ADSP-CM408F EZ-KIT Lite Evaluation System Manual (Rev. 1.1) PDF

ADSP-CM408F EZ-KIT Lite®
Evaluation System Manual
Revision 1.1, September 2013
Part Number
82-000341-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Copyright Information
©2013 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, EngineerZone, EZ-Board, and EZ-KIT Lite are
registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The ADSP-CM408F EZ-KIT Lite is designed to be used solely in a laboratory environment. The board is not intended for use as a consumer end
product or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The ADSP-CM408F EZ-KIT Lite is in the process of being certified to
comply with the essential requirements of the European EMC directive
2004/108/EC and therefore carries the “CE” mark.
The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge)
sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation or loss of
functionality. Store unused EZ-KIT Lite boards in the protective shipping
package.
CONTENTS
PREFACE
Product Overview ............................................................................ x
Purpose of This Manual ................................................................. xiv
Intended Audience ......................................................................... xiv
Manual Contents ............................................................................ xv
What’s New in This Manual ............................................................ xv
Technical Support .......................................................................... xvi
Supported Processors ...................................................................... xvi
Supported Tools ............................................................................ xvii
Product Information ..................................................................... xvii
Analog Devices Web Site ......................................................... xvii
EngineerZone ......................................................................... xviii
Notation Conventions .................................................................. xviii
USING ADSP-CM408F EZ-KIT LITE
Package Contents .......................................................................... 1-2
ADSP-CM408F EZ-Board ............................................................ 1-3
Default Configuration ................................................................... 1-3
IAR Embedded WorkBench and Board Installation ........................ 1-5
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
v
Contents
IAR Embedded WorkBench Session Startup .................................. 1-6
SRAM Memory (U2) .................................................................... 1-8
SPI Flash ...................................................................................... 1-8
Analog Interface ........................................................................... 1-8
UART0 Interface (RS-232) ........................................................... 1-9
UART1 Interface (RS-485) ......................................................... 1-10
CAN0 Interface .......................................................................... 1-11
CAN1 Interface .......................................................................... 1-11
USB OTG FS Interface ............................................................... 1-12
Ethernet Interface ....................................................................... 1-12
Debug Interface .......................................................................... 1-13
Serial Liquid Crystal Display Module Interface ............................ 1-13
Power-On-Self Test ..................................................................... 1-14
Expansion Interface .................................................................... 1-14
Power Architecture ..................................................................... 1-15
Power Measurements .................................................................. 1-15
Example Programs ...................................................................... 1-16
Reference Design Information ..................................................... 1-16
vi
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Contents
ADSP-CM408F EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Software-Controlled Switches (SoftConfig) .................................... 2-3
Overview of SoftConfig ........................................................... 2-3
SoftConfig on the ADSP-CM408F EZ-KIT LITE ................... 2-7
Programming SoftConfig Switches ........................................... 2-8
Push Buttons and Switches .......................................................... 2-15
Boot Mode Select Switch (SW1) ............................................ 2-16
Reset Push Button (SW2) ...................................................... 2-16
GPIO Push Buttons (SW4-5) ................................................ 2-16
Wake Push Button (SW3) ...................................................... 2-17
Jumpers ...................................................................................... 2-17
VREF1 External Source Jumper (JP1) .................................... 2-18
Power Select Jumper (JP2) ..................................................... 2-18
Buffer Input Select Jumper (JP3) ........................................... 2-18
VREF0 External Source Jumper (JP4) .................................... 2-19
Power Jumpers (P4-7) ............................................................ 2-19
LEDs .......................................................................................... 2-20
GPIO LEDs (LED1–4) ......................................................... 2-21
Reset LED (LED5) ................................................................ 2-21
Ethernet Speed LED (LED6) ................................................. 2-21
Power LED (LED7) ............................................................... 2-22
SYS_FAULT LED (LED8) ..................................................... 2-22
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
vii
Contents
Connectors ................................................................................. 2-23
Ethernet Connector (J1) ....................................................... 2-24
RS-485 Connector (J2) ......................................................... 2-24
DCE UART Connector (J3) .................................................. 2-24
Asynch or Memory Connector (J4) ........................................ 2-24
Character Display Connector (J5) ......................................... 2-25
PWM Connector (J6) ........................................................... 2-25
CAN0 Connector (J7) ........................................................... 2-25
CAN1 Connector (J8) ........................................................... 2-26
Analog Connector (J9) .......................................................... 2-26
JTAG/SWD Connector (P1) ................................................. 2-26
TRACE and JTAG/SWD/SWV Connector (P2) .................... 2-26
USB Connector (P3) ............................................................. 2-27
IEEE 1588 Connector (P8) ................................................... 2-27
Power Connector (P9) ........................................................... 2-27
VREF Buffered Connector (P10) ........................................... 2-27
ADSP-CM408F EZ-KIT LITE BILL OF MATERIALS
ADSP-CM408F EZ-KIT LITE SCHEMATIC
INDEX
viii
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
PREFACE
Thank you for purchasing the ADSP-CM408F EZ-KIT Lite®, Analog
Devices, Inc. low-cost evaluation system for the ADSP-CM408F
mixed-signal control processor.
The ADSP-CM408F processor is based on the ARM® Cortex®-M4 processor core and is designed for motor control and industrial applications.
The EZ-KIT Lite is shipped with all of the necessary hardware—you can
start the evaluation immediately. The package contains the standalone
evaluation board, CE-approved power supply, and USB cable. The
EZ-KIT Lite version ships with the J-Link Lite ARM, while the
EZ-Board® version requires the customer to provide an emulator.
Two expansion connectors (analog interface and PWM/digital interface)
are provided for connecting boards that incorporate motors. Another
expansion connector is provided for connecting an Anybus board and/or a
memory/FPGA extender card.
Traditional mechanical switches for changing the board’s factory setup
have been removed in favor of I2C controlled software switches. The only
remaining mechanical switches are the boot mode switch and push
buttons.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ix
Product Overview
The evaluation board is designed to be used in conjunction with the IAR
Embedded Workbench development tools to test capabilities of the
ADSP-CM408F processors. The development environment aids advanced
application code development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory
• Read and write core and peripheral registers
Product Overview
The board features:
• Analog Devices ADSP-CM408F processor
• 176-pin LQFP package
• 30 MHz CLKIN core oscillator
• SRAM memory (SMC0) chip
• 256K x 16-bit (4M bit)
• Cypress CY7C1041DV33
• Ethernet PHY (ETH0)
• 10/100 Mb/s
• Texas Instruments DP83848C
x
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Preface
• Universal Asynchronous Receiver/Transmitter (UART0)
• Analog Devices ADM3252E RS-232 line transceiver
• DB9 female connector
• Universal Asynchronous Receiver/Transmitter (UART1)
• Analog Devices ADM2682E RS-485 line transceiver
• DB9 female connector
• Controller Area Network (CAN) interfaces
• CAN0—Analog Devices ADM3053 transceiver and RJ11
connector
• CAN1—Analog Devices ADM3053 transceiver and RJ11
connector
• USB interface
• Molex 56579-0576 connector
• Display
• New Haven NHD-0220D3Z-FL-GBW
• 2 x 20 character
• 2-wire interface (TWI) control
• RESET controller
• Analog Devices ADM708 microprocessor supervisory
circuits
• Debug (JTAG/SWD/SWV/TRACE) interface
• JTAG/SWD 20-pin 0.1” header for use with IAR emulators
• Trace/JTAG/SWD/SWV 20-pin 0.05” header
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
xi
Product Overview
• LEDs
• Eight LEDs: one power (green), one board reset (red), one
Ethernet speed (green), one SYS_FAULT (red), and four
general-purpose (amber)
• Push buttons
• Four push buttons: one reset, one wake, two IRQ/Flag
• Asynchronous connector
• 180-pin Samtec (QSH-090-01-F-D-A) 0.5 mm spacing
• SMC0 address, data, and control
• CLKOUT
• SPI1
• UART2
• TWI0
• GPIOs
• RESET
• GND/3.3V/5V output
• Pulse-width modulation (PWM) connector
• 180-pin Samtec (QSH-090-01-F-D-A) 0.5 mm spacing
• PWM0—PWM2
• SINC0
• SPI1
• SPT0
• TWI0
xii
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Preface
• TMR0
• CNT0—CNT3
• GPIO
• RESET
• GND/3.3V/5V output
• 5V output
• Analog connector interface
• 120-pin Samtec (QSH-060-01-F-D-A) 0.5 mm spacing
• ADC0
• AGND/GND/VREF/5VOUT
• ADR441 voltage reference (VREF)
• ADA4899 buffer—0.1” header for reference
• 1588 connector
• 0.1” header 6-pin
• External power supply
• CE compliant
• 5V @ 3.6 Amps
• Ability to power from the PWM connector
• Other features
• 0.05-ohm resistors for processor current measurement
For information about the hardware components of the EZ-KIT Lite,
refer to ADSP-CM408F EZ-KIT Lite Bill Of Materials.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
xiii
Purpose of This Manual
Purpose of This Manual
The ADSP-CM408F EZ-KIT Lite Evaluation System Manual provides
instructions for installing the product hardware (board). The text
describes operation and configuration of the board components and provides guidelines for running your own code on the ADSP-CM408F
EZ-KIT Lite. Finally, a schematic and a bill of materials are provided for
reference.
Intended Audience
The primary audience for this manual is a programmer who is familiar
with an ARM Cortex-M4-based processor core.
The ADSP-CM40x family of mixed-signal control processors is based on
the ARM Cortex-M4 processor core with floating-point unit and integrated SRAM memory, flash memory, accelerators, and peripherals.
The applicable documentation for programming the ARM Cortex-M4
processor core includes:
• Cortex-M4 Devices Generic User Guide
• CoreSight ETM-M4 Technical Reference Manual
• Cortex-M4 Technical Reference Manual
For additional information on this Analog Devices processor, see the
ADSP-CM40x Mixed-Signal Control Processor Hardware Reference. This
document describes the ARM Cortex-M4 processor core and memory
architecture used on the ADSP-CM40x processor, but does not provide
detailed programming information for the ARM core.
xiv
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Preface
For more information about programming the ARM core, visit the ARM
Information Center:
http://infocenter.arm.com/help/
Manual Contents
The manual consists of:
• Chapter 1, Using ADSP-CM408F EZ-KIT Lite
Describes EZ-KIT Lite functionality from a programmer’s perspective and provides a simplified memory map of the processor.
• Chapter 2, ADSP-CM408F EZ-KIT Lite Hardware Reference
Provides information about the EZ-KIT Lite hardware
components.
• Appendix A, ADSP-CM408F EZ-KIT Lite Bill Of Materials
Provides a list of hardware components used to manufacture the
EZ-KIT Lite board.
• Appendix B, ADSP-CM408F EZ-KIT Lite Schematic
Lists the resources for board-level debugging.
What’s New in This Manual
This is Revision 1.1 of the ADSP-CM408F EZ-KIT Lite Evaluation System
Manual. Changes from Revision 1.0 include an updated Bill of Materials
and an updated schematic.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
xv
Technical Support
Technical Support
You can reach Analog Devices processors and DSP technical support in
the following ways:
• Post your questions in the processors and DSP support community
at EngineerZone®:
http://ez.analog.com/community/dsp
• Submit your questions to technical support directly at:
http://www.analog.com/support
• E-mail your questions about processors and processor applications
to:
[email protected] or
[email protected] (Greater China support)
• In the USA only, call 1-800-ANALOGD (1-800-262-5643)
• Contact your Analog Devices sales office or authorized distributor.
Locate one at:
www.analog.com/adi-sales
• Send questions by mail to:
Processors and DSP Technical Support
Analog Devices, Inc.
Three Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Processors
This evaluation system supports Analog Devices ADSP-CM408F
processors.
xvi
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Preface
Supported Tools
Information on supported tools for the ADSP-CM408F EZ-KIT Lite and
the ADSP-CM40x family of mixed-signal control processors is available
at:
http://www.analog.com/CM408FEZKit
Product Information
Product information can be obtained from the Analog Devices Web site
and the online help system.
Analog Devices Web Site
The Analog Devices Web site, www.analog.com, provides information
about a broad range of products—analog integrated circuits, amplifiers,
converters, and digital signal processors.
To access a complete technical library for each processor family, go to
http://www.analog.com/processors/technical_library. The manuals
selection opens a list of current manuals related to the product as well as a
link to the previous revisions of the manuals. When locating your manual
title, note a possible errata check mark next to the title that leads to the
current correction report against the manual.
Also note, myAnalog.com is a free feature of the Analog Devices Web site
that allows customization of a Web page to display only the latest
information about products you are interested in. You can choose to
receive weekly e-mail notifications containing updates to the Web pages
that meet your interests, including documentation errata against all manuals. myAnalog.com provides access to books, application notes, data sheets,
code examples, and more.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
xvii
Notation Conventions
Visit myAnalog.com (found on the Analog Devices home page) to sign up.
If you are a registered user, just log on. Your user name is your e-mail
address.
EngineerZone
EngineerZone is a technical support forum from Analog Devices. It allows
you direct access to ADI technical support engineers. You can search
FAQs and technical information to get quick answers to your embedded
processing and DSP design questions.
Use EngineerZone to connect with other DSP developers who face similar
design challenges. You can also use this open forum to share knowledge
and collaborate with the ADI support team and your peers. Visit
http://ez.analog.com to sign up.
Notation Conventions
Text conventions used in this manual are identified and described as
follows.
xviii
Example
Description
File > Close
Titles in reference sections indicate the location of an item within the
CCES environment’s menu system (for example, the Close command
appears on the File menu).
{this | that}
Alternative required items in syntax descriptions appear within curly
brackets and separated by vertical bars; read the example as this or
that. One or the other is required.
[this | that]
Optional items in syntax descriptions appear within brackets and separated by vertical bars; read the example as an optional this or that.
[this,…]
Optional item lists in syntax descriptions appear within brackets delimited by commas and terminated with an ellipse; read the example as an
optional comma-separated list of this.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Preface
Example
Description
.SECTION
Commands, directives, keywords, and feature names are in text with
letter gothic font.
filename
Non-keyword placeholders appear in text with italic style format.

Note: For correct operation, ...
A Note provides supplementary information on a related topic. In the
online version of this book, the word Note appears instead of this
symbol.

Caution: Incorrect device operation may result if ...
Caution: Device damage may result if ...
A Caution identifies conditions or inappropriate usage of the product
that could lead to undesirable results or product damage. In the online
version of this book, the word Caution appears instead of this symbol.

Warning: Injury to device users may result if ...
A Warning identifies conditions or inappropriate usage of the product
that could lead to conditions that are potentially hazardous for the
devices users. In the online version of this book, the word Warning
appears instead of this symbol.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
xix
Notation Conventions
xx
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1 USING ADSP-CM408F EZ-KIT
LITE
This chapter provides information to assist you with development of programs for the ADSP-CM408F EZ-KIT Lite evaluation system.
The following topics are covered.
• Package Contents
• ADSP-CM408F EZ-Board
• Default Configuration
• IAR Embedded WorkBench and Board Installation
• IAR Embedded WorkBench Session Startup
• SRAM Memory (U2)
• SPI Flash
• Analog Interface
• UART0 Interface (RS-232)
• UART1 Interface (RS-485)
• CAN0 Interface
• CAN1 Interface
• USB OTG FS Interface
• Ethernet Interface
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-1
Package Contents
• Debug Interface
• Serial Liquid Crystal Display Module Interface
• Power-On-Self Test
• Expansion Interface
• Power Architecture
• Power Measurements
• Example Programs
• Reference Design Information
Package Contents
Your ADSP-CM408F EZ-KIT Lite package contains the following items.
• ADSP-CM408F EZ-KIT Lite board
• Universal 5V DC power
• USB 2.0 cable
• J-Link Lite ARM (only in the EZ-KIT Lite version)
Contact the vendor where you purchased your EZ-KIT Lite or contact
Analog Devices, Inc. if any item is missing.
1-2
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
ADSP-CM408F EZ-Board
The ADSP-CM408F EZ-KIT Lite is shipped with the J-Link Lite ARM
debugger. When the product is not shipped with the debugger, it is
referred to as the ADSP-CM408F EZ-Board.

The EZ-Board requires a third party emulator.
Default Configuration
The ADSP-CM408F EZ-KIT Lite board is designed to run as a standalone unit.
When removing the EZ-KIT Lite board from the package, handle the
board carefully to avoid the discharge of static electricity, which can damage some components.
The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge)
sensitive devices. Electrostatic charges readily accumulate on the human body
and equipment and can discharge without detection. Permanent damage may
occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused EZ-KIT Lite boards in the protective shipping package.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-3
Default Configuration
Figure 1-1 shows the default jumper settings, connector locations, and
LEDs used in installation. Confirm that your board is in the default configuration before using the board.
Figure 1-1. Default EZ-KIT Lite Hardware Setup
1-4
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
IAR Embedded WorkBench and Board
Installation
For information about the IAR Embedded WorkBench® product and
software download, go to:
http://www.iar.com/en/Products/IAR-Embedded-Workbench
The ADSP-CM408F EZ-KIT Lite software, based on the IAR Embedded
WorkBench, can be found at:
http://www.analog.com/CM408FEZKit
Follow these instructions to ensure correct operation of the product software and hardware.
Step 1: Connect the EZ-KIT Lite board to a personal computer (PC) running IAR Embedded WorkBench using a J-Link/J-Trace emulator.
1. Plug one side of the USB cable into the USB connector of the emulator. Plug the other side into a USB port of the PC running IAR
Embedded WorkBench.
2. Attach the emulator to the header connector, P1 or P2, on the
EZ-KIT Lite board.
Step 2: Attach the provided cord and appropriate plug to the 5V power
adaptor.
1. Plug the jack-end of the power adaptor into the power connector
P9 (labeled 5V) on the EZ-KIT Lite board.
2. Plug the other side of the power adaptor into a power outlet. The
power LED (labeled LED7) is lit green when power is applied to the
board.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-5
IAR Embedded WorkBench Session Startup
IAR Embedded WorkBench Session
Startup
It is assumed that the IAR Embedded WorkBench software is installed
and running on your PC.
1. Navigate to the IAR Embedded WorkBench environment via the
Start menu.
Note that IAR Embedded WorkBench is not connected to the target board.
2. Choose File > Open >Workspace to open a workspace for the project to download and debug.
3. Choose Project > Options.
The General Options, Target page appears.
4. In Processor variant, ensure Device is AnalogDevices
ADSP-CM40z-X_Y, where X is the SRAM size in KB and Y is the
internal flash size in KB of the part on the target board.
On the Analog Devices ADSP-CM408F EZ-KIT Lite, SRAM size
is 384 KB, and internal flash size is 2048 KB.
1-6
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
5. Choose Debugger in the Category pane.
The Debugger, Setup options page appears.
a. In Driver, choose J-Link/J-Trace as the emulator to be used
to debug the target board.
b. Click the Download tab. The Debugger, Download options
page appears.
c. Ensure Use flash loader(s) is enabled. Note that other
download settings are optional.
6. Choose Debugger > J-Link/J-Trace in the Category pane.
The emulator Setup options page appears.
a. On the Setup page,
• In Reset, select Connect during reset from the drop-down
list.
• In JTAG/SWD speed, select Auto.
• (Optional) In Clock setup, change the default values.
b. On the Connection page,
• In Communication, select USB and Device 0.
• In Interface, select JTAG or SWD.
7. Click OK to save the emulator settings.
8. Choose Project > Debug and Download to download the project
and start debugging.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-7
SRAM Memory (U2)
SRAM Memory (U2)
The ADSP-CM408F processor is connected to a 4 Mb Cypress asynchronous SRAM device (CY7C1041DV33). The upper and lower halves of the
16-bit-wide data bus are connected to SoftConfig circuitry, which disconnects the expansion interface. The connection to the expansion interface is
OFF by default.
Byte-enable signals ABE0 and ABE1 on the processor’s pins PE_12 and PE_13
(respectively) are not connected by default; can be connected via
SoftConfig.
For more information, refer to the SRAM example in the POST, which is
included in the ADSP-CM40x Enablement Software.
SPI Flash
The EZ-KIT Lite ships with an internal 4 MB SPI flash, connected via the
SPI2 interface, which is used for booting and scratchpad space. Refer to
the ADSP-CM40x Mixed-Signal Control Processor Hardware Reference for
more information about the internal SPI flash.
For more information, refer to the SPI flash example in the POST, which
is included in the ADSP-CM40x Enablement Software.
Analog Interface
The ADSP-CM408F processor provides two 16-bit ADCs with 8 inputs
each, ADC0 and ADC1. The ADC signals are connected to the Analog expansion connector (J9). Refer to ADSP-CM408F EZ-KIT Lite Schematic for
more information.
Voltage reference for the ADC channels can be supplied internally from
the processor or externally by ADR441 ICs. U5 is the VREF0 supply
1-8
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
external source, and U47 is its VREF1 equivalent. To select the external
source for either supply, place a jumper on JP1 or JP4. Refer to
ADSP-CM408F EZ-KIT Lite Schematic for more information.
A buffered version of the voltage reference is available on J9 via a unity
gain buffer ADA4889 (U33). By default, the internal VREF0 source is
selected as the input to the buffer (JP3 positions 1 and 2). If the external
voltage reference is desired, change the jumper to JP3 positions 2 and 3.
Voltage references for the analog inputs are configurable; refer to Jumpers
for more information.
UART0 Interface (RS-232)
The ADSP-CM408F processor has three built-in universal asynchronous
transmitters (UARTs). UART0 is connected to a RS-232 line transmitter.
UART0 has full RS-232 functionality via the Analog Devices ADM3252E
isolated line driver and receiver (U36).
EZ-KIT Lite voltage isolation components are not intended
 The
for protecting external products. The isolated ICs are used to showcase Analog Devices product portfolio only. Adequate voltage
isolation of any external devices/boards is the user responsibility.
Pin PC_02/UART0_TX/TRACE_D03/SPI0_RDY of the processor is connected to
the ADM3315 device directly and used for UART transmit.
Pin PC_01/UART0_RX/SMC0_A05/TM0_ACI5 is connected through SoftConfig
by default and used for UART receive. (This can be changed using
SoftConfig.)
By default, the UART0 CTS signal is not connected, and the UART0 RTS signal is connected to RS-232. Both connections can be changed through
SoftConfig.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-9
UART1 Interface (RS-485)
The SoftConfig switches also allow the loopback of CTS and RTS. The
UART0 CTS can be added as an input to the reset circuit through SoftConfig. Refer to Software-Controlled Switches (SoftConfig) for more
information.
For more information, refer to the UART0 example in the POST, which
is included in the ADSP-CM40x Enablement Software. Note that the
loopback of TX and RX data is done through an external connector.
UART1 Interface (RS-485)
is connected to a RS-485 line transmitter. UART1 has full RS-485
functionality via the Analog Devices ADM2682E isolated line driver and
receiver (U39) that can transmit at 16 Mbps.
UART1
The EZ-KIT Lite is designed to be the end node in a network; therefore, it
has a termination resistor (R44) installed with a value of 120 ohms. If the
board is intended to be a middle node in the network, the resistor can be
removed.
EZ-KIT Lite voltage isolation components are not intended
 The
for protecting external products. The isolated ICs are used to showcase Analog Devices product portfolio only. Adequate voltage
isolation of any external devices/boards is the user responsibility.
The UART1 transmit and receive signals are connected to the RS-485 transmitter directly from the processor. The ADM2682E device has driver
enable and receiver enable signals, controlled by SoftConfig. The driver
enable and receiver enable signals are disabled by default. Refer to Software-Controlled Switches (SoftConfig) for more information.
For more information, refer to the UART1 example in the POST, which
is included in the ADSP-CM40x Enablement Software. Note that the
loopback of the differential signals is done through an external connector.
1-10
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
CAN0 Interface
The Controller Area Network 0 (CAN0) interface of the EZ-KIT Lite is
connected to the Analog Devices ADM3053 isolated CAN transceiver.
The transceiver is attached to the CAN0 port of the ADSP-CM408F processor via an RJ-11 connector (J7). See CAN0 Connector (J7).
EZ-KIT Lite voltage isolation components are not intended
 The
for protecting external products. The isolated ICs are used to showcase Analog Devices product portfolio only. Adequate voltage
isolation of any external devices/boards is the user responsibility.
The CAN0 transmit and receive signals are connected through the SoftConfig switches and enabled by default. See Software-Controlled Switches
(SoftConfig).
For more information, refer to the CAN0 example in the POST, which is
included in the ADSP-CM40x Enablement Software.
CAN1 Interface
The Controller Area Network 1 (CAN1) interface of the EZ-KIT Lite is
connected to the Analog Devices ADM3053 isolated CAN transceiver.
The transceiver is attached to the CAN1 port of the ADSP-CM408F processor via an RJ-11 connector (J8). See CAN1 Connector (J8).
EZ-KIT Lite voltage isolation components are not intended
 The
for protecting external products. The isolated ICs are used to showcase Analog Devices product portfolio only. Adequate voltage
isolation of any external devices/boards is the user responsibility.
The CAN1 transmit and receive signals are connected through the SoftConfig switches and enabled by default. See Software-Controlled Switches
(SoftConfig).
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-11
USB OTG FS Interface
For more information, refer to the CAN1 example in the POST, which is
included in the ADSP-CM40x Enablement Software.
USB OTG FS Interface
The ADSP-CM408F processor has an integrated USB PHY; the EZ-KIT
Lite provides a mini AB connector. The board only supports USB full
speed mode.
The board allows 5V at 500 mA to a peripheral device by enabling the
FET switch (U44). The USB controller controls the FET switch through
the USB_VBC signal.
To learn about the processor’s device and host modes, refer to the USB
example in the POST, which is included in the ADSP-CM40x Enablement Software. For more information, refer to the ADSP-CM40x
Mixed-Signal Control Processor Hardware Reference.
Ethernet Interface
The ADSP-CM408F processor features a Reduced Media Independent
Interface (RMII), which connects to an external Ethernet PHY device
(ETH0). The EZ-KIT Lite provides a Texas Instruments DP83848C,
Auto-MDIX, fully-compliant PHY with IEEE 802.2/802.2u standards.
The PHY supports 10BASE-T and 100BASE-TX operations and is connected to a standard RJ-45 connector (J1). The IEEE 1588 time stamping
signals can be probed on connector P8. For more information, see Ethernet Connector (J1) and IEEE 1588 Connector (P8). Link and activity
LEDs are integrated into the RJ45 connector. The speed indication LED
(LED6) is located next to the RJ45 connector. See Ethernet Speed LED
(LED6).
1-12
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
The MAC address is printed on the back of the EZ-KIT Lite board; the
address must be set in software to use the Ethernet.
The Ethernet PHY device is disabled via SoftConfig. Refer to Software-Controlled Switches (SoftConfig) for more information.
For more information, refer to the ethernet example in the POST, which
is included in the ADSP-CM40x Enablement Software.
Debug Interface
The EZ-KIT Lite provides a JTAG/SWD/SWV connection via a connector (P1), which is a 0.1” header. A 4-bit trace connection also is available
via a connector (P2). See JTAG/SWD Connector (P1) and TRACE and
JTAG/SWD/SWV Connector (P2) for more information.
Serial Liquid Crystal Display Module
Interface
Connector J5 mates with the Newhaven Display International
NHD-0220D3Z-FL-GBW-V3, a 2-line by 20-character display with a
yellow/green backlight.
The display is written using the TWI interface. The TWI address of the
display is 0x50. The maximum clock rate for the display is 100 kHz. The
display can be removed if the frequency limitation poses a problem.
For more information, refer to the serial liquid crystal display example in
the POST, which is included in the ADSP-CM40x Enablement Software.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-13
Power-On-Self Test
Power-On-Self Test
The Power-On-Self-Test Program (POST) tests all EZ-KIT Lite peripherals and validates functionality as well as connectivity to the processor.
Once assembled, each EZ-KIT Lite is fully tested for an extended period
of time with POST. All EZ-KIT Lite boards are shipped with POST preloaded into flash memory. The POST is executed by resetting the board
and pressing the proper push button(s). The POST also can be used as a
reference for a custom software design or hardware troubleshooting.
Note that the source code for the POST program is included in the
ADSP-CM40x Enablement Software along with the readme.txt file that
describes how the board is configured to run POST.
Expansion Interface
The expansion interface allows a custom-design daughter board to be
tested across various hardware platforms that have the same expansion
interface.
The expansion interface implemented on the ADSP-CM408F EZ-KIT
Lite consists of three connectors: Asynch or Memory Connector (J4),
PWM Connector (J6), and Analog Connector (J9). The connectors contain a majority of the processor’s signals. For pinout information, go to
ADSP-CM408F EZ-KIT Lite Schematic.
Limits to current and interface speed must be taken into consideration
when using the expansion interface. Current for extenders connected to J4
or J6 can be sourced from the EZ-KIT Lite; therefore, the current should
be limited to 250 mA for 5V, and 200 mA from the 3.3V planes. If more
current is required, a separate power connector and a regulator must be
designed on the daughter card. Additional circuitry implemented on
1-14
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Using ADSP-CM408F EZ-KIT Lite
extender cards can add extra loading to signals, decreasing their maximum
effective speed.
Devices does not support and is not responsible for the
 Analog
effects of additional circuitry.
Power Architecture
The ADSP-CM408F EZ-KIT Lite has two primary voltage domains: 3.3V
and 1.2V. The main input is a 5V wall adaptor. The 5V source can be
selected via JP2 to input from the PWM connector (J6) as an alternative
to the wall power adaptor. Refer to PWM Connector (J6) and Power
Select Jumper (JP2) for details.
The Analog Devices ADP2119 controller provides 3.3V for the VDD_EXT
signal and the 3.3V power requirements of the board. The VDD_INT signal
is delivered through either Analog Devices regulator ADP2119 (VR1) or a
PNP transistor (Q1).
A FET switch (U44) controls the 5V to the USB devices over the USB_VBUS
signal.
Power Measurements
Locations are provided for measuring the current draw from various power
planes. Precision 0.05 ohm shunt resistors are available on the VDD_EXT,
VDD_INT, USB_VBUS, and 3.3V and voltage domains. For current draw, the
jumper is removed, voltage across the resistor can be measured using an
oscilloscope, and the value of the resistor can be measured using a precision multi-meter. Once voltage and resistance are measured, the current
can be calculated by dividing the voltage by the resistance. For the highest
accuracy, a differential probe should be used for measuring the voltage
across the resistor. For more information, refer to Power Jumpers (P4-7).
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
1-15
Example Programs
Example Programs
Example programs are provided with the ADSP-CM40x Enablement Software to demonstrate various capabilities of the product. The programs can
be found in the CM403F_CM408F_EZ-KIT\examples folder. Refer to a
readme file provided with each example for more information.
Reference Design Information
A reference design info package is available for download on the Analog
Devices Web site. The package provides information on the design, layout, fabrication, and assembly of the EZ-KIT Lite.
The information can be found at:
http://www.analog.com/CM408FEZKit
1-16
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2 ADSP-CM408F EZ-KIT LITE
HARDWARE REFERENCE
This chapter describes the hardware design of the ADSP-CM408F
EZ-KIT Lite board.
The following topics are covered.
• System Architecture
Describes the board’s configuration and explains how the board
components interface with the processor.
• Software-Controlled Switches (SoftConfig)
Lists and describes the processor signals routed through the software-controlled switches.
• Push Buttons and Switches
Shows the locations and describes the push buttons and switches.
• Jumpers
Shows the locations and describes the configuration jumpers.
• LEDs
Shows the locations and describes the LEDs.
• Connectors
Shows the locations and provides part numbers for the on-board
connectors. In addition, the manufacturer and part number information is provided for the mating parts.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-1
System Architecture
System Architecture
This section describes the processor’s configuration on the EZ-KIT Lite
board (Figure 2-1).
DB9
Female
Ethernet
RJ45
DB9
Female
TI
DP83848
Ethernet
ADM2682 USB otg
PHY
RS-485
RS-232
ADM3252E
CAN
RJ11
CAN
RJ11
ADI
ADM3053
ADI
ADM3053
UART0
UART1
USB0
CLKIN
TRACE
20 pin 0.05"
6 pin 0.1"
header
CAN0
ADSP-CM408F
CAN1
SPI2
LEDs (4)
32 Mbit Quad
SPI Flash
AFE
Debug
Port
JTAG
20 pin 0.1"
ETH0
GPIO
PBs (2)
30 MHz
Oscillator
3.3 Volts
2 – 16 bit ADCs
8 inputs each
SPT0
1588
Analog Connector
120 pin 0.5mm connector
AGND, 5V out, GND
TMR0:2
PWM0:2
SINC0
SRAM
4 Mbit Cypress
CY7C1041DV33
SMC0
CNT0:3
SPI1
TWI0
PWM Connector
180 pin 0.5mm connector
5V in, 5V out, 3.3V out, GND
UART2
Asynchronous connector
LCD
display
2x20
120 pin 0.5mm connector
5V in, 3.3V out, GND
Figure 2-1. EZ-KIT Lite Block Diagram
This EZ-KIT Lite is designed to demonstrate the ADSP-CM408F processor’s capabilities. The ADSP-CM408F EZ-KIT Lite has a 30 MHz input
clock and runs at 240 MHZ internally.
USB circuitry and a mini USB AB connector are provided for connecting
to the EZ-KIT Lite as a host or a device. The frequency for the USB circuit is generated internally to the processor.
2-2
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
User I/O to the processor is provided in the form of two user push buttons
and four LEDs. The software-controlled switches (SoftConfig) facilitate
the switch multi-functionality by disconnecting the push buttons from
their associated processor pins and reusing the pins elsewhere on the
board. See ADSP-CM408F EZ-KIT Lite Schematic for more information.
Software-Controlled Switches
(SoftConfig)
On the ADSP-CM408F EZ-KIT Lite, most of the traditional mechanical
switches have been replaced by I2C software-controlled switches. The
remaining mechanical switches are provided for the boot mode and push
buttons. Reference any SoftConfig*.c file found in the installation directory for an example of how to set up the SoftConfig feature of the
ADSP-CM408F EZ-KIT Lite through software.
The SoftConfig section of this manual serves as a reference to any user
that intends to modify an existing software example. If software provided
from ADI is used, there should be little need to reference this section.
should be taken when changing SoftConfig settings not to
 Care
create a conflict with interfaces. This is especially true when connecting extender cards.
Overview of SoftConfig
In order to further clarify the use of electronic single FET switches and
multi-channel bus switches, an example of each is illustrated and compared to a traditional mechanical switching solution. This is a generic
example that uses the same FET and bus switch components that are on
the EZ-KIT Lite.
After this generic discussion there is a detailed explanation of the SoftConfig interface specific to the ADSP-CM408F EZ-KIT Lite.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-3
Software-Controlled Switches (SoftConfig)
Figure 2-2 shows two individual FET switches (Pericom PI3A125CEX)
with reference designators UA and UB. Net names ENABLE_A and ENABLE_B
control UA and UB. The default FET switch enable settings in this example are controlled by resistors RA and RB which pull the enable pin 1 of UA
and UB to ground (low). In a real example, these enable signals are controlled by the Microchip IO expander. The default pull-down resistors
connects the signals EXAMPLE_SIGNAL_A and EXAMPLE_SIGNAL_B and also
connects signals EXAMPLE_SIGNAL_C and EXAMPLE_SIGNAL_D. To disconnect
EXAMPLE_SIGNAL_A from EXAMPLE_SIGNAL_B, the Microchip IO expander is
used to change ENABLE_A to a logic 1 through software that interfaces with
the Microchip. The same procedure for ENABLE_B would disconnect EXAMPLE_SIGNAL_C from EXAMPLE_SIGNAL_D.
Figure 2-2. Example of Individual FET Switches
2-4
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Figure 2-3 shows the equivalent circuit to Figure 2-2 but utilizes mechanical switches that are in the same package. Notice the default is shown by
black boxes located closer to the ON label of the switches. In order to disconnect these switches, physically move the switch to the OFF position.
Figure 2-3. Example of Mechanical Switch Equivalent to Figure 2-2
Figure 2-4 shows a bus switch example, reference designator UC (Pericom
PI3LVD512ZHE), selecting between lettered functionality and numbered
functionality. The signals on the left side are multiplexed signals with
naming convention letter_number. The right side of the circuit shows the
signals separated into letter and number, with the number on the lower
group (eg. 0B1) and the letter on the upper group (eg. 0B2). The default
setting is controlled by the signal CONTROL_LETTER_NUMBER which is pulled
low. This selects the number signals on the right to be connected to the
multiplexed signals on the left by default. In this example, the Microchip
IO expander is not shown but controls the signal CONTROL_LETTER_NUMBER
and allows the user to change the selection through software.
Figure 2-5 shows the equivalent circuit to Figure 2-4 but utilizes mechanical switches. Notice the default for reference designators SWC and SWD is
illustrated by black boxes located closer to the ON label of the switches to
enable the number signals by default. Also notice the default setting for
reference designators SWE and SWF is OFF. In order to connect the letters
instead of the numbers, the user physically changes all switches on SWC and
SWD to the OFF position and all switches on SWE and SEF to the ON position.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-5
Software-Controlled Switches (SoftConfig)
Figure 2-4. Example of Bus Switch
2-6
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Figure 2-5. Example of Mechanical Switch Equivalent to Figure 2-4
SoftConfig on the ADSP-CM408F EZ-KIT LITE
Two Microchip MCP23017 GPIO expanders provide control for individual electronic switches. The TWI0 interface of the processor
communicates with the Microchip devices.There are 33 individual
switches with default settings that enable basic board functionality.
Table 2-1 lists the ADSP-CM408F processor and EZ-KIT Lite interfaces
that are available by default. Note that only interfaces affected by software
switches are listed in Table 2-1.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-7
Software-Controlled Switches (SoftConfig)
Table 2-1. Default ADSP-CM408F Processor Interface Availability
Interface
Availability by Default
UART0
RS-232 RX, TX and RTS enabled by default. SoftConfig required for other
functionality.
UART1
RS-485 is connected by default but not enabled. SoftConfig is required to
enable.
CAN0
Enabled
CAN1
Enabled
EMAC0
RMII interface, management data input/output and 50 MHz oscillator
disabled by default. PHYINT disconnected from processor by default.
Push buttons
Enabled (except for wake push button)
LEDs
Enabled
Programming SoftConfig Switches
On the ADSP-CM408F EZ-KIT Lite, two Microchip MCP23017 devices
exist. Each of these devices have the following programming
characteristics:
• Each switch has two programmable GPIO registers.
GPIO Register
Register Address
GPIOA
0x12
GPIOB
0x13
• Each GPIO register controls eight signals (software switches).
2-8
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
• By default, the Microchip MCP23017 GPIO signals function as
input signals.
The signals must be programmed as output signals to override their
default values. The following table shows the Microchip register
addresses and the values that must be written to them to program
the signals as output signals.
IODIR Register IODIR Register Address Value to be Written to Program Signals
as Outputs
IODIRA
0x00
0
IODIRB
0x01
0
Each of the examples in the ADSP-CM40x Enablement Software include
source files that program the soft switches, even if the default settings are
being used. The README for each example identifies only the signals that
are being changed from their default values. The code that programs the
soft switches is located in the SoftConfig_CM408F.c file in each example.
The following tables (Table 2-2 and Table 2-3) outline the default values
for each of the two Microchip MCP23017 devices.
Table 2-2. I2C Hardware Address 0x40
GPIO
MCP23017 Register Address
Default Value
GPIOA
0x12
0xE0
GPIOB
0x13
0x00
Table 2-3. I2C Hardware Address 0x42
GPIO
MCP23017 Register Address
Default Value
GPIOA
0x12
0xB9
GPIOB
0x13
0x3F
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-9
Software-Controlled Switches (SoftConfig)
The ADSP-CM408F EZ-KIT Lite Schematic shows how the two Microchip GPIO expanders are connected to the board’s ICs.
Table 2-4 and Table 2-5 show the output signals of the Microchip GPIO
expander (U40), with a TWI address of 0100 001X, where X represents the
read or write bit. The signals that control an individual FET have an entry
under the FET column. The Component Connected column shows the
board IC that is connected if the FET is enabled. The Microchip (U40) is
controlling the enable signal of a FET switch. Also note that if a particular
functionality of the processor signal is being used, it will be in bold font
under the Processor Signal column.
Table 2-4. Output Signals of Microchip GPIO Expander
(U40 Port A)
Bit Signal Name
Description
0
Not used
Low
1
Not used
Low
2
Not used
Low
3
UART0RTS_EN
FET Processor Signal
(if applicable)
Component Default
Connected
UART0 RTS
U13 PB_04/PWM2_SYNC/
UART0_RTS/
connected to RS-232
SPT0_ATDV/
transceiver
U36
Low
SMC0_D12/CNT1_UD
4
UART0RX_EN
UART0 RX
U14 PC_01/UART0_RX/
SMC0_A05/TM0_ACI5
connected to RS-232
transceiver
U36
Low
5
UART0CTS_EN
UART0 CTS
disconnected from
RS-232 transceiver
by default
U36
High
2-10
U15
PB_05/PWM2_TRIP0/
UART0_CTS/TM0_TMR7/SMC0_D13/
CNT1_DG
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Table 2-4. Output Signals of Microchip GPIO Expander
(U40 Port A) (Cont’d)
Bit Signal Name
Description
FET Processor Signal
(if applicable)
6
UART0CTS_RTS_LPBK
UART0 CTS and
U16
RTS not connected;
change to low for
looping back RS-232
CTS and RTS signals
U36
High
7
UART0CTS_RST_EN
UART0 CTS signal
not connected to
input of reset IC
U36
High
U17
Component Default
Connected
Table 2-5. Output Signals of Microchip GPIO Expander
(U40 Port B)
Bit Signal Name
Description
FET
Processor Signal
(if applicable)
0
CAN0_EN
Enables CAN 0,
enabled by default
U18/
U19
PC_00/CAN0_TX/
U39
SPT1_BTDV/
UART1_TX/
SMC0_A04 and
PB_15/CAN0_RX/
SPT1_ATDV/
UART1_RX/
SMC0_A03/TM0_ACI4
Low
1
PUSHBUTTON1_EN
PF_10 is used as GPIO
input for push button
1, enabled by default
U31
PF_10/ETH0_PTP- U39
CLKIN
Low
2
PUSHBUTTON2_EN
PE_08 is used as GPIO
input for push button
2, enabled by default
U30
PE_08/
ETH0_PTPPPS/
SMC0_A22/
CNT2_ZM
Low
3
LED1_GPIO_EN
PE_07 is used as GPIO
output for LED1,
enabled by default
U28
PE_07/ETH0_PTU5
PAUXIN/SMC0_A21
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Component Default
Connected
U39
Low
2-11
Software-Controlled Switches (SoftConfig)
Table 2-5. Output Signals of Microchip GPIO Expander
(U40 Port B) (Cont’d)
Bit Signal Name
Description
FET
Processor Signal
(if applicable)
Component Default
Connected
4
LED2_GPIO_EN
PE_06
is used as GPIO
output for LED2,
enabled by default
U27
PE_06/SMC0_A20
U5
Low
5
LED3_GPIO_EN
PE_05
is used as GPIO
output for LED3,
enabled by default
U26
PE_05/SMC0_A19
U5
Low
6
LED4_GPIO_EN
PE_09
is used as GPIO
output for LED4,
enabled by default
U25
PE_09/ETH0_CRS/ U5
SMC0_A23/
CNT2_UD
Low
7
Not used
Table 2-6 and Table 2-7 show the output signals of the Microchip GPIO
expander (U41), with a TWI address of 0100 010X, where X represents the
read or write bit. The signals that control an individual FET have an entry
under the FET column. The Component Connected column shows the
board IC that is connected if the FET is enabled. Note that some of the
Microchip (U41) output signals are connected directly to components on
the board. However, in most cases, the Microchip (U41) is controlling the
enable signal of a FET switch. Also note that if a particular functionality
of the processor signal is being used, it will be in bold font under the Processor Signal column.
2-12
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Table 2-6. Output Signals of Microchip GPIO Expander
(U41 Port A)
Bit Signal Name
Description
0
RS485_RE
Controls RS-485
receiver enable
U39
High
1
RS485_DE
Controls RS-485
driver enable
U39
Low
2
CAN1_EN
Enables CAN 1,
enabled by default
U20/U21
PB_11/SINC0_D0/
U37
SPI0_D3/CAN1_TX/
SMC0_AMS0/TM0_ACLK1 and PB_10/
SINC0_CLK0/
SPI0_D2/CAN1_RX/
SMC0_AWE/TM0_ACI1
Low
3
ETH0_MDIO_BUS_EN
Connects Ethernet
management data
input/output, disabled by default
U22/U23
PE_11/ETH0_MDC/
SMC0_A24/CNT3_ZM
and PE_10/ETH_MDIO/SMC0_AMS1/
CNT2_DG
U43
High
4
ETHERNET_EN
Connects ETH0 to
RMII interface of
U32, by default
disabled
U32
PF_00, PF_01,
PE_12, PE_13,
PE_14, PE_09
U43
High
5
PHYINT_EN1
Connects Ethernet 0
interrupt signal to
Ethernet PHY, not
connected by default
U24
PC_06/SPI0_SEL1/
PWM2_DL/SYS_DSWAKE0
U43
High
6
RMII_CLK_EN
Enables 50 MHz
oscillator, disabled by
default
PE_15/ETH0_REFCLK/CNT1_OUTB
U35
Low
7
WAKE_PUSHBUTTON_EN
Connects processor to U29
wake push button,
disabled by default
PC_06/SPI0_SEL1/
PWM2_DL/SYS_DSWAKE0_ACLK3
1
FET/
Processor Signal
SWITCH (if applicable)
Component Default
Connected
High
This signal is actually active low.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-13
Software-Controlled Switches (SoftConfig)
Table 2-7. Output Signals of Microchip GPIO Expander
(U41 Port B)
Bit Signal Name
Description
FET/
Processor Signal
SWITCH (if applicable)
Component Default
Connected
0
DATA_LOW_EXP_EN
Connects signals to
expansion interface
connector J6,
disconnected by default
U12
PC_08,
PC_10,
PC_12,
PC-14,
PC_09,
PC_11,
PC_13,
PC_15
J6
High
1
DATA_HIGH_EXP_EN
Connects signals to
expansion interface
connector J6,
disconnected by default
U11
PD_00,
PD_02,
PD_04,
PD_06,
PD_01,
PD_03,
PD_05,
PD_07
J6
High
2
TRACE_EXP_EN
Connects signals to
expansion interface
connector J6,
disconnected by default
U51,
U52,
U53,
U54,
U55
PE_12, PE_13,
PE_09, PE_11,
PE_10
J6
High
3
PB_08_09_EXP_EN
Connects signals to
expansion interface
connector J6,
disconnected by default
U49/U50
PB_08/PWM2_BH/
TM0_TMR1/
UART1_RX/
SMC0_ARDY/
TM0_ACI2
J6
High
and
PB_09/PWM2_BL/
TM0_TMR2/
UART1_TX/
SMC0_ARE
4
ETH_EXP_EN
Connects signals to
expansion interface
connector J4,
disconnected by default
U56,
U57,
U58,
U59,
U60
PE_12, PE_13,
PE_09, PE_11,
PE10
J4
High
5
SRAM_BYTE_EN
Connects SRAM ABE0/
1 signals to SRAM
U4, U7
PE_12, PE_13
U2
High
6
Not used
Low
7
Not used
Low
2-14
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Push Buttons and Switches
This section describes operation of the push buttons and switches. The
push button and switch locations are shown in Figure 2-6.
Figure 2-6. Push Button and Boot Mode Switch Locations
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-15
Push Buttons and Switches
Boot Mode Select Switch (SW1)
The rotary switch (SW1) determines the boot mode of the processor.
Table 2-8 shows the available boot mode settings. By default, the
ADSP-CM408F processor boots from the internal SPI flash memory.
Table 2-8. Boot Mode Select Switch (SW1)
SW1 Position
Processor Boot Mode
0
No Boot – Idle
1
SPI master boot (internal SP12). Default boot mode.
2
SPI slave boot (SPI0)
3
UART boot (UART0)
Reset Push Button (SW2)
The reset push button (SW2) resets the following ICs: processor (U1),
GPIO extender (U40), GPIO extender (U41), and Ethernet PHY (U43).
The reset also is connected to the expansion interface via the SYS_HWRST
signal.
GPIO Push Buttons (SW4-5)
The GPIO push buttons (SW4 and SW5) are connected to the processor’s
signals PF_10/ETH0_PTPCLKIN and PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM,
respectively. The signals are connected by default.
2-16
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Wake Push Button (SW3)
The wake push button (SW3) is connected to the processor’s signal
PC_06/SPI0_SEL1/PWM2_DL/SYS_DSWAKE0. The signal is disconnected by
default through SoftConfig.
Jumpers
This section describes functionality of the configuration jumpers.
Figure 2-7 shows the jumper locations.
Figure 2-7. Jumper Locations
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-17
Jumpers
VREF1 External Source Jumper (JP1)
The VREF1 external source jumper (JP1) selects whether an internal or
external voltage reference supplies the VREF1 signal of the processor. When
a jumper on JP1 is not installed (default), the internal voltage reference
supplies VREF1. When a jumper on JP1 is installed, the external Analog
Devices ADR441 ultra-low noise voltage reference (U47) supplies VREF1.
Configure the processor’s registers accordingly for the latter case.
Power Select Jumper (JP2)
The power select jumper (JP2) selects the wall power (5V) when a jumper
is placed on positions 1 and 2. When a jumper is placed on positions 2
and 3, power from pins 177, 178, 179 and 180 of the PWM connector
(J6) is supplied to the board. The default setting is positions 1 and 2,
which selects wall power.
Buffer Input Select Jumper (JP3)
The buffer input select jumper (JP3) selects the input to the ADA4889
unity gain op amp buffer (U33). The processor’s internal input is selected
by placing a jumper on pins 1 and 2 of JP3 (default).
The external VREF0 input, supplied by the Analog Devices ADR441
ultra-low noise voltage reference (U6), is selected by placing a jumper on
pins 2 and 3 of JP3.
2-18
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
VREF0 External Source Jumper (JP4)
The VREF0 external source jumper (JP4) selects whether an internal or
external voltage reference supplies the VREF0 signal of the processor. When
a jumper on JP4 is not installed (default), the internal voltage reference
supplies VREF0. When a jumper on JP4 is installed, the external Analog
Devices ADR441 ultra-low noise voltage reference (U6) supplies VREF0.
Configure the processor’s registers accordingly for the latter case.
Power Jumpers (P4-7)
Remove jumpers listed in Table 2-9 to measure the respective voltage
across the adjacent sense resistor.
Table 2-9. Power Jumpers
Power Jumper
Resistor
P4
USB_VBUS
P5
VDD_EXT
P6
VDD_INT
P7
3.3V
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-19
LEDs
LEDs
This section describes the on-board LEDs. Figure 2-8 shows the LED
locations.
Figure 2-8. LED Locations
2-20
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
GPIO LEDs (LED1–4)
Four LEDs are connected to the general-purpose I/O pins of the processor
(see Table 2-10). The LEDs are active high and are ON (amber) by writing
a 1 to the correct processor signal.
Table 2-10. GPIO LEDs
LED Reference Designator
Processor Programmable Flag Pin
LED1
PE_07
LED2
PE_06
LED3
PE_05
LED4
PE_09
Reset LED (LED5)
When LED5 is ON (red), it indicates that the master reset of all the major
ICs is active. The reset LED is controlled by the Analog Devices ADM708
supervisory reset circuit. A master reset is asserted by pressing SW2 which
activates LED5. For more information, see Reset Push Button (SW2).
Ethernet Speed LED (LED6)
The Ethernet speed LED (LED6) is a green LED that shows the connection
speed when the Ethernet is enabled. When LED6 is ON, the speed is 100
Mb/s; when LED6 is OFF, the speed is 10 Mb/s. For more information, see
Ethernet Interface.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-21
LEDs
Power LED (LED7)
When LED7 is ON (green), it indicates that power is being supplied to the
board properly. For more information, see Power Architecture.
SYS_FAULT LED (LED8)
When SYS_FAULT LED LED8 (red) is ON, it indicates a system fault. For
more information, refer to the ADSP-CM40x Mixed-Signal Control Processor Hardware Reference.
2-22
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Connectors
This section describes connector functionality and provides information
about mating connectors. The connector locations are shown in
Figure 2-9.
Figure 2-9. Connector Locations
 Connectors on the back of the board are noted with dotted lines.
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-23
Connectors
Ethernet Connector (J1)
Part Description
Manufacturer
Part Number
RJ45
PULSE ELECTRONICS
J0011D21BNL
Mating Cable
Standard Ethernet cable
RS-485 Connector (J2)
Part Description
Manufacturer
Part Number
DB9 female
NORCOMP
191-009-213-L-571
DCE UART Connector (J3)
Part Description
Manufacturer
Part Number
DB9 female
NORCOMP
191-009-213-L-571
Asynch or Memory Connector (J4)
Part Description
Manufacturer
Part Number
180-pin high speed socket
SAMTEC
QSH-090-F-D_A
Mating Connector
180-pin high speed header
2-24
SAMTEC
QTH-090-01-F-D-A
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
Character Display Connector (J5)
The character display connector (J5) is a socket that mates with the 20 x 2
character display.
Part Description
Manufacturer
Part Number
IDC 5x2 SMT
SAMTEC
SSW-105-22-F-D-VS
Mating Connector
20x2 character display with backlight
NEW HAVEN DISPLAY
NHD-0220D3Z-FL-GBW
(requires header)
Part Description
Manufacturer
Part Number
180-pin high speed socket
SAMTEC
QSH-090-F-D_A
PWM Connector (J6)
Mating Connector
180-pin high speed header
SAMTEC
QTH-090-01-F-D-A
CAN0 Connector (J7)
Part Description
Manufacturer
Part Number
RJ11 vertical
DIGIKEY
A31431-ND
Mating Connector
RJ11 cable
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-25
Connectors
CAN1 Connector (J8)
Part Description
Manufacturer
Part Number
RJ11 vertical
DIGIKEY
A31431-ND
Mating Connector
RJ11 cable
Analog Connector (J9)
Part Description
Manufacturer
Part Number
120-pin high speed socket
SAMTEC
QSH-060-F-D_A
Mating Connector
120-pin high speed header
SAMTEC
QTH-060-01-F-D-A
JTAG/SWD Connector (P1)
The JTAG/SWD/SWV header (P1) provides debug connectivity for the
microprocessor. This is a 0.1” connector from SAMTEC
(SHF-110-01-L-D-TH). For more information, see Debug Interface.
TRACE and JTAG/SWD/SWV Connector (P2)
The TRACE and JTAG/SWD/SWV Connector (P1) provides connectivity to the microprocessor’s trace interface. This is a 0.05” connector from
TE Connectivity (5103308-5).
Pin 7 is cut to provide keying.
Refer to the SoftConfig tables for information on enabling the Trace signals, specifically the TRACE_EXP_EN signal.
2-26
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Hardware Reference
USB Connector (P3)
USB FS only mode.
Part Description
Manufacturer
Part Number
USB mini-B
MOLEX
56579-0576
IEEE 1588 Connector (P8)
P8 allows probing of Ethernet IEEE 1588 signals. P8 is a 0.1” header and
the pinout can be found in ADSP-CM408F EZ-KIT Lite Schematic.
Power Connector (P9)
Part Description
Manufacturer
Part Number
0.65 mm power jack
CUI
045-0883R
Mating Connector
[email protected] power supply
GLOBETEK
GS-1750(R)
VREF Buffered Connector (P10)
The VREF buffered connector provides a means to measure the voltage of
the voltage reference. There is an adjacent analog grounding point (TP13).
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
2-27
Connectors
2-28
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
A ADSP-CM408F EZ-KIT LITE
BILL OF MATERIALS
The bill of materials corresponds to ADSP-CM408F EZ-KIT Lite
Schematic.
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
1
1
ADM708SARZ SOIC8
U42
ANALOG
DEVICES
ADM708SARZ
2
2
ADR441ARMZ
MSOP8
U6,U47
ANALOG
DEVICES
ADR441ARMZ
3
1
ADP2118ACPZ
QFN65P400X400X8017N
VR2
ANALOG
DEVICES
ADP2118ACPZ
4
1
ADP2119ACPZ-R7
DFN50P300X300-11N
VR1
ANALOG
DEVICES
ADP2119ACPZ-R7
5
1
ADA4899 SOIC8
U33
ANALOG
DEVICES
ADA4899-1YRDZ-R7
6
1
ADM2682E
SOIC127P1032X265-1
6N
U39
ANALOG
DEVICES
ADM2682EBRIZ
7
1
ADM3252E
BGA44C100P11X11_1
200X1200X103
U36
ANALOG
DEVICES
ADM3252EABCZ
8
2
ADM3053
SOIC127P1032X265-2
0N
U37,U38
ANALOG
DEVICES
ADM3053BRWZ
9
1
ADSP-CM408BSWZ
LQFP176_EP
U1
ANALOG
DEVICES
ADSP-CM408FBSWZENG
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
A-1
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
10
62
0.1UF 10V 10% 0402
C1,C5-C7,C1
7,C18,C22,C2
5,C26,C29,C3
1,C34-C36,C4
0,C43,C45,C4
8,C50,C54-C5
6,C59,C60,C6
2-C65,C67,C6
8,C72,C78,C7
9,C101,C102,
C104,C109,C1
19,C120,C122
-C125,C128-C
130,C132,C13
5,C136,C138,
C139,C143,C1
48-C150,C153
-C157,C174,C
179
AVX
0402ZD104KAT2A
11
74
0.01UF 16V 10% 0402
C2,C8,C9,C19
-C21,C24,C30
,C32,C33,C46
,C47,C49,C51
,C53,C61,C66
,C69-C71,C73
-C76,C80-C90
,C92,C110-C1
18,C121,C131
,C134,C141,C
144,C151,C15
2,C158-C173,
C175-C178,C
180,C181
AVX
0402YC103KAT2A
12
1
4.7UF 25V 20% 0805
C142
AVX
0805ZD475KAT2A
13
1
10UF 16V 10% 1210
C98
AVX
1210YD106KAT2A
14
2
1000PF 50V 5% 1206
C97,C99
AVX
12065A102JAT2A
A-2
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Bill Of Materials
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
15
2
680 1/16W 1% 0402
R210,R211
BC
COMPONENTS
2312 275 16801
16
1
1.5UH 20% IND003
L2
COIL CRAFT
DO1608C-152MLC
17
1
1.5UH 20%
INDC4040X210N
L1
COILCRAFT
XAL4020-152MEB
18
1
ROTARY SWT027
SW1
COPAL
S-8110
19
1
CY7C1041CV33
BGA48_75_810
U2
CYPRESS
CY7C1041DV33-10BVXI
20
1
PWR .65MM CON045
P9
DIGI-KEY
CP1-023-ND
21
1
50MHZ OSC012
U35
DIGI-KEY
300-8264-2-ND
22
2
MCP23017
QFN65P600X600-29N
U40,U41
DIGI-KEY
MCP23017-E/ML-ND
23
2
1UF 16V 10% 0805
C95,C96
DIGI-KEY
399-1284-2-ND
24
2
GREEN LED_0603
LED6,LED7
DIGI-KEY
475-1409-2-ND
25
3
0.1UF 16V 10% 0402
C37-C39
DIGI-KEY
587-1451-2-ND
26
1
15KV ESDA6V1SC
SOT95P280-6N
D4
DIGI-KEY
497-6637-1-ND
27
1
30MHZ OSC012
U34
DIGI-KEY
300-8257-1-ND
28
2
RED LED_0603
LED5,LED8
DIGI-KEY
475-2512-2-ND
29
4
YELLOW LED_0603
LED1-LED4
DIGI-KEY
475-2558-1-ND
30
1
10UF 6.3V 20% 0402
C14
DIGI-KEY
445-8920-1-ND
31
1
SN74CB3Q3245
TSSOP20
U32
DIGI-KEY
296-19130-1-ND
32
1
MIC2025-1 SOIC8
U44
DIGI-KEY
576-1057-ND
33
1
STD2805T4
TO228P972X240-3N
Q1
DIGI-KEY
497-7465-1-ND
34
8
IDC 2PIN_JUMPER_SHORT
SJ1-SJ8
DIGI-KEY
S9001-ND
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
A-3
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
35
1
150UF 10V 10% D
CT2
DIGI-KEY
478-3321-2-ND
36
2
107.0 1/10W 1% 0805
R101,R107
DIGI-KEY
311-107CRTR-ND
37
1
1K 1/10W 5% 0603
R170
DIGI-KEY
311-1.0KGRTR-ND
38
2
4700PF 16V 10% 0603
C44,C52
DIGI-KEY
311-1083-2-ND
39
10
2.21K 1/10W 1% 0603
R78,R80,R84R86,R108-R11
2
DIGI-KEY
311-2.21KHRTR-ND
40
3
100 1/16W 5% 0402
R132,R137,R1
39
DIGI-KEY
311-100JRTR-ND
41
7
330.0 1/16W 1% 0402
R115-R119,R1
31,R172
DIGI-KEY
541-330LCT-ND
42
2
165.0 1/10W 1% 0603
R102,R106
DIGI-KEY
P165HTR-ND
43
1
220.0 1/10W 1% 0603
R77
DIGI-KEY
P220HTR-ND
44
1
4.87K 1/10W 1% 0402
R82
DIGI-KEY
541-4.87KHCT-ND
45
7
IDC 2X1 IDC2X1
JP1,JP4,P4-P7,
P10
FCI
90726-402HLF
46
2
IDC 3X1 IDC3X1
JP2,JP3
FCI
90726-403HLF
47
1
120.0 1/16W 1% 0603
R44
FEC
933-0496
48
1
IDT74FCT3244APY
SSOP20
U5
IDT
IDT74FCT3244APYG
49
1
TEST LOOP
LOOP_2838
GP1
KEYSTONE
5016
50
1
VARISTOR V5.5MLA
30A 0603
R1
LITTLEFUSE
V5.5MLA0603
51
1
THERM 0.5A 0.4 1206
R186
LITTLEFUSE
1206L050-C
52
1
USB_MINI-AB 5PIN
CON052
P3
MOLEX
56579-0576
53
1
IDC 10X2
TE_5103308-5
P1
MOUSER
571-5103308-5
A-4
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Bill Of Materials
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
54
7
10UF 6.3V 20% 0603
C10,C11,C13,
C126,C127,C1
33,C140
MULTICOMP
MCCA000517
55
1
190 100MHZ 5A
FER002
FER4
MURATA
DLW5BSN191SQ2
56
1
DP83848 LQFP48
U43
NATIONAL
SEMI
DP83848CVV/NOPB
57
2
DB9 9PIN CON038
J2,J3
NORCOMP
191-009-213-L-571
58
1
GTL2002 TSSOP8
U10
NPX
GTL2002DP,118
59
3
5A MBRS540T3G SMC
D6-D8
ON SEMI
MBRS540T3G
60
1
15KV ESD7004
DFN50P250X100-10N
D5
ON SEMI
ESD7004MUTAG
61
4
MOMENTARY
SWT024
SW2-SW5
PANASONIC
EVQ-Q2K03W
62
27
0 1/16W 5% 0402
R6,R8,R17,R4
5,R46,R49,R6
2,R63,R146,R
147,R151,R16
0,R163,R168,
R185,R190-R1
93,R196,R198,
R199,R202,R2
14,R229,R230,
R232
PANASONIC
ERJ-2GE0R00X
63
13
0 1/16W 5% 0402
R11,R12,R47,
R48,R149,R15
9,R164,R166,
R184,R200,R2
01,R212,R213
PANASONIC
ERJ-2GE0R00X
64
4
1UF 6.3V 20% 0402
C12,C91,C93,
C94
PANASONIC
ECJ-0EB0J105M
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
A-5
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
65
11
10UF 10V 10% 0805
C15,C16,C23,
C27,C28,C41,
C42,C57,C58,
C77,C137
PANASONIC
ECJ-2FB1A106K
66
1
1.50K 1/16W 1% 0402
R91
PANASONIC
ERJ-2RKF1501X
67
2
27K 1/16W 5% 0402
R187,R188
PANASONIC
ERJ-2GEJ273X
68
4
60.4 1/10W 1% 0603
R64,R65,R68,
R69
PANASONIC
ERJ-3EKF60R4V
69
1
45.3K 1/10W 1% 0402
R157
PANASONIC
ERJ-2RKF4532X
70
1
24.9 1/10W 1% 0402
R13
PANASONIC
ERJ-2RKF24R9X
71
1
10UF 10V 20%
ELEC_4MM
CT1
PANASONIC
EEE-1AA100NR
72
33
PI3A125 SC70_5
U4,U7,U13-U
31,U49-U60
PERICOM
PI3A125CEX
73
2
PI4ULS3V08M
QFN40P300X600X7533N
U11,U12
PERICOM
PI4ULS3V08MZLE
74
4
0.0 1/10W 1% 0603
R16,R176,R17
7,R203
PHYCOMP
232270296001L
75
1
RJ45 W/LEDS
CON065
J1
PULSE ENG.
J0011D21BNL
76
1
200.0K 1/16W 1%
0402
R209
ROHM
MCR01MZPF2003
77
1
IDC 3X2
IDC3X2_SMT
P8
SAMTEC
TSM-103-01-T-DV
78
1
IDC 5X2
IDC5x2_SMT_F
J5
SAMTEC
SSW-105-22-F-D-VS
79
1
0.05 10X2 SAMTEC_SHF-110-01-L-DTH
P2
SAMTEC
SHF-110-01-L-D-TH
A-6
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
ADSP-CM408F EZ-KIT Lite Bill Of Materials
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
80
2
0.5MM 180PIN SAMTEC_QSH-090-F-D-A
J4,J6
SAMTEC
QSH-090-01-F-D-A
81
1
0.5MM 120PIN SAMTEC_QSH-060-F-D-A
J9
SAMTEC
QSH-060-01-F-D-A
82
4
0.05 1/2W 1% 1206
R150,R154,R1
56,R165
SEI
CSF 1/2 0.05 1%R
83
10
49.9 1/16W 1% 0402
R89,R90,R92,
R93,R96,R98,
R103-R105,R1
55
STACKPOLE
RMCF0402FT49R9
84
3
600 100MHZ 500MA
1206
FER1-FER3
STEWARD
HZ1206B601R-10
85
1
74LVC14A SOIC14
U3
TI
74LVC14AD
86
1
SN74LVC1G08
SOT23-5
U48
TI
SN74LVC1G08DBVE
87
2
SN74LVC1G08
SOT23-5
U45,U46
TI
SN74LVC1G08DBVE
88
2
RJ11 4PIN CON039
J7,J8
TYCO
5558872-1
89
1
3A RESETABLE
FUS004
F1
TYCO
SMD300F-2
90
3
0 1/8W 5% 0805
R15,R97,R178
VISHAY
CRCW08050000Z0EA
91
20
10K 1/16W 5% 0402
R2-R5,R30-R3
2,R36,R37,R3
9,R41,R42,R5
1,R75,R152,R
153,R182,R19
7,R219,R220
VISHAY
CRCW040210K0FKED
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
A-7
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
92
78
10K 1/16W 5% 0402
R10,R14,R18R20,R27-R29,
R33-R35,R38,
R40,R43,R52R58,R66,R67,
R70,R71,R79,
R81,R83,R87,
R88,R94,R95,
R100,R113,R1
14,R120-R130
,R133-R135,R
138,R140-R14
3,R148,R158,
R161,R171,R1
73-R175,R180
,R189,R194,R
195,R215-R21
8,R221-R228,
R231
VISHAY
CRCW040210K0FKED
93
9
33 1/16W 5% 0402
R7,R9,R59,R6
0,R76,R99,R1
36,R144,R145
VISHAY
CRCW040233R0JNEA
94
2
10K 1/10W 5% 0603
R204,R205
VISHAY
CRCW060310K0JNEA
95
1
1M 1/10W 5% 0603
R179
VISHAY
CRCW06031M00FNEA
96
6
10 1/10W 5% 0603
R61,R72-R74,
R162,R167
VISHAY
CRCW060310R0JNEA
97
1
30A GSOT05 SOT23-3
D1
VISHAY
GSOT05-GS08
98
2
30A GSOT03 SOT23-3
D2,D3
VISHAY
GSOT03-GS08
99
6
22UF 16V 10% 1210
C100,C103,C1
05-C108
YAIYO YUDEN
EMK325BJ226KM-T
A-8
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
A
B
C
D
1
1
ADSP-CM408F EZ-KIT
SCHEMATIC
2
2
3
3
ANALOG
DEVICES
4
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
TITLE PAGE
Title
Size
20 Cotton Road
0.2A
Sheet
07/02/2013
D
1
of
13
A
B
C
D
3.3V
TRACE AND JTAG/SWD
U1
25
PA_00/PWM0_SYNC/SPT1_ACLK
PA_01/PWM0_TRIP0/SPT1_AFS
20
PA_02/PWM0_AH/SPT1_AD0
PA_02/PWM0_AH/SPT1_AD0
PC_01/UART0_RX/SMC0_A05/TM0_ACI5
PC_02/UART0_TX/TRACE_D03/SPI0_RDY 63
PC_02/UART0_TX/TRACE_D03/SPI0_RDY
60
PC_03/SPI0_CLK/PWM2_CH
PA_03/PWM0_AL/SPT1_AD1
PA_04/PWM0_BH/SPT1_BCLK
10
12
13
14
15
16
PC_08/SPT0_BCLK/SMC0_D00
17
18
19
20
PC_06/SPI0_SEL1/PWM2_DL/SYS_DSWAKE052
PC_07/SINC0_CLK1/UART2_TX/UART1_RTS/SYS_DSWAKE149
12
40
PC_09/SPT0_BFS/SMC0_D01
PC_09/SPT0_BFS/SMC0_D01
38
PC_10/SPT0_BD0/SMC0_D02
PC_10/SPT0_BD0/SMC0_D02
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D0310
3
11
PC_12/SPI1_CLK/SMC0_D04
PA_12/PWM1_AH/TM0_TMR4/SMC0_D04
JTG_TMS/SWDIO
JTG_TCK/SWCLK
JTG_TDO/SWO
pin 7 cut
JTG_TDI
R45
0402
0
JTAG_BOARD_RESET
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD
1
TRACE_D01/JTG_TRST
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM
PF_02/USB0_VBC/TRACE_D03
SAMTEC_SHF-110-01-L-D-TH
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03
PC_12/SPI1_CLK/SMC0_D04
1
PA_13/PWM1_AL/TM0_TMR5/SMC0_D05
9
PC_13/SPI1_MISO/SMC0_D05
PC_13/SPI1_MISO/SMC0_D05
173
PA_14/PWM1_BH/TM0_TMR6/SMC0_D06
7
PC_14/SPI1_MOSI/SMC0_D06
PC_14/SPI1_MOSI/SMC0_D06
PA_15/PWM1_BL/TM0_TMR3/SMC0_D07
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS 5
170
PA_15/PWM1_BL/TM0_TMR3/SMC0_D07
PC_07/SINC0_CLK1/UART2_TX/UART1_RTS/SYS_DSWAKE1
39
PC_08/SPT0_BCLK/SMC0_D00
4PA_11/PWM1_TRIP0/UART1_CTS/SMC0_D03/TM0_ACLK2
PA_14/PWM1_BH/TM0_TMR6/SMC0_D06
PC_06/SPI0_SEL1/PWM2_DL/SYS_DSWAKE0
13
PA_10/PWM1_SYNC/SMC0_D02/TM0_ACLK3
PA_13/PWM1_AL/TM0_TMR5/SMC0_D05
8
9
6
PA_12/PWM1_AH/TM0_TMR4/SMC0_D04
7
11
PA_09/PWM1_CL/SMC0_D01/TM0_ACLK4
PA_11/PWM1_TRIP0/UART1_CTS/SMC0_D03/TM0_ACLK2
6
PC_05/SPI0_MOSI/PWM2_DH
PA_08/PWM1_CH/SMC0_D00/TM0_ACLK5
PA_10/PWM1_SYNC/SMC0_D02/TM0_ACLK3
5
51
PC_05/SPI0_MOSI/PWM2_DH
14PA_07/PWM0_CL/SMC0_AMS2/SPT1_BD1
PA_09/PWM1_CL/SMC0_D01/TM0_ACLK4
4
17
PA_06/PWM0_CH/SPT1_BD0
PA_08/PWM1_CH/SMC0_D00/TM0_ACLK5
PC_03/SPI0_CLK/PWM2_CH
3
PC_04/SPI0_MISO/PWM2_CL
16
PA_07/PWM0_CL/SMC0_AMS2/SPT1_BD1
0
2
54
PC_04/SPI0_MISO/PWM2_CL
PA_05/PWM0_BL/SPT1_BFS
PA_06/PWM0_CH/SPT1_BD0
R196
0402
1
18
PA_04/PWM0_BH/SPT1_BCLK
PA_05/PWM0_BL/SPT1_BFS
P2
PC_00/CAN0_TX/SPT1_BTDV/UART1_TX/SMC0_A04
PC_01/UART0_RX/SMC0_A05/TM0_ACI5 62
19
PA_03/PWM0_AL/SPT1_AD1
1
PC_00/CAN0_TX/SPT1_BTDV/UART1_TX/SMC0_A04 66
PA_00/PWM0_SYNC/SPT1_ACLK
21PA_01/PWM0_TRIP0/SPT1_AFS
R46
0402
R47
0402
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG
JTG_TRST_CONN
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS
0
TRACE_D01/JTG_TRST
0
DNP
3.3V
R17
0402
R190
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD
0402
R191
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG
0402
R192
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM
0402
PB_04/PWM2_SYNC/UART0_RTS/SPT0_ATDV/SMC0_D12/CNT1_UD
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM
169
PD_00/SMC0_D08
PD_00/SMC0_D08
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD
166
PD_01/SMC0_D09
PD_01/SMC0_D09
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG
167
PD_02/SMC0_D10
PD_02/SMC0_D10
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM
163
PD_03/SMC0_D11
PD_03/SMC0_D11
160PB_04/PWM2_SYNC/UART0_RTS/SPT0_ATDV/SMC0_D12/CNT1_UD
164
PD_04/SMC0_D12
PD_04/SMC0_D12
156PB_05/PWM2_TRIP0/UART0_CTS/TM0_TMR7/SMC0_D13/CNT1_DG
161
PD_05/SMC0_D13
PD_05/SMC0_D13
155PB_06/PWM2_AH/TM0_CLK/SPI1_SEL2/SMC0_D14
146
PD_06/SMC0_D14
PD_06/SMC0_D14
154PB_07/PWM2_AL/TM0_TMR0/SPI1_SEL3/SMC0_D15
145
PD_07/SMC0_D15
PD_07/SMC0_D15
153PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2
142
PD_08/SMC0_A06
PD_08/SMC0_A06
152PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE
143
PD_09/SMC0_A07
PD_09/SMC0_A07
PB_10/SINC0_CLK0/SPI0_D2/CAN1_RX/SMC0_AWE/TM0_ACI1
151PB_10/SINC0_CLK0/SPI0_D2/CAN1_RX/SMC0_AWE/TM0_ACI1
140
PD_10/SMC0_A08
PD_10/SMC0_A08
PB_11/SINC0_D0/SPI0_D3/CAN1_TX/SMC0_AMS0/TM0_ACLK1
80PB_11/SINC0_D0/SPI0_D3/CAN1_TX/SMC0_AMS0/TM0_ACLK1
141
PD_11/SMC0_A09
PD_11/SMC0_A09
81PB_12/SINC0_D1/SPT0_BTDV/UART2_RX/SMC0_AOE/TM0_ACI3
138
PD_12/SMC0_A10
PD_12/SMC0_A10
78PB_13/SINC0_D2/CNT0_OUTA/SPI0_SEL2/SMC0_A01/TM0_ACLK0/SYS_DSWAKE3
139
PD_13/SMC0_A11
PD_13/SMC0_A11
76PB_14/SINC0_D3/CNT0_OUTB/SPI0_SEL3/SMC0_A02/SPI0_SS/SYS_DSWAKE2
135
PD_14/SMC0_A12
77PB_15/CAN0_RX/SPT1_ATDV/UART1_RX/SMC0_A03/TM0_ACI4
134
PD_15/SMC0_A13
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM
PB_05/PWM2_TRIP0/UART0_CTS/TM0_TMR7/SMC0_D13/CNT1_DG
PB_06/PWM2_AH/TM0_CLK/SPI1_SEL2/SMC0_D14
PB_07/PWM2_AL/TM0_TMR0/SPI1_SEL3/SMC0_D15
PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2
PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE
2
PB_12/SINC0_D1/SPT0_BTDV/UART2_RX/SMC0_AOE/TM0_ACI3
PB_13/SINC0_D2/CNT0_OUTA/SPI0_SEL2/SMC0_A01/TM0_ACLK0/SYS_DSWAKE3
PB_14/SINC0_D3/CNT0_OUTB/SPI0_SEL3/SMC0_A02/SPI0_SS/SYS_DSWAKE2
PB_15/CAN0_RX/SPT1_ATDV/UART1_RX/SMC0_A03/TM0_ACI4
0
171
0
168
0
162
0
159
JTAG/SWD
R5
10K
0402
DNP
R4
10K
0402
DNP
R3
10K
0402
DNP
R2
10K
0402
JTG_TRST_CONN
JTG_TDI
JTG_TMS/SWDIO
P1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PD_14/SMC0_A12
17
18
PD_15/SMC0_A13
19
JTG_TCK/SWCLK
JTG_TDO/SWO
JTAG_BOARD_RESET
ADSP-CM408BSWZ
QFPS50P2600X2600X160-178N
2
20
TE_5103308-5
R194
10K
0402
R195
10K
0402
3.3V
3.3V
JTG_TRST_CONN
U1
3
PE_00/SMC0_A14
133
PE_00/SMC0_A14
71
PF_00/ETH0_RXD0/CNT0_OUTA
PF_00/ETH0_RXD0/CNT0_OUTA
PE_01/SMC0_A15
130
PE_01/SMC0_A15
70
PF_01/ETH0_RXD1/CNT0_OUTB
PF_01/ETH0_RXD1/CNT0_OUTB
PE_02/SMC0_A16
127
PE_02/SMC0_A16
69
PF_02/USB0_VBC/TRACE_D03
PE_03/SMC0_A17
126
PE_03/SMC0_A17
PF_03/SMC0_AOE68
PE_04/SMC0_A18
92
PE_04/SMC0_A18
67
PF_04/SMC0_ARDY
PE_05/SMC0_A19
91
PE_05/SMC0_A19
61
PF_05/SMC0_A01
PF_05/SMC0_A01
PE_06/SMC0_A20
90
PE_06/SMC0_A20
58
PF_06/SMC0_A02
PF_06/SMC0_A02
89
PE_07/ETH0_PTPAUXIN/SMC0_A21
59
PF_07/SMC0_A03
PF_07/SMC0_A03
88
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
55
PF_08/SMC0_A04
PF_08/SMC0_A04
87
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
56
PF_09/SMC0_A05
PF_09/SMC0_A05
PE_07/ETH0_PTPAUXIN/SMC0_A21
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
85PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG
84
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
82PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
75PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
74
PE_14/ETH0_TXEN/CNT1_OUTA
PE_14/ETH0_TXEN/CNT1_OUTA
53
PF_10/ETH0_PTPCLKIN
JTG_TMS/SWDIO
R193
0402
0
SMC0_AMS0
USB0_DP
USB0_DP
34
USB0_DM
USB0_DM
37
USB0_ID
USB0_ID
JTG_TDI
JTG_TDO/SWO
R6
0402
0
JTG_TRST
R8
0402
29
SYS_XTAL
27
SYS_HWRST
132
SYS_NMI
4
26
SYS_FAULT
24
SYS_RESOUT
U34
0
1
TWI0_SCL
TP1
3
OUT
SYS_CLKIN
C3
18PF
0402
DNP
SYS_CLKIN
33
SYS_CLKOUT
ANALOG
DEVICES
C2
0.01UF
0402
SYS_RESOUT
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-CM408F EZ-KIT
PROCESSOR, JTAG/SWD AND TRACE CONN, CLOCK
Size
Board No.
Date
C
Rev
A0341-2012
C
B
20 Cotton Road
Title
ADSP-CM408BSWZ
QFPS50P2600X2600X160-178N
A
C4
18PF
0402
DNP
TP12
SYS_HWRST
SYS_FAULT
R11
0
0402
DNP
SYS_XTAL
SYS_XTAL
SYS_NMI
Y1
30MHZ
OSC013
DNP
3.3V
SYS_CLKIN
R7
0402
OE
R12
0
0402
DNP
R9
33
0402
4
VDD
GND
30MHZ 2
OSC012
TWI0_SDA
SYS_BMODE1
46
JTG_TRST
DSP OSC
R10
10K
0402
USB0_VBUS
SYS_BMODE0
174
SYS_CLKOUT
3
C153
0.1UF
0402
route as differential pair
175
SYS_BMODE1
SYS_CLKIN
3.3V
DNP
3.3V
48
JTG_TMS/SWDIO
47
JTG_TDO/SWO
SN74LVC1G08
SOT23-5
OPTIONAL DSP CRYSTAL
176
SYS_BMODE0
30
C1
0.1UF
0402
JTG_TRST
3.3V
45
JTG_TCK/SWCLK
44
JTG_TDI
U48
PF_10/ETH0_PTPCLKIN
147
SMC0_AMS0
43
TWI0_SDA
R197
10K
0402
DNP
4
PF_04/SMC0_ARDY
SMC0_AWE
42
TWI0_SCL
1
JTG_TRST
2
JTG_TRST_CONN
PF_03/SMC0_AOE
148
SMC0_AWE
36
USB0_VBUS
JTG_TCK/SWCLK
SYS_HWRST
SMC0_ARE
35
0
PF_02/USB0_VBC/TRACE_D03
149
SMC0_ARE
73
PE_15/ETH0_REFCLK/CNT1_OUTB
PE_15/ETH0_REFCLK/CNT1_OUTB
R198
0402
0.2A
Sheet
07/02/2013
D
2
of
13
A
97
98 ADC1_VIN00
99 ADC1_VIN01
100 ADC1_VIN02
101 ADC1_VIN03
102 ADC1_VIN04
103 ADC1_VIN05
104 ADC1_VIN06
ADC1_VIN07
BYP_A0
BYP_A1
BYP_D0
REFCAP
112
VREF0 108
VREF1 111
GND_VREF0 109
GND_VREF1
J9
3.3V
R15
0
0805
VREF0
VREF1
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
ADC0_VIN00_EXP_CONN
115
VDD_ANA0 105
VDD_ANA1
ADC0_VIN02
114
GND_ANA0 106
GND_ANA1 124
GND_ANA2 96
GND_ANA3
R229
0402
ADC0_VIN04
0
ADC0_VIN06
AGND
ADC1_VIN07
ADSP-CM408BSWZ
QFPS50P2600X2600X160-178N
ADC1_VIN05
ADC1_VIN03
R230
0402
ADC1_VIN01
0
AGND
5V
3.3V
VREF_BUFFERED
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
121
ADC1_VIN00
ADC1_VIN01
ADC1_VIN02
ADC1_VIN03
ADC1_VIN04
ADC1_VIN05
ADC1_VIN06
ADC1_VIN07
113
BYP_A0 107
BYP_A1 95
BYP_D0 110
REFCAP
122
U1
123
122 ADC0_VIN00
121ADC0_VIN01
120 ADC0_VIN02
119 ADC0_VIN03
118 ADC0_VIN04
117 ADC0_VIN05
116 ADC0_VIN06
ADC0_VIN07
D
ADC
123
ADC0_VIN00
ADC0_VIN01
ADC0_VIN02
ADC0_VIN03
ADC0_VIN04
ADC0_VIN05
ADC0_VIN06
ADC0_VIN07
C
DAC
124
1
B
VREF
ADC0_VIN01
ADC0_VIN03
ADC0_VIN05
ADC0_VIN07
1
ADC1_VIN06
ADC1_VIN04
ADC1_VIN02
ADC1_VIN00_EXP_CONN
VREF_BUFFERED
U6
8
TP1
GND
0.0
R14
10K
0402
VREF0_ADR441
5
TRIM
1FEEDBACK
DISABLE8
2-IN
+VS7
24.9
3+IN
VOUT6
GND
R13
0402
BUFFER_IN
R204
10K
0603
DNP
4
R214
0402
0
VREF_BUFFERED
5
-VS1
9
-VS0
ADA4899
SOIC127P602X147-9N
AGND
2
3.3V
AGND
5V
5V
U47
C156
0.1UF
0402
1
4
AGND
VIN
6
VOUT
TP0
8
TP1
GND
125
126
127
128
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
U33
C17
0.1UF
0402
ADR441ARMZ
MSOP8
2
121
122
123
124
R203
0603
0.0
VREF1_ADR441
CT1
10UF
ELEC_4MM
C157
0.1UF
0402
5
TRIM
C34
0.1UF
0402
C9
0.01UF
0402
125
4
TP0
R16
0603
RESERVED
126
1
6
VOUT
127
C18
0.1UF
0402
VIN
128
2
2
5V
POWER
ADR441ARMZ
MSOP8
SAMTEC_QSH-060-F-D-A
R205
10K
0603
DNP
AGND
AGND
AGND
ANALOG CONN
AGND
VREF_BUFFERED
JP3
JP4
1
VREF0_ADR441
3
VREF0
IDC2X1
R199
0
0402
TP13
ADC0_VIN00_EXP_CONN
J10
SMC
AMPHENOL_152119
DNP
2
BUFFER_IN
2
VREF0_ADR441
P10
1
1
2
VREF0
AGND
3
IDC2X1
IDC3X1
ADC0_VIN00
R200
0
0402
DNP
3
C182
27PF
0402
DNP
ADC0_VIN00_SMC
JP1
1
VREF1_ADR441
2
VREF1
AGND
IDC2X1
SJ2
SHORTING
JUMPER
DEFAULT=UNINSTALLED
SJ1
SHORTING
JUMPER
DEFAULT=1 & 2
R202
0
0402
AGND
ADC1_VIN00_EXP_CONN
J11
SMC
AMPHENOL_152119
DNP
AGND
SJ6
SHORTING
JUMPER
DEFAULT=UNINSTALLED
R232
0
0402
ADC1_VIN00
R201
0
0402
DNP
C183
27PF
0402
DNP
ADC1_VIN00_SMC
3.3V
3.3V
AGND
BYP_D0
BYP_A1
VREF1
REFCAP
VREF0
BYP_A0
AGND
C12
1UF
0402
C11
10UF
0603
C5
0.1UF
0402
C13
10UF
0603
C15
10UF
0805
C155
0.1UF
0402
C6
0.1UF
0402
C16
10UF
0805
C154
0.1UF
0402
C14
10UF
0402
C10
10UF
0603
ANALOG
DEVICES
C7
0.1UF
0402
4
Pins 95center pad
Pins 105-106
AGND
AGND
AGND
Pins 107-106
Pins 108-109
Pins 110-109
AGND
Pins 112-111
AGND
AGND
Pins 113-114
Pins 115-114
Size
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
ANALOG CONN, POWER
Title
AGND
20 Cotton Road
0.2A
Sheet
07/02/2013
D
3
of
13
A
B
C
D
3.3V
VDD_EXT
VDD_INT
D4
R181
0
1206
DNP
U1
22
65 VDD_INT0
94 VDD_INT1
128 VDD_INT2
157 VDD_INT3
VDD_INT4
VDD_VREG
1
IN0
VDD_VREG
3
GND0
USB0_VBUS
5
IN2
VREG_BASE
31
VREG_BASE
1
R169
0
1206
DNP
1206
P3
1
VBUS
VDD_INT_PNP
VDD_INT
D5
2
USB0_DM
3
USB0_DP
1
IN0
DC137
10UF
0805
C138
0.1UF
0402
"USB"
177
D+
USB0_ID
4
ID
5
GND
6
SHELL
ADSP-CM408BSWZ
QFPS50P2600X2600X160-178N
CON052
R185
0
0402
1
R186
THERM
ESDA6V1SC
SOT95P280-6N
Q1
STD2805T4
TO228P972X240-3N
2
R177
0.0
0603
83
GND0 131
GND1
GND_PADDLE
C142
4.7UF
0805
IN3
3
3.3V
R184
0
0402
DNP
GND1
6
R170
1K
0603
R176
0.0
0603
R178
0
0805
2
IN1
4
2
8 VDD_EXT0
15 VDD_EXT1
23 VDD_EXT2
28 VDD_EXT3
41 VDD_EXT4
50 VDD_EXT5
57 VDD_EXT6
64 VDD_EXT7
72 VDD_EXT8
79 VDD_EXT9
86 VDD_EXT10
93 VDD_EXT11
129 VDD_EXT12
136 VDD_EXT13
144 VDD_EXT14
150 VDD_EXT15
158 VDD_EXT16
165 VDD_EXT17
172 VDD_EXT18
137 VDD_EXT19
33 VDD_EXT20
125 VDD_EXT21
VDD_EXT22
1
32
USB_VBUS
0603
C141
0.01UF
0402
R179
1M
0603
3
GND0
4
IN2
8
GND1
5
IN3
R1
VARISTOR
VDD_EXT
2
IN1
FER3
600
1206
6
NC0
9
NC2
7
NC1
10
NC3
ESD7004
DFN50P250X100-10N
NOTE:
INTERNAL REGULATOR
C140
10UF
0603
2
C139
0.1UF
0402
NOTE: CONNECT PIN 131 DIRECTLY TO GROUND
REMOVE R177, R176, P6, R156, R163
FOR CUSTOMER DESIGNS
2
INSTALL R181, R169, R164
TP28
EXTERNAL REGULATOR
TP8
REMOVE R181, R169, R164
AGND
Pins 125-124
INSTALL R177, R176, P6, R156, R163
SYS_CLKOUT
SJ5
SHORTING
JUMPER
DEFAULT=INSTALLED
3.3V
TP10
1.2V @ 1.5A
"VDD_INT"
TP4
Remove P6 when measuring VDD_INT
3.3V
TP5
3.3V
TP6
3.3V
3.3V
5V
P6
1
R162
10
0603
L2
1.5UH
IND003
VIN
2
PVIN
TRK
C101
0.1UF
0402
D7
MBRS540T3G
SMC
8
PGOOD
R175
10K
0402
R180
10K
0402
C105
22UF
1210
C103
22UF
1210
R171
10K
0402
D2
GSOT03
SOT23-3
3
SYS_FAULT
R187
27K
0402
SYS_RESOUT
TWI0_SCL
SYS_NMI
TWI0_SDA
6
EN
FB
ADP2119ACPZ-R7
DFN50P300X300-11N
GND PGND
5
4
EPAD
11
SYS_HWRST
R164
0
0402
DNP
C133
10UF
0603
R174
10K
0402
R172
330.0
0402
R161
10K
0402
10
VDD_INT
R173
10K
0402
9
SYNC/MODE
C100
22UF
1210
VDD_INT
R160
0
0402
7
R163
0
0402
R156
0.05
1206
3
SW
3
4
LED8
RED
LED_0603
"FAULT"
VR1
1
C102
0.1UF
0402
2
IDC2X1
R159
0
0402
DNP
R188
27K
0402
JTG_TRST
TP16
R182
10K
0402
DNP
R183
4.7K
0402
DNP
VDD_EXT
C135
0.1UF
0402
C132
0.1UF
0402
C134
0.01UF
0402
C131
0.01UF
0402
C127
10UF
0603
C126
10UF
0603
C128
0.1UF
0402
C129
0.1UF
0402
C130
0.1UF
0402
C136
0.1UF
0402
C123
0.1UF
0402
C124
0.1UF
0402
C122
0.1UF
0402
C125
0.1UF
0402
C119
0.1UF
0402
C120
0.1UF
0402
C121
0.01UF
0402
C118
0.01UF
0402
C117
0.01UF
0402
C116
0.01UF
0402
C115
0.01UF
0402
C114
0.01UF
0402
C113
0.01UF
0402
C112
0.01UF
0402
C111
0.01UF
0402
ANALOG
DEVICES
C110
0.01UF
0402
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-CM408F EZ-KIT
DIGITAL POWER, VDDINT, USB
Board No.
Rev
A0341-2012
C
Date
20 Cotton Road
0.2A
Sheet
07/02/2013
D
4
of
13
A
B
C
D
TWI address 0100 000x
4Mb (256K x 16) SRAM
where x is the R/W bit. Read - 1, Write - 0
3.3V
U2
PF_05/SMC0_A01
PD_08/SMC0_A06
R30
10K
0402
DNP
PC_10/SPT0_BD0/SMC0_D02
B3
D2
D3
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03
8
SCL
GPA1
TWI0_SCL
B4
E2
D4
PC_12/SPI1_CLK/SMC0_D04
TWI0_SDA
9
SDA
GPA2
A4
C3
A5
F2
D5
PC_13/SPI1_MISO/SMC0_D05
5
VDD
PC_14/SPI1_MOSI/SMC0_D06
PD_10/SMC0_A08
D4
A7
G1
D7
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS
PD_11/SMC0_A09
H2
A8
B6
D8
PD_00/SMC0_D08
H3
A9
PD_13/SMC0_A11
H4
A10
PD_14/SMC0_A12
H5
A11
PD_15/SMC0_A13
G3
A12
D12
PE_00/SMC0_A14
G4
A13
D13
PE_01/SMC0_A15
F3
A14
PE_02/SMC0_A16
F4
A15
PE_03/SMC0_A17
D11
D14
D15
16
15
C5
D5
E5
PD_03/SMC0_D11
GPB1
R32
10K
0402
DNP
PD_04/SMC0_D12
F5
PD_05/SMC0_D13
F6
R37
10K
0402
DNP
R36
10K
0402
DNP
GPB2
GPB3
PD_06/SMC0_D14
G6
GPB4
11
PD_07/SMC0_D15
12
D3
A17
13
3.3V
CE
0
DNP
B2
18
19
20
1
UART0RTS_EN
21
UART0RX_EN
22
UART0CTS_EN
23
UART0CTS_RTS_LPBK
24
UART0CTS_RST_EN
A0
GPB5
A1
GPB6
A2
GPB7
25
CAN0_EN
26
PUSHBUTTON1_EN
27
PUSHBUTTON2_EN
28
LED1_GPIO1_EN
1
LED2_GPIO2_EN
2
LED3_GPIO3_EN
3
LED4_GPIO4_EN
4
MCP23017
QFN65P600X600-29N
G5
WE
A2
GPA6
INTB
GPB0
E4
0
GPA5
INTA
PD_02/SMC0_D10
B5
R49
0402
R48
0402
GPA4
17
PD_01/SMC0_D09
A16
PE_04/SMC0_A18
RESET
GPA7
C6
D9
D10
14
SYS_HWRST
F1
D6
PD_12/SMC0_A10
GPA0
GPA3
C4
A6
SMC0_AWE
SMC0_ARE
C2
D2
U40
PD_09/SMC0_A07
SMC0_AMS0
PF_03/SMC0_AOE
A5
A3
PF_09/SMC0_A05
R31
10K
0402
DNP
PC_09/SPT0_BFS/SMC0_D01
A2
PF_08/SMC0_A04
R29
10K
0402
PC_08/SPT0_BCLK/SMC0_D00
C1
D1
A1
PF_07/SMC0_A03
3.3V
B1
D0
A4
A0
PF_06/SMC0_A02
1
A3
R34
10K
0402
OE
BHE
C143
0.1UF
0402
A1
BLE
R33
10K
0402
R35
10K
0402
3.3V
C144
0.01UF
0402
C20
0.01UF
0402
CY7C1041CV33
BGA48_75_810
R20
10K
0402
2
R27
10K
0402
2
SOFTCONFIG
TWI address 0100 010x
3.3V
where x is the R/W bit. Read - 1, Write - 0
3.3V
U41
5
17
GPA0
RS485_RE
8
18
GPA1
RS485_DE
9
19
GPA2
CAN1_EN
20
GPA3
ETH0_MDIO_BUS_EN
21
GPA4
ETHERNET_EN
22
GPA5
PHYINT_EN
INTA
23
GPA6
RMII_CLK_EN
INTB
24
GPA7
WAKE_PUSHBUTTON_EN
U4
25
GPB0
DATA_LOW_EXP_EN
OE
26
GPB1
DATA_HIGH_EXP_EN
27
GPB2
TRACE_EXP_EN
28
GPB3
PB_08_09_EXP_EN
1
GPB4
ETH_EXP_EN
A0
2
GPB5
SRAM_BYTE_EN
A1
3
GPB6
A2
4
GPB7
VDD
TWI0_SCL
R28
10K
0402
SCL
TWI0_SDA
SDA
14
SYS_HWRST
RESET
U7
SRAM_BYTE_EN
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
1
2
16
OE
A
4
15
B
PI3A125
SC70_5
1
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
3
2
A
4
R41
10K
0402
DNP
B
PI3A125
SC70_5
R38
10K
0402
R39
10K
0402
DNP
11
3.3V
12
13
3
MCP23017
QFN65P600X600-29N
C19
0.01UF
0402
R43
10K
0402
C8
0.01UF
0402
R42
10K
0402
DNP
3.3V
R40
10K
0402
C21
0.01UF
0402
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-CM408F EZ-KIT
MEMORY AND SOFTCONFIG
Board No.
Rev
A0341-2012
C
Date
20 Cotton Road
0.2A
Sheet
07/02/2013
D
5
of
13
A
B
3.3V
C
3.3V
3.3V
D
3.3V
U11
U12
R220
10K
0402
DNP
1
R222
10K
0402
9
3VCCB1
13VCCB0
VCCB2
15
VCCA019
VCCA125
VCCA2
1
2B1
4B2
5B3
7B4
8B5
10B6
11B7
B8
PC_08/SPT0_BCLK/SMC0_D00
PC_09/SPT0_BFS/SMC0_D01
PC_10/SPT0_BD0/SMC0_D02
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03
PC_12/SPI1_CLK/SMC0_D04
PC_13/SPI1_MISO/SMC0_D05
PC_14/SPI1_MOSI/SMC0_D06
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS
R219
10K
0402
DNP
27
A126
A224
A323
A421
A520
A618
A717
A8
R223
10K
0402
R221
10K
0402
27
A126
A224
A323
A421
A520
A618
A717
A8
PD_00/SMC0_D08_EXP
PD_01/SMC0_D09_EXP
PD_02/SMC0_D10_EXP
PD_03/SMC0_D11_EXP
PD_04/SMC0_D12_EXP
PD_05/SMC0_D13_EXP
PD_06/SMC0_D14_EXP
PD_07/SMC0_D15_EXP
1
29
14OE1
30OE2
31OUT_SEL
TEST_EN
R217
10K
0402
PI4ULS3V08M
QFN40P300X600X75-33N
15
VCCA019
VCCA125
VCCA2
1
2B1
4B2
5B3
7B4
8B5
10B6
11B7
B8
DATA_HIGH_EXP_EN
22
GND328
GND432
GND533
EPAD
6
12GND0
16GND1
GND2
R218
10K
0402
PD_00/SMC0_D08
PD_01/SMC0_D09
PD_02/SMC0_D10
PD_03/SMC0_D11
PD_04/SMC0_D12
PD_05/SMC0_D13
PD_06/SMC0_D14
PD_07/SMC0_D15
PC_08/SPT0_BCLK/SMC0_D00_EXP
PC_09/SPT0_BFS/SMC0_D01_EXP
PC_10/SPT0_BD0/SMC0_D02_EXP
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03_EXP
PC_12/SPI1_CLK/SMC0_D04_EXP
PC_13/SPI1_MISO/SMC0_D05_EXP
PC_14/SPI1_MOSI/SMC0_D06_EXP
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS_EXP
29
14OE1
30OE2
31OUT_SEL
TEST_EN
DATA_LOW_EXP_EN
9
3VCCB1
13VCCB0
VCCB2
22
GND328
GND432
GND533
EPAD
6
12GND0
16GND1
GND2
R216
10K
0402
PI4ULS3V08M
QFN40P300X600X75-33N
3.3V
3.3V
3.3V
3.3V
C169
0.01UF
0402
C168
0.01UF
0402
C167
0.01UF
0402
C164
0.01UF
0402
C165
0.01UF
0402
C166
0.01UF
0402
C161
0.01UF
0402
C162
0.01UF
0402
C163
0.01UF
0402
C158
0.01UF
0402
C159
0.01UF
0402
C160
0.01UF
0402
2
2
3.3V
3.3V
R224
10K
0402
R225
10K
0402
U57
TRACE_EXP_EN
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM
ETH_EXP_EN
U55
1
OE
2
A
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
B
4
1
OE
2
A
4
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD_EXP
4
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG_EXP
B
PI3A125
SC70_5
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM_EXP
PI3A125
SC70_5
U60
1
OE
U54
1
OE
3
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD
2
A
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
B
4
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD_EXP
OE
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
B
4
2
A
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG_EXP
U58
3.3V
OE
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM
B
4
2
A
4
B
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM_EXP
PI3A125
SC70_5
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM_EXP
U56
1
OE
3.3V
U51
1
OE
2
A
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD_EXP
1
PI3A125
SC70_5
PF_02/USB0_VBC/TRACE_D03
4
B
PI3A125
SC70_5
U52
1
OE
2
A
3
U59
PI3A125
SC70_5
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM
B
1
U53
1
OE
2
A
A
PI3A125
SC70_5
PI3A125
SC70_5
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG
2
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG
B
4
2
A
4
B
C179
0.1UF
0402
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG_EXP
C178
0.01UF
0402
C177
0.01UF
0402
C176
0.01UF
0402
C175
0.01UF
0402
PI3A125
SC70_5
USB0_VBC
PI3A125
SC70_5
3.3V
R215
10K
0402
3.3V
U49
PB_08_09_EXP_EN
C174
0.1UF
0402
C173
0.01UF
0402
C172
0.01UF
0402
C171
0.01UF
0402
PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2
C170
0.01UF
0402
OE
2
A
4
B
ANALOG
DEVICES
PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2_EXP
PI3A125
SC70_5
C180
0.01UF
0402
4
1
C181
0.01UF
0402
U50
1
OE
PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE
2
A
4
B
PI3A125
SC70_5
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
SOFTCONFIG
Title
PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE_EXP
Size
20 Cotton Road
0.2A
Sheet
07/02/2013
D
6
of
13
A
B
C
D
RS485_V+
3.3V
20 X 2 Character Display
RS-485
3.3V
5V
5V
U39
2
R18
10K
0402
1
C23
10UF
0805
J5
2
TWI0_SDA_DISPLAY
C22
0.1UF
0402
3
6
5
8
7
10
VCC0
7
VCC1
10
VISOOUT
RS485_V+
J2
R44
120.0
0603
15
VISOIN
R207
1.0K
0603
DNP
1
1
6
4
RS485_RE
1
4
R50
1.0K
0603
DNP
RE
PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2
RXD
7
12
DE
3
Z
6
PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE
2
14
A
5
RS485_DE
13
B
3
TXD
Y
11
8
TWI0_SCL_DISPLAY
4
9
IDC5X2_SMT_F
R19
10K
0402
1
8GND1_0
GND1_1
9
GND2_016
GND2_1
9
R206
1.0K
0603
DNP
ADM2682E
SOIC127P1032X265-16N
TWI address 1010 000x
R208
1.0K
0603 RS485_V+
DNP
5
CON038
DB9
where x is the R/W bit. Read - 1, Write - 0
GND2
GND2
5V
3.3V
3.3V
GND2
RS485_V+
3.3V
R209
200.0K
0402
R210
680
0402
C30
0.01UF
0402
R211
680
0402
C29
0.1UF
0402
C28
10UF
0805
RS485_V+
C31
0.1UF
0402
C27
10UF
0805
C26
0.1UF
0402
C24
0.01UF
0402
C25
0.1UF
0402
U10
2
1
GND
2
SREF
3
TWI0_SCL
S1
4
TWI0_SDA
S2
2
GREF
DREF
D1
D2
8
7
6
TWI0_SCL_DISPLAY
5
GND2
TWI0_SDA_DISPLAY
Place close to pins 7 and 8
GND2
Place close to pins 1 and 2
Place close to pins 9 and 10
Place close to pins 15 and 16
GTL2002
TSSOP8
3.3V
C32
0.01UF
0402
C33
0.01UF
0402
BOOT MODE
BOOT MODE SWITCH (SW1)
3.3V
BOOT MODE (1:0)
3
00
01
10
11
C
No Boot
SPI Master Boot (internal SPI2)
SPI Slave Boot (SPI0)
UART Boot (UART0)
3
SW1
1
2
1
3
0
2
4
7
6
SYS_BMODE0
SYS_BMODE1
4
5
SWT027
ROTARY
R87
10K
0402
ANALOG
DEVICES
4
Title
Size
A
B
C
R88
10K
0402
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-CM408F EZ-KIT
RS-485, ROTARY, DISPLAY AND BOOT CONN
Board No.
Rev
A0341-2012
C
Date
R81
10K
0402
0.2A
Sheet
07/02/2013
D
7
of
13
A
B
C
D
3.3V
1
1
U36
A2
B1VCC0
B2VCC1
VCC2
3.3V
A10
VISO0B10
VISO1C10
VISO2
C36
0.1UF
0402
R52
10K
0402
UART0RTS_EN
2
PB_04/PWM2_SYNC/UART0_RTS/SPT0_ATDV/SMC0_D12/CNT1_UD
G11
C2+
G10
C2-
OE
PC_02/UART0_TX/TRACE_D03/SPI0_RDY
4
A
B
D1
F1TIN1
TIN2
C38
0.10UF
0402
E11
C1-
U13
1
RS-232
C11
C1+
R53
10K
0402
C40
0.1UF
0402
C37
0.10UF
0402
B11
V+
R51
10K
0402
DNP
C42
10UF
0805
J3
GND3
D11
TOUT1F11
TOUT2
1
6
PI3A125
SC70_5
2
R60
0402
R59
0402
U14
1
UART0RX_EN
2
PC_01/UART0_RX/SMC0_A05/TM0_ACI5
33
33
C1
C2GND0
D2GND1
E1GND2
E2GND3
F2GND4
G1GND5
G2GND6
H2GND7
J1GND8
J2GND9
K2GND10
L2GND11
GND12
4
B
PI3A125
SC70_5
2
3.3V
R54
10K
0402
R55
10K
0402
C41
10UF
0805
3.3V
H11
RIN1K11
RIN2
7
3
OE
A
H1
K1ROUT1
ROUT2
C43
0.1UF
0402
C35
0.1UF
0402
8
J11
V-
4
D10
GND_ISO0E10
GND_ISO1F10
GND_ISO2H10
GND_ISO3J10
GND_ISO4K10
GND_ISO5L10
GND_ISO6
5
C39
0.10UF
0402
R57
10K
0402
CON038
DB9
ADM3252E
BGA44C100P11X11_1200X1200X103
GND3
GND3
R56
10K
0402
2
9
GND3
R58
10K
0402
U15
1
OE
UART0CTS_EN
2
A
PB_05/PWM2_TRIP0/UART0_CTS/TM0_TMR7/SMC0_D13/CNT1_DG
4
B
PI3A125
SC70_5
U16
1
OE
UART0CTS_RTS_LPBK
3
2
A
3
4
B
PI3A125
SC70_5
U17
1
OE
UART0CTS_RST_EN
2
A
CTS
4
B
PI3A125
SC70_5
3.3V
C150
0.1UF
0402
C149
0.1UF
0402
C148
0.1UF
0402
C151
0.01UF
0402
C152
0.01UF
0402
ANALOG
DEVICES
4
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
RS-232
Title
Size
20 Cotton Road
0.2A
Sheet
07/02/2013
D
8
of
13
A
B
C
D
CAN0_VISO
3.3V
5V
CAN0_VISO
CAN0_CANH
R212
0
0402
DNP
U38
8
VCC
19
VISOIN
R69
60.4
0603
6
VIO
VISOOUT
U19
1
CAN0_EN
OE
2
PC_00/CAN0_TX/SPT1_BTDV/UART1_TX/SMC0_A04
4
A
1
B
PI3A125
SC70_5
5
TXD
CAN0_RX
4
RXD
RS
1
1
3GND1_0
7GND1_1
9GND1_2
10GND1_3
GND1_4
OE
2
PB_15/CAN0_RX/SPT1_ATDV/UART1_RX/SMC0_A03/TM0_ACI4
4
A
B
PI3A125
SC70_5
1
2
14 CAN0_VREF R62
0402
17
CANH15
CANL
U18
J7
12
0
VREF
CAN0_TX
R72
10
0603
3
1
4
18
R68
60.4
0603
11
GND2_013
GND2_116
GND2_220
GND2_3
C52
4700PF
0603
R67
10K
0402
CON039
RJ11
R73
10
0603
CAN0_CANL
ADM3053
SOIC127P1032X265-20N
R70
10K
0402
3.3V
3.3V
5V
CAN0_VISO
CAN0_VISO
GND4
C62
0.1UF
0402
C49
0.01UF
0402
C56
0.1UF
0402
C57
10UF
0805
C63
0.1UF
0402
C53
0.01UF
0402
CAN0
C55
0.1UF
0402
C54
0.1UF
0402
C51
0.01UF
0402
GND4
2
Place between pins 6 and 7
Place between pins 8 and 9
C50
0.1UF
0402
GND4
Place between pins 11 and 12
2
Place between pins 19 and 20
CAN1_VISO
3.3V
5V
CAN1_VISO
CAN1_CANH
R213
0
0402
DNP
U37
8
19
VISOIN
VCC
R64
60.4
0603
6
VIO
12
VISOOUT
U21
1
OE
CAN1_EN
2
A
PB_11/SINC0_D0/SPI0_D3/CAN1_TX/SMC0_AMS0/TM0_ACLK1
4
B
CAN1_TX
CAN1_RX
5
VREF
4
17
CANH15
CANL
TXD
RXD
1
3GND1_0
7GND1_1
9GND1_2
10GND1_3
GND1_4
4
B
PI3A125
SC70_5
CAN1_VREF
R63
0402
0
3
4
R65
60.4
0603
11
GND2_013
GND2_116
GND2_220
GND2_3
C44
4700PF
0603
R66
10K
0402
R61
10
0603
CON039
RJ11
CAN1_CANL
ADM3053
SOIC127P1032X265-20N
R71
10K
0402
3
1
18
RS
U20
1
OE
2
A
J8
2
14
PI3A125
SC70_5
PB_10/SINC0_CLK0/SPI0_D2/CAN1_RX/SMC0_AWE/TM0_ACI1
R74
10
0603
3
3.3V
3.3V
5V
CAN1_VISO
CAN1_VISO
GND5
C64
0.1UF
0402
C61
0.01UF
0402
C59
0.1UF
0402
C58
10UF
0805
C65
0.1UF
0402
C46
0.01UF
0402
C60
0.1UF
0402
C45
0.1UF
0402
C47
0.01UF
0402
C48
0.1UF
0402
CAN1
GND5
Place between pins 6 and 7
Place between pins 8 and 9
Place between pins 11 and 12
GND5
Place between pins 19 and 20
ANALOG
DEVICES
4
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
CAN0 AND CAN1
Title
Size
20 Cotton Road
0.2A
Sheet
07/02/2013
D
9
of
13
A
B
C
D
3.3V
3.3V
"SPEED"
3.3V
LED6
GREEN
LED_0603
3.3V
3.3V
U32
VCC
2
PF_00/ETH0_RXD0/CNT0_OUTA
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
3
PF_01/ETH0_RXD1/CNT0_OUTB
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
4
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
5
6
PE_14/ETH0_TXEN/CNT1_OUTA
7
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
18
A1
8
9
R90
0402
R98
0402
R89
0402
R92
0402
R93
0402
R155
0402
17
16
15
14
13
49.9
49.9
49.9
49.9
49.9
49.9
30
ETH0_MDIO_Z
ETH0_RXD0_Z
31
ETH0_MDC_Z
ETH0_RXD1_Z
46
PHYAD4
ETH0_TXD0_Z
45
PHYAD3
ETH0_TXD1_Z
44
ETH0_RXD1_Z
ETH0_TXEN_Z
43
ETH0_RXD0_Z
ETH0_CRS_Z
12
PHYAD0
11
MII_MODE
42
39
38
41
1
19
ETHERNET_EN
OE
ETH0_TXEN_Z
10
GND
SN74CB3Q3245
TSSOP20
2
3
ETH0_TXD0_Z
4
ETH0_TXD1_Z
3.3V
5
6
SNI_MODE
40
ETH0_CRS_Z
TXP
MDIO
TXN
MDC
RXP
RXD3/PHYAD4
RXN
RXD0/PHYAD1
LED_LINK/AN0
COL/PHYAD0
LED_SPEED/AN1
RX_DV/MII_MODE
LED_ACT/AN_EN
RX_ER/MDIX_EN
TCK
TX_CLK
TDO
TX_EN
TMS
TXD0
TRST
TXD1
TDI
TXD2
RESERVED1
TXD3/SNI_MODE
RESERVED2
U22
1
16
2
14
3
13
4
C78
0.1UF
0402
28
C79
0.1UF
0402
6
7
27
8
26
9
8
9
PFBOUT
PWR_DOWN/INT
PFBIN1
X1
LED1
11
LED2
12
10
R107
107.0
0805
11
13
SHIELD1
14
SHIELD2
12
CON065
R101
107.0
0805
20
21
24
2
23
18
AGND2
37
C72
0.1UF
0402
R82
4.87K
0402
19
15
25MHZ_OUT
AGND1
PFBIN2
X2
10
C67
0.1UF
0402
C68
0.1UF
0402
C77
10UF
0805
R80
2.21K
0603
OE
2
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM
RESET
DP83848
LQFP48
1
ETH0_MDIO_BUS_EN
R106
165.0
0603
SHGND2
RBIAS
DGND
R100
10K
0402
R102
165.0
0603
CRS/CRS_DV/LED_CFG
36
25
R103
49.9
0402
RX_CLK
IOGND2
33
R104
49.9
0402
17
RXD1/PHTAD2
IOGND1
34
PHY_CLKIN
R105
49.9
0402
5
47
7
PHY_PWR_DWN_INT
R96
49.9
0402
RXD2/PHYAD3
35
29
SYS_HWRST
C73
0.01UF
0402
R84
2.21K
0603
J1
3.3V
2
R78
2.21K
0603
1
22
AVDD
48
IOVDD2
U43
20
1
32
IOVDD1
R77
220.0
0603
R94
10K
0402
4
A
B
ETH0_MDC_Z
PI3A125
SC70_5
U23
1
3.3V
OE
3.3V
2
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG
4
A
B
3.3V
ETH0_MDIO_Z
PI3A125
SC70_5
P8
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
3.3V
R83
10K
0402
PE_07/ETH0_PTPAUXIN/SMC0_A21
R95
10K
0402
1
2
3
4
5
6
PF_10/ETH0_PTPCLKIN
IDC3X2_SMT
R108
2.21K
0603
PHY Address is 00001
U24
PHYINT_EN
3
C74
0.01UF
0402
PC_06/SPI0_SEL1/PWM2_DL/SYS_DSWAKE0
C76
0.01UF
0402
1
2
OE
3.3V
A
B
4
3
PHY_PWR_DWN_INT
PHYAD4
PI3A125
SC70_5
PHYAD3
ETH0_RXD1_Z
C71
0.01UF
0402
ETH0_RXD0_Z
PHYAD0
3.3V
3.3V
3.3V
R112
2.21K
0603
3.3V
R111
2.21K
0603
R110
2.21K
0603
R109
2.21K
0603
3.3V
R75
10K
0402
DNP
PHY OSC
U35
OE
GND
50MHZ 2
OSC012
R79
10K
0402
TP3
C70
0.01UF
0402
R91
1.50K
0402
R76
33
0402
4
VDD
1
RMII_CLK_EN
C66
0.01UF
0402
3
OUT
C75
0.01UF
0402
C69
0.01UF
0402
R86
2.21K
0603
PHY_CLKIN
ETH0_MDIO_Z
OSC
R99
33
0402
MII_MODE
SNI_MODE
PE_15/ETH0_REFCLK/CNT1_OUTB
ANALOG
DEVICES
R97
0
0805
4
R85
2.21K
0603
Size
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
ETHERNET
Title
SHGND2
20 Cotton Road
0.2A
Sheet
07/02/2013
D
10
of
13
A
B
C
D
PA_03/PWM0_AL/SPT1_AD1
PA_06/PWM0_CH/SPT1_BD0
PA_07/PWM0_CL/SMC0_AMS2/SPT1_BD1
PA_10/PWM1_SYNC/SMC0_D02/TM0_ACLK3
PA_12/PWM1_AH/TM0_TMR4/SMC0_D04
PA_13/PWM1_AL/TM0_TMR5/SMC0_D05
PA_08/PWM1_CH/SMC0_D00/TM0_ACLK5
PC_09/SPT0_BFS/SMC0_D01
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03
PC_13/SPI1_MISO/SMC0_D05
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS
PD_01/SMC0_D09
PD_03/SMC0_D11
PD_05/SMC0_D13
PD_07/SMC0_D15
PA_09/PWM1_CL/SMC0_D01/TM0_ACLK4
PB_04/PWM2_SYNC/UART0_RTS/SPT0_ATDV/SMC0_D12/CNT1_UD
PB_06/PWM2_AH/TM0_CLK/SPI1_SEL2/SMC0_D14
PB_07/PWM2_AL/TM0_TMR0/SPI1_SEL3/SMC0_D15
PC_03/SPI0_CLK/PWM2_CH
PC_04/SPI0_MISO/PWM2_CL
182
PA_02/PWM0_AH/SPT1_AD0
181
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
PA_00/PWM0_SYNC/SPT1_ACLK
PWM
183
PF_05/SMC0_A01
PF_07/SMC0_A03
PF_09/SMC0_A05
PD_09/SMC0_A07
PD_11/SMC0_A09
PD_13/SMC0_A11
PD_15/SMC0_A13
PE_01/SMC0_A15
PE_03/SMC0_A17
PE_05/SMC0_A19
PE_07/ETH0_PTPAUXIN/SMC0_A21
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD_EXP
TWI0_SDA
PC_12/SPI1_CLK/SMC0_D04
PC_14/SPI1_MOSI/SMC0_D06
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS
PB_06/PWM2_AH/TM0_CLK/SPI1_SEL2/SMC0_D14
PC_02/UART0_TX/TRACE_D03/SPI0_RDY
PB_15/CAN0_RX/SPT1_ATDV/UART1_RX/SMC0_A03/TM0_ACI4
186
UART
TWI
SPI
GPIO
189
190
191
192
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS
PB_07/PWM2_AL/TM0_TMR0/SPI1_SEL3/SMC0_D15
PC_00/CAN0_TX/SPT1_BTDV/UART1_TX/SMC0_A04
PC_01/UART0_RX/SMC0_A05/TM0_ACI5
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM_EXP
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG_EXP
PB_04/PWM2_SYNC/UART0_RTS/SPT0_ATDV/SMC0_D12/CNT1_UD
PC_09/SPT0_BFS/SMC0_D01_EXP
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03_EXP
PD_00/SMC0_D08_EXP
PD_02/SMC0_D10_EXP
PD_04/SMC0_D12_EXP
PD_06/SMC0_D14_EXP
PE_02/SMC0_A16
PE_04/SMC0_A18
185
186
187
188
185
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
PB_10/SINC0_CLK0/SPI0_D2/CAN1_RX/SMC0_AWE/TM0_ACI1
PB_11/SINC0_D0/SPI0_D3/CAN1_TX/SMC0_AMS0/TM0_ACLK1
PB_13/SINC0_D2/CNT0_OUTA/SPI0_SEL2/SMC0_A01/TM0_ACLK0/SYS_DSWAKE3
PF_00/ETH0_RXD0/CNT0_OUTA
PF_03/SMC0_AOE
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM_EXP
SMC0_ARE
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG_EXP
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG_EXP
PE_15/ETH0_REFCLK/CNT1_OUTB
PC_11/SMC0_AMS3/SPT0_BD1/SMC0_D03
PB_04/PWM2_SYNC/UART0_RTS/SPT0_ATDV/SMC0_D12/CNT1_UD
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG_EXP
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
SYS_NMI
TWI0_SDA
SYS_HWRST
PC_12/SPI1_CLK/SMC0_D04_EXP
PC_14/SPI1_MOSI/SMC0_D06_EXP
PB_12/SINC0_D1/SPT0_BTDV/UART2_RX/SMC0_AOE/TM0_ACI3
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS_EXP
PB_06/PWM2_AH/TM0_CLK/SPI1_SEL2/SMC0_D14
TWI0_SCL
PC_13/SPI1_MISO/SMC0_D05
CNT
TWI
SPI
187
PC_07/SINC0_CLK1/UART2_TX/UART1_RTS/SYS_DSWAKE1
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
SINC
SPORT
189
190
191
192
188
SYS_CLKOUT
187
2
CONTROL
188
SMC0_AWE
PF_04/SMC0_ARDY
SMC0_AMS0
PA_07/PWM0_CL/SMC0_AMS2/SPT1_BD1
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD_EXP
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
185
181
182
183
184
184
DATA
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
186
182
ADDRESS
183
PC_08/SPT0_BCLK/SMC0_D00
PC_10/SPT0_BD0/SMC0_D02
PC_12/SPI1_CLK/SMC0_D04
PC_14/SPI1_MOSI/SMC0_D06
PD_00/SMC0_D08
PD_02/SMC0_D10
PD_04/SMC0_D12
PD_06/SMC0_D14
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
184
1
PF_06/SMC0_A02
PF_08/SMC0_A04
PD_08/SMC0_A06
PD_10/SMC0_A08
PD_12/SMC0_A10
PD_14/SMC0_A12
PE_00/SMC0_A14
PE_02/SMC0_A16
PE_04/SMC0_A18
PE_06/SMC0_A20
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM_EXP
J6
181
J4
GPIO
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
PA_01/PWM0_TRIP0/SPT1_AFS
PA_04/PWM0_BH/SPT1_BCLK
PA_05/PWM0_BL/SPT1_BFS
PB_00/PWM0_DH/TRACE_CLK/SPT0_ACLK/SMC0_D08/CNT0_ZM_EXP
1
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD_EXP
PA_11/PWM1_TRIP0/UART1_CTS/SMC0_D03/TM0_ACLK2
PA_14/PWM1_BH/TM0_TMR6/SMC0_D06
PA_15/PWM1_BL/TM0_TMR3/SMC0_D07
PB_02/PWM1_DH/TRACE_D01/SPT0_AD0/SMC0_D10/CNT0_DG_EXP
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM_EXP
PB_05/PWM2_TRIP0/UART0_CTS/TM0_TMR7/SMC0_D13/CNT1_DG
PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2_EXP
PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE_EXP
PC_05/SPI0_MOSI/PWM2_DH
PC_06/SPI0_SEL1/PWM2_DL/SYS_DSWAKE0
181
182
183
184
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
PC_07/SINC0_CLK1/UART2_TX/UART1_RTS/SYS_DSWAKE1
PB_12/SINC0_D1/SPT0_BTDV/UART2_RX/SMC0_AOE/TM0_ACI3
PB_14/SINC0_D3/CNT0_OUTB/SPI0_SEL3/SMC0_A02/SPI0_SS/SYS_DSWAKE2
PF_01/ETH0_RXD1/CNT0_OUTB
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD_EXP
PE_14/ETH0_TXEN/CNT1_OUTA
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM_EXP
PB_05/PWM2_TRIP0/UART0_CTS/TM0_TMR7/SMC0_D13/CNT1_DG
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
TWI0_SCL
PC_13/SPI1_MISO/SMC0_D05_EXP
2
PC_15/SPI1_SEL1/SMC0_D07/SPI1_SS_EXP
PB_07/PWM2_AL/TM0_TMR0/SPI1_SEL3/SMC0_D15
PB_01/PWM0_DL/TRACE_D00/SPT0_AFS/SMC0_D09/CNT0_UD_EXP
PB_03/PWM1_DL/TRACE_D02/SPT0_AD1/SMC0_D11/CNT1_ZM_EXP
PC_08/SPT0_BCLK/SMC0_D00_EXP
PC_10/SPT0_BD0/SMC0_D02_EXP
PB_12/SINC0_D1/SPT0_BTDV/UART2_RX/SMC0_AOE/TM0_ACI3
PD_01/SMC0_D09_EXP
PD_03/SMC0_D11_EXP
PD_05/SMC0_D13_EXP
PD_07/SMC0_D15_EXP
PE_03/SMC0_A17
PE_05/SMC0_A19
185
186
187
188
POWER
5V
3.3V
5V_INPUT
5V
3.3V
SYS_RESOUT
SYS_NMI
SAMTEC_QSH-090-F-D-A
189
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
TMR
190
PE_06/SMC0_A20
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
PE_10/ETH_MDIO/SMC0_AMS1/CNT2_DG
PE_12/ETH0_TXD0/SMC0_ABE0/CNT3_UD
PE_14/ETH0_TXEN/CNT1_OUTA
PF_00/ETH0_RXD0/CNT0_OUTA
PB_06/PWM2_AH/TM0_CLK/SPI1_SEL2/SMC0_D14
PB_08/PWM2_BH/TM0_TMR1/UART1_RX/SMC0_ARDY/TM0_ACI2_EXP
RESERVED
191
190
SYS
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
SYS
POWER
192
SYS_FAULT
191
5V
192
3.3V
3
189
RESERVED
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
PE_07/ETH0_PTPAUXIN/SMC0_A21
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
PE_11/ETH0_MDC/SMC0_A24/CNT3_ZM
PE_13/ETH0_TXD1/SMC0_ABE1/CNT3_DG
PE_15/ETH0_REFCLK/CNT1_OUTB
PF_01/ETH0_RXD1/CNT0_OUTB
PB_07/PWM2_AL/TM0_TMR0/SPI1_SEL3/SMC0_D15
PB_09/PWM2_BL/TM0_TMR2/UART1_TX/SMC0_ARE_EXP
3
3.3V
5V
5V_INPUT
SYS_FAULT
SYS_HWRST
SAMTEC_QSH-090-F-D-A
PA_01/PWM0_TRIP0/SPT1_AFS
PA_11/PWM1_TRIP0/UART1_CTS/SMC0_D03/TM0_ACLK2
PWM CONN
PB_05/PWM2_TRIP0/UART0_CTS/TM0_TMR7/SMC0_D13/CNT1_DG
ASYNCH CONN
PF_04/SMC0_ARDY
R226
10K
0402
R231
10K
0402
4
R227
10K
0402
ANALOG
DEVICES
R228
10K
0402
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
EXPANSION CONNECTORS
Title
Size
20 Cotton Road
0.2A
Sheet
07/02/2013
D
11
of
13
A
B
C
D
U28
1
LED1_GPIO1_EN
OE
2
PE_07/ETH0_PTPAUXIN/SMC0_A21
A
B
4
PI3A125
SC70_5
make these all yellow
U5
U27
1
LED2_GPIO2_EN
2
1A1
1Y1
4
1A2
1Y2
PI3A125
SC70_5
6
1A3
1Y3
U26
8
1A4
1Y4
OE
2
PE_06/SMC0_A20
A
1
B
4
18
16
3.3V
14
1
12
1
LED3_GPIO3_EN
OE
2
PE_05/SMC0_A19
A
11
B
4
13
PI3A125
SC70_5
15
U25
17
1
LED4_GPIO4_EN
9
2A1
2Y1
2A2
2Y2
7
LED4
YELLOW
LED_0603
5
2A3
2Y3
2A4
2Y4
LED3
YELLOW
LED_0603
LED2
YELLOW
LED_0603
POWER
LED7
GREEN
LED_0603
LED1
YELLOW
LED_0603
3
OE
2
PE_09/ETH0_CRS/SMC0_A23/CNT2_UD
A
B
4
1
OE1
PI3A125
SC70_5
19
3.3V
R126
10K
0402
R124
10K
0402
R127
10K
0402
R119
330.0
0402
OE2
R118
330.0
0402
R117
330.0
0402
R116
330.0
0402
R115
330.0
0402
IDT74FCT3244APY
SSOP20
R123
10K
0402
R125
10K
0402
R128
10K
0402
R120
10K
0402
R113
10K
0402
3.3V
LABEL "PB1"
R142
10K
0402
3.3V
R137
100
0402
R136
33
0402
U3
11
SW4
MOMENTARY
SWT024
U31
1
OE
10
4
B
PUSHBUTTON1_EN
2
A
PF_10/ETH0_PTPCLKIN
PI3A125
SC70_5
74LVC14A
SOIC14
C93
1UF
0402
2
LABEL "PB2"
C84
0.01UF
0402
R140
10K
0402
C87
0.01UF
0402
C85
0.01UF
0402
C86
0.01UF
0402
C83
0.01UF
0402
2
R141
10K
0402
R139
100
0402
R145
33
0402
U3
9
SW5
MOMENTARY
SWT024
U30
1
OE
8
4
B
PUSHBUTTON2_EN
2
A
PE_08/ETH0_PTPPPS/SMC0_A22/CNT2_ZM
PI3A125
SC70_5
74LVC14A
SOIC14
C94
1UF
0402
R134
10K
0402
3.3V
3.3V
3.3V
R114
10K
0402
R138
10K
0402
R133
10K
0402
3
JTAG_BOARD_RESET
R132
100
0402
R144
33
0402
U3
1
SW3
MOMENTARY
SWT024
C91
1UF
0402
R121
10K
0402
2
U29
CTS
1
OE
B
A
1
U46
R122
10K
0402
4
2
PC_06/SPI0_SEL1/PWM2_DL/SYS_DSWAKE0
4
1
U45
4
1
MR
8
RESET
4
PFI
7
RESET
2
PFO
SN74LVC1G08
SOT23-5
SW2
MOMENTARY
SWT024
LED5
RED
LED_0603
3
R129
10K
0402
R131
330.0
0402
U42
PI3A125
SC70_5
74LVC14A
SOIC14
R130
10K
0402
SN74LVC1G08
SOT23-5
WAKE_PUSHBUTTON_EN
2
"RESET"
SYS_HWRST
5
ADM708SARZ
SOIC8
3.3V
"RESET"
3.3V
3.3V
C89
0.01UF
0402
C90
0.01UF
0402
3.3V
3.3V
C88
0.01UF
0402
C81
0.01UF
0402
C82
0.01UF
0402
C80
0.01UF
0402
3.3V
R135
10K
0402
R143
10K
0402
U3
4
5
U3
6
74LVC14A
SOIC14
R189
10K
0402
3
U3
4
74LVC14A
SOIC14
ANALOG
DEVICES
13
12
74LVC14A
SOIC14
C92
0.01UF
0402
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-CM408F EZ-KIT
LEDS, PUSHBUTTONS AND RESET
Board No.
Rev
A0341-2012
C
Date
20 Cotton Road
0.2A
Sheet
07/02/2013
D
12
of
13
A
B
C
D
SJ7
SHORTING
JUMPER
DEFAULT=1&2
5V
JP2
1
WALL_POWER
3.3V
2
1
Remove P4 when measuring USB_VBUS
3
5V_INPUT
USB0_VBC
R151
0
0402
WALL_POWER
5V
5V
FER4
190
FER002
4
3
1
2
P4
7
IN1
USB_VBUS_EN
R150
0.05
1206
6
OUT1
8
OUT2
1
C98
10UF
1210
D6
MBRS540T3G
D1
GSOT05
CT2
150UF
D
SOT23-3
2
USB_VBUS
2
IDC2X1
1
C97
1000PF
1206
1
U44
P9
3
R152
10K
0402
DNP
TP9
USB_VBUS_EN
F1
3A
FUS004
1
SJ3
SHORTING
JUMPER
DEFAULT=INSTALLED
IDC3X1
2
FLG
GND
3 MIC2025-1
SOIC8
C96
1UF
0805
R153
10K
0402
DNP
TP15
EN
C95
1UF
0805
"USB_VBUS"
GND Test Points are scattered on PCB for Test Measurement Purposes.
LABEL "GND" ON ALL TPs
TP19 TP18 TP17 TP7
GP1
LOOP_2838
TP2
SMC
POWER
CON045
"5V"
FER1
600
1206
C99
1000PF
1206
FER2
600
1206
2
2
SHGND
SJ8
SHORTING
JUMPER
DEFAULT=INSTALLED
SHGND
P7
1
"3.3V"
3.3V
2
Remove P7 when measuring VDD_EXT
IDC2X1
R165
0.05
1206
3.3V @ 2A
TP11
5V
"VDD_EXT"
IDC2X1
R146
0
0402
R167
10
0603
L1
1.5UH
INDC4040X210N
VR2
14
VIN
11
SW010
SW19
SW2
13
12PVIN0
PVIN1
3
3
TRK
R147
0
0402
1
2
C106
22UF
1210
C107
22UF
1210
D3
GSOT03
SOT23-3
R148
10K
0402
FREQ
C109
0.1UF
0402
VDD_EXT
3
SJ4
SHORTING
JUMPER
DEFAULT=INSTALLED
16
15
EN
ADP2118ACPZ
5
QFN65P400X400X80-17N
6 7 8
EPAD
PGOOD
PGND0
PGND1
PGND2
R168
0
0402
GND
C108
22UF
1210
Remove P5 when measuring 3.3V
2
R154
0.05
1206
D8
MBRS540T3G
SMC
SYNC/MODE
C104
0.1UF
0402
P5
1
R157
45.3K
0402
4
FB
17
R149
0
0402
DNP
R166
0
0402
DNP
R158
10K
0402
TP27
ANALOG
DEVICES
4
Board No.
A
B
C
4
PH: 1-800-ANALOGD
Rev
A0341-2012
C
Date
Nashua, NH 03063
ADSP-CM408F EZ-KIT
POWER
Title
Size
20 Cotton Road
0.2A
Sheet
07/02/2013
D
13
of
13
I
INDEX
A
ADSP-CM408F processor, x
analog connector (J9), 2-26
architecture, of this EZ-KIT Lite, 2-2
asynch or memory connector (J4), 2-24
B
bill of materials, A-1
board schematic (ADSP-CM408F), B-1
bus switch, 2-5
example, 2-6
C
CAN0 connector (J7), 2-25
CAN1 connector (J8), 2-26
character display connector (J5), 2-25
configuration, of this EZ-KIT Lite, 1-3
connectors, 2-23
diagram of locations, 2-23
J1 (ethernet), 2-24
J2 (RS-485), 2-24
J3 (DCE UART), 2-24
J4 (asynch or memory), 2-24
J5 (character display), 2-25
J6 (PWM), 2-25
J7 (CAN0), 2-25
J8 (CAN1), 2-26
J9 (analog), 2-26
connectors
(continued)
P10 (VREF buffered), 2-27
P1 (JTAG/SWD/SWV), 2-26
P2 (RACE and JTAG/SWD), 2-26
P3 (USB), 2-27
P8 (IEEE 1588), 2-27
P9 (power), 2-27
contents, of this EZ-KIT Lite package, 1-2
D
DCE UART connector (J3), 2-24
debug interface, 1-13
default configuration, of this EZ-KIT Lite, 1-3
default jumper and switch settings, 1-4
default processor interface availability, 2-7
design reference information, 1-16
E
EngineerZone, xviii
ethernet connector (J1), 2-24
ethernet interface, 1-12
ethernet speed LED (LED6), 2-21
example programs, 1-16
expansion interface, 1-14
F
FET switches, 2-4
example, 2-4
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
I-1
Index
G
general-purpose I/O pins (GPIO), 2-21
I
IEEE 1588 (P8), 2-27
installation, of this EZ-KIT Lite, 1-4, 1-5
J
JTAG/SWD/SWV connector (P1), 2-26
jumpers
diagram of locations, 2-17
product overview, x
programming SoftConfig switches, 2-8
push buttons and switches, 2-15
PWM connector (J6), 2-25
R
reset LED (LED5), 2-21
RS-485 connector (J2), 2-24
S
mechanical switch, 2-5, 2-7
schematic, of ADSP-CM408F EZ-KIT Lite,
B-1
serial liquid crystal display module interface,
1-13
SoftConfig
on the EZ-KIT Lite, 2-7, 2-10
overview, 2-3
programming switches, 2-8
SRAM memory (U2), 1-8
supported tools, xvii
switches
programming SoftConfig, 2-8
switches, diagram of locations, 2-15
SYS_FAULT LED (LED8), 2-22
system architecture, of this EZ-KIT Lite, 2-2
N
T
notation conventions, xviii
technical support, xvi
TRACE and JTAG/SWD connector (P2), 2-26
L
LEDs, 2-20
diagram of locations, 2-20
LED1-4 (GPIO), 2-21
LED5 (reset), 2-21
LED6 (ethernet speed), 2-21
LED7 (power), 2-22
LED8 (SYS_FAULT), 2-22
M
P
package contents, 1-2
power
architecture, 1-15
LED (LED7), 2-22
measurements, 1-15
power connector (P9), 2-27
power-on-self test (POST), 1-14
I-2
U
USB connector (P3), 2-27
V
VREF buffered connector (P10), 2-27
ADSP-CM408F EZ-KIT Lite Evaluation System Manual
Similar pages