Download

All Metals and Long-distance Types
E2V
CSM_E2V_DS_E_3_2
Aluminum and Iron Both
Detectable from Long Distances
2 times the
aluminum detection
distance of
previous models
Twice the max.
distance
Equipped with a
function to prevent
the detection of
aluminum chips
Aluminum chip
protection
Long-distance
aluminum detection
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Refer to Safety Precautions on page 8.
Features
Aluminum Detection Distance: 2 Times Previous Models *
Immunity against aluminum chips has enabled achieving long-distance detection of aluminum workpieces. The same detection distance has also
been achieved for iron, allowing the E2V-X@ to be separated from workpieces made of either metal farther than any other Proximity Sensor.
Aluminum Excellent Performance, with Aluminum Chip Immunity!
Iron Also Detects Iron at Long Distances!
E2V
E2V
E2EZ
E2EZ
Aluminum Chip Immunity
E2EM
E2EM
Long-distance (Ferrous Metals)
E2E
E2E
Standard Model
0
0
1
2
3
4
5
6
7
8
1
9
2
3
4
5
6
7
8 9
Sensing distance (mm)
Sensing distance (mm)
* In-house comparison of M18 Shielded Long-distance Models
Detection Made Visible
An operation indicator that is visible from any direction is provided as a standard feature.
This indicator flashes under unstable conditions for easy installation condition verification at a glance.
The indicator
may be difficult
to see from
some
directions.
Visible
The indicator
is visible
from any
direction.
The indicator
is visible
from any
direction.
180°
180°
180°
Previous Sensor
E2V Pre-wired Models
and Pre-wired Connector Models
E2V Connector Models
Embeddable in Metal.
The first Long-distance Sensor that is shielded. Possible to be completely embedded in metal.
Workpiece
Bracket
Protruding
distance
Workpiece
Embedded Mounting in Metal
E2EM
E2V
1
E2V
Ordering Information
Sensors (Dimensions ➜ page 9)
Standard-distance type
DC 3-wire, Pre-wired Models (Standard Cable Length: 2 m)
Appearance
Sensing distance
M12
Output
PNP
2 mm
NPN
Shielded
M18
PNP
5 mm
NPN
PNP
M30
10 mm
NPN
Model
Operation mode NO
Operation mode NC
E2V-X2B1 2M
E2V-X2C1 2M
E2V-X5B1 2M
E2V-X5C1 2M
E2V-X10B1 2M
E2V-X10C1 2M
E2V-X2B2 2M
E2V-X2C2 2M
E2V-X5B2 2M
E2V-X5C2 2M
E2V-X10B2 2M
E2V-X10C2 2M
Long-distance type
DC 3-wire, Pre-wired Models (Standard Cable Length: 2 m)
Appearance
Sensing distance
M12
Output
PNP
4 mm
NPN
Shielded
PNP
M18
8 mm
NPN
PNP
M30
15 mm
NPN
Model
Operation mode NO
Operation mode NC
E2V-X4B1 2M
E2V-X4C1 2M
E2V-X8B1 2M
E2V-X8C1 2M
E2V-X15B1 2M
E2V-X15C1 2M
E2V-X4B2 2M
E2V-X4C2 2M
E2V-X8B2 2M
E2V-X8C2 2M
E2V-X15B2 2M
E2V-X15C2 2M
Long-distance type
DC 3-wire, Connector Models
Appearance
Sensing distance
M12
Output
PNP
4 mm
NPN
Shielded
M18
PNP
8 mm
M30
NPN
15 mm
PNP
NPN
Model
Operation mode NO
Operation mode NC
E2V-X4B1-M1
E2V-X4C1-M1
E2V-X8B1-M1
E2V-X8C1-M1
E2V-X15B1-M1
E2V-X15C1-M1
E2V-X4B2-M1
E2V-X4C2-M1
E2V-X8B2-M1
E2V-X8C2-M1
E2V-X15B2-M1
E2V-X15C2-M1
Long-distance type
DC 3-wire, Smartclick Pre-wired Connector (M12) Models
Appearance
Sensing distance
M12
PNP
4 mm
NPN
Shielded
M18
M30
Output
PNP
8 mm
NPN
PNP
15 mm
NPN
Model
Operation mode NO
E2V-X4B1-M1TJ 0.3M
E2V-X4C1-M1TJ 0.3M
E2V-X8B1-M1TJ 0.3M
E2V-X8C1-M1TJ 0.3M
E2V-X15B1-M1TJ 0.3M
E2V-X15C1-M1TJ 0.3M
2
E2V
Accessories (Order Separately)
Sensor I/O Connectors (M12, Sockets on One Cable End)
(Required for models with Pre-wired Connectors.) A Connector
is not provided with the Sensor. Be sure to order a Connector separately.
(Dimensions ➜ XS5)
Appearance
Smartclick
Connector,
Straight
Type
Cable length
Model
2m
XS5F-D421-D80-F
5m
XS5F-D421-G80-F
2m
XS5F-D421-D80-P
5m
XS5F-D421-G80-P
Applicable Proximity Sensor Models
Standard cable
Oil-resistant polyurethane
cable
[email protected]
[email protected]
Sensor I/O Connectors (M12, Sockets on One Cable End) Standard type (Required for models for Connectors.) A Connector is not
provided with the Sensor. Be sure to order a Connector separately.
(Dimensions ➜ XS2)
Appearance
Straight
L-shape
Cable length
Sensor I/O Connector
model number
2m
XS2F-D421-DC0-F
5m
XS2F-D421-GC0-F
2m
XS2F-D421-D80-F
5m
XS2F-D421-G80-F
2m
XS2F-D422-DC0-F
5m
XS2F-D422-GC0-F
2m
XS2F-D422-D80-F
5m
XS2F-D422-G80-F
Applicable Proximity Sensor Models
[email protected]
[email protected]
[email protected]@-M1
[email protected]@-M1
[email protected]
[email protected]
[email protected]@-M1
[email protected]@-M1
3
E2V
Ratings and Specifications
Size
M12
Item
Model E2V-X2@@
M18
M30
E2V-X4@@
E2V-X5@@
E2V-X8@@
E2V-X10@@
E2V-X15@@
2 mm±10%
4 mm±10%
5 mm±10%
8 mm±10%
10 mm±10%
15 mm±10%
Set distance
0 to 1.6 mm
0 to 3.2 mm
0 to 4.0 mm
0 to 6.4 mm
0 to 8.0 mm
0 to 12.0 mm
Differential travel
10% max. of sensing distance
Detectable object
Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to
Engineering Data (Reference value).)
Standard sensing
object
Aluminum:
12 × 12 × 3 mm
Aluminum:
12 × 12 × 3 mm
Aluminum:
18 × 18 × 3 mm
Aluminum:
24 × 24 × 3 mm
Aluminum:
30 × 30 × 3 mm
Aluminum:
45 × 45 × 3 mm
Response
frequency *
150 Hz
40 Hz
70 Hz
40 Hz
70 Hz
30 Hz
Power supply
voltage
(operating voltage
range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Current
consumption
450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V)
Control
output
Sensing distance
Load
current
Open-collector output, 100 mA max.
Residual
voltage
2 V max. (Load current: 100 mA, Cable length: 2 m)
NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow)
(lit)
Operation mode
B1/C1 Models: NO
(Refer to the timing charts under I/O Circuit Diagrams for details.)
B2/C2 Models: NC
Protection circuits
Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge
suppressor
Ambient
temperature
Operating/Storage: -25 to 70°C (with no icing or condensation)
Ambient humidity
Operating/Storage: 35% to 95% (with no condensation)
Temperature
influence
Based on the sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence
±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation
resistance
50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength
1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration
resistance
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of
protection
IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.)
Connection
method
Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length:
300 mm)
Materials
Weight
(packed
state)
Indicators
±10% max.
±15% max.
±10% max.
±15% max.
±10% max.
Cable
Approx. 120 g
Approx. 150 g
Approx. 200 g
Connector
Approx. 30 g
Approx. 45 g
Approx. 120 g
Pre-wired
Connector
Models
Approx. 50 g
Approx. 70 g
Approx. 140 g
Case
Nickel-plated brass
Sensing
surface
Heat-resistant ABS
Clamping
nuts
Nickel-plated brass
Toothed
washer
Zinc-plated iron
Accessories
±15% max.
Instruction manual
* The response frequency is an average value.
Measurement conditions are as follows: Standard sensing object, a distance between target objects of twice the size of the standard sensing object, and a set distance
of half the sensing distance.
4
E2V
Engineering Data (Reference Value)
Influence of Sensing Object Size and Material
E2V-X2
E2V-X4
E2V-X5
5.0
3.0
Iron
6.0
Sensing distance X (mm)
4.0
Brass
2.0
Aluminum
Copper
1.5
Stainless steel (SUS304)
1.0
@ d t= 3 mm
0.5
Brass
Sensing distance X (mm)
2.5
Sensing distance X (mm)
7.0
Iron
4.5
3.5
Aluminum
3.0
Copper
2.5
Stainless steel (SUS304)
2.0
1.5
0.0
0
5
10
15
20
25
Side length of sensing object d (mm)
30
E2V-X8
0
5
10
15
20
25
Side length of sensing object d (mm)
6.0
Iron
4.0
Stainless steel (SUS304)
Copper
6.0
Stainless steel (SUS304)
Iron
4.0
@ d t= 3 mm
2.0
X
5
10
15
20
25
30
35
Side length of sensing object d (mm)
40
Brass
Aluminum
14.0
8.0
@ d t= 3 mm
2.0
0
16.0
Aluminum
Sensing distance X (mm)
Sensing distance X (mm)
Sensing distance X (mm)
Aluminum
X
18.0
10.0
Copper
Stainless steel (SUS304)
2.0
E2V-X15
Brass
Brass
Iron
3.0
0.0
30
12.0
8.0
Aluminum
1.0
E2V-X10
10.0
Copper
4.0
@ d t= 3 mm
X
0.5
0.0
5.0
t= 3 mm
@d
1.0
X
Brass
Copper
12.0
Iron
10.0
8.0
Stainless steel (SUS304)
6.0
4.0
@ d t= 3 mm
X
X
2.0
0.0
0
5
10
15
20
25
30
35
Side length of sensing object d (mm)
0.0
40
0
10
20
30
40
50
Side length of sensing object d (mm)
0.0
60
0
10
20
30
40
50
Side length of sensing object d (mm)
60
Influence of Sensing Object Size and Material
E2V-X2
E2V-X4
3.0
E2V-X5
5.0
7.0
4.5
Brass
Iron
Aluminum
Copper
1.5
1.0
Stainless steel
(SUS304)
0.5
t
0
1
2
3
4
5
Thickness of sensing object: t (mm)
Aluminum
3.0
Copper
2.5
2.0
Stainless steel (SUS304)
1.5
1.0
t
X
0.5
Sensing object size: 12 × 12 mm
0.0
3.5
6
Sensing distance X (mm)
Brass
2.0
6.0
Iron
4.0
Sensing distance X (mm)
Sensing distance X (mm)
2.5
0.0
X
Aluminum
5.0
Iron
4.0
Copper
3.0
Stainless steel (SUS304)
2.0
t
1.0
1
2
3
4
5
Thickness of sensing object: t (mm)
X
Sensing object size: 18 × 18 mm
Sensing object size: 12 × 12 mm
0
Brass
6
0.0
0
1
2
3
4
5
6
7
Thickness of sensing object: t (mm)
8
5
E2V
E2V-X8
E2V-X10
10.0
18.0
12.0
16.0
Aluminum
Brass
Brass
10.0
8.0
6.0
Stainless steel (SUS304)
4.0
2.0
t
Iron
8.0
Copper
6.0
Stainless steel (SUS304)
4.0
Sensing object size: 24 × 24 mm
0.0
0
1
2
3
4
5
6
7
Thickness of sensing object: t (mm)
Iron
12.0
Copper
10.0
Stainless steel (SUS304)
8.0
6.0
t
X
Sensing object size: 30 × 30 mm
0.0
8
Brass
4.0
t
2.0
X
Sensing distance X (mm)
Copper
Iron
Aluminum
14.0
Aluminum
Sensing distance X (mm)
Sensing distance X (mm)
E2V-X15
Sensing object size: 45 × 45 mm
0.0
0
2
4
6
8
10
Thickness of sensing object: t (mm)
X
2.0
12
0
2
4
6
8
10
Thickness of sensing object: t (mm)
12
Sensing Area
16.0
14.0
16.0
Y
X
14.0
Y
X
E2V-X15@
E2V-X15@
12.0
[email protected]
E2V-X8@
8.0
6.0
E2V-X5@
4.0
E2V-X4@
2.0
E2V-X2@
Sensing distance X (mm)
Sensing distance X (mm)
12.0
10.0
E2V-X10@
8.0
E2V-X8@
6.0
E2V-X5@
4.0
E2V-X4@
2.0
E2V-X2@
0.0
-12.0
-9.0
-6.0 -3.0 0.0 3.0 6.0
9.0 12.0
Sensing distance Y (mm)
Sensing area (Aluminum) (Thickness: 3.0 mm)
0.0
-12.0
-9.0
-6.0 -3.0 0.0
3.0
6.0 9.0 12.0
Sensing distance Y (mm)
Sensing area (Iron) (Thickness: 3.0 mm)
6
E2V
I/O Circuit Diagrams
NPN Output
Model
Operation mode
Timing charts
Output circuit
Set position
Non-sensing Unstable
Stable sensing
area
sensing area area
Proximity sensor
Brown
Sensing object
NO
+V
100 80
(%)
Load
0
Rated
sensing
distance
Flashing
Proximity
Sensor
main
circuit
ON
Yellow indicator
OFF
ON
Control output
OFF
[email protected]@
(-M1/-M1TJ)
Black
Blue
0V
Non-sensing area
Sensing area
Note: Connector Models
NO Models:
NC Models:
Proximity sensor
Sensing object
100
(%)
NC
0
M1:
M1TJ:
Rated sensing
distance
ON Yellow indicator
OFF
ON Control output
OFF
Compatible Connector Cables: XS5F Series
XS2F Series
PNP Output
Model
Operation mode
Timing charts
Output circuit
Set position
Non-sensing Unstable
Stable sensing
area
sensing area area
Proximity sensor
Brown
Sensing object
NO
(%)
+V
100 80
Rated
sensing
distance
Flashing
0
Proximity
Sensor
main
circuit
ON
Yellow indicator
OFF
ON
Control output
OFF
[email protected]@
(-M1/-M1TJ)
Black
Load
Blue
0V
Sensing area
Proximity sensor
Non-sensing area
Note: Connector Models
NO Models:
NC Models:
Sensing object
(%)
NC
100
0
M1:
M1TJ:
Rated sensing
distance
ON Yellow indicator
OFF
ON Control output
OFF
Compatible Connector Cables: XS5F Series
XS2F Series
Connections for Sensor I/O Connectors
Sensor I/O Connector
model number
XS2F-D42@[email protected]
NO
[email protected]
[email protected]
D: 2-m cable
G: 5-m cable
E2V
Main
Circuit
1: Straight
2: L-shape
Connections
XS2F
1
1
2
2
3
3
4
4
E2V
DC 3-wire
1: Straight
2: L-shape
Main
Circuit
Model
Brown (+V)
Blue (0 V)
Black (Output)
XS2F
1
1
2
2
3
3
4
4
Brown (+V)
White (Blank)
Blue (0 V)
Black (Output)
XS2F-D42@[email protected]
NC
[email protected]
[email protected]
D: 2-m cable
G: 5-m cable
E2V
Main
Circuit
Type
Proximity Sensor
Operation
mode
XS2F
1
1
2
2
3
3
4
4
Brown (+V)
White (Output)
Blue (0 V)
Black (Blank)
Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details.
7
E2V
Safety Precautions
Refer to the Proximity Sensors Technical Guide.
WARNING
Sensing Distance
This product is not designed or rated for ensuring
safety of persons. Do not use it for such purposes.
• The sensing distance depends on the sensing object size,
material, and thickness.
• If the sensing object has a thickness of less than 1 mm, the sensing
distance will decrease.
• In some cases, it may not be possible to detect stainless steel.
Use the following graph and the Influence of Sensing Object Size
and Material information in Engineering Data (Reference Value) as
a reference.
Never use the product with an AC power supply.
Otherwise, explosion may result.
Precautions for Correct Use
Do not use the product in atmospheres or environments that exceed
product ratings.
Designing
Influence of Surrounding Metal
When embedding the Sensor in metal, be sure that the clearances given
in the following table are maintained.
D
m
t
t
t
Table 1. Influence of Surrounding Metal
Item
Model
ℓ
d dia.
D
m
n
Normally aluminum or iron cuttings will not be detected even if they
adhere to or accumulate on the sensing surface. Detection signals
may be output for the following. If this occurs, remove the cuttings
from the sensing surface.
Diameter of cutting = d and diameter of sensing surface = D
Cuttings in center of sensing surface
with d ≥ 2/3D
(Unit: mm)
Mode
Size
D
E2V-X2@/X4@
10
E2V-X5@/X8@
16
E2V-X10@/X15@
28
n
m
d dia.
Aluminum and Iron Cuttings
E2V-X2
0
12
0
12
18
E2V-X5
0
18
0
24
27
(Unit: mm)
E2V-X10
0
30
0
45
45
E2V-X4
0
12
0
12
18
E2V-X8
0
18
0
24
27
E2V-X15
0*
30 *
0*
45
45
d
Pressed against
Cutting sensing surface.
Cutting
Sensing
surface
D
Tightening Torque
Do not tighten the nut with excessive force.
A washer must be used with the nut.
(Shielded Model)
Part B Part A
Item
Model
ℓ
d dia.
D
m
n
Tightening Torque
Model
E2V-X2/X4
E2V-X5/X8
E2V-X10/X15
Part A
Dimension (mm)
17
22
26
Torque
5.9 N⋅m
15 N⋅m
39 N⋅m
Part B
Torque
9.8 N⋅m
45 N⋅m
78 N⋅m
* If the thickness of the mounting bracket (t) exceeds 5 mm, be sure to install
the Sensor so that ℓ ≥ 2, d (dia.) ≥ 45, and D ≥ 2.
Mutual Interference
When installing Sensors face-to-face or side-by-side, be sure that the
minimum distances given in table 2 are maintained.
B
A
Chart 2. Mutual Interference
Item
Model
E2V-X2
30
20
E2V-X5
50
30
(Unit: mm)
E2V-X10
100
50
Model
E2V-X4
35
25
E2V-X8
60
35
E2V-X15
120
70
A
B
Item
A
B
8
E2V
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
Sensors
Pre-wired Models
E2V-X5/X8
E2V-X2/X4
21 dia.
6-dia. vinyl-insulated round cable
with 3 conductors
(Conductor cross section: 0.5 mm2,
Insulator diameter: 1.9 mm),
Standard length: 2 m
60
17
47
M12 × 1
60
52
29 dia.
42
24
Indicator *1
Two clamping nuts
Toothed washer
4
6-dia. vinyl-insulated round cable
with 3 conductors
(Conductor cross section: 0.5 mm2,
Insulator diameter: 1.9 mm),
Standard length: 2 m
Indicator *1
M18 × 1
4
Two clamping nuts
Toothed washer
E2V-X10/X15
60
52
42 dia.
6-dia. vinyl-insulated round cable
with 3 conductors
(Conductor cross section: 0.5 mm2,
Insulator diameter: 1.9 mm),
Standard length: 2 m
42
36
Indicator *1
M30 × 1.5
5
Two clamping nuts
Toothed washer
*1 NO Models: Operation indicator (yellow) (flashing)
Setting indicator (yellow) (ON)
NC Models: Operation indicator (yellow) (ON)
Pre-wired Connector Models
E2V-X4-M1TJ
E2V-X8-M1TJ
21 dia.
17
47
M12 × 1
4
60
29 dia.
60
6-dia. vinyl-insulated round cable
Standard length: 300 mm
Indicator *1
Two clamping nuts
Toothed washer
52
42
24
M12 × 1
6-dia. vinyl-insulated round cable
Standard length: 300 mm
Indicator *1
M18 × 1
4
M12 × 1
Two clamping nuts
Toothed washer
E2V-X15-M1TJ
60
52
42
42 dia.
36
6-dia. vinyl-insulated round cable
Standard length: 300 mm
Indicator *1
M30 × 1.5
5
M12 × 1
Two clamping nuts
Toothed washer
*1 NO Models: Operation indicator (yellow) (flashing)
Setting indicator (yellow) (ON)
NC Models: Operation indicator (yellow) (ON)
9
E2V
Connector Models
B
Model
D
C
E
F
A
G
Item
M12 × 1
Four indicators *1
Two clamping nuts
Toothed washer
*1 NO Models: Operation indicator (yellow) (flashing)
Setting indicator (yellow) (ON)
NC Models: Operation indicator (yellow) (ON)
A
B
C
D
E
F
G
E2V-X4@-M1
E2V-X8@-M1
E2V-X15@-M1
M12 × 1
65
47
52
21 dia.
17
4
M18 × 1
60
42
47
29 dia.
24
4
M30 × 1.5
63
42
49
42 dia.
36
5
Mounting Hole Dimensions
Proximity Sensor dimensions
Dimension H (mm)
M12
12.5
+0.5
0
M18
dia.
18.5
+0.5
0
M30
dia.
30.5
+0.5
0
dia.
H
10
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.4
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.
Similar pages