ADA4897-1: Microcircuit, Linear, Low Power Output Amplifiers, Monolithic Silicon - Military Datasheet (Rev. A) PDF

REVISIONS
LTR
DESCRIPTION
DATE
Prepared in accordance with ASME Y14.24
APPROVED
Vendor item drawing
REV
PAGE
REV
PAGE
18
19
REV STATUS
OF PAGES
20
21
22
REV
PAGE
1
2
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
13-07-02
4
A
REV
5
6
7
8
9
10
11
12
13
14
15
16
17
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
TITLE
MICROCIRCUIT, LINEAR, LOW POWER OUTPUT
AMPLIFIERS, MONOLITHIC SILICON
APPROVED BY
CHARLES F. SAFFLE
SIZE
AMSC N/A
3
CODE IDENT. NO.
DWG NO.
V62/13614
16236
PAGE
1
OF
22
5962-V057-13
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance low power output amplifiers microcircuit, with
an operating temperature range of -55°C to +125°C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/13614
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
02
Circuit function
ADA4897-1-EP
ADA4897-2-EP
Single low power output amplifier
Dual low power output amplifier
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
Y
6
10
JEDEC PUB 95
Package style
MO-178-AB
MO-187-BA
Plastic small outline package
Plastic small outline package
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer:
Finish designator
A
B
C
D
E
Z
DLA LAND AND MARITIME
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage (VS) .................................................................................................... 11 V
Common mode input voltage (VCM) ...........................................................................
Differential input voltage .............................................................................................
Power dissipation (PD) :
Device type 01 .......................................................................................................
Device type 02 .......................................................................................................
Storage temperature range (TSTG) ............................................................................
Lead temperature (soldering 10 seconds) ..................................................................
Junction temperature range (TJ) ................................................................................
-VS – 0.7 V to +VS + 0.7 V
±0.7 V
166.6 mW 2/
119.0 mW 2/
-65°C to +125°C
+300°C
+150°C
1.4 Recommended operating conditions. 3/
Supply voltage range (VS) .......................................................................................... -5 V to +5 V
Operating free-air temperature range (TA) ................................................................. -55°C to +125°C
1.5 Thermal characteristics.
Thermal resistance, junction to ambient (θJA):
X package ............................................................................................................... 150°C/W
Y package ............................................................................................................... 210°C/W
1/
2/
3/
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
For device type 01, power dissipation (PD) = ( TJ max – TA ) / θJA = (150 – 125) / 150 = 0.16666 W.
For device type 02, power dissipation (PD) = ( TJ max – TA ) / θJA = (150 – 125) / 210 = 0.1190 W.
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
3
2. APPLICABLE DOCUMENTS
JEDEC Solid State Technology Association
JEDEC PUB 95
–
Registered and Standard Outlines for Semiconductor Devices
(Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA
22201-3834 or online at http://www.jedec.org)
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
4
TABLE I. Electrical performance characteristics. 1/ 2/
Test
Symbol
Conditions
VS = ±5 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to ground,
unless otherwise specified
Unit
Max
Dynamic performance section.
-3 dB bandwidth
BW
Bandwidth for 0.1 dB
flatness
+25°C
G = +1, VOUT = 0.02 VPP
01, 02
230 typical
G = +1, VOUT = 2 VPP
30 typical
G = +2, VOUT = 0.02 VPP
90 typical
G = +2, VOUT = 2 VPP,
MHz
+25°C
01, 02
7 typical
MHz
RL = 100 Ω
Slew rate
SR
G = +2, VOUT = 6 V step
+25°C
01, 02
120 typical
V/µs
Settling time to 0.1%
tS
G = +2, VOUT = 2 V step
+25°C
01, 02
45 typical
ns
Settling time to 0.01%
tS
G = +2, VOUT = 2 V step
+25°C
01, 02
90 typical
ns
+25°C
01, 02
-115 typical
dBc
Noise / harmonic performance section.
Harmonic distortion
SFDR
Input voltage noise
VOUT = 2 VPP, fC = 100 kHz
VOUT = 2 VPP, fC = 1 MHz
-93 typical
VOUT = 2 VPP, fC = 2 MHz
-80 typical
VOUT = 2 VPP, fC = 5 MHz
-61 typical
f = 10 Hz
+25°C
01, 02
f = 100 kHz
Input current noise
nV /
Hz
1 typical
f = 10 Hz
+25°C
01, 02
f = 100 kHz
0.1 Hz to 10 Hz noise
2.4 typical
11 typical
pA /
Hz
2.8 typical
G = +101, RF = 1 kΩ, RG = 10 Ω
+25°C
01, 02
99 typical
nVPP
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions
VS = ±5 V, G = +1,
Temperature,
TA
Device
type
RL = 1 kΩ to ground,
unless otherwise specified
Limits
Unit
Min
Max
-500
+500
DC performance section.
Input offset voltage
+25°C
VIO
01, 02
µV
-28 typical
Input offset voltage drift
∆VIO
+25°C
01, 02
Input bias current
IIB
+25°C
01, 02
0.2 typical
-17
µV /
°C
µA
-4
-11 typical
Input bias current drift
∆IIB
+25°C
01, 02
Input bias offset current
IIBO
+25°C
01, 02
3 typical
-0.6
nA /
°C
µA
+0.6
-0.02 typical
Open loop gain
AOL
+25°C
VOUT = -4 V to +4 V
01, 02
100
dB
110 typical
Input characteristics section.
Input resistance,
common mode
RIN
+25°C
01, 02
10 typical
MΩ
Input resistance,
differential
RIN
+25°C
01, 02
10 typical
kΩ
Input capacitance,
common mode
CIN
+25°C
01, 02
3 typical
pF
Input capacitance,
differential
CIN
+25°C
01, 02
11 typical
pF
Input common mode
voltage range
VINR
+25°C
01, 02
-4.9 to +4.1
typical
V
Common mode
rejection ratio
CMRR
+25°C
01, 02
VCM = -2 V to +2 V
-92
dB
-120 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions
VS = ±5 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to ground,
unless otherwise specified
Unit
Max
Output characteristics section.
Output overdrive
recovery time
VIN = ±5 V, G = + 2
+25°C
01, 02
Positive output
voltage swing
RL = 1 kΩ
+25°C
01, 02
81 typical
ns
4.85
V
4.96 typical
4.5
RL = 100 Ω
4.73 typical
Negative output
voltage swing
+25°C
RL = 1 kΩ
01, 02
-4.85
V
-4.97 typical
-4.5
RL = 100 Ω
-4.84 typical
Output current
IOUT
SFDR = -45 dBc
+25°C
01, 02
80 typical
mA
Short circuit current
ISC
Sinking / sourcing
+25°C
01, 02
135 typical
mA
30% overshoot, G = +2
+25°C
01, 02
39 typical
pF
Operating range
+25°C
01, 02
3 to 10 typical
V
Quiescent current
per amplifier
+25°C
01, 02
2.8
Capacitive load drive
Power supply section.
3.2
mA
3.0 typical
0.25
DISABLE = -5 V
0.13 typical
Power supply
rejection ratio
+PSRR
+25°C
+VS = 4 V to 6 V, -VS = -5 V
01, 02
-96
dB
-125 typical
-PSRR
-96
+VS = 5 V, -VS = -4 V to -6 V
-121 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
7
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions
VS = ±5 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to ground,
unless otherwise specified
Unit
Max
DISABLE pin section.
Enabled
DISABLE voltage
+25°C
01, 02
Disabled
V
>+VS – 0.5
typical
<+VS – 2 typical
Input current, enabled
IIN
DISABLE = +5 V
+25°C
01, 02
-1.2 typical
µA
Input current, disabled
IIN
DISABLE = -5 V
+25°C
01, 02
-40 typical
µA
Switching speed,
enabled
+25°C
01, 02
0.25 typical
µs
Switching speed,
disabled
+25°C
01, 02
12 typical
µs
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
8
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +5 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Max
Dynamic performance section.
-3 dB bandwidth
BW
Bandwidth for 0.1 dB
flatness
+25°C
G = +1, VOUT = 0.02 VPP
01, 02
230 typical
G = +1, VOUT = 2 VPP
30 typical
G = +2, VOUT = 0.02 VPP
90 typical
G = +2, VOUT = 2 VPP,
MHz
+25°C
01, 02
7 typical
MHz
RL = 100 Ω
Slew rate
SR
G = +2, VOUT = 3 V step
+25°C
01, 02
100 typical
V/µs
Settling time to 0.1%
tS
G = +2, VOUT = 2 V step
+25°C
01, 02
45 typical
ns
Settling time to 0.01%
tS
G = +2, VOUT = 2 V step
+25°C
01, 02
95 typical
ns
+25°C
01, 02
-115 typical
dBc
Noise / harmonic performance section.
Harmonic distortion
SFDR
Input voltage noise
VOUT = 2 VPP, fC = 100 kHz
VOUT = 2 VPP, fC = 1 MHz
-93 typical
VOUT = 2 VPP, fC = 2 MHz
-80 typical
VOUT = 2 VPP, fC = 5 MHz
-61 typical
f = 10 Hz
+25°C
01, 02
f = 100 kHz
Input current noise
nV /
Hz
1 typical
f = 10 Hz
+25°C
01, 02
f = 100 kHz
0.1 Hz to 10 Hz noise
2.4 typical
11 typical
pA /
Hz
2.8 typical
G = +101, RF = 1 kΩ, RG = 10 Ω
+25°C
01, 02
99 typical
nVPP
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
9
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +5 V, G = +1,
Temperature,
TA
Device
type
RL = 1 kΩ to midsupply,
unless otherwise specified
Limits
Unit
Min
Max
-500
+500
DC performance section.
Input offset voltage
+25°C
VIO
01, 02
µV
-30 typical
Input offset voltage drift
∆VIO
+25°C
01, 02
Input bias current
IIB
+25°C
01, 02
0.2 typical
-17
-4
µV /
°C
µA
-11 typical
Input bias current drift
∆IIB
+25°C
01, 02
Input bias offset current
IIBO
+25°C
01, 02
3 typical
-0.6
+0.6
nA /
°C
µA
-0.02 typical
Open loop gain
AOL
+25°C
VOUT = 0.5 V to 4.5 V
01, 02
97
dB
110 typical
Input characteristics section.
Input resistance,
common mode
RIN
+25°C
01, 02
10 typical
MΩ
Input resistance,
differential
RIN
+25°C
01, 02
10 typical
kΩ
Input capacitance,
common mode
CIN
+25°C
01, 02
3 typical
pF
Input capacitance,
differential
CIN
+25°C
01, 02
11 typical
pF
Input common mode
voltage range
VINR
+25°C
01, 02
0.1 to 4.1
typical
V
Common mode
rejection ratio
CMRR
+25°C
01, 02
VCM = 1 V to 4 V
-91
dB
-118 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
10
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +5 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Max
Output characteristics section.
Output overdrive
recovery time
VIN = 0 V to 5 V, G = + 2
+25°C
01, 02
Positive output
voltage swing
RL = 1 kΩ
+25°C
01, 02
96 typical
4.85
ns
V
4.98 typical
4.8
RL = 100 Ω
4.88 typical
Negative output
voltage swing
+25°C
RL = 1 kΩ
01, 02
0.15
V
0.014 typical
0.2
RL = 100 Ω
0.08 typical
Output current
IOUT
SFDR = -45 dBc
+25°C
01, 02
70 typical
mA
Short circuit current
ISC
Sinking / sourcing
+25°C
01, 02
125 typical
mA
30% overshoot, G = +2
+25°C
01, 02
39 typical
pF
Operating range
+25°C
01, 02
3 to 10 typical
V
Quiescent current
per amplifier
+25°C
01, 02
2.6
Capacitive load drive
Power supply section.
2.9
mA
2.8 typical
0.18
DISABLE = 0 V
0.05 typical
Power supply
rejection ratio
+PSRR
+25°C
+VS = 4.5 V to 5.5 V, -VS = 0 V
01, 02
-96
dB
-123 typical
-PSRR
-96
+VS = 5 V, -VS = -0.5 V to +0.5 V
-121 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
11
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +5 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Max
DISABLE pin section.
Enabled
DISABLE voltage
+25°C
01, 02
Disabled
>+VS – 0.5
typical
V
<+VS – 2 typical
Input current, enabled
IIN
DISABLE = +5 V
+25°C
01, 02
-1.2 typical
µA
Input current, disabled
IIN
DISABLE = 0 V
+25°C
01, 02
-20 typical
µA
Switching speed,
enabled
+25°C
01, 02
0.25 typical
µs
Switching speed,
disabled
+25°C
01, 02
12 typical
µs
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
12
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +3 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Max
Dynamic performance section.
-3 dB bandwidth
BW
Bandwidth for 0.1 dB
flatness
+25°C
G = +1, VOUT = 0.02 VPP
01, 02
230 typical
G = -1, VOUT = 1 VPP
45 typical
G = +2, VOUT = 0.02 VPP
90 typical
G = +2, VOUT = 2 VPP,
MHz
+25°C
01, 02
7 typical
MHz
RL = 100 Ω
Slew rate
SR
G = +2, VOUT = 1 V step
+25°C
01, 02
85 typical
V/µs
Settling time to 0.1%
tS
G = +2, VOUT = 2 V step
+25°C
01, 02
45 typical
ns
Settling time to 0.01%
tS
G = +2, VOUT = 2 V step
+25°C
01, 02
96 typical
ns
+25°C
01, 02
-105 typical
dBc
Noise / harmonic performance section.
Harmonic distortion
SFDR
Input voltage noise
VOUT = 2 VPP, fC = 100 kHz,
G = +2
VOUT = 1 VPP, fC = 1 MHz, G = -1
-84 typical
VOUT = 1 VPP, fC = 2 MHz, G = -1
-77 typical
VOUT = 1 VPP, fC = 5 MHz, G = -1
-60 typical
f = 10 Hz
+25°C
01, 02
f = 100 kHz
Input current noise
1 typical
f = 10 Hz
+25°C
01, 02
f = 100 kHz
0.1 Hz to 10 Hz noise
2.3 typical
11 typical
2.8 typical
G = +101, RF = 1 kΩ, RG = 10 Ω
+25°C
01, 02
99 typical
nV /
Hz
pA /
Hz
nVPP
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
13
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +3 V, G = +1,
Temperature,
TA
Device
type
Limits
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Min
Max
-500
+500
DC performance section.
Input offset voltage
+25°C
VIO
01, 02
µV
-30 typical
Input offset voltage drift
∆VIO
+25°C
01, 02
Input bias current
IIB
+25°C
01, 02
0.2 typical
-17
-4
µV /
°C
µA
-11 typical
Input bias current drift
∆IIB
+25°C
01, 02
Input bias offset current
IIBO
+25°C
01, 02
3 typical
-0.6
+0.6
nA /
°C
µA
-0.02 typical
Open loop gain
AOL
+25°C
VOUT = 0.5 V to 2.5 V
01, 02
95
dB
108 typical
Input characteristics section.
Input resistance,
common mode
RIN
+25°C
01, 02
10 typical
MΩ
Input resistance,
differential
RIN
+25°C
01, 02
10 typical
kΩ
Input capacitance,
common mode
CIN
+25°C
01, 02
3 typical
pF
Input capacitance,
differential
CIN
+25°C
01, 02
11 typical
pF
Input common mode
voltage range
VINR
+25°C
01, 02
0.1 to 2.1 typical
V
Common mode
rejection ratio
CMRR
+25°C
01, 02
VCM = 1.1 V to 1.9 V
-90
dB
-124 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
14
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +3 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Max
Output characteristics section.
Output overdrive
recovery time
VIN = 0 V to 3 V, G = + 2
+25°C
01, 02
Positive output
voltage swing
RL = 1 kΩ
+25°C
01, 02
83 typical
2.85
ns
V
2.97 typical
2.8
RL = 100 Ω
2.92 typical
Negative output
voltage swing
+25°C
RL = 1 kΩ
01, 02
0.15
V
0.01 typical
0.2
RL = 100 Ω
0.05 typical
Output current
IOUT
SFDR = -45 dBc
+25°C
01, 02
60 typical
mA
Short circuit current
ISC
Sinking / sourcing
+25°C
01, 02
120 typical
mA
30% overshoot, G = +2
+25°C
01, 02
39 typical
pF
Operating range
+25°C
01, 02
3 to 10 typical
V
Quiescent current
per amplifier
+25°C
01, 02
2.5
Capacitive load drive
Power supply section.
2.9
mA
2.7 typical
0.15
DISABLE = 0 V
0.035 typical
Power supply
rejection ratio
+PSRR
+25°C
+VS = 2.7 V to 3.7 V, -VS = 0 V
01, 02
-96
dB
-121 typical
-PSRR
-96
+VS = 3 V, -VS = -0.3 V to +0.7 V
-120 typical
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
15
TABLE I. Electrical performance characteristics – Continued. 1/ 2/
Test
Symbol
Conditions 2/
VS = +3 V, G = +1,
Temperature,
TA
Device
type
Limits
Min
RL = 1 kΩ to midsupply,
unless otherwise specified
Unit
Max
DISABLE pin section.
Enabled
DISABLE voltage
+25°C
01, 02
Disabled
>+VS – 0.5
typical
V
<+VS + 2 typical
Input current, enabled
IIN
DISABLE = +3 V
+25°C
01, 02
-1.2 typical
µA
Input current, disabled
IIN
DISABLE = 0 V
+25°C
01, 02
-15 typical
µA
Switching speed,
enabled
+25°C
01, 02
0.25 typical
µs
Switching speed,
disabled
+25°C
01, 02
12 typical
µs
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
2/
Products supplied to this drawing have been characterized across the military temperature range of -55°C to +125°C but, are only
production tested at +25°C.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
16
Case X
FIGURE 1. Case outlines.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
17
Case X – continued.
Dimensions
Inches
Symbol
Millimeters
Min
Med
Max
Min
Med
Max
A
0.035
0.045
0.051
0.90
1.15
1.30
A1
0.001
---
0.005
0.05
---
0.15
A2
0.037
---
0.057
0.95
---
1.45
b
0.011
---
0.019
0.30
---
0.50
c
0.003
---
0.007
0.08
---
0.20
D
0.110
0.114
0.118
2.80
2.90
3.00
E
0.059
0.062
0.066
1.50
1.60
1.70
E1
0.102
0.110
0.118
2.60
2.80
3.00
e
L
L1
0.037 BSC
0.013
0.017
0.95 BSC
0.021
0.35
0.023 BSC
0.45
0.55
0.60 BSC
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. Falls within reference to JEDEC MO-178-AB.
FIGURE 1. Case outlines - continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
18
Case Y
FIGURE 1. Case outlines - Continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
19
Case Y – continued.
Dimensions
Inches
Symbol
Millimeters
Min
Med
Max
Min
Med
Max
A
---
---
0.043
---
---
1.10
A1
0.001
---
0.005
0.05
---
0.15
A2
0.029
0.033
0.037
0.75
0.85
0.95
b
0.05
---
0.011
0.15
---
0.30
c
0.005
---
0.009
0.13
---
0.23
D
0.114
0.118
0.122
2.90
3.00
3.10
E
0.114
0.118
0.122
2.90
3.00
3.10
E1
0.183
0.192
0.202
4.65
4.90
5.15
e
L
0.019 BSC
0.015
0.021
0.50 BSC
0.027
0.40
0.55
0.70
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. Falls within reference to JEDEC MO-187-BA.
FIGURE 1. Case outlines - Continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
20
Device type
01
Case outline
X
Terminal number
Terminal
symbol
Description
1
OUT
Output.
2
-VS
Negative supply.
3
+IN
Noninverting input.
4
-IN
Inverting input.
5
DISABLE
6
+VS
Disable.
Positive supply.
Device type
02
Case outline
Y
Terminal number
Terminal
symbol
Description
1
OUT1
2
-IN1
Inverting input 1.
3
+IN1
Noninverting input 1.
4
-VS
Negative supply.
5
DISABLE1
Disable 1.
6
DISABLE2
Disable 2.
7
+IN2
Noninverting input 2.
8
-IN2
Inverting input 2.
9
OUT2
10
+VS
Output 1.
Output 2.
Positive supply.
FIGURE 2. Terminal connections.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
21
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Vendor part number
V62/13614-01XE
24355
ADA4897-1SRJZ-EPR7
V62/13614-02YE
24355
ADA4897-2TRMZ-EP
1/ The vendor item drawing establishes an administrative control number
for identifying the item on the engineering documentation.
CAGE code
24355
DLA LAND AND MARITIME
COLUMBUS, OHIO
Source of supply
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: Raheen Business Park
Limerick, Ireland
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/13614
PAGE
22
Similar pages