REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Page 2, 1.4, add IVR test conditions. Page 4, table I, IIB and IOS, add footnote 88-07-19 M. A. FRYE to guarantee subgroup 3. For IOS, change unit from pA to nA. For VO, add subgroup 6. Editorial changes throughout. B Add device type 02 and case outline, F-4. Editorial changes throughout. 91-03-07 M. A. FRYE C Change boilerplate to add one-part part numbers. Add delta test limits. 96-11-13 R. MONNIN D Make changes to table IIA. - ro 02-01-07 R. MONNIN E Make change to the first condition of the AVO test in table I from RL = 1 kΩ to RL = 10 kΩ. -rrp 02-07-23 R. MONNIN F Drawing updated to reflect current requirements. -rrp 09-03-09 R. HEBER G Update drawing to current MIL-PRF-38535 requirements. –rrp 15-01-26 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY MARCIA B. KELLEHER STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil CHECKED BY D. A. DiCENZO APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A ROBERT P. EVANS DRAWING APPROVAL DATE 87-11-27 REVISION LEVEL G MICROCIRCUIT, LINEAR, HIGH SPEED, FAST SETTLING, PRECISION OPERATIONAL AMPLIFIER, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-88513 1 OF 11 5962-E121-15 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device class M and Q: 5962 - Federal stock class designator \ RHA designator (see 1.2.1) 88513 01 G A Device type (see 1.2.2) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number For device class V: 5962 - Federal stock class designator \ RHA designator (see 1.2.1) 88513 01 V G A Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 OP-42A 02 OP-42B Circuit function High speed, fast settling, precision operational amplifier High speed, fast settling, precision operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class M Q or V Device requirements documentation Vendor self-certification to the requirements for MIL-STD-883 compliant, nonJAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Certification and qualification to MIL-PRF-38535 STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter G H P 2 Descriptive designator MACY1-X8 GDFP1-F10 or CDFP2-F10 GDIP1-T8 or CDIP2-T8 CQCC1-N20 Terminals Package style 8 10 8 20 Can Flat pack Dual-in-line Square lead less chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) ....................................................................... ±20 V Input voltage (VIN) ......................................................................... Differential input voltage ................................................................ Output short-circuit duration .......................................................... Storage temperature range ........................................................... Lead temperature (soldering, 60 seconds)..................................... Power dissipation (PD) ................................................................... ±20 V 2/ ±40 V 2/ Indefinite -65°C to +150°C +300°C 500 mW 3/ Thermal resistance, junction-to-case (θJC) .................................... See MIL-STD-1835 Thermal resistance, junction-to-ambient (θJA): Case G ....................................................................................... 150°C/W Cases H and P ........................................................................... 119°C/W Case 2 ........................................................................................ 120°C/W 1.4 Recommended operating conditions. Supply voltage (VS)........................................................................ ±15 V Source resistance (RS) .................................................................. 50 Ω Common mode voltage (VCM) ....................................................... 0 V Input voltage range (VINR) ............................................................. ±11 V Ambient operating temperature range (TA) .................................... -55°C to +125°C _____ 1/ Unless otherwise specified, TA = +25°C. 2/ For supply voltages less than 20 V, the absolute maximum input voltage is equal to the supply voltage. 3/ Must withstand the added PD due to short circuit test, e.g., ISC. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein . 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. TABLE I. Electrical performance characteristics. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 4 Test Symbol Conditions 1/ -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type Limits 1 01 Max ±1.0 02 ±1.5 2,3 All ±2.0 1 All ±200 pA ±20 nA ±40 pA ±1 nA Min Input offset voltage VOS Input bias current IIB 2,3 2/ Input offset current 1 IOS All 2,3 2/ Common mode rejection 3/ CMR 1 VCM = IVR = ±11 V All 86 2,3 Power supply rejection ratio PSRR 1 VS = ±10 V to ±20 V ISC Output shorted to ground 1 All All External VOS trim range 20 60 8 60 All 1 All ±2.5 RL = 1 kΩ 4 All ±11.5 RL = 2 kΩ 5,6 VO = 0 V, no load VOS RPOT = 10 kΩ, µV/V 50 1,2,3 ISY dB 40 2,3 Supply current mV 80 2,3 Short circuit output current Unit mA 6.0 mA ±10 mV TA = +25°C Output voltage swing Large signal voltage gain VO AVO 4 RL = 10 kΩ, VO = ±10 V RL = 2 kΩ, VO = ±10 V RL = 1 kΩ, VO = ±10 V, V ±11.0 All 500 5,6 160 4 200 5,6 80 4 100 V/mV TA = +25°C See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 5 TABLE I. Electrical performance characteristics – Continued. Test Slew rate 4/ Symbol SR Conditions 1/ -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type 7 All AVCL = +1, RL = 2 kΩ Limits Min 45 8 Unit Max V/µs 40 Input offset voltage temperature coefficient TCVOS TA = -55°C, +125°C 8 All 10 µV/°C Settling time tS See figure 2, TA = +25°C, 9 All 1.0 µs 0.1 % for 10 V step 1/ Unless otherwise specified, VS = ±15 V, VCM = 0 V, RS = 50 Ω, and TA = TJ. 2/ Subgroup 3, if not tested, shall be guaranteed to the limits specified in table I herein. 3/ IVR is defined as the VCM range used for the CMR test. 4/ Slew rate may be specified separately for positive and negative going changes. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MILPRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 6 Device types 01 Case outlines G and P 02 2 H Terminal number 1 Terminal symbol NULL NC NC 2 -INPUT NULL NULL 3 +INPUT NC -INPUT 4 -V NC +INPUT 5 NULL -INPUT -V 6 OUTPUT NC NULL 7 +V +INPUT OUTPUT 8 NC NC +V 9 --- NC NC 10 --- -V NC 11 --- NC --- 12 --- NULL --- 13 --- NC --- 14 --- NC --- 15 --- OUTPUT --- 16 --- NC --- 17 --- +V --- 18 --- NC --- 19 --- NC --- 20 --- NC --- NC = No connection FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 7 NOTES: Schottky diodes D1 – D4 are HP5082-2835 or equivalent. IC1 is CLC200A1 or equivalent. IC2 is OP41EJ or equivalent. FIGURE 2. Settling-time test circuit. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 8 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015. (2) TA = +125°C, minimum. b. Interim and final electrical test parameters shall be as specified in table IIA herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table IIA herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. a. Tests shall be as specified in table IIA herein. b. Subgroups 10 and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 9 TABLE IIA. Electrical test requirements. Test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Device class M 1 1 1 1,2,3,4,5, 1/ 6,7,8 1,2,3,4,5, 1/ 6,7,8 1,2,3,4,5, 2/ 3/ 6,7,8 Group A test requirements (see 4.4) 1,2,3,4,5, 6,7,8,9 1,2,3,4,5, 6,7,8,9 1,2,3,4,5, 6,7,8,9 Group C end-point electrical parameters (see 4.4) Group D end-point electrical parameters (see 4.4) Group E end-point electrical parameters (see 4.4) 1 1 1 3/ 1 1 1 Interim electrical parameters (see 4.2) Final electrical parameters (see 4.2) Subgroups (in accordance with MIL-PRF-38535, table III) Device class Q --- Device class V --- --- 1/ PDA applies to subgroup 1. 2/ PDA applies to subgroups 1 and 7. Exclude deltas from PDA. 3/ See table IIB for delta measurement parameters. TABLE IIB. 240 hour burn-in and group C end-point electrical parameters. Test Limit Min VOS IIB -200 Unit Max +1 +200 Delta Unit mV Min -500 Max +500 µV pA -100 +100 pA 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. b. TA = +125°C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 10 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table IIA herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25°C ±5°C, after exposure, to the subgroups specified in table IIA herein. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in MIL-HDBK-103 and QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DLA Land and Maritime-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime-VA. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88513 A REVISION LEVEL G SHEET 11 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 15-01-26 Approved sources of supply for SMD 5962-88513 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ Reference military specification PIN 5962-8851301GA 24355 (2) OP-42AJ/883 M38510/12208BGA 5962-8851301PA 24355 (2) OP-42AZ/883 M38510/12208BPA 5962-88513012A 24355 (2) OP-42ARC/883 M38510/12208B2A 5962-8851301VGA 24355 (4) OP-42AJ/QMLV --- 5962-8851301VPA 24355 (4) OP-42AZ/QMLV --- 5962-8851301V2A 3/ OP-42ARC/QMLV --- 5962-8851302HA 24355 (2) OP-42BL/883 --- 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number Vendor name and address 24355 Analog Devices (2) RT 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: 804 Woburn Street Wilmington, MA 01887-3462 24355 Analog Devices (4) RT 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: 7910 Triad Center Drive Greensboro, NC 27409-9605 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.