PDF User Guides

8-Lead MSOP Evaluation Board User Guide
UG-886
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Universal Evaluation Board for Dual High Speed Op Amps Offered in 8-Lead MSOP
EVALUATION BOARD PHOTOGRAPHS
ANALOG
DEVICES
HSAMP-2RMZ – 8
PWR EVAL BD Z
IN2+
GENERAL DESCRIPTION
C2
C4
R1 6
R1 2
R4
R7
R9
R5
R3
R2
R1
V OUT 2
V OUT 1
13581-001
IN2-
R1 0
R6
R1 3
R11
U1
R8
Figure 1. Evaluation Board, Component Side
0 413 25 A
PWR
VOUT1
VOUT2
13581-002
IN1-
Figure 3 shows the evaluation board schematic. Figure 4 and
Figure 5 show the assembly drawing and the layout pattern of
the component side, respectively. The bill of materials is listed
in Table 1.
RS1
IN2-
The evaluation board is a 6-layer printed circuit board (PCB)
that accepts SMA edge mounted connectors on the inputs and
outputs for efficient connection to test equipment or other
circuitry. The ground plane and component placement minimize
parasitic inductances and capacitances. The evaluation board
components are primarily SMT 0603 case size, with the
exception of the electrolytic bypass capacitors (C1 and C2),
which are 1206 case size.
R1 4
C5
R1 5
C3
RS2
IN1+
The Analog Devices, Inc., dual MSOP universal evaluation
board helps users to evaluate dual, high speed op amps offered
in the 8-lead, mini small outline package (MSOP). The dual
MSOP board is a bare board (that is, there are no components
soldered to the board) that enables users to quickly prototype
a variety of dual op amp circuits, which minimizes risk and
reduces time to market. Figure 1 and Figure 2 show the
component side and solder side, respectively, of the bare
evaluation board.
VP
IN1+
V NC1
IN1-
Enables quick breadboarding/prototyping
User defined circuit configuration
Edge mounted SMA connector provisions
Easy connection to test equipment and other circuits
RoHS compliant
IN2+
FEATURES
Figure 2. Evaluation Board, Solder Side
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 4
UG-886
8-Lead MSOP Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Board Schematics and Artwork ...................................3
General Description ......................................................................... 1
Evaluation Board Assembly Drawing and Layout Pattern ......3
Evaluation Board Photographs ....................................................... 1
Ordering Information .......................................................................4
Revision History ............................................................................... 2
Bill of Materials ..............................................................................4
REVISION HISTORY
10/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 4
8-Lead MSOP Evaluation Board User Guide
UG-886
EVALUATION BOARD SCHEMATICS AND ARTWORK
R5
IN1–
R7
R11
2
1
R9
R3
VOUT1
3
R1
R13
RS1
IN1+
VN GND VP
R15
PIN 4 = VN
PIN 8 = VP
C4
R6
IN2–
R8
R12
C3
C2
C5
6
7
R10
C1
R4
VOUT2
5
R2
R14
RS2
13581-003
IN2+
R16
Figure 3. 8-Lead MSOP Evaluation Board Schematic
13581-004
13581-005
EVALUATION BOARD ASSEMBLY DRAWING AND LAYOUT PATTERN
Figure 5. Component Side Layout Pattern
Figure 4. Component Side Assembly Drawing
Rev. 0 | Page 3 of 4
UG-886
8-Lead MSOP Evaluation Board User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Quantity
3
2
3
1
6
18
Reference Designator
VP, VN, PWR
C1, C2
C3, C4, C5
Device under test
IN1+, IN1−, IN2+, IN2−, VOUT1, VOUT2
R1 to R16, RS1, RS2
Description
Test point
10 µF capacitor
Capacitor, user defined
See data sheet packaging information
SMA/SMT
Resistor, user defined
Package
TP
1206
0603
8-lead MSOP
SMA/SMT
R0603
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG13581-0-10/15(0)
Rev. 0 | Page 4 of 4