1
1
1
1
–
–
–
–
–
–
Port A–E
80 + 28
349-BGA
–
–
–
Port A–E
80 + 28
349-BGA
–
–
–
Port A–E
80 + 28
349-BGA
1
–
1
Port A–G
102 + 40
529-BGA
1
1
1
Port A–G
102 + 40
529-BGA
–
–
–
Port A–E
80 + 28
349-BGA
–
–
–
Port A–E
80 + 28
349-BGA
–
–
1
Port A–G
102 + 40
529-BGA
Table 3. Processor Comparison for Automotive
System
Memory
Processor Feature
ADSP-SC583W ADSP-SC584W ADSP-SC587W ADSP-SC589W ADSP-21583W ADSP-21584W
ARM Cortex-A5 (MHz max)
450
450
450
450
–
–
ARM Core L1 Cache (I, D kB)
32, 32
32, 32
32, 32
32, 32
–
–
ARM Core L2 Cache (kB)
256
256
256
256
–
–
SHARC+ Core1 (MHz max)
450
450
450
450
450
450
SHARC+ Core2 (MHz max)
450
450
450
450
450
450
SHARC L1 SRAM/core (kB)
384
640
640
640
384
640
L2 SRAM (shared) (kB)
256
256
256
256
256
256
L2 ROM (shared) (kB)
512
512
512
512
512
512
DDR3/DDR2/LPDDR1
1
1
2
2
1
1
Controller (16-bit)
USB 2.0 HS + PHY (host/device/OTG)
1
1
1
1
–
–
USB 2.0 HS + PHY (host/device)
–
–
1
1
–
–
10/100 Std EMAC
–
–
1
1
–
–
10/100/1000 Std/AVB EMAC + Timer
1
1
1
1
–
–
IEEE-1588
SDIO/eMMC
–
–
1
1
–
–
PCIe 2.0 (1 Lane)
–
–
–
1
–
–
MLB 3-pin/6-pin
1
1
1
1
1
1
Real Time Clock (RTC)
–
–
1
1
–
–
GPIO Ports
Port A–E
Port A–E
Port A–G
Port A–G
Port A–E
Port A–E
GPIO + DAI Pins
80 + 28
80 + 28
102 + 40
102 + 40
80 + 28
80 + 28
Package Options: 19 mm × 19 mm
349-BGA
349-BGA
529-BGA
529-BGA
349-BGA
349-BGA
Rev. PrG |
Page 4 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ARM CORTEX-A5 PROCESSOR
• ARM v7 debug architecture
The ARM Cortex-A5 processor (Figure 2) is a high performance
processor with the following features:
• Trace support through an embedded trace macrocell
(ETM) interface
• Extension: vector floating-point unit (IEEE754) with trapless execution
• Instruction and Data L1 cache units (32/32K bytes)
• In-order pipeline with dynamic branch prediction
• Extension: media processing engine (MPE) with NEON
technology
• ARM, Thumb, and ThumbEE instruction set support
• TrustZone security extensions
• Extension: Jazelle hardware acceleration
• Harvard level 1 memory system with a memory management unit (MMU)
EMBEDDED TRACE MACROCELL
(ETM) INTERFACE
CoreSight INTERFACE
CORTEX-A5
PROCESSOR
TM
DEBUG
DATA PROCESSING UNIT (DPU)
PREFETCH UNIT AND BRANCH PREDICTOR (PFU)
DATA MICRO-TLB
DATA STORE
BUFFER (STB)
DATA CACHE
UNIT (DCU)
NEON MEDIA
PROCESSING
ENGINE
CP15
INSTRUCTION MICRO-TLB
INSTRUCTION CACHE
UNIT (ICU)
MAIN TRANSMISSION
LOOKINSIDE BUFFER (TLB)
32 KB
32 KB
BUS INTERFACE UNIT (BIU)
A5 BUS MASTER PORT
GENERIC INTERRUPT
CONTROLLER
(PrimeCell® PL-390)
L2 CACHE
CONTROLLER
(CoreLinkTM PL-310)
DATA MASTER PORTS
SHARC PROCESSORS
256 KB
SYSTEM FABRIC
TO OTHER CORES
Figure 2. ARM Cortex A-5 Processor Block Diagram
Rev. PrG |
Page 5 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Generic Interrupt Controller, PL390 (ADSP-SC58x only)
L2 Cache Controller, PL310 (ADSP-SC58x only)
The generic interrupt controller (GIC) is a centralized resource
for supporting and managing interrupts. The ADSP-SC58x processor has a uniprocessor implementation of the GIC. The GIC
splits logically into GICPORT0 (distributor block) and
GICPORT1 (CPU interface block).
The L2 cache controller PL310 (Figure 2) works efficiently with
ARM processors that implement system fabric. The cache controller directly interfaces on the data and instruction interface.
The internal pipelining of the cache controller is optimized to
enable the processors to operate at the same clock frequency.
The cache controller supports:
Generic Interrupt Controller Port0 (GICPORT0)
• Two read/write 64-bit slave ports for interfacing with data
and instruction interfaces or for data between ARM and
SHARC cores
The GICPORT0 (distributor) performs interrupt prioritization
and distribution to the GICPORT1 (CPU interface) blocks that
connect to the processors in the system. It centralizes all interrupt sources, determines the priority of each interrupt, and
forwards the interrupt with the highest priority to the interface,
for priority masking and preemption handling.
• Two read/write 64-bit master ports for interfacing with the
system fabric
SHARC PROCESSOR
Generic Interrupt Controller Port1 (GICPORT1)
As shown in Figure 3, the SHARC processor integrates a
SHARC+ SIMD core, L1 memory crossbar, I/D cache controller, L1 memory blocks, and the master/slave ports. Figure 4
shows the SHARC+ SIMD core.
GICPORT1 (CPU interface) block performs priority masking
and preemption handling for a connected processor in the system. GICPORT1 supports 8 SGIs (software generated
interrupts) and 254 SPIs (shared peripheral interrupts).
B2
RAM
B2
B1
RAM
S
P-CACHE
B0
RAM
B2
RAM
SIMD Processor
CCLK DOMAIN
B0 (64)
B3
RAM
B1 (64)
D-CACHE
P-CACHE
B2 (64)
P-CACHE
D-CACHE
B3 (64)
I-CACHE
The SHARC processor supports a modified Harvard architecture in combination with a hierarchical memory structure.
Level 1 (L1) memories typically operate at the full processor
speed with little or no latency.
IO (32)
IO (32)
SLAVE
PORT 1
IO (32)
PM (64)
DM (64)
INTERNAL MEMORY INTERFACE (IMIF)
I/D CACHE CONTROL
SLAVE
PORT 2
IO (32)
SYSTEM FABRIC
SYSCLK
DOMAIN
CORE
MMR
(32)
DM (64)
CMD (64)
PM (64)
SHARC+
SIMD CORE
MASTER
PORT DATA
CMI (64)
PS (64/48)
MASTER
PORT INSTRUCTION
INTERRUPT
SEC
Figure 3. SHARC Processor Block Diagram
Rev. PrG |
Page 6 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
S+
DEBUG
TRACE
SIMD Core
BTB
BP
CEC
FLAGS
CONFLICT
CACHE
PM DATA 48
DMD/PMD 64
11-STAGE
PROGRAM SEQUENCER
PM ADDRESS 24
DAG1
16 × 32
DAG2
16 × 32
PM ADDRESS 32
SYSTEM
I/F
DM ADDRESS 32
PM DATA 64
TO
IMIF
USTAT
PX
DM DATA 64
MULTIPLIER
MRF
80-BIT
MRB
80-BIT
SHIFTER
ALU
DATA
SWAP
PEX
DATA
REGISTER
Rx
16 × 40-BIT
PEY
DATA
REGISTER
Sx
16 × 40-BIT
ASTATx
ASTATy
STYKx
STYKy
ALU
SHIFTER
MULTIPLIER
MSB
80-BIT
MSF
80-BIT
Figure 4. SHARC+ SIMD Core Block Diagram
L1 Memory
Figure 5 on Page 8 shows the ADSP-SC58x/ADSP-2158x memory structure. Each SHARC+ core has a tightly coupled Level 1
(L1) SRAM of up to 5 Mbits. Each SHARC+ core can access
code and data in a single cycle from this memory space. The
ARM Cortex-A5 core can also access these memory spaces with
multi-cycle accesses.
In the SHARC+ core private address space, both cores have
their own L1 memory.
SHARC+ core MMR address space is 0x 0000 0000-0x0003
FFFF in Normal Word (32-bit). Each block can be configured
for different combinations of code and data storage. Of the 5M
bits SRAM, up to 1024K bits can be configured for DM, PM,
and instruction cache. Each memory block supports single
cycle, independent accesses by the core processor and I/O processor. The memory architecture, in combination with its
separate on-chip buses, allows two data transfers from the core
and one from the I/O processor in a single cycle. The processor’s SRAM can be configured as a maximum of 160K words of
32-bit data, 320K words of 16-bit data, 106.7K words of 48-bit
Rev. PrG |
instructions (or 40-bit data), or combinations of different word
sizes up to 5 M bits. All of the memory can be accessed as 8-bit,
16-bit, 32-bit, 48-bit, or 64-bit words. A 16-bit floating-point
storage format is supported that effectively doubles the amount
of data that may be stored on chip.
Conversion between the 32-bit floating-point and 16-bit floating-point formats is performed in a single instruction. While
each memory block can store combinations of code and data,
accesses are most efficient when one block stores data using the
DM bus for transfers, and the other block stores instructions
and data using the PM bus for transfers.
Using the DM bus and PM buses, with one bus dedicated to a
memory block, assures single-cycle execution with two data
transfers. In this case, the instruction must be available in the
cache. The system configuration is flexible, but a configuration
is 512K bits DM, 128K bits PM, and 128K bits of cache, with the
remaining L1 memory configured as SRAM is typical. Each
addressable memory space outside the L1 memory can be
accessed either directly or via cache.
Page 7 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
The memory map in Table 4 on Page 11 gives the L1 memory
address space.
Preliminary Technical Data
0x FFFF FFFF
DMC1 (1GB)
0x C000 0000
In addition, there are multiple L1 memory blocks offering a
configurable mix of SRAM and cache.
DMC0 (1GB)
0x 8000 0000
SPI2 FLASH (512MB)
0x 6000 0000
L1 Master and Slave Ports
PCIe DATA (256MB)
0x 5000 0000
SMC BANK 3 (64MB)
Each SHARC+ core has two master and two slave ports to/from
the system fabric. One master port fetches instructions. The second master port drives data to the system world. Both slave
ports allow conflict-free core/DMA streams to the individual
memory blocks. For slave port addresses, refer to the L1 memory address map.
0x 4C00 0000
SMC BANK 2 (64MB)
0x 4800 0000
SMC BANK 1 (64MB)
0x 4400 0000
SMC BANK 0 (64MB)
0x 4000 0000
SYSTEM MMR SPACE
0x 3000 0000
RESERVED
L1 On-Chip Memory Bandwidth
0x 28FA 0000
The internal memory architecture allows programs to have four
accesses at the same time to any of the four blocks (assuming no
block conflicts). The total bandwidth is realized using the DMD
and PMD buses (2 × 64-bits, CCLK speed and 2 × 32-bit,
SYSCLK speed).
0x 28A4 0000
SHARC2 LI MEMORY IN
MULTIPROCESSOR SPACE
RESERVED
0x 287A 0000
0x 2824 0000
SHARC1 LI MEMORY IN
MULTIPROCESSOR SPACE
UNIFIED
ADDRESS
SPACE
RESERVED
0x 202B FFFF
L2 ROM 2 (2Mb)
0x 2028 0000
RESERVED
Instruction and Data Cache
0x 2020 7FFF
The ADSP-SC58x/ADSP-2158x processors also include a traditional instruction cache (I-cache) and two data caches. (PM/DM
caches). Together, these caches support one instruction access
and two data accesses, over the DM and PM buses, per cycle.
The cache controllers automatically manage the configured part
of the L1 memory. The system can configure part of the L1
memory for automatic management by the cache controllers.
The sizes of these caches are independently configurable from
zero to a maximum of 128 kB each. The memory not managed
by the cache controllers is directly addressable by the processors. The controllers ensure the data coherence between the two
data caches. The caches provide user-controllable features such
as locking (full as well as partial), range-bound invalidation, and
flushing.
0x 2020 0000
RESERVED
0x 201B FFFF
L2 ROM 1 (2Mb)
0x 2018 0000
RESERVED
0x 2010 7FFF
0x 2010 0000
RESERVED
L2 SRAM (2Mb)
0x 2008 0000
RESERVED
0x 2000 7FFF
0x 2000 0000
L2 BOOT ROM 0 (0.25Mb)
(ARM CORE 0)
0x 2000 0000
RESERVED
0x 0039 FFFF
L1 BLOCK 3 SRAM (1Mb)
0x 0038 0000
RESERVED
ARM
ADDRESS SPACE
RESERVED
0x 0031 FFFF
L1 BLOCK 2 SRAM (1Mb)
0x 0030 0000
RESERVED
0x 002E FFFF
L1 BLOCK 1 SRAM (1.5Mb)
SHARC PRIVATE
ADDRESS SPACE
The output of the SEC controller is forwarded to the core event
controller (CEC) to respond directly to all unmasked systembased interrupts. It also supports nesting including various SEC
interrupt channel arbitration options. For all SEC channels, the
processor automatically stacks the arithmetic status (ASTATx,
and STATy) registers and mode (MODE1) registers in parallel
with the interrupt servicing.
The core memory-mapped registers control L1 I/D cache, BTB,
L2 cache, parity error, system control, debug, and monitor
functions.
L2 BOOT ROM 1 (0.25Mb)
(SHARC Cores)
0x 200B FFFF
System Event Controller Input
Core Memory-Mapped Registers (CMMR)
L2 BOOT ROM 2 (0.25Mb)
(SHARC Cores)
0x 002C 0000
0x 1000 1000
ARM L2 CONFIG REGS (4KB)
RESERVED
0x 1000 0000
0x 0026 FFFF
RESERVED
L1 BLOCK 0 SRAM (1.5Mb)
0x 0000 7FFF
0x 0024 0000
ARM BOOT (32KB)
0x 0000 0000
RESERVED/CORE MMRs/
OTHER MEMORY ALIASES
0x 0000 0000
Figure 5. ADSP-SC58x/ADSP-2158x Memory Map
ADSP-2126x, ADSP-2136x, ADSP-2137x, ADSP-214xx, and
ADSP-2116x SIMD SHARC processors, as shown in Figure 4
and detailed in the following sections.
SIMD Computational Engine
SHARC+ CORE ARCHITECTURE
The ADSP-SC58x/ADSP-2158x processors are code compatible
at the assembly level with the ADSP-2148x, ADSP-2147x,
ADSP-2146x, ADSP-2137x, ADSP-2136x, ADSP-2126x,
ADSP-21160, and ADSP-21161, and with the first-generation
ADSP-2106x SHARC processors. The ADSP-SC58x/ADSP2158x processors share architectural features with the
Rev. PrG |
The SHARC+ core contains two computational processing elements that operate as a single-instruction, multiple-data
(SIMD) engine. The processing elements are referred to as PEx
and PEy and each contains an ALU, multiplier, shifter, and register file. PEx is always active, and PEy is enabled by setting the
PEYEN mode bit in the MODE1 register. SIMD mode allows
the processors to execute the same instruction in both
Page 8 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
processing elements, but each processing element operates on
different data. This architecture is efficient at executing mathintensive DSP algorithms. In addition to all the features of its
predecessors, the SHARC+ core also provides a new and simpler way to execute an instruction only on PEy.
Universal Registers
General-purpose tasks use these registers. The USTAT (4) registers allow easy bit manipulations (Set, Clear, Toggle, Test, XOR)
for all peripheral registers (control/status).
SIMD mode also affects the way data transfers between memory
and the processing elements because to sustain computational
operation in the processing elements requires twice the data
bandwidth. Therefore, entering SIMD mode also doubles the
bandwidth between memory and the processing elements.
When using the DAGs to transfer data in SIMD mode, two data
values transfer with each memory or register file access.
Independent, Parallel Computation Units
Within each processing element is a set of pipelined computational units. The computational units consist of an
arithmetic/logic unit (ALU), multiplier, and shifter. These units
are arranged in parallel, maximizing computational throughput.
These computational units support IEEE 32-bit single-precision
floating-point, 40-bit extended-precision floating-point, IEEE
64-bit double-precision floating-point, and 32-bit fixed-point
data formats.
Multifunction instruction set supports parallel execution of
ALU and multiplier operations. In SIMD mode, the parallel
ALU and multiplier operations occur in both processing elements per core.
Data Address Generators With Zero-Overhead Hardware
Circular Buffer Support
For indirect addressing and implementing circular data buffers
in hardware, the processor uses the two data address generators
(DAGs). Circular buffers allow efficient programming of delay
lines and other data structures required in digital signal processing, and are commonly used in digital filters and Fourier
transforms. The two DAGs of the processors contain sufficient
registers to allow the creation of up to 32 circular buffers (16
primary register sets, 16 secondary). The DAGs automatically
handle address pointer wraparound, reduce overhead, increase
performance, and simplify implementation. Circular buffers can
start and end at any memory location.
Flexible ISA Instruction Set
All processing operations take one cycle to complete. For all
floating-point operations, the processor takes two cycles to
complete in case of data dependency. Double-precision floating-point data take two to six cycles to complete. The processor
stalls for the appropriate number of cycles (interlocked pipeline
plus data dependency check).
Core Timer
Each SHARC+ processor core also has its own dedicated timer.
This extra timer is clocked by the internal processor clock and is
typically used as a system tick clock for generating periodic
operating system interrupts.
Data Register File
Each processing element contains a general-purpose data register file. The register files transfer data between the computation
units and the data buses, and store intermediate results. These
10-port, 32-register (16 primary, 16 secondary) register files,
combined with the enhanced Harvard architecture of the processor, allow unconstrained data flow between computation
units and internal memory. The registers in PEx are referred to
as R0-R15 and in PEy as S0-S15.
Context Switch
Many of the registers of the processor have secondary registers
that can activate during interrupt servicing for a fast context
switch. The data registers in the register file, the DAG registers,
and the multiplier result registers all have secondary registers.
The primary registers are active at reset, while control bits in a
mode control register activate the secondary registers.
Rev. PrG |
The data bus exchange register (PX) permits data to pass
between the 64-bit PM data bus and the 64-bit DM data bus, or
between the 40-bit register file and the PM/DM data bus. These
registers contain hardware to handle the data width difference.
The 48-bit instruction word accommodates various parallel
operations for concise programming. For example, the
processors can conditionally execute a multiply, an add, and a
subtract in both processing elements while branching and fetching up to four 32-bit values from memory—all in a single
instruction. Additionally, the double-precision floating-point
instruction set is an addition to the SHARC+ core.
Variable Instruction Set Architecture (VISA)
In addition to supporting the standard 48-bit instructions (ISA)
from previous SHARC processors, the SHARC+ core processors
support new instructions of 16 and 32 bits for ADSP-214xx
products. This feature, called Variable Instruction Set Architecture (VISA), drops redundant/unused bits within the 48-bit
instruction to create more efficient and compact code. The program sequencer supports fetching these 16-bit and 32-bit
instructions from both internal and external memories. VISA is
not an operating mode, it is only address-dependent (refer to
memory map ISA/VISA address spaces). Furthermore, it allows
jumps between ISA and VISA instruction fetches.
Single-Cycle Fetch of Instructional Four Operands
The ADSP-SC58x/ADSP-2158x processors feature an enhanced
Harvard architecture in which the data memory (DM) bus
transfers data and the program memory (PM) bus transfers
both instructions and data.
With its separate program and data memory buses and on-chip
instruction conflict-cache, the processors can simultaneously
fetch four operands (two over each data bus) and one instruction (from the conflict-cache), all in a single cycle.
Page 9 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Core Event Controller (CEC)
The SHARC+ core IVT generates various core interrupts (arithmetic and circular buffer instruction flow exceptions) and SEC
events (debug/monitor, software). The core only responds to
unmasked interrupts (IMASK register).
Instruction Conflict-Cache
The processors include a 32-entry instruction cache that enables
three-bus operation for fetching an instruction and four data
values. The cache is selective—only the instructions whose
fetches conflict with PM bus data accesses cache. This cache
allows full speed execution of core, looped operations such as
digital filter multiply-accumulates, and FFT butterfly processing. The conflict cache serves for on-chip bus conflicts only.
Preliminary Technical Data
• Storage for additional data for either ARM or SHARC+
cores to avoid external memory latencies and reduce external memory bandwidth
• Storage for incoming Ethernet traffic to improve
performance
• Storage for data coefficient tables cached by the SHARC+
core
See System Memory Protection Unit (SMPU) for options in
limiting access by specific cores and DMA masters.
The ARM Cortex-A5 core has an L1 instruction and data cache,
each of which is 32 kB in size. An L2 cache controller of 256 kB
is also available. When enabling the caches, accesses to all other
memory spaces (internal and external) go through the cache.
Branch Target Buffer/Branch Predictor
SHARC+ Core L1 Memory in Multiprocessor Space
Implementation of a hardware-based branch predictor (BP) and
branch target buffer (BTB) reduce branch delay. The program
sequencer supports efficient branching using this branch target
buffer (BTB) for conditional and unconditional instructions.
The ARM Cortex-A5 core can access the L1 memory of the
SHARC+ core. See Table 6 for the L1 memory address in multiprocessor space. The SHARC+ core can access the L1 memory
of the other SHARC+ core in the multiprocessor space.
Addressing Spaces
One-Time-Programmable Memory (OTP)
In addition to traditionally supported long-word, normal word,
extended-precision word and short word addressing aliases, the
processors support byte addressing for the data and instruction
accesses. The enhanced ISA/VISA provides new instructions for
accessing all sizes of data from byte space as well as for converting word addresses to byte and byte to word addresses.
The processors feature 7K bits of one-time-programmable
(OTP) memory which is memory-map accessible. This memory
stores a unique chip identification and supports secure-boot
and secure operation.
Additional Features
The enhanced ISA/VISA of the ADSP-SC58x/ADSP-2158x processors also provides memory barrier instruction (sync) for data
synchronization, exclusive data accesses support for multi-core
data sharing, and exclusive data accesses to enable
multiprocessor programming. To enhance the reliability of
application, L1 data RAMs support parity error detection logic
for every byte. Additionally, the processors detect illegal
opcodes. Core interrupts flag both the errors. Master ports of
the core also detect for failed external accesses.
I/O Memory Space
The static memory controller (SMC) is programmed to control
up to two blocks of external memories or memory-mapped
devices, with flexible timing parameters. Each block occupies an
8K byte segment regardless of the size of the device used.
Mapped I/Os also include PCIe data and SPI2 memory address
space. See Table 7.
SYSTEM INFRASTRUCTURE
The following sections describe the system infrastructure of the
ADSP-SC58x/ADSP-2158x processors.
System L2 Memory
A system level L2 memory of 2 Mbits (256 kB) is also available
to both SHARC+ cores, the ARM Cortex-A5 core, and DMA
channels. (See Table 5.) Memory accesses to this memory space
are multi-cycle accesses by both the ARM and SHARC+ cores.
The memory space is used for various cases including:
• ARM-to-SHARC+ core data sharing and inter-core
communications
• Accelerator and peripheral source and destination memory
to avoid having to access data in external memory
• A location for DMA descriptors
Rev. PrG |
Page 10 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
SYSTEM MEMORY MAP
Table 4. L1 Block 0, 1, 2, and 3 SHARC Addressing Memory Map (Private Address Space)
Memory
L1 Block 0 SRAM
(1.5 Mb)
L1 Block 1 SRAM
(1.5 Mb)
L1 Block 2 SRAM
(1 Mb)
L1 Block 3 SRAM
(1 Mb)
Long Word (64 Bits)
0x00048000–
0x0004DFFF
0x00058000–
0x0005DFFF
0x00060000–
0x00063FFF
0x00070000–
0x00073FFF
Extended Precision/
ISA Code
(48 Bits)
0x00090000–
0x00097FFF
0x000B0000–
0x000B7FFF
0x000C0000–
0x000C5554
0x000E0000–
0x000E5554
Normal Word
(32 Bits)
0x00090000–
0x0009BFFF
0x000B0000–
0x000BBFFF
0x000C0000–
0x000C7FFF
0x000E0000–
0x000E7FFF
Short Word/
VISA Code (16 Bits)
0x00120000–
0x00137FFF
0x00160000–
0x00177FFF
0x00180000–
0x0018FFFF
0x001C0000–
0x001CFFFF
Byte Access (8 Bits)
0x00240000–
0x0026FFFF
0x002C0000–
0x002EFFFF
0x00300000–
0x0031FFFF
0x00380000–
0x0039FFFF
Table 5. L2 Memory Addressing Map
Memory
L2 Boot-ROM01
L2 RAM (2 Mb)
Boot ROM1
L2 ROM1
Boot ROM2
L2 ROM2
1
Byte Address Space
ARM – Data Access and
Instruction Fetch
SHARC – Data Access
ARM: 0x00000000–0x00007FFF
SHARC/DMA: 0x20000000–0x20007FFF
0x20080000–0x200BFFFF
0x20100000–0x20107FFF
0x20180000–0x201BFFFF
0x20200000–0x20207FFF
0x20280000–0x202BFFFF
Normal Word Address
Space for Data Access
SHARC
Instruction Fetch
VISA Address Space
SHARC
Instruction Fetch
ISA Address Space
SHARC
0x08000000–0x08001FFF
0x08020000–0x0802FFFF
0x08040000–0x08041FFF
0x08060000–0x0806FFFF
0x08080000–0x08081FFF
0x080A0000–0x080AFFFF
0x00B80000–0x00B83FFF
0x00BA0000–0x00BBFFFF
0x00B00000–0x00B03FFF
0x00B20000–0x00B3FFFF
0x00B40000–0x00B43FFF
0x00B60000–0x00B7FFFF
0x00580000–0x00581555
0x005A0000–0x005AAAAF
0x00500000–0x00501555
0x00520000–0x0052AAAF
0x00540000–0x00541555
0x00560000–0x0056AAAF
From the ARM point of view, L2 Boot-ROM0 byte address space is 0x 0000 0000–0x 0000 7FFF.
Table 6. SHARC L1 Memory in Multiprocessor Space
L1 Memory of SHARC1 in
Multiprocessor Space
Address via Slave1 Port
Address via Slave2 Port
L1 Memory of SHARC2 in
Multiprocessor Space
Address via Slave1 Port
Address via Slave2 Port
Memory
Block
Block0
Block1
Block2
Block3
Block0
Block1
Block2
Block3
Block0
Block1
Block2
Block3
Block0
Block1
Block2
Block3
Rev. PrG |
Byte Address Space
for ARM and SHARC
0x28240000–0x28270000
0x282C0000–0x282F0000
0x28300000–0x28320000
0x28380000–0x283A0000
0x28640000–0x28670000
0x286C0000–0x286F0000
0x28700000–0x28720000
0x28780000–0x287A0000
0x28A40000–0x28A70000
0x28AC0000–0x28AF0000
0x28B00000–0x28B20000
0x28B80000–0x28BA0000
0x28E40000–0x28E70000
0x28EC0000–0x28EF0000
0x28F00000–0x28F20000
0x28F80000–0x28FA0000
Page 11 of 168 |
June 2016
Normal Word Address Space
for SHARC
0x0A090000–0x0A09C000
0x0A0B0000–0x0A0BC000
0x0A0C0000–0x0A0C8000
0x0A0E0000–0x0A0E8000
0x0A190000–0x0A19C000
0x0A1B0000–0x0A1BC000
0x0A1C0000–0x0A1C8000
0x0A1E0000–0x0A1E8000
0x0A290000–0x0A29C000
0x0A2B0000–0x0A2BC000
0x0A2C0000–0x0A2C8000
0x0A2E0000–0x0A2E8000
0x0A390000–0x0A39C000
0x0A3B0000–0x0A3BC000
0x0A3C0000–0x0A3C8000
0x0A3E0000–0x0A3E8000
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 7. Memory Map of Mapped I/Os
SMC Bank 0 (64 MB)
SMC Bank 1 (64 MB)
SMC Bank 2 (64 MB)
SMC Bank 3 (64 MB)
PCIe Data (256 MB)
SPI2 Memory (512 MB)
Byte Address Space
ARM – Data Access and
Instruction Fetch
SHARC – Data Access
0x40000000–0x43FFFFFF
0x44000000–0x47FFFFFF
0x48000000–0x4BFFFFFF
0x4C000000–0x4FFFFFFF
0x50000000–0x5FFFFFFF
0x60000000–0x7FFFFFFF
SHARC Core Instruction Fetch
Normal Word Address
Space for Data Access
SHARC
0x01000000–0x01FFFFFF
Not Available
Not Available
Not Available
0x02000000–0x03FFFFFF
0x04000000–0x07FFFFFF
VISA Space
0x00F00000–0x00F3FFFF
Not Available
Not Available
Not Available
0x00F40000–0x00F7FFFF
0x00F80000–0x00FFFFFF
ISA Space
0x00700000–0x0073FFFF
Not Available
Not Available
Not Available
0x00740000–0x0077FFFF
0x00780000–0x007FFFFF
Table 8. DMC Memory Map
DMC0 – 1 GB
DMC1 – 1 GB
Byte Address Space
ARM – Data Access and
Instruction Fetch
SHARC – Data Access
0x80000000–0xBFFFFFFF
0xC0000000–0xFFFFFFFF
SHARC Core Instruction Fetch
Normal Word Address
Space for Data Access
SHARC
0x10000000–0x17FFFFFF
0x18000000–0x1FFFFFFF
System Crossbars (SCB)
The system crossbars (SCB) are the fundamental building
blocks of a switch-fabric style for (on-chip) system bus interconnection. The SCBs connect system bus masters to system
bus slaves, providing concurrent data transfer between multiple
bus masters and multiple bus slaves. A hierarchical model—
built from multiple SCBs—provides a power and area efficient
system interconnect, which satisfies the performance and flexibility requirements of a specific system.
The SCBs provide the following features:
• Highly efficient, pipelined bus transfer protocol for sustained throughput
ISA Space
0x00400000–0x004FFFFF
0x00600000–0x006FFFFF
All DMAs can transport data to and from all on-chip and offchip memories. Programs can use two types of DMA transfers,
descriptor-based or register-based. Register-based DMA allows
the processors to program DMA control registers directly to initiate a DMA transfer. On completion, the control registers
automatically update with their original setup values for continuous transfer. Descriptor-based DMA transfers require a set of
parameters stored within memory to initiate a DMA sequence.
Descriptor-based DMA transfers allow multiple DMA
sequences to be chained together. Program a DMA channel to
set up and start another DMA transfer automatically after the
current sequence completes.
The DMA engine supports the following DMA operations:
• Full-duplex bus operation for flexibility and reduced
latency
• A single linear buffer that stops on completion
• A linear buffer with negative, positive or zero stride length
• Concurrent bus transfer support to allow multiple bus
masters to access bus slaves simultaneously
• Protection model (privileged/secure) support for selective
bus interconnect protection
Direct Memory Access (DMA)
The processors use direct memory access (DMA) to transfer
data within memory spaces or between a memory space and a
peripheral. The processors can specify data transfer operations
and return to normal processing while the fully integrated DMA
controller carries out the data transfers independent of processor activity.
DMA transfers can occur between memory and a peripheral or
between one memory and another memory. Each memory-tomemory DMA stream uses two channels, where one channel is
the source channel, and the second is the destination channel.
Rev. PrG |
VISA Space
0x00800000–0x00AFFFFF
0x00C00000–0x00EFFFFF
• A circular, auto-refreshing buffer that interrupts when each
buffer becomes full
• A similar buffer that interrupts on fractional buffers (for
example, 1/2, 1/4)
• 1D DMA: Uses a set of identical ping-pong buffers defined
by a linked ring of two-word descriptor sets, each containing a link pointer and an address
• 1D DMA: Uses a linked list of four word descriptor sets
containing a link pointer, an address, a length, and a
configuration
• 2D DMA: Uses an array of one-word descriptor sets, specifying only the base DMA address
• 2D DMA: Uses a linked list of multiword descriptor sets,
specifying everything
Page 12 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
servicing of a higher-priority event takes precedence over servicing of a lower-priority event. The processors provide support
for five different types of events:
Memory DMA (MDMA)
The processor supports various memory-to-memory DMA
operations which include:
• Emulation: An emulation event causes the processors to
enter emulation mode, allowing command and control of
the processors through the JTAG interface.
• Standard bandwidth MDMA channels with CRC protection (32-bit bus width, run on SCLK0)
• Enhanced bandwidth MDMA channel (32-bit bus width,
runs on SYSCLK)
• Reset: This event resets the processors.
• Maximum bandwidth MDMA channels (64-bit bus width,
run on SYCLK, one channel may be assigned to the FFT
accelerator)
Extended Memory DMA
Extended memory DMA supports various operating modes
such as delay line (allows processor reads and writes to external
delay line buffers and hence to external memory) with limited
core interaction and scatter/gather DMA (writes to/from noncontiguous memory blocks).
CRC Protection
The CRC protection modules allow system software to calculate
the signature of code or data or both in memory, the content of
memory-mapped registers, or communication message objects
periodically. Dedicated hardware circuitry compares the signature with pre-calculated values and triggers appropriate fault
events.
For example, every 100 ms the system software initiates the signature calculation of the entire memory contents and compares
these contents with expected, pre-calculated values. If a mismatch occurs, a fault condition is generated (through the
processor core or the trigger routing unit).
The CRC is a hardware module based on a CRC32 engine that
computes the CRC value of the 32-bit data words presented to
it. The source channel of the memory-to-memory DMA (in
memory scan mode) provides data. The data forwards optionally to the destination channel (memory transfer mode). The
main features of the CRC peripheral are:
• Exceptions: Events that occur synchronously to program
flow (in other words, the exception is taken before the
instruction is allowed to complete). Conditions triggered
on the one side by the SHARC+ core, such as data alignment (SIMD/long word) or compute violations (fixed or
floating point), and illegal instructions cause core exceptions. Conditions triggered on the other side by the SEC,
such as ECC/parity/watchdog/system clock, cause system
exceptions.
• Interrupts: Events that occur asynchronously to program
flow. They are caused by input signals, timers, and other
peripherals, as well as by an explicit software instruction.
System Event Controller (SEC)
Both SHARC+ cores feature a system event controller. System
event controller features include the following:
• Comprehensive system event source management including interrupt enable, fault enable, priority, core mapping
and source grouping
• Distributed programming model where each system event
source control and all status fields are independent of all
others
• Determinism where all system events have the same propagation delay and provide unique identification of a specific
system event source
• Slave Control Port which provides access to all SEC registers for configuration, status, and interrupt/fault service
model
• Global locking supports a register level protection model to
prevent writes to “locked” registers
• Memory scan mode
• Memory transfer mode
• Fault management including fault action configuration,
time out, external indication, and system reset
• Data verify mode
• Data fill mode
Trigger Routing Unit (TRU)
• User-programmable CRC32 polynomial
The TRU provides system-level sequence control without core
intervention. The TRU maps trigger masters (generators of triggers) to trigger slaves (receivers of triggers). Slave endpoints can
be configured to respond to triggers in various ways. Common
applications enabled by the TRU include:
• Bit/byte mirroring option (endianness)
• Fault/error interrupt mechanisms
• 1D and 2D fill block to initialize array with constants
• 32-bit CRC signature of a block of a memory or MMR
block
• Automatically triggering the start of a DMA sequence after
a sequence from another DMA channel completes
Event Handling
• Software triggering
The processors provide event handling that supports both nesting and prioritization. Nesting allows multiple event service
routines to be active simultaneously. Prioritization ensures that
• Synchronization of concurrent activities
Rev. PrG |
Page 13 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
SECURITY FEATURES
System Protection Unit (SPU)
The following sections describe the security features of the
ADSP-SC58x/ADSP-2158x processors.
The system protection unit (SPU) guards against accidental or
unwanted access to an MMR space of the peripheral by providing a write-protection mechanism. The user can choose and
configure the protected peripherals as well as configure which
ones of the four system MMR masters (core, memory DMA,
and CoreSight debug) the peripherals are guarded against.
ARM TrustZone
The ADSP-SC58x processors provide TrustZone technology,
which is tightly integrated into the Cortex-A5 processors. This
technology enables a secure state which is also extended
throughout the system through the AMBA AXI buses and interconnect fabric.
Crypto Hardware Accelerators
The ADSP-SC58x/ADSP-2158x processors support standardsbased hardware-accelerated encryption, decryption, authentication, and true random number generation.
Support for the following hardware-accelerated cryptographic
ciphers includes:
• AES in ECB, CBC, ICM, and CTR modes with 128-bit,
192-bit, and 256-bit keys
• DES in ECB and CBC mode with 56-bit key
• 3DES in ECB and CBC mode with 3x 56-bit key
• ARC4 in stateful, stateless mode, up to 128-bit key
Support for the following hardware-accelerated hash functions
includes:
• SHA-1
The SPU is also part of the security infrastructure. Along with
providing write-protection functionality, the SPU is employed
to define which resources in the system are secure or non-secure
and to block access to secure resources from non-secure
masters.
System Memory Protection Unit (SMPU)
Synonymously, the system memory protection unit (SMPU)
provides memory protection against read and/or write transactions to defined regions of memory. There are SMPU units in
the ADSP-SC58x/ADSP-2158x processors for each memory
space, except for SHARC L1 and SPI direct memory slave.
The SMPU is also part of the security infrastructure. It allows
the user to not only protect against arbitrary read and/or write
transactions, but it also allows regions of memory to be defined
as secure and prevent non-secure masters from accessing those
memory regions.
SAFETY FEATURES
The ADSP-SC58x/ADSP-2158x processors have been designed
to support functional safety applications. While the level of
safety is mainly dominated by the system concept, the following
primitives are provided by the devices to build a robust safety
concept.
• SHA-2 with 224-bit and 256-bit digest
• HMAC transforms for SHA-1 and SHA-2
• MD5
Public Key Accelerator is available to offload computationintensive public key cryptography operations.
Multi-Parity-Bit-Protected SHARC+ Core L1 Memories
Both a hardware-based non-deterministic random number generator and pseudo-random number generator are available.
Secure boot is also available with 224-bit elliptic curve digital
signatures ensuring integrity and authenticity of the boot
stream. Optionally, ensuring confidentiality through AES-128
encryption is available.
Employ secure debug to allow only trusted users to access the
system with debug tools.
CAUTION
This product includes security features that can be
used to protect embedded nonvolatile memory
contents and prevent execution of unauthorized
code. When security is enabled on this device
(either by the ordering party or the subsequent
receiving parties), the ability of Analog Devices to
conduct failure analysis on returned devices is
limited. Contact Analog Devices for details on the
failure analysis limitations for this device.
Rev. PrG |
In the SHARC+ core L1 memory space, whether SRAM or
cache, multiple parity bits protect each word to detect the single
event upsets that occur in all RAMs. Parity does not protect the
cache tags.
ECC-Protected L2 Memories
Error correcting codes (ECC) are used to correct single event
upsets. A single error correct-double error detect (SEC-DED)
code protects the L2 memory. By default ECC is enabled, but it
can be disabled on a per-bank basis. Single-bit errors correct
transparently. If enabled, dual-bit errors can issue a system
event or fault. ECC protection is fully transparent to the user,
even if L2 memory is read or written by 8-bit or 16-bit entities.
CRC-Protected Memories
While parity bit and ECC protection mainly protect against random soft errors in L1 and L2 memory cells, the CRC engines can
be used to protect against systematic errors (pointer errors) and
static content (instruction code) of L1, L2, and even L3 memories (DDR2, LPDDR). The processors feature two CRC engines
which are embedded in the memory-to-memory DMA controllers. CRC checksums can be calculated or compared on the fly
during memory transfers, or one or multiple memory regions
Page 14 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
can be continuously scrubbed by a single DMA work unit as per
DMA descriptor chain instructions. The CRC engine also protects data loaded during the boot process.
Signal Watchdogs
The eight general-purpose timers feature modes to monitor offchip signals. The watchdog period mode monitors whether
external signals toggle with a period within an expected range.
The watchdog width mode monitors whether the pulse widths
of external signals are within an expected range. Both modes
help to detect undesired toggling (or lack thereof) of
system-level signals.
System Event Controller (SEC)
Besides system events the SEC further supports fault management including fault action configuration as timeout, internal
indication by system interrupt, or external indication through
SYS_FAULT pin, and system reset.
PROCESSOR PERIPHERALS
The following sections describe the peripherals of the ADSPSC58x/ADSP-2158x processors.
Dynamic Memory Controller (DMC)
Serial Ports (SPORT)
The processors feature eight synchronous full serial ports. These
ports provide an inexpensive interface to a wide variety of digital and mixed-signal peripheral devices. These devices include
Analog Devices AD19xx/ADAU19xx family of audio codecs,
ADCs, and DACs. Two data lines, a clock, and frame sync make
up the serial ports. The data lines can be programmed to either
transmit or receive and each data line has a dedicated DMA
channel.
An individual full SPORT module consists of two independently configurable SPORT halves with identical
functionality. Two bidirectional data lines—primary (0) and
secondary (1) per SPORT half, configurable as either transmitters or receivers. Therefore, each SPORT half can be configured
for two transmitter or two receiver channels, permitting two
unidirectional streams into or out of the same full SPORT. This
bidirectional functionality provides greater flexibility for serial
communications. For full-duplex configuration, one half
SPORT provides two transmit signals, while the other half
SPORT provides the two receive signals. The frame sync and
clock are shared. The maximum SCLK is 1024xFS (TX master,
RX slave) and 512xFS (TX slave, RX master).
Serial ports operate in six modes:
The 16-bit DMC interfaces to:
• Standard DSP serial mode
• LPDDR1 (JESD209A) max freq 200 MHz DDRCLK
(64M bit – 2G bit)
• Multichannel (TDM) mode
• DDR2 (JESD79-2E) max freq 400 MHz DDRCLK
(256M bit – 4Gbit)
• Packed I2S mode
• I2S mode
• Left-justified mode
• DDR3 (JESD79-3E) max freq 450 MHz DDRCLK
(512M bit – 8G bit)
• Right-justified mode
See Table 8 for DMC memory map.
Asynchronous Sample Rate Converter (ASRC)
Digital Audio Interface (DAI)
The asynchronous sample rate converter (ASRC) contains eight
ASRC blocks. It is the same core as used in the AD1896 192 kHz
stereo asynchronous sample rate converter. It provides up to
140 dB SNR. The ASRC block performs synchronous or asynchronous sample rate conversion across independent stereo
channels, without using internal processor resources. The SRC
blocks can also be configured to operate together to convert
multichannel audio data without phase mismatches. Finally, the
ASRC can be used to clean up audio data from jittery clock
sources such as the S/PDIF receiver.
The processor supports two DAI units which are mirrored. Each
DAI can connect various peripherals to any of the DAI pins
(DAI_PIN20–PIN01).
Programs make these connections using the signal routing unit
(SRU), shown in Figure 1 on Page 1.
The SRU is a matrix routing unit (or group of multiplexers) that
enables the peripherals provided by the DAI to interconnect
under software control. This functionality allows easy use of the
DAI associated peripherals for a much wider variety of applications by using a larger set of algorithms than is possible with
nonconfigurable signal paths.
The DAI includes the peripherals described in the following sections. DAI pin buffers 20–19 can be used to change the polarity
of the input signals. Signals of the peripherals belonging to different DAIs cannot be interconnected, with few exceptions.
The DAI pin buffers may also be used as GPIO pins. DAI input
signals allow the triggering of interrupts on the rising edge, the
falling edge, or both edges.
Rev. PrG |
S/PDIF-Compatible Digital Audio Receiver/Transmitter
The Sony/Philips Digital Interface (S/PDIF) is a standard audio
data transfer format that allows the transfer of digital audio signals from one device to another without having to convert them
to an analog signal. There are two S/PDIF Tx/Rx blocks on the
processor. The digital audio interface carries three types of
information: audio data, non-audio data (compressed data),
and timing information.
The S/PDIF interface supports one stereo channel or compressed audio streams. The S/PDIF transmitter and receiver are
AES3-compliant. The S/PDIF receiver supports professional jitter standard.
Page 15 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
The S/PDIF receiver/transmitter has no separate DMA channels. It receives audio data in serial format and converts it into a
biphase encoded signal. The serial data input to the
receiver/transmitter can be formatted as left-justified, I2S or
right-justified with word widths of 16, 18, 20, or 24 bits. The
serial data, clock, and frame sync inputs to the S/PDIF
receiver/transmitter are routed through the signal routing unit
(SRU). They can come from various sources, such as the
SPORTs, external pins, and the precision clock generators
(PCGs), and are controlled by the SRU control registers.
Precision Clock Generators (PCG)
The precision clock generators (PCG) consist of four units,
units A/B located in DAI0, and units C/D located into DAI1.
The PCG can generate a pair of signals (clock and frame sync)
derived from a clock input signal (CLKIN1-0, SCLK0, DAI pin
buffer). Each unit can also access the opposite DAI unit. All
units are identical in functionality and operate independently of
each other. The two signals generated by each unit are normally
used as a serial bit clock/frame sync pair.
Parallel Peripheral Interface (PPI)
The processors provide a parallel peripheral interface (PPI) that
supports data widths up to 24 bits. The PPI supports direct connection to TFT LCD panels, parallel analog-to-digital and
digital-to-analog converters, video encoders and decoders,
image sensor modules and other general-purpose peripherals.
The features supported in the PPI module include:
• Programmable data length: 8 bits, 10 bits, 12 bits, 14 bits,
16 bits, 18 bits and 24 bits per clock
• Various framed, non-framed, and general-purpose operating modes. Frame syncs can be generated internally or can
be supplied by an external device.
• ITU-656 status word error detection and correction for
ITU-656 receive modes and ITU-656 preamble and status
word decode
• Optional packing and unpacking of data to/from 32 bits
from/to 8 bits, 16 bits, and 24 bits. If packing/unpacking is
enabled, endianness can be configured to change the order
of packing/unpacking of bytes/words.
• RGB888 can be converted to RGB666 or RGB565 for transmit modes.
• Various de-interleaving/interleaving modes for receiving/transmitting 4:2:2 YCrCb data
• Configurable LCD data enable (DEN) output available on
Frame Sync 3
UART Ports
The processors provide three full-duplex universal asynchronous receiver/transmitter (UART) ports, which are fully
compatible with PC-standard UARTs. Each UART port provides a simplified UART interface to other peripherals or hosts,
supporting full-duplex, DMA-supported, asynchronous
transfers of serial data. A UART port includes support for five to
eight data bits, and none, even, or odd parity. Optionally, an
Rev. PrG |
Preliminary Technical Data
additional address bit can be transferred to interrupt only
addressed nodes in multi-drop bus (MDB) systems. A frame is
terminated by a configurable number of stop bits.
The UART ports support automatic hardware flow control
through the clear-to-send (CTS) input and request-to-send
(RTS) output with programmable assertion FIFO levels.
To help support the Local Interconnect Network (LIN) protocols, a special command causes the transmitter to queue a break
command of programmable bit length into the transmit buffer.
Similarly, the number of stop bits can be extended by a programmable inter-frame space.
Serial Peripheral Interface (SPI) Ports
The processors have three industry-standard SPI-compatible
ports that allow it to communicate with multiple SPI-compatible devices.
The baseline SPI peripheral is a synchronous, four-wire interface consisting of two data pins, one device select pin, and a
gated clock pin. The two data pins allow full-duplex operation
to other SPI-compatible devices. An extra two (optional) data
pins are provided to support quad SPI operation. Enhanced
modes of operation such as flow control, fast mode, and dualI/O mode (DIOM) are also supported. In addition, a direct
memory access (DMA) mode allows for transferring several
words with minimal CPU interaction.
With a range of configurable options, the SPI ports provide a
glueless hardware interface with other SPI-compatible devices
in master mode, slave mode, and multimaster environments.
The SPI peripheral includes programmable baud rates, clock
phase, and clock polarity. The peripheral can operate in a multimaster environment by interfacing with several other devices,
acting as either a master device or a slave device. In a multimaster environment, the SPI peripheral uses open-drain outputs to
avoid data bus contention. The flow control features enable slow
slave devices to interface with fast master devices by providing
an SPI Ready pin which flexibly controls the transfers.
The baud rate and clock phase/polarities of the SPI port are programmable,. The port has integrated DMA channels for both
transmit and receive data streams.
Link Ports (LP)
Two 8-bit wide link ports can connect to the link ports of other
DSPs or peripherals. Link ports are bidirectional ports having
eight data lines, an acknowledge line, and a clock line.
ADC Control Module (ACM) Interface
The ADC control module (ACM) provides an interface that
synchronizes the controls between the processors and an analog-to-digital converter (ADC). The analog-to-digital
conversions are initiated by the processors, based on external or
internal events.
The ACM allows for flexible scheduling of sampling instants
and provides precise sampling signals to the ADC.
Page 16 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
The ACM synchronizes the ADC conversion process, generating the ADC controls, the ADC conversion start signal, and
other signals. The actual data acquisition from the ADC is done
by an internal DAI routing of ACM with SPORT0.
The processors interface directly to many ADCs without any
glue logic required.
• Frame status delivery to memory through DMA, including
frame completion semaphores for efficient buffer queue
management in software
• TX DMA support for separate descriptors for MAC header
and payload to eliminate buffer copy operations
• Convenient frame alignment modes
3-Phase Pulse Width Modulator (PWM) Units
The pulse width modulator (PWM) module is a flexible and
programmable waveform generator. With minimal CPU intervention the PWM peripheral is capable of generating complex
waveforms for motor control, pulse coded modulation (PCM),
digital-to-analog Conversion (DAC), power switching and
power conversion. The PWM module has four PWM pairs
capable of 3-phase PWM generation for source inverters for AC
induction and DC brushless motors.
Each of the three 3-phase PWM generation units features:
• 16-bit center-based PWM generation unit
• 47 MAC management statistics counters with selectable
clear-on-read behavior and programmable interrupts on
half maximum value
• Advanced power management
• Magic packet detection and wakeup frame filtering
• Support for 802.3Q tagged VLAN frames
• Programmable MDC clock rate and preamble suppression
Audio Video Bridging (AVB) Support
(10/100/1000 EMAC Only)
The 10/100/1000 EMAC supports the following audio video
(AVB) features:
• Programmable PWM pulse width
• Single update mode with option for asymmetric duty
• Separate channels or queues for AV data transfer in
100 Mbps and 1000 Mbps modes
• Programmable dead time and switching frequency
• Programmable dead time per channel
• Twos-complement implementation which permits smooth
transition to full ON and full OFF states
• Dedicated asynchronous PWM shutdown signal
Ethernet MAC (EMAC)
• Configuring up to two additional channels (Channel 1 and
Channel 2) on the transmit and receive paths for AV traffic.
Channel 0 is available by default and carries the legacy besteffort Ethernet traffic on the transmit side.
• Separate DMA, Tx FIFO, and Rx FIFO for AVB latency
class
The processor features two EMACs: 10/100 Std Ethernet and
10/100/1000 Std/AVB Ethernet with precision time protocol
IEEE-1588.
The processors can directly connect to a network by way of an
embedded fast Ethernet media access controller (MAC) that
supports 10-BaseT (10M bits/sec), 100-BaseT (100M bits/sec)
and 1000-BaseT (1G bits/sec) operations. The 10/100 Ethernet
MAC peripheral on the processors is fully compliant to the
IEEE 802.3-2002 standard. The peripheral provides programmable features designed to minimize supervision, bus use, or
message processing by the rest of the processor system.
Some standard features are:
• Support and RMII/RGMII protocols for external PHYs
• Programmable control to route received VLAN tagged
non-AV packets to channels or queues
Precision Time Protocol IEEE 1588 Support
The IEEE 1588 standard is a precision clock synchronization
protocol for networked measurement and control systems. The
processors include hardware support for IEEE 1588 with an
integrated precision time protocol synchronization engine
(PTP_TSYNC). This engine provides hardware assisted time
stamping to improve the accuracy of clock synchronization
between PTP nodes. The main features of the engine are:
• Support for both IEEE 1588-2002 and IEEE 1588-2008 protocol standards
• Full duplex and half-duplex modes
• Hardware assisted time stamping capable of up to 12.5 ns
resolution
• Media access management (in half-duplex operation)
• Flow control
• Lock adjustment
• Station management: generation of MDC/MDIO frames
for read-write access to PHY registers
• Automatic detection of IPv4 and IPv6 packets, as well as
PTP messages
Some advanced features are:
• Multiple input clock sources (SCLK0, RGMII, RMII, RMII
clock, external clock)
• Automatic checksum computation of IP header and IP
payload fields of RX frames
• Independent 32-bit descriptor-driven receive and transmit
DMA channels
Rev. PrG |
• IEEE 802.1-Qav specified credit-based shaper (CBS) algorithm for the additional transmit channels
• Programmable pulse per second (PPS) output
• Auxiliary snapshot to time stamp external events
Page 17 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Controller Area Network (CAN)
There are two CAN modules. A CAN controller implements the
CAN 2.0B (active) protocol. This protocol is an asynchronous
communications protocol used in both industrial and automotive control systems. The CAN protocol is well suited for
control applications due to its capability to communicate
reliably over a network. This is because the protocol incorporates CRC checking, message error tracking, and fault node
confinement.
The CAN controller offers the following features:
• 32 mailboxes (8 receive only, 8 transmit only, 16 configurable for receive or transmit)
• Dedicated acceptance masks for each mailbox
Preliminary Technical Data
value of the timer, enables the appropriate interrupt, then
enables the timer. Thereafter, the software must reload the
counter before it counts down to zero from the programmed
value. This protects the system from remaining in an unknown
state where software that would normally reset the timer has
stopped running due to an external noise condition or software
error.
General-Purpose Counters (CNT)
A 32-bit counter is provided that can operate in general-purpose up/down count modes and can sense 2-bit quadrature or
binary codes as typically emitted by industrial drives or manual
thumbwheels. Count direction is either controlled by a levelsensitive input pin or by two edge detectors.
A third counter input can provide flexible zero marker support
and can alternatively be used to input the push-button signal of
thumbwheel devices. All three pins have a programmable
debouncing circuit.
• Additional data filtering on first two bytes
• Support for both the standard (11-bit) and extended (29bit) identifier (ID) message formats
• Support for remote frames
Internal signals forwarded to a GP timer enable this timer to
measure the intervals between count events. Boundary registers
enable auto-zero operation or simple system warning by interrupts when programmed count values are exceeded.
• Active or passive network support
• Interrupts, including: TX complete, RX complete, error
and global
An additional crystal is not required to supply the CAN clock, as
the CAN clock is derived from a system clock through a programmable divider.
Timers
The processors include several timers which are described in the
following sections.
General-Purpose Timers (TIMER)
There is one GP timer unit, and it provides eight general-purpose programmable timers. Each timer has an external pin that
can be configured either as a pulse width modulator (PWM) or
timer output, as an input to clock the timer, or as a mechanism
for measuring pulse widths and periods of external events.
These timers can be synchronized to an external clock input on
the TIMER_TMRx pins, an external TIMER_CLK input pin, or
to the internal SCLK0.
These timer units can be used in conjunction with the UARTs
and the CAN controller to measure the width of the pulses in
the data stream to provide a software auto-baud detect function
for the respective serial channels.
The GP timers can generate interrupts to the processor core,
providing periodic events for synchronization to either the system clock or to external signals. Timer events can also trigger
other peripherals via the TRU (for instance, to signal a fault).
Each timer may also be started and/or stopped by any TRU
master without core intervention.
PCI Express (PCIe)
A PCI express interface is available on some product variants.
This single, bidirectional lane can be configured to be either a
root complex (RC) or end point (EP) system. The interface has
the following features:
• Compliance with the PCI Express Base Specification 3.0
• Support for transfers at either 2.5 Gbps (Gen 1.1) or
5.0 Gbps (Gen 2) in each direction
• Support for 8b/10b encode and decode
• Lane reversal and lane polarity inversion
• Flow control of data in both the transmit and receive
directions
• Support for removal of corrupted packets for error detection and recovery
• Maximum transaction payload of 256 bytes
Housekeeping Analog-to-Digital Converter (HADC)
The HADC provides a general-purpose, multichannel successive approximation A-to-D converter. It supports the following
set of features:
• 12-bit ADC core (10-bit accuracy) with built in sample and
hold
• 8 single-ended input channels that can be extended to 15
channels by adding an external channel multiplexer
• Throughput rates up to 1 MSPS
Watchdog Timer (WDT)
Two on-chip software watchdog timers can be used by the ARM
and/or SHARC+ cores. A software watchdog can improve system availability by forcing the processors to a known state, via a
general-purpose interrupt, or a fault, if the timer expires before
being reset by software. The programmer initializes the count
Rev. PrG |
• Single external reference with analog inputs between 0 and
3.3 V
• Selectable ADC clock frequency including the ability to
program a pre-scaler
Page 18 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
• Adaptable conversion type: allows single or continuous
conversion with option of autoscan
General-Purpose I/O (GPIO)
• Auto sequencing capability with up to 15 autoconversions
in a single session. Each conversion can be programmed to
select any 1–15 input channels.
• 16 data registers (individually addressable) to store conversion values
USB 2.0 On-the-Go Dual-Role Device Controller
There are two USB modules + PHY. USB0 supports HS/FS/LS
USB2.0 OTG and USB1 supports HS/FS USB2.0 only and can be
programmed to be a host or device.
Each USB 2.0 OTG dual-role device controller provides a lowcost connectivity solution for the growing adoption of this bus
standard in industrial applications, as well as consumer mobile
devices such as cell phones, digital still cameras, and MP3
players. The USB 2.0 controller allows these devices to transfer
data using a point-to-point USB connection without the need
for a PC host. The module can operate in a traditional USB
peripheral-only mode as well as the host mode presented in the
on-the-go (OTG) supplement to the USB 2.0 specification.
The USB clock is provided through a dedicated external crystal
or crystal oscillator.
The USB on-the-go dual-role device controller includes a phase
locked loop with programmable multipliers to generate the necessary internal clocking frequency for USB.
Media Local Bus (MLB)
The automotive model has a MLB slave interface which allows
the processors to function as a media local bus device. It
includes support for both 3-pin and 6-pin media local bus protocols. MLB 3-pin supports speeds up to 1024 × FS and 6-pin up
to 4096 × FS (48 kHz). MLB also supports up to 63 logical channels, with up to 468 bytes of data per media local bus frame.
The MLB interface supports MOST25/50/150 data rates and
operates in slave mode only.
2-Wire Controller Interface (TWI)
The processors include three 2-wire interface (TWI) modules
for providing a simple exchange method of control data
between multiple devices. The TWI module is compatible with
the widely used I2C bus standard. The TWI module offers the
capabilities of simultaneous master and slave operation and
support for both 7-bit addressing and multimedia data arbitration. The TWI interface utilizes two pins for transferring clock
(TWI_SCL) and data (TWI_SDA) and supports the protocol at
speeds up to 400k bits/sec. The TWI interface pins are compatible with 5 V logic levels.
Additionally, the TWI module is fully compatible with serial
camera control bus (SCCB) functionality for easier control of
various CMOS camera sensor devices.
Each general-purpose port pin can be individually controlled by
manipulation of the port control, status, and interrupt registers:
• GPIO direction control register: Specifies the direction of
each individual GPIO pin as input or output.
• GPIO control and status registers: A “write one to modify”
mechanism allows any combination of individual GPIO
pins to be modified in a single instruction, without affecting the level of any other GPIO pins.
• GPIO interrupt mask registers: Allow each individual
GPIO pin to function as an interrupt to the processors.
GPIO pins defined as inputs can be configured to generate
hardware interrupts, while output pins can be triggered by
software interrupts.
• GPIO interrupt sensitivity registers: Specify whether individual pins are level- or edge-sensitive and specify—if
edge-sensitive—whether just the rising edge or both the rising and falling edges of the signal are significant.
Pin Interrupts
Every port pin on the processors can request interrupts in either
an edge-sensitive or a level-sensitive manner with programmable polarity. Interrupt functionality is decoupled from GPIO
operation. Six system-level interrupt channels (PINT0–5) are
reserved for this purpose. Each of these interrupt channels can
manage up to 32 interrupt pins. The assignment from pin to
interrupt is not performed on a pin-by-pin basis. Rather, groups
of eight pins (half ports) can be flexibly assigned to interrupt
channels.
Every pin interrupt channel features a special set of 32-bit memory-mapped registers that enable half-port assignment and
interrupt management. This includes masking, identification,
and clearing of requests. These registers also enable access to the
respective pin states and use of the interrupt latches, regardless
of whether the interrupt is masked or not. Most control registers
feature multiple MMR address entries to write-one-to-set or
write-one-to-clear them individually.
Mobile Storage Interface (MSI)
The mobile storage interface (MSI) controller acts as the host
interface for multimedia cards (MMC), secure digital memory
cards (SD), and secure digital input/output cards (SDIO). The
MSI controller has the following features:
• Support for a single MMC, SD memory, SDIO card
• Support for 1-bit and 4-bit SD modes
• Support for 1-bit, 4-bit, and 8-bit MMC modes
• Support for eMMC 4.3 embedded NAND flash devices
• An 11-signal external interface with clock, command,
optional interrupt, and up to 8 data lines
• Integrated DMA controller
• Card interface clock generation from CLKO9 from CDU
• SDIO interrupt and read wait features
Rev. PrG |
Page 19 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
SYSTEM ACCELERATION
Sinus Cardinalis (SINC) Filter
The following sections describe the system acceleration blocks
of the ADSP-SC58x/ADSP-2158x processors.
The SINC module processes four bit streams using a pair of
configurable SINC filters for each bitstream. The purpose of the
primary SINC filter of each pair is to produce the filtered and
decimated output for the pair. The output may be decimated to
any integer rate between 8 and 256 times lower than the input
rate. Greater decimation allows greater removal of noise and
therefore greater ENOB.
FFT Accelerator
A high performance FFT/IFFT accelerator is available to greatly
improve the overall floating-point computation power of the
ADSP-SC58x/ADSP-2158x processors.
In addition, the following features are available to improve the
overall performance of the accelerator:
• Support for the IEEE-754/854 single-precision floatingpoint data format
• Automatic twiddle factor generation to reduce system
bandwidth
• Support for a vector complex multiply for windowing and
frequency domain filtering
• Ability to pipeline the data flow. This allows the accelerator
to bring in a new data set while the current set is being processed and the previous set is being sent out to memory.
This can provide a significant system-level performance
improvement.
• Ability to output the result as the magnitude squared of the
complex samples
• Dedicated, high-speed DMA controller with 64-bit buses
that can read and write data from any memory space
The FFT accelerator can be run concurrently with the other
accelerators on these processors.
Optional additional filtering outside the SINC module may be
used to further increase ENOB. The primary SINC filter output
is accessible through transfer to processor memory, or to
another peripheral, via DMA.
Each of the four channels is also provided with a low-latency
secondary filter with programmable positive and negative overrange detection comparators. These limit detection events can
be used to interrupt the core, generate a trigger, or signal a system fault.
Digital Transmission Content Protection (DTCP)
The ADSP-SC58x/ADSP-2158x processors support the AES128
data cipher engine.
The DTCP specification defines a cryptographic protocol for
protecting audio entertainment content from illegal copying,
intercepting, and tampering as it traverses high performance
digital buses, such as the IEEE 1394 standard. Only legitimate
entertainment content delivered to a source device via another
approved copy protection system (such as the DVD content
scrambling system) is protected by this copy protection system.
Contact Analog Devices for more information on DTCP.
FIR Accelerator
SYSTEM DESIGN
The FIR (finite impulse response) accelerator consists of a 1024
word coefficient memory, a 1024 word deep delay line for the
data, and four MAC units. A controller manages the accelerator.
The FIR accelerator runs at the peripheral clock frequency. It
can access all memory spaces and can run simultaneously with
other accelerators.
IIR Accelerator
The IIR (infinite impulse response) accelerator consists of a
1440 word coefficient memory for storage of biquad coefficients, a data memory for storing the intermediate data, and one
MAC unit. A controller manages the accelerator. The IIR accelerator runs at the peripheral clock frequency. It can access all
memory spaces and can run simultaneously with other
accelerators.
Harmonic Analysis Engine (HAE)
The harmonic analysis engine (HAE) block receives 8 kHz input
samples from two source signals whose frequencies are between
45 Hz and 65 Hz. The HAE will then process the input samples
and produce output results. The output results consist of power
quality measurements of the fundamental and up to
12 additional harmonics.
Rev. PrG |
The following sections provide an introduction to system design
options and power supply issues.
Clock Management
The processors provide three operating modes, each with a different performance/power profile. Control of clocking to each
of the processor peripherals also reduces power consumption.
The processors do not support any low power operation modes.
Control of clocking to each of the processor peripherals can
reduce the power consumption.
Reset Control Unit (RCU)
Reset is the initial state of the whole processor or the core and is
the result of a hardware- or software-triggered event. In this
state, all control registers are set to their default values and functional units are idle. Exiting a full system reset starts with the
core being ready to boot.
The reset control unit (RCU) controls how all the functional
units enter and exit reset. Differences in functional requirements and clocking constraints define how reset signals are
generated. Programs must guarantee that none of the reset
functions puts the system into an undefined state or causes
resources to stall. This is particularly important when the core is
reset (programs must ensure that there is no pending system
activity involving the core when it is being reset).
Page 20 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
From a system perspective reset is defined by both the reset target and the reset source as described below.
Target defined:
• System reset: All functional units except the RCU are set to
their default states.
• Hardware reset: All functional units are set to their default
states without exception. History is lost.
• Core-only reset: Affects the core only. The system software
should guarantee that the core, while in reset state, is not
accessed by any bus master.
Source defined:
• System reset: May be triggered by software (writing to the
RCU_CTL register) or by another functional unit such as
the dynamic power management (DPM) unit or any of the
system event controllers (SEC), trigger routing unit (TRU),
or emulator inputs.
• Hardware reset: The SYS_HWRST input signal is asserted
active (pulled down).
• Core-only reset: Triggered by software.
• Trigger request (peripheral).
Real-Time Clock (RTC)
The real-time clock (RTC) provides a robust set of digital watch
features, including current time, stopwatch, and alarm. The
RTC is clocked by a 32.768 kHz crystal external to the processor.
Connect RTC pins RTC0_CLKIN and RTC0_XTAL with external components as shown in Figure 6.
The RTC peripheral has dedicated power supply pins so that it
can remain powered up and clocked even when the rest of the
processor is in a low power state. The RTC provides several
programmable interrupt options, including interrupt per
second, minute, hour, or day clock ticks, interrupt on programmable stopwatch countdown, or interrupt at a programmed
alarm time.
RTC0_CLKIN
RTC0_XTAL
R1
X1
C1
the alarm control register. There are two alarms: The first alarm
is for a time of day. The second alarm is for a day and time of
that day.
The stopwatch function counts down from a programmed
value, with one-second resolution. When the stopwatch interrupt is enabled and the counter underflows, an interrupt is
generated.
Clock Generation Unit (CGU)
The ADSP-SC58x/ADSP-2158x processors support two independent PLLs. Each PLL is part of a clock generation unit
(CGU). (Refer to Figure 8 on Page 82.) Each CGU can either be
driven externally by the same clock source or each can be driven
by separate sources. This provides flexibility in determining the
internal clocking frequencies for each clock domain.
Frequencies generated by each CGU are derived from a common multiplier with different divider values available for each
output.
The clock generation unit (CGU) generates all on-chip clocks
and synchronization signals. Multiplication factors are programmed to define the PLLCLK frequency.
Programmable values divide the PLLCLK frequency to generate
the core clock (CCLK), the system clocks, the DDR1/2/3 clock
(DCLK), and the output clock (OCLK). For more information
on clocking, refer to the Clock Generation Unit (CGU) chapter
of the hardware reference manual.
Writing to the CGU control registers does not affect the behavior of the PLL immediately. Registers are first programmed with
a new value, and the PLL logic executes the changes so that it
transitions smoothly from the current conditions to the new
conditions.
System Crystal Oscillator and USB Crystal Oscillator
The processor can be clocked by an external crystal, (Figure 7) a
sine wave input, or a buffered, shaped clock derived from an
external clock oscillator. If an external clock is used, it should be
a TTL compatible signal and must not be halted, changed, or
operated below the specified frequency during normal operation. This signal is connected to the SYS_CLKIN pin of the
processor. When an external clock is used, the SYS_XTAL pin
must be left unconnected. Alternatively, because the processor
includes an on-chip oscillator circuit, an external crystal may be
used.
C2
For fundamental frequency operation, use the circuit shown in
Figure 7. A parallel-resonant, fundamental frequency, microprocessor grade crystal is connected across the SYS_CLKIN and
SYS_XTAL pins. The on-chip resistance between SYS_CLKIN
and the SYS_XTAL pin is in the 500 kΩ range. Further parallel
resistors are typically not recommended.
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
CONTACT CRYSTAL MANUFACTURER FOR DETAILS.
Figure 6. External Components for RTC
The 32.768 kHz input clock frequency is divided down to a 1 Hz
signal by a prescaler. The counter function of the timer consists
of four counters: a 60-second counter, a 60-minute counter, a
24-hour counter, and a 32,768-day counter. When the alarm
interrupt is enabled, the alarm function generates an interrupt
when the output of the timer matches the programmed value in
Rev. PrG |
The two capacitors and the series resistor shown in Figure 7
fine-tune phase and amplitude of the sine frequency. The capacitor and resistor values shown in Figure 7 are typical values
only. The capacitor values are dependent upon the load capacitance recommendations of the crystal manufacturer and the
PCB physical layout. The resistor value depends on the drive
Page 21 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Booting
SHARC PROCESSOR
The processors have several mechanisms for automatically loading internal and external memory after a reset. The boot mode is
defined by the SYS_BMODE input pins dedicated for this purpose. There are two categories of boot modes. In master boot
mode, the processor actively loads data from serial memories. In
slave boot modes, the processors receive data from external host
devices.
TO PLL
CIRCUITRY
ȍ
SYS_CLKIN
The boot modes are shown in Table 9. These modes are implemented by the SYS_BMODE bits of the reset configuration
register and are sampled during power-on resets and softwareinitiated resets.
SYS_XTAL
Nȍ *
FOR OVERTONE
OPERATION ONLY:
18 pF*
In the ADSP-SC58x processors, the ARM Cortex-A5 (core 0)
controls the boot process, including loading all internal and
external memory. Likewise, in the ADSP-2158x processors, the
SHARC+ (core 1) controls the boot function. The option for
secure boot is available on all products.
18 pF*
NOTE: VALUES MARKED WITH * MUST BE CUSTOMIZED, DEPENDING
ON THE CRYSTAL AND LAYOUT. ANALYZE CAREFULLY. FOR
FREQUENCIES ABOVE 33 MHz, THE SUGGESTED CAPACITOR VALUE
OF 18pF SHOULD BE TREATED AS A MAXIMUM.
Table 9. Boot Modes
Figure 7. External Crystal Connection
level specified by the crystal manufacturer. The user should verify the customized values based on careful investigations on
multiple devices over the required temperature range.
A third-overtone crystal can be used for frequencies above
25 MHz. The circuit is then modified to ensure crystal operation
only at the third overtone by adding a tuned inductor circuit as
shown in Figure 7. A design procedure for third-overtone operation is discussed in detail in application note “Using Third
Overtone Crystals with the ADSP-218x DSP” (EE-168). The
same recommendations may be used for the USB crystal
oscillator.
Clock Distribution Unit (CDU)
The two CGUs each provide outputs which feed a clock distribution unit (CDU). The clock outputs CLKO0-9 are connected
to various targets. For more information, refer to the Clock Distribution Unit (CDU) chapter of the hardware reference
manual.
SYS_BMODE Setting
000
001
010
011
100
101
110
111
Boot Mode
No boot
SPI2 Master
SPI2 Slave
Reserved
Reserved
Reserved
Link0 Slave
UART0 Slave
Thermal Monitoring Unit (TMU)
The thermal monitoring unit provides on-chip temp measurement which is important in applications that require substantial
power consumption. The TMU is integrated into the processor
die and digital infrastructure using an MMR-based system
access to measure the die temperature variations in real-time.
TMU features include:
Power-Up
• On-chip temperature sensing
XTAL oscillations (SYS_CLKIN) start when power is applied to
the VDD_EXT pins. The rising edge of SYS_HWRST starts onchip PLL locking (PLL lock counter). The deassertion should
apply only if all voltage supplies and SYS_CLKIN oscillations
are valid (refer to Power-Up Reset Timing on Page 88).
• Programmable over-temperature and under-temperature
limits
• Programmable conversion rate
Clock Out/External Clock
• Averaging feature available
The SYS_CLKOUT output pin has programmable options to
output divided-down versions of the on-chip clocks. By default,
the SYS_CLKOUT pin drives a buffered version of the
SYS_ CLKIN0 input. Refer to the Clock Distribution Unit
(CDU) chapter in the hardware reference manual to change the
default mapping of clocks.
• Programmable clock source selection to run the sensor off
an independent local clock
Power Supplies
The processors have separate power supply connections for:
• Internal (VDD_INT)
• External (VDD_EXT)
• USB (VDD_USB)
• HADC (VDD_HADC)
Rev. PrG |
Page 22 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
• RTC (VDD_RTC)
System Watchpoint Unit (SWU)
• DMC (VDD_DMC)
The system watchpoint unit (SWU) is a single module which
connects to a single system bus and provides for transaction
monitoring. One SWU is attached to the bus going to each
system slave. The SWU provides ports for all system bus address
channel signals. Each SWU contains four match groups of
registers with associated hardware. These four SWU match
groups operate independently, but share common event (interrupt, trigger and others) outputs.
• PCIe (VDD_PCIE, VDD_PCIE_TX and VDD_PCIE_RX)
All the power supplies should meet the specifications provided
in Operating Conditions on Page 80. All the external supply
pins must be connected to the same power supply.
Power Management
As shown in Table 10, the processor supports four different
power domains, which maximizes flexibility while maintaining
compliance with industry standards and conventions. There are
no sequencing requirements for the various power domains, but
all domains must be powered according to the appropriate
Specifications table for processor operating conditions; even if
the feature/peripheral is not used.
Table 10. Power Domains
Power Domain
All internal logic
DDR3/DDR2/LPDDR
USB
HADC
RTC
PCIe_TX
PCIe_RX
PCIe
All other I/O (includes SYS, JTAG, and
Ports pins)
Debug Access Port (DAP)
DAP (debug access port) provides IEEE-1149.1 JTAG interface
support through its JTAG debug. The DAP provides an optional
instrumentation trace for both the core and system. It provides
a trace stream that conforms to MIPI System Trace Protocol
version 2(STPv2).
DEVELOPMENT TOOLS
Analog Devices supports its processors with a complete line of
software and hardware development tools, including an integrated development environment (CrossCore® Embedded
Studio), evaluation products, emulators, and a wide variety of
software add-ins.
VDD Range
VDD_INT
VDD_DMC
VDD_USB
VDD_HADC
VDD_RTC
VDD_PCIE_TX
VDD_PCIE_RX
VDD_PCIE
VDD_EXT
Integrated Development Environments (IDEs)
For C/C++ software writing and editing, code generation, and
debug support, Analog Devices offers the CrossCore Embedded
Studio IDE.
The power dissipated by a processor is largely a function of its
clock frequency and the square of the operating voltage. For
example, reducing the clock frequency by 25% results in a 25%
reduction in dynamic power dissipation.
CrossCore Embedded Studio is based on the Eclipse framework.
Supporting most Analog Devices processor families, it is the
IDE of choice for processors, including multicore devices. CrossCore Embedded Studio seamlessly integrates available software
add-ins to support real time operating systems, file systems,
TCP/IP stacks, USB stacks, algorithmic software modules, and
evaluation hardware board support packages. For more information visit www.analog.com/cces.
Target Board JTAG Emulator Connector
EZ-KIT Lite Evaluation Board
Analog Devices DSP Tools product line of JTAG emulators uses
the IEEE 1149.1 JTAG test access port of the processor to monitor and control the target board processor during emulation.
Analog Devices DSP Tools product line of JTAG emulators
provides emulation at full processor speed, allowing inspection
and modification of memory, registers, and processor stacks.
The processor’s JTAG interface ensures that the emulator will
not affect target system loading or timing.
For processor evaluation, Analog Devices provides wide range
of EZ-KIT Lite® evaluation boards. Including the processor and
key peripherals, the evaluation board also supports on-chip
emulation capabilities and other evaluation and development
features. Also available are various EZ-Extenders®, which are
daughter cards delivering additional specialized functionality,
including audio and video processing. For more information
visit www.analog.com and search on “ezkit” or “ezextender”.
For complete information on Analog Devices’ SHARC DSP
Tools product line of JTAG emulator operation, see the appropriate Emulator Hardware User’s Guide.
EZ-KIT Lite Evaluation Kits
SYSTEM DEBUG
The processors include various features that allow for easy system debug. These are described in the following sections.
Rev. PrG |
For a cost-effective way to learn more about developing with
Analog Devices processors, Analog Devices offer a range of EZKIT Lite evaluation kits. Each evaluation kit includes an EZ-KIT
Lite evaluation board, directions for downloading an evaluation
version of the available IDE(s), a USB cable, and a power supply.
The USB controller on the EZ-KIT Lite board connects to the
USB port of the user’s PC, enabling the chosen IDE evaluation
suite to emulate the on-board processor in-circuit. This permits
the customer to download, execute, and debug programs for the
Page 23 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
EZ-KIT Lite system. It also supports in-circuit programming of
the on-board Flash device to store user-specific boot code,
enabling standalone operation. With the full version of
CrossCore Embedded Studio installed (sold separately), engineers can develop software for supported EZ-KITs or any
custom system utilizing supported Analog Devices processors.
Software Add-Ins for CrossCore Embedded Studio
Analog Devices offers software add-ins which seamlessly integrate with CrossCore Embedded Studio to extend its capabilities
and reduce development time. Add-ins include board support
packages for evaluation hardware, various middleware packages, and algorithmic modules. Documentation, help,
configuration dialogs, and coding examples present in these
add-ins are viewable through the CrossCore Embedded Studio
IDE once the add-in is installed.
Preliminary Technical Data
to run at full speed with no impact on system timing. The emulators require the target board to include a header that supports
connection of the DSP’s JTAG port to the emulator.
For details on target board design issues including mechanical
layout, single processor connections, signal buffering, signal termination, and emulator pod logic, see “Analog Devices JTAG
Emulation Technical Reference” (EE-68). This document is
updated regularly to keep pace with improvements to emulator
support.
ADDITIONAL INFORMATION
This data sheet provides a general overview of the ADSPSC58x/ADSP-2158x architecture and functionality. For detailed
information on the core architecture and instruction set, refer to
the programming reference manual.
RELATED SIGNAL CHAINS
Board Support Packages for Evaluation Hardware
Software support for the EZ-KIT Lite evaluation boards and EZExtender daughter cards is provided by software add-ins called
Board Support Packages (BSPs). The BSPs contain the required
drivers, pertinent release notes, and select example code for the
given evaluation hardware. A download link for a specific BSP is
located on the web page for the associated EZ-KIT or EZExtender product. The link is found in the Product Download
area of the product web page.
Middleware Packages
Analog Devices separately offers middleware add-ins such as
real time operating systems, file systems, USB stacks, and
TCP/IP stacks. For more information see the following web
pages:
A signal chain is a series of signal-conditioning electronic components that receive input (data acquired from sampling either
real-time phenomena or from stored data) in tandem, with the
output of one portion of the chain supplying input to the next.
Signal chains are often used in signal processing applications to
gather and process data or to apply system controls based on
analysis of real-time phenomena.
Analog Devices eases signal processing system development by
providing signal processing components that are designed to
work together well. A tool for viewing relationships between
specific applications and related components is available on the
www.analog.com website.
The application signal chains page in the Circuits from the Lab®
site (http:\\www.analog.com\circuits) provides:
• www.analog.com/ucos2
• Graphical circuit block diagram presentation of signal
chains for a variety of circuit types and applications
• www.analog.com/ucos3
• Drill down links for components in each chain to selection
guides and application information
• www.analog.com/ucfs
• www.analog.com/ucusbd
• Reference designs applying best practice design techniques
• www.analog.com/ucusbh
SECURITY FEATURES DISCLAIMER
• www.analog.com/lwip
Algorithmic Modules
To speed development, Analog Devices offers add-ins that perform popular audio and video processing algorithms. These are
available for use with CrossCore Embedded Studio. For more
information visit www.analog.com and search on “Blackfin software modules” or “SHARC software modules”.
Designing an Emulator-Compatible DSP Board (Target)
For embedded system test and debug, Analog Devices provides
a family of emulators. On each JTAG DSP, Analog Devices supplies an IEEE 1149.1 JTAG Test Access Port (TAP). In-circuit
emulation is facilitated by use of this JTAG interface. The
emulator accesses the processor’s internal features via the processor’s TAP, allowing the developer to load code, set
breakpoints, and view variables, memory, and registers. The
processor must be halted to send data and commands, but once
an operation is completed by the emulator, the DSP system is set
Rev. PrG |
To our knowledge, the Security Features, when used in accordance with the data sheet and hardware reference manual
specifications, provide a secure method of implementing code
and data safeguards. However, Analog Devices does not guarantee that this technology provides absolute security.
ACCORDINGLY, ANALOG DEVICES HEREBY DISCLAIMS
ANY AND ALL EXPRESS AND IMPLIED WARRANTIES
THAT THE SECURITY FEATURES CANNOT BE
BREACHED, COMPROMISED, OR OTHERWISE CIRCUMVENTED AND IN NO EVENT SHALL ANALOG DEVICES
BE LIABLE FOR ANY LOSS, DAMAGE, DESTRUCTION, OR
RELEASE OF DATA, INFORMATION, PHYSICAL PROPERTY, OR INTELLECTUAL PROPERTY.
Page 24 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ADSP-SC58x/ADSP-2158x DETAILED SIGNAL DESCRIPTIONS
Table 11 provides a detailed description of each pin.
Table 11. ADSP-SC58x/ADSP-2158x Detailed Signal Descriptions
Signal Name
ACM_A[n]
ACM_CLK
ACM_FS
ACM_T[n]
C1_FLG[n]
C2_FLG[n]
CAN_RX
CAN_TX
CNT_DG
Direction
Output
Output
Output
Input
InOut
InOut
Input
Output
Input
CNT_UD
Input
CNT_ZM
Input
DAI_PIN[nn]
InOut
DMC_A[nn]
DMC_BA[n]
Output
Output
DMC_CAS
Output
DMC_CK
DMC_CKE
DMC_CK
DMC_CS[n]
DMC_DQ[nn]
DMC_LDM
Output
Output
Output
Output
InOut
Output
DMC_LDQS
InOut
DMC_LDQS
DMC_ODT
InOut
Output
DMC_RAS
Output
DMC_RESET
DMC_RZQ
DMC_UDM
Output
InOut
Output
Description
ADC Control Signals. Function varies by mode
Clock. SCLK derived clock for connecting to an ADC.
Frame Sync. Typically used as an ADC chip select.
External Trigger n. Input for external trigger events
SHARC+ Core 1 Flag Pin.
SHARC+ Core 2 Flag Pin.
Receive. Typically an external CAN transceiver’s RX output.
Transmit. Typically an external CAN transceiver’s TX input.
Count Down and Gate. Depending on the mode of operation this input acts either as a count down
signal or a gate signal.
Count down: This input causes the GP counter to decrement.
Gate: Stops the GP counter from incrementing or decrementing.
Count Up and Direction. Depending on the mode of operation this input acts either as a count up
signal or a direction signal.
Count up: This input causes the GP counter to increment.
Direction: Selects whether the GP counter is incrementing or decrementing.
Count Zero Marker. Input that connects to the zero marker output of a rotary device or detects the
pressing of a pushbutton.
Pin n. The digital applications interfaces (DAI0 and DAI1) provide the ability to
connect various peripherals to any of the DAI pins (DAI0_PINxx and DAI1_PINxx). Programs make
these connections using the signal routing unit (SRU). Both DAI units are symmetric. The shared
DAIx__PIN03 and DAIx_PIN04 pins allow routing between both DAI units.
Address n. Address bus
Bank Address n. Defines which internal bank an ACTIVATE, READ, WRITE, or PRECHARGE command
is being applied to on the dynamic memory. Also defines which mode registers (MR, EMR, EMR2,
and/or EMR3) are loaded during the LOAD MODE REGISTER command.
Column Address Strobe. Defines the operation for external dynamic memory to perform in
conjunction with other DMC command signals. Connect to the CAS input of dynamic memory.
Clock. Outputs DCLK to external dynamic memory.
Clock enable. Active high clock enables. Connects to the dynamic memory's CKE input.
Clock (complement). Complement of DMC_CK.
Chip Select n. Commands are recognized by the memory only when this signal is asserted.
Data n. Bidirectional Data bus
Data Mask for Lower Byte. Mask for DMC_DQ07:DMC_DQ00 write data when driven high. Sampled
on both edges of the data strobe by the dynamic memory.
Data Strobe for Lower Byte. DMC_DQ07:DMC_DQ00 data strobe. Output with Write Data. Input with
Read Data. May be single-ended or differential depending on register settings.
Data Strobe for Lower Byte (complement). Complement of LDQS. Not used in single-ended mode.
On-die termination. Enables dynamic memory termination resistances when driven high (assuming
the memory is properly configured).
Row Address Strobe. Defines the operation for external dynamic memory to perform in conjunction
with other DMC command signals. Connect to the RAS input of dynamic memory.
Reset (DDR3 only).
External calibration resistor connection.
Data Mask for Upper Byte. Mask for DMC_DQ15:DMC_DQ08 write data when driven high. Sampled
on both edges of the data strobe by the dynamic memory.
Rev. PrG |
Page 25 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 11. ADSP-SC58x/ADSP-2158x Detailed Signal Descriptions (Continued)
Signal Name
DMC_UDQS
Direction
InOut
DMC_UDQS
DMC_VREF
DMC_WE
InOut
Input
Output
ETH_CRS
Input
ETH_MDC
ETH_MDIO
ETH_PTPAUXIN[n]
Output
InOut
Input
ETH_PTPCLKIN[n]
ETH_PTPPPS[n]
Input
Output
ETH_REFCLK
ETH_RXCLK_REFCLK
ETH_RXCTL_CRS
ETH_RXD[n]
ETH_TXCLK
ETH_TXCTL_TXEN
ETH_TXD[n]
ETH_TXEN
HADC_EOC_DOUT
Input
InOut
InOut
Input
Input
InOut
Output
InOut
Output
HADC_MUX[n]
Output
HADC_VIN[n]
HADC_VREFN
Input
Input
HADC_VREFP
Input
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
LP_ACK
Input
Input
Output
Input
Input
InOut
LP_CLK
InOut
LP_D[n]
MLB_CLKN
MLB_CLKP
MLB_DATN
InOut
Input
Input
InOut
Description
Data Strobe for Upper Byte. DMC_DQ15:DMC_DQ08 data strobe. Output with Write Data. Input with
Read Data. Not used in single-ended mode.
Data Strobe for Upper Byte (complement). Complement of UDQS. Not used in single-ended mode.
Voltage Reference. Externally driven to VDD_DMC/2.
Write Enable. Defines the operation for external dynamic memory to perform in conjunction with
other DMC command signals. Connect to the WEb input of dynamic memory.
Carrier Sense/RMII Receive Data Valid. Multiplexed on alternate clock cycles.
CRS: Asserted by the PHY when either the transmit or receive medium is not idle. Deasserted when
both are idle.
RXDV: Asserted by the PHY when the data on RXDn is valid.
Management Channel Clock. Clocks the MDC input of the PHY.
Management Channel Serial Data. Bidirectional data bus for PHY control.
PTP Auxiliary Trigger Input. Assert this signal to take an auxiliary snapshot of the time and store it
in the auxiliary time stamp FIFO.
PTP Clock Input. Optional external PTP clock input
PTP Pulse-Per-Second Output. When the Advanced Time Stamp feature is enable this signal is
asserted based on the PPS mode selected. Otherwise, PTPPPS is asserted every time the seconds
counter is incremented.
Reference Clock. Externally supplied Ethernet clock
RXCLK (GigE) or REFCLK (10/100).
RXCTL (GigE) or CRS (10/100).
Receive Data n. Receive data bus
Reference Clock. Externally supplied Ethernet clock
TXCTL (GigE) or TXEN (10/100).
Transmit Data n. Transmit data bus
Transmit Enable. When asserted indicates that the data on TXDn is valid.
End of Conversion / Serial Data Out. Transitions high for one cycle of the HADC internal clock at the
end of every conversion. Alternatively, HADC serial data out can be seen by setting the appropriate
bit in HADC_CTL.
Controls to external multiplexer. Allows additional input channels when connected to an external
multiplexer.
Analog Input at channel n. Analog voltage inputs for digital conversion.
Ground Reference for ADC. Connect to an external voltage reference that meets data sheet
specifications.
External Reference for ADC. Connect to an external voltage reference that meets data sheet
specifications.
JTAG Clock. JTAG test access port clock.
JTAG Serial Data In. JTAG test access port data input.
JTAG Serial Data Out. JTAG test access port data output.
JTAG Mode Select. JTAG test access port mode select.
JTAG Reset. JTAG test access port reset.
Acknowledge. Provides handshaking. When the link port is configured as a receiver, ACK is an output.
When the link port is configured as a transmitter, ACK is an input.
Clock. When the link port is configured as a receiver, CLK is an input. When the link port is configured
as a transmitter, CLK is an output.
Data n. Data bus. Input when receiving, output when transmitting.
Differential Clock (–)
Differential Clock (+)
Differential Data (–)
Rev. PrG |
Page 26 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 11. ADSP-SC58x/ADSP-2158x Detailed Signal Descriptions (Continued)
Signal Name
MLB_DATP
MLB_SIGN
MLB_SIGP
MLB_CLK
MLB_DAT
MLB_SIG
MLB_CLKOUT
MSI_CD
MSI_CLK
MSI_CMD
MSI_D[n]
MSI_INT
Direction
InOut
InOut
InOut
Input
InOut
InOut
Output
Input
Output
InOut
InOut
Input
PCIE_CLKM
PCIE_CLKP
PCIE_REF
PCIE_RXM
PCIE_RXP
PCIE_TXM
PCIE_TXP
PPI_CLK
PPI_D[nn]
PPI_FS1
PPI_FS2
PPI_FS3
PWM_AH
PWM_AL
PWM_BH
PWM_BL
PWM_CH
PWM_CL
PWM_DH
PWM_DL
PWM_SYNC
InOut
InOut
InOut
InOut
InOut
InOut
InOut
InOut
InOut
InOut
InOut
InOut
Output
Output
Output
Output
Output
Output
Output
Output
Input
PWM_TRIP[n]
P_[nn]
Input
InOut
RTC_CLKIN
RTC_XTAL
Input
Output
SINC_CLK0
SINC_CLK1
SINC_D0
SINC_D1
SINC_D2
SINC_D3
InOut
InOut
InOut
InOut
InOut
InOut
Description
Differential Data (+)
Differential Signal (–)
Differential Signal (+)
Single-Ended Clock
Single-Ended Data
Single-Ended Signal
Single-Ended Clock Out
Card Detect. Connects to a pull-up resistor and to the card detect output of an SD socket.
Clock. The clock signal applied to the connected device from the MSI.
Command. Used to send commands to and receive responses from the connected device.
Data n. Bidirectional data bus.
eSDIO Interrupt Input. Used only for eSDIO. Connects to an eSDIO card's interrupt output. An
interrupt may be sampled even when the MSI clock to the card is switched off.
CLK –
CLK +
Reference Resistor. Attach a 200- Ω 1% 100-ppm/C precision resistor-to-ground on the board.
RX –
RX +
TX –
TX +
Clock. Input in external clock mode, output in internal clock mode.
Data n. Bidirectional data bus.
Frame Sync 1 (HSYNC). Behavior depends on EPPI mode. See the EPPI HRM chapter for more details.
Frame Sync 2 (VSYNC). Behavior depends on EPPI mode. See the EPPI HRM chapter for more details.
Frame Sync 3 (FIELD). Behavior depends on EPPI mode. See the EPPI HRM chapter for more details.
Channel A High Side. High side drive signal
Channel A Low Side. Low side drive signal
Channel B High Side. High side drive signal
Channel B Low Side. Low side drive signal
Channel C High Side. High side drive signal
Channel C Low Side. Low side drive signal
Channel D High Side. High side drive signal
Channel D Low Side. Low side drive signal
PWMTMR Grouped. This input is for an externally generated sync signal. If the sync signal is internally
generated no connection is necessary.
Shutdown Input n. When asserted the selected PWM channel outputs are shut down immediately.
Position n. General purpose input/output. See the GP Ports chapter of the HRM for programming
information.
Crystal input / external oscillator connection. Connect to an external clock source or crystal.
Crystal output. Drives an external crystal. Must be left unconnected if an external clock is driving
RTC_CLKIN.
Clock 0
Clock 1
Data 0
Data 1
Data 2
Data 3
Rev. PrG |
Page 27 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 11. ADSP-SC58x/ADSP-2158x Detailed Signal Descriptions (Continued)
Signal Name
SMC_ABE[n]
Direction
Output
SMC_AMS[n]
SMC_AOE
SMC_ARDY
Output
Output
Input
SMC_ARE
SMC_AWE
SMC_A[nn]
SMC_D[nn]
SPI_CLK
SPI_D2
SPI_D3
SPI_MISO
Output
Output
Output
InOut
InOut
InOut
InOut
InOut
SPI_MOSI
InOut
SPI_RDY
SPI_SEL[n]
SPI_SS
InOut
Output
Input
SPT_ACLK
InOut
SPT_AD0
InOut
SPT_AD1
InOut
SPT_AFS
InOut
SPT_ATDV
Output
SPT_BCLK
InOut
SPT_BD0
InOut
SPT_BD1
InOut
SPT_BFS
InOut
SPT_BTDV
Output
SYS_BMODE[n]
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
Input
Input
Input
Output
Description
Byte Enable n. Indicate whether the lower or upper byte of a memory is being accessed. When an
asynchronous write is made to the upper byte of a 16-bit memory, SMC_ABE1b = 0 and
SMC_ABE0b = 1. When an asynchronous write is made to the lower byte of a 16-bit memory,
SMC_ABE1b = 1 and SMC_ABE0b = 0.
Memory Select n. Typically connects to the chip select of a memory device.
Output Enable Asserts at the beginning of the setup period of a read access.
Asynchronous Ready. Flow control signal used by memory devices to indicate to the SMC when
further transactions may proceed.
Read Enable. Asserts at the beginning of a read access.
Write Enable. Asserts for the duration of a write access period.
Address n. Address bus
Data n. Bidirectional data bus
Clock. Input in slave mode, output in master mode.
Data 2. Used to transfer serial data in Quad mode. Open-drain when ODM mode is enabled.
Data 3. Used to transfer serial data in Quad mode. Open-drain when ODM mode is enabled.
Master In, Slave Out. Used to transfer serial data. Operates in the same direction as SPI_MOSI in Dual
and Quad modes. Open-drain when ODM mode is enabled.
Master Out, Slave In. Used to transfer serial data. Operates in the same direction as SPI_MISO in Dual
and Quad modes. Open-drain when ODM mode is enabled.
Ready. Optional flow signal. Output in slave mode, input in master mode.
Slave Select Output n. Used in Master mode to enable the desired slave.
Slave Select Input. Slave mode: Acts as the slave select input.
Master mode: Optionally serves as an error detection input for the SPI when there are multiple masters.
Channel A Clock. Data and Frame Sync are driven/sampled with respect to this clock. This signal can
be either internally or externally generated.
Channel A Data 0. Primary bidirectional data I/O. This signal can be configured as an output to
transmit serial data, or as an input to receive serial data.
Channel A Data 1. Secondary bidirectional data I/O. This signal can be configured as an output to
transmit serial data, or as an input to receive serial data.
Channel A Frame Sync. The frame sync pulse initiates shifting of serial data. This signal is either
generated internally or externally.
Channel A Transmit Data Valid. This signal is optional and only active when SPORT is configured in
multichannel transmit mode. It is asserted during enabled slots.
Channel B Clock. Data and Frame Sync are driven/sampled with respect to this clock. This signal can
be either internally or externally generated.
Channel B Data 0. Primary bidirectional data I/O. This signal can be configured as an output to
transmit serial data, or as an input to receive serial data.
Channel B Data 1. Secondary bidirectional data I/O. This signal can be configured as an output to
transmit serial data, or as an input to receive serial data.
Channel B Frame Sync. The frame sync pulse initiates shifting of serial data. This signal is either
generated internally or externally.
Channel B Transmit Data Valid. This signal is optional and only active when SPORT is configured in
multichannel transmit mode. It is asserted during enabled slots.
Boot Mode Control n. Selects the boot mode of the processor.
Clock/Crystal Input
Clock/Crystal Input
Processor Clock Output. Outputs internal clocks. Clocks may be divided down. See the CGU chapter
of the HRM for more details.
Rev. PrG |
Page 28 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 11. ADSP-SC58x/ADSP-2158x Detailed Signal Descriptions (Continued)
Signal Name
SYS_FAULT
Direction
InOut
SYS_FAULT
InOut
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
TM_ACI[n]
TM_ACLK[n]
TM_CLK
TM_TMR[n]
TRACE_CLK
TRACE_D[nn]
TWI_SCL
TWI_SDA
UART_CTS
UART_RTS
UART_RX
Input
Output
Output
Output
Input
Input
Input
InOut
Output
Output
InOut
InOut
Input
Output
Input
UART_TX
Output
USB_CLKIN
Input
USB_DM
USB_DP
USB_ID
InOut
InOut
Input
USB_VBC
Output
USB_VBUS
USB_XTAL
InOut
Output
Description
Active-High Fault Output. Indicates indicates internal faults or senses external faults depending on
the operating mode.
Active-Low Fault Output. Indicates indicates internal faults or senses external faults depending on
the operating mode.
Processor Hardware Reset Control. Resets the device when asserted.
Reset Output. Indicates that the device is in the reset state.
Crystal Output
Crystal Output
Alternate Capture Input n. Provides an additional input for WIDCAP, WATCHDOG, and PININT modes.
Alternate Clock n. Provides an additional time base for use by an individual timer.
Clock. Provides an additional global time base for use by all the GP timers.
Timer n. The main input/output signal for each timer.
Trace Clock. Clock output/
Trace Data n. Unidirectional data bus.
Serial Clock. Clock output when master, clock input when slave
Serial Data. Receives or transmits data
Clear to Send. Flow control signal.
Request to Send. Flow control signal.
Receive. Receive input. Typically connects to a transceiver that meets the electrical requirements of
the device being communicated with.
Transmit. Transmit output. Typically connects to a transceiver that meets the electrical requirements
of the device being communicated with.
Clock/Crystal Input. This clock input is multiplied by a PLL to form the USB clock. See data sheet
specifications for frequency/tolerance information.
Data –. Bidirectional differential data line
Data +. Bidirectional differential data line
OTG ID. Senses whether the controller is a host or device. This signal is pulled low when an A-type
plug is sensed (signifying that the USB controller is the A device), but the input is high when a B-type
plug is sensed (signifying that the USB controller is the B device).
VBUS Control. Controls an external voltage source to supply VBUS when in host mode. May be
configured as open-drain. Polarity is configurable as well.
Bus Voltage. Connects to bus voltage in host and device modes.
Crystal. Drives an external crystal. Must be left unconnected if an external clock is driving USB_CLKIN.
Rev. PrG |
Page 29 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
349-BALL CSP_BGA SIGNAL DESCRIPTIONS
The processor’s pin definitions are shown in Table 12. The columns in this table provide the following information:
• Signal Name: The Signal Name column in the table
includes the signal name for every pin and (where applicable) the GPIO multiplexed pin function for every pin.
• Description: The Description column in the table provides
a verbose (descriptive) name for the signal.
• General-Purpose Port: The Port column in the table shows
whether or not the signal is multiplexed with other signals
on a general-purpose I/O port pin.
• Pin Name: The Pin Name column in the table identifies the
name of the package pin (at power on reset) on which the
signal is located (if a single function pin) or is multiplexed
(if a general-purpose I/O pin).
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions
Signal Name
ACM0_A0
ACM0_A1
ACM0_A2
ACM0_A3
ACM0_A4
ACM0_T0
C1_FLG0
C1_FLG1
C1_FLG2
C1_FLG3
C2_FLG0
C2_FLG1
C2_FLG2
C2_FLG3
CAN0_RX
CAN0_TX
CAN1_RX
CAN1_TX
CNT0_DG
CNT0_UD
CNT0_ZM
DAI0_PIN01
DAI0_PIN02
DAI0_PIN03
DAI0_PIN04
DAI0_PIN05
DAI0_PIN06
DAI0_PIN07
DAI0_PIN08
DAI0_PIN09
DAI0_PIN10
DAI0_PIN11
DAI0_PIN12
DAI0_PIN19
DAI0_PIN20
DAI1_PIN01
DAI1_PIN02
DAI1_PIN03
Description
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 External Trigger n
SHARC Core 1 Flag Pin
SHARC Core 1 Flag Pin
SHARC Core 1 Flag Pin
SHARC Core 1 Flag Pin
SHARC Core 2 Flag Pin
SHARC Core 2 Flag Pin
SHARC Core 2 Flag Pin
SHARC Core 2 Flag Pin
CAN0 Receive
CAN0 Transmit
CAN1 Receive
CAN1 Transmit
CNT0 Count Down and Gate
CNT0 Count Up and Direction
CNT0 Count Zero Marker
DAI0 Pin 1
DAI0 Pin 2
DAI0 Pin 3
DAI0 Pin 4
DAI0 Pin 5
DAI0 Pin 6
DAI0 Pin 7
DAI0 Pin 8
DAI0 Pin 9
DAI0 Pin 10
DAI0 Pin 11
DAI0 Pin 12
DAI0 Pin 19
DAI0 Pin 20
DAI1 Pin 1
DAI1 Pin 2
DAI1 Pin 3
Rev. PrG |
Port
C
C
C
D
D
C
E
E
E
E
E
E
E
E
C
C
B
B
B
B
B
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Page 30 of 168 |
June 2016
Pin Name
PC_13
PC_14
PC_15
PD_00
PD_01
PC_12
PE_01
PE_03
PE_05
PE_07
PE_02
PE_04
PE_06
PE_08
PC_07
PC_08
PB_10
PB_09
PB_14
PB_12
PB_11
DAI0_PIN01
DAI0_PIN02
DAI0_PIN03
DAI0_PIN04
DAI0_PIN05
DAI0_PIN06
DAI0_PIN07
DAI0_PIN08
DAI0_PIN09
DAI0_PIN10
DAI0_PIN11
DAI0_PIN12
DAI0_PIN19
DAI0_PIN20
DAI1_PIN01
DAI1_PIN02
DAI1_PIN03
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
DAI1_PIN04
DAI1_PIN05
DAI1_PIN06
DAI1_PIN07
DAI1_PIN08
DAI1_PIN09
DAI1_PIN10
DAI1_PIN11
DAI1_PIN12
DAI1_PIN19
DAI1_PIN20
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_A14
DMC0_A15
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
Description
DAI1 Pin 4
DAI1 Pin 5
DAI1 Pin 6
DAI1 Pin 7
DAI1 Pin 8
DAI1 Pin 9
DAI1 Pin 10
DAI1 Pin 11
DAI1 Pin 12
DAI1 Pin 19
DAI1 Pin 20
DMC0 Address 0
DMC0 Address 1
DMC0 Address 2
DMC0 Address 3
DMC0 Address 4
DMC0 Address 5
DMC0 Address 6
DMC0 Address 7
DMC0 Address 8
DMC0 Address 9
DMC0 Address 10
DMC0 Address 11
DMC0 Address 12
DMC0 Address 13
DMC0 Address 14
DMC0 Address 15
DMC0 Bank Address 0
DMC0 Bank Address 1
DMC0 Bank Address 2
DMC0 Column Address Strobe
DMC0 Clock
DMC0 Clock enable
DMC0 Clock (complement)
DMC0 Chip Select 0
DMC0 Data 0
DMC0 Data 1
DMC0 Data 2
DMC0 Data 3
DMC0 Data 4
DMC0 Data 5
DMC0 Data 6
DMC0 Data 7
DMC0 Data 8
DMC0 Data 9
DMC0 Data 10
DMC0 Data 11
DMC0 Data 12
Rev. PrG |
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Page 31 of 168 |
June 2016
Pin Name
DAI1_PIN04
DAI1_PIN05
DAI1_PIN06
DAI1_PIN07
DAI1_PIN08
DAI1_PIN09
DAI1_PIN10
DAI1_PIN11
DAI1_PIN12
DAI1_PIN19
DAI1_PIN20
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_A14
DMC0_A15
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_RESET
DMC0_RZQ
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_VREF
DMC0_WE
ETH0_CRS
ETH0_MDC
ETH0_MDIO
ETH0_PTPAUXIN0
ETH0_PTPAUXIN1
ETH0_PTPAUXIN2
ETH0_PTPAUXIN3
ETH0_PTPCLKIN0
ETH0_PTPPPS0
ETH0_PTPPPS1
ETH0_PTPPPS2
ETH0_PTPPPS3
ETH0_RXCLK_REFCLK
ETH0_RXCTL_CRS
ETH0_RXD0
ETH0_RXD1
ETH0_RXD2
ETH0_RXD3
ETH0_TXCLK
ETH0_TXCTL_TXEN
ETH0_TXD0
ETH0_TXD1
ETH0_TXD2
ETH0_TXD3
ETH0_TXEN
HADC0_VIN0
HADC0_VIN1
HADC0_VIN2
HADC0_VIN3
HADC0_VIN4
HADC0_VIN5
HADC0_VIN6
HADC0_VIN7
Description
DMC0 Data 13
DMC0 Data 14
DMC0 Data 15
DMC0 Data Mask for Lower Byte
DMC0 Data Strobe for Lower Byte
DMC0 Data Strobe for Lower Byte (complement)
DMC0 On-die termination
DMC0 Row Address Strobe
DMC0 Reset (DDR3 only)
DMC0 External calibration resistor connection
DMC0 Data Mask for Upper Byte
DMC0 Data Strobe for Upper Byte
DMC0 Data Strobe for Upper Byte (complement)
DMC0 Voltage Reference
DMC0 Write Enable
ETH0 Carrier Sense/RMII Receive Data Valid
ETH0 Management Channel Clock
ETH0 Management Channel Serial Data
ETH0 PTP Auxiliary Trigger Input 0
ETH0 PTP Auxiliary Trigger Input 1
ETH0 PTP Auxiliary Trigger Input 2
ETH0 PTP Auxiliary Trigger Input 3
ETH0 PTP Clock Input 0
ETH0 PTP Pulse-Per-Second Output 0
ETH0 PTP Pulse-Per-Second Output 1
ETH0 PTP Pulse-Per-Second Output 2
ETH0 PTP Pulse-Per-Second Output 3
ETH0 RXCLK (GigE) or REFCLK (10/100)
ETH0 RXCTL (GigE) or CRS (10/100)
ETH0 Receive Data 0
ETH0 Receive Data 1
ETH0 Receive Data 2
ETH0 Receive Data 3
ETH0 Transmit Clock
ETH0 TXCTL (GigE) or TXEN (10/100)
ETH0 Transmit Data 0
ETH0 Transmit Data 1
ETH0 Transmit Data 2
ETH0 Transmit Data 3
ETH0 Transmit Enable
HADC0 Analog Input at channel 0
HADC0 Analog Input at channel 1
HADC0 Analog Input at channel 2
HADC0 Analog Input at channel 3
HADC0 Analog Input at channel 4
HADC0 Analog Input at channel 5
HADC0 Analog Input at channel 6
HADC0 Analog Input at channel 7
Rev. PrG |
Page 32 of 168 |
June 2016
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
A
A
A
B
B
B
B
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Pin Name
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_RESET
DMC0_RZQ
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_VREF
DMC0_WE
PA_07
PA_02
PA_03
PB_03
PB_04
PB_05
PB_06
PB_02
PB_01
PB_00
PA_15
PA_14
PA_06
PA_07
PA_04
PA_05
PA_08
PA_09
PA_11
PA_10
PA_00
PA_01
PA_12
PA_13
PA_10
HADC0_VIN0
HADC0_VIN1
HADC0_VIN2
HADC0_VIN3
HADC0_VIN4
HADC0_VIN5
HADC0_VIN6
HADC0_VIN7
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
HADC0_VREFN
HADC0_VREFP
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
LP0_ACK
LP0_CLK
LP0_D0
LP0_D1
LP0_D2
LP0_D3
LP0_D4
LP0_D5
LP0_D6
LP0_D7
LP1_ACK
LP1_CLK
LP1_D0
LP1_D1
LP1_D2
LP1_D3
LP1_D4
LP1_D5
LP1_D6
LP1_D7
MLB0_CLKN
MLB0_CLKP
MLB0_DATN
MLB0_DATP
MLB0_SIGN
MLB0_SIGP
MLB0_CLK
MLB0_DAT
MLB0_SIG
MLB0_CLKOUT
PA_00-15
PB_00-15
PC_00-15
PD_00-15
PE_00-15
PPI0_CLK
PPI0_D00
PPI0_D01
PPI0_D02
PPI0_D03
PPI0_D04
Description
HADC0 Ground Reference for ADC
HADC0 External Reference for ADC
TAPC JTAG Clock
TAPC JTAG Serial Data In
TAPC JTAG Serial Data Out
TAPC JTAG Mode Select
TAPC JTAG Reset
LP0 Acknowledge
LP0 Clock
LP0 Data 0
LP0 Data 1
LP0 Data 2
LP0 Data 3
LP0 Data 4
LP0 Data 5
LP0 Data 6
LP0 Data 7
LP1 Acknowledge
LP1 Clock
LP1 Data 0
LP1 Data 1
LP1 Data 2
LP1 Data 3
LP1 Data 4
LP1 Data 5
LP1 Data 6
LP1 Data 7
MLB0 Differential Clock (–)
MLB0 Differential Clock (+)
MLB0 Differential Data (–)
MLB0 Differential Data (+)
MLB0 Differential Signal (–)
MLB0 Differential Signal (+)
MLB0 Single-Ended Clock
MLB0 Single-Ended Data
MLB0 Single-Ended Signal
MLB0 Single-Ended Clock Out
PORTA Position 00 through Position 15
PORTB Position 00 through Position 15
PORTC Position 00 through Position 15
PORTD Position 00 through Position 15
PORTE Position 00 through Position 15
EPPI0 Clock
EPPI0 Data 0
EPPI0 Data 1
EPPI0 Data 2
EPPI0 Data 3
EPPI0 Data 4
Rev. PrG |
Page 33 of 168 |
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
D
D
D
D
D
D
D
D
D
D
B
C
B
B
B
B
B
B
B
B
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
B
B
B
D
A
B
C
D
E
E
E
E
E
E
E
June 2016
Pin Name
HADC0_VREFN
HADC0_VREFP
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
PD_11
PD_10
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PB_15
PC_00
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
MLB0_CLKN
MLB0_CLKP
MLB0_DATN
MLB0_DATP
MLB0_SIGN
MLB0_SIGP
PB_04
PB_06
PB_05
PD_14
PA_00-15
PB_00-15
PC_00-15
PD_00-15
PE_00-15
PE_03
PE_12
PE_11
PE_10
PE_09
PE_08
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
PPI0_D05
PPI0_D06
PPI0_D07
PPI0_D08
PPI0_D09
PPI0_D10
PPI0_D11
PPI0_D12
PPI0_D13
PPI0_D14
PPI0_D15
PPI0_D16
PPI0_D17
PPI0_D18
PPI0_D19
PPI0_D20
PPI0_D21
PPI0_D22
PPI0_D23
PPI0_FS1
PPI0_FS2
PPI0_FS3
PWM0_AH
PWM0_AL
PWM0_BH
PWM0_BL
PWM0_CH
PWM0_CL
PWM0_DH
PWM0_DL
PWM0_SYNC
PWM0_TRIP0
PWM1_AH
PWM1_AL
PWM1_BH
PWM1_BL
PWM1_CH
PWM1_CL
PWM1_DH
PWM1_DL
PWM1_SYNC
PWM1_TRIP0
PWM2_CH
PWM2_CL
PWM2_DH
PWM2_DL
PWM2_SYNC
PWM2_TRIP0
Description
EPPI0 Data 5
EPPI0 Data 6
EPPI0 Data 7
EPPI0 Data 8
EPPI0 Data 9
EPPI0 Data 10
EPPI0 Data 11
EPPI0 Data 12
EPPI0 Data 13
EPPI0 Data 14
EPPI0 Data 15
EPPI0 Data 16
EPPI0 Data 17
EPPI0 Data 18
EPPI0 Data 19
EPPI0 Data 20
EPPI0 Data 21
EPPI0 Data 22
EPPI0 Data 23
EPPI0 Frame Sync 1 (HSYNC)
EPPI0 Frame Sync 2 (VSYNC)
EPPI0 Frame Sync 3 (FIELD)
PWM0 Channel A High Side
PWM0 Channel A Low Side
PWM0 Channel B High Side
PWM0 Channel B Low Side
PWM0 Channel C High Side
PWM0 Channel C Low Side
PWM0 Channel D High Side
PWM0 Channel D Low Side
PWM0 PWMTMR Grouped
PWM0 Shutdown Input 0
PWM1 Channel A High Side
PWM1 Channel A Low Side
PWM1 Channel B High Side
PWM1 Channel B Low Side
PWM1 Channel C High Side
PWM1 Channel C Low Side
PWM1 Channel D High Side
PWM1 Channel D Low Side
PWM1 PWMTMR Grouped
PWM1 Shutdown Input 0
PWM2 Channel C High Side
PWM2 Channel C Low Side
PWM2 Channel D High Side
PWM2 Channel D Low Side
PWM2 PWMTMR Grouped
PWM2 Shutdown Input 0
Rev. PrG |
Port
E
E
E
E
E
D
D
B
B
B
B
B
B
D
D
E
E
E
D
E
E
C
B
B
B
C
B
B
B
B
E
B
D
D
D
D
D
D
D
D
D
D
D
E
E
E
E
D
Page 34 of 168 |
June 2016
Pin Name
PE_07
PE_06
PE_05
PE_04
PE_00
PD_15
PD_14
PB_04
PB_05
PB_00
PB_01
PB_02
PB_03
PD_13
PD_12
PE_13
PE_14
PE_15
PD_00
PE_02
PE_01
PC_15
PB_07
PB_08
PB_06
PC_00
PB_13
PB_14
PB_11
PB_12
PE_09
PB_15
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PD_10
PD_11
PD_02
PD_15
PE_00
PE_04
PE_10
PE_05
PD_14
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
GND
VDD_EXT
VDD_INT
SINC0_CLK0
SINC0_D0
SINC0_D1
SINC0_D2
SINC0_D3
SMC0_A01
SMC0_A02
SMC0_A03
SMC0_A04
SMC0_A05
SMC0_A06
SMC0_A07
SMC0_A08
SMC0_A09
SMC0_A10
SMC0_A11
SMC0_A12
SMC0_A13
SMC0_A14
SMC0_A15
SMC0_A16
SMC0_A17
SMC0_A18
SMC0_A19
SMC0_A20
SMC0_A21
SMC0_A22
SMC0_A23
SMC0_A24
SMC0_A25
SMC0_ABE0
SMC0_ABE1
SMC0_AMS0
SMC0_AMS1
SMC0_AMS2
SMC0_AMS3
SMC0_AOE
SMC0_ARDY
SMC0_ARE
SMC0_AWE
SMC0_D00
SMC0_D01
SMC0_D02
SMC0_D03
SMC0_D04
Description
Ground
External Voltage Domain
Internal Voltage Domain
SINC0 Clock 0
SINC0 Data 0
SINC0 Data 1
SINC0 Data 2
SINC0 Data 3
SMC0 Address 1
SMC0 Address 2
SMC0 Address 3
SMC0 Address 4
SMC0 Address 5
SMC0 Address 6
SMC0 Address 7
SMC0 Address 8
SMC0 Address 9
SMC0 Address 10
SMC0 Address 11
SMC0 Address 12
SMC0 Address 13
SMC0 Address 14
SMC0 Address 15
SMC0 Address 16
SMC0 Address 17
SMC0 Address 18
SMC0 Address 19
SMC0 Address 20
SMC0 Address 21
SMC0 Address 22
SMC0 Address 23
SMC0 Address 24
SMC0 Address 25
SMC0 Byte Enable 0
SMC0 Byte Enable 1
SMC0 Memory Select 0
SMC0 Memory Select 1
SMC0 Memory Select 2
SMC0 Memory Select 3
SMC0 Output Enable
SMC0 Asynchronous Ready
SMC0 Read Enable
SMC0 Write Enable
SMC0 Data 0
SMC0 Data 1
SMC0 Data 2
SMC0 Data 3
SMC0 Data 4
Rev. PrG |
Port
Not Muxed
Not Muxed
Not Muxed
B
A
A
B
B
B
B
B
B
D
D
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
C
E
E
C
E
C
C
D
B
C
B
E
E
E
E
E
Page 35 of 168 |
June 2016
Pin Name
GND
VDD_EXT
VDD_INT
PB_01
PA_14
PA_15
PB_00
PB_04
PB_05
PB_06
PB_03
PB_02
PD_13
PD_12
PB_01
PB_00
PA_15
PA_14
PA_09
PA_08
PA_13
PA_12
PA_11
PA_07
PA_06
PA_05
PA_04
PA_01
PA_00
PA_10
PA_03
PA_02
PC_12
PE_14
PE_15
PC_15
PE_13
PC_07
PC_08
PD_01
PB_04
PC_00
PB_15
PE_12
PE_11
PE_10
PE_09
PE_00
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
SMC0_D05
SMC0_D06
SMC0_D07
SMC0_D08
SMC0_D09
SMC0_D10
SMC0_D11
SMC0_D12
SMC0_D13
SMC0_D14
SMC0_D15
SPI0_CLK
SPI0_MISO
SPI0_MOSI
SPI0_RDY
SPI0_SEL1
SPI0_SEL2
SPI0_SEL3
SPI0_SEL4
SPI0_SEL5
SPI0_SEL6
SPI0_SEL7
SPI0_SS
SPI1_CLK
SPI1_MISO
SPI1_MOSI
SPI1_RDY
SPI1_SEL1
SPI1_SEL2
SPI1_SEL3
SPI1_SEL4
SPI1_SEL5
SPI1_SS
SPI2_CLK
SPI2_D2
SPI2_D3
SPI2_MISO
SPI2_MOSI
SPI2_RDY
SPI2_SEL1
SPI2_SEL2
SPI2_SEL3
SPI2_SEL4
SPI2_SEL5
SPI2_SS
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
Description
SMC0 Data 5
SMC0 Data 6
SMC0 Data 7
SMC0 Data 8
SMC0 Data 9
SMC0 Data 10
SMC0 Data 11
SMC0 Data 12
SMC0 Data 13
SMC0 Data 14
SMC0 Data 15
SPI0 Clock
SPI0 Master In, Slave Out
SPI0 Master Out, Slave In
SPI0 Ready
SPI0 Slave Select Output 1
SPI0 Slave Select Output 2
SPI0 Slave Select Output 3
SPI0 Slave Select Output 4
SPI0 Slave Select Output 5
SPI0 Slave Select Output 6
SPI0 Slave Select Output 7
SPI0 Slave Select Input
SPI1 Clock
SPI1 Master In, Slave Out
SPI1 Master Out, Slave In
SPI1 Ready
SPI1 Slave Select Output 1
SPI1 Slave Select Output 2
SPI1 Slave Select Output 3
SPI1 Slave Select Output 4
SPI1 Slave Select Output 5
SPI1 Slave Select Input
SPI2 Clock
SPI2 Data 2
SPI2 Data 3
SPI2 Master In, Slave Out
SPI2 Master Out, Slave In
SPI2 Ready
SPI2 Slave Select Output 1
SPI2 Slave Select Output 2
SPI2 Slave Select Output 3
SPI2 Slave Select Output 4
SPI2 Slave Select Output 5
SPI2 Slave Select Input
Boot Mode Control n
Boot Mode Control n
Boot Mode Control n
Rev. PrG |
Port
D
D
D
B
B
B
B
B
B
B
B
C
C
C
C
C
D
C
C
E
E
E
D
E
E
E
E
C
E
E
E
E
E
C
C
C
C
C
E
C
E
E
E
E
C
Not Muxed
Not Muxed
Not Muxed
Page 36 of 168 |
June 2016
Pin Name
PD_15
PD_14
PD_00
PB_14
PB_13
PB_12
PB_11
PB_10
PB_09
PB_08
PB_07
PC_09
PC_10
PC_11
PC_12
PC_07
PD_01
PC_12
PC_00
PE_01
PE_02
PE_03
PD_01
PE_13
PE_14
PE_15
PE_08
PC_13
PE_07
PE_11
PE_12
PE_08
PE_11
PC_01
PC_04
PC_05
PC_02
PC_03
PE_12
PC_06
PE_03
PE_04
PE_05
PE_06
PC_06
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
SYS_FAULT
SYS_FAULT
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
TM0_ACI0
TM0_ACI1
TM0_ACI2
TM0_ACI3
TM0_ACI4
TM0_ACLK1
TM0_ACLK2
TM0_ACLK3
TM0_ACLK4
TM0_CLK
TM0_TMR0
TM0_TMR1
TM0_TMR2
TM0_TMR3
TM0_TMR4
TM0_TMR5
TRACE0_CLK
TRACE0_D00
TRACE0_D01
TRACE0_D02
TRACE0_D03
TRACE0_D04
TRACE0_D05
TRACE0_D06
TRACE0_D07
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
TWI2_SCL
TWI2_SDA
UART0_CTS
UART0_RTS
UART0_RX
UART0_TX
UART1_CTS
UART1_RTS
UART1_RX
UART1_TX
Description
Clock/Crystal Input
Clock/Crystal Input
Processor Clock Output
Active-High Fault Output
Active-Low Fault Output
Processor Hardware Reset Control
Reset Output
Crystal Output
Crystal Output
TIMER0 Alternate Capture Input 0
TIMER0 Alternate Capture Input 1
TIMER0 Alternate Capture Input 2
TIMER0 Alternate Capture Input 3
TIMER0 Alternate Capture Input 4
TIMER0 Alternate Clock 1
TIMER0 Alternate Clock 2
TIMER0 Alternate Clock 3
TIMER0 Alternate Clock 4
TIMER0 Clock
TIMER0 Timer 0
TIMER0 Timer 1
TIMER0 Timer 2
TIMER0 Timer 3
TIMER0 Timer 4
TIMER0 Timer 5
TRACE0 Trace Clock
TRACE0 Trace Data 0
TRACE0 Trace Data 1
TRACE0 Trace Data 2
TRACE0 Trace Data 3
TRACE0 Trace Data 4
TRACE0 Trace Data 5
TRACE0 Trace Data 6
TRACE0 Trace Data 7
TWI0 Serial Clock
TWI0 Serial Data
TWI1 Serial Clock
TWI1 Serial Data
TWI2 Serial Clock
TWI2 Serial Data
UART0 Clear to Send
UART0 Request to Send
UART0 Receive
UART0 Transmit
UART1 Clear to Send
UART1 Request to Send
UART1 Receive
UART1 Transmit
Rev. PrG |
Page 37 of 168 |
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
C
B
D
C
B
D
D
B
B
C
E
B
B
B
B
B
D
D
D
D
D
D
D
D
D
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
D
C
C
C
E
E
B
B
June 2016
Pin Name
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
SYS_FAULT
SYS_FAULT
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
PC_14
PB_03
PD_13
PC_07
PB_10
PD_08
PD_09
PB_00
PB_01
PC_11
PE_09
PB_15
PB_10
PB_07
PB_08
PB_14
PD_10
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
TWI2_SCL
TWI2_SDA
PD_00
PC_15
PC_14
PC_13
PE_01
PE_02
PB_03
PB_02
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 12. ADSP-SC58x/ADSP-2158x 349-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
UART2_CTS
UART2_RTS
UART2_RX
UART2_TX
USB0_CLKIN
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
USB0_XTAL
VDD_DMC
VDD_HADC
VDD_USB
Description
UART2 Clear to Send
UART2 Request to Send
UART2 Receive
UART2 Transmit
USB0 Clock/Crystal Input
USB0 Data –
USB0 Data +
USB0 OTG ID
USB0 VBUS Control
USB0 Bus Voltage
USB0 Crystal
DMC VDD
HADC VDD
USB VDD
Rev. PrG |
Port
E
E
D
D
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Page 38 of 168 |
June 2016
Pin Name
PE_11
PE_10
PD_13
PD_12
USB_CLKIN
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
USB_XTAL
VDD_DMC
VDD_HADC
VDD_USB
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
GPIO MULTIPLEXING FOR 349-BALL CSP_BGA
Table 13 through Table 17 identify the pin functions that are
multiplexed on the general-purpose I/O pins of the 349-ball
CSP_BGA package.
Table 13. Signal Multiplexing for Port A
Signal Name
PA_00
PA_01
PA_02
PA_03
PA_04
PA_05
PA_06
PA_07
PA_08
PA_09
PA_10
PA_11
PA_12
PA_13
PA_14
PA_15
Multiplexed
Function 0
ETH0_TXD0
ETH0_TXD1
ETH0_MDC
ETH0_MDIO
ETH0_RXD0
ETH0_RXD1
ETH0_RXCLK_REFCLK
ETH0_CRS
ETH0_RXD2
ETH0_RXD3
ETH0_TXEN
ETH0_TXCLK
ETH0_TXD2
ETH0_TXD3
ETH0_PTPPPS3
ETH0_PTPPPS2
Multiplexed
Function 1
Multiplexed
Function 2
Multiplexed
Function 3
SMC0_A21
SMC0_A20
SMC0_A24
SMC0_A23
SMC0_A19
SMC0_A18
SMC0_A17
SMC0_A16
SMC0_A12
SMC0_A11
SMC0_A22
SMC0_A15
SMC0_A14
SMC0_A13
SMC0_A10
SMC0_A09
Multiplexed
Function Input Tap
Multiplexed
Function 2
PPI0_D14
PPI0_D15
PPI0_D16
PPI0_D17
PPI0_D12
PPI0_D13
PWM0_BH
TM0_TMR3
TM0_TMR4
CAN1_TX
CAN1_RX
PWM0_DH
PWM0_DL
PWM0_CH
PWM0_CL
TM0_TMR1
Multiplexed
Function 3
SMC0_A08
SMC0_A07
SMC0_A04
SMC0_A03
SMC0_ARDY
SMC0_A01
SMC0_A02
SMC0_D15
SMC0_D14
SMC0_D13
SMC0_D12
SMC0_D11
SMC0_D10
SMC0_D09
SMC0_D08
SMC0_AWE
Multiplexed
Function Input Tap
TM0_ACLK3
TM0_ACLK4
SINC0_D0
SINC0_D1
Table 14. Signal Multiplexing for Port B
Signal Name
PB_00
PB_01
PB_02
PB_03
PB_04
PB_05
PB_06
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
PB_15
Multiplexed
Function 0
ETH0_PTPPPS1
ETH0_PTPPPS0
ETH0_PTPCLKIN0
ETH0_PTPAUXIN0
MLB0_CLK
MLB0_SIG
MLB0_DAT
LP1_D0
LP1_D1
LP1_D2
LP1_D3
LP1_D4
LP1_D5
LP1_D6
LP1_D7
LP1_ACK
Multiplexed
Function 1
SINC0_D2
SINC0_CLK0
UART1_TX
UART1_RX
SINC0_D3
PWM0_AH
PWM0_AL
TM0_TMR2
TM0_TMR5
PWM0_TRIP0
Rev. PrG |
Page 39 of 168 |
June 2016
TM0_ACI1
ETH0_PTPAUXIN1
ETH0_PTPAUXIN2
ETH0_PTPAUXIN3
TM0_ACI4
CNT0_ZM
CNT0_UD
CNT0_DG
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 15. Signal Multiplexing for Port C
Signal Name
PC_00
PC_01
PC_02
PC_03
PC_04
PC_05
PC_06
PC_07
PC_08
PC_09
PC_10
PC_11
PC_12
PC_13
PC_14
PC_15
Multiplexed
Function 0
LP1_CLK
SPI2_CLK
SPI2_MISO
SPI2_MOSI
SPI2_D2
SPI2_D3
SPI2_SEL1
CAN0_RX
CAN0_TX
SPI0_CLK
SPI0_MISO
SPI0_MOSI
SPI0_SEL3
UART0_TX
UART0_RX
UART0_RTS
Multiplexed
Function 1
PWM0_BL
Multiplexed
Function 2
SPI0_SEL4
SPI0_SEL1
Multiplexed
Function 3
SMC0_ARE
SMC0_AMS2
SMC0_AMS3
Multiplexed
Function Input Tap
SPI2_SS
TM0_ACI3
TM0_CLK
SPI0_RDY
SPI1_SEL1
PPI0_FS3
ACM0_T0
ACM0_A0
ACM0_A1
ACM0_A2
SMC0_A25
Multiplexed
Function 2
ACM0_A3
ACM0_A4
TRACE0_D00
TRACE0_D01
TRACE0_D02
TRACE0_D03
TRACE0_D04
TRACE0_D05
TRACE0_D06
TRACE0_D07
TRACE0_CLK
Multiplexed
Function 3
SMC0_D07
SMC0_AOE
PPI0_D19
PPI0_D18
MLB0_CLKOUT
SMC0_A06
SMC0_A05
SMC0_D06
SMC0_D05
TM0_ACI0
SMC0_AMS0
Table 16. Signal Multiplexing for Port D
Signal Name
PD_00
PD_01
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PD_10
PD_11
PD_12
PD_13
PD_14
PD_15
Multiplexed
Function 0
UART0_CTS
SPI0_SEL2
LP0_D0
LP0_D1
LP0_D2
LP0_D3
LP0_D4
LP0_D5
LP0_D6
LP0_D7
LP0_CLK
LP0_ACK
UART2_TX
UART2_RX
PPI0_D11
PPI0_D10
Multiplexed
Function 1
PPI0_D23
PWM1_TRIP0
PWM1_AH
PWM1_AL
PWM1_BH
PWM1_BL
PWM1_CH
PWM1_CL
PWM1_DH
PWM1_DL
PWM1_SYNC
PWM2_TRIP0
PWM2_CH
Rev. PrG |
Page 40 of 168 |
June 2016
Multiplexed
Function Input Tap
SPI0_SS
TM0_ACLK1
TM0_ACLK2
TM0_ACI2
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 17. Signal Multiplexing for Port E
Signal Name
PE_00
PE_01
PE_02
PE_03
PE_04
PE_05
PE_06
PE_07
PE_08
PE_09
PE_10
PE_11
PE_12
PE_13
PE_14
PE_15
Multiplexed
Function 0
PPI0_D09
PPI0_FS2
PPI0_FS1
PPI0_CLK
PPI0_D08
PPI0_D07
PPI0_D06
PPI0_D05
PPI0_D04
PPI0_D03
PPI0_D02
PPI0_D01
PPI0_D00
SPI1_CLK
SPI1_MISO
SPI1_MOSI
Multiplexed
Function 1
PWM2_CL
SPI0_SEL5
SPI0_SEL6
SPI0_SEL7
PWM2_DH
PWM2_SYNC
SPI1_SEL5
PWM0_SYNC
PWM2_DL
SPI1_SEL3
SPI1_SEL4
Multiplexed
Function 2
UART1_CTS
UART1_RTS
SPI2_SEL2
SPI2_SEL3
SPI2_SEL4
SPI2_SEL5
SPI1_SEL2
SPI1_RDY
TM0_TMR0
UART2_RTS
UART2_CTS
SPI2_RDY
PPI0_D20
PPI0_D21
PPI0_D22
Table 18 shows the internal timer signal routing. This table
applies to both the 349-ball and 529-ball CSP_BGA packages.
Table 18. Internal Timer Signal Routing
Timer Input Signal
TM0_ACLK0
TM0_ACI5
TM0_ACLK5
TM0_ACI6
TM0_ACLK6
TM0_ACI7
TM0_ACLK7
Internal Source
SYS_CLKIN1
DAI0_CRS_PB04_O
DAI0_CRS_PB03_O
DAI1_CRS_PB04_O
DAI1_CRS_PB03_O
CNT0_TO
SYS_CLKIN0
Rev. PrG |
Page 41 of 168 |
June 2016
Multiplexed
Function 3
SMC0_D04
C1_FLG0
C2_FLG0
C1_FLG1
C2_FLG1
C1_FLG2
C2_FLG2
C1_FLG3
C2_FLG3
SMC0_D03
SMC0_D02
SMC0_D01
SMC0_D00
SMC0_AMS1
SMC0_ABE0
SMC0_ABE1
Multiplexed
Function Input Tap
SPI1_SS
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
529-BALL CSP_BGA SIGNAL DESCRIPTIONS
The processor’s pin definitions are shown Table 19. The columns in this table provide the following information:
• Signal Name: The Signal Name column in the table
includes the signal name for every pin and (where applicable) the GPIO multiplexed pin function for every pin.
• Description: The Description column in the table provides
a verbose (descriptive) name for the signal.
• General-Purpose Port: The Port column in the table shows
whether or not the signal is multiplexed with other signals
on a general-purpose I/O port pin.
• Pin Name: The Pin Name column in the table identifies the
name of the package pin (at power on reset) on which the
signal is located (if a single function pin) or is multiplexed
(if a general-purpose I/O pin).
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions
Signal Name
ACM0_A0
ACM0_A1
ACM0_A2
ACM0_A3
ACM0_A4
ACM0_T0
C1_FLG0
C1_FLG1
C1_FLG2
C1_FLG3
C2_FLG0
C2_FLG1
C2_FLG2
C2_FLG3
CAN0_RX
CAN0_TX
CAN1_RX
CAN1_TX
CNT0_DG
CNT0_UD
CNT0_ZM
DAI0_PIN01
DAI0_PIN02
DAI0_PIN03
DAI0_PIN04
DAI0_PIN05
DAI0_PIN06
DAI0_PIN07
DAI0_PIN08
DAI0_PIN09
DAI0_PIN10
DAI0_PIN11
DAI0_PIN12
DAI0_PIN13
DAI0_PIN14
DAI0_PIN15
DAI0_PIN16
DAI0_PIN17
Description
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 ADC Control Signals
ACM0 External Trigger n
SHARC Core 1 Flag Pin
SHARC Core 1 Flag Pin
SHARC Core 1 Flag Pin
SHARC Core 1 Flag Pin
SHARC Core 2 Flag Pin
SHARC Core 2 Flag Pin
SHARC Core 2 Flag Pin
SHARC Core 2 Flag Pin
CAN0 Receive
CAN0 Transmit
CAN1 Receive
CAN1 Transmit
CNT0 Count Down and Gate
CNT0 Count Up and Direction
CNT0 Count Zero Marker
DAI0 Pin 1
DAI0 Pin 2
DAI0 Pin 3
DAI0 Pin 4
DAI0 Pin 5
DAI0 Pin 6
DAI0 Pin 7
DAI0 Pin 8
DAI0 Pin 9
DAI0 Pin 10
DAI0 Pin 11
DAI0 Pin 12
DAI0 Pin 13
DAI0 Pin 14
DAI0 Pin 15
DAI0 Pin 16
DAI0 Pin 17
Rev. PrG |
Port
C
C
C
D
D
C
E
E
E
E
E
E
E
E
C
C
B
B
B
B
B
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Page 42 of 168 |
June 2016
Pin Name
PC_13
PC_14
PC_15
PD_00
PD_01
PC_12
PE_01
PE_03
PE_05
PE_07
PE_02
PE_04
PE_06
PE_08
PC_07
PC_08
PB_10
PB_09
PB_14
PB_12
PB_11
DAI0_PIN01
DAI0_PIN02
DAI0_PIN03
DAI0_PIN04
DAI0_PIN05
DAI0_PIN06
DAI0_PIN07
DAI0_PIN08
DAI0_PIN09
DAI0_PIN10
DAI0_PIN11
DAI0_PIN12
DAI0_PIN13
DAI0_PIN14
DAI0_PIN15
DAI0_PIN16
DAI0_PIN17
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
DAI0_PIN18
DAI0_PIN19
DAI0_PIN20
DAI1_PIN01
DAI1_PIN02
DAI1_PIN03
DAI1_PIN04
DAI1_PIN05
DAI1_PIN06
DAI1_PIN07
DAI1_PIN08
DAI1_PIN09
DAI1_PIN10
DAI1_PIN11
DAI1_PIN12
DAI1_PIN13
DAI1_PIN14
DAI1_PIN15
DAI1_PIN16
DAI1_PIN17
DAI1_PIN18
DAI1_PIN19
DAI1_PIN20
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_A14
DMC0_A15
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
Description
DAI0 Pin 18
DAI0 Pin 19
DAI0 Pin 20
DAI1 Pin 1
DAI1 Pin 2
DAI1 Pin 3
DAI1 Pin 4
DAI1 Pin 5
DAI1 Pin 6
DAI1 Pin 7
DAI1 Pin 8
DAI1 Pin 9
DAI1 Pin 10
DAI1 Pin 11
DAI1 Pin 12
DAI1 Pin 13
DAI1 Pin 14
DAI1 Pin 15
DAI1 Pin 16
DAI1 Pin 17
DAI1 Pin 18
DAI1 Pin 19
DAI1 Pin 20
DMC0 Address 0
DMC0 Address 1
DMC0 Address 2
DMC0 Address 3
DMC0 Address 4
DMC0 Address 5
DMC0 Address 6
DMC0 Address 7
DMC0 Address 8
DMC0 Address 9
DMC0 Address 10
DMC0 Address 11
DMC0 Address 12
DMC0 Address 13
DMC0 Address 14
DMC0 Address 15
DMC0 Bank Address 0
DMC0 Bank Address 1
DMC0 Bank Address 2
DMC0 Column Address Strobe
DMC0 Clock
DMC0 Clock enable
DMC0 Clock (complement)
DMC0 Chip Select 0
DMC0 Data 0
Rev. PrG |
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Page 43 of 168 |
June 2016
Pin Name
DAI0_PIN18
DAI0_PIN19
DAI0_PIN20
DAI1_PIN01
DAI1_PIN02
DAI1_PIN03
DAI1_PIN04
DAI1_PIN05
DAI1_PIN06
DAI1_PIN07
DAI1_PIN08
DAI1_PIN09
DAI1_PIN10
DAI1_PIN11
DAI1_PIN12
DAI1_PIN13
DAI1_PIN14
DAI1_PIN15
DAI1_PIN16
DAI1_PIN17
DAI1_PIN18
DAI1_PIN19
DAI1_PIN20
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_A14
DMC0_A15
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_RESET
DMC0_RZQ
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_VREF
DMC0_WE
DMC1_A00
DMC1_A01
DMC1_A02
DMC1_A03
DMC1_A04
DMC1_A05
DMC1_A06
DMC1_A07
DMC1_A08
DMC1_A09
DMC1_A10
DMC1_A11
DMC1_A12
DMC1_A13
DMC1_A14
DMC1_A15
DMC1_BA0
DMC1_BA1
DMC1_BA2
DMC1_CAS
DMC1_CK
Description
DMC0 Data 1
DMC0 Data 2
DMC0 Data 3
DMC0 Data 4
DMC0 Data 5
DMC0 Data 6
DMC0 Data 7
DMC0 Data 8
DMC0 Data 9
DMC0 Data 10
DMC0 Data 11
DMC0 Data 12
DMC0 Data 13
DMC0 Data 14
DMC0 Data 15
DMC0 Data Mask for Lower Byte
DMC0 Data Strobe for Lower Byte
DMC0 Data Strobe for Lower Byte (complement)
DMC0 On-die termination
DMC0 Row Address Strobe
DMC0 Reset (DDR3 only)
DMC0 External calibration resistor connection
DMC0 Data Mask for Upper Byte
DMC0 Data Strobe for Upper Byte
DMC0 Data Strobe for Upper Byte (complement)
DMC0 Voltage Reference
DMC0 Write Enable
DMC1 Address 0
DMC1 Address 1
DMC1 Address 2
DMC1 Address 3
DMC1 Address 4
DMC1 Address 5
DMC1 Address 6
DMC1 Address 7
DMC1 Address 8
DMC1 Address 9
DMC1 Address 10
DMC1 Address 11
DMC1 Address 12
DMC1 Address 13
DMC1 Address 14
DMC1 Address 15
DMC1 Bank Address 0
DMC1 Bank Address 1
DMC1 Bank Address 2
DMC1 Column Address Strobe
DMC1 Clock
Rev. PrG |
Page 44 of 168 |
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
June 2016
Pin Name
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_RESET
DMC0_RZQ
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_VREF
DMC0_WE
DMC1_A00
DMC1_A01
DMC1_A02
DMC1_A03
DMC1_A04
DMC1_A05
DMC1_A06
DMC1_A07
DMC1_A08
DMC1_A09
DMC1_A10
DMC1_A11
DMC1_A12
DMC1_A13
DMC1_A14
DMC1_A15
DMC1_BA0
DMC1_BA1
DMC1_BA2
DMC1_CAS
DMC1_CK
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
DMC1_CKE
DMC1_CK
DMC1_CS0
DMC1_DQ00
DMC1_DQ01
DMC1_DQ02
DMC1_DQ03
DMC1_DQ04
DMC1_DQ05
DMC1_DQ06
DMC1_DQ07
DMC1_DQ08
DMC1_DQ09
DMC1_DQ10
DMC1_DQ11
DMC1_DQ12
DMC1_DQ13
DMC1_DQ14
DMC1_DQ15
DMC1_LDM
DMC1_LDQS
DMC1_LDQS
DMC1_ODT
DMC1_RAS
DMC1_RESET
DMC1_RZQ
DMC1_UDM
DMC1_UDQS
DMC1_UDQS
DMC1_VREF
DMC1_WE
ETH0_CRS
ETH0_MDC
ETH0_MDIO
ETH0_PTPAUXIN0
ETH0_PTPAUXIN1
ETH0_PTPAUXIN2
ETH0_PTPAUXIN3
ETH0_PTPCLKIN0
ETH0_PTPPPS0
ETH0_PTPPPS1
ETH0_PTPPPS2
ETH0_PTPPPS3
ETH0_RXCLK_REFCLK
ETH0_RXCTL_CRS
ETH0_RXD0
ETH0_RXD1
ETH0_RXD2
Description
DMC1 Clock enable
DMC1 Clock (complement)
DMC1 Chip Select 0
DMC1 Data 0
DMC1 Data 1
DMC1 Data 2
DMC1 Data 3
DMC1 Data 4
DMC1 Data 5
DMC1 Data 6
DMC1 Data 7
DMC1 Data 8
DMC1 Data 9
DMC1 Data 10
DMC1 Data 11
DMC1 Data 12
DMC1 Data 13
DMC1 Data 14
DMC1 Data 15
DMC1 Data Mask for Lower Byte
DMC1 Data Strobe for Lower Byte
DMC1 Data Strobe for Lower Byte (complement)
DMC1 On-die termination
DMC1 Row Address Strobe
DMC1 Reset (DDR3 only)
DMC1 External calibration resistor connection
DMC1 Data Mask for Upper Byte
DMC1 Data Strobe for Upper Byte
DMC1 Data Strobe for Upper Byte (complement)
DMC1 Voltage Reference
DMC1 Write Enable
ETH0 Carrier Sense/RMII Receive Data Valid
ETH0 Management Channel Clock
ETH0 Management Channel Serial Data
ETH0 PTP Auxiliary Trigger Input 0
ETH0 PTP Auxiliary Trigger Input 1
ETH0 PTP Auxiliary Trigger Input 2
ETH0 PTP Auxiliary Trigger Input 3
ETH0 PTP Clock Input 0
ETH0 PTP Pulse-Per-Second Output 0
ETH0 PTP Pulse-Per-Second Output 1
ETH0 PTP Pulse-Per-Second Output 2
ETH0 PTP Pulse-Per-Second Output 3
ETH0 RXCLK (GigE) or REFCLK (10/100)
ETH0 RXCTL (GigE) or CRS (10/100)
ETH0 Receive Data 0
ETH0 Receive Data 1
ETH0 Receive Data 2
Rev. PrG |
Page 45 of 168 |
Port
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
A
A
A
B
B
B
B
B
B
B
A
A
A
A
A
A
A
June 2016
Pin Name
DMC1_CKE
DMC1_CK
DMC1_CS0
DMC1_DQ00
DMC1_DQ01
DMC1_DQ02
DMC1_DQ03
DMC1_DQ04
DMC1_DQ05
DMC1_DQ06
DMC1_DQ07
DMC1_DQ08
DMC1_DQ09
DMC1_DQ10
DMC1_DQ11
DMC1_DQ12
DMC1_DQ13
DMC1_DQ14
DMC1_DQ15
DMC1_LDM
DMC1_LDQS
DMC1_LDQS
DMC1_ODT
DMC1_RAS
DMC1_RESET
DMC1_RZQ
DMC1_UDM
DMC1_UDQS
DMC1_UDQS
DMC1_VREF
DMC1_WE
PA_07
PA_02
PA_03
PB_03
PB_04
PB_05
PB_06
PB_02
PB_01
PB_00
PA_15
PA_14
PA_06
PA_07
PA_04
PA_05
PA_08
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
ETH0_RXD3
ETH0_TXCLK
ETH0_TXCTL_TXEN
ETH0_TXD0
ETH0_TXD1
ETH0_TXD2
ETH0_TXD3
ETH0_TXEN
ETH1_CRS
ETH1_MDC
ETH1_MDIO
ETH1_REFCLK
ETH1_RXD0
ETH1_RXD1
ETH1_TXD0
ETH1_TXD1
ETH1_TXEN
HADC0_EOC_DOUT
HADC0_MUX0
HADC0_MUX1
HADC0_MUX2
HADC0_VIN0
HADC0_VIN1
HADC0_VIN2
HADC0_VIN3
HADC0_VIN4
HADC0_VIN5
HADC0_VIN6
HADC0_VIN7
HADC0_VREFN
HADC0_VREFP
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
LP0_ACK
LP0_CLK
LP0_D0
LP0_D1
LP0_D2
LP0_D3
LP0_D4
LP0_D5
LP0_D6
LP0_D7
LP1_ACK
LP1_CLK
Description
ETH0 Receive Data 3
ETH0 Transmit Clock
ETH0 TXCTL (GigE) or TXEN (10/100)
ETH0 Transmit Data 0
ETH0 Transmit Data 1
ETH0 Transmit Data 2
ETH0 Transmit Data 3
ETH0 Transmit Enable
ETH1 Carrier Sense/RMII Receive Data Valid
ETH1 Management Channel Clock
ETH1 Management Channel Serial Data
ETH1 Reference Clock
ETH1 Receive Data 0
ETH1 Receive Data 1
ETH1 Transmit Data 0
ETH1 Transmit Data 1
ETH1 Transmit Enable
HADC0 End of Conversion / Serial Data Out
HADC0 Controls to external multiplexer
HADC0 Controls to external multiplexer
HADC0 Controls to external multiplexer
HADC0 Analog Input at channel 0
HADC0 Analog Input at channel 1
HADC0 Analog Input at channel 2
HADC0 Analog Input at channel 3
HADC0 Analog Input at channel 4
HADC0 Analog Input at channel 5
HADC0 Analog Input at channel 6
HADC0 Analog Input at channel 7
HADC0 Ground Reference for ADC
HADC0 External Reference for ADC
TAPC JTAG Clock
TAPC JTAG Serial Data In
TAPC JTAG Serial Data Out
TAPC JTAG Mode Select
TAPC JTAG Reset
LP0 Acknowledge
LP0 Clock
LP0 Data 0
LP0 Data 1
LP0 Data 2
LP0 Data 3
LP0 Data 4
LP0 Data 5
LP0 Data 6
LP0 Data 7
LP1 Acknowledge
LP1 Clock
Rev. PrG |
Page 46 of 168 |
Port
A
A
A
A
A
A
A
A
F
F
F
G
G
G
G
G
G
F
F
F
F
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
D
D
D
D
D
D
D
D
D
D
B
C
June 2016
Pin Name
PA_09
PA_11
PA_10
PA_00
PA_01
PA_12
PA_13
PA_10
PF_13
PF_14
PF_15
PG_00
PG_04
PG_05
PG_02
PG_03
PG_01
PF_02
PF_05
PF_04
PF_03
HADC0_VIN0
HADC0_VIN1
HADC0_VIN2
HADC0_VIN3
HADC0_VIN4
HADC0_VIN5
HADC0_VIN6
HADC0_VIN7
HADC0_VREFN
HADC0_VREFP
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
PD_11
PD_10
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PB_15
PC_00
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
LP1_D0
LP1_D1
LP1_D2
LP1_D3
LP1_D4
LP1_D5
LP1_D6
LP1_D7
MLB0_CLKN
MLB0_CLKP
MLB0_DATN
MLB0_DATP
MLB0_SIGN
MLB0_SIGP
MLB0_CLK
MLB0_DAT
MLB0_SIG
MLB0_CLKOUT
MSI0_CD
MSI0_CLK
MSI0_CMD
MSI0_D0
MSI0_D1
MSI0_D2
MSI0_D3
MSI0_D4
MSI0_D5
MSI0_D6
MSI0_D7
MSI0_INT
PA_00-15
PB_00-15
PCIE0_CLKM
PCIE0_CLKP
PCIE0_REF
PCIE0_RXM
PCIE0_RXP
PCIE0_TXM
PCIE0_TXP
PC_00-15
PD_00-15
PE_00-15
PF_00-15
PG_00-5
PPI0_CLK
PPI0_D00
PPI0_D01
PPI0_D02
Description
LP1 Data 0
LP1 Data 1
LP1 Data 2
LP1 Data 3
LP1 Data 4
LP1 Data 5
LP1 Data 6
LP1 Data 7
MLB0 Differential Clock (–)
MLB0 Differential Clock (+)
MLB0 Differential Data (–)
MLB0 Differential Data (+)
MLB0 Differential Signal (–)
MLB0 Differential Signal (+)
MLB0 Single-Ended Clock
MLB0 Single-Ended Data
MLB0 Single-Ended Signal
MLB0 Single-Ended Clock Out
MSI0 Card Detect
MSI0 Clock
MSI0 Command
MSI0 Data 0
MSI0 Data 1
MSI0 Data 2
MSI0 Data 3
MSI0 Data 4
MSI0 Data 5
MSI0 Data 6
MSI0 Data 7
MSI0 eSDIO Interrupt Input
PORTA Position 00 through Position 15
PORTB Position 00 through Position 15
PCIE0 CLK PCIE0 CLK +
PCIE0 Reference
PCIE0 RX PCIE0 RX +
PCIE0 TX PCIE0 TX +
PORTC Position 00 through Position 15
PORTD Position 00 through Position 15
PORTE Position 00 through Position 15
PORTF Position 00 through Position 15
PORTG Position 00 through Position 5
EPPI0 Clock
EPPI0 Data 0
EPPI0 Data 1
EPPI0 Data 2
Rev. PrG |
Page 47 of 168 |
Port
B
B
B
B
B
B
B
B
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
B
B
B
D
F
F
F
F
F
F
F
F
F
F
F
F
A
B
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
C
D
E
F
G
E
E
E
E
June 2016
Pin Name
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
MLB0_CLKN
MLB0_CLKP
MLB0_DATN
MLB0_DATP
MLB0_SIGN
MLB0_SIGP
PB_04
PB_06
PB_05
PD_14
PF_12
PF_11
PF_10
PF_02
PF_03
PF_04
PF_05
PF_06
PF_07
PF_08
PF_09
PF_13
PA_00-15
PB_00-15
PCIE0_CLKM
PCIE0_CLKP
PCIE0_REF
PCIE0_RXM
PCIE0_RXP
PCIE0_TXM
PCIE0_TXP
PC_00-15
PD_00-15
PE_00-15
PF_00-15
PG_00-5
PE_03
PE_12
PE_11
PE_10
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
PPI0_D03
PPI0_D04
PPI0_D05
PPI0_D06
PPI0_D07
PPI0_D08
PPI0_D09
PPI0_D10
PPI0_D11
PPI0_D12
PPI0_D13
PPI0_D14
PPI0_D15
PPI0_D16
PPI0_D17
PPI0_D18
PPI0_D19
PPI0_D20
PPI0_D21
PPI0_D22
PPI0_D23
PPI0_FS1
PPI0_FS2
PPI0_FS3
PWM0_AH
PWM0_AL
PWM0_BH
PWM0_BL
PWM0_CH
PWM0_CL
PWM0_DH
PWM0_DL
PWM0_SYNC
PWM0_TRIP0
PWM1_AH
PWM1_AL
PWM1_BH
PWM1_BL
PWM1_CH
PWM1_CL
PWM1_DH
PWM1_DL
PWM1_SYNC
PWM1_TRIP0
PWM2_AH
PWM2_AL
PWM2_BH
PWM2_BL
Description
EPPI0 Data 3
EPPI0 Data 4
EPPI0 Data 5
EPPI0 Data 6
EPPI0 Data 7
EPPI0 Data 8
EPPI0 Data 9
EPPI0 Data 10
EPPI0 Data 11
EPPI0 Data 12
EPPI0 Data 13
EPPI0 Data 14
EPPI0 Data 15
EPPI0 Data 16
EPPI0 Data 17
EPPI0 Data 18
EPPI0 Data 19
EPPI0 Data 20
EPPI0 Data 21
EPPI0 Data 22
EPPI0 Data 23
EPPI0 Frame Sync 1 (HSYNC)
EPPI0 Frame Sync 2 (VSYNC)
EPPI0 Frame Sync 3 (FIELD)
PWM0 Channel A High Side
PWM0 Channel A Low Side
PWM0 Channel B High Side
PWM0 Channel B Low Side
PWM0 Channel C High Side
PWM0 Channel C Low Side
PWM0 Channel D High Side
PWM0 Channel D Low Side
PWM0 PWMTMR Grouped
PWM0 Shutdown Input 0
PWM1 Channel A High Side
PWM1 Channel A Low Side
PWM1 Channel B High Side
PWM1 Channel B Low Side
PWM1 Channel C High Side
PWM1 Channel C Low Side
PWM1 Channel D High Side
PWM1 Channel D Low Side
PWM1 PWMTMR Grouped
PWM1 Shutdown Input 0
PWM2 Channel A High Side
PWM2 Channel A Low Side
PWM2 Channel B High Side
PWM2 Channel B Low Side
Rev. PrG |
Port
E
E
E
E
E
E
E
D
D
B
B
B
B
B
B
D
D
E
E
E
D
E
E
C
B
B
B
C
B
B
B
B
E
B
D
D
D
D
D
D
D
D
D
D
F
F
F
F
Page 48 of 168 |
June 2016
Pin Name
PE_09
PE_08
PE_07
PE_06
PE_05
PE_04
PE_00
PD_15
PD_14
PB_04
PB_05
PB_00
PB_01
PB_02
PB_03
PD_13
PD_12
PE_13
PE_14
PE_15
PD_00
PE_02
PE_01
PC_15
PB_07
PB_08
PB_06
PC_00
PB_13
PB_14
PB_11
PB_12
PE_09
PB_15
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PD_10
PD_11
PD_02
PF_07
PF_06
PF_09
PF_08
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
PWM2_CH
PWM2_CL
PWM2_DH
PWM2_DL
PWM2_SYNC
PWM2_TRIP0
GND
VDD_EXT
VDD_INT
RTC0_CLKIN
RTC0_XTAL
SINC0_CLK0
SINC0_D0
SINC0_D1
SINC0_D2
SINC0_D3
SMC0_A01
SMC0_A02
SMC0_A03
SMC0_A04
SMC0_A05
SMC0_A06
SMC0_A07
SMC0_A08
SMC0_A09
SMC0_A10
SMC0_A11
SMC0_A12
SMC0_A13
SMC0_A14
SMC0_A15
SMC0_A16
SMC0_A17
SMC0_A18
SMC0_A19
SMC0_A20
SMC0_A21
SMC0_A22
SMC0_A23
SMC0_A24
SMC0_A25
SMC0_ABE0
SMC0_ABE1
SMC0_AMS0
SMC0_AMS1
SMC0_AMS2
SMC0_AMS3
SMC0_AOE
Description
PWM2 Channel C High Side
PWM2 Channel C Low Side
PWM2 Channel D High Side
PWM2 Channel D Low Side
PWM2 PWMTMR Grouped
PWM2 Shutdown Input 0
Ground
External Voltage Domain
Internal Voltage Domain
RTC0 Crystal input / external oscillator connection
RTC0 Crystal output
SINC0 Clock 0
SINC0 Data 0
SINC0 Data 1
SINC0 Data 2
SINC0 Data 3
SMC0 Address 1
SMC0 Address 2
SMC0 Address 3
SMC0 Address 4
SMC0 Address 5
SMC0 Address 6
SMC0 Address 7
SMC0 Address 8
SMC0 Address 9
SMC0 Address 10
SMC0 Address 11
SMC0 Address 12
SMC0 Address 13
SMC0 Address 14
SMC0 Address 15
SMC0 Address 16
SMC0 Address 17
SMC0 Address 18
SMC0 Address 19
SMC0 Address 20
SMC0 Address 21
SMC0 Address 22
SMC0 Address 23
SMC0 Address 24
SMC0 Address 25
SMC0 Byte Enable 0
SMC0 Byte Enable 1
SMC0 Memory Select 0
SMC0 Memory Select 1
SMC0 Memory Select 2
SMC0 Memory Select 3
SMC0 Output Enable
Rev. PrG |
Page 49 of 168 |
June 2016
Port
D
E
E
E
E
D
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
B
A
A
B
B
B
B
B
B
D
D
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
C
E
E
C
E
C
C
D
Pin Name
PD_15
PE_00
PE_04
PE_10
PE_05
PD_14
GND
VDD_EXT
VDD_INT
RTC0_CLKIN
RTC0_XTAL
PB_01
PA_14
PA_15
PB_00
PB_04
PB_05
PB_06
PB_03
PB_02
PD_13
PD_12
PB_01
PB_00
PA_15
PA_14
PA_09
PA_08
PA_13
PA_12
PA_11
PA_07
PA_06
PA_05
PA_04
PA_01
PA_00
PA_10
PA_03
PA_02
PC_12
PE_14
PE_15
PC_15
PE_13
PC_07
PC_08
PD_01
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
SMC0_ARDY
SMC0_ARE
SMC0_AWE
SMC0_D00
SMC0_D01
SMC0_D02
SMC0_D03
SMC0_D04
SMC0_D05
SMC0_D06
SMC0_D07
SMC0_D08
SMC0_D09
SMC0_D10
SMC0_D11
SMC0_D12
SMC0_D13
SMC0_D14
SMC0_D15
SPI0_CLK
SPI0_MISO
SPI0_MOSI
SPI0_RDY
SPI0_SEL1
SPI0_SEL2
SPI0_SEL3
SPI0_SEL4
SPI0_SEL5
SPI0_SEL6
SPI0_SEL7
SPI0_SS
SPI1_CLK
SPI1_MISO
SPI1_MOSI
SPI1_RDY
SPI1_SEL1
SPI1_SEL2
SPI1_SEL3
SPI1_SEL4
SPI1_SEL5
SPI1_SEL6
SPI1_SEL7
SPI1_SS
SPI2_CLK
SPI2_D2
SPI2_D3
SPI2_MISO
SPI2_MOSI
Description
SMC0 Asynchronous Ready
SMC0 Read Enable
SMC0 Write Enable
SMC0 Data 0
SMC0 Data 1
SMC0 Data 2
SMC0 Data 3
SMC0 Data 4
SMC0 Data 5
SMC0 Data 6
SMC0 Data 7
SMC0 Data 8
SMC0 Data 9
SMC0 Data 10
SMC0 Data 11
SMC0 Data 12
SMC0 Data 13
SMC0 Data 14
SMC0 Data 15
SPI0 Clock
SPI0 Master In, Slave Out
SPI0 Master Out, Slave In
SPI0 Ready
SPI0 Slave Select Output 1
SPI0 Slave Select Output 2
SPI0 Slave Select Output 3
SPI0 Slave Select Output 4
SPI0 Slave Select Output 5
SPI0 Slave Select Output 6
SPI0 Slave Select Output 7
SPI0 Slave Select Input
SPI1 Clock
SPI1 Master In, Slave Out
SPI1 Master Out, Slave In
SPI1 Ready
SPI1 Slave Select Output 1
SPI1 Slave Select Output 2
SPI1 Slave Select Output 3
SPI1 Slave Select Output 4
SPI1 Slave Select Output 5
SPI1 Slave Select Output 6
SPI1 Slave Select Output 7
SPI1 Slave Select Input
SPI2 Clock
SPI2 Data 2
SPI2 Data 3
SPI2 Master In, Slave Out
SPI2 Master Out, Slave In
Rev. PrG |
Port
B
C
B
E
E
E
E
E
D
D
D
B
B
B
B
B
B
B
B
C
C
C
C
C
D
C
C
E
E
E
D
E
E
E
E
C
E
E
E
E
F
F
E
C
C
C
C
C
Page 50 of 168 |
June 2016
Pin Name
PB_04
PC_00
PB_15
PE_12
PE_11
PE_10
PE_09
PE_00
PD_15
PD_14
PD_00
PB_14
PB_13
PB_12
PB_11
PB_10
PB_09
PB_08
PB_07
PC_09
PC_10
PC_11
PC_12
PC_07
PD_01
PC_12
PC_00
PE_01
PE_02
PE_03
PD_01
PE_13
PE_14
PE_15
PE_08
PC_13
PE_07
PE_11
PE_12
PE_08
PF_00
PF_01
PE_11
PC_01
PC_04
PC_05
PC_02
PC_03
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
SPI2_RDY
SPI2_SEL1
SPI2_SEL2
SPI2_SEL3
SPI2_SEL4
SPI2_SEL5
SPI2_SS
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
SYS_FAULT
SYS_FAULT
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
TM0_ACI0
TM0_ACI1
TM0_ACI2
TM0_ACI3
TM0_ACI4
TM0_ACLK1
TM0_ACLK2
TM0_ACLK3
TM0_ACLK4
TM0_CLK
TM0_TMR0
TM0_TMR1
TM0_TMR2
TM0_TMR3
TM0_TMR4
TM0_TMR5
TM0_TMR6
TM0_TMR7
TRACE0_CLK
TRACE0_CLK
TRACE0_D00
TRACE0_D00
TRACE0_D01
TRACE0_D01
TRACE0_D02
TRACE0_D02
TRACE0_D03
TRACE0_D03
TRACE0_D04
Description
SPI2 Ready
SPI2 Slave Select Output 1
SPI2 Slave Select Output 2
SPI2 Slave Select Output 3
SPI2 Slave Select Output 4
SPI2 Slave Select Output 5
SPI2 Slave Select Input
Boot Mode Control 0
Boot Mode Control 1
Boot Mode Control 2
Clock/Crystal Input
Clock/Crystal Input
Processor Clock Output
Active-High Fault Output
Active-Low Fault Output
Processor Hardware Reset Control
Reset Output
Crystal Output
Crystal Output
TIMER0 Alternate Capture Input 0
TIMER0 Alternate Capture Input 1
TIMER0 Alternate Capture Input 2
TIMER0 Alternate Capture Input 3
TIMER0 Alternate Capture Input 4
TIMER0 Alternate Clock 1
TIMER0 Alternate Clock 2
TIMER0 Alternate Clock 3
TIMER0 Alternate Clock 4
TIMER0 Clock
TIMER0 Timer 0
TIMER0 Timer 1
TIMER0 Timer 2
TIMER0 Timer 3
TIMER0 Timer 4
TIMER0 Timer 5
TIMER0 Timer 6
TIMER0 Timer 7
TRACE0 Trace Clock
TRACE0 Trace Clock
TRACE0 Trace Data
TRACE0 Trace Data 0
TRACE0 Trace Data 1
TRACE0 Trace Data
TRACE0 Trace Data
TRACE0 Trace Data 2
TRACE0 Trace Data
TRACE0 Trace Data 3
TRACE0 Trace Data
Rev. PrG |
Page 51 of 168 |
Port
E
C
E
E
E
E
C
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
C
B
D
C
B
D
D
B
B
C
E
B
B
B
B
B
F
F
G
D
F
D
D
F
F
D
G
D
G
June 2016
Pin Name
PE_12
PC_06
PE_03
PE_04
PE_05
PE_06
PC_06
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
SYS_FAULT
SYS_FAULT
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
PC_14
PB_03
PD_13
PC_07
PB_10
PD_08
PD_09
PB_00
PB_01
PC_11
PE_09
PB_15
PB_10
PB_07
PB_08
PB_14
PF_00
PF_01
PG_00
PD_10
PF_13
PD_02
PD_03
PF_14
PF_15
PD_04
PG_01
PD_05
PG_02
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
TRACE0_D04
TRACE0_D05
TRACE0_D05
TRACE0_D06
TRACE0_D06
TRACE0_D07
TRACE0_D07
TRACE0_D08
TRACE0_D09
TRACE0_D10
TRACE0_D11
TRACE0_D12
TRACE0_D13
TRACE0_D14
TRACE0_D15
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
TWI2_SCL
TWI2_SDA
UART0_CTS
UART0_RTS
UART0_RX
UART0_TX
UART1_CTS
UART1_RTS
UART1_RX
UART1_TX
UART2_CTS
UART2_RTS
UART2_RX
UART2_TX
USB0_CLKIN
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
USB0_XTAL
USB1_DM
USB1_DP
USB1_VBUS
VDD_DMC
VDD_HADC
VDD_PCIE
VDD_PCIE_RX
Description
TRACE0 Trace Data 4
TRACE0 Trace Data 5
TRACE0 Trace Data
TRACE0 Trace Data
TRACE0 Trace Data 6
TRACE0 Trace Data
TRACE0 Trace Data 7
TRACE0 Trace Data 8
TRACE0 Trace Data 9
TRACE0 Trace Data 10
TRACE0 Trace Data 11
TRACE0 Trace Data 12
TRACE0 Trace Data 13
TRACE0 Trace Data 14
TRACE0 Trace Data 15
TWI0 Serial Clock
TWI0 Serial Data
TWI1 Serial Clock
TWI1 Serial Data
TWI2 Serial Clock
TWI2 Serial Data
UART0 Clear to Send
UART0 Request to Send
UART0 Receive
UART0 Transmit
UART1 Clear to Send
UART1 Request to Send
UART1 Receive
UART1 Transmit
UART2 Clear to Send
UART2 Request to Send
UART2 Receive
UART2 Transmit
USB0 Clock/Crystal Input
USB0 Data –
USB0 Data +
USB0 OTG ID
USB0 VBUS Control
USB0 Bus Voltage
USB0 Crystal
USB1 Data USB1 Data +
USB1 Bus Voltage
DMC VDD
HADC VDD
PCIE Supply Voltage
PCIE RX Supply Voltage
Rev. PrG |
Port
D
D
G
G
D
G
D
F
F
F
G
G
G
G
G
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
D
C
C
C
E
E
B
B
E
E
D
D
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Not Muxed
Page 52 of 168 |
June 2016
Pin Name
PD_06
PD_07
PG_03
PG_04
PD_08
PG_05
PD_09
PF_13
PF_14
PF_15
PG_01
PG_02
PG_03
PG_04
PG_05
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
TWI2_SCL
TWI2_SDA
PD_00
PC_15
PC_14
PC_13
PE_01
PE_02
PB_03
PB_02
PE_11
PE_10
PD_13
PD_12
USB_CLKIN
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
USB_XTAL
USB1_DM
USB1_DP
USB1_VBUS
VDD_DMC
VDD_HADC
VDD_PCIE
VDD_PCIE_RX
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 19. ADSP-SC58x/ADSP-2158x 529-Ball CSP_BGA Signal Descriptions (Continued)
Signal Name
VDD_PCIE_TX
VDD_RTC
VDD_USB
Description
PCIE TX Supply Voltage
RTC VDD
USB VDD
Rev. PrG |
Port
Not Muxed
Not Muxed
Not Muxed
Page 53 of 168 |
June 2016
Pin Name
VDD_PCIE_TX
VDD_RTC
VDD_USB
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
GPIO MULTIPLEXING FOR 529-BALL CSP_BGA
Table 20 through Table 26 identify the pin functions that are
multiplexed on the general-purpose I/O pins of the 529-ball
CSP_BGA package.
Table 20. Signal Multiplexing for Port A
Signal Name
PA_00
PA_01
PA_02
PA_03
PA_04
PA_05
PA_06
PA_07
PA_08
PA_09
PA_10
PA_11
PA_12
PA_13
PA_14
PA_15
Multiplexed
Function 0
ETH0_TXD0
ETH0_TXD1
ETH0_MDC
ETH0_MDIO
ETH0_RXD0
ETH0_RXD1
ETH0_RXCLK_REFCLK
ETH0_CRS
ETH0_RXD2
ETH0_RXD3
ETH0_TXEN
ETH0_TXCLK
ETH0_TXD2
ETH0_TXD3
ETH0_PTPPPS3
ETH0_PTPPPS2
Multiplexed
Function 1
SINC0_D0
SINC0_D1
Multiplexed Function Multiplexed
2
Function 3
SMC0_A21
SMC0_A20
SMC0_A24
SMC0_A23
SMC0_A19
SMC0_A18
SMC0_A17
SMC0_A16
SMC0_A12
SMC0_A11
SMC0_A22
SMC0_A15
SMC0_A14
SMC0_A13
SMC0_A10
SMC0_A09
Multiplexed
Function Input Tap
Multiplexed
Function 2
PPI0_D14
PPI0_D15
PPI0_D16
PPI0_D17
PPI0_D12
PPI0_D13
PWM0_BH
TM0_TMR3
TM0_TMR4
CAN1_TX
CAN1_RX
PWM0_DH
PWM0_DL
PWM0_CH
PWM0_CL
TM0_TMR1
Multiplexed
Function Input Tap
TM0_ACLK3
TM0_ACLK4
Table 21. Signal Multiplexing for Port B
Signal Name
PB_00
PB_01
PB_02
PB_03
PB_04
PB_05
PB_06
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
PB_15
Multiplexed
Function 0
ETH0_PTPPPS1
ETH0_PTPPPS0
ETH0_PTPCLKIN0
ETH0_PTPAUXIN0
MLB0_CLK
MLB0_SIG
MLB0_DAT
LP1_D0
LP1_D1
LP1_D2
LP1_D3
LP1_D4
LP1_D5
LP1_D6
LP1_D7
LP1_ACK
Multiplexed
Function 1
SINC0_D2
SINC0_CLK0
UART1_TX
UART1_RX
SINC0_D3
PWM0_AH
PWM0_AL
TM0_TMR2
TM0_TMR5
PWM0_TRIP0
Rev. PrG |
Page 54 of 168 |
June 2016
Multiplexed
Function 3
SMC0_A08
SMC0_A07
SMC0_A04
SMC0_A03
SMC0_ARDY
SMC0_A01
SMC0_A02
SMC0_D15
SMC0_D14
SMC0_D13
SMC0_D12
SMC0_D11
SMC0_D10
SMC0_D09
SMC0_D08
SMC0_AWE
TM0_ACI1
ETH0_PTPAUXIN1
ETH0_PTPAUXIN2
ETH0_PTPAUXIN3
TM0_ACI4
CNT0_ZM
CNT0_UD
CNT0_DG
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 22. Signal Multiplexing for Port C
Signal Name
PC_00
PC_01
PC_02
PC_03
PC_04
PC_05
PC_06
PC_07
PC_08
PC_09
PC_10
PC_11
PC_12
PC_13
PC_14
PC_15
Multiplexed
Function 0
LP1_CLK
SPI2_CLK
SPI2_MISO
SPI2_MOSI
SPI2_D2
SPI2_D3
SPI2_SEL1
CAN0_RX
CAN0_TX
SPI0_CLK
SPI0_MISO
SPI0_MOSI
SPI0_SEL3
UART0_TX
UART0_RX
UART0_RTS
Multiplexed
Function 1
PWM0_BL
Multiplexed
Function 2
SPI0_SEL4
SPI0_SEL1
Multiplexed
Function 3
SMC0_ARE
SMC0_AMS2
SMC0_AMS3
Multiplexed
Function Input Tap
SPI2_SS
TM0_ACI3
TM0_CLK
SPI0_RDY
SPI1_SEL1
PPI0_FS3
ACM0_T0
ACM0_A0
ACM0_A1
ACM0_A2
SMC0_A25
Multiplexed
Function 2
ACM0_A3
ACM0_A4
TRACE0_D00
TRACE0_D01
TRACE0_D02
TRACE0_D03
TRACE0_D04
TRACE0_D05
TRACE0_D06
TRACE0_D07
TRACE0_CLK
Multiplexed
Function 3
SMC0_D07
SMC0_AOE
PPI0_D19
PPI0_D18
MLB0_CLKOUT
SMC0_A06
SMC0_A05
SMC0_D06
SMC0_D05
TM0_ACI0
SMC0_AMS0
Table 23. Signal Multiplexing for Port D
Signal Name
PD_00
PD_01
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PD_10
PD_11
PD_12
PD_13
PD_14
PD_15
Multiplexed
Function 0
UART0_CTS
SPI0_SEL2
LP0_D0
LP0_D1
LP0_D2
LP0_D3
LP0_D4
LP0_D5
LP0_D6
LP0_D7
LP0_CLK
LP0_ACK
UART2_TX
UART2_RX
PPI0_D11
PPI0_D10
Multiplexed
Function 1
PPI0_D23
PWM1_TRIP0
PWM1_AH
PWM1_AL
PWM1_BH
PWM1_BL
PWM1_CH
PWM1_CL
PWM1_DH
PWM1_DL
PWM1_SYNC
PWM2_TRIP0
PWM2_CH
Rev. PrG |
Page 55 of 168 |
June 2016
Multiplexed
Function Input Tap
SPI0_SS
TM0_ACLK1
TM0_ACLK2
TM0_ACI2
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 24. Signal Multiplexing for Port E
Signal Name
PE_00
PE_01
PE_02
PE_03
PE_04
PE_05
PE_06
PE_07
PE_08
PE_09
PE_10
PE_11
PE_12
PE_13
PE_14
PE_15
Multiplexed
Function 0
PPI0_D09
PPI0_FS2
PPI0_FS1
PPI0_CLK
PPI0_D08
PPI0_D07
PPI0_D06
PPI0_D05
PPI0_D04
PPI0_D03
PPI0_D02
PPI0_D01
PPI0_D00
SPI1_CLK
SPI1_MISO
SPI1_MOSI
Multiplexed
Function 1
PWM2_CL
SPI0_SEL5
SPI0_SEL6
SPI0_SEL7
PWM2_DH
PWM2_SYNC
Multiplexed
Function 2
Multiplexed
Function Input Tap
UART1_CTS
UART1_RTS
SPI2_SEL2
SPI2_SEL3
SPI2_SEL4
SPI2_SEL5
SPI1_SEL2
SPI1_RDY
TM0_TMR0
UART2_RTS
UART2_CTS
SPI2_RDY
PPI0_D20
PPI0_D21
PPI0_D22
Multiplexed
Function 3
SMC0_D04
C1_FLG0
C2_FLG0
C1_FLG1
C2_FLG1
C1_FLG2
C2_FLG2
C1_FLG3
C2_FLG3
SMC0_D03
SMC0_D02
SMC0_D01
SMC0_D00
SMC0_AMS1
SMC0_ABE0
SMC0_ABE1
Multiplexed
Function 1
SPI1_SEL6
SPI1_SEL7
HADC0_EOC_DOUT
HADC0_MUX2
HADC0_MUX1
HADC0_MUX0
PWM2_AL
PWM2_AH
PWM2_BL
PWM2_BH
Multiplexed
Function 2
Multiplexed
Function 3
Multiplexed
Function Input Tap
TRACE0_D08
TRACE0_D09
TRACE0_D10
TRACE0_D00
TRACE0_D01
TRACE0_D02
MSI0_INT
SPI1_SEL5
PWM0_SYNC
PWM2_DL
SPI1_SEL3
SPI1_SEL4
SPI1_SS
Table 25. Signal Multiplexing for Port F
Signal Name
PF_00
PF_01
PF_02
PF_03
PF_04
PF_05
PF_06
PF_07
PF_08
PF_09
PF_10
PF_11
PF_12
PF_13
PF_14
PF_15
Multiplexed
Function 0
TM0_TMR6
TM0_TMR7
MSI0_D0
MSI0_D1
MSI0_D2
MSI0_D3
MSI0_D4
MSI0_D5
MSI0_D6
MSI0_D7
MSI0_CMD
MSI0_CLK
MSI0_CD
ETH1_CRS
ETH1_MDC
ETH1_MDIO
Rev. PrG |
Page 56 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 26. Signal Multiplexing for Port G
Signal Name
PG_00
PG_01
PG_02
PG_03
PG_04
PG_05
Multiplexed
Function 0
ETH1_REFCLK
ETH1_TXEN
ETH1_TXD0
ETH1_TXD1
ETH1_RXD0
ETH1_RXD1
Multiplexed
Function 1
TRACE0_CLK
TRACE0_D11
TRACE0_D12
TRACE0_D13
TRACE0_D14
TRACE0_D15
Rev. PrG |
Multiplexed
Function 2
TRACE0_D03
TRACE0_D04
TRACE0_D05
TRACE0_D06
TRACE0_D07
Page 57 of 168 |
June 2016
Multiplexed
Function 3
Multiplexed
Function Input Tap
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
ADSP-SC58X/ADSP-2158X DESIGNER QUICK REFERENCE
Table 27 provides a quick reference summary of pin related
information for circuit board design. The columns in this table
provide the following information:
• Reset Termination: The Reset Term column in the table
specifies the termination present when the processor is in
the reset state.
• Signal Name: The Signal Name column in the table
includes the signal name for every pin and (where applicable) the GPIO multiplexed pin function for every pin.
• Reset Drive: The Reset Drive column in the table specifies
the active drive on the signal when the processor is in the
reset state.
• Pin Type: The Type column in the table identifies the I/O
type or supply type of the pin. The abbreviations used in
this column are a (analog), s (supply), g (ground) and
Input/Output/InOut.
• Power Domain: The Power Domain column in the table
specifies the power supply domain in which the signal
resides.
• Driver Type: The Driver Type column in the table identifies the driver type used by the pin. The driver types are
defined in the output drive currents section of this data
sheet.
• Internal Termination: The Int Term column in the table
specifies the termination present when the processor is not
in the reset state.
• Description and Notes: The Description and Notes column
in the table identifies any special requirements or characteristics for the signal. If no special requirements are listed
the signal may be left unconnected if it is not used. Also, for
multiplexed general-purpose I/O pins, this column identifies the functions available on the pin.
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference
Signal Name
DAI0_PIN01
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
DAI0_PIN02
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN03
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN04
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN05
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN06
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN07
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN08
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN09
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN10
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN11
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN12
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN13
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN14
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 58 of 168 |
June 2016
Description
and Notes
Desc: DAI0 Pin 1
Notes: No notes
Desc: DAI0 Pin 2
Notes: No notes
Desc: DAI0 Pin 3
Notes: No notes
Desc: DAI0 Pin 4
Notes: No notes
Desc: DAI0 Pin 5
Notes: No notes
Desc: DAI0 Pin 6
Notes: No notes
Desc: DAI0 Pin 7
Notes: No notes
Desc: DAI0 Pin 8
Notes: No notes
Desc: DAI0 Pin 9
Notes: No notes
Desc: DAI0 Pin 10
Notes: No notes
Desc: DAI0 Pin 11
Notes: No notes
Desc: DAI0 Pin 12
Notes: No notes
Desc: DAI0 Pin 13
Notes: No notes
Desc: DAI0 Pin 14
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
DAI0_PIN15
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
DAI0_PIN16
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN17
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN18
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN19
InOut
A
PullDown
none
none
VDD_EXT
DAI0_PIN20
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN01
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN02
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN03
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN04
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN05
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN06
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN07
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN08
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN09
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN10
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN11
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN12
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN13
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN14
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN15
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN16
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN17
InOut
A
PullDown
none
none
VDD_EXT
DAI1_PIN18
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 59 of 168 |
June 2016
Description
and Notes
Desc: DAI0 Pin 15
Notes: No notes
Desc: DAI0 Pin 16
Notes: No notes
Desc: DAI0 Pin 17
Notes: No notes
Desc: DAI0 Pin 18
Notes: No notes
Desc: DAI0 Pin 19
Notes: No notes
Desc: DAI0 Pin 20
Notes: No notes
Desc: DAI1 Pin 1
Notes: No notes
Desc: DAI1 Pin 2
Notes: No notes
Desc: DAI1 Pin 3
Notes: No notes
Desc: DAI1 Pin 4
Notes: No notes
Desc: DAI1 Pin 5
Notes: No notes
Desc: DAI1 Pin 6
Notes: No notes
Desc: DAI1 Pin 7
Notes: No notes
Desc: DAI1 Pin 8
Notes: No notes
Desc: DAI1 Pin 9
Notes: No notes
Desc: DAI1 Pin 10
Notes: No notes
Desc: DAI1 Pin 11
Notes: No notes
Desc: DAI1 Pin 12
Notes: No notes
Desc: DAI1 Pin 13
Notes: No notes
Desc: DAI1 Pin 14
Notes: No notes
Desc: DAI1 Pin 15
Notes: No notes
Desc: DAI1 Pin 16
Notes: No notes
Desc: DAI1 Pin 17
Notes: No notes
Desc: DAI1 Pin 18
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
DAI1_PIN19
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
DAI1_PIN20
InOut
A
PullDown
none
none
VDD_EXT
DMC0_A00
Output
B
none
none
none
VDD_DMC
DMC0_A01
Output
B
none
none
none
VDD_DMC
DMC0_A02
Output
B
none
none
none
VDD_DMC
DMC0_A03
Output
B
none
none
none
VDD_DMC
DMC0_A04
Output
B
none
none
none
VDD_DMC
DMC0_A05
Output
B
none
none
none
VDD_DMC
DMC0_A06
Output
B
none
none
none
VDD_DMC
DMC0_A07
Output
B
none
none
none
VDD_DMC
DMC0_A08
Output
B
none
none
none
VDD_DMC
DMC0_A09
Output
B
none
none
none
VDD_DMC
DMC0_A10
Output
B
none
none
none
VDD_DMC
DMC0_A11
Output
B
none
none
none
VDD_DMC
DMC0_A12
Output
B
none
none
none
VDD_DMC
DMC0_A13
Output
B
none
none
none
VDD_DMC
DMC0_A14
Output
B
none
none
none
VDD_DMC
DMC0_A15
Output
B
none
none
none
VDD_DMC
DMC0_BA0
Output
B
none
none
none
VDD_DMC
DMC0_BA1
Output
B
none
none
none
VDD_DMC
DMC0_BA2
Output
B
none
none
none
VDD_DMC
DMC0_CAS
Output
B
none
none
none
VDD_DMC
Rev. PrG |
Page 60 of 168 |
June 2016
Description
and Notes
Desc: DAI1 Pin 19
Notes: No notes
Desc: DAI1 Pin 20
Notes: No notes
Desc: DMC0 Address 0
Notes: No notes
Desc: DMC0 Address 1
Notes: No notes
Desc: DMC0 Address 2
Notes: No notes
Desc: DMC0 Address 3
Notes: No notes
Desc: DMC0 Address 4
Notes: No notes
Desc: DMC0 Address 5
Notes: No notes
Desc: DMC0 Address 6
Notes: No notes
Desc: DMC0 Address 7
Notes: No notes
Desc: DMC0 Address 8
Notes: No notes
Desc: DMC0 Address 9
Notes: No notes
Desc: DMC0 Address 10
Notes: No notes
Desc: DMC0 Address 11
Notes: No notes
Desc: DMC0 Address 12
Notes: No notes
Desc: DMC0 Address 13
Notes: No notes
Desc: DMC0 Address 14
Notes: No notes
Desc: DMC0 Address 15
Notes: No notes
Desc: DMC0 Bank Address Input
0
Notes: No notes
Desc: DMC0 Bank Address Input
1
Notes: No notes
Desc: DMC0 Bank Address Input
2
Notes: No notes
Desc: DMC0 Column Address
Strobe
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
DMC0_CK
Type
Output
Driver
Type
C
Int
Term
Reset
Term
Reset
Drive
none
none
L
Power Domain
VDD_DMC
DMC0_CKE
Output
B
none
none
L
VDD_DMC
DMC0_CK
Output
C
none
none
L
VDD_DMC
DMC0_CS0
Output
B
none
none
none
VDD_DMC
DMC0_DQ00
InOut
B
none
none
VDD_DMC
DMC0_DQ01
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 1
Notes: No notes
DMC0_DQ02
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 2
Notes: No notes
DMC0_DQ03
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 3
Notes: No notes
DMC0_DQ04
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 4
Notes: No notes
DMC0_DQ05
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 5
Notes: No notes
DMC0_DQ06
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 6
Notes: No notes
DMC0_DQ07
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 7
Notes: No notes
DMC0_DQ08
InOut
B
none
none
VDD_DMC
Desc: DMC0 Data 8
Notes: No notes
DMC0_DQ09
InOut
B
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
none
none
VDD_DMC
Desc: DMC0 Data 9
Notes: No notes
Rev. PrG |
Page 61 of 168 |
June 2016
Description
and Notes
Desc: DMC0 Clock
Notes: No notes
Desc: DMC0 Clock enable
Notes: No notes
Desc: DMC0 Clock (complement)
Notes: No notes
Desc: DMC0 Chip Select 0
Notes: No notes
Desc: DMC0 Data 0
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Int
Term
Reset
Term
Reset
Drive
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
none
none
none
Power Domain
VDD_DMC
none
none
VDD_DMC
Desc: DMC0 Data 11
Notes: No notes
none
none
VDD_DMC
Desc: DMC0 Data 12
Notes: No notes
none
none
VDD_DMC
Desc: DMC0 Data 13
Notes: No notes
none
none
VDD_DMC
Desc: DMC0 Data 14
Notes: No notes
none
none
VDD_DMC
Desc: DMC0 Data 15
Notes: No notes
none
none
VDD_DMC
Internal logic
none
ensures that
input signal does
not float
Internal logic
none
ensures that
input signal does
not float
none
VDD_DMC
Desc: DMC0 Data Mask for Lower
Byte
Notes: No notes
Desc: DMC0 Data Strobe for
Lower Byte (complement)
Notes: No notes
none
VDD_DMC
B
none
none
none
VDD_DMC
Output
B
none
none
none
VDD_DMC
DMC0_RESET
Output
B
none
none
none
VDD_DMC
DMC0_RZQ
a
B
none
none
none
VDD_DMC
DMC0_UDM
Output
B
none
none
none
VDD_DMC
Signal Name
DMC0_DQ10
Type
InOut
Driver
Type
B
DMC0_DQ11
InOut
B
DMC0_DQ12
InOut
B
DMC0_DQ13
InOut
B
DMC0_DQ14
InOut
B
DMC0_DQ15
InOut
B
DMC0_LDM
Output
B
DMC0_LDQS
InOut
C
DMC0_LDQS
InOut
C
DMC0_ODT
Output
DMC0_RAS
Rev. PrG |
Page 62 of 168 |
June 2016
Description
and Notes
Desc: DMC0 Data 10
Notes: No notes
Desc: DMC0 Data Strobe for
Lower Byte
Notes: External weak pull-down
required in LPDDR mode
Desc: DMC0 On-die termination
Notes: No notes
Desc: DMC0 Row Address Strobe
Notes: No notes
Desc: DMC0 Reset (DDR3 only)
Notes: No notes
Desc: DMC0 External calibration
resistor connection
Notes: Applicable for DDR2 and
DDR3 only. External pull-down
of 34 ohms need to be added.
Desc: DMC0 Data Mask for Upper
Byte
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Reset
Term
Reset
Drive
Internal logic
none
ensures that
input signal does
not float
none
Power Domain
VDD_DMC
Internal logic
none
ensures that
input signal does
not float
none
none
none
VDD_DMC
none
VDD_DMC
B
none
none
none
VDD_DMC
Output
B
none
none
none
VDD_DMC
DMC1_A01
Output
B
none
none
none
VDD_DMC
DMC1_A02
Output
B
none
none
none
VDD_DMC
DMC1_A03
Output
B
none
none
none
VDD_DMC
DMC1_A04
Output
B
none
none
none
VDD_DMC
DMC1_A05
Output
B
none
none
none
VDD_DMC
DMC1_A06
Output
B
none
none
none
VDD_DMC
DMC1_A07
Output
B
none
none
none
VDD_DMC
DMC1_A08
Output
B
none
none
none
VDD_DMC
DMC1_A09
Output
B
none
none
none
VDD_DMC
DMC1_A10
Output
B
none
none
none
VDD_DMC
DMC1_A11
Output
B
none
none
none
VDD_DMC
DMC1_A12
Output
B
none
none
none
VDD_DMC
DMC1_A13
Output
B
none
none
none
VDD_DMC
DMC1_A14
Output
B
none
none
none
VDD_DMC
DMC1_A15
Output
B
none
none
none
VDD_DMC
DMC1_BA0
Output
B
none
none
none
VDD_DMC
Signal Name
DMC0_UDQS
Type
InOut
Driver
Type
C
DMC0_UDQS
InOut
C
DMC0_VREF
a
DMC0_WE
Output
DMC1_A00
Int
Term
Rev. PrG |
Page 63 of 168 |
June 2016
Description
and Notes
Desc: DMC0 Data Strobe for
Upper Byte
Notes: External weak pull-down
required in LPDDR mode
Desc: DMC0 Data Strobe for
Upper Byte (complement)
Notes: No notes
Desc: DMC0 Voltage Reference
Notes: No notes
Desc: DMC0 Write Enable
Notes: No notes
Desc: DMC1 Address 0
Notes: No notes
Desc: DMC1 Address 1
Notes: No notes
Desc: DMC1 Address 2
Notes: No notes
Desc: DMC1 Address 3
Notes: No notes
Desc: DMC1 Address 4
Notes: No notes
Desc: DMC1 Address 5
Notes: No notes
Desc: DMC1 Address 6
Notes: No notes
Desc: DMC1 Address 7
Notes: No notes
Desc: DMC1 Address 8
Notes: No notes
Desc: DMC1 Address 9
Notes: No notes
Desc: DMC1 Address 10
Notes: No notes
Desc: DMC1 Address 11
Notes: No notes
Desc: DMC1 Address 12
Notes: No notes
Desc: DMC1 Address 13
Notes: No notes
Desc: DMC1 Address 14
Notes: No notes
Desc: DMC1 Address 15
Notes: No notes
Desc: DMC1 Bank Address Input
0
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
DMC1_BA1
Type
Output
Driver
Type
B
Int
Term
Reset
Term
Reset
Drive
none
none
none
Power Domain
VDD_DMC
DMC1_BA2
Output
B
none
none
none
VDD_DMC
DMC1_CAS
Output
B
none
none
none
VDD_DMC
DMC1_CK
Output
C
none
none
L
VDD_DMC
DMC1_CKE
Output
B
none
none
L
VDD_DMC
DMC1_CK
Output
C
none
none
L
VDD_DMC
DMC1_CS0
Output
B
none
none
none
VDD_DMC
DMC1_DQ00
InOut
B
none
none
VDD_DMC
DMC1_DQ01
InOut
B
none
none
VDD_DMC
Desc: DMC1 Data 1
Notes: No notes
DMC1_DQ02
InOut
B
none
none
VDD_DMC
Desc: DMC1 Data 2
Notes: No notes
DMC1_DQ03
InOut
B
none
none
VDD_DMC
Desc: DMC1 Data 3
Notes: No notes
DMC1_DQ04
InOut
B
none
none
VDD_DMC
Desc: DMC1 Data 4
Notes: No notes
DMC1_DQ05
InOut
B
none
none
VDD_DMC
Desc: DMC1 Data 5
Notes: No notes
DMC1_DQ06
InOut
B
none
none
VDD_DMC
Desc: DMC1 Data 6
Notes: No notes
DMC1_DQ07
InOut
B
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
none
none
VDD_DMC
Desc: DMC1 Data 7
Notes: No notes
Rev. PrG |
Page 64 of 168 |
June 2016
Description
and Notes
Desc: DMC1 Bank Address Input
1
Notes: No notes
Desc: DMC1 Bank Address Input
2
Notes: No notes
Desc: DMC1 Column Address
Strobe
Notes: No notes
Desc: DMC1 Clock
Notes: No notes
Desc: DMC1 Clock enable
Notes: No notes
Desc: DMC1 Clock (complement)
Notes: No notes
Desc: DMC1 Chip Select 0
Notes: No notes
Desc: DMC1 Data 0
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Int
Term
Reset
Term
Reset
Drive
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
none
none
none
Power Domain
VDD_DMC
none
none
VDD_DMC
Desc: DMC1 Data 9
Notes: No notes
none
none
VDD_DMC
Desc: DMC1 Data 10
Notes: No notes
none
none
VDD_DMC
Desc: DMC1 Data 11
Notes: No notes
none
none
VDD_DMC
Desc: DMC1 Data 12
Notes: No notes
none
none
VDD_DMC
Desc: DMC1 Data 13
Notes: No notes
none
none
VDD_DMC
Desc: DMC1 Data 14
Notes: No notes
none
none
VDD_DMC
Desc: DMC1 Data 15
Notes: No notes
none
none
VDD_DMC
C
Internal logic
none
ensures that
input signal does
not float
none
VDD_DMC
InOut
C
none
VDD_DMC
DMC1_ODT
Output
B
Internal logic
none
ensures that
input signal does
not float
none
none
Desc: DMC1 Data Mask for Lower
Byte
Notes: No notes
Desc: DMC1 Data Strobe for
Lower Byte
Notes: External weak pull-down
required in LPDDR mode
Desc: DMC1 Data Strobe for
Lower Byte (complement)
Notes: No notes
none
VDD_DMC
DMC1_RAS
Output
B
none
none
none
VDD_DMC
DMC1_RESET
InOut
B
none
none
none
VDD_DMC
Signal Name
DMC1_DQ08
Type
InOut
Driver
Type
B
DMC1_DQ09
InOut
B
DMC1_DQ10
InOut
B
DMC1_DQ11
InOut
B
DMC1_DQ12
InOut
B
DMC1_DQ13
InOut
B
DMC1_DQ14
InOut
B
DMC1_DQ15
InOut
B
DMC1_LDM
Output
B
DMC1_LDQS
InOut
DMC1_LDQS
Rev. PrG |
Page 65 of 168 |
June 2016
Description
and Notes
Desc: DMC1 Data 8
Notes: No notes
Desc: DMC1 On-die termination
Notes: No notes
Desc: DMC1 Row Address Strobe
Notes: No notes
Desc: DMC1 Reset (DDR3 only)
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
DMC1_RZQ
Type
a
Driver
Type
B
Int
Term
Reset
Term
Reset
Drive
none
none
none
Power Domain
VDD_DMC
DMC1_UDM
Output
B
none
none
none
VDD_DMC
DMC1_UDQS
InOut
C
Internal logic
none
ensures that
input signal does
not float
none
VDD_DMC
DMC1_UDQS
InOut
C
none
VDD_DMC
DMC1_VREF
a
Internal logic
none
ensures that
input signal does
not float
none
none
none
VDD_DMC
DMC1_WE
Output
B
none
none
none
GND
g
NA
none
none
none
HADC0_VIN0
a
NA
none
none
none
VDD_HADC
HADC0_VIN1
a
NA
none
none
none
VDD_HADC
HADC0_VIN2
a
NA
none
none
none
VDD_HADC
HADC0_VIN3
a
NA
none
none
none
VDD_HADC
HADC0_VIN4
a
NA
none
none
none
VDD_HADC
HADC0_VIN5
a
NA
none
none
none
VDD_HADC
HADC0_VIN6
a
NA
none
none
none
VDD_HADC
Rev. PrG |
Page 66 of 168 |
June 2016
Description
and Notes
Desc: DMC1 External calibration
resistor connection
Notes: Applicable for DDR2 and
DDR3 only. External pull-down
of 34 ohms need to be added.
Desc: DMC1 Data Mask for Upper
Byte
Notes: No notes
Desc: DMC1 Data Strobe for
Upper Byte
Notes: External weak pull-down
required in LPDDR mode
Desc: DMC1 Data Strobe for
Upper Byte (complement)
Notes: No notes
Desc: DMC1 Voltage Reference
Notes: No notes
Desc: DMC1 Write Enable
Notes: No notes
Desc: Ground
Notes: No notes
Desc: HADC0 Analog Input at
channel 0
Notes: If Input not used connect
to GND
Desc: HADC0 Analog Input at
channel 1
Notes: If Input not used connect
to GND
Desc: HADC0 Analog Input at
channel 2
Notes: If Input not used connect
to GND
Desc: HADC0 Analog Input at
channel 3
Notes: If Input not used connect
to GND
Desc: HADC0 Analog Input at
channel 4
Notes: If Input not used connect
to GND
Desc: HADC0 Analog Input at
channel 5
Notes: If Input not used connect
to GND
Desc: HADC0 Analog Input at
channel 6
Notes: If Input not used connect
to GND
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
HADC0_VIN7
Type
a
Driver
Type
NA
Int
Term
Reset
Term
Reset
Drive
none
none
none
Power Domain
VDD_HADC
HADC0_VREFN
s
NA
none
none
none
VDD_HADC
HADC0_VREFP
s
NA
none
none
none
VDD_HADC
JTG_TCK
Input
PullUp
none
none
VDD_EXT
JTG_TDI
Input
PullUp
none
none
VDD_EXT
JTG_TDO
Output
A
none
none
none
VDD_EXT
JTG_TMS
InOut
A
PullUp
none
none
VDD_EXT
JTG_TRST
Input
PullDown
none
none
VDD_EXT
MLB0_CLKN
Input
TBD
none
none
VDD_EXT
MLB0_CLKP
Input
TBD
none
none
VDD_EXT
Desc: MLB0 Differential Clock (+)
Notes: No notes
MLB0_DATN
InOut
TBD
none
none
VDD_EXT
Desc: MLB0 Differential Data (-)
Notes: No notes
MLB0_DATP
InOut
TBD
none
none
VDD_EXT
Desc: MLB0 Differential Data (+)
Notes: No notes
MLB0_SIGN
InOut
TBD
none
none
VDD_EXT
Desc: MLB0 Differential Signal (-)
Notes: No notes
MLB0_SIGP
InOut
TBD
none
none
VDD_EXT
Desc: MLB0 Differential Signal
(+)
Notes: No notes
PA_00
InOut
A
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
Internal logic
ensures that
input signal does
not float
PullDown
none
none
VDD_EXT
Desc: PORTA Position 0 | EMAC0
Transmit Data 0 | SMC0 Address
21
Notes: No notes
Rev. PrG |
Page 67 of 168 |
June 2016
Description
and Notes
Desc: HADC0 Analog Input at
channel 7
Notes: If Input not used connect
to GND
Desc: HADC0 Ground Reference
for ADC
Notes: No notes
Desc: HADC0 External Reference
for ADC
Notes: No notes
Desc: JTAG Clock
Notes: No notes
Desc: JTAG Serial Data In
Notes: No notes
Desc: JTAG Serial Data Out
Notes: No notes
Desc: JTAG Mode Select
Notes: No notes
Desc: JTAG Reset
Notes: No notes
Desc: MLB0 Differential Clock (-)
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PA_01
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PA_02
InOut
A
PullDown
none
none
VDD_EXT
PA_03
InOut
A
PullDown
none
none
VDD_EXT
PA_04
InOut
A
PullDown
none
none
VDD_EXT
PA_05
InOut
A
PullDown
none
none
VDD_EXT
PA_06
InOut
A
PullDown
none
none
VDD_EXT
PA_07
InOut
A
PullDown
none
none
VDD_EXT
PA_08
InOut
A
PullDown
none
none
VDD_EXT
PA_09
InOut
A
PullDown
none
none
VDD_EXT
PA_10
InOut
A
PullDown
none
none
VDD_EXT
PA_11
InOut
A
PullDown
none
none
VDD_EXT
PA_12
InOut
A
PullDown
none
none
VDD_EXT
PA_13
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 68 of 168 |
June 2016
Description
and Notes
Desc: PORTA Position 1 | EMAC0
Transmit Data 1 | SMC0 Address
20
Notes: No notes
Desc: PORTA Position 2 | EMAC0
Management Channel Clock |
SMC0 Address 24
Notes: No notes
Desc: PORTA Position 3 | EMAC0
Management Channel Serial
Data | SMC0 Address 23
Notes: No notes
Desc: PORTA Position 4 | EMAC0
Receive Data 0 | SMC0 Address 19
Notes: No notes
Desc: PORTA Position 5 | EMAC0
Receive Data 1 | SMC0 Address 18
Notes: No notes
Desc: PORTA Position 6 | EMAC0
RXCLK (GigE) or REFCLK (10/100)
| SMC0 Address 17
Notes: No notes
Desc: EMAC0 RXCTL (GigE) or
CRS (10/100) | PORTA Position 7 |
EMAC0 Carrier Sense/RMII
Receive Data Valid | SMC0
Address 16
Notes: No notes
Desc: PORTA Position 8 | EMAC0
Receive Data 2 | SMC0 Address 12
Notes: No notes
Desc: PORTA Position 9 | EMAC0
Receive Data 3 | SMC0 Address 11
Notes: No notes
Desc: EMAC0 TXCTL (GigE) or
TXEN (10/100) | PORTA Position
10 | EMAC0 Transmit Enable |
SMC0 Address 22
Notes: No notes
Desc: PORTA Position 11 | EMAC0
Transmit Clock | SMC0 Address
15
Notes: No notes
Desc: PORTA Position 12 | EMAC0
Transmit Data 2 | SMC0 Address
14
Notes: No notes
Desc: PORTA Position 13 | EMAC0
Transmit Data 3 | SMC0 Address
13
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PA_14
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PA_15
InOut
A
PullDown
none
none
VDD_EXT
PB_00
InOut
A
PullDown
none
none
VDD_EXT
PB_01
InOut
A
PullDown
none
none
VDD_EXT
PB_02
InOut
A
PullDown
none
none
VDD_EXT
PB_03
InOut
A
PullDown
none
none
VDD_EXT
PB_04
InOut
A
PullDown
none
none
VDD_EXT
PB_05
InOut
A
PullDown
none
none
VDD_EXT
PB_06
InOut
A
PullDown
none
none
VDD_EXT
PB_07
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 69 of 168 |
June 2016
Description
and Notes
Desc: PORTA Position 14 | EMAC0
PTP Pulse-Per-Second Output 3 |
SINC0 Data 0 | SMC0 Address 10
Notes: No notes
Desc: PORTA Position 15 | EMAC0
PTP Pulse-Per-Second Output 2 |
SINC0 Data 1 | SMC0 Address 9
Notes: No notes
Desc: PORTB Position 0 | EMAC0
PTP Pulse-Per-Second Output 1 |
EPPI0 Data 14 | SINC0 Data 2 |
SMC0 Address 8 | TIMER0
Alternate Clock 3
Notes: No notes
Desc: PORTB Position 1 | EMAC0
PTP Pulse-Per-Second Output 0 |
EPPI0 Data 15 | SINC0 Clock 0 |
SMC0 Address 7 | TIMER0
Alternate Clock 4
Notes: No notes
Desc: PORTB Position 2 | EMAC0
PTP Clock Input 0 | EPPI0 Data 16
| SMC0 Address 4 | UART1
Transmit
Notes: No notes
Desc: PORTB Position 3 | EMAC0
PTP Auxiliary Trigger Input 0 |
EPPI0 Data 17 | SMC0 Address 3 |
UART1 Receive | TIMER0
Alternate Capture Input 1
Notes: No notes
Desc: PORTB Position 4 | EPPI0
Data 12 | MLB0 Single-Ended
Clock | SINC0 Data 3 | SMC0
Asynchronous Ready | EMAC0
PTP Auxiliary Trigger Input 1
Notes: No notes
Desc: PORTB Position 5 | EPPI0
Data 13 | MLB0 Single-Ended
Signal | SMC0 Address 1 | EMAC0
PTP Auxiliary Trigger Input 2
Notes: No notes
Desc: PORTB Position 6 | MLB0
Single-Ended Data | PWM0
Channel B High Side | SMC0
Address 2 | EMAC0 PTP Auxiliary
Trigger Input 3
Notes: No notes
Desc: PORTB Position 7 | LP1 Data
0 | PWM0 Channel A High Side |
SMC0 Data 15 | TIMER0 Timer 3
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PB_08
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PB_09
InOut
A
PullDown
none
none
VDD_EXT
PB_10
InOut
A
PullDown
none
none
VDD_EXT
PB_11
InOut
A
PullDown
none
none
VDD_EXT
PB_12
InOut
A
PullDown
none
none
VDD_EXT
PB_13
InOut
A
PullDown
none
none
VDD_EXT
PB_14
InOut
A
PullDown
none
none
VDD_EXT
PB_15
InOut
A
PullDown
none
none
VDD_EXT
PCIE0_CLKM
InOut
TBD
PullDown
none
none
VDD_PCIE
PCIE0_CLKP
InOut
TBD
PullDown
none
none
VDD_PCIE
PCIE0_REF
InOut
TBD
PullDown
none
none
VDD_PCIE
PCIE0_RXM
InOut
TBD
PullDown
none
none
VDD_PCIE_RX
PCIE0_RXP
InOut
TBD
PullDown
none
none
VDD_PCIE_RX
PCIE0_TXM
InOut
TBD
PullDown
none
none
VDD_PCIE_TX
Rev. PrG |
Page 70 of 168 |
June 2016
Description
and Notes
Desc: PORTB Position 8 | LP1 Data
1 | PWM0 Channel A Low Side |
SMC0 Data 14 | TIMER0 Timer 4
Notes: No notes
Desc: PORTB Position 9 | CAN1
Transmit | LP1 Data 2 | SMC0 Data
13
Notes: No notes
Desc: PORTB Position 10 | CAN1
Receive | LP1 Data 3 | SMC0 Data
12 | TIMER0 Timer 2 | TIMER0
Alternate Capture Input 4
Notes: No notes
Desc: PORTB Position 11 | LP1
Data 4 | PWM0 Channel D High
Side | SMC0 Data 11 | CNT0 Count
Zero Marker
Notes: No notes
Desc: PORTB Position 12 | LP1
Data 5 | PWM0 Channel D Low
Side | SMC0 Data 10 | CNT0 Count
Up and Direction
Notes: No notes
Desc: PORTB Position 13 | LP1
Data 6 | PWM0 Channel C High
Side | SMC0 Data 9
Notes: No notes
Desc: PORTB Position 14 | LP1
Data 7 | PWM0 Channel C Low
Side | SMC0 Data 8 | TIMER0
Timer 5 | CNT0 Count Down and
Gate
Notes: No notes
Desc: PORTB Position 15 | LP1
Acknowledge | PWM0 Shutdown
Input 0 | SMC0 Write Enable |
TIMER0 Timer 1
Notes: No notes
Desc: PCIE0 CLK Notes: No notes
Desc: PCIE0 CLK +
Notes: No notes
Desc: PCIE0 Reference
Notes: No notes
Desc: PCIE0 RX Notes: No notes
Desc: PCIE0 RX +
Notes: No notes
Desc: PCIE0 TX Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PCIE0_TXP
Type
InOut
Driver
Type
TBD
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_PCIE_TX
PC_00
InOut
A
PullDown
none
none
VDD_EXT
PC_01
InOut
A
PullDown
none
none
VDD_EXT
PC_02
InOut
A
PullDown
none
none
VDD_EXT
PC_03
InOut
A
PullDown
none
none
VDD_EXT
PC_04
InOut
A
PullDown
none
none
VDD_EXT
PC_05
InOut
A
PullDown
none
none
VDD_EXT
PC_06
InOut
A
PullDown
none
none
VDD_EXT
PC_07
InOut
A
PullDown
none
none
VDD_EXT
PC_08
InOut
A
PullDown
none
none
VDD_EXT
PC_09
InOut
A
PullDown
none
none
VDD_EXT
PC_10
InOut
A
PullDown
none
none
VDD_EXT
PC_11
InOut
A
PullDown
none
none
VDD_EXT
PC_12
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 71 of 168 |
June 2016
Description
and Notes
Desc: PCIE0 TX +
Notes: No notes
Desc: PORTC Position 0 | LP1
Clock | PWM0 Channel B Low
Side | SMC0 Read Enable | SPI0
Slave Select Output 4
Notes: No notes
Desc: PORTC Position 1 | SPI2
Clock
Notes: No notes
Desc: PORTC Position 2 | SPI2
Master In, Slave Out
Notes: No notes
Desc: PORTC Position 3 | SPI2
Master Out, Slave In
Notes: No notes
Desc: PORTC Position 4 | SPI2
Data 2
Notes: No notes
Desc: PORTC Position 5 | SPI2
Data 3
Notes: No notes
Desc: PORTC Position 6 | SPI2
Slave Select Output 1 | SPI2 Slave
Select Input
Notes: No notes
Desc: PORTC Position 7 | CAN0
Receive | SMC0 Memory Select 2
| SPI0 Slave Select Output 1 |
TIMER0 Alternate Capture Input
3
Notes: No notes
Desc: PORTC Position 8 | CAN0
Transmit | SMC0 Memory Select
3
Notes: No notes
Desc: PORTC Position 9 | SPI0
Clock
Notes: No notes
Desc: PORTC Position 10 | SPI0
Master In, Slave Out
Notes: No notes
Desc: PORTC Position 11 | SPI0
Master Out, Slave In | TIMER0
Clock
Notes: No notes
Desc: PORTC Position 12 | ACM0
External Trigger n | SMC0
Address 25 | SPI0 Ready | SPI0
Slave Select Output 3
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PC_13
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PC_14
InOut
A
PullDown
none
none
VDD_EXT
PC_15
InOut
A
PullDown
none
none
VDD_EXT
PD_00
InOut
A
PullDown
none
none
VDD_EXT
PD_01
InOut
A
PullDown
none
none
VDD_EXT
PD_02
InOut
A
PullDown
none
none
VDD_EXT
PD_03
InOut
A
PullDown
none
none
VDD_EXT
PD_04
InOut
A
PullDown
none
none
VDD_EXT
PD_05
InOut
A
PullDown
none
none
VDD_EXT
PD_06
InOut
A
PullDown
none
none
VDD_EXT
PD_07
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 72 of 168 |
June 2016
Description
and Notes
Desc: PORTC Position 13 | ACM0
ADC Control Signals | SPI1 Slave
Select Output 1 | UART0 Transmit
Notes: No notes
Desc: PORTC Position 14 | ACM0
ADC Control Signals | UART0
Receive | TIMER0 Alternate
Capture Input 0
Notes: No notes
Desc: PORTC Position 15 | ACM0
ADC Control Signals | EPPI0
Frame Sync 3 (FIELD) | SMC0
Memory Select 0 | UART0
Request to Send
Notes: No notes
Desc: PORTD Position 0 | ACM0
ADC Control Signals | EPPI0 Data
23 | SMC0 Data 7 | UART0 Clear to
Send
Notes: No notes
Desc: PORTD Position 1 | ACM0
ADC Control Signals | SMC0
Output Enable | SPI0 Slave Select
Output 2 | SPI0 Slave Select Input
Notes: No notes
Desc: PORTD Position 2 | LP0
Data 0 | PWM1 Shutdown Input 0
| TRACE0 Trace Data 0
Notes: No notes
Desc: PORTD Position 3 | LP0
Data 1 | PWM1 Channel A High
Side | TRACE0 Trace Data 1
Notes: No notes
Desc: PORTD Position 4 | LP0
Data 2 | PWM1 Channel A Low
Side | TRACE0 Trace Data 2
Notes: No notes
Desc: PORTD Position 5 | LP0
Data 3 | PWM1 Channel B High
Side | TRACE0 Trace Data 3
Notes: No notes
Desc: PORTD Position 6 | LP0
Data 4 | PWM1 Channel B Low
Side | TRACE0 Trace Data 4
Notes: No notes
Desc: PORTD Position 7 | LP0
Data 5 | PWM1 Channel C High
Side | TRACE0 Trace Data 5
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PD_08
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PD_09
InOut
A
PullDown
none
none
VDD_EXT
PD_10
InOut
A
PullDown
none
none
VDD_EXT
PD_11
InOut
A
PullDown
none
none
VDD_EXT
PD_12
InOut
A
PullDown
none
none
VDD_EXT
PD_13
InOut
A
PullDown
none
none
VDD_EXT
PD_14
InOut
A
PullDown
none
none
VDD_EXT
PD_15
InOut
A
PullDown
none
none
VDD_EXT
PE_00
InOut
A
PullDown
none
none
VDD_EXT
PE_01
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 73 of 168 |
June 2016
Description
and Notes
Desc: PORTD Position 8 | LP0
Data 6 | PWM1 Channel C Low
Side | TRACE0 Trace Data 6 |
TIMER0 Alternate Clock 1
Notes: No notes
Desc: PORTD Position 9 | LP0
Data 7 | PWM1 Channel D High
Side | TRACE0 Trace Data 7 |
TIMER0 Alternate Clock 2
Notes: No notes
Desc: PORTD Position 10 | LP0
Clock | PWM1 Channel D Low
Side | TRACE0 Trace Clock
Notes: No notes
Desc: PORTD Position 11 | LP0
Acknowledge | PWM1 PWMTMR
Grouped
Notes: No notes
Desc: PORTD Position 12 | EPPI0
Data 19 | SMC0 Address 6 | UART2
Transmit
Notes: No notes
Desc: PORTD Position 13 | EPPI0
Data 18 | SMC0 Address 5 | UART2
Receive | TIMER0 Alternate
Capture Input 2
Notes: No notes
Desc: PORTD Position 14 | EPPI0
Data 11 | MLB0 Single-Ended
Clock Out | PWM2 Shutdown
Input 0 | SMC0 Data 6
Notes: No notes
Desc: PORTD Position 15 | EPPI0
Data 10 | PWM2 Channel C High
Side | SMC0 Data 5
Notes: No notes
Desc: PORTE Position 0 | EPPI0
Data 9 | PWM2 Channel C Low
Side | SMC0 Data 4
Notes: No notes
Desc: PORTE Position 1 | EPPI0
Frame Sync 2 (VSYNC) | SPI0
Slave Select Output 5 | SHARC
Core 1 Flag Pin | UART1 Clear to
Send
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PE_02
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PE_03
InOut
A
PullDown
none
none
VDD_EXT
PE_04
InOut
A
PullDown
none
none
VDD_EXT
PE_05
InOut
A
PullDown
none
none
VDD_EXT
PE_06
InOut
A
PullDown
none
none
VDD_EXT
PE_07
InOut
A
PullDown
none
none
VDD_EXT
PE_08
InOut
A
PullDown
none
none
VDD_EXT
PE_09
InOut
A
PullDown
none
none
VDD_EXT
PE_10
InOut
A
PullDown
none
none
VDD_EXT
PE_11
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 74 of 168 |
June 2016
Description
and Notes
Desc: PORTE Position 2 | EPPI0
Frame Sync 1 (HSYNC) | SPI0
Slave Select Output 6 | SHARC
Core 2 Flag Pin | UART1 Request
to Send
Notes: No notes
Desc: PORTE Position 3 | EPPI0
Clock | SPI0 Slave Select Output
7 | SPI2 Slave Select Output 2 |
SHARC Core 1 Flag Pin
Notes: No notes
Desc: PORTE Position 4 | EPPI0
Data 8 | PWM2 Channel D High
Side | SPI2 Slave Select Output 3
| SHARC Core 2 Flag Pin
Notes: No notes
Desc: PORTE Position 5 | EPPI0
Data 7 | PWM2 PWMTMR
Grouped | SPI2 Slave Select
Output 4 | SHARC Core 1 Flag Pin
Notes: No notes
Desc: PORTE Position 6 | EPPI0
Data 6 | SPI2 Slave Select Output
5 | SHARC Core 2 Flag Pin
Notes: No notes
Desc: PORTE Position 7 | EPPI0
Data 5 | SPI1 Slave Select Output
2 | SHARC Core 1 Flag Pin
Notes: No notes
Desc: PORTE Position 8 | EPPI0
Data 4 | SPI1 Ready | SPI1 Slave
Select Output 5 | SHARC Core 2
Flag Pin
Notes: No notes
Desc: PORTE Position 9 | EPPI0
Data 3 | PWM0 PWMTMR
Grouped | SMC0 Data 3 | TIMER0
Timer 0
Notes: No notes
Desc: PORTE Position 10 | EPPI0
Data 2 | PWM2 Channel D Low
Side | SMC0 Data 2 | UART2
Request to Send
Notes: No notes
Desc: PORTE Position 11 | EPPI0
Data 1 | SMC0 Data 1 | SPI1 Slave
Select Output 3 | UART2 Clear to
Send | SPI1 Slave Select Input
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PE_12
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PE_13
InOut
A
PullDown
none
none
VDD_EXT
PE_14
InOut
A
PullDown
none
none
VDD_EXT
PE_15
InOut
A
PullDown
none
none
VDD_EXT
PF_00
InOut
A
PullDown
none
none
VDD_EXT
PF_01
InOut
A
PullDown
none
none
VDD_EXT
PF_02
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_03
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_04
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_05
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_06
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_07
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
Rev. PrG |
Page 75 of 168 |
June 2016
Description
and Notes
Desc: PORTE Position 12 | EPPI0
Data 0 | SMC0 Data 0 | SPI1 Slave
Select Output 4 | SPI2 Ready
Notes: No notes
Desc: PORTE Position 13 | EPPI0
Data 20 | SMC0 Memory Select 1
| SPI1 Clock
Notes: No notes
Desc: PORTE Position 14 | EPPI0
Data 21 | SMC0 Byte Enable 0 |
SPI1 Master In, Slave Out
Notes: No notes
Desc: PORTE Position 15 | EPPI0
Data 22 | SMC0 Byte Enable 1 |
SPI1 Master Out, Slave In
Notes: No notes
Desc: PORTF Position 0 | SPI1
Slave Select Output 6 | TIMER0
Timer 6
Notes: No notes
Desc: PORTF Position 1 | SPI1
Slave Select Output 7 | TIMER0
Timer 7
Notes: No notes
Desc: PORTF Position 2 | HADC0
End of Conversion / Serial Data
Out | MSI0 Data 0
Notes: No notes
Desc: PORTF Position 3 | HADC0
Controls to external multiplexer
| MSI0 Data 1
Notes: No notes
Desc: PORTF Position 4 | HADC0
Controls to external multiplexer
| MSI0 Data 2
Notes: No notes
Desc: PORTF Position 5 | HADC0
Controls to external multiplexer
| MSI0 Data 3
Notes: No notes
Desc: PORTF Position 6 | MSI0
Data 4 | PWM2 Channel A Low
Side
Notes: No notes
Desc: PORTF Position 7 | MSI0
Data 5 | PWM2 Channel A High
Side
Notes: No notes
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PF_08
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown/Progra none
mmable PullUp
none
Power Domain
VDD_EXT
PF_09
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_10
InOut
A
PullDown/Progra none
mmable PullUp
none
VDD_EXT
PF_11
InOut
A
PullDown
none
none
VDD_EXT
PF_12
InOut
A
PullDown
none
none
VDD_EXT
PF_13
InOut
A
PullDown
none
none
VDD_EXT
PF_14
InOut
A
PullDown
none
none
VDD_EXT
PF_15
InOut
A
PullDown
none
none
VDD_EXT
PG_00
InOut
A
PullDown
none
none
VDD_EXT
PG_01
InOut
A
PullDown
none
none
VDD_EXT
PG_02
InOut
A
PullDown
none
none
VDD_EXT
PG_03
InOut
A
PullDown
none
none
VDD_EXT
Rev. PrG |
Page 76 of 168 |
June 2016
Description
and Notes
Desc: PORTF Position 8 | MSI0
Data 6 | PWM2 Channel B Low
Side
Notes: No notes
Desc: PORTF Position 9 | MSI0
Data 7 | PWM2 Channel B High
Side
Notes: No notes
Desc: PORTF Position 10 | MSI0
Command
Notes: No notes
Desc: PORTF Position 11 | MSI0
Clock
Notes: No notes
Desc: PORTF Position 12 | MSI0
Card Detect
Notes: No notes
Desc: PORTF Position 13 | EMAC1
Carrier Sense/RMII Receive Data
Valid | MSI0 eSDIO Interrupt
Input | TRACE0 Trace Data |
TRACE0 Trace Data 8
Notes: No notes
Desc: PORTF Position 14 | EMAC1
Management Channel Clock |
TRACE0 Trace Data | TRACE0
Trace Data 9
Notes: No notes
Desc: PORTF Position 15 | EMAC1
Management Channel Serial
Data | TRACE0 Trace Data |
TRACE0 Trace Data 10
Notes: No notes
Desc: PORTG Position 0 | EMAC1
Reference Clock | TRACE0 Trace
Clock
Notes: No notes
Desc: PORTG Position 1 | EMAC1
Transmit Enable | TRACE0 Trace
Data | TRACE0 Trace Data 11
Notes: No notes
Desc: PORTG Position 2 | EMAC1
Transmit Data 0 | TRACE0 Trace
Data | TRACE0 Trace Data 12
Notes: No notes
Desc: PORTG Position 3 | EMAC1
Transmit Data 1 | TRACE0 Trace
Data | TRACE0 Trace Data 13
Notes: No notes
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
PG_04
Type
InOut
Driver
Type
A
Int
Term
Reset
Term
Reset
Drive
PullDown
none
none
Power Domain
VDD_EXT
PG_05
InOut
A
PullDown
none
none
VDD_EXT
RTC0_CLKIN
a
NA
none
none
none
VDD_RTC
RTC0_XTAL
a
NA
none
none
none
VDD_RTC
SYS_BMODE0
Input
NA
PullDown
none
none
VDD_EXT
SYS_BMODE1
Input
NA
PullDown
none
none
VDD_EXT
SYS_BMODE2
Input
NA
PullDown
none
none
VDD_EXT
SYS_CLKIN0
a
NA
none
none
none
VDD_EXT
SYS_CLKIN1
a
NA
none
none
none
VDD_EXT
SYS_CLKOUT
a
A
none
none
none
SYS_FAULT
InOut
A
none
none
none
SYS_FAULT
InOut
A
none
none
none
SYS_HWRST
Input
NA
none
none
none
VDD_EXT
SYS_RESOUT
Output
A
none
none
L
VDD_EXT
SYS_XTAL0
a
NA
none
none
none
VDD_EXT
SYS_XTAL1
a
NA
none
none
none
VDD_EXT
TWI0_SCL
InOut
D
none
none
none
VDD_EXT
Rev. PrG |
Page 77 of 168 |
June 2016
Description
and Notes
Desc: PORTG Position 4 | EMAC1
Receive Data 0 | TRACE0 Trace
Data | TRACE0 Trace Data 14
Notes: No notes
Desc: PORTG Position 5 | EMAC1
Receive Data 1 | TRACE0 Trace
Data | TRACE0 Trace Data 15
Notes: No notes
Desc: RTC0 Crystal input /
external oscillator connection
Notes: Connect to GND if not
used
Desc: RTC0 Crystal output
Notes: No notes
Desc: Boot Mode Control n
Notes: No notes
Desc: Boot Mode Control n
Notes: No notes
Desc: Boot Mode Control n
Notes: No notes
Desc: Clock/Crystal Input
Notes: No notes
Desc: Clock/Crystal Input
Notes: Connect to GND if not
used
Desc: Processor Clock Output
Notes: No notes
Desc: Active-High Fault Output
Notes: External pull-down
required to keep signal in deasserted state
Desc: Active-Low Fault Output
Notes: External pull-up required
to keep signal in de-asserted
state
Desc: Processor Hardware Reset
Control
Notes: No notes
Desc: Reset Output
Notes: No notes
Desc: Crystal Output
Notes: No notes
Desc: Crystal Output
Notes: No notes
Desc: TWI0 Serial Clock
Notes: Add external pull-up if
used. Can be pulled low when
not used.
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Signal Name
TWI0_SDA
Type
InOut
Driver
Type
D
Int
Term
Reset
Term
Reset
Drive
none
none
none
Power Domain
VDD_EXT
TWI1_SCL
InOut
D
none
none
none
VDD_EXT
TWI1_SDA
InOut
D
none
none
none
VDD_EXT
TWI2_SCL
InOut
D
none
none
none
VDD_EXT
TWI2_SDA
InOut
D
none
none
none
VDD_EXT
USB0_DM
InOut
F
none
none
none
VDD_USB
USB0_DP
InOut
F
none
none
none
VDD_USB
USB0_ID
InOut
none
none
none
VDD_USB
USB0_VBC
InOut
E
none
none
none
VDD_USB
USB0_VBUS
InOut
G
none
none
none
VDD_USB
USB1_DM
InOut
F
none
none
none
VDD_USB
USB1_DP
InOut
F
none
none
none
VDD_USB
USB1_VBUS
InOut
G
none
none
none
VDD_USB
USB_CLKIN
a
none
none
none
Rev. PrG |
Page 78 of 168 |
June 2016
Description
and Notes
Desc: TWI0 Serial Data
Notes: Add external pull-up if
used. Can be pulled low when
not used.
Desc: TWI1 Serial Clock
Notes: Add external pull-up if
used. Can be pulled low when
not used.
Desc: TWI1 Serial Data
Notes: Add external pull-up if
used. Can be pulled low when
not used.
Desc: TWI2 Serial Clock
Notes: Add external pull-up if
used. Can be pulled low when
not used.
Desc: TWI2 Serial Data
Notes: Add external pull-up if
used. Can be pulled low when
not used.
Desc: USB0 Data Notes: Add external pull-down if
not used
Desc: USB0 Data +
Notes: Add external pull-down if
not used
Desc: USB0 OTG ID
Notes: Connect to GND when
USB is not used
Desc: USB0 VBUS Control
Notes: Add external pull-down if
not used
Desc: USB0 Bus Voltage
Notes: Connect to GND if not
used
Desc: USB1 Data Notes: Add external pull-down if
not used
Desc: USB1 Data +
Notes: Add external pull-down if
not used
Desc: USB1 Bus Voltage
Notes: Connect to GND if not
used
Desc: USB0/USB1 Clock/Crystal
Input
Notes: Services both USB0 and
USB1. Connect to GND if not
used.
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 27. ADSP-SC58x/ADSP-2158x Designer Quick Reference (Continued)
Int
Term
Reset
Term
Reset
Drive
none
none
none
NA
none
none
none
s
NA
none
none
none
VDD_HADC
s
NA
none
none
none
VDD_INT
s
NA
none
none
none
VDD_PCIE
s
NA
none
none
none
VDD_PCIE_RX
s
NA
none
none
none
VDD_PCIE_TX
s
NA
none
none
none
VDD_RTC
s
NA
none
none
none
VDD_USB
s
NA
none
none
none
Signal Name
USB_XTAL
Type
a
VDD_DMC
s
VDD_EXT
Driver
Type
Rev. PrG |
Page 79 of 168 |
Power Domain
June 2016
Description
and Notes
Desc: USB0/USB1 Crystal
Notes: Services both USB0 and
USB1
Desc: DMC VDD
Notes: No notes
Desc: External Voltage Domain
Notes: No notes
Desc: HADC VDD
Notes: No notes
Desc: Internal Voltage Domain
Notes: No notes
Desc: PCIE Supply Voltage
Notes: Connect to GND if not
used
Desc: PCIE RX Supply Voltage
Notes: Connect to GND if not
used
Desc: PCIE TX Supply Voltage
Notes: Connect to GND if not
used
Desc: RTC VDD
Notes: No notes
Desc: USB VDD
Notes: Connect to VDD_EXT
when USB is not used
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
SPECIFICATIONS
For information about product specifications please contact your Analog Devices, Inc. representative.
OPERATING CONDITIONS
Parameter1
Conditions
Min
Nominal
Max
Unit
Internal (Core) Supply Voltage
External (I/O) Supply Voltage
Analog Power Supply Voltage
DDR2/LPDDR Controller Supply Voltage
DDR3 Controller Supply Voltage
USB Supply Voltage
VDD_USB3
RTC Voltage
VDD_RTC
PCIe Core Transmit Voltage
VDD_PCIE_TX
PCIe Core Receive Voltage
VDD_PCIE_RX
PCIe Voltage
VDD_PCIE
VDDR_VREF
DDR2 Reference Voltage
HADC Reference Voltage
VHADC_REF4
5
High Level Input Voltage
VIH
VIL5
Low Level Input Voltage
Low Level Input Voltage
VIL_DDR2/36
High Level Input Voltage
VIH_DDR2/36
7
VIL_LPDDR
Low Level Input Voltage
High Level Input Voltage
VIH_LPDDR7
Junction Temperature 349-Lead CSP_BGA
TJ
TJ
Junction Temperature 349-Lead CSP_BGA
Junction Temperature 529-Lead CSP_BGA
TJ
Junction Temperature 529-Lead CSP_BGA
TJ
AUTOMOTIVE USE ONLY
Junction Temperature 349-Lead CSP_BGA
TJ8
(Automotive Grade)
CCLK ≤ 450 MHz
1.05
3.13
3.13
1.7
1.425
3.13
3.13
1.05
1.05
3.13
0.49 × VDD_DMC
2.5
2.0
1.1
3.3
3.3
1.8
1.5
3.3
3.3
1.1
1.1
3.3
0.50 × VDD_DMC
3.30
1.15
3.47
3.47
1.9
1.575
3.47
3.47
1.15
1.15
3.47
0.51 × VDD_DMC
VDD_HADC
100
125
110
125
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
°C
°C
°C
°C
133
°C
VDD_INT
VDD_EXT
VDD_HADC
VDD_DMC2
VDD_EXT = Maximum
VDD_EXT = Minimum
VDD_DMC = Minimum
VDD_DMC = Maximum
VDD_DMC = Minimum
VDD_DMC = Maximum
TAMBIENT 0°C to +70°C
TAMBIENT –40°C to +95°C
TAMBIENT 0°C to +70°C
TAMBIENT –40°C to +85°C
0.8
VREF – 0.25
VREF + 0.25
0.2 × VDD_DMC
0.8 × VDD_DMC
0
–40
0
–40
TAMBIENT –40°C to +105°C –40
1
Specifications subject to change without notice.
Applies to DDR2/DDR3/LPDDR signals.
3
If not used, VDD_USB should be connected to 3.3V.
4
VHADC_VREF should always be less than VDD_HADC.
5
Parameter value applies to all input and bidirectional pins except all the TWI, DMC, USB, PCIe, and MLB pins.
6
This parameter applies to all DMC0/1 signals in DDR2/DDR3 mode. VREF is the voltage applied to pin VREF_DMC, nominally VDD_DMC/2.
7
This parameter applies to DMC0/1 signals in LPDDR mode.
8
Automotive temperature grade product only. Contact Analog Devices for more information.
2
Table 28. TWI_VSEL Selections and VDD_EXT/VBUSTWI
TWI000
TWI100
1
1
VDD_EXT Nominal
VBUSTWI Min
VBUSTWI Nominal
VBUSTWI Max
Unit
3.30
3.13
3.30
3.47
V
3.30
4.75
5.00
5.25
V
Designs must comply with the VDD_EXT and VBUSTWI voltages specified for the default TWI_DT setting for correct JTAG boundary scan operation during reset.
Rev. PrG |
Page 80 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Clock Related Operating Conditions
Table 29 describes the core clock, system clock, and peripheral clock timing requirements. The data presented in the tables applies to all
speed grades except where expressly noted.
Table 29. Clock Operating Conditions
Parameter
Restriction
fCCLK
Core Clock Frequency
fSYSCLK
SYSCLK Frequency
fSCLK0
SCLK0 Frequency1
fSYSCLK ≥ fSCLK0
fSCLK1
SCLK1 Frequency
fSYSCLK ≥ fSCLK1
fDCLK
fDCLK
Min
Typ
fCCLK ≥ fSYSCLK
Max
Unit
450
MHz
225
MHz
112.5
MHz
112.5
MHz
LPDDR Clock Frequency
200
MHz
DDR2 Clock Frequency
400
MHz
fDCLK
DDR3 Clock Frequency
450
MHz
fOCLK
Output Clock Frequency
TBD
MHz
fSYS_CLKOUTJ SYS_CLKOUT Period Jitter
2, 3
30
±1
%
fPCLKPROG
Programmed PPI Clock When Transmitting Data and Frame Sync
75
MHz
fPCLKPROG
Programmed PPI Clock When Receiving Data or Frame Sync
45
MHz
fPCLKEXT ≤ fSCLK1
75
MHz
fPCLKEXT ≤ fSCLK1
45
MHz
150
MHz
fPCLKEXT
External PPI Clock When Receiving Data and Frame Sync
fPCLKEXT
External PPI Clock Transmitting Data or Frame Sync4, 5
fLCLKTPROG
Programmed Link Port Transmit Clock
fLCLKREXT
External Link Port Receive Clock
4, 5
4, 5
150
MHz
fSPTCLKPROG Programmed SPT Clock When Transmitting Data and Frame Sync
fLCLKEXT ≤ fCLKO8
56.25
MHz
fSPTCLKPROG Programmed SPT Clock When Receiving Data or Frame Sync
28.125
MHz
4, 5
fSPTCLKEXT
External SPT Clock When Receiving Data and Frame Sync
fSPTCLKEXT
External SPT Clock Transmitting Data or Frame Sync4, 5
fSPTCLKEXT ≤ fSCLK0
56.25
MHz
fSPTCLKEXT ≤ fSCLK0
28.125
MHz
fSPICLKPROG
Programmed SPI Clock When Transmitting Data
75
MHz
fSPICLKPROG
Programmed SPI Clock When Receiving Data
75
MHz
fSPICLKEXT
External SPI Clock When Receiving Data4, 5
fSPICLKEXT ≤ fSCLK1
75
MHz
fSPICLKEXT
External SPI Clock When Transmitting Data4, 5
fSPICLKEXT ≤ fSCLK1
45
MHz
fACLKPROG
Programmed ACM Clock
56.25
MHz
1
The minimum frequency for SCLK0 applies only when the USB is used.
SYS_CLKOUT jitter is dependent on the application system design including pin switching activity, board layout, and the jitter characteristics of the SYS_CLKIN source.
Due to the dependency on these factors the measured jitter may be higher or lower than this typical specification for each end application.
3
The value in the Typ field is the percentage of the SYS_CLKOUT period.
4
The maximum achievable frequency for any peripheral in external clock mode is dependent on being able to meet the setup and hold times in the AC timing specifications
section for that peripheral. Pay particular attention to setup and hold times for VDD_EXT = 1.8 V which may preclude the maximum frequency listed here.
5
The peripheral external clock frequency must also be less than or equal to the fSCLK (fSCLK0 or fSCLK1) that clocks the peripheral.
2
Rev. PrG |
Page 81 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Table 30. Phase-Locked Loop Operating Conditions
Parameter
fPLLCLK
Min
250
PLL Clock Frequency
CSEL
(1-31)
SYSSEL
(1-31)
SYS_CLKIN
PLL
Max
900
CCLK
S0SEL
(1-7)
SCLK0
S1SEL
(1-7)
SCLK1
SYSCLK
PLLCLK
DSEL
(1-31)
DCLK
OSEL
(1-127)
OUTCLK
Figure 8. Clock Relationships and Divider Values
Rev. PrG |
Page 82 of 168 |
June 2016
Unit
MHz
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ELECTRICAL CHARACTERISTICS
450 MHz
Parameter1
2
VOH
2
VOL
VOH_DDR24
VOL_DDR24
VOH_DDR24
VOL_DDR24
VOH_DDR35
VOL_DDR35
VOH_DDR35
VOL_DDR35
VOH_LPDDR6
VOL_LPDDR6
IIH7, 8
IIL7
IIL_PU8
IIH_PD9
IOZH10
IOZL10
IDD_INT11
CIN12
IDD_IDLE
Description
Conditions
Min
3
High Level Output Voltage
Low Level Output Voltage
High Level Output Voltage
for DDR2 DS = 40 ohm
Low Level Output Voltage
for DDR2 DS = 40 ohm
High Level Output Voltage
for DDR2 DS = 60 ohm
Low Level Output Voltage
for DDR2 DS = 60 ohm
High Level Output Voltage
for DDR3 DS = 40 ohm
Low Level Output Voltage
for DDR3 DS = 60 ohm
@ VDD_EXT = Min, IOH = –1.0 mA
@ VDD_EXT = Min, IOL = 1.0 mA3
@ VDD_DDR = Min, IOH = –7.0 mA
High Level Output Voltage
for DDR3 DS = 60 ohm
Low Level Output Voltage
for DDR3 DS = 60 ohm
High Level Output Voltage
for LPDDR
Low Level Output Voltage
for LPDDR
High Level Input Current
@ VDD_DDR = Min, IOH = –5.0 mA
Low Level Input Current
Low Level Input Current
Pull-up
High Level Input Current
Pull-down
Three-State Leakage
Current
Three-State Leakage
Current
Supply Current (Internal)
Input Capacitance
VDD_INT Current in Idle
Typ
Max
Unit
0.4
V
V
V
0.32
V
2.4
1.38
@ VDD_DDR = Min, IOL = 7.0 mA
@ VDD_DDR = Min, IOH = –5.0 mA
1.38
V
@ VDD_DDR = Min, IOL = 5.0 mA
0.32
@ VDD_DDR = Min, IOH = –7.0 mA
1.105
V
@ VDD_DDR = Min, IOL = 5.0 mA
0.32
1.105
V
V
@ VDD_DDR = Min, IOL = 5.0 mA
0.32
@ VDD_DDR = Min, IOH = –9.0 mA
V
1.38
V
V
@ VDD_DDR = Min, IOL = 9.0 mA
0.32
V
@ VDD_EXT = Max,
VIN = VDD_EXT Max
@ VDD_EXT = Max, VIN = 0 V
@ VDD_EXT = Max, VIN = 0 V
10
μA
10
200
μA
μA
@ VDD_EXT = Max, VIN = 0 V
200
μA
@ VDD_EXT/VDD_DDR = Max,
VIN = VDD_EXT/VDD_DDR Max
@ VDD_EXT/VDD_DDR = Max,
VIN = 0 V
fCCLK > 0 MHz
TCASE = 25°C
fCCLK = 450 MHz
ASFSHARC1 = 0.27
ASFSHARC2 = 0.27
ASFA5 = 0.07
fSYSCLK = 225 MHz
fSCLK0/1 = 112.5 MHz
(Other clocks are disabled)
No Peripheral or DMA activity
TJ = 25°C
VDD_INT = 1.1 V
10
μA
10
μA
TBD
5
mA
pF
Rev. PrG |
Page 83 of 168 |
435
June 2016
mA
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
450 MHz
Parameter1
Description
Conditions
IDD_TYP
VDD_INT Current
IDD_INT
VDD_INT Current
fCCLK = 450 MHz
ASFSHARC1 = 1.0
ASFSHARC2 = 1.0
ASFA5 = 0.64
fSYSCLK = 225 MHz
fSCLK0/1 = 112.5 MHz
(Other clocks are disabled)
FFT accelerator operating at fSYSCLK/4
DMA data rate = 500 MB/s
TJ = 25°C
VDD_INT = 1.1 V
fCCLK 0 MHz
fSCLK0/1  0 MHz
Min
1
Typ
Max
1100
Unit
mA
See
IDDINT_TOT
equation
mA
Specifications subject to change without notice.
Applies to all output and bidirectional pins except TWI, DMC, USB, PCIe, and MLB.
3
See Output Drive Currents for typical drive current capabilities.
4
Applies to all DMC output and bidirectional signals in DDR2 mode.
5
Applies to all DMC output and bidirectional signals in DDR3 mode.
6
Applies to all DMC output and bidirectional signals in LPDDR mode.
7
Applies to input pins: SYS_BMODE0-2, SYS_CLKIN0, SYS_CLKIN1, SYS_HWRST, JTG_TDI, JTG_TMS, and USB0_CLKIN.
8
Applies to input pins with internal pull-ups: JTG_TDI, JTG_TMS, and JTG_TCK.
9
Applies to signals: JTAG_TRST, USB0_VBUS, USB1_VBUS.
10
Applies to signals: PA0-15, PB0-15, PC0-15, PD0-15, PE0-15, PF0-15, PG0-5, DAI0_PINx, DAI1_PINx, DMC0_DQx, DMC0_LDQS, DMC0_UDQS, DMC0_LDQS,
DMC0_UDQS, SYS_FAULT, SYS_FAULT, JTG_TDO, USB0_ID, USBx_DM, USBx_DP, and USBx_VBC.
11
See Engineer-to-Engineer Note EE-TBD “Estimating Power Dissipation for ADSP-215xx SHARC Processors” for further information.
12
Applies to all signal pins.
2
Rev. PrG |
Page 84 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Total Internal Power Dissipation
Application-Dependent Current
Total power dissipation has two components:
The application-dependent currents include the dynamic current in the core clock domain of the two SHARC+ cores and the
ARM Cortex-A5 core and accelerator currents.
1. Static, including leakage current
2. Dynamic, due to transistor switching characteristics for
each clock domain
Many operating conditions can also affect power dissipation,
including temperature, voltage, operating frequency, and processor activity. The following equation describes the internal
current consumption.
IDDINT_TOT = IDDINT_STATIC + IDDINT_CCLK_SHARC1_DYN +
IDDINT_CCLK_SHARC2_DYN + IDDINT_CCLK_A5_DYN +
IDDINT_DCLK_DYN + IDDINT_SYSCLK_DYN + IDDINT_SCLK0_DYN +
IDDINT_SCLK1_DYN + IDDINT_OCLK_DYN + IDDINT_ACCL_DYN +
IDDINT_USB_DYN + IDDINT_MLB_DYN + IDDINT_GIGE_DYN +
IDDINT_DMA_DR_DYN
IDDINT_CCLK_SHARC1_DYN = Table 34 × ASFSHARC1
IDDINT_CCLK_SHARC2_DYN = Table 34 × ASFSHARC2
IDDINT_CCLK_A5_DYN = Table 35 × ASFA5
Table 32. Activity Scaling Factors for SHARC+ Core1 and
Core2 (ASFSHARC1 and ASFSHARC2)
IDDINT_STATIC is the only item present that is part of the static
power dissipation component. IDDINT_STATIC is specified as a
function of voltage (VDD_INT) and temperature (see Table 31).
There are 13 different items that contribute to the dynamic
power dissipation. These components fall into four broad categories: application-dependent currents, clock currents, currents
from high-speed peripheral operation, and data transmission
currents.
Table 31. Static Current—IDDINT_STATIC (mA)
Core clock (CCLK) use is subject to an activity scaling factor
(ASF) that represents application code running on the processor
cores (Table 32 andTable 33). The ASF is combined with the
CCLK frequency and VDD_INT dependent data in Table 34 to
calculate this portion.
IDDINT Power Vector
ASF
IDD-IDLE
0.27
IDD-NOP
0.51
IDD-TYP_3070
0.72
IDD-TYP_5050
0.86
IDD-TYP_7030
1.00
IDD-PEAK_100
1.13
Table 33. Activity Scaling Factors for ARM Cortex-A5
Core (ASFA5)
–40
1.00
3
Voltage (VDD_INT)
1.05
1.10
1.15
4
5
6
–20
7
8
10
12
14
0
14
16
19
23
27
25
30
35
41
48
56
40
48
55
64
74
86
55
73
84
97
112
128
70
111
127
145
166
189
85
166
188
213
242
275
fCCLK (MHz)
100
239
269
304
343
388
105
268
302
340
384
115
337
378
425
125
426
477
534
133
502
560
625
TJ (°C)
1.20
8
IDDINT Power Vector
ASF
IDD-IDLE
0.07
IDD-DHRYSTONE
0.64
IDD-PEAK
1.26
Table 34. CCLK Dynamic Current per SHARC+ Core
(mA, with ASF = 1.00)
450
1.000
288
Voltage (VDD_INT)
1.050
1.100
1.150
302.4
316.8
331.2
1.200
345.6
433
400
256
268.8
281.6
294.4
307.2
478
538
350
224
235.2
246.4
257.6
268.8
599
672
300
192
201.6
211.2
220.8
230.4
700
784
250
160
168
176
184
192
200
128
134.4
140.8
147.2
153.6
150
96
100.8
105.6
110.4
115.2
100
64
67.2
70.4
73.6
76.8
Rev. PrG |
Page 85 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 35. CCLK Dynamic Current per ARM Cortex-A5
Core (mA, with ASF = 1.00)
450
1.000
49.5
Voltage (VDD_INT)
1.050
1.100
1.150
52.0
54.5
56.9
1.200
59.4
400
44.0
46.2
48.4
50.6
52.8
350
38.5
40.4
42.4
44.3
46.2
300
33.0
34.7
36.3
38.0
39.6
250
27.5
28.9
30.3
31.6
33.0
200
22.0
23.1
24.2
25.3
26.4
150
16.5
17.3
18.2
19.0
19.8
100
11.0
11.6
12.1
12.7
13.2
fCCLK (MHz)
Current from High Speed Peripheral Operation
The following modules contribute significantly to power dissipation and a single term is added when they are used.
IDDINT_USB_DYN = 20 mA (if USB enabled)
IDDINT_MLB_DYN = 10 mA (if MLB 6-pin interface is enabled)
IDDINT_GIGE_DYN = 10 mA (if Gigabit Ethernet MAC controller
is enabled)
Data Transmission Current
The data transmission current represents the power dissipated
when transmitting data. This current is proportional to the data
rate. Refer to the power calculator of this product to estimate
IDDINT_DMA_DR_DYN based on the bandwidth of the data
transfer.
The following equation is used to compute the power dissipation when the FFT accelerator is used:
IDDINT_ACCL_DYN (mA) = ASFACCL × fSYSCLK (MHz) × VDD_INT
(V)
Table 36. Activity Scaling Factors for FFT Accelerator
(ASFA5)
IDDINT Power Vector
ASFACCL
Unused
0.0
IDD-TYPP
0.4
Clock Current
The dynamic clock currents provide the total power dissipated
by all transistors switching in the clock paths. The power dissipated by each clock domain is dependent on voltage (VDD_INT),
operating frequency and a unique scaling factor.
IDDINT_SYSCLK_DYN (mA) = 0.80 × fSYSCLK (MHz) × VDD_INT (V)
IDDINT_SCLK0_DYN (mA) = 0.40 × fSCLK0 (MHz) × VDD_INT (V)
IDDINT_SCLK1_DYN (mA) = 0.04 × fSCLK1 (MHz) × VDD_INT (V)
IDDINT_DCLK_DYN (mA) = 0.14 × fDCLK (MHz) × VDD_INT (V)
IDDINT_OCLK_DYN (mA) = 0.005 × fOCLK (MHz) × VDD_INT (V)
Rev. PrG |
Preliminary Technical Data
Page 86 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ABSOLUTE MAXIMUM RATINGS
ESD SENSITIVITY
Stresses at or above those listed in Table 37 may cause permanent damage to the product. This is a stress rating only;
functional operation of the product at these or any other conditions above those indicated in the operational section of this
specification is not implied. Operation beyond the maximum
operating conditions for extended periods may affect product
reliability.
ESD (electrostatic discharge) sensitive device.
Charged devices and circuit boards can discharge
without detection. Although this product features
patented or proprietary protection circuitry, damage
may occur on devices subjected to high energy ESD.
Therefore, proper ESD precautions should be taken to
avoid performance degradation or loss of functionality.
Table 37. Absolute Maximum Ratings
Parameter
Internal (Core) Supply Voltage (VDD_INT)
External (I/O) Supply Voltage
(VDD_EXT)
DDR2/LPDDR Controller Supply
Voltage (VDD_DMC)
DDR3 Controller Supply Voltage
(VDD_DMC)
USB PHY Supply Voltage (VDD_USB)
Real Time Clock Supply Voltage
(VDD_RTC)
PCIe Transmit Supply Voltage
(VDD_PCIE_TX)
PCIe Receive Supply Voltage
(VDD_PCIE_RX)
PCIe Supply Voltage (VDD_PCIE)
HADC Supply Voltage (VDD_HADC)
HADC Reference Voltage (VHADC_REF)
DDR2/LPDDR Input Voltage
DDR3 Input Voltage
Input Voltage
Output Voltage Swing
Storage Temperature Range
Junction Temperature While Biased
PACKAGE INFORMATION
Rating
–0.33 V to +1.26 V
–0.33 V to +3.60 V
The information presented in Figure 9 and Table 39 provides
details about the package branding for the processors. For a
complete listing of product availability, see Ordering Guide on
Page 167.
–0.33 V to +1.90 V
–0.33 V to +1.60 V
–0.33 V to +3.60 V
–0.33 V to +3.60 V
a
ADSP-SC589
–0.33 V to +1.20 V
tppZccc
vvvvvv.x n.n
–0.33 V to +1.20 V
#yyww country_of_origin
–0.33 V to +3.60 V
–0.33 V to +3.60 V
–0.33 V to +3.60 V
–0.33 V to +1.90 V
–0.33 V to +1.60 V
–0.33 V to +3.60 V
–0.33 V to VDD_EXT +0.5 V
–65C to +150C
133C
Table 38. Max Duty Cycle for Input Transient Voltage1, 2
Maximum Duty Cycle (%)2
100
50
40
25
20
15
10
VIN Min (V)3
TBD
TBD
TBD
TBD
TBD
TBD
TBD
VIN Max (V)3
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Figure 9. Product Information on Package1
1
Exact brand may differ, depending on package type.
Table 39. Package Brand Information
Brand Key
ADSP-SC589
t
pp
Z
ccc
vvvvvv.x
n.n
#
yyww
1
Applies to all signal balls with the exception of SYS_CLKIN0, SYS_CLKIN1,
SYS_XTAL0, SYS_XTAL1, and all the USB, TWI, PCI, and DMC0 signals.
2
Applies only when VDD_EXT is within specifications. When VDD_EXT is
outside specifications, the range is VDD_EXT ± 0.2 V.
3
The individual values cannot be combined for analysis of a single instance of
overshoot or undershoot. The worst case observed value must fall within one of
the specified voltages, and the total duration of the overshoot or undershoot
(exceeding the 100% case) must be less than or equal to the corresponding duty
cycle.
Rev. PrG |
Page 87 of 168 |
June 2016
Field Description
Product Name
Temperature Range
Package Type
RoHS Compliant Option
See Ordering Guide
Assembly Lot Code
Silicon Revision
RoHS Compliant Designation
Date Code
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
TIMING SPECIFICATIONS
Specifications are subject to change without notice.
Power-Up Reset Timing
Table 40 and Figure 10 show the relationship between power supply startup and processor reset timing, related to the clock generation
unit (CGU) and reset control unit (RCU).
In Figure 10, VDD_SUPPLIES are VDD_INT, VDD_EXT, VDD_DMC, VDD_USB, VDD_HADC, VDD_RTC, VDD_PCI_TX, VDD_PCI_RX, and VDD_PCI_CORE.
Table 40. Power-Up Reset Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirement
tRST_IN_PWR
SYS_HWRST Deasserted after VDD_SUPPLIES (VDD_INT, VDD_EXT, VDD_DMC, VDD_USB, 11 × tCKIN
VDD_HADC, VDD_RTC, VDD_PCI_TX, VDD_PCI_RX, VDD_PCI_CORE) and SYS_CLKIN are Stable
and within Specification
SYS_HWRST
tRST_IN_PWR
SYS_CLKIN0/1
V
DD_SUPPLIES
NOTE: V
REFER TO V
,V
,V
,V
,V
,V
,V
,V
, AND V
.
DD_SUPPLIES
DD_INT DD_EXT DD_DMC DD_USB DD_HADC DD_RTC DD_PCI_TX DD_PCI_RX
DD_PCI_CORE
Figure 10. Power-Up Reset Timing
Rev. PrG |
Page 88 of 168 |
June 2016
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Clock and Reset Timing
Table 41 and Figure 11 describe clock and reset operations related to the clock generation unit (CGU) and reset control unit (RCU). Per
the CCLK, SYSCLK, SCLK, DCLK, and OCLK timing specifications in Table 29 in Clock Related Operating Conditions on Page 81, combinations of SYS_CLKIN and clock multipliers must not select clock rates in excess of the processor’s maximum instruction rate.
Table 41. Clock and Reset Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
SYS_CLKIN Frequency (Crystal)1, 2, 3
20
50
MHz
SYS_CLKIN Frequency (External CLKIN)1, 2, 3
20
50
MHz
Timing Requirements
fCKIN
1
tCKINL
CLKIN Low Pulse
tCKINH
CLKIN High Pulse1
tWRST
RESET Asserted Pulse Width Low
4
10
ns
10
ns
11 × tCKIN
ns
1
Applies to PLL bypass mode and PLL non bypass mode.
The tCKIN period (see Figure 11) equals 1/fCKIN.
3
If the CGU_CTL.DF bit is set, the minimum fCKIN specification is 40 MHz.
4
Applies after power-up sequence is complete. See Table 40 and Figure 10 for power-up reset timing.
2
fCKIN
SYS_CLKIN0/1
tCKINL
tCKINH
tWRST
SYS_HWRST
Figure 11. Clock and Reset Timing
Rev. PrG |
Page 89 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Asynchronous Read
Table 42 and Figure 12 show asynchronous memory read timing, related to the static memory controller (SMC).
Table 42. Asynchronous Memory Read
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSDATARE
DATA in Setup Before SMC0_ARE High
5.1
tHDATARE
DATA in Hold After SMC0_ARE High
0.7
tDARDYARE
SMC0_ARDY Valid After SMC0_ARE Low1, 2
ns
ns
(RAT – 2.5) × tSCLK0 – 17.5
ns
Switching Characteristics
tAMSARE
ADDR/SMC0_AMSx Assertion Before SMC0_ARE (PREST + RST + PREAT) × tSCLK0 – 2
Low3
ns
tAOEARE
SMC0_AOE Assertion Before SMC0_ARE Low
(RST + PREAT) × tSCLK0 – 2
ns
tHARE
Output4 Hold After SMC0_ARE High5
RHT × tSCLK0 –2
ns
RAT × tSCLK0 – 2
ns
6
tWARE
SMC0_ARE Active Low Width
tDAREARDY
SMC0_ARE High Delay After SMC0_ARDY
Assertion1
2.5 × tSCLK0
3.5 × tSCLK0 + 17.5
1
SMC0_BxCTL.ARDYEN bit = 1.
RAT value set using the SMC_BxTIM.RAT bits.
3
PREST, RST, and PREAT values set using the SMC_BxETIM.PREST bits, SMC_BxTIM.RST bits, and the SMC_BxETIM.PREAT bits.
4
Output signals are SMC0_Ax, SMC0_AMS, SMC0_AOE, SMC0_ABEx.
5
RHT value set using the SMC_BxTIM.RHT bits.
6
SMC0_BxCTL.ARDYEN bit = 0.
2
SMC0_ARE
SMC0_AMSx
tWARE
tHARE
tAMSARE
SMC0_Ax
tAOEARE
SMC0_AOE
tDARDYARE
tDAREARDY
SMC0_ARDY
tSDATARE
SMC0_Dx (DATA)
Figure 12. Asynchronous Read
Rev. PrG |
Page 90 of 168 |
June 2016
tHDATARE
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Asynchronous Flash Read
Table 43 and Figure 13 show asynchronous flash memory read timing, related to the static memory controller (SMC).
Table 43. Asynchronous Flash Read
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristics
tAMSADV
SMC0_Ax (Address)/SMC0_AMSx Assertion Before SMC0_NORDV
Low1
PREST × tSCLK0 – 2
tWADV
SMC0_NORDV Active Low Width2
RST × tSCLK0 – 2
ns
tDADVARE
SMC0_ARE Low Delay From SMC0_NORDV High3
PREAT × tSCLK0 – 2
ns
tHARE
Output4 Hold After SMC0_ARE High5
RHT × tSCLK0 – 2
ns
SMC0_ARE Active Low Width7
RAT × tSCLK0 – 2
ns
6
tWARE
1
PREST value set using the SMC_BxETIM.PREST bits.
RST value set using the SMC_BxTIM.RST bits.
3
PREAT value set using the SMC_BxETIM.PREAT bits.
4
Output signals are SMC0_Ax, SMC0_AMS, SMC0_AOE.
5
RHT value set using the SMC_BxTIM.RHT bits.
6
SMC0_BxCTL.ARDYEN bit = 0.
7
RAT value set using the SMC_BxTIM.RAT bits.
2
SMC0_Ax
(NOR_Ax)
SMC0_AMSx
(NOR_CE)
tAMSADV
tWADV
SMC0_AOE
(NOR_ADV)
tDADVARE
tWARE
tHARE
SMC0_ARE
(NOR_OE)
SMC0_Dx
(NOR_Dx)
READ LATCHED
DATA
Figure 13. Asynchronous Flash Read
Rev. PrG |
Page 91 of 168 |
June 2016
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Asynchronous Page Mode Read
Table 44 and Figure 14 show asynchronous memory page mode read timing, related to the static memory controller (SMC).
Table 44. Asynchronous Page Mode Read
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristics
tAV
SMC0_Ax (Address) Valid for First Address Min Width1
(PREST + RST + PREAT + RAT) × tSCLK0 – 2
ns
tAV1
SMC0_Ax (Address) Valid for Subsequent SMC0_Ax
(Address) Min Width
PGWS × tSCLK0 – 2
ns
tWADV
SMC0_NORDV Active Low Width2
RST × tSCLK0 – 2
ns
3
tHARE
Output Hold After SMC0_ARE High
tWARE5
SMC0_ARE Active Low Width6, 7
4
RHT × tSCLK0 – 2
ns
(RAT + (Nw – 1) × PGWS) × tSCLK0 – 2
ns
1
PREST, RST, PREAT and RAT values set using the SMC_BxETIM.PREST bits, SMC_BxTIM.RST bits, SMC_BxETIM.PREAT bits, and the SMC_BxTIM.RAT bits.
RST value set using the SMC_BxTIM.RST bits.
3
Output signals are SMC0_Ax, SMC0_AMSx, SMC0_AOE.
4
RHT value set using the SMC_BxTIM.RHT bits.
5
SMC_BxCTL.ARDYEN bit = 0.
6
RAT value set using the SMC_BxTIM.RAT bits.
7
Nw = Number of 16-bit data words read.
2
READ
LATCHED
DATA
SMC0_Ax
(NOR_Ax)
READ
LATCHED
DATA
READ
LATCHED
DATA
READ
LATCHED
DATA
tAV
tAV1
tAV1
tAV1
A0
A0 + 1
A0 + 2
A0 + 3
SMC0_AMSx
(NOR_CE)
SMC0_AOE
NOR_ADV
tWADV
tWARE
SMC0_ARE
(NOR_OE)
tHARE
SMC0_Dx
(NOR_Dx)
D0
D1
Figure 14. Asynchronous Page Mode Read
Rev. PrG |
Page 92 of 168 |
June 2016
D2
D3
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Asynchronous Write
Table 45 and Figure 15 show asynchronous memory write timing, related to the static memory controller (SMC).
Table 45. Asynchronous Memory Write
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
(WAT – 2.5) × tSCLK0 – 17.5
ns
Timing Requirement
tDARDYAWE1
SMC0_ARDY Valid After SMC0_AWE Low 2
Switching Characteristics
tENDAT
DATA Enable After SMC0_AMSx Assertion
–3.5
tDDAT
DATA Disable After SMC0_AMSx Deassertion
ns
2.5
3
ns
tAMSAWE
ADDR/SMC0_AMSx Assertion Before SMC0_AWE Low (PREST + WST + PREAT) × tSCLK0 – 2
ns
tHAWE
Output4 Hold After SMC0_AWE High5
ns
tWAWE
6
SMC0_AWE Active Low Width
tDAWEARDY1
WHT × tSCLK0 – 3.5
2
WAT × tSCLK0 – 2
SMC0_AWE High Delay After SMC0_ARDY Assertion
ns
2.5 × tSCLK0
3.5 × tSCLK0 + 17.5
1
SMC_BxCTL.ARDYEN bit = 1.
WAT value set using the SMC_BxTIM.WAT bits.
3
PREST, WST, PREAT values set using the SMC_BxETIM.PREST bits, SMC_BxTIM.WST bits, SMC_BxETIM.PREAT bits, and the SMC_BxTIM.RAT bits.
4
Output signals are DATA, SMC0_Ax, SMC0_AMSx, SMC0_ABEx.
5
WHT value set using the SMC_BxTIM.WHT bits.
6
SMC_BxCTL.ARDYEN bit = 0.
2
SMC0_AWE
SMC0_ABEx
SMC0_Ax
(ADDRESS)
tAMSAWE
tWAWE
tHAWE
SMC0_ARDY
tDARDYAWE
tDAWEARDY
SMC0_AMSx
SMC0_Dx (DATA)
tDDAT
tENDAT
Figure 15. Asynchronous Write
Rev. PrG |
Page 93 of 168 |
June 2016
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Asynchronous Flash Write
Table 46 and Figure 16 show asynchronous flash memory write timing, related to the static memory controller (SMC).
Table 46. Asynchronous Flash Write
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristics
tAMSADV
SMC0_Ax/SMC0_AMSx Assertion Before ADV Low1
tDADVAWE
SMC0_AWE Low Delay From ADV High
tWADV
NR_ADV Active Low Width3
tHAWE
Output4 Hold After SMC0_AWE High5
tWAWE
6
SMC0_AWE Active Low Width
PREST × tSCLK0 – 2
2
7
ns
PREAT × tSCLK0 – 2
ns
WST × tSCLK0 – 2
ns
WHT × tSCLK0 – 3.5
ns
WAT × tSCLK0 – 2
ns
1
PREST value set using the SMC_BxETIM.PREST bits.
2
PREAT value set using the SMC_BxETIM.PREAT bits.
3
WST value set using the SMC_BxTIM.WST bits.
4
Output signals are DATA, SMC0_Ax, SMC0_AMSx, SMC0_ABEx.
5
WHT value set using the SMC_BxTIM.WHT bits.
6
SMC_BxCTL.ARDYEN bit = 0.
7
WAT value set using the SMC_BxTIM.WAT bits.
NOR_A 25-1
(SMC0_Ax)
NOR_CE
(SMC0_AMSx)
tAMSADV
tWADV
NOR_ADV
(SMC0_AOE)
tWAWE
tDADVAWE
tHAWE
NOR_WE
(SMC0_AWE)
NOR_DQ 15-0
(SMC0_Dx)
Figure 16. Asynchronous Flash Write
All Accesses
Table 47 describes timing that applies to all memory accesses, related to the static memory controller (SMC).
Table 47. All Accesses
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristic
tTURN
SMC0_AMSx Inactive Width
(IT + TT) × tSCLK0 – 2
Rev. PrG |
Page 94 of 168 |
June 2016
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
DDR2 SDRAM Clock and Control Cycle Timing
Table 48 and Figure 17 show DDR2 SDRAM clock and control cycle timing, related to the dynamic memory controller (DMC).
Table 48. DDR2 SDRAM Clock and Control Cycle Timing, VDD_DMCx Nominal 1.8 V1
All specifications are based on simulation data and are subject to change without notice.
400 MHz2
Parameter
Min
Max
Unit
Switching Characteristics
1
2
tCK
Clock Cycle Time (CL = 2 Not Supported)
2.5
tCH
Minimum Clock Pulse Width
0.48
0.52
ns
tCK
tCL
Maximum Clock Pulse Width
0.48
0.52
tCK
tIS
Control/Address Setup Relative to DMCx_CK Rise
175
ps
tIH
Control/Address Hold Relative to DMCx_CK Rise
250
ps
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of the DDR2, all the DDR2 guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
tCK
tCH
tCL
DMCx_CK
DMCx_CK
tIS
tIH
DMCx_Ax
DMCx CONTROL
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A0-A15, AND DMCx_BA0-BA2.
Figure 17. DDR2 SDRAM Clock and Control Cycle Timing
Rev. PrG |
Page 95 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
DDR2 SDRAM Read Cycle Timing
Table 49 and Figure 18 show DDR2 SDRAM read cycle timing, related to the dynamic memory controller (DMC).
Table 49. DDR2 SDRAM Read Cycle Timing, VDD_DMCx Nominal 1.8 V1
All specifications are based on simulation data and are subject to change without notice.
400 MHz2
Parameter
Min
Max
Unit
0.2
ns
Timing Requirements
1
2
tDQSQ
DMCx_DQS-DMCx_DQ Skew for DMCx_DQS and Associated DMCx_DQ
Signals
tQH
DMCx_DQ, DMCx_DQS Output Hold Time From DMCx_DQS
0.9
ns
tRPRE
Read Preamble
0.9
tCK
tRPST
Read Postamble
0.4
tCK
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of the DDR2, all the DDR2 guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
tCK
tCH
tCL
DMCx_CKx
DMCx_CKx
DMCx_Ax
DMCx CONTROL
tRPRE
DMCx_LDQS/DMCx_UDQS
DMCx_LDQS/DMCx_UDQS
tDQSQ
tDQSQ
tRPST
tQH
tQH
DMCx_DQx
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A00-13, AND DMCx_BA0-1.
Figure 18. DDR2 SDRAM Controller Input AC Timing
Rev. PrG |
Page 96 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
DDR2 SDRAM Write Cycle Timing
Table 50 and Figure 19 show DDR2 SDRAM write cycle timing, related to the dynamic memory controller (DMC).
Table 50. DDR2 SDRAM Write Cycle Timing, VDD_DMCx Nominal 1.8 V1
All specifications are based on simulation data and are subject to change without notice.
400 MHz2
Parameter
Min
Max
0.15
Unit
Switching Characteristics
tDQSS
DMCx_DQS Latching Rising Transitions to Associated Clock Edges3
–0.15
tDS
Last Data Valid to DMCx_DQS Delay
0.1
ns
tDH
DMCx_DQS to First Data Invalid Delay
0.15
ns
tCK
tDSS
DMCx_DQS Falling Edge to Clock Setup Time
0.2
tCK
tDSH
DMCx_DQS Falling Edge Hold Time From DMCx_CK
0.2
tCK
tDQSH
DMCx_DQS Input High Pulse Width
0.35
tCK
tDQSL
DMCx_DQS Input Low Pulse Width
0.35
tCK
tWPRE
Write Preamble
0.35
tCK
tWPST
Write Postamble
0.4
tCK
tIPW
Address and Control Output Pulse Width
0.6
tCK
tDIPW
DMCx_DQ and DMCx_DM Output Pulse Width
0.35
tCK
1
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of the DDR2, all the DDR2 guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
3
Write command to first DMCx_DQS delay = WL × tCK + tDQSS.
2
DMCx_CK
DMCx_CK
tIPW
DMCx_Ax
DMCx CONTROL
tDSH
tDSS
tDQSS
DMCx_LDQS/DMCx_UDQS
DMCx_LDQS/DMCx_UDQS
DMC0_DQSn
DMC0_DQSn
tWPRE
tDQSL
tDS
tDH
tDQSH
tDIPW
DMCx_LDM
DMCx_UDM
DMCx_DQx
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A00-13, AND DMCx_BA0-1.
Figure 19. DDR2 SDRAM Controller Output AC Timing
Rev. PrG |
Page 97 of 168 |
June 2016
tWPST
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Mobile DDR (LPDDR) SDRAM Clock and Control Cycle Timing
Table 51 and Figure 20 show mobile DDR SDRAM clock and control cycle timing, related to the dynamic memory controller (DMC).
Table 51. Mobile DDR SDRAM Clock and Control Cycle Timing, VDD_DMCx Nominal 1.8 V1
All specifications are based on simulation data and are subject to change without notice.
200 MHz2
Parameter
Min
Max
Unit
Switching Characteristics
1
2
tCK
Clock Cycle Time (CL = 2 Not Supported)
5
tCH
Minimum Clock Pulse Width
0.45
0.55
ns
tCK
tCL
Maximum Clock Pulse Width
0.45
0.55
tCK
tIS
Control/Address Setup Relative to DMCx_CK Rise
1
ns
tIH
Control/Address Hold Relative to DMCx_CK Rise
1
ns
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of LPDDR, all the LPDDR guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
tCK
tCH
tCL
DMCx_CK
DMCx_CK
tIS
tIH
DMCx_Ax
DMCx CONTROL
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A0-A15, AND DMCx_BA0-BA2.
Figure 20. Mobile DDR SDRAM Clock and Control Cycle Timing
Rev. PrG |
Page 98 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Mobile DDR SDRAM Read Cycle Timing
Table 52 and Figure 21 show mobile DDR SDRAM read cycle timing, related to the dynamic memory controller (DMC).
Table 52. Mobile DDR SDRAM Read Cycle Timing, VDD_DMCx Nominal 1.8 V1
All specifications are based on simulation data and are subject to change without notice.
200 MHz2
Parameter
Min
Max
Unit
0.4
ns
Timing Requirements
1
2
tQH
DMCx_DQ, DMCx_DQS Output Hold Time From DMCx_DQS
tDQSQ
DMCx_DQS-DMCx_DQ Skew for DMCx_DQS and Associated
DMCx_DQ Signals
1.75
ns
tRPRE
Read Preamble
0.9
1.1
tCK
tRPST
Read Postamble
0.4
0.6
tCK
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of LPDDR, all the LPDDR guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
DMCx_CK
tRPRE
tRPST
DMCx_LDQS/DMCx_HDQS
tQH
DMCx_DQx
(DATA)
Dn
Dn+1
Dn+2
tDQSQ
Figure 21. Mobile DDR SDRAM Controller Input AC Timing
Rev. PrG |
Page 99 of 168 |
June 2016
Dn+3
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Mobile DDR SDRAM Write Cycle Timing
Table 53 and Figure 22 show mobile DDR SDRAM write cycle timing, related to the dynamic memory controller (DMC).
Table 53. Mobile DDR SDRAM Write Cycle Timing, VDD_DMCx Nominal 1.8 V1
All specifications are based on simulation data and are subject to change without notice.
200 MHz2
Parameter
Min
Max
1.25
Unit
Switching Characteristics
tDQSS3
DMCx_DQS Latching Rising Transitions to Associated Clock Edges
0.75
tDS
Last Data Valid to DMCx_DQS Delay (Slew > 1 V/ns)
0.48
ns
tDH
DMCx_DQS to First Data Invalid Delay (Slew > 1 V/ns)
0.48
ns
tDSS
DMCx_DQS Falling Edge to Clock Setup Time
0.2
tCK
tDSH
DMCx_DQS Falling Edge Hold Time From DMCx_CK
0.2
tCK
tDQSH
DMCx_DQS Input High Pulse Width
0.4
tCK
tDQSL
DMCx_DQS Input Low Pulse Width
0.4
tCK
tWPRE
Write Preamble
0.25
tCK
tWPST
Write Postamble
0.4
tCK
tIPW
Address and Control Output Pulse Width
2.3
ns
tDIPW
DMCx_DQ and DMCx_DM Output Pulse Width
1.8
ns
1
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of LPDDR, all the LPDDR guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
3
Write command to first DMCx_DQS delay = WL × tCK + tDQSS.
2
DMCx_CK
tDSS
tDSH
tDQSS
DMCx_LDQS/DMCx_HDQS
tWPRE
tDS
tDQSL
tDH
tDQSH
tWPST
tDIPW
DMCx_DQ0-15/
DMCx_LDQM/DMCx_HDQM
Dn
Dn+1
Dn+2
Dn+3
tDIPW
DMCx CONTROL
Write CMD
NOTE: CONTROL = DMCx_CSx, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A00-13, AND DMCx_BA0-1.
tIPW
Figure 22. Mobile DDR SDRAM Controller Output AC Timing
Rev. PrG
|
Page 100 of 168 |
June 2016
tCK
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
DDR3 SDRAM Clock and Control Cycle Timing
Table 54 and Figure 23 show mobile DDR3 SDRAM clock and control cycle timing, related to the dynamic memory controller (DMC).
Table 54. DDR3 SDRAM Clock and Control Cycle Timing VDD_DMCx Nominal 1.5 V1
All specifications are based on simulation data and are subject to change without notice.
450 MHz2
Parameter
Min
Max
Unit
Timing Requirements
1
2
tCK
Clock Cycle Time (CL = 2 Not Supported)
2.22
tCH
Minimum Clock Pulse Width
0.47
0.53
ns
tCK
tCL
Maximum Clock Pulse Width
0.47
0.53
tCK
tIS
Control/Address Setup Relative to DMCx_CK Rise
0.2
ns
tIH
Control/Address Hold Relative to DMCx_CK Rise
0.275
ns
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of the DDR3, all the DDR3 guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
tCK
tCH
tCL
DMCx_CK
DMCx_CK
tIS
tIH
DMCx_Ax
DMCx CONTROL
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A0-A15, AND DMCx_BA0-BA2.
Figure 23. DDR3 SDRAM Clock and Control Cycle Timing
Rev. PrG
|
Page 101 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
DDR3 SDRAM Read Cycle Timing
Table 55 and Figure 24 show mobile DDR3 SDRAM read cycle timing, related to the dynamic memory controller (DMC).
Table 55. DDR3 SDRAM Read Cycle Timing VDD_DMCx Nominal 1.5 V1
All specifications are based on simulation data and are subject to change without notice.
450 MHz2
Parameter
Min
Max
Unit
0.2
ns
Timing Requirements
1
2
tDQSQ
DMCx_DQS-DMCx_DQ Skew for DMCx_DQS and Associated DMCx_DQ
Signals
tQH
DMCx_DQ, DMCx_DQS Output Hold Time From DMCx_DQS
0.38
tCK
tRPRE
Read Preamble
0.9
tCK
tRPST
Read Postamble
0.3
tCK
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of the DDR3, all the DDR3 guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
tCK
tCH
tCL
DMCx_CKx
DMCx_CKx
DMCx_Ax
DMCx CONTROL
tRPRE
DMCx_LDQS/DMCx_UDQS
DMCx_LDQS/DMCx_UDQS
tDQSQ
tDQSQ
tRPST
tQH
tQH
DMCx_DQx
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A00-13, AND DMCx_BA0-1.
Figure 24. DDR3 SDRAM Controller Input AC Timing
Rev. PrG
|
Page 102 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
DDR3 SDRAM Write Cycle Timing
Table 56 and Figure 25 show mobile DDR3 SDRAM output ac timing, related to the dynamic memory controller (DMC).
Table 56. DDR3 SDRAM Write Cycle Timing VDD_DMCx Nominal 1.5 V1
All specifications are based on simulation data and are subject to change without notice.
450 MHz2
Parameter
Min
Max
0.25
Unit
Switching Characteristics
tDQSS
DMCx_DQS Latching Rising Transitions to Associated Clock Edges3
–0.25
tDS
Last Data Valid to DMCx_DQS Delay (Slew > 1 V/ns)
0.125
ns
tDH
DMCx_DQS to First Data Invalid Delay (Slew > 1 V/ns)
0.150
ns
tDSS
DMCx_DQS Falling Edge to Clock Setup Time
0.2
tCK
tDSH
DMCx_DQS Falling Edge Hold Time From DMCx_CK
0.2
tCK
tDQSH
DMCx_DQS Input High Pulse Width
0.45
0.55
tCK
tDQSL
DMCx_DQS Input Low Pulse Width
0.45
0.55
tCK
tWPRE
Write Preamble
0.9
tCK
tWPST
Write Postamble
0.3
tCK
tIPW
Address and Control Output Pulse Width
0.840
ns
tDIPW
DMCx_DQ and DMCx_DM Output Pulse Width
0.550
ns
tCK
1
Specifications apply to both DMC0 and DMC1.
In order to ensure proper operation of the DDR3, all the DDR3 guidelines must be strictly followed (see Engineer-to-Engineer Note EE-TBD).
3
Write command to first DMCx_DQS delay = WL × tCK + tDQSS.
2
DMCx_CK
DMCx_CK
tIPW
DMCx_Ax
DMCx CONTROL
tDSH
tDSS
tDQSS
DMCx_LDQS/DMCx_UDQS
DMCx_LDQS/DMCx_UDQS
DMC0_DQSn
DMC0_DQSn
tDQSL
tWPRE
tDS
tDIPW
tDH
DMCx_LDM
DMCx_UDM
DMCx_DQx
NOTE: CONTROL = DMCx_CS0, DMCx_CKE, DMCx_RAS, DMCx_CAS, AND DMCx_WE.
ADDRESS = DMCx_A00-13, AND DMCx_BA0-1.
Figure 25. DDR3 SDRAM Controller Output AC Timing
Rev. PrG
|
Page 103 of 168 |
tDQSH
June 2016
tWPST
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Enhanced Parallel Peripheral Interface Timing
The following tables and figures describe enhanced parallel peripheral interface (EPPI) timing operations. The POLC bits in the
EPPI_CTL register may be used to set the sampling/driving edges of the EPPI clock.
When internally generated, the programmed PPI clock (fPCLKPROG) frequency in MHz is set by the following equation where VALUE is a
field in the EPPI_CLKDIV register that can be set from 0 to 65535:
f SCLK0
f PCLKPROG = -------------------------- VALUE + 1 
1
t PCLKPROG = ----------------f PCLKPROG
When externally generated the EPPI_CLK is called fPCLKEXT:
1
t PCLKEXT = ------------f PCLKEXT
Table 57. Enhanced Parallel Peripheral Interface—Internal Clock
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSFSPI
External FS Setup Before EPPI_CLK
6.5
ns
tHFSPI
External FS Hold After EPPI_CLK
0
ns
tSDRPI
Receive Data Setup Before EPPI_CLK
6.5
ns
tHDRPI
Receive Data Hold After EPPI_CLK
0
ns
tSFS3GI
External FS3 Input Setup Before EPPI_CLK Fall Edge in Clock
Gating Mode
14
ns
tHFS3GI
External FS3 Input Hold Before EPPI_CLK Fall Edge in Clock
Gating Mode
0
ns
Switching Characteristics
1
tPCLKW
EPPI_CLK Width1
0.5 × tPCLKPROG – 1.5
ns
tPCLK
EPPI_CLK Period1
tPCLKPROG – 1.5
ns
tDFSPI
Internal FS Delay After EPPI_CLK
tHOFSPI
Internal FS Hold After EPPI_CLK
tDDTPI
Transmit Data Delay After EPPI_CLK
tHDTPI
Transmit Data Hold After EPPI_CLK
3.5
ns
3.5
ns
–0.5
ns
–0.5
See Table 29 in Clock Related Operating Conditions on Page 81 for details on the minimum period that may be programmed for tPCLKPROG.
Rev. PrG
|
Page 104 of 168 |
June 2016
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
FRAME SYNC
DRIVEN
DATA
SAMPLED
POLC[1:0] = 10
EPPI_CLK
POLC[1:0] = 01
tDFSPI
tPCLKW
tHOFSPI
tPCLK
EPPI_FS1/2
tSDRPI
tHDRPI
EPPI_D00-23
Figure 26. PPI Internal Clock GP Receive Mode with Internal Frame Sync Timing
FRAME SYNC
DRIVEN
DATA
DRIVEN
DATA
DRIVEN
tPCLK
POLC[1:0] = 11
EPPI_CLK
POLC[1:0] = 00
tDFSPI
tPCLKW
tHOFSPI
EPPI_FS1/2
tHDTPI
tDDTPI
EPPI_D00-23
Figure 27. PPI Internal Clock GP Transmit Mode with Internal Frame Sync Timing
DATA SAMPLED /
FRAME SYNC SAMPLED
DATA SAMPLED /
FRAME SYNC SAMPLED
POLC[1:0] = 11
EPPI_CLK
POLC[1:0] = 00
tSFSPI
tPCLKW
tHFSPI
tPCLK
PPI_FS1/2
tSDRPI
tHDRPI
PPI_D00-23
Figure 28. PPI Internal Clock GP Receive Mode with External Frame Sync Timing
Rev. PrG
|
Page 105 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
DATA DRIVEN /
FRAME SYNC SAMPLED
POLC[1:0] = 11
PPI_CLK
POLC[1:0] = 00
tSFSPI
tHFSPI
tPCLKW
tPCLK
PPI_FS1/2
tDDTPI
tHDTPI
PPI_D00-23
Figure 29. PPI Internal Clock GP Transmit Mode with External Frame Sync Timing
EPPI_CLK
tHFS3GI
tSFS3GI
EPPI_FS3
Figure 30. Clock Gating Mode with Internal Clock and External Frame Sync Timing
Table 58. Enhanced Parallel Peripheral Interface—External Clock
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tPCLKW
EPPI_CLK Width1
1
0.5 × tPCLKEXT – 0.5
ns
tPCLK
EPPI_CLK Period
tPCLKEXT – 1
ns
tSFSPE
External FS Setup Before EPPI_CLK
2
ns
tHFSPE
External FS Hold After EPPI_CLK
3.7
ns
tSDRPE
Receive Data Setup Before EPPI_CLK
2
ns
tHDRPE
Receive Data Hold After EPPI_CLK
3.7
ns
Switching Characteristics
1
tDFSPE
Internal FS Delay After EPPI_CLK
tHOFSPE
Internal FS Hold After EPPI_CLK
tDDTPE
Transmit Data Delay After EPPI_CLK
tHDTPE
Transmit Data Hold After EPPI_CLK
15.3
2.4
ns
ns
15.3
2.4
ns
ns
This specification indicates the minimum instantaneous width or period that can be tolerated due to duty cycle variation or jitter on the external EPPI_CLK. For the external
EPPI_CLK ideal maximum frequency see the fPCLKEXT specification in Table 29 in Clock Related Operating Conditions on Page 81.
Rev. PrG
|
Page 106 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
FRAME SYNC
DRIVEN
DATA
SAMPLED
POLC[1:0] = 10
EPPI_CLK
POLC[1:0] = 01
tDFSPE
tPCLKW
tHOFSPE
tPCLK
EPPI_FS1/2
tSDRPE
tHDRPE
EPPI_D00-23
Figure 31. PPI External Clock GP Receive Mode with Internal Frame Sync Timing
FRAME SYNC
DRIVEN
DATA
DRIVEN
DATA
DRIVEN
tPCLK
POLC[1:0] = 11
EPPI_CLK
POLC[1:0] = 00
tDFSPE
tPCLKW
tHOFSPE
EPPI_FS1/2
tDDTPE
tHDTPE
EPPI_D00-23
Figure 32. PPI External Clock GP Transmit Mode with Internal Frame Sync Timing
DATA SAMPLED /
FRAME SYNC SAMPLED
DATA SAMPLED /
FRAME SYNC SAMPLED
POLC[1:0] = 11
EPPI_CLK
POLC[1:0] = 00
tSFSPE
tPCLKW
tHFSPE
tPCLK
EPPI_FS1/2
tSDRPE
tHDRPE
EPPI_D00-23
Figure 33. PPI External Clock GP Receive Mode with External Frame Sync Timing
Rev. PrG
|
Page 107 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
DATA DRIVEN /
FRAME SYNC SAMPLED
POLC[1:0] = 11
EPPI_CLK
POLC[1:0] = 00
tSFSPE
tHFSPE
tPCLKW
tPCLK
EPPI_FS1/2
tDDTPE
tHDTPE
EPPI_D00-23
Figure 34. PPI External Clock GP Transmit Mode with External Frame Sync Timing
Rev. PrG
|
Page 108 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Link Ports
In link port (LP) receive mode, the link port clock is supplied externally and is called fLCLKREXT:
1
t LCLKREXT = --------------f LCLKREXT
In link port transmit mode, the programmed link port clock (fLCLKTPROG) frequency in MHz is set by the following equation where
VALUE is a field in the LP_DIV register that can be set from 1 to 255:
f CLKO8
f LCLKTPROG = -------------------------- VALUE  2 
In the case where VALUE = 0, fLCLKTPROG = fCLKO8. For all settings of VALUE the following equation also holds:
1
t LCLKTPROG = -----------------f LCLKTPROG
Calculation of link receiver data setup and hold relative to link clock is required to determine the maximum allowable skew that can be
introduced in the transmission path length difference between LPx_Dx (data) and LPx_CLK. Setup skew is the maximum delay that can
be introduced in LPx_Dx relative to LPx_CLK: (setup skew = tLCLKTWH min – tDLDCH – tSLDCL). Hold skew is the maximum delay that can
be introduced in LPx_CLK relative to LPx_Dx: (hold skew = tLCLKTWL min – tHLDCH – tHLDCL).
Table 59. Link Ports—Receive1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
150
MHz
Timing Requirements
fLCLKREXT
LPx_CLK Frequency
tSLDCL
Data Setup Before LPx_CLK Low
0.9
ns
tHLDCL
Data Hold After LPx_CLK Low
1.4
ns
2
tLCLKEW
LPx_CLK Period
tLCLKREXT – 0.42
ns
tLCLKRWL
LPx_CLK Width Low2
0.5 × tLCLKREXT
ns
tLCLKRWH
LPx_CLK Width High2
0.5 × tLCLKREXT
ns
Switching Characteristic
tDLALC
LPx_ACK Low Delay After LPx_CLK Low3
1.5 × tCLKO8 + 4
1
2.5 × tCLKO8 + 12
ns
Specifications apply to LP1 and LP2.
This specification indicates the minimum instantaneous width or period that can be tolerated due to duty cycle variation or jitter on the external LPx_CLK. For the external
LPx_CLK ideal maximum frequency see the fLCLKTEXT specification in Table 29 in Clock Related Operating Conditions on Page 81.
3
LPx_ACK goes low with tDLALC relative to rise of LPx_CLK after first byte, but does not go low if the receiver's link buffer is not about to fill.
2
Rev. PrG
|
Page 109 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
tLCLKEW
tLCLKRWH
tLCLKRWL
LPx_CLK
tHLDCL
tSLDCL
LPx_D7–0
IN
tDLALC
LPx_ACK (OUT)
Figure 35. Link Ports—Receive
Rev. PrG
|
Page 110 of 168 |
June 2016
Preliminary Technical Data
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 60. Link Ports—Transmit1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSLACH
LPx_ACK Setup Before LPx_CLK Low
2 × tCLKO8 + 13.5
ns
tHLACH
LPx_ACK Hold After LPx_CLK Low
–5.5
ns
Switching Characteristics
tDLDCH
Data Delay After LPx_CLK High
tHLDCH
Data Hold After LPx_CLK High
–0.8
LPx_CLK Width Low
0.33 × tLCLKTPROG
0.6 × tLCLKTPROG
ns
LPx_CLK Width High
0.45 × tLCLKTPROG
0.66 × tLCLKTPROG
ns
LPx_CLK Period
N × tLCLKTPROG – 0.5
LPx_CLK Low Delay After LPx_ACK High
tCLKO8 + 4
tLCLKTWL
2
tLCLKTWH2
tLCLKTW
tDLACLK
1
2
2
1.6
ns
ns
ns
2 × tCLKO8 + 1 × tLPCLK + 10
Specifications apply to LP1 and LP2
See Table 29 in Clock Related Operating Conditions on Page 81 for details on the minimum period that may be programmed for tLCLKTPROG.
tLCLKTWH
LAST BYTE
TRANSMITTED
tLCLKTWL
FIRST BYTE
TRANSMITTED1
LPx_CLK
tDLDCH
tHLDCH
LPx_Dx
(DATA)
OUT
tSLACH
tHLACH
tDLACLK
LPx_ACK (IN)
NOTES
The tSLACH and tHLACH specifications apply only to the LPx_CLK falling edge. If these specifications are met,
LPx_CLK would extend and the dotted LPx_CLK falling edge would not occur as shown. The position of the
dotted falling edge can be calculated using the tLCLKTWH specification. tLCLKTWH Min should be used for tSLACH
and tLCLKTWH Max for tHLACH.
Figure 36. Link Ports—Transmit
Rev. PrG
|
Page 111 of 168 |
June 2016
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Serial Ports
To determine whether serial port (SPORT) communication is possible between two devices at clock speed n, the following specifications
must be confirmed: 1) frame sync delay and frame sync setup and hold, 2) data delay and data setup and hold, and 3) serial clock
(SPTx_CLK) width. In Figure 37 either the rising edge or the falling edge of SPTx_CLK (external or internal) can be used as the active
sampling edge.
When externally generated, the SPORT clock is called fSPTCLKEXT:
1
t SPTCLKEXT = ----------------------f SPTCLKEXT
When internally generated, the programmed SPORT clock (fSPTCLKPROG) frequency in MHz is set by the following equation where
CLKDIV is a field in the SPORT_DIV register that can be set from 0 to 65535:
f SCLK0
f SPTCLKPROG = ------------------------------
 CLKDIV + 1 
1
t SPTCLKPROG = -------------------------f SPTCLKPROG
Table 61. Serial Ports—External Clock1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSFSE
Frame Sync Setup Before SPTx_CLK
2
(Externally Generated Frame Sync in either Transmit or Receive
Mode)2
ns
tHFSE
Frame Sync Hold After SPTx_CLK
2.7
(Externally Generated Frame Sync in either Transmit or Receive
Mode)2
ns
tSDRE
Receive Data Setup Before Receive SPTx_CLK2
2
ns
tHDRE
Receive Data Hold After SPTx_CLK2
2.7
ns
tSPTCLKW
SPTx_CLK Width3
0.5 × tSPTCLKEXT – 1.5
ns
tSPTCLK
SPTx_CLK Period3
tSPTCLKEXT – 1.5
ns
Switching Characteristics
tDFSE
Frame Sync Delay After SPTx_CLK
(Internally Generated Frame Sync in either Transmit or Receive
Mode)4
14.5
tHOFSE
Frame Sync Hold After SPTx_CLK
2
(Internally Generated Frame Sync in either Transmit or Receive
Mode)4
tDDTE
Transmit Data Delay After Transmit SPTx_CLK4
tHDTE
Transmit Data Hold After Transmit SPTx_CLK4
ns
14
2
1
ns
ns
ns
Specifications apply to all eight SPORTs.
Referenced to sample edge.
3
This specification indicates the minimum instantaneous width or period that can be tolerated due to duty cycle variation or jitter on the external SPTx_CLK. For the external
SPTx_CLK ideal maximum frequency see the fSPTCLKEXT specification in Table 29 in Clock Related Operating Conditions on Page 81.
4
Referenced to drive edge.
2
Rev. PrG
|
Page 112 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 62. Serial Ports—Internal Clock1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSFSI
tHFSI
tSDRI
tHDRI
Frame Sync Setup Before SPTx_CLK
(Externally Generated Frame Sync in either Transmit or
Receive Mode)2
12
Frame Sync Hold After SPTx_CLK
(Externally Generated Frame Sync in either Transmit or
Receive Mode)2
–0.5
Receive Data Setup Before SPTx_CLK2
3.4
ns
1.5
ns
Receive Data Hold After SPTx_CLK
2
ns
ns
Switching Characteristics
tDFSI
Frame Sync Delay After SPTx_CLK (Internally Generated
Frame Sync in Transmit or Receive Mode)3
tHOFSI
Frame Sync Hold After SPTx_CLK (Internally Generated
Frame Sync in Transmit or Receive Mode)3
tDDTI
Transmit Data Delay After SPTx_CLK3
tHDTI
Transmit Data Hold After SPTx_CLK
tSCLKIW
SPTx_CLK Width4
tSPTCLK
4
SPTx_CLK Period
3.5
–2.5
ns
3.5
3
ns
0.5 × tSPTCLKPROG – 1.5
ns
tSPTCLKPROG – 1.5
ns
Specifications apply to all eight SPORTs.
Referenced to the sample edge.
3
Referenced to drive edge.
4
See Table 29 in Clock Related Operating Conditions on Page 81 for details on the minimum period that may be programmed for tSPTCLKPROG.
2
|
Page 113 of 168 |
ns
–2.5
1
Rev. PrG
ns
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
DATA RECEIVE—INTERNAL CLOCK
DRIVE EDGE
Preliminary Technical Data
DATA RECEIVE—EXTERNAL CLOCK
SAMPLE EDGE
DRIVE EDGE
tSCLKIW
SAMPLE EDGE
tSCLKW
SPTx_A/BCLK
(SPORT CLOCK)
SPTx_A/BCLK
(SPORT CLOCK)
tDFSI
tDFSE
tSFSI
tHOFSI
tHFSI
tSFSE
tHFSE
tSDRE
tHDRE
tHOFSE
SPTx_A/BFS
(FRAME SYNC)
SPTx_A/BFS
(FRAME SYNC)
tSDRI
tHDRI
SPTx_A/BDx
(DATA CHANNEL A/B)
SPTx_A/BDx
(DATA CHANNEL A/B)
DATA TRANSMIT—INTERNAL CLOCK
DRIVE EDGE
DATA TRANSMIT—EXTERNAL CLOCK
SAMPLE EDGE
DRIVE EDGE
tSCLKIW
SAMPLE EDGE
tSCLKW
SPTx_A/BCLK
(SPORT CLOCK)
SPTx_A/BCLK
(SPORT CLOCK)
tDFSI
tDFSE
tHOFSI
tSFSI
tHFSI
tSFSE
tHOFSE
SPTx_A/BFS
(FRAME SYNC)
SPTx_A/BFS
(FRAME SYNC)
tDDTI
tDDTE
tHDTI
tHDTE
SPTx_A/BDx
(DATA CHANNEL A/B)
SPTx_A/BDx
(DATA CHANNEL A/B)
Figure 37. Serial Ports
Rev. PrG
|
Page 114 of 168 |
June 2016
tHFSE
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 63. Serial Ports—Enable and Three-State1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
14
ns
Switching Characteristics
tDDTEN
Data Enable from External Transmit SPTx_CLK2
tDDTTE
Data Disable from External Transmit SPTx_CLK2
tDDTIN
Data Enable from Internal Transmit SPTx_CLK2
tDDTTI
Data Disable from Internal Transmit SPTx_CLK
1
ns
–2.5
ns
2
2.8
1
Specifications apply to all eight SPORTs.
2
Referenced to drive edge.
DRIVE EDGE
DRIVE EDGE
SPTx_CLK
(SPORT CLOCK EXTERNAL)
tDDTEN
tDDTTE
SPTx_A/BDx
(DATA CHANNEL A/B)
DRIVE EDGE
DRIVE EDGE
SPTx_CLK
(SPORT CLOCK INTERNAL)
tDDTIN
tDDTTI
SPTx_A/BDx
(DATA CHANNEL A/B)
Figure 38. Serial Ports—Enable and Three-State
Rev. PrG
|
Page 115 of 168 |
June 2016
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
The SPTx_TDV output signal becomes active in SPORT multichannel mode. During transmit slots (enabled with active channel selection
registers) the SPTx_TDV is asserted for communication with external devices.
Table 64. Serial Ports—TDV (Transmit Data Valid)1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristics
tDRDVEN
Data-Valid Enable Delay from Drive Edge of External Clock2
2
2
tDFDVEN
Data-Valid Disable Delay from Drive Edge of External Clock
tDRDVIN
Data-Valid Enable Delay from Drive Edge of Internal Clock2
tDFDVIN
Data-Valid Disable Delay from Drive Edge of Internal Clock2
14
–2.5
Specifications apply to all eight SPORTs.
2
Referenced to drive edge.
DRIVE EDGE
DRIVE EDGE
SPTx_CLK
(SPORT CLOCK EXTERNAL)
tDRDVEN
tDFDVEN
SPTx_A/BTDV
DRIVE EDGE
DRIVE EDGE
SPTx_CLK
(SPORT CLOCK INTERNAL)
tDRDVIN
tDFDVIN
SPTx_A/BTDV
Figure 39. Serial Ports—Transmit Data Valid Internal and External Clock
|
Page 116 of 168 |
June 2016
ns
ns
3.5
1
Rev. PrG
ns
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 65. Serial Ports—External Late Frame Sync1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
14
ns
Switching Characteristics
1
2
tDDTLFSE
Data Delay from Late External Transmit Frame Sync or External Receive Frame
Sync with MCE = 1, MFD = 02
tDDTENFS
Data Enable for MCE = 1, MFD = 02
0.5
ns
Specifications apply to all eight SPORTs.
The tDDTLFSE and tDDTENFS parameters apply to left-justified as well as standard serial mode, and MCE = 1, MFD = 0.
DRIVE
SAMPLE
DRIVE
SPTx_A/BCLK
(SPORT CLOCK)
tHFSE/I
tSFSE/I
SPTx_A/BFS
(FRAME SYNC)
tDDTE/I
tDDTENFS
tHDTE/I
SPTx_A/BDx
(DATA CHANNEL A/B)
1ST BIT
2ND BIT
tDDTLFSE
Figure 40. External Late Frame Sync
Rev. PrG
|
Page 117 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Sample Rate Converter—Serial Input Port
The ASRC input signals are routed from the DAIx_P20–1 pins using the SRU. Therefore, the timing specifications provided in Table 66
are valid at the DAIx_P20–1 pins.
Table 66. ASRC, Serial Input Port
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSRCSFS1
1
1
Frame Sync Setup Before Serial Clock Rising Edge
4
ns
tSRCHFS
Frame Sync Hold After Serial Clock Rising Edge
5.5
ns
tSRCSD1
Data Setup Before Serial Clock Rising Edge
4
ns
tSRCHD1
Data Hold After Serial Clock Rising Edge
5.5
ns
tSRCCLKW
Clock Width
tSCLK0 – 1
ns
tSRCCLK
Clock Period
2 × tSCLK0
ns
The serial clock, data, and frame sync signals can come from any of the DAI pins. The serial clock and frame sync signals can also come via PCG or SPORTs. PCG’s input
can be either CLKIN or any of the DAI pins.
SAMPLE EDGE
tSRCCLK
tSRCCLKW
DAIx_PIN20–1
(SCLK)
tSRCSFS
tSRCHFS
DAIx_PIN20–1
(FS)
tSRCSD
tSRCHD
DAIX_PIN20–1
(SDATA)
Figure 41. ASRC Serial Input Port Timing
Rev. PrG
|
Page 118 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Sample Rate Converter—Serial Output Port
For the serial output port, the frame sync is an input, and it should meet setup and hold times with regard to SCLK on the output port. The
serial data output has a hold time and delay specification with regard to serial clock. Note that serial clock rising edge is the sampling edge,
and the falling edge is the drive edge.
Table 67. ASRC, Serial Output Port
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSRCSFS1
Frame Sync Setup Before Serial Clock Rising Edge
4
ns
tSRCHFS1
Frame Sync Hold After Serial Clock Rising Edge
5.5
ns
tSRCCLKW
Clock Width
tSCLK0 – 1
ns
tSRCCLK
Clock Period
2 × tSCLK0
ns
Switching Characteristics
1
tSRCTDD1
Transmit Data Delay After Serial Clock Falling Edge
tSRCTDH1
Transmit Data Hold After Serial Clock Falling Edge
13
1
ns
ns
The serial clock, data, and frame sync signals can come from any of the DAI pins. The serial clock and frame sync signals can also come via PCG or SPORTs. PCG’s input
can be either CLKIN, SCLK0, or any of the DAI pins.
SAMPLE EDGE
tSRCCLK
tSRCCLKW
DAIx_PIN20–1
(SCLK)
tSRCSFS
tSRCHFS
DAIx_PIN20–1
(FS)
tSRCTDD
tSRCTDH
DAIx_PIN20–1
(SDATA)
Figure 42. ASRC Serial Output Port Timing
Rev. PrG
|
Page 119 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Serial Peripheral Interface (SPI) Port—Master Timing
Table 68 and Figure 43 describe serial peripheral interface (SPI) port master operations.
When internally generated, the programmed SPI clock (fSPICLKPROG) frequency in MHz is set by the following equation where BAUD is a
field in the SPIx_CLK register that can be set from 0 to 65535:
f SCLK1
f SPICLKPROG = ---------------------------
 BAUD + 1 
1
t SPICLKPROG = ------------------------f SPICLKPROG
Note that:
• In dual mode data transmit the SPIx_MISO signal is also an output.
• In quad mode data transmit the SPIx_MISO, SPIx_D2, and SPIx_D3 signals are also outputs.
• In dual mode data receive the SPIx_MOSI signal is also an input.
• In quad mode data receive the SPIx_MOSI, SPIx_D2, and SPIx_D3 signals are also inputs.
• Quad mode is supported by SPI2 only.
Table 68. Serial Peripheral Interface (SPI) Port—Master Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSSPIDM
Data Input Valid to SPIx_CLK Edge (Data Input Setup)
3.2
ns
tHSPIDM
SPIx_CLK Sampling Edge to Data Input Invalid
1.2
ns
[tSCLK1 – 2] or [18]
ns
Switching Characteristics
tSDSCIM
SPIx_SEL low to First SPI_CLK Edge for CPHA = 12
SPIx_SEL low to First SPI_CLK Edge for CPHA = 0
2
[1.5 × tSCLK1 – 2] or [13]
ns
tSPICHM
SPIx_CLK High Period3
0.5 × tSPICLKPROG – 1
ns
tSPICLM
SPIx_CLK Low Period3
0.5 × tSPICLKPROG – 1
ns
tSPICLK
SPIx_CLK Period3
tSPICLKPROG – 1
ns
[1.5 × tSCLK1 –2] or [13]
ns
[tSCLK1 –2] or [18]
ns
tHDSM
Last SPIx_CLK Edge to SPIx_SEL High for CPHA = 1
2
Last SPIx_CLK Edge to SPIx_SEL High for CPHA = 02
2, 4
tSPITDM
Sequential Transfer Delay
tDDSPIDM
SPIx_CLK Edge to Data Out Valid (Data Out Delay)
[tSCLK1 – 1] or [19]
tHDSPIDM
SPIx_CLK Edge to Data Out Invalid (Data Out Hold)
ns
2.6
–1.5
1
All specifications apply to all three SPIs.
Whichever is greater.
3
See Table 29 in Clock Related Operating Conditions on Page 81 for details on the minimum period that may be programmed for tSPICLKPROG.
4
Applies to sequential mode with STOP ≥ 1.
2
Rev. PrG
|
Page 120 of 168 |
June 2016
ns
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
SPIx_SEL
(OUTPUT)
tSDSCIM
tSPICLM
tSPICHM
tSPICLK
tHDSM
SPIx_CLK
(OUTPUT)
tHDSPIDM
tDDSPIDM
DATA OUTPUTS
(SPIx_MOSI)
tSSPIDM
CPHA = 1
tHSPIDM
DATA INPUTS
(SPIx_MISO)
tDDSPIDM
tHDSPIDM
DATA OUTPUTS
(SPIx_MOSI)
CPHA = 0
tSSPIDM
tHSPIDM
DATA INPUTS
(SPIx_MISO)
Figure 43. Serial Peripheral Interface (SPI) Port—Master Timing
Rev. PrG
|
Page 121 of 168 |
June 2016
tSPITDM
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Serial Peripheral Interface (SPI) Port—Slave Timing
Table 69 and Figure 44 describe serial peripheral interface (SPI) port slave operations. Note that:
• In dual mode data transmit the SPIx_MOSI signal is also an output.
• In quad mode data transmit the SPIx_MOSI, SPIx_D2, and SPIx_D3 signals are also outputs.
• In dual mode data receive the SPIx_MISO signal is also an input.
• In quad mode data receive the SPIx_MISO, SPIx_D2, and SPIx_D3 signals are also inputs.
• In SPI slave mode the SPI clock is supplied externally and is called fSPICLKEXT:
1
t SPICLKEXT = ---------------------f SPICLKEXT
• Quad mode is supported by SPI2 only.
Table 69. Serial Peripheral Interface (SPI) Port—Slave Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSPICHS
SPIx_CLK High Period2
0.5 × tSPICLKEXT – 1
ns
tSPICLS
SPIx_CLK Low Period2
0.5 × tSPICLKEXT – 1
ns
2
tSPICLK
SPIx_CLK Period
tSPICLKEXT – 1
ns
tHDS
Last SPIx_CLK Edge to SPIx_SS Not Asserted
5
ns
tSPITDS
Sequential Transfer Delay
tSPICLK – 1
ns
tSDSCI
SPIx_SS Assertion to First SPIx_CLK Edge
10.5
ns
tSSPID
Data Input Valid to SPIx_CLK Edge (Data Input Setup)
2
ns
tHSPID
SPIx_CLK Sampling Edge to Data Input Invalid
1.6
ns
Switching Characteristics
tDSOE
SPIx_SS Assertion to Data Out Active
0
14
ns
tDSDHI
SPIx_SS Deassertion to Data High Impedance
0
12.5
ns
tDDSPID
SPIx_CLK Edge to Data Out Valid (Data Out Delay)
14
ns
tHDSPID
SPIx_CLK Edge to Data Out Invalid (Data Out Hold)
0
ns
1
All specifications apply to all three SPIs.
2
This specification indicates the minimum instantaneous width or period that can be tolerated due to duty cycle variation or jitter on the external SPIx_CLK. For the external
SPIx_CLK ideal maximum frequency see the fSPICLKTEXT specification in Table 29 in Clock Related Operating Conditions on Page 81.
Rev. PrG
|
Page 122 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
SPIx_SS
(INPUT)
tSDSCI
tSPICLS
tSPICHS
tHDS
tSPICLK
SPIx_CLK
(INPUT)
tDSOE
tDDSPID
tDDSPID
tHDSPID
tDSDHI
DATA OUTPUTS
(SPIx_MISO)
CPHA = 1
tSSPID
tHSPID
DATA INPUTS
(SPIx_MOSI)
tDSOE
tHDSPID
tDDSPID
tDSDHI
DATA OUTPUTS
(SPIx_MISO)
tHSPID
CPHA = 0
tSSPID
DATA INPUTS
(SPIx_MOSI)
Figure 44. Serial Peripheral Interface (SPI) Port—Slave Timing
Rev. PrG
|
Page 123 of 168 |
June 2016
tSPITDS
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Serial Peripheral Interface (SPI) Port—SPIx_RDY Slave Timing
Table 70. SPI Port—SPIx_RDY Slave Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristics
1
tDSPISCKRDYSR
SPIx_RDY Deassertion from Valid Input SPIx_CLK Edge in Slave Mode Receive
3 × tSCLK1
4 × tSCLK1 + 10
ns
tDSPISCKRDYST
SPIx_RDY Deassertion from Valid Input SPIx_CLK Edge in Slave Mode Transmit
4 × tSCLK1
5 × tSCLK1 + 10
ns
All specifications apply to all three SPIs.
tDSPISCKRDYSR
SPIx_CLK
(CPOL = 0)
CPHA = 0
SPIx_CLK
(CPOL = 1)
SPIx_CLK
(CPOL = 0)
CPHA = 1
SPIx_CLK
(CPOL = 1)
SPIx_RDY (O)
Figure 45. SPIx_RDY Deassertion from Valid Input SPIx_CLK Edge in Slave Mode Receive (FCCH = 0)
tDSPISCKRDYST
SPIx_CLK
(CPOL = 1)
CPHA = 0
SPIx_CLK
(CPOL = 0)
SPIx_CLK
(CPOL = 1)
CPHA = 1
SPIx_CLK
(CPOL = 0)
SPIx_RDY (O)
Figure 46. SPIx_RDY Deassertion from Valid Input SPIx_CLK Edge in Slave Mode Transmit (FCCH = 1)
Rev. PrG
|
Page 124 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Serial Peripheral Interface (SPI) Port—Open Drain Mode Timing
In Figure 47 and Figure 48, the outputs can be SPIx_MOSI SPIx_MISO, SPIx_D2, and/or SPIx_D3 depending on the mode of operation.
Table 71. SPI Port ODM Master Mode Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Switching Characteristics
1
tHDSPIODMM
SPIx_CLK Edge to High Impedance from Data Out Valid
–1
tDDSPIODMM
SPIx_CLK Edge to Data Out Valid from High Impedance
–1
ns
6
ns
Max
Unit
All specifications apply to all three SPIs.
tHDSPIODMM
tHDSPIODMM
SPIx_CLK
(CPOL = 0)
SPIx_CLK
(CPOL = 1)
OUTPUT
(CPHA = 1)
OUTPUT
(CPHA = 0)
tDDSPIODMM
tDDSPIODMM
Figure 47. ODM Master
Table 72. SPI Port—ODM Slave Mode1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Timing Requirements
1
tHDSPIODMS
SPIx_CLK Edge to High Impedance from Data Out Valid
tDDSPIODMS
SPIx_CLK Edge to Data Out Valid from High Impedance
0
ns
11
All specifications apply to all three SPIs.
tHDSPIODMS
tHDSPIODMS
SPIx_CLK
(CPOL = 0)
SPIx_CLK
(CPOL = 1)
OUTPUT
(CPHA = 1)
OUTPUT
(CPHA = 0)
tDDSPIODMS
tDDSPIODMS
Figure 48. ODM Slave
Rev. PrG
|
Page 125 of 168 |
June 2016
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Serial Peripheral Interface (SPI) Port—SPIx_RDY Master Timing
SPIx_RDY is used to provide flow control. The CPOL and CPHA bits are set in SPIx_CTL, while LEADX, LAGX, and STOP are in
SPIx_DLY.
Table 73. SPI Port—SPIx_RDY Master Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSRDYSCKM0
Minimum Setup Time for SPIx_RDY Deassertion in Master
(2 + 2 × BAUD2) × tSCLK1 + 10
Mode Before Last Valid SPIx_CLK Edge of Valid Data Transfer to
Block Subsequent Transfer with CPHA = 0
ns
tSRDYSCKM1
Minimum Setup Time for SPIx_RDY Deassertion in Master
(2 + 2 × BAUD2) × tSCLK1 + 10
Mode Before Last Valid SPIx_CLK Edge of Valid Data Transfer to
Block Subsequent Transfer with CPHA = 1
ns
Switching Characteristic
tSRDYSCKM
1
2
Time Between Assertion of SPIx_RDY by Slave and First Edge 4.5 × tSCLK1
of SPIx_CLK for New SPI Transfer with CPHA/CPOL = 0 and
BAUD = 0 (STOP, LEAD, LAG = 0)
5.5 × tSCLK1 + 10
ns
Time Between Assertion of SPIx_RDY by Slave and First Edge 4 × tSCLK1
of SPIx_CLK for New SPI Transfer with CPHA/CPOL = 1 and
BAUD = 0 (STOP, LEAD, LAG = 0)
5 × tSCLK1 + 10
ns
Time Between Assertion of SPIx_RDY by Slave and First Edge (1 + 1.5 × BAUD2) × tSCLK1
of SPIx_CLK for New SPI Transfer with CPHA/CPOL = 0 and
BAUD ≥ 1 (STOP, LEAD, LAG = 0)
(2 + 2.5 × BAUD2) × tSCLK1 + 10 ns
Time Between Assertion of SPIx_RDY by Slave and First Edge (1 + 1 × BAUD2) × tSCLK1
of SPIx_CLK for New SPI Transfer with CPHA/CPOL = 1 and
BAUD ≥ 1 (STOP, LEAD, LAG = 0)
(2 + 2 × BAUD2) × tSCLK1 + 10 ns
All specifications apply to all three SPIs.
BAUD value set using the SPIx_CLK.BAUD bits. BAUD value = SPIx_CLK.BAUD bits + 1.
tSRDYSCKM0
SPIx_RDY
SPIx_CLK
(CPOL = 0)
SPIx_CLK
(CPOL = 1)
Figure 49. SPIx_RDY Setup Before SPIx_CLK with CPHA = 0
Rev. PrG
|
Page 126 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
tSRDYSCKM1
SPIx_RDY
SPIx_CLK
(CPOL = 0)
SPIx_CLK
(CPOL = 1)
Figure 50. SPIx_RDY Setup Before SPIx_CLK with CPHA = 1
tSRDYSCKM
SPIx_RDY
SPIx_CLK
(CPOL = 0)
SPIx_CLK
(CPOL = 1)
Figure 51. SPIx_CLK Switching Diagram after SPIx_RDY Assertion, CPHA = x
Rev. PrG
|
Page 127 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Precision Clock Generator (Direct Pin Routing)
This timing is only valid when the SRU is configured such that the precision clock generator (PCG) takes its inputs directly from the DAI
pins (via pin buffers) and sends its outputs directly to the DAI pins. For the other cases, where the PCG’s inputs and outputs are not
directly routed to/from DAI pins (via pin buffers), there is no timing data available. All timing parameters and switching characteristics
apply to external DAI pins (DAIx_PIN20-1).
Table 74. Precision Clock Generator (Direct Pin Routing)
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tPCGIP
Input Clock Period
tSTRIG
PCG Trigger Setup Before Falling Edge of PCG Input 4.5
Clock
tSCLK × 2
ns
ns
tHTRIG
PCG Trigger Hold After Falling Edge of PCG Input
Clock
ns
3
Switching Characteristics
tDPCGIO
PCG Output Clock and Frame Sync Active Edge Delay 2.5
After PCG Input Clock
13.5
ns
ns
tDTRIGCLK
PCG Output Clock Delay After PCG Trigger
2.5 + (2.5 × tPCGIP)
13.5 + (2.5 × tPCGIP)
tDTRIGFS
PCG Frame Sync Delay After PCG Trigger
2.5 + ((2.5 + D – PH) × tPCGIP)
13.5 + ((2.5 + D – PH) × tPCGIP) ns
tPCGOW1
Output Clock Period
2 × tPCGIP – 1
ns
D = FSxDIV, PH = FSxPHASE. For more information, see the “Precision Clock Generators” chapter of the hardware reference manual.
1
Normal mode of operation.
tSTRIG
tHTRIG
DAIx_PIN20–1
PCG_TRIGx_I
DAIx_PIN20–1
PCG_EXTx_I
(CLKIN)
tPCGIP
tDPCGIO
DAIx_PIN20–1
PCG_CLKx_O
tDTRIGCLK
tDPCGIO
DAIx_PIN20–1
PCG_FSx_O
tDTRIGFS
Figure 52. Precision Clock Generator (Direct Pin Routing)
Rev. PrG
|
Page 128 of 168 |
June 2016
tPCGOW
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
General-Purpose IO Port Timing
Table 75 and Figure 53 describe I/O timing, related to the general-purpose ports (PORT).
Table 75. General-Purpose Port Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirement
tWFI
General-Purpose Port Pin Input Pulse Width
2 × tSCLK0 – 1.5
ns
tWFI
GPIO INPUT
Figure 53. General-Purpose Port Timing
GPIO Timer Cycle Timing
Table 76, Table 77, and Figure 54 describe timer expired operations, related to the general-purpose timer (TIMER). The input signal is
asynchronous in “width capture mode” and “external clock mode” and has an absolute maximum input frequency of (fSCLK/4) MHz. The
Width Value value is the timer period assigned in the TMx_TMRn_WIDTH register and can range from 1 to 232 – 1. Note that when
externally generated, the TMR clock is called fTMRCLKEXT:
1
t TMRCLKEXT = -----------------------f TMRCLKEXT
Table 76. Timer Cycle Timing (Internal Mode)
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Timing Requirements
tWL
Timer Pulse Width Input Low (Measured In SCLK Cycles)1 2 × tSCLK
tWH
Timer Pulse Width Input High (Measured In SCLK Cycles)1 2 × tSCLK
Switching Characteristic
tHTO
Timer Pulse Width Output (Measured In SCLK Cycles)2
tSCLK × WIDTH – 1.5
Max
Unit
ns
ns
tSCLK × WIDTH + 1.5
ns
1
The minimum pulse width applies for TMx signals in width capture and external clock modes.
2
WIDTH refers to the value in the TMRx_WIDTH register (it can vary from 1 to 232 – 1).
Table 77. Timer Cycle Timing (External Mode)
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Timing Requirements
tWL
Timer Pulse Width Input Low (Measured In EXT_CLK Cycles)1 2 × tEXT_CLK
tWH
Timer Pulse Width Input High (Measured In EXT_CLK Cycles)1 2 × tEXT_CLK
tEXT_CLK
Timer External Clock Period2
tTMRCLKEXT
Switching Characteristic
tHTO
Timer Pulse Width Output (Measured In EXT_CLK Cycles)3
tEXT_CLK × WIDTH – 1.5
1
Max
Unit
ns
ns
ns
tEXT_CLK × WIDTH + 1.5
ns
The minimum pulse width applies for TMx signals in width capture and external clock modes.
2
This specification indicates the minimum instantaneous width or period that can be tolerated due to duty cycle variation or jitter on the external TMR_CLK. For the external
TMR_CLK maximum frequency see the fTMRCLKEXT specification in Table 29 in Clock Related Operating Conditions.
3
WIDTH refers to the value in the TMRx_WIDTH register (it can vary from 1 to 232 – 1).
Rev. PrG
|
Page 129 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
TMR OUTPUT
tHTO
TMR INPUT
tWH, tWL
Figure 54. Timer Cycle Timing
DAIx Pin to DAIx Pin Direct Routing (DAI0 and DAI1)
Table 78 and Figure 55 describe I/O timing, related to the digital audio interface (DAI). For direct pin connections only (for example
DAIx_PB01_I to DAIx_PB02_O).
Table 78. DAI/DAI Pin to Pin Routing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Timing Requirement
tDPIO
Delay DAI Pin Input Valid to DAI Output Valid
1.5
Max
Unit
12
ns
DAI_Pn
tDPIO
DAI_Pm
Figure 55. DAI Pin to Pin Direct Routing
Up/Down Counter/Rotary Encoder Timing
Table 79 and Figure 56 describe timing, related to the general-purpose counter (CNT).
Table 79. Up/Down Counter/Rotary Encoder Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirement
tWCOUNT
Up/Down Counter/Rotary Encoder Input Pulse Width
2 × tSCLK0
CNT0_UD
CNT0_DG
CNT0_ZM
tWCOUNT
Figure 56. Up/Down Counter/Rotary Encoder Timing
Rev. PrG
|
Page 130 of 168 |
June 2016
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Pulse Width Modulator (PWM) Timing
Table 80 and Figure 57 describe timing, related to the pulse width modulator (PWM).
Table 80. PWM Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirement
tES
External Sync Pulse Width
2 × tSCLK0
ns
Switching Characteristics
tDODIS
tDOE
Output Inactive (OFF) After Trip Input2
Output Delay After External Sync
2, 3
2 × tSCLK0 + 5.5
15
ns
5 × tSCLK0 + 14
ns
1
All specifications apply to all three PWMs.
PWM outputs are: PWMx_AH, PWMx_AL, PWMx_BH, PWMx_BL, PWMx_CH, and PWMx_CL.
3
When the external sync signal is synchronous to the peripheral clock, it takes fewer clock cycles for the output to appear compared to when the external sync signal is
asynchronous to the peripheral clock.
2
PWMx_SYNC
(AS INPUT)
tES
tDOE
OUTPUT
tDODIS
PWMx_TRIP
Figure 57. PWM Timing
Rev. PrG
|
Page 131 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Pulse Width Modulator (PWM)— Heightened-Precision Mode Timing
Table 81 and Table 82 and Figure 58 and Figure 59 describe heightened-precision pulse width modulator (PWM) operations.
Table 81. PWM—Heightened-Precision Mode, Output Pulse
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Switching Characteristics
tHPWMW
HP-PWM Output Pulse Width1, 2
(N + m × 0.25) × tSCLK – 0.5
(N + m × 0.25) × tSCLK + 0.5
Unit
ns
1
N is the DUTY bit field (coarse duty) from the duty register. m is the ENHDIV (Enhanced Precision Divider bits) value from the HP duty register.
2
Applies to individual PWM channel with 50% duty cycle. Other PWM channels within the same unit are toggling at the same time. No other GPIO pins are toggling.
PWMOUTPUT
t HPWMW
Figure 58. PWM Heightened-Precision Mode Timing, Output Pulse
Table 82. PWM—Heightened-Precision Mode, Output Skew
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Switching Characteristics
tHPWMS
HP-PWM Output Skew 1
1.0
1
Unit
ns
Output edge difference between any two PWM channels (AH, AL, BH, BL, CH, CL, DH and DL) in the same PWM unit (a unit is PWMx where x = 0, 1, 2), with the same
heightened-precision edge placement.
PWM OUTPUTS
t HPWMS
PWM OUTPUTS
Figure 59. PWM Heightened-Precision Mode Timing, Output Skew
Rev. PrG
|
Page 132 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ADC Controller Module (ACM) Timing
Table 83 and Figure 60 describe ADC control module (ACM) operations.
When internally generated, the programmed ACM clock (fACLKPROG) frequency in MHz is set by the following equation where CKDIV is
a field in the ACM_TC0 register and ranges from 1 to 255:
f SCLK1
f ACLKPROG = --------------------CKDIV + 1
1
t ACLKPROG = ----------------f ACLKPROG
Setup cycles (SC) in Table 83 is also a field in the ACM_TC0 register and ranges from 0 to 4095. Hold Cycles (HC) is a field in the
ACM_TC1 register that ranges from 0 to 15.
Table 83. ACM Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tSDR
SPORT DRxPRI/DRxSEC Setup Before ACMx_CLK
3.5
ns
tHDR
SPORT DRxPRI/DRxSEC Hold After ACMx_CLK
1.5
ns
ns
Switching Characteristics
1
tSCTLCS
ACM Controls (ACMx_A[4:0]) Setup Before Assertion of CS
(SC + 1) × tSCLK1 – 3
tHCTLCS
ACM Control (ACMx_A[4:0]) Hold After Deassertion of CS
HC × tACLKPROG – 1
ns
tACLKW
ACM Clock Pulse Width1
(0.5 × tACLKPROG) – 1.5
ns
tACLK
ACM Clock Period1
tACLKPROG – 1.5
ns
tHCSACLK
CS Hold to ACMx_CLK Edge
–2.5
ns
tSCSACLK
CS Setup to ACMx_CLK Edge
tACLKPROG – 3.5
ns
See Table 29 in Clock Related Operating Conditions on Page 81 for details on the minimum period that may be programmed for tACLKPROG.
DAIx_PIN20–1
(ACM0_FS/CS)
CSPOL = 1/0
tSCSACLK
DAIx_PIN20–1
(ACM_CLK)
CLKPOL = 1/0
tACLK
tACLKW
tHCSACLK
DAIx_PIN20–1
(ACM_A0-4)
tSDR
t SCTLCS
DAIx_PIN20–1
(ACM0_T0)
Figure 60. ACM Timing
Rev. PrG
|
Page 133 of 168 |
June 2016
tHDR
t HCTLCS
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Universal Asynchronous Receiver-Transmitter
(UART) Ports—Receive and Transmit Timing
The universal asynchronous receiver-transmitter (UART) ports receive and transmit operations are described in the hardware reference
manual.
Controller Area Network (CAN) Interface
The controller area network (CAN) interface timing is described in the hardware reference manual.
Rev. PrG
|
Page 134 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Universal Serial Bus (USB) On-The-Go—Receive and Transmit Timing
Table 84 describes the universal serial bus (USB) On-The-Go receive and transmit operations.
Table 84. USB On-The-Go—Receive and Transmit Timing1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
1
fUSBS
USB_XI Frequency
24
24
MHz
fsUSB
USB_XI Clock Frequency Stability
–50
+50
ppm
This specification is supported by USB0.
PCI Express (PCIe)
For more information about PCI Express (PCIe), see the following standards:
• PCI Express Base 3.0 Specification, Revision 1.0, PCI-SIG
• PCI Express 2.0 Card Electromechanical Specification, Revision 2.0, PCI-SIG
• PHY Interface for the PCI Express Architecture, Revision 2.0, Intel Corporation
• PCI-SIG Engineering Change Request: L1 Substates, February 1, 2012, PCI-SIG
• IEEE Standard 1149.1-2001, IEEE
• IEEE Standard 1149.6-2003, IEEE
Rev. PrG
|
Page 135 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
10/100 Ethernet MAC Controller (EMAC) Timing (ETH0 and ETH1)
Table 85 through Table 87 and Figure 61 through Figure 63 describe the 10/100 Ethernet MAC Controller (EMAC) operations.
Table 85. 10/100 Ethernet MAC Controller (EMAC) Timing: RMII Receive Signal1
All specifications are based on simulation data and are subject to change without notice.
Parameter2
Min
Max
Unit
None
50 + 1%
MHz
tREFCLK × 65%
Timing Requirements
1
2
tREFCLKF
ETHx_REFCLK Frequency (fSCLK0 = SCLK0 Frequency)
tREFCLKW
ETHx_REFCLK Width (tREFCLK = ETHx_REFCLK Period)
tREFCLK × 35%
tREFCLKIS
Rx Input Valid to RMII ETHx_REFCLK Rising Edge (Data In Setup)
1.75
ns
ns
tREFCLKIH
RMII ETHx_REFCLK Rising Edge to Rx Input Invalid (Data In Hold)
1.6
ns
These specifications apply to ETH0 and ETH1.
RMII inputs synchronous to RMII REF_CLK are ERxD1–0, RMII CRS_DV, and ERxER.
tREFCLK
ETH0_REFCLK
tREFCLKW
ETH0_RXD1–0
ETH0_CRS
tREFCLKIS
tREFCLKIH
Figure 61. 10/100 Ethernet MAC Controller Timing: RMII Receive Signal
Table 86. 10/100 Ethernet MAC Controller (EMAC) Timing: RMII Transmit Signal1
All specifications are based on simulation data and are subject to change without notice.
Parameter2
Min
Max
Unit
11.9
ns
Switching Characteristics
tREFCLKOV
RMII ETHx_REFCLK Rising Edge to Transmit Output Valid (Data Out Valid)
tREFCLKOH
RMII ETHx_REFCLK Rising Edge to Transmit Output Invalid (Data Out Hold)
2
1
These specifications apply to ETH0 and ETH1.
2
RMII outputs synchronous to RMII REF_CLK are ETxD1–0.
tREFCLK
ETH0_REFCLK
tREFCLKOH
ETH0_TXD1–0
ETH0_TXEN
tREFCLKOV
Figure 62. 10/100 Ethernet MAC Controller Timing: RMII Transmit Signal
Rev. PrG
|
Page 136 of 168 |
June 2016
ns
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Table 87. 10/100 Ethernet MAC Controller (EMAC) Timing: RMII Station Management1
All specifications are based on simulation data and are subject to change without notice.
Parameter2
Min
Max
Unit
Timing Requirements
tMDIOS
ETHx_MDIO Input Valid to ETHx_MDC Rising Edge (Setup)
10.8
ns
tMDCIH
ETHx_MDC Rising Edge to ETHx_MDIO Input Invalid (Hold)
0
ns
Switching Characteristics
1
2
tMDCOV
ETHx_MDC Falling Edge to ETHx_MDIO Output Valid
tMDCOH
ETHx_MDC Falling Edge to ETHx_MDIO Output Invalid (Hold)
tSCLK0 + 2
tSCLK0 –2.9
ns
ns
These specifications apply to ETH0 and ETH1.
ETHx_MDC/ETHx_MDIO is a 2-wire serial bidirectional port for controlling one or more external PHYs. ETHx_MDC is an output clock whose minimum period is
programmable as a multiple of the system clock SCLK0. ETHx_MDIO is a bidirectional data line.
ETH0_MDC
(OUTPUT)
tMDCOH
ETH0_MDIO
(OUTPUT)
tMDCOV
ETH0_MDIO
(INPUT)
tMDIOS
tMDCIH
Figure 63. 10/100 Ethernet MAC Controller Timing: RMII Station Management
Rev. PrG
|
Page 137 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Gigabit Ethernet MAC Controller (EMAC) Timing
Table 88 and Figure 64 describe the Gigabit Ethernet MAC Controller (EMAC) timing.
Table 88. Gigabit Ethernet MAC Controller (EMAC) Timing: RGMII 1
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
TsetupR
Data to Clock Input Setup at Receiver
1
ns
TholdR
Data to Clock Input Hold at Receiver
1
ns
tGREFCLKF
RGMII Receive Clock Period
8
ns
tGREFCLKW
RGMII Receive Clock Pulse Width
4
ns
– 0.5
ns
Switching Characteristics
1
TskewT_min
Data to Clock Output Skew at Transmitter MIN
TskewT_max
Data to Clock Output Skew at Transmitter MAX
0.5
ns
Tcyc
Clock Cycle Duration
7.2
8.8
ns
Duty_G
Duty Cycle for Gigabit MIN
0.45 × 8
0.55 × 8
ns
This specification is supported by ETH0 only (10/100/1000 Ethernet MAC Controller).
ETH_TXCLK
(AT TRANSMITTER)
TskewT
ETH_TXD0–3
TXD3–0
TXD8–5
TXD7–4
TXD4
TXEN
TXD9
TXERR
ETH_TXD0–3
ETH_TXCTL_TXEN
TskewR
ETH_TXCLK
(AT RECEIVER)
ETH_RXCLK_REFCLK
(AT TRANSMITTER)
TskewT
ETH_RXD0–3
RXD3–0
RXD8–5
RXD7–4
RXD4
RXEN
RXD9
RXERR
ETH_RXD0–3
ETH_RXCTL_CRS
TsetupR
TskewR
ETH_RXCLK_REFCLK
(AT RECEIVER)
TholdR
Figure 64. Gigabit Ethernet MAC Controller Timing: RGMII
Rev. PrG
|
Page 138 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Sinus Cardinalis (SINC) Filter Timing
The programmed sinus cardinalis (SINC) filter clock (fSINCLKPROG) frequency in MHz is set by the following equation where MDIV is a
field in the CLK Control register that can be set from 4 to 63:
f SCLK
f SINCLKPROG = ------------
MDIV
1
t SINCLKPROG = -------------------------f SINCLKPROG
Table 89. SINC Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Timing Requirements
tSSINC
SINC0_Dx Setup Before SINC0_CLKx Rise
13.5
tHSINC
SINC0_Dx Hold After SINC0_CLKx Rise
0
Switching Characteristics
tSINCLK
SINC0_CLKx Period1
tSINCLKPROG – 2.5
tSINCLKW
SINC0_CLKx Width1
0.5 × tSINCLKPROG – 2.5
1
Max
See Table 29 in Clock Related Operating Conditions on Page 81 for details on the minimum period that may be programmed for tSINCLKPROG.
tSINCLK
tSINCLKW
tSINCLKW
SINC0_CLKx
tSSINC
tHSINC
SINC_Dx
Figure 65. SINC Timing
Rev. PrG
|
Page 139 of 168 |
June 2016
Unit
ns
ns
ns
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Sony/Philips Digital Interface (S/PDIF) Transmitter
Serial data input to the Sony/Philips Digital Interface (S/PDIF) transmitter can be formatted as left-justified, I2S, or right-justified with
word widths of 16, 18, 20, or 24 bits. The following sections provide timing for the transmitter.
S/PDIF Transmitter-Serial Input Waveforms
Figure 66 shows the right-justified mode. Frame sync is high for the left channel and low for the right channel. Data is valid on the rising
edge of serial clock. The MSB is delayed the minimum in 24-bit output mode or the maximum in 16-bit output mode from a frame sync
transition, so that when there are 64 serial clock periods per frame sync period, the LSB of the data is right-justified to the next frame sync
transition.
Table 90. S/PDIF Transmitter Right-Justified Mode
All specifications are based on simulation data and are subject to change without notice.
Parameter
Timing Requirement
tRJD
Frame Sync to MSB Delay in Right-Justified Mode
16-Bit Word Mode
18-Bit Word Mode
20-Bit Word Mode
24-Bit Word Mode
Nominal
Unit
16
14
12
8
SCLK
SCLK
SCLK
SCLK
LEFT/RIGHT CHANNEL
DAI_P20–1
FS
DAI_P20–1
SCLK
tRJD
DAI_P20–1
SDATA
LSB
MSB
MSB–1
MSB–2
Figure 66. Right-Justified Mode
Rev. PrG
|
Page 140 of 168 |
June 2016
LSB+2
LSB+1
LSB
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Figure 67 shows the default I2S-justified mode. The frame sync is low for the left channel and HI for the right channel. Data is valid on the
rising edge of serial clock. The MSB is left-justified to the frame sync transition but with a delay.
Table 91. S/PDIF Transmitter I2S Mode
All specifications are based on simulation data and are subject to change without notice.
Parameter
Nominal
Timing Requirement
tI2SD
Frame Sync to MSB Delay in I2S Mode
1
Unit
SCLK
LEFT/RIGHT CHANNEL
DAI_P20–1
FS
DAI_P20–1
SCLK
tI2SD
DAI_P20–1
SDATA
MSB
MSB–1
MSB–2
LSB+2
LSB+1
LSB
Figure 67. I2S-Justified Mode
Figure 68 shows the left-justified mode. The frame sync is high for the left channel and low for the right channel. Data is valid on the rising
edge of serial clock. The MSB is left-justified to the frame sync transition with no delay.
Table 92. S/PDIF Transmitter Left-Justified Mode
All specifications are based on simulation data and are subject to change without notice.
Parameter
Nominal
Timing Requirement
tLJD
Frame Sync to MSB Delay in Left-Justified Mode
0
DAI_P20–1
FS
LEFT/RIGHT CHANNEL
DAI_P20–1
SCLK
tLJD
DAI_P20–1
SDATA
MSB
MSB–1
MSB–2
LSB+2
LSB+1
Figure 68. Left-Justified Mode
Rev. PrG
|
Page 141 of 168 |
June 2016
LSB
Unit
SCLK
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
S/PDIF Transmitter Input Data Timing
The timing requirements for the S/PDIF transmitter are given in Table 93. Input signals are routed to the DAIx_Pin20–1 pins using the
SRU. Therefore, the timing specifications provided below are valid at the DAIx_Pin20–1 pins.
Table 93. S/PDIF Transmitter Input Data Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
1
tSISFS1
Frame Sync Setup Before Serial Clock Rising Edge
3
ns
tSIHFS1
Frame Sync Hold After Serial Clock Rising Edge
3
ns
tSISD1
Data Setup Before Serial Clock Rising Edge
3
ns
tSIHD1
Data Hold After Serial Clock Rising Edge
3
ns
tSITXCLKW
Transmit Clock Width
9
ns
tSITXCLK
Transmit Clock Period
20
ns
tSISCLKW
Clock Width
36
ns
tSISCLK
Clock Period
80
ns
The serial clock, data, and frame sync signals can come from any of the DAI pins. The serial clock and frame sync signals can also come via PCG or SPORTs. PCG’s input can
be either CLKIN or any of the DAI pins.
SAMPLE EDGE
tSITXCLKW
tSITXCLK
DAIx_PIN20–1
(TxCLK)
tSISCLK
tSISCLKW
DAIx_PIN20–1
(SCLK)
tSISFS
tSIHFS
DAIx_PIN20–1
(FS)
tSISD
tSIHD
DAIx_PIN20–1
(SDATA)
Figure 69. S/PDIF Transmitter Input Timing
Rev. PrG
|
Page 142 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Sony/Philips Digital Interface (S/PDIF) Receiver
The following section describes timing as it relates to the Sony/Philips Digital Interface (S/PDIF) receiver.
Internal Digital PLL Mode
In the internal digital phase-locked loop mode the internal PLL (digital PLL) generates the 512 × FS clock.
Table 94. S/PDIF Receiver Internal Digital PLL Mode Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
5
ns
Switching Characteristics
tDFSI
Frame Sync Delay After Serial Clock
tHOFSI
Frame Sync Hold After Serial Clock
tDDTI
Transmit Data Delay After Serial Clock
tHDTI
Transmit Data Hold After Serial Clock
–2
5
–2
SAMPLE EDGE
DRIVE EDGE
DAIx_PIN20–1
(SCLK)
tDFSI
tHOFSI
DAIx_PIN20–1
(FS)
tDDTI
tHDTI
DAIx_PIN20–1
(DATA CHANNEL
A/B)
Figure 70. S/PDIF Receiver Internal Digital PLL Mode Timing
Rev. PrG
|
Page 143 of 168 |
ns
June 2016
ns
ns
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Media Local Bus (MLB)
All the numbers given are applicable for all media local bus (MLB) speed modes (1024 FS, 512 FS, and 256 FS) for 3-pin, unless otherwise
specified. Please refer to the Media Local Bus Specification version 4.2 for more details.
Table 95. MLB Interface, 3-Pin Specifications
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Typ
MLB Clock Period
tMLBCLK
20.3
1024 FS
40
512 FS
81
256 FS
tMCKL
tMCKH
tMCKR
tMCKF
tMPWV1
tDSMCF
tDHMCF
tMCFDZ
tMCDRV
tMDZH2
CMLB
1
2
MLBCLK Low Time
1024 FS
512 FS
256 FS
MLBCLK High Time
1024 FS
512 FS
256 FS
MLBCLK Rise Time (VIL to VIH)
1024 FS
512 FS/256 FS
MLBCLK Fall Time (VIH to VIL)
1024 FS
512 FS/256 FS
MLBCLK Pulse Width Variation
1024 FS
512 FS/256
DAT/SIG Input Setup Time
DAT/SIG Input Hold Time
DAT/SIG Output Time to Three-state
DAT/SIG Output Data Delay From MLBCLK Rising Edge
Bus Hold Time
1024 FS
512 FS/256
DAT/SIG Pin Load
1024 FS
512 FS/256
Max
Unit
ns
ns
ns
6.1
14
30
ns
ns
ns
9.3
14
30
ns
ns
ns
1
2
0
1
3
ns
ns
1
3
ns
ns
0.7
2.0
nspp
nspp
15
8
ns
ns
ns
ns
2
4
ns
ns
40
60
pf
pf
Pulse width variation is measured at 1.25 V by triggering on one edge of MLBCLK and measuring the spread on the other edge, measured in ns peak-to-peak (pp).
The board must be designed to ensure that the high-impedance bus does not leave the logic state of the final driven bit for this time period. Therefore, coupling must be
minimized while meeting the maximum capacitive load listed.
Rev. PrG
|
Page 144 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
MLB_SIG/
MLB_DAT
(Rx, Input)
VALID
tDHMCF
tDSMCF
tMCKH
MLB_CLK
tMCKR
tMCKL
tMCKF
tMLBCLK
tMCFDZ
tMCDRV
tMDZH
MLB_SIG/
MLB_DAT
(Tx, Output)
VALID
Figure 71. Media Local Bus Timing (3-Pin Interface)
The ac timing specifications of MLB 6-pin interface is detailed below. Please refer to the Media Local Bus Specification version 4.2 for
more details.
Table 96. MLB Interface, 6-Pin Specifications
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Typ
Max
Unit
tMT
Differential transition time at the input pin
1
ns
(Figure 72)
MLBCP/N external clock operating
67.584
102.4
MHz
fMCKE
frequency1 (Figure 73)
fMCKR
Recovered clock operating frequency
90.112
(internal, not observable at pins, only for 135.168
timing references) (Figure 73)
102.4
204.8
MHz
MHz
tDELAY
Transmitter MLBSP/N (MLBDP/N) output
valid from transition of MLBCP/N (low-tohigh)2 (Figure 74)
Disable turnaround time from transition of
MLBCP/N (low-to-high)2 (Figure 75)
5
2.5
ns
ns
7
3.5
11.2
5.6
ns
ns
ns
ns
ns
ns
ns
tPHZ
tPLZ
tSU
tHD
0.6
0.6
0.6
0.6
Enable turnaround time from transition of 0.6
MLBCP/N (low-to-high)2 (Figure 75)
0.6
MLBSP/N (MLBDP/N) valid to transition of 1
MLBCP/N (low-to-high)2 (Figure 74)
0.5
MLBSP/N (MLBDP/N) hold from transition 0.6
of MLBCP/N (low-to-high)2, 3 (Figure 74)
1
Comment
20% to 80% VIN+/–
80% to 20% VIN+/–
1536 × FS at 44.0 kHz
2048 × FS at 50.0 kHz
2048 × FS at 50.0 kHz
3072 × FS at 44.0 kHz
4096 × FS at 50.0 kHz
when fMCKR = 2048 × FS
when fMCKR = 3072 × FS or 4096 × FS
when fMCKR = 2048 × FS
when fMCKR = 3072 × FS or 4096 × FS
when fMCKR = 2048 × FS
when fMCKR = 3072 × FS or 4096 × FS
when fMCKR = 2048 × FS
when fMCKR = 3072 × FS or 4096 × FS
fMCKE (max) and fMCKR (max) include maximum cycle-to-cycle system jitter (tJITTER) of 600ps for a bit error rate of 10E-9.
tDELAY, tPHZ, tPLZ, tSU, tHD may also be referenced from a low-to-high transition of the recovered clock for 2:1 recovered to external clock ratios.
3
Receivers must latch MLBSP/N (MLBDP/N) data within tHD (min) of the rising edge of MLBCP/N.
2
Rev. PrG
|
Page 145 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
MLBCP/N
MLBDP/N
MLBSP/N
tMT
tMT
80%
20%
Figure 72. Media Local Bus 6-Pin Transition Time
MLBCP/N
1/fMCKE
RECOVERED
CLOCK (1:1)
RECOVERED
CLOCK (2:1)
T1:1
T2:1
T2:1
NOTE: T1:1 = 1/fMCKE
T2:1 = 1/(2 × fMCKE)
Figure 73. Media Local Bus 6-Pin Clock Definitions
Rev. PrG
|
Page 146 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
1/fMCKE
MLBCP/N
RECOVERED
CLOCK
1/fMCKR
tDELAY
tDELAY
MLBSP/N
MLBDP/N
(TRANSMIT)
tSU
tSU
MLBSP/N
MLBDP/N
(RECEIVE)
VALID
VALID
tHD
tHD
1/fMCKE
MLBCP/N
1/fMCKR
RECOVERED
CLOCK
tDELAY
tDELAY
MLBSP/N
MLBDP/N
(TRANSMIT)
tSU
MLBSP/N
MLBDP/N
(RECEIVE)
VALID
VALID
tHD
tHD
Figure 74. Media Local Bus 6-Pin Delay, Setup, and Hold Times
Rev. PrG
|
Page 147 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
MLBCP/N
RECOVERED
CLOCK (1:1)
tPHZ
MLBDP/N
MLNSP/N
tPLZ
MLBCP/N
RECOVERED
CLOCK (2:1)
tPHZ
MLBDP/N
MLNSP/N
tPLZ
Figure 75. Media Local Bus 6-Pin Disable and Enable Turnaround Times
Rev. PrG
|
Page 148 of 168 |
June 2016
Preliminary Technical Data
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Mobile Storage Interface (MSI) Controller Timing
Table 97 and Figure 76 show I/O timing, related to the mobile storage interface (MSI).
Table 97. MSI Controller Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tISU
Input Setup Time
4.8
ns
tIH
Input Hold Time
–0.5
ns
Switching Characteristics
1
fPP
Clock Frequency Data Transfer Mode1
50
MHz
tWL
Clock Low Time
8
ns
tWH
Clock High Time
8
ns
tTLH
Clock Rise Time
3
ns
tTHL
Clock Fall Time
3
ns
tODLY
Output Delay Time During Data Transfer Mode
2
ns
tOH
Output Hold Time
–1.8
ns
tPP = 1/fPP
VOH (MIN)
tPP
MSI_CLK
tTHL
tISU
tTLH
tWL
tIH
VOL (MAX)
tWH
INPUT
tODLY
tOH
OUTPUT
NOTES:
1 INPUT INCLUDES MSI_Dx AND MSI_CMD SIGNALS.
2 OUTPUT INCLUDES MSI_Dx AND MSI_CMD SIGNALS.
Figure 76. MSI Controller Timing
Rev. PrG
|
Page 149 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Program Trace Macrocell (PTM) Timing
Table 98 and Figure 77 provide I/O timing, related to the program trace macrocell (PTM).
Table 98. Trace Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
5
ns
Switching Characteristics
tDTRD
TRACE Data Delay From Trace Clock MAX
tHTRD
TRACE Data Hold From Trace Clock MIN
2
ns
tPTRCK
TRACE Clock Period MIN
12.32
ns
tPTRCK
TRACE0_CLK
tHTRD
D0
TRACE0_DX
tDTRD
D1
tDTRD
Figure 77. Trace Timing
Rev. PrG
|
tHTRD
Page 150 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Debug Interface (JTAG Emulation Port) Timing
Table 99 and Figure 78 provide I/O timing, related to the debug interface (JTAG Emulator Port).
Table 99. JTAG Port Timing
All specifications are based on simulation data and are subject to change without notice.
Parameter
Min
Max
Unit
Timing Requirements
tTCK
JTG_TCK Period
20
tSTAP
JTG_TDI, JTG_TMS Setup Before JTG_TCK High
4
ns
tHTAP
JTG_TDI, JTG_TMS Hold After JTG_TCK High
4
ns
tSSYS
System Inputs Setup Before JTG_TCK High1
4
ns
4
ns
4
TCK
1
tHSYS
System Inputs Hold After JTG_TCK High
tTRSTW
JTG_TRST Pulse Width (measured in JTG_TCK cycles)2
ns
Switching Characteristics
tDTDO
JTG_TDO Delay from JTG_TCK Low
System Outputs Delay After JTG_TCK Low
tDSYS
3
1
12
ns
17
ns
System Inputs = MLB0_CLKP, MLB0_DATP, MLB0_SIGP, DAI0_PIN20-01, DAI1_PIN20-01, DMC0_A15-0, DMC1_A15-0, DMC0_DQ15-0, DMC1_DQ15-0,
DMC0_RESET, DMC1_RESET, PA_15-0, PB_15-0, PC_15-0, PD_15-0, PE_15-0, PF_15-0, PG_5-0, SYS_BMODE2-0, SYS_FAULT, SYS_FAULT, SYS_RESOUT,
TWI2-0_SCL, TWI2-0_SDA2.
2
50 MHz Maximum.
3
System Outputs = DMC0_A15-0, DMC0_BA2-0, DMC0_CAS, DMC0_CK, DMC0_CKE, DMC0_CS0, DMC0_DQ15-0, DMC0_LDM, DMC0_LDQS, DMC0_ODT,
DMC0_RAS, DMC0_RESET, DMC0_UDM, DMC0_UDQS, DMC0_WE, DMC1_A15-0, DMC1_BA2-0, DMC1_CAS, DMC1_CK, DMC1_CKE, DMC1_CS0,
DMC1_DQ15-0, DMC1_LDM, DMC1_LDQS, DMC1_ODT, DMC1_RAS, DMC1_RESET, DMC1_UDM, DMC1_UDQS, DMC1_WE, MLB0_DATP, MLB0_SIGP,
PA_15-0, PB_15-0, PC_15-0, PCIE_TXP, PD_15-0, PE_15-0, PF_15-0, PG_5-0, SYS_BMODE2-0, SYS_CLKOUT, SYS_FAULT, SYS_FAULT, SYS_RESOUT, TWI2-0_SCL,
TWI2-0_SDA.
tTCK
JTG_TCK
tSTAP
tHTAP
JTG_TMS
JTG_TDI
tDTDO
JTG_TDO
tSSYS
tHSYS
SYSTEM
INPUTS
tDSYS
SYSTEM
OUTPUTS
Figure 78. JTAG Port Timing
Rev. PrG
|
Page 151 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ENVIRONMENTAL CONDITIONS
Table 101. Thermal Characteristics for ADSP-SC589
19 mm × 19 mm 529 CSP_BGA
To determine the junction temperature on the application
printed circuit board, use the following equation:
Parameter
JA
JA
JA
JC
JT
JT
JT
T J = T CASE +   JT  P D 
where:
TJ = Junction temperature (°C).
TCASE = Case temperature (°C) measured by customer at top
center of package.
JT = From Table 100 and Table 101.
PD = Power dissipation (see Total Internal Power Dissipation
for the method to calculate PD).
Values of JA are provided for package comparison and printed
circuit board design considerations. JA can be used for a first
order approximation of TJ by the equation:
T J = T A +   JA  P D 
where:
TA = ambient temperature (°C).
Values of JC are provided for package comparison and printed
circuit board design considerations when an external heat sink
is required.
In Table 100 and Table 101, airflow measurements comply with
JEDEC standards JESD51-2 and JESD51-6. The junction-tocase measurement complies with MIL-STD-883 (Method
1012.1). All measurements use a 6 layer PCB with
101.6 mm × 152.4 mm dimensions.
Table 100. Thermal Characteristics for ADSP-SC584
19 mm × 19 mm 349 CSP_BGA
Parameter
JA
JA
JA
JC
JT
JT
JT
Conditions
0 linear m/s air flow
1 linear m/s air flow
2 linear m/s air flow
0 linear m/s air flow
1 linear m/s air flow
2 linear m/s air flow
Typical
13.3
12.1
11.6
3.65
0.08
0.12
0.14
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
Rev. PrG
Preliminary Technical Data
|
Page 152 of 168 |
June 2016
Conditions
0 linear m/s air flow
1 linear m/s air flow
2 linear m/s air flow
0 linear m/s air flow
1 linear m/s air flow
2 linear m/s air flow
Typical
13.4
12.1
11.6
3.63
0.08
0.11
0.13
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ADSP-SC58x/ADSP-2158x 349-BALL BGA BALL ASSIGNMENTS
ADSP-SC58x/ADSP-2158x 349-Ball BGA Ball Assignments
(Numerical by Ball Number) lists the 349-ball BGA package by
ball number.
ADSP-SC58x/ADSP-2158x 349-Ball BGA Ball Assignments
(Alphabetical by Pin Name) lists the 349-ball BGA package by
pin name.
ADSP-SC58x/ADSP-2158x 349-BALL BGA BALL ASSIGNMENTS (NUMERICAL BY BALL NUMBER)
Ball No.
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
Pin Name
GND
DMC0_A06
DMC0_A04
DMC0_RAS
DMC0_CKE
DMC0_DQ15
DMC0_DQ13
DMC0_UDQS
DMC0_UDQS
DMC0_DQ09
DMC0_VREF
DMC0_CK
DMC0_CK
DMC0_DQ06
DMC0_LDQS
DMC0_LDQS
DMC0_DQ01
GND
PD_00
PD_03
PD_06
GND
DMC0_A07
GND
DMC0_A02
DMC0_A00
DMC0_ODT
DMC0_DQ14
DMC0_DQ12
GND
DMC0_DQ11
DMC0_DQ10
DMC0_DQ08
DMC0_DQ07
DMC0_DQ05
DMC0_DQ04
DMC0_DQ03
DMC0_DQ02
DMC0_DQ00
PC_13
PD_02
Ball No.
B20
B21
B22
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
D01
D02
D03
D11
D12
D20
D21
D22
E01
E02
E03
E05
E20
E21
E22
F01
Pin Name
PD_05
GND
PD_08
DMC0_A10
DMC0_A09
GND
DMC0_A08
DMC0_A03
DMC0_CAS
DMC0_BA0
DMC0_A01
DMC0_RZQ
DMC0_WE
DMC0_CS0
GND
DMC0_LDM
DMC0_UDM
PD_01
PC_14
SYS_CLKOUT
PC_15
PD_04
GND
PD_07
PD_11
DMC0_A11
DMC0_A12
DMC0_BA2
VDD_INT
VDD_INT
PD_10
PD_09
PD_12
DMC0_A14
DMC0_A15
DMC0_A13
DMC0_A05
VDD_INT
PD_13
PD_14
DMC0_RESET
Rev. PrG
|
Ball No.
F02
F03
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F20
F21
F22
G01
G02
G03
G06
G07
G08
G09
G10
G11
G12
G13
G14
G15
G16
G17
G20
G21
G22
H01
H02
H03
H06
H07
H16
Page 153 of 168 |
Pin Name
PC_11
DMC0_BA1
VDD_DMC
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_DMC
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
PD_15
PE_00
PC_12
PC_10
PC_04
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_INT
PE_01
PE_02
PC_08
PC_07
SYS_FAULT
VDD_DMC
VDD_DMC
GND
June 2016
Ball No.
H17
H20
H21
H22
J01
J02
J03
J06
J09
J10
J11
J12
J13
J14
J17
J20
J21
J22
K01
K02
K03
K06
K08
K09
K10
K11
K12
K13
K14
K15
K17
K20
K21
K22
L01
L02
L03
L04
L06
L08
L09
Pin Name
VDD_DMC
VDD_INT
PE_03
PE_04
PC_05
PC_06
JTG_TDI
VDD_DMC
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PE_05
PE_06
PC_03
PC_02
SYS_FAULT
VDD_INT
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PE_08
PE_07
PC_01
SYS_HWRST
PC_09
VDD_INT
VDD_INT
GND
GND
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Ball No.
L10
L11
L12
L13
L14
L15
L17
L19
L20
L21
L22
M01
M02
M03
M04
M06
M08
M09
M10
M11
M12
M13
M14
M15
M17
M19
M20
M21
M22
N01
N02
N03
N06
N08
N09
N10
N11
N12
N13
N14
N15
N17
N20
N21
N22
P01
P02
Pin Name
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PE_11
PE_10
PE_09
JTG_TRST
JTG_TMS
JTG_TCK
VDD_INT
VDD_INT
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PE_13
PE_15
PE_12
SYS_XTAL1
SYS_BMODE0
PC_00
VDD_EXT
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
DAI1_PIN04
DAI1_PIN02
PE_14
SYS_CLKIN1
SYS_BMODE1
Ball No.
P03
P06
P09
P10
P11
P12
P13
P14
P17
P20
P21
P22
R01
R02
R03
R06
R07
R16
R17
R20
R21
R22
T01
T02
T03
T06
T07
T08
T09
T10
T11
T12
T13
T14
T15
T16
T17
T20
T21
T22
U01
U02
U03
U06
U07
U08
U09
Pin Name
JTG_TDO
VDD_EXT
GND
GND
GND
GND
GND
GND
VDD_EXT
DAI1_PIN01
DAI1_PIN05
DAI1_PIN03
GND
PB_15
PB_14
VDD_EXT
GND
GND
VDD_EXT
DAI1_PIN08
DAI1_PIN07
DAI1_PIN06
SYS_XTAL0
SYS_BMODE2
DAI0_PIN07
VDD_EXT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
DAI1_PIN12
DAI1_PIN10
DAI1_PIN09
SYS_CLKIN0
SYS_RESOUT
PB_07
VDD_EXT
VDD_EXT
VDD_USB
VDD_INT
Rev. PrG
|
Ball No.
U10
U11
U12
U13
U14
U15
U16
U17
U20
U21
U22
V01
V02
V03
V20
V21
V22
W01
W02
W03
W11
W12
W20
W21
W22
Y01
Y02
Y03
Y04
Y05
Y06
Y07
Y08
Y09
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y20
Y21
Y22
Page 154 of 168 |
Pin Name
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
DAI1_PIN20
DAI1_PIN11
DAI1_PIN19
PB_13
PB_12
DAI0_PIN20
PA_00
PA_01
PA_02
PB_10
PB_11
DAI0_PIN19
VDD_INT
VDD_INT
PA_05
PA_03
PA_04
PB_09
PB_08
DAI0_PIN12
DAI0_PIN06
DAI0_PIN02
DAI0_PIN03
DAI0_PIN01
USB0_VBC
TWI0_SCL
TWI1_SDA
VDD_HADC
GND
HADC0_VIN6
PB_06
PB_00
PB_04
PB_01
PA_10
PA_15
GND
PA_06
PA_08
June 2016
Preliminary Technical Data
Ball No.
AA01
AA02
AA03
AA04
AA05
AA06
AA07
AA08
AA09
AA10
AA11
AA12
AA13
AA14
AA15
AA16
AA17
AA18
AA19
AA20
AA21
AA22
AB01
AB02
AB03
AB04
AB05
AB06
AB07
AB08
AB09
AB10
AB11
AB12
AB13
AB14
AB15
AB16
AB17
AB18
AB19
AB20
AB21
AB22
Pin Name
DAI0_PIN11
GND
DAI0_PIN10
DAI0_PIN04
DAI0_PIN05
USB0_ID
USB0_VBUS
TWI2_SCL
TWI2_SDA
TWI0_SDA
HADC0_VIN2
HADC0_VIN5
HADC0_VIN4
HADC0_VIN7
PB_05
PB_02
PA_14
PB_03
PA_12
PA_11
GND
PA_09
GND
DAI0_PIN09
DAI0_PIN08
USB_CLKIN
USB_XTAL
USB0_DP
USB0_DM
TWI1_SCL
HADC0_VREFP
HADC0_VREFN
HADC0_VIN0
HADC0_VIN1
HADC0_VIN3
MLB0_SIGP
MLB0_SIGN
MLB0_DATP
MLB0_DATN
MLB0_CLKP
MLB0_CLKN
PA_13
PA_07
GND
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ADSP-SC58x/ADSP-2158x 349-BALL BGA BALL ASSIGNMENTS (ALPHABETICAL BY PIN NAME)
Pin Name
DAI0_PIN01
DAI0_PIN02
DAI0_PIN03
DAI0_PIN04
DAI0_PIN05
DAI0_PIN06
DAI0_PIN07
DAI0_PIN08
DAI0_PIN09
DAI0_PIN10
DAI0_PIN11
DAI0_PIN12
DAI0_PIN19
DAI0_PIN20
DAI1_PIN01
DAI1_PIN02
DAI1_PIN03
DAI1_PIN04
DAI1_PIN05
DAI1_PIN06
DAI1_PIN07
DAI1_PIN08
DAI1_PIN09
DAI1_PIN10
DAI1_PIN11
DAI1_PIN12
DAI1_PIN19
DAI1_PIN20
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_A14
DMC0_A15
DMC0_BA0
DMC0_BA1
Ball No.
Y07
Y05
Y06
AA04
AA05
Y04
T03
AB03
AB02
AA03
AA01
Y03
W03
V03
P20
N21
P22
N20
P21
R22
R21
R20
T22
T21
U21
T20
U22
U20
B04
C08
B03
C05
A03
E05
A02
B01
C04
C02
C01
D01
D02
E03
E01
E02
C07
F03
Pin Name
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_RESET
DMC0_RZQ
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_VREF
DMC0_WE
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Ball No.
D03
C06
A13
A05
A12
C11
B17
A17
B16
B15
B14
B13
A14
B12
B11
A10
B10
B09
B07
A07
B06
A06
C13
A16
A15
B05
A04
F01
C09
C14
A09
A08
A11
C10
A01
A18
A22
AA02
AA21
AB01
AB22
B02
B08
B21
C03
C12
Rev. PrG
|
Pin Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Page 155 of 168 |
June 2016
Ball No.
C20
H16
J09
J10
J11
J12
J13
J14
K08
K09
K10
K11
K12
K13
K14
K15
L08
L09
L10
L11
L12
L13
L14
L15
M08
M09
M10
M11
M12
M13
M14
M15
N08
N09
N10
N11
N12
N13
N14
N15
P09
P10
P11
P12
P13
P14
Pin Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
HADC0_VIN0
HADC0_VIN1
HADC0_VIN2
HADC0_VIN3
HADC0_VIN4
HADC0_VIN5
HADC0_VIN6
HADC0_VIN7
HADC0_VREFN
HADC0_VREFP
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
MLB0_CLKN
MLB0_CLKP
MLB0_DATN
MLB0_DATP
MLB0_SIGN
MLB0_SIGP
PA_00
PA_01
PA_02
PA_03
PA_04
PA_05
PA_06
PA_07
PA_08
PA_09
Ball No.
R01
R07
R16
T07
T08
T09
T10
T11
T12
T13
T14
T15
T16
Y12
Y20
AB11
AB12
AA11
AB13
AA13
AA12
Y13
AA14
AB10
AB09
M03
J03
P03
M02
M01
AB19
AB18
AB17
AB16
AB15
AB14
V20
V21
V22
W21
W22
W20
Y21
AB21
Y22
AA22
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Pin Name
PA_10
PA_11
PA_12
PA_13
PA_14
PA_15
PB_00
PB_01
PB_02
PB_03
PB_04
PB_05
PB_06
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
PB_15
PC_00
PC_01
PC_02
PC_03
PC_04
PC_05
PC_06
PC_07
PC_08
PC_09
PC_10
PC_11
PC_12
PC_13
PC_14
PC_15
PD_00
PD_01
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
Ball No.
Y18
AA20
AA19
AB20
AA17
Y19
Y15
Y17
AA16
AA18
Y16
AA15
Y14
U03
Y02
Y01
W01
W02
V02
V01
R03
R02
N03
L01
K02
K01
G03
J01
J02
H02
H01
L03
G02
F02
G01
B18
C16
C18
A19
C15
B19
A20
C19
B20
A21
C21
B22
Pin Name
PD_09
PD_10
PD_11
PD_12
PD_13
PD_14
PD_15
PE_00
PE_01
PE_02
PE_03
PE_04
PE_05
PE_06
PE_07
PE_08
PE_09
PE_10
PE_11
PE_12
PE_13
PE_14
PE_15
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
SYS_FAULT
SYS_FAULT
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
TWI2_SCL
TWI2_SDA
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
USB_CLKIN
Ball No.
D21
D20
C22
D22
E21
E22
F21
F22
G21
G22
H21
H22
J21
J22
K22
K21
L22
L21
L20
M22
M20
N22
M21
N02
P02
T02
U01
P01
C17
H03
K03
L02
U02
T01
N01
Y09
AA10
AB08
Y10
AA08
AA09
AB07
AB06
AA06
Y08
AA07
AB04
Rev. PrG
|
Pin Name
USB_XTAL
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_HADC
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
Page 156 of 168 |
June 2016
Preliminary Technical Data
Ball No.
AB05
F06
F11
G06
G07
G08
G09
G10
G11
G12
G13
G14
G15
G16
G17
H06
H07
H17
J06
J17
K17
L17
M17
N06
N17
P06
P17
R06
R17
T06
T17
U06
U07
U14
U15
U16
U17
Y11
D11
D12
E20
F07
F08
F09
F10
F12
F13
Pin Name
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_USB
Ball No.
F14
F15
F16
F17
F20
G20
H20
J20
K06
K20
L04
L06
L19
M04
M06
M19
U09
U10
U11
U12
U13
W11
W12
U08
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
CONFIGURATION OF THE 349-BALL CSP_BGA
Figure 79 shows an overview of signal placement on the 349-ball CSP_BGA.
TOP VIEW
A1 BALL
CORNER
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22
A
B
C
D
E
F
GND
G
I/O SIGNALS
H
J
VDD_EXT
K
VDD_INT
L
VDD_DDR
M
U
VDD_USB
N
H
VDD_HADC
P
R
T
U
U
V
W
Y
H
AA
AB
22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
A1 BALL
CORNER
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
U
V
W
Y
H
AA
AB
BOTTOM VIEW
Figure 79. 349-Ball CSP_BGA Configuration
Rev. PrG
|
Page 157 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
ADSP-SC58x/ADSP-2158x 529-BALL BGA BALL ASSIGNMENTS
ADSP-SC58x/ADSP-2158x 529-Ball BGA Ball Assignments
(Numerical by Ball Number) lists the 529-ball BGA package by
ball number.
ADSP-SC58x/ADSP-2158x 529-Ball BGA Ball Assignments
(Alphabetical by Pin Name) lists the 529-ball BGA package by
pin name.
ADSP-SC58x/ADSP-2158x 529-BALL BGA BALL ASSIGNMENTS (NUMERICAL BY BALL NUMBER)
Ball No.
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B13
B14
B15
B16
B17
B18
Pin Name
GND
DMC0_UDQS
DMC0_CK
DMC0_CK
DMC0_DQ09
DMC0_LDQS
DMC0_LDQS
DMC0_DQ05
DMC0_DQ03
DMC0_DQ01
DMC1_DQ03
DMC1_DQ00
DMC1_LDQS
DMC1_LDQS
DMC1_VREF
DMC1_CK
DMC1_CK
DMC1_DQ09
DMC1_UDQS
DMC1_UDQS
DMC1_DQ13
DMC1_DQ15
GND
DMC0_UDQS
DMC0_DQ12
DMC0_DQ11
DMC0_DQ10
DMC0_DQ08
DMC0_DQ06
DMC0_DQ07
DMC0_DQ04
DMC0_DQ02
DMC0_DQ00
DMC1_DQ01
DMC1_DQ02
DMC1_DQ04
DMC1_DQ05
DMC1_DQ06
DMC1_DQ07
DMC1_DQ08
DMC1_DQ10
Ball No.
B19
B20
B21
B22
B23
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
D01
D02
D03
D04
D05
D06
D07
D08
D09
D10
D11
D12
D13
Pin Name
DMC1_DQ11
DMC1_DQ12
DMC1_DQ14
PD_00
PD_04
DMC0_DQ14
DMC0_DQ13
DMC0_CS0
DMC0_CKE
DMC0_LDM
DMC1_RESET
DMC1_A03
DMC1_A00
DMC1_A01
DMC1_A04
DMC1_A06
DMC1_BA1
DMC1_ODT
DMC1_CS0
DMC1_LDM
DMC1_UDM
DMC1_A14
DMC1_A12
DMC1_A13
PC_13
PD_01
PD_06
PD_05
DMC0_VREF
DMC0_DQ15
DMC0_BA0
DMC0_BA2
DMC0_ODT
DMC0_UDM
DMC1_A05
DMC1_WE
DMC1_A07
DMC1_A02
DMC1_BA0
DMC1_A08
DMC1_CKE
Rev. PrG
|
Ball No.
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
E01
E02
E03
E04
E05
E06
E07
E08
E09
E10
E11
E12
E13
E14
E15
E16
E17
E18
E19
E20
E21
E22
E23
F01
F02
F03
F04
F05
F06
F07
F08
Page 158 of 168 |
Pin Name
DMC1_BA2
DMC1_CAS
DMC1_RAS
DMC1_A09
DMC1_A15
DMC1_A10
DMC1_A11
PC_14
PD_10
PD_09
DMC0_A04
DMC0_RAS
DMC0_BA1
DMC0_WE
DMC0_RZQ
GND
GND
GND
GND
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
DMC1_RZQ
PC_15
PD_08
PD_14
PD_11
DMC0_A01
DMC0_A06
DMC0_CAS
DMC0_A02
DMC0_A07
GND
VDD_INT
VDD_INT
June 2016
Ball No.
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
G01
G02
G03
G04
G05
G06
G07
G08
G09
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
H01
H02
H03
Pin Name
GND
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
GND
VDD_INT
VDD_INT
VDD_INT
PE_06
PD_02
PD_13
PD_12
DMC0_A13
DMC0_A09
DMC0_A03
DMC0_A11
VDD_INT
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_INT
PE_04
PE_13
PE_01
PE_00
DMC0_A14
DMC0_A12
DMC0_A05
Preliminary Technical Data
Ball No.
H04
H05
H06
H07
H08
H09
H10
H11
H12
H13
H14
H15
H16
H17
H18
H19
H20
H21
H22
H23
J01
J02
J03
J04
J05
J06
J07
J08
J09
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
J20
J21
J22
J23
K01
K02
K03
K04
Pin Name
DMC0_A00
VDD_INT
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_INT
SYS_CLKOUT
PE_12
PE_05
PE_02
DMC0_A15
DMC0_A10
DMC0_A08
PC_08
VDD_INT
VDD_DMC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
PD_03
PD_07
PF_14
PF_01
PE_07
DMC0_RESET
PC_11
PC_06
PC_09
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Ball No.
K05
K06
K07
K08
K09
K10
K11
K12
K13
K14
K15
K16
K17
K18
K19
K20
K21
K22
K23
L01
L02
L03
L04
L05
L06
L07
L08
L09
L10
L11
L12
L13
L14
L15
L16
L17
L18
L19
L20
L21
L22
L23
M01
M02
M03
M04
M05
Ball No.
M06
M07
M08
M09
M10
M11
M12
M13
M14
M15
M16
M17
M18
M19
M20
M21
M22
M23
N01
N02
N03
N04
N05
N06
N07
N08
N09
N10
N11
N12
N13
N14
N15
N16
N17
N18
N19
N20
N21
N22
N23
P01
P02
P03
P04
P05
P06
Pin Name
VDD_INT
VDD_DMC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PD_15
PF_11
PF_06
PE_10
PC_04
PC_12
PC_07
PC_10
VDD_INT
VDD_DMC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PE_03
PF_09
PE_09
PE_14
PC_01
PC_05
PC_02
SYS_FAULT
VDD_INT
Rev. PrG
|
Page 159 of 168 |
Pin Name
VDD_DMC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
PE_08
PE_11
PF_03
PF_00
PF_02
JTG_TMS
JTG_TRST
SYS_HWRST
PC_03
VDD_INT
VDD_EXT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PE_15
PF_04
PF_05
PF_07
JTG_TDO
JTG_TDI
SYS_FAULT
JTG_TCK
VDD_INT
VDD_EXT
June 2016
Ball No.
P07
P08
P09
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
R01
R02
R03
R04
R05
R06
R07
R08
R09
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23
T01
T02
T03
T04
T05
T06
T07
Pin Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
PF_10
PF_08
PF_15
PF_12
PG_00
SYS_XTAL1
SYS_BMODE1
SYS_BMODE2
SYS_BMODE0
VDD_INT
VDD_EXT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
PG_01
PG_05
PG_04
PF_13
SYS_CLKIN1
PB_15
GND
PB_14
VDD_INT
VDD_EXT
GND
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Ball No.
T08
T09
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
T20
T21
T22
T23
U01
U02
U03
U04
U05
U06
U07
U08
U09
U10
U11
U12
U13
U14
U15
U16
U17
U18
U19
U20
U21
U22
U23
V01
V02
V03
V04
V05
V06
V07
V08
V09
Pin Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
VDD_INT
DAI1_PIN03
PG_03
PG_02
DAI1_PIN01
SYS_XTAL0
SYS_RESOUT
PC_00
DAI0_PIN20
VDD_INT
VDD_EXT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VDD_EXT
DAI1_PIN08
DAI1_PIN07
DAI1_PIN04
DAI1_PIN05
DAI1_PIN02
SYS_CLKIN0
PB_13
DAI0_PIN19
DAI0_PIN12
VDD_INT
VDD_EXT
VDD_PCIE_RX
VDD_PCIE_TX
VDD_EXT
Ball No.
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
V21
V22
V23
W01
W02
W03
W04
W05
W06
W07
W08
W09
W10
W11
W12
W13
W14
W15
W16
W17
W18
W19
W20
W21
W22
W23
Y01
Y02
Y03
Y04
Y05
Y06
Y07
Y08
Y09
Y10
Y11
Pin Name
VDD_EXT
VDD_EXT
HADC0_VIN4
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_INT
DAI1_PIN16
DAI1_PIN06
DAI1_PIN12
DAI1_PIN09
PB_12
PB_09
DAI0_PIN18
DAI0_PIN11
VDD_INT
VDD_INT
VDD_PCIE
VDD_INT
VDD_INT
VDD_INT
VDD_INT
HADC0_VIN6
VDD_INT
VDD_RTC
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
DAI1_PIN20
DAI1_PIN11
DAI1_PIN10
DAI1_PIN13
PB_11
PB_10
DAI0_PIN17
DAI0_PIN08
DAI0_PIN05
DAI0_PIN10
USB0_ID
VDD_USB
USB0_VBC
TWI0_SCL
TWI2_SDA
Rev. PrG
|
Ball No.
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y20
Y21
Y22
Y23
AA01
AA02
AA03
AA04
AA05
AA06
AA07
AA08
AA09
AA10
AA11
AA12
AA13
AA14
AA15
AA16
AA17
AA18
AA19
AA20
AA21
AA22
AA23
AB01
AB02
AB03
AB04
AB05
AB06
AB07
AB08
AB09
AB10
AB11
AB12
AB13
Page 160 of 168 |
Pin Name
HADC0_VIN0
HADC0_VIN7
GND
PB_05
PA_14
PA_13
PA_12
PA_10
PA_00
DAI1_PIN14
DAI1_PIN17
DAI1_PIN15
PB_08
PB_07
DAI0_PIN16
DAI0_PIN07
DAI0_PIN06
DAI0_PIN01
PCIE0_REF
USB1_VBUS
USB0_VBUS
TWI1_SCL
TWI1_SDA
HADC0_VIN1
HADC0_VIN5
PB_06
PB_02
PB_04
PB_03
PB_00
PA_09
PA_05
PA_01
DAI1_PIN19
DAI1_PIN18
DAI0_PIN15
DAI0_PIN14
DAI0_PIN09
DAI0_PIN13
DAI0_PIN04
DAI0_PIN02
DAI0_PIN03
USB_XTAL
USB_CLKIN
TWI2_SCL
TWI0_SDA
HADC0_VREFN
HADC0_VIN2
June 2016
Preliminary Technical Data
Ball No.
AB14
AB15
AB16
AB17
AB18
AB19
AB20
AB21
AB22
AB23
AC01
AC02
AC03
AC04
AC05
AC06
AC07
AC08
AC09
AC10
AC11
AC12
AC13
AC14
AC15
AC16
AC17
AC18
AC19
AC20
AC21
AC22
AC23
Pin Name
HADC0_VIN3
RTC0_XTAL
MLB0_SIGN
MLB0_DATN
MLB0_CLKN
PA_15
PA_11
PA_06
PA_04
PA_02
GND
PCIE0_RXP
PCIE0_RXM
PCIE0_CLKM
PCIE0_CLKP
PCIE0_TXP
PCIE0_TXM
USB1_DM
USB1_DP
USB0_DP
USB0_DM
HADC0_VREFP
VDD_HADC
GND
RTC0_CLKIN
MLB0_SIGP
MLB0_DATP
MLB0_CLKP
PB_01
PA_07
PA_08
PA_03
GND
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ADSP-SC58x/ADSP-2158x 529-BALL BGA BALL ASSIGNMENTS (ALPHABETICAL BY PIN NAME)
Pin Name
DAI0_PIN01
DAI0_PIN02
DAI0_PIN03
DAI0_PIN04
DAI0_PIN05
DAI0_PIN06
DAI0_PIN07
DAI0_PIN08
DAI0_PIN09
DAI0_PIN10
DAI0_PIN11
DAI0_PIN12
DAI0_PIN13
DAI0_PIN14
DAI0_PIN15
DAI0_PIN16
DAI0_PIN17
DAI0_PIN18
DAI0_PIN19
DAI0_PIN20
DAI1_PIN01
DAI1_PIN02
DAI1_PIN03
DAI1_PIN04
DAI1_PIN05
DAI1_PIN06
DAI1_PIN07
DAI1_PIN08
DAI1_PIN09
DAI1_PIN10
DAI1_PIN11
DAI1_PIN12
DAI1_PIN13
DAI1_PIN14
DAI1_PIN15
DAI1_PIN16
DAI1_PIN17
DAI1_PIN18
DAI1_PIN19
DAI1_PIN20
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
Ball No.
AA06
AB06
AB07
AB05
Y05
AA05
AA04
Y04
AB03
Y06
W04
V04
AB04
AB02
AB01
AA03
Y03
W03
V03
U04
T23
U23
T20
U21
U22
V21
U20
U19
V23
W22
W21
V22
W23
Y21
Y23
V20
Y22
AA23
AA22
W20
H04
F01
F04
G03
E01
H03
F02
Pin Name
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_A14
DMC0_A15
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_RESET
DMC0_RZQ
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_VREF
DMC0_WE
DMC1_A00
DMC1_A01
Ball No.
F05
J03
G02
J02
G04
H02
G01
H01
J01
D03
E03
D04
F03
A04
C04
A03
C03
B10
A10
B09
A09
B08
A08
B06
B07
B05
A05
B04
B03
B02
C02
C01
D02
C05
A07
A06
D05
E02
K01
E05
D06
B01
A02
D01
E04
C08
C09
Rev. PrG
|
Pin Name
DMC1_A02
DMC1_A03
DMC1_A04
DMC1_A05
DMC1_A06
DMC1_A07
DMC1_A08
DMC1_A09
DMC1_A10
DMC1_A11
DMC1_A12
DMC1_A13
DMC1_A14
DMC1_A15
DMC1_BA0
DMC1_BA1
DMC1_BA2
DMC1_CAS
DMC1_CK
DMC1_CKE
DMC1_CK
DMC1_CS0
DMC1_DQ00
DMC1_DQ01
DMC1_DQ02
DMC1_DQ03
DMC1_DQ04
DMC1_DQ05
DMC1_DQ06
DMC1_DQ07
DMC1_DQ08
DMC1_DQ09
DMC1_DQ10
DMC1_DQ11
DMC1_DQ12
DMC1_DQ13
DMC1_DQ14
DMC1_DQ15
DMC1_LDM
DMC1_LDQS
DMC1_LDQS
DMC1_ODT
DMC1_RAS
DMC1_RESET
DMC1_RZQ
DMC1_UDM
DMC1_UDQS
Page 161 of 168 |
June 2016
Ball No.
D10
C07
C10
D07
C11
D09
D12
D17
D19
D20
C18
C19
C17
D18
D11
C12
D14
D15
A16
D13
A17
C14
A12
B11
B12
A11
B13
B14
B15
B16
B17
A18
B18
B19
B20
A21
B21
A22
C15
A13
A14
C13
D16
C06
E19
C16
A20
Pin Name
DMC1_UDQS
DMC1_VREF
DMC1_WE
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Ball No.
A19
A15
D08
A01
A23
AC01
AC14
AC23
E06
E07
E08
E09
F06
F09
F16
J07
J08
J09
J10
J11
J12
J13
J14
J15
J16
J17
K07
K08
K09
K10
K11
K12
K13
K14
K15
K16
K17
L07
L08
L09
L10
L11
L12
L13
L14
L15
L16
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Pin Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Ball No.
L17
M07
M08
M09
M10
M11
M12
M13
M14
M15
M16
M17
N07
N08
N09
N10
N11
N12
N13
N14
N15
N16
N17
P07
P08
P09
P10
P11
P12
P13
P14
P15
P16
P17
R07
R08
R09
R10
R11
R12
R13
R14
R15
R16
R17
T03
T07
T08
Pin Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
HADC0_VIN0
HADC0_VIN1
HADC0_VIN2
HADC0_VIN3
HADC0_VIN4
HADC0_VIN5
HADC0_VIN6
HADC0_VIN7
HADC0_VREFN
HADC0_VREFP
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
MLB0_CLKN
MLB0_CLKP
MLB0_DATN
MLB0_DATP
MLB0_SIGN
MLB0_SIGP
PA_00
PA_01
PA_02
PA_03
PA_04
PA_05
Ball No.
T09
T10
T11
T12
T13
T14
T15
T16
T17
U07
U08
U09
U10
U11
U12
U13
U14
U15
U16
U17
Y14
Y12
AA12
AB13
AB14
V12
AA13
W12
Y13
AB12
AC12
P04
P02
P01
N01
N02
AB18
AC18
AB17
AC17
AB16
AC16
Y20
AA21
AB23
AC22
AB22
AA20
Rev. PrG
|
Pin Name
PA_06
PA_07
PA_08
PA_09
PA_10
PA_11
PA_12
PA_13
PA_14
PA_15
PB_00
PB_01
PB_02
PB_03
PB_04
PB_05
PB_06
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
PB_15
PCIE0_CLKM
PCIE0_CLKP
PCIE0_REF
PCIE0_RXM
PCIE0_RXP
PCIE0_TXM
PCIE0_TXP
PC_00
PC_01
PC_02
PC_03
PC_04
PC_05
PC_06
PC_07
PC_08
PC_09
PC_10
PC_11
PC_12
PC_13
PC_14
Page 162 of 168 |
June 2016
Preliminary Technical Data
Ball No.
AB21
AC20
AC21
AA19
Y19
AB20
Y18
Y17
Y16
AB19
AA18
AC19
AA15
AA17
AA16
Y15
AA14
AA02
AA01
W02
Y02
Y01
W01
V02
T04
T02
AC04
AC05
AA07
AC03
AC02
AC07
AC06
U03
M01
M03
N04
L01
M02
K03
L03
J04
K04
L04
K02
L02
C20
D21
Pin Name
PC_15
PD_00
PD_01
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PD_10
PD_11
PD_12
PD_13
PD_14
PD_15
PE_00
PE_01
PE_02
PE_03
PE_04
PE_05
PE_06
PE_07
PE_08
PE_09
PE_10
PE_11
PE_12
PE_13
PE_14
PE_15
PF_00
PF_01
PF_02
PF_03
PF_04
PF_05
PF_06
PF_07
PF_08
PF_09
PF_10
PF_11
PF_12
PF_13
PF_14
Ball No.
E20
B22
C21
F21
J19
B23
C23
C22
J20
E21
D23
D22
E23
F23
F22
E22
K20
G23
G22
H23
L20
G20
H22
F20
J23
M19
L22
K23
M20
H21
G21
L23
N20
M22
J22
M23
M21
N21
N22
K22
N23
P20
L21
P19
K21
P22
R23
J21
Preliminary Technical Data
Pin Name
PF_15
PG_00
PG_01
PG_02
PG_03
PG_04
PG_05
RTC0_CLKIN
RTC0_XTAL
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN0
SYS_CLKIN1
SYS_CLKOUT
SYS_FAULT
SYS_FAULT
SYS_HWRST
SYS_RESOUT
SYS_XTAL0
SYS_XTAL1
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
TWI2_SCL
TWI2_SDA
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
USB1_DM
USB1_DP
USB1_VBUS
USB_CLKIN
USB_XTAL
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
Ball No.
P21
P23
R20
T22
T21
R22
R21
AC15
AB15
R04
R02
R03
V01
T01
H20
P03
M04
N03
U02
U01
R01
Y10
AB11
AA10
AA11
AB10
Y11
AC11
AC10
Y07
Y09
AA09
AC08
AC09
AA08
AB09
AB08
G06
G07
G08
G09
G10
G11
G12
G13
G14
G15
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Pin Name
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_HADC
VDD_INT
VDD_INT
Ball No.
G16
G17
G18
H06
H07
H08
H09
H10
H11
H12
H13
H14
H15
H16
H17
H18
J06
K06
L06
M06
J18
K18
L18
M18
N06
N18
P06
P18
R06
R18
T06
T18
U06
U18
V06
V09
V10
V11
V13
V14
V15
V16
V17
V18
AC13
E10
E11
Rev. PrG
|
Pin Name
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
Page 163 of 168 |
June 2016
Ball No.
E12
E13
E14
E15
E16
E17
E18
F07
F08
F10
F11
F12
F13
F14
F15
F17
F18
F19
G05
G19
H05
H19
J05
K05
K19
L05
L19
M05
N05
N19
P05
R05
R19
T05
T19
U05
V05
V19
W05
W06
W08
W09
W10
W11
W13
W15
W16
Pin Name
VDD_INT
VDD_INT
VDD_INT
VDD_PCIE
VDD_PCIE_RX
VDD_PCIE_TX
VDD_RTC
VDD_USB
Ball No.
W17
W18
W19
W07
V07
V08
W14
Y08
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
CONFIGURATION OF THE 529-BALL CSP_BGA
Figure 80 shows an overview of signal placement on the 529-ball CSP_BGA.
TOP VIEW
A1 BALL
CORNER
1
2
3
4
5
6
7
8
V
C
T
W
P
10 11 12 13 14 15 16 17 18 19 20 21 22 23
9
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
Y
R
U
AA
AB
AC
H
23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
A1 BALL
CORNER
1
A
B
C
D
E
F
GND
G
I/O SIGNALS
H
VDD_EXT
J
VDD_INT
K
L
VDD_DDR
U
VDD_USB
R
VDD_RTC
P
VDD_PCIE
H
VDD_HADC
T
C
VDD_CORE_PCIRX
U
T
VDD_CORE_PCITX
M
N
P
R
T
R
C
V
P
W
Y
U
AA
AB
H
AC
BOTTOM VIEW
Figure 80. 529-Ball CSP_BGA Configuration
Rev. PrG
|
Page 164 of 168 |
June 2016
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
OUTLINE DIMENSIONS
Dimensions for the 19 mm × 19 mm 349-ball CSP_BGA package in Figure 81 are shown in millimeters.
A1 BALL
CORNER
19.10
19.00 SQ
18.90
A1 BALL
CORNER
22 20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
A
C
G
16.80
BSC SQ
J
F
H
K
L
M
N
0.80
BSC
B
D
E
P
R
T
U
W
AA
TOP VIEW
1.50
1.36
1.21
1.10 REF
V
Y
AB
BOTTOM VIEW
DETAIL A
DETAIL A
1.11
1.01
0.91
0.35 NOM
0.30 MIN
SEATING
PLANE
0.50
COPLANARITY
0.20
0.45
0.40
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MO-275-PPAB-2.
Figure 81. 349-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-349-1)
Dimensions shown in millimeters
Rev. PrG
|
Page 165 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
Preliminary Technical Data
Dimensions for the 19 mm × 19 mm 529-ball CSP_BGA package in Figure 82 are shown in millimeters.
A1 BALL
CORNER
19.10
19.00 SQ
18.90
A1 BALL
CORNER
22 20 18 16 14 12 10 8 6 4 2
23 21 19 17 15 13 11 9 7 5 3 1
A
C
17.60
REF SQ
0.80
BSC
TOP VIEW
1.50
1.36
1.21
B
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
BOTTOM VIEW
0.70 REF
DETAIL A
DETAIL A
1.11
1.01
0.91
0.39
0.35
0.30
SEATING
PLANE
0.50
COPLANARITY
0.2
0.45
0.40
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MO-275-RRAB-2.
Figure 82. 529-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-529-1)
Dimensions shown in millimeters
SURFACE-MOUNT DESIGN
Table 102 is provided as an aid to PCB design. For industry-standard design recommendations, refer to IPC-7351, Generic Requirements
for Surface-Mount Design and Land Pattern Standard.
Table 102. CSP_BGA Data for Use with Surface-Mount Design
Package
Ball Attach Type
Solder Mask Defined
Solder Mask Defined
Package
BC-349-1
BC-529-1
Rev. PrG
|
Page 166 of 168 |
June 2016
Package
Solder Mask Opening
0.4 mm Diameter
0.4 mm Diameter
Package
Ball Pad Size
0.5 mm Diameter
0.5 mm Diameter
Preliminary Technical Data
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
ORDERING GUIDE
Model1
ADSP-SC584-ENG
ADSP-SC589-ENG
ADSP-21583-ENG
Processor Instruction
Rate (Max)
450 MHz
450 MHz
450 MHz
Temperature
Range2, 3
NA
NA
NA
Package Description
349-Ball Chip Scale Package Ball Grid Array
529-Ball Chip Scale Package Ball Grid Array
349-Ball Chip Scale Package Ball Grid Array
1
Package
Option
BC-349-1
BC-529-1
BC-349-1
Z =RoHS compliant part.
Referenced temperature is ambient temperature. The ambient temperature is not a specification. Please see Operating Conditions on Page 80 for the junction temperature
(TJ) specification which is the only temperature specification.
3
These are pre production parts. See ENG-Grade agreement for details.
2
Rev. PrG
|
Page 167 of 168 |
June 2016
ADSP-SC582/583/584/587/589/ADSP-21583/584/587
©2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR13317-0-6/16(PrG)
Rev. PrG
|
Page 168 of 168 |
June 2016
Preliminary Technical Data