AD8222-EVALZ: Precision Instrumentation Amplifier Evaluation Board PDF

Precision Instrumentation Amplifier
Evaluation Board
AD8222-EVALZ
FEATURES
Two AD8222 circuits
Dual channel
Differential out
Easy to connect screw terminals
Decoupled supply lines
Pads for RFI filtering
GENERAL DESCRIPTION
The PCB board has four layers. The top and bottom layers are
used for routing, and the two internal layers are ground planes.
The ground plane was removed underneath the RG resistors.
This is a precaution against any capacitance mismatch at the
two RG pins, which may affect ac CMRR.
JUMPER SETTINGS
Purpose
Connect inputs together
Connect reference pins to
ground
Figure 1. AD8222-EVALZ Evaluation Board Photo
SETTING THE GAIN
The gain setting resistors are R1A and R1B for the dual-channel
part and R11A for the differential output part. The pads are
sized for 0603-sized resistors, although 0402 and 0805 sizes can
also be used.
EMI FILTERING
Table 1.
Jumpers
J1A, J1B, J11
J2A, J2B, J12, J13
06386-001
The AD8222-EVALZ has two AD8222 instrumentation
amplifier circuits: one circuit is configured for dual-channel
operation, while the other is configured for single-channel,
differential output operation. Inputs, outputs, references, and
the supplies are routed to screw terminals for easy connectivity.
Default
Unconnected
Connected
In the default factory setting, the reference pins of the AD8222
are connected to GND through J2A, J2B, J12, and J13.
Therefore, in the shipping configuration, W2A:REF1,
W2B:REF2, W13:REF2, and W13:+IN2 are connected to GND.
To disconnect the terminal from GND, remove the
corresponding jumper.
QUICK START
The quick start feature assumes that the jumpers are in their
factory default positions.
The board comes with 0603 component pads for an EMI filter.
These components are shown in Table 2.
Table 2.
Channel
Dual Channel A
Dual Channel B
Differential Output Channel
Components
R3A, R2A, C1A, C2A, C3A
R3B, R2B, C1B, C2B, C3B
R13, R12, C11, C12, C13
The board, as shipped, does not contain EMI filtering. The
resistors pads are populated with 0 Ω resistors, and the
capacitors are not populated.
See the AD8222 data sheet for more information on EMI
filtering.
To begin:
• Connect ground lead to GND.
• Connect a 15 V supply to +VS.
• Connect a −15 V supply to −Vs.
• Ground −IN1.
• Connect a 1V p-p, 1 kHz source signal to +IN1. A replica of
the signal should now appear at OUT1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD8222-EVALZ
REF1
OUT1
OUT2 REF2
W2A
W2B
REF_A
REF_B
J2A
C4
0.1µF
C1A
SPARE
R3A
0Ω
–IN1
C2A
SPARE
R2A
0Ω
+IN1
–V
15
16
R1A
SPARE
J1A
J2B
+V
14
C1B
SPARE
R2B
0Ω
13
1
12
2
11
3
10
4
9
AD8222
W1A
6
5
7
+V
REF_A
8
+IN2
W1B
C3B
SPARE
DUAL
C3A
SPARE
–IN2
C2B
J1B
SPARE
R3B
0Ω
R1B
SPARE
C5
0.1µF
REF_B
–V
+OUT –OUT
W12
+V
R10
10kΩ
C14
0.1µF
–V
C11
SPARE
R13
0Ω
C12
SPARE
–IN
J11
R12
0Ω
+IN
15
16
14
13
AD8222
1
12
DIFF OUT
11
2
R11A
SPARE
C10
100pF
R11
SPARE
3
W13
10
4
+IN2
9
W11
C13
SPARE
5
6
7
+V
8 C15
0.1µF
REF2
J13
–V
J12
C7
10µF
+V
C8
10µF
–V
W5
+V
06386-002
W6
GND1 GND2 GND3 GND4
–V
Figure 2. AD8222-EVALZ Evaluation Board Schematic
ESD CAUTION
ORDERING GUIDE
Model
AD8222-EVALZ 1
1
Z = Pb-free part.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
EB06386-0-11/06(0)
Rev. 0 | Page 2 of 2
Description
Evaluation Board
Similar pages