Low Noise, Precision, 16 V, CMOS, Rail-to-Rail Operational Amplifiers AD8663/AD8667/AD8669 Data Sheet FEATURES PIN CONFIGURATIONS TOP VIEW (Not to Scale) NC NC 1 8 NC 7 V+ –IN 2 7 V+ +IN 3 6 OUT TOP VIEW +IN 3 (Not to Scale) 6 OUT 5 NC V– 4 NC = NO CONNECT –IN A 2 +IN A 3 V– 4 8 AD8667 TOP VIEW (Not to Scale) 7 NOTES 1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 2. CONNECT THE EXPOSED PAD TO V– OR LEAVE IT UNCONNECTED. Figure 2. 8-Lead LFCSP (CP-8-13) V+ OUT B 6 –IN B 5 +IN B Figure 3. 8-Lead MSOP (RM-8), 8-Lead SOIC (R-8) 5 NC V– 4 Figure 1. 8-Lead SOIC (R-8) OUT A 1 Sensor front ends Transimpedance amplifiers Electrometer applications Photodiode amplification Low power ADC drivers Medical diagnostic instruments pH and ORP meters and probes DAC or REF buffers 8 06742-002 AD8663 06742-001 NC 1 –IN 2 OUT A 1 14 OUT D –IN A 2 13 –IN D +IN A 3 12 +IN D V+ 4 AD8648 AD8669 +IN B TOP VIEW 11 V– (Not to Scale) 5 10 +IN C –IN B 6 9 –IN C OUT B 7 8 OUT C 06742-004 APPLICATIONS AD8663 06742-003 Low offset voltage: 175 μV maximum @ VSY = 5 V Low supply current: 275 μA maximum per amplifier Single-supply operation: 5 V to 16 V Low noise: 23 nV/√Hz Low input bias current: 300 fA Unity-gain stable Small packages available 3 mm × 3 mm, 8-lead LFCSP 8-lead MSOP Other packages 8-lead SOIC 14-lead SOIC 14-lead TSSOP Figure 4. 14-Lead SOIC (R-14), 14-Lead TSSOP (RU-14) GENERAL DESCRIPTION The AD8663/AD8667/AD8669 are rail-to-rail output amplifiers that use the Analog Devices, Inc., patented DigiTrim® trimming technique to achieve low offset voltage. The AD8663/AD8667/ AD8669 feature an extended operating range with supply voltages up to 16 V. They also feature low input bias current, low input offset voltage, and low current noise. The combination of low offset, very low input bias current, and a wide supply range makes these amplifiers useful in a wide variety of applications usually associated with higher priced JFET amplifiers. Systems using high impedance sensors, such as photodiodes, benefit from the combination of low input bias current, low noise, low offset, and wide bandwidth. The ability to operate the device for single (5 V to 16 V) or dual supplies (±2.5 V to ±8 V) supports many applications. The railto-rail outputs provide increased dynamic range to drive low Rev. D frequency data converters. The low bias current drift is wellsuited for precision I-to-V converters. The combination of precision offset, offset drift, and low noise also make the op amps ideal for gain, dc offset adjust, and active filter in both instrumentation and medical applications. These low power op amps can be used in IR thermometers, pH and ORP instruments, pressure transducer front ends, and other sensor signal conditioning circuits that are used in remote or wireless applications. The AD8663/AD8667/AD8669 are specified over the extended industrial temperature range of −40°C to +125°C. The single AD8663 is available in a narrow 8-lead SOIC package and a very thin, 8-lead LFCSP. The dual AD8667 is available in a narrow 8-lead SOIC package and an 8-lead MSOP. The quad AD8669 is available in a 14-lead SOIC and 14-lead small TSSOP. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2007–2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD8663/AD8667/AD8669 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Absolute Maximum Ratings ............................................................5 Applications ....................................................................................... 1 Thermal Resistance .......................................................................5 Pin Configurations ........................................................................... 1 ESD Caution...................................................................................5 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6 Revision History ............................................................................... 2 Outline Dimensions ....................................................................... 13 Specifications..................................................................................... 3 Ordering Guide .......................................................................... 15 Electrical Characteristics ............................................................. 3 REVISION HISTORY 5/2016—Rev. C to Rev. D Changed CP-8-2 to CP-8-13 ........................................ Throughout Changes to Figure 2 .......................................................................... 1 Changes to Table 4 ............................................................................ 5 Updated Outline Dimensions ....................................................... 13 Changes to Ordering Guide .......................................................... 15 4/2013—Rev. B to Rev. C Changes to Figure 2 .......................................................................... 1 Added Exposed Pad Notation to Outline Dimensions ............. 14 Changes to Ordering Guide .......................................................... 15 1/2008—Rev. A to Rev. B Added TSSOP ..................................................................... Universal Change to Table 4 ............................................................................. 5 Changes to Figure 8 and Figure 9 ................................................... 6 Changes to Figure 23 and Figure 26............................................... 9 Updated Outline Dimensions ....................................................... 13 Changes to Ordering Guide .......................................................... 15 10/2007—Rev. 0 to Rev. A Added AD8667 and AD8669 ............................................ Universal Changes to Features ..........................................................................1 Changes to General Description .....................................................1 Inserted Figure 3 and Figure 4 .........................................................1 Changes to Table 1, Power Supply Section .....................................3 Changes to Table 2.............................................................................4 Reformatted Typical Performance Characteristics Section .........6 Changes to Figure 5 ...........................................................................6 Changes to Figure 13.........................................................................7 Changes to Figure 17 and Figure 20 ...............................................8 Inserted Figure 35 through Figure 39 .......................................... 11 Inserted Figure 40 and Figure 41.................................................. 12 Updated Outline Dimensions ....................................................... 13 Changes to Ordering Guide .......................................................... 15 7/2007—Revision 0: Initial Version Rev. D | Page 2 of 15 Data Sheet AD8663/AD8667/AD8669 SPECIFICATIONS ELECTRICAL CHARACTERISTICS VSY = 5.0 V, VCM = VSY/2, TA = 25°C, unless otherwise noted. Table 1. Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol Conditions VOS VCM = VSY/2 −40°C < TA < +125°C Min IB Typ Max Unit 30 175 450 µV µV pA pA pA pA pA pA V dB dB dB dB µV/°C 0.3 −40°C < TA < +85°C −40°C < TA < +125°C Input Offset Current 45 105 IOS 0.2 −40°C < TA < +85°C −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio CMRR Large Signal Voltage Gain AVO Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High TCVOS VOH Output Voltage High VOH Output Voltage Low VOL Output Voltage Low VOL Short-Circuit Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current per Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Peak-to-Peak Noise Voltage Noise Density Current Noise Density ISC ZOUT PSRR ISY VCM = 0.2 V to 3.0 V −40°C < TA < +125°C RL = 100 kΩ, VOUT = 0.5 V to 4.5 V RL = 2 kΩ, VOUT = 0.5 V to 4.5 V −40°C < TA < +125°C IL = 100 µA −40°C < TA < +125°C IL = 1 mA −40°C < TA < +125°C IL = 100 µA −40°C < TA < +125°C IL = 1 mA −40°C < TA < +125°C 0.2 76 76 115 106 4.95 4.90 4.65 4.60 100 100 140 114 1.5 5 4.97 4.80 17 150 25 35 200 250 ±7 120 f = 100 kHz, AV = 1 VSY = 5 V to 16 V −40°C < TA < +125°C VOUT = VSY/2 −40°C < TA < +125°C 35 65 3.0 95 95 105 210 275 325 V V V V mV mV mV mV mA Ω dB dB μA μA SR GBP ΦM RL = 2 kΩ CL = 20 pF CL = 20 pF 0.26 520 60 V/µs kHz Degrees en p-p en f = 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 1 kHz 2.5 23 21 0.05 µV p-p nV/√Hz nV/√Hz pA/√Hz in Rev. D | Page 3 of 15 AD8663/AD8667/AD8669 Data Sheet VSY = 16.0 V, VCM = VSY/2, TA = 25°C, unless otherwise noted. Table 2. Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol Conditions VOS VCM = VSY/2 −40°C < TA < +125°C Min IB Typ Max Unit 40 300 500 µV µV pA pA pA pA pA pA V dB dB dB dB µV/°C 0.3 −40°C < TA < +85°C −40°C < TA < +125°C Input Offset Current 45 120 IOS 0.2 −40°C < TA < +85°C −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio CMRR Large Signal Voltage Gain AVO Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High TCVOS VOH Output Voltage High VOH Output Voltage Low VOL Output Voltage Low VOL Short-Circuit Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current per Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Peak-to-Peak Noise Voltage Noise Density Current Noise Density ISC ZOUT PSRR ISY VCM = 0.2 V to 14.5 V −40°C < TA < +125°C RL = 100 kΩ, VOUT = 0.5 V to 15.5 V RL = 2 kΩ, VOUT = 0.5 V to 15.5 V −40°C < TA < +125°C IL = 100 μA −40°C < TA < +125°C IL = 1 mA −40°C < TA < +125°C IL = 100 μA −40°C < TA < +125°C IL = 1 mA −40°C < TA < +125°C 0.2 87 87 115 106 15.95 15.90 15.85 15.80 109 109 140 111 1.5 5 15.98 15.92 17 70 25 35 100 125 ±50 100 f = 100 kHz, AV = 1 VSY = 5 V to 16 V −40°C < TA < +125°C VOUT = VSY/2 −40°C < TA < +125°C 35 65 14.5 95 95 105 230 285 355 V V V V mV mV mV mV mA Ω dB dB μA μA SR GBP ΦM RL = 2 kΩ CL = 20 pF CL = 20 pF 0.3 540 64 V/µs kHz Degrees en p-p en f = 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 1 kHz 2.5 23 21 0.05 µV p-p nV/√Hz nV/√Hz pA/√Hz in Rev. D | Page 4 of 15 Data Sheet AD8663/AD8667/AD8669 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 3. Parameter Supply Voltage Input Voltage Differential Input Voltage Output Short-Circuit Duration to GND Storage Temperature Range Operating Temperature Range Junction Temperature Range Lead Temperature, Soldering (60 sec) θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Rating 18 V −0.1 V to VSY 18 V Indefinite −60°C to +150°C −40°C to +125°C −65°C to +150°C 300°C Table 4. Thermal Resistance Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Package Type 8-Lead SOIC (R-8) 8-Lead LFCSP (CP-8-13) 8-Lead MSOP (RM-8) 14-Lead SOIC (R-14) 14-Lead TSSOP (RU-14) 1 θJA 121 751 145 90 180 Exposed pad soldered to application board. ESD CAUTION Rev. D | Page 5 of 15 θJC 43 18 1 45 45 35 Unit °C/W °C/W °C/W °C/W °C/W AD8663/AD8667/AD8669 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 10000 1600 VSY = 5V –0.1V < VCM < +3.5V TA = 25°C VSY = 16V –0.1V < VCM < +14V TA = 25°C 9000 8000 1200 NUMBER OF AMPLIFIERS NUMBER OF AMPLIFIERS 1400 1000 800 600 400 7000 6000 5000 4000 3000 2000 200 –50 0 50 VOS (µV) 100 150 200 250 0 –250 –200 –150 –100 –50 06742-005 0 –250 –200 –150 –100 40 40 VSY = ±2.5V –40°C < TA < +125°C 150 200 250 VSY = ±8V –40°C < TA < +125°C 35 NUMBER OF AMPLIFIERS 35 100 Figure 8. Input Offset Voltage Distribution Figure 5. Input Offset Voltage Distribution 30 25 20 15 10 30 25 20 15 10 5 5 3 2 TCVOS (µV) 1 0 5 4 0 06742-006 0 0 1 2 3 TCVOS (µV/°C) 4 5 06742-038 NUMBER OF AMPLIFIERS 0 50 VOS (µV) 06742-037 1000 Figure 9. Offset Voltage Drift Distribution Figure 6. Offset Voltage Drift Distribution 300 500 VSY = 5V 400 TA = 25°C VSY = 16V TA = 25°C 250 200 300 150 100 VOS (µV) 100 0 –100 50 0 –50 –100 –200 –150 –300 –200 –400 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VCM (V) 5.0 –300 0 2 4 6 8 10 12 14 VCM (V) Figure 7. Input Offset Voltage vs. Common-Mode Voltage Figure 10. Input Offset Voltage vs. Common-Mode Voltage Rev. D | Page 6 of 15 16 06742-010 –250 –500 06742-007 VOS (µV) 200 Data Sheet AD8663/AD8667/AD8669 100 100 VSY = 5V TA = 125°C VSY = 16V TA = 125°C 80 60 60 40 40 20 20 1.0 1.5 2.0 2.5 3.0 3.5 4.5 4.0 VCM (V) 0 0.5 06742-013 0 0.5 6.5 8.5 10.5 12.5 14.5 Figure 14. Input Bias Current vs. Common-Mode Voltage at 125°C 100 VSY = 5V TA = 25°C 80 70 70 CMRR (dB) 80 60 60 50 50 40 40 30 30 1k 10k 100k 1M 10M FREQUENCY (Hz) 20 100 06742-023 20 100 VSY = 16V TA = 25°C 90 1k Figure 12. CMRR vs. Frequency, VSY = 5 V 10000 VSY = 5V TA = 25°C 1000 100 VSY – VOH SOURCING VOL SINKING 10 0.01 0.1 1 LOAD CURRENT (mA) 10 06742-011 1 0.1 0.001 100k 1M 10M Figure 15. CMRR vs. Frequency, VSY = 16 V OUTPUT SATURATION VOLTAGE (mV) 10000 10k FREQUENCY (Hz) Figure 13. Output Swing Saturation Voltage vs. Load Current VSY = 16V TA = 25°C 1000 100 VSY – VOH SOURCING VOL SINKING 10 1 0.1 0.001 0.01 0.1 1 10 100 LOAD CURRENT (mA) Figure 16. Output Swing Saturation Voltage vs. Load Current Rev. D | Page 7 of 15 06742-014 90 06742-039 100 OUTPUT SATURATION VOLTAGE (mV) 4.5 VCM (V) Figure 11. Input Bias Current vs. Common-Mode Voltage at 125°C CMRR (dB) 2.5 06742-016 IB (pA) IB (pA) 80 AD8663/AD8667/AD8669 Data Sheet 350 140 300 120 200 VOL @ 1mA 150 100 VOL @ 100µA –25 –10 5 20 35 50 65 80 95 VOL @ 1mA 60 40 110 125 TEMPERATURE (°C) GAIN (dB) AND PHASE (Degrees) PHASE 60 CL = 0pF 20 0 –20 –40 CL = 200pF 10k 100k 10M 1M FREQUENCY (Hz) G = 100 80 95 110 125 PHASE 60 40 CL = 0pF GAIN 20 0 –20 –40 CL = 200pF 10k 100k 10M 1M VSY = 16V TA = 25°C G = 100 40 G = 10 G=1 –20 –40 100 65 G = 10 20 G=1 0 –20 1k 10k 100k 1M FREQUENCY (Hz) 10M Figure 19. Closed-Loop Gain vs. Frequency –40 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 22. Closed-Loop Gain vs. Frequency, VSY = 16 V Rev. D | Page 8 of 15 10M 06742-021 0 50 60 VSY = 5V TA = 25°C ACL (dB) 20 35 Figure 21. Open-Loop Gain and Phase Shift vs. Frequency 06742-018 ACL (dB) 40 20 FREQUENCY (Hz) Figure 18. Open-Loop Gain and Phase Shift vs. Frequency 60 5 80 –60 VSY = 16V TA = 25°C –80 100 1k 06742-017 GAIN (dB) AND PHASE (Degrees) 120 100 –60 VSY = 5V TA = 25°C –80 100 1k –10 Figure 20. Output Voltage Saturation vs. Temperature 120 GAIN –25 TEMPERATURE (°C) 100 40 VSY – VOH @ 100µA 0 –40 Figure 17. Output Voltage Saturation vs. Temperature 80 VOL @ 100µA 20 VSY – VOH @ 100µA 0 –40 80 06742-020 50 VSY – VOH @ 1mA 100 06742-045 DROP OUT VOLTAGE (mV) 250 06742-044 DROP OUT VOLTAGE (mV) VSY – VOH @ 1mA Data Sheet AD8663/AD8667/AD8669 1000 1000 G = 100 G = 100 100 100 G = 10 10 10 1 100k 1M 10M FREQUENCY (Hz) Figure 23. Closed-Loop Output Impedance vs. Frequency, VSY = 5 V 90 50 PSRR (dB) 60 50 40 PSSR+ 10 10 PSSR– 0 0 PSSR– 1M 10M –20 100 06742-024 100k PSSR+ –10 FREQUENCY (Hz) 1k 10k 100k 1M 10M FREQUENCY (Hz) Figure 24. PSRR vs. Frequency, VSY = 5 V Figure 27. PSRR vs. Frequency, VSY = 16 V 80 80 VSY = 5V TA = 25°C 70 VSY = 16V TA = 25°C 60 OS– 50 40 OS+ 30 40 30 OS– 20 20 10 10 CAPACITANCE (pF) 1k 0 10 06742-025 100 OS+ 50 100 CAPACITANCE (pF) Figure 25. Small-Signal Overshoot vs. Load Capacitance, VSY = 5 V 1k 06742-028 OVERSHOOT (%) 60 OVERSHOOT (%) VSY = 16V TA = 25°C 30 20 10k 10M 40 20 1k 1M 80 60 –10 100k 90 70 0 10 10k Figure 26. Closed-Loop Output Impedance vs. Frequency, VSY = 16 V 70 30 1k FREQUENCY (Hz) VSY = 5V TA = 25°C 80 PSRR (dB) 0.1 100 06742-027 10k 06742-040 1k 06742-041 1 0.1 100 70 VSY = 16V TA = 25°C G=1 ZOUT (Ω) ZOUT (Ω) G=1 –20 100 G = 10 VSY = 5V TA = 25°C Figure 28. Small-Signal Overshoot vs. Load Capacitance, VSY = 16 V Rev. D | Page 9 of 15 AD8663/AD8667/AD8669 Data Sheet 06742-029 VSY = ±2.5V AV = 1 CL = 200pF RL = 2kΩ TIME (10µs/DIV) 06742-032 VOLTAGE (2V/DIV) VOLTAGE (200mV/DIV) VSY = ±8V AV = 1 CL = 200pF RL = 2kΩ TIME (20µs/DIV) Figure 29. Large Signal Transient Response, VSY = ±2.5 V Figure 32. Large Signal Transient Response, VSY = ±8 V VSY = ±2.5V AV = 1 CL = 200pF RL = 10kΩ TIME (2µs/DIV) 06742-033 06742-030 VOLTAGE (50mV/DIV) VOLTAGE (50mV/DIV) VSY = ±8V AV = 1 CL = 200pF RL = 10kΩ TIME (2µs/DIV) Figure 30. Small Signal Transient Response, VSY = ±2.5 V Figure 33. Small Signal Transient Response, VSY = ±8 V 300 1200 TA = +125°C TA = +25°C ISY (µA) TA = –40°C 150 TA = +25°C 600 100 400 50 200 0 0 2 4 6 8 10 12 TA = +85°C 800 14 VSY (V) 16 06742-042 ISY (µA) 200 TA = +125°C 1000 TA = +85°C Figure 31. AD8663, Supply Current vs. Supply Voltage TA = –40°C 0 0 2 4 6 8 10 12 14 VSY (V) Figure 34. AD8669, Supply Current vs. Supply Voltage Rev. D | Page 10 of 15 16 06742-043 250 Data Sheet AD8663/AD8667/AD8669 1000 600 +85°C 500 +25°C 450 400 100 –40°C en (nV/ Hz) ISY (µA) VSY = ±2.5V AND ±8V TA = 25°C +125°C 550 350 300 250 200 10 150 100 4 6 8 10 12 14 16 VSY (V) 1 0 1.5 1.0 0.5 0 –0.10 –0.5 –1.0 –1.5 OUTPUT VOLTAGE –0.15 –2.0 –0.20 –2.5 17 0 12 –0.05 7 –0.10 2 –3 –0.15 06742-049 –0.25 Figure 36. Positive Overload Recovery –8 –13 TIME (20µs/DIV) Figure 39. Positive Overload Recovery 7.0 0.05 22 0.05 –0.20 –3.5 TIME (20µs/DIV) INPUT VOLTAGE OUTPUT VOLTAGE –3.0 –0.25 VSY = ±8V AV = –100 TA = 25°C 0.10 INPUT VOLTAGE (50mV/DIV) 0.05 –0.05 10000 27 0.15 3.5 3.0 2.5 2.0 INPUT VOLTAGE 1000 4.0 OUTPUT VOLTAGE (1V/DIV) INPUT VOLTAGE (50mV/DIV) 0.10 100 Figure 38. Voltage Noise Density 4.5 VSY = ±2.5V AV = –100 TA = 25°C 10 FREQUENCY (Hz) Figure 35. AD8667, Supply Current vs. Supply Voltage 0.15 1 OUTPUT VOLTAGE (5V/DIV) 2 06742-046 0 06742-031 0 06742-034 50 35 0.05 VSY = ±2.5V AV = –100 TA = 25°C –0.10 4.0 3.5 –0.15 3.0 2.5 –0.20 2.0 –0.25 1.5 1.0 OUTPUT VOLTAGE –0.30 –1.0 25 –0.10 20 –0.15 15 –0.20 10 5 –0.25 OUTPUT VOLTAGE 0 TIME (20µs/DIV) VSY = ±8V AV = –100 TA = 25°C –0.05 0.5 –0.5 –0.35 INPUT VOLTAGE OUTPUT VOLTAGE (5V/DIV) INPUT VOLTAGE 30 0 0 –0.30 –0.35 TIME (20µs/DIV) Figure 40. Negative Overload Recovery Figure 37. Negative Overload Recovery Rev. D | Page 11 of 15 –5 06742-048 –0.05 5.5 5.0 4.5 INPUT VOLTAGE (50mV/DIV) 6.0 OUTPUT VOLTAGE (1V/DIV) 0 06742-050 INPUT VOLTAGE (50mV/DIV) 6.5 AD8663/AD8667/AD8669 Data Sheet 0 0 VSY = ±2.5V TA = 25°C 20kΩ –40 –60 –80 –100 –120 2kΩ –40 –60 –80 –100 –120 –140 1k 10k FREQUENCY (Hz) 100k Figure 41. Channel Separation vs. Frequency –160 100 1k 10k FREQUENCY (Hz) Figure 42. Channel Separation vs. Frequency Rev. D | Page 12 of 15 100k 06742-047 –140 –160 100 VSY = ±8V TA = 25°C 20kΩ –20 CHANNEL SEPARATION (dB) 2kΩ 06742-051 CHANNEL SEPARATION (dB) –20 Data Sheet AD8663/AD8667/AD8669 OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890) 4.00 (0.1574) 3.80 (0.1497) 8 1 5 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY 0.10 SEATING PLANE 6.20 (0.2441) 5.80 (0.2284) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) 0.50 (0.0196) 0.25 (0.0099) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) 012407-A COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 43. 8-Lead Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 1.84 1.74 1.64 3.10 3.00 SQ 2.90 1.55 1.45 1.35 EXPOSED PAD 0.50 0.40 0.30 0.80 0.75 0.70 0.30 0.25 0.20 1 4 BOTTOM VIEW TOP VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.203 REF PIN 1 INDICATOR (R 0.15) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-229-WEED Figure 44. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD] 3 mm × 3 mm and 0.75 mm Package Height (CP-8-13) Dimensions shown in millimeters Rev. D | Page 13 of 15 12-07-2010-A PIN 1 INDEX AREA SEATING PLANE 0.50 BSC 8 5 AD8663/AD8667/AD8669 Data Sheet 3.20 3.00 2.80 8 3.20 3.00 2.80 5.15 4.90 4.65 5 1 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15° MAX 1.10 MAX 6° 0° 0.40 0.25 0.80 0.55 0.40 0.23 0.09 10-07-2009-B 0.15 0.05 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 45. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 8.75 (0.3445) 8.55 (0.3366) 8 14 1 7 6.20 (0.2441) 5.80 (0.2283) 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 0.50 (0.0197) 0.25 (0.0098) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 0.51 (0.0201) 0.31 (0.0122) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 060606-A 4.00 (0.1575) 3.80 (0.1496) Figure 46. 14-Lead Small Outline Package [SOIC_N] Narrow Body (R-14) Dimensions shown in millimeters and (inches) 5.10 5.00 4.90 14 8 4.50 4.40 4.30 6.40 BSC 1 7 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 COPLANARITY 0.10 0.30 0.19 0.20 0.09 SEATING PLANE 8° 0° COMPLIANT TO JEDEC STANDARDS MO-153-AB-1 Figure 47. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters Rev. D | Page 14 of 15 0.75 0.60 0.45 061908-A 1.05 1.00 0.80 Data Sheet AD8663/AD8667/AD8669 ORDERING GUIDE Model 1 AD8663ARZ AD8663ARZ-REEL AD8663ARZ-REEL7 AD8663ACPZ-R2 AD8663ACPZ-REEL7 AD8667ARZ AD8667ARZ-REEL AD8667ARZ-REEL7 AD8667ARMZ AD8667ARMZ-REEL AD8669ARZ AD8669ARZ-REEL AD8669ARZ-REEL7 AD8669ARUZ AD8669ARUZ-REEL 1 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead LFCSP 8-Lead LFCSP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead MSOP 8-Lead MSOP 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead TSSOP 14-Lead TSSOP Z = RoHS Compliant Part. ©2007–2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06742-0-5/16(D) Rev. D | Page 15 of 15 Package Option R-8 R-8 R-8 CP-8-13 CP-8-13 R-8 R-8 R-8 RM-8 RM-8 R-14 R-14 R-14 RU-14 RU-14 Branding A1U A1U A1E A1E