24VL024/24VL025 2K I2C™ Serial EEPROM Device Selection Table Description: Part Number VCC Range Max Clock 24VL024 1.5 to 3.6V 400 kHz(1) 24VL025 1.5 to 3.6V 400 kHz(1) Note 1: 100 kHz for VCC < 1.8V Features: • Single-Supply with Operation down to 1.5V • Low-Power CMOS Technology: - 400 μA active current, maximum - 1 μA standby current, maximum • 2-Wire Serial Interface Bus, I2C™ Compatible • Schmitt Trigger Inputs for Noise Suppression • Output Slope Control to Eliminate Ground Bounce • 100 kHz and 400 kHz Compatibility • Page Write Buffer for up to 16 Bytes • Self-Timed Write Cycle (including Auto-Erase) • Hardware Write Protection for the Entire Array (24VL024 only) • Cascadable up to Eight Devices • More than 1 Million Erase/Write Cycles • ESD Protection > 4,000V • Data Retention > 200 Years • Factory Programming (QTP) Available • 8-pin PDIP, SOIC, TSSOP, TDFN and MSOP Packages • 6-lead SOT-23 package (24VL025 only) • Temperature Range: - -20°C to +85°C The Microchip Technology Inc. 24VL024/24VL025 is a 2 Kbit Serial Electrically Erasable PROM with operation down to 1.5V. The device is organized as a single block of 256 x 8-bit memory with a 2-wire serial interface. Low-current design permits operation with maximum standby and active currents of only 1 μA and 400 μA, respectively. The device has a page write capability for up to 16 bytes of data. Functional address lines allow the connection of up to eight 24VL024/ 24VL025 devices on the same bus for up to 16 Kbits of contiguous EEPROM memory. The device is available in the standard 8-pin PDIP, 8-pin SOIC (150 mil), TSSOP, 2x3 TDFN and MSOP packages. The 24VL025 is also available in the 6-lead, SOT-23 package. Block Diagram WP A0 A1 A2 HV Generator I/O Control Logic Memory Control Logic EEPROM Array XDEC SDA SCL Write-Protect Circuitry YDEC VCC VSS Sense Amp. R/W Control Package Types SOIC, TSSOP PDIP, MSOP • Pb-Free and RoHS Compliant A0 1 8 VCC A0 1 8 VCC A1 2 7 WP A1 2 7 WP A2 3 6 SCL A2 3 6 SCL VSS 4 5 SDA VSS 4 5 SDA SOT-23 TDFN A0 1 A1 2 A2 3 VSS 4 8 VCC 7 WP 6 SCL 5 SDA SCL 1 6 VCC VSS 2 5 A0 SDA 3 4 A1 (24VL025 only) Note: © 2009 Microchip Technology Inc. WP pin is not internally connected on the 24VL025 DS22130A-page 1 24VL024/24VL025 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings (†) VCC .............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65°C to +150°C Ambient temperature with power applied ..................................................................................................-20°C to +85°C ESD protection on all pins ......................................................................................................................................................≥ 4 kV † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS DC CHARACTERISTICS Param. No. Sym. Characteristic Electrical Characteristics: VCC = +1.5V to 3.6V TA = -20°C to +85°C Min. Max. Units Conditions — — — D1 — A0, A1, A2, SCL, SDA and WP pins: — D2 VIH High-level input voltage 0.7 VCC — V — D3 VIL Low-level input voltage — 0.3 VCC V — D4 VHYS Hysteresis of Schmitt Trigger inputs (SDA, SCL pins) 0.05 VCC — V (Note) D5 VOL Low-level output voltage — 0.40 V IOL = 3.0 mA @ VCC = 3.6V IOL = 2.1 mA @ VCC = 2.5V D6 ILI Input leakage current — ±1 μA VIN = VSS or VCC, WP = VSS D7 ILO Output leakage current — ±1 μA VOUT = VSS or VCC D8 CIN, COUT Pin capacitance (all inputs/outputs) — 10 pF VCC = 3.6V (Note) TA = 25°C, f = 1 MHz D9 ICC Read Operating current — 400 μA VCC = 3.6V, SCL = 400 kHz — 3 mA VCC = 3.6V D10 ICCS — 1 μA VCC = 3.6V, SCL = SDA = VCC WP = VSS, A0, A1, A2 = VSS ICC Write Note: Standby current This parameter is periodically sampled and not 100% tested. DS22130A-page 2 © 2009 Microchip Technology Inc. 24VL024/24VL025 TABLE 1-2: AC CHARACTERISTICS Electrical Characteristics: VCC = +1.5V to 3.6V TA = -20°C to +85°C AC CHARACTERISTICS Param. Symbol No. Characteristic Min. Max. Units Conditions 1 FCLK Clock frequency — — 100 400 kHz 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 2 THIGH Clock high time 4000 600 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 3 TLOW Clock low time 4700 1300 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 4 TR SDA and SCL rise time (Note 1) — — 1000 300 ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 5 TF SDA and SCL fall time (Note 1) — — 1000 300 ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 6 THD:STA Start condition hold time 4000 600 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 7 TSU:STA Start condition setup time 4700 600 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 8 THD:DAT Data input hold time 0 — ns (Note 2) 9 TSU:DAT Data input setup time 250 100 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 10 TSU:STO Stop condition setup time 4000 600 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 11 TSU:WP WP setup time (Note 5) 4000 600 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 12 THD:WP WP hold time (Note 5) 4700 600 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 13 TAA Output valid from clock (Note 2) — — 3500 900 ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 14 TBUF Bus free time: Time the bus must be free before a new transmission can start 4700 1300 — — ns 1.5V ≤ VCC < 1.8V 1.8V ≤ VCC ≤ 3.6V 15 TSP Input filter spike suppression (SDA and SCL pins) — 50 ns (Note 1 and Note 3) 16 TWC Write cycle time (byte or page) — 5 ms — 17 — Endurance 1M — cycles 25°C, VCC = 3.6V, per page (Note 4) Note 1: Not 100% tested. CB = total capacitance of one bus line in pF. 2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions. 3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved noise spike suppression. This eliminates the need for a TI specification for standard operation. 4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com. 5: 24VL024 only. © 2009 Microchip Technology Inc. DS22130A-page 3 24VL024/24VL025 FIGURE 1-1: BUS TIMING DATA 5 SCL 7 SDA In 3 4 D4 2 8 10 9 6 15 14 13 SDA Out WP DS22130A-page 4 (protected) (unprotected) 11 12 © 2009 Microchip Technology Inc. 24VL024/24VL025 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE 8-pin PDIP 8-pin SOIC 8-pin TSSOP 8-pin MSOP 8-pin TDFN 6-pin SOT-23 A0 1 1 1 1 1 5 User Configurable Chip Select A1 2 2 2 2 2 4 User Configurable Chip Select A2 3 3 3 3 3 — User Configurable Chip Select VSS 4 4 4 4 4 2 Ground Name Function SDA 5 5 5 5 5 3 Serial Data SCL 6 6 6 6 6 1 Serial Clock WP 7 7 7 7 7 — Write-Protect Input VCC 8 8 8 8 8 6 +1.5V to 3.6V 2.1 SDA Serial Data 2.4 WP (24VL024 only) This is a bidirectional pin used to transfer addresses and data into and out of the device. It is an open drain terminal. Therefore, the SDA bus requires a pull-up resistor to VCC (typical 10 kΩ for 100 kHz, 2 kΩ for 400 kHz). WP is the hardware write-protect pin. It must be tied to VCC or VSS. If tied to VCC, the hardware write protection is enabled and will protect the entire array (00h-FFh). If the WP pin is tied to VSS the hardware write protection is disabled. For normal data transfer, SDA is allowed to change only during SCL low. Changes during SCL high are reserved for indicating the Start and Stop conditions. 2.5 2.2 SCL Serial Clock The SCL input is used to synchronize the data transfer to and from the device. 2.3 Noise Protection The 24VL024/24VL025 employs a VCC threshold detector circuit that disables the internal erase/write logic if the VCC is below 1.0 volts at nominal conditions. The SCL and SDA inputs have Schmitt Trigger and filter circuits that suppress noise spikes to assure proper device operation even on a noisy bus. A0, A1, A2 The A0, A1 and A2 inputs are used by the 24VL024/ 24VL025 for multiple device operations. The levels on these inputs are compared with the corresponding bits in the slave address. The chip is selected if the compare is true. Up to eight 24VL024/24VL025 devices (four for the SOT-23 package) may be connected to the same bus by using different Chip Select bit combinations. These inputs must be connected to either VCC or VSS. In most applications, the chip address inputs A0, A1 and A2 are hard-wired to logic ‘0’ or logic ‘1’. For applications in which these pins are controlled by a microcontroller or other programmable device, the chip address pins must be driven to logic ‘0’ or logic ‘1’ before normal device operation can proceed. © 2009 Microchip Technology Inc. DS22130A-page 5 24VL024/24VL025 3.0 FUNCTIONAL DESCRIPTION The 24VL024/24VL025 supports a bidirectional, 2-wire bus and data transmission protocol. A device that sends data onto the bus is defined as transmitter, and a device receiving data as receiver. The bus has to be controlled by a master device that generates the Serial Clock (SCL), controls the bus access and generates the Start and Stop conditions, while the 24VL024/ 24VL025 works as slave. Both master and slave can operate as transmitter or receiver, but the master device determines which mode is activated. DS22130A-page 6 © 2009 Microchip Technology Inc. 24VL024/24VL025 4.0 BUS CHARACTERISTICS The data on the line must be changed during the low period of the clock signal. There is one bit of data per clock pulse. The following bus protocol has been defined: • Data transfer may be initiated only when the bus is not busy. • During data transfer, the data line must remain stable whenever the clock line is high. Changes in the data line while the clock line is high will be interpreted as a Start or Stop condition. Accordingly, the following bus conditions have been defined (Figure 4-1). Each data transfer is initiated with a Start condition and terminated with a Stop condition. The number of the data bytes transferred between the Start and Stop conditions is determined by the master device and is, theoretically, unlimited, though only the last sixteen will be stored when doing a write operation. When an overwrite does occur, it will replace data in a first-in first-out fashion. 4.1 4.5 Bus Not Busy (A) Each receiving device, when addressed, is required to generate an acknowledge after the reception of each byte. The master device must generate an extra clock pulse which is associated with this Acknowledge bit. Both data and clock lines remain high. 4.2 Start Data Transfer (B) A high-to-low transition of the SDA line while the clock (SCL) is high determines a Start condition. All commands must be preceded by a Start condition. 4.3 Note: A low-to-high transition of the SDA line while the clock (SCL) is high determines a Stop condition. All operations must be ended with a Stop condition. Data Valid (D) The state of the data line represents valid data when, after a Start condition, the data line is stable for the duration of the high period of the clock signal. FIGURE 4-1: SCL (A) The 24VL024/24VL025 does not generate any Acknowledge bits if an internal programming cycle is in progress. The device that acknowledges has to pull down the SDA line during the Acknowledge clock pulse in such a way that the SDA line is stable low during the high period of the acknowledge-related clock pulse. Of course, setup and hold times must be taken into account. A master must signal an end of data to the slave by not generating an Acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave must leave the data line high to enable the master to generate the Stop condition (Figure 4-2). Stop Data Transfer (C) 4.4 Acknowledge DATA TRANSFER SEQUENCE ON THE SERIAL BUS CHARACTERISTICS (B) (C) (D) (C) (A) SDA Start Condition FIGURE 4-2: Address or Acknowledge Valid Stop Condition Data Allowed to Change ACKNOWLEDGE TIMING Acknowledge Bit SCL SDA 1 2 3 4 5 6 7 Data from transmitter Transmitter must release the SDA line at this point allowing the Receiver to pull the SDA line low to acknowledge the previous eight bits of data. © 2009 Microchip Technology Inc. 8 9 1 2 3 Data from transmitter Receiver must release the SDA line at this point so the Transmitter can continue sending data. DS22130A-page 7 24VL024/24VL025 5.0 DEVICE ADDRESSING A control byte is the first byte received following the Start condition from the master device (Figure 5-1). The control byte consists of a four-bit control code; for the 24VL024/24VL025 this is set as ‘1010’ binary for read and write operations. The next three bits of the control byte are the Chip Select bits (A2, A1, A0). The Chip Select bits allow the use of up to eight 24VL024/ 24VL025 devices on the same bus and are used to select which device is accessed. The Chip Select bits in the control byte must correspond to the logic levels on the corresponding A2, A1 and A0 pins for the device to respond. These bits are in effect the three Most Significant bits of the word address. For the SOT-23 package, the A2 pin is not connected. During device addressing, the A2 chip select bit should be set to logic ‘0’. Only four 24VL025 SOT-23 devices can be connected to the same bus. The last bit of the control byte defines the operation to be performed. When set to a ‘1’, a read operation is selected. When set to a ‘0’, a write operation is selected. Following the Start condition, the 24VL024/ 24VL025 monitors the SDA bus, checking the control byte being transmitted. Upon receiving a ‘1010’ code and appropriate Chip Select bits, the slave device outputs an Acknowledge signal on the SDA line. Depending on the state of the R/W bit, the 24VL024/ 24VL025 will select a read or write operation. DS22130A-page 8 FIGURE 5-1: CONTROL BYTE FORMAT Read/Write Bit Chip Select Bits Control Code S 1 0 1 0 A2 A1 A0 R/W ACK Slave Address Start Bit 5.1 Acknowledge Bit Contiguous Addressing Across Multiple Devices The Chip Select bits A2, A1 and A0 can be used to expand the contiguous address space for up to 16K bits by adding up to eight 24VL024/24VL025 devices on the same bus. In this case, software can use A0 of the control byte as address bit A8, A1 as address bit A9, and A2 as address bit A10. It is not possible to sequentially read across device boundaries. For the SOT-23 package, up to four devices can be added for up to 8K bits of address space. In this case, software can use A0 of the control byte as address bit A8, and A1 as address bit A9. Bit A2 of the control byte must always be set to logic ‘0’ for the SOT-23 package. © 2009 Microchip Technology Inc. 24VL024/24VL025 6.0 WRITE OPERATIONS 6.1 Byte Write The higher order four bits of the word address remain constant. If the master should transmit more than 16 bytes prior to generating the Stop condition, the address counter will roll over and the previously received data will be overwritten. As with the byte write operation, once the Stop condition is received, an internal write cycle will begin (Figure 6-2). If an attempt is made to write to the protected portion of the array when the hardware write protection has been enabled, the device will acknowledge the command, but no data will be written. The write cycle time must be observed even if write protection is enabled. Following the Start signal from the master, the device code (4 bits), the Chip Select bits (3 bits) and the R/W bit (which is a logic low) are placed onto the bus by the master transmitter. The device will acknowledge this control byte during the ninth clock pulse. The next byte transmitted by the master is the word address and will be written into the Address Pointer of the 24VL024/ 24VL025. After receiving another Acknowledge signal from the 24VL024/24VL025, the master device will transmit the data word to be written into the addressed memory location. The 24VL024/24VL025 acknowledges again and the master generates a Stop condition. This initiates the internal write cycle and the 24VL024/24VL025 will not generate Acknowledge signals during this time (Figure 6-1). If an attempt is made to write to the protected portion of the array when the hardware write protection has been enabled, the device will acknowledge the command, but no data will be written. The write cycle time must be observed even if write protection is enabled. 6.2 Note: Page Write The write-control byte, word address and the first data byte are transmitted to the 24VL024/24VL025 in the same way as in a byte write. But instead of generating a Stop condition, the master transmits up to 15 additional data bytes to the 24VL024/24VL025 that are temporarily stored in the on-chip page buffer and will be written into the memory once the master has transmitted a Stop condition. Upon receipt of each word, the four lower order Address Pointer bits are internally incremented by one. FIGURE 6-1: 6.3 Page write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. Physical page boundaries start at addresses that are integer multiples of the page buffer size (or ‘page size’) and end at addresses that are integer multiples of [page size – 1]. If a Page Write command attempts to write across a physical page boundary, the result is that the data wraps around to the beginning of the current page (overwriting data previously stored there), instead of being written to the next page, as might be expected. It is therefore necessary that the application software prevent page write operations that would attempt to cross a page boundary. Write Protection (24VL024 only) The WP pin must be tied to VCC or VSS. If tied to VCC, the entire array will be write-protected (00h-FFh). If the WP pin is tied to VSS, write operations to all address locations are allowed. BYTE WRITE Bus Activity Master S T A R T SDA Line S Control Byte Word Address S T O P Data P A C K Bus Activity FIGURE 6-2: A C K A C K PAGE WRITE Bus Activity Master S T A R T SDA Line S Control Byte Bus Activity © 2009 Microchip Technology Inc. Word Address (n) Data (n) S T O P Data (n + 15) Data (n +1) P A C K A C K A C K A C K A C K DS22130A-page 9 24VL024/24VL025 7.0 ACKNOWLEDGE POLLING Since the device will not acknowledge during a write cycle, this can be used to determine when the cycle is complete (this feature can be used to maximize bus throughput). Once the Stop condition for a write command has been issued from the master, the device initiates the internally-timed write cycle and ACK polling can be initiated immediately. This involves the master sending a Start condition followed by the control byte for a Write command (R/W = 0). If the device is still busy with the write cycle, no ACK will be returned. If no ACK is returned, the Start bit and control byte must be re-sent. If the cycle is complete, the device will return the ACK and the master can then proceed with the next Read or Write command. See Figure 7-1 for a flow diagram of this operation. FIGURE 7-1: ACKNOWLEDGE POLLING FLOW Send Write Command Send Stop Condition to Initiate Write Cycle Send Start Send Control Byte with R/W = 0 Did Device Acknowledge (ACK = 0)? No Yes Next Operation DS22130A-page 10 © 2009 Microchip Technology Inc. 24VL024/24VL025 8.0 READ OPERATIONS Read operations are initiated in the same way as write operations, with the exception that the R/W bit of the slave address is set to ‘1’. There are three basic types of read operations: current address read, random read and sequential read. 8.1 Current Address Read The 24VL024/24VL025 contains an address counter that maintains the address of the last word accessed, internally incremented by one. Therefore, if the previous read access was to address n, the next current address read operation would access data from address n + 1. Upon receipt of the slave address with the R/W bit set to ‘1’, the 24VL024/24VL025 issues an acknowledge and transmits the 8-bit data word. The master will not acknowledge the transfer, but does generate a Stop condition and the 24VL024/24VL025 discontinues transmission (Figure 8-1). 8.2 Random Read Random read operations allow the master to access any memory location in a random manner. To perform this type of read operation, the word address must first be set. This is done by sending the word address to the 24VL024/24VL025 as part of a write operation. FIGURE 8-1: Once the word address is sent, the master generates a Start condition following the acknowledge. This terminates the write operation, but not before the internal Address Pointer is set. The master then issues the control byte again but with the R/W bit set to a ‘1’. The 24VL024/24VL025 will then issue an acknowledge and transmits the eight-bit data word. The master will not acknowledge the transfer, but does generate a Stop condition and the 24VL024/24VL025 discontinues transmission (Figure 8-2). After this command, the internal address counter will point to the address location following the one that was just read. 8.3 Sequential Read Sequential reads are initiated in the same way as a random read except that after the 24VL024/24VL025 transmits the first data byte, the master issues an acknowledge as opposed to a Stop condition in a random read. This directs the 24VL024 to transmit the next sequentially addressed 8-bit word (Figure 8-3). To provide sequential reads, the 24VL024/24VL025 contains an internal Address Pointer which is incremented by one at the completion of each operation. This Address Pointer allows the entire memory contents to be serially read during one operation. The internal Address Pointer will automatically roll over from address FFh to address 00h. CURRENT ADDRESS READ Bus Activity Master S T A R T SDA Line S Bus Activity © 2009 Microchip Technology Inc. Control Byte S T O P Data P A C K N O A C K DS22130A-page 11 24VL024/24VL025 FIGURE 8-2: Bus Activity Master SDA Line RANDOM READ S T A R T Control Byte S Bus Activity Master Control Byte S T O P Data (n) P S A C K A C K Bus Activity FIGURE 8-3: S T A R T Word Address (n) N O A C K A C K SEQUENTIAL READ Control Byte Data (n) Data (n + 1) Data (n + 2) S T O P Data (n + X) P SDA Line Bus Activity DS22130A-page 12 A C K A C K A C K A C K N O A C K © 2009 Microchip Technology Inc. 24VL024/24VL025 9.0 PACKAGING INFORMATION 9.1 Package Marking Information 8-Lead PDIP (300 mil) Example: 24VL024 P e3112F 0821 XXXXXXXX T/XXXNNN YYWW 8-Lead SOIC (3.90 mm) XXXXXXXT XXXXYYWW NNN 8-Lead TSSOP Example: 24VL024 SN e3 0821 12F Example: XXXX 4V24 TYWW 821 NNN 12F 8-Lead MSOP Example: XXXXXT 4V24 YWWNNN 82112F 8-Lead 2x3 TDFN XXX YWW NN 6-Lead SOT-23 XXNN © 2009 Microchip Technology Inc. Example: AP9 821 12 Example: HF12 DS22130A-page 13 24VL024/24VL025 1st Line Marking Codes Part Number TSSOP MSOP TDFN SOT-23 24VL024 4V24 4V24 AP9 — 24VL025 4V25 4V25 AR6 HFNN Legend: XX...X T Y YY WW NNN e3 Note: Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion. *Standard OTP marking consists of Microchip part number, year code, week code, and traceability code. DS22130A-page 14 © 2009 Microchip Technology Inc. 24VL024/24VL025 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 6&! '! 9'&! 7"') %! 7,8. 7 7 7: ; < & & & = = ##44!! - 1!& & = = "#& "#>#& . - - ##4>#& . < : 9& -< -? & & 9 - 9#4!! < ) ? ) < 1 = = 69#>#& 9 *9#>#& : *+ 1, - !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#/!# '! #& .0 1,21!'! &$& "! **& "&& ! * ,<1 © 2009 Microchip Technology Inc. DS22130A-page 15 24VL024/24VL025 ! ""#$%& !' 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D e N E E1 NOTE 1 1 2 3 α h b h A2 A c φ L A1 L1 6&! '! 9'&! 7"') %! β 99.. 7 7 7: ; < & : 8& = 1, = ##44!! = = &# %%+ = : >#& . ##4>#& . -1, : 9& 1, ?1, ,'%@ & A = 3 &9& 9 = 3 && 9 .3 3 & I B = <B 9#4!! = 9#>#& ) - = #%& D B = B #%&1 && ' E B = B !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,1 DS22130A-page 16 © 2009 Microchip Technology Inc. 24VL024/24VL025 ! ""#$%& !' 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 © 2009 Microchip Technology Inc. DS22130A-page 17 24VL024/24VL025 () )"* ! (+%+( ! 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D N E E1 NOTE 1 1 2 b e c A φ A2 A1 L L1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; < & : 8& = ?1, = ##44!! < &# %% = : >#& . ##4>#& . - ?1, ##49& - - 3 &9& 9 ? 3 && 9 .3 3 & I B = <B 9#4!! = 9#>#& ) = - !"#$%&"' ()"&'"!&) &#*&&&# '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# - '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,<?1 DS22130A-page 18 © 2009 Microchip Technology Inc. 24VL024/24VL025 ," ! *-, , ! 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D N E E1 NOTE 1 1 2 e b A2 A c φ L L1 A1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; < & : 8& = ?1, = ##44!! < &# %% = : >#& . ##4>#& . -1, : 9& -1, 3 &9& 9 3 && 9 1, ? < .3 3 & B = <B 9#4!! < = - 9#>#& ) = !"#$%&"' ()"&'"!&) &#*&&&# '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# - '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,1 © 2009 Microchip Technology Inc. DS22130A-page 19 24VL024/24VL025 . $*-,/00%12(. 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 DS22130A-page 20 © 2009 Microchip Technology Inc. 24VL024/24VL025 . $*-,/00%12(. 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 © 2009 Microchip Technology Inc. DS22130A-page 21 24VL024/24VL025 3 ! (""!( !(/ 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 b 4 N E E1 PIN 1 ID BY LASER MARK 1 2 3 e e1 D A A2 c φ L A1 L1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; ? & 1, :"&!#9#& 1, : 8& = ##44!! < = - &# %% = : >#& . = - ##4>#& . - = < : 9& = - 3 &9& 9 = ? 3 && 9 - = < 3 & B = -B 9#4!! < = ? 9#>#& ) = '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# '! #& .0 1,2 1!'! &$& "! **& "&& ! * ,<1 DS22130A-page 22 © 2009 Microchip Technology Inc. 24VL024/24VL025 REVISION HISTORY Revision A (01/2009) Original release. © 2009 Microchip Technology Inc. DS22130A-page 23 24VL024/24VL025 NOTES: DS22130A-page 24 © 2009 Microchip Technology Inc. 24VL024/24VL025 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives • • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2009 Microchip Technology Inc. DS22130A-page 25 24VL024/24VL025 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Device: 24VL024/24VL025 Y N Literature Number: DS22130A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS22130A-page 26 © 2009 Microchip Technology Inc. 24VL024/24VL025 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X /XX Temperature Range Device: 24VL024: 24VL024T: 24VL025: 24VL025T: Temperature Range: = Package 1.5V, 2 Kbit Addressable Serial EEPROM 1.5V, 2 Kbit Addressable Serial EEPROM (Tape and Reel) 1.5V, 2 Kbit Addressable Serial EEPROM, with no WP pin 1.5V, 2 Kbit Addressable Serial EEPROM (Tape and Reel), with no WP pin Examples: a) b) c) d) e) f) g) -20°C to +85°C h) Package: Note P SN ST MS MNY(1) OT 1: 24VL024/P: 1.5V, PDIP Package. 24VL024/SN: 1.5V, SOIC Package. 24VL024T/ST: 1.5V, TSSOP Package, Tape and Reel 24VL024T/MNY: 1.5V, TDFN Package, Tape and Reel 24VL025/P: 1.5V, PDIP Package. 24VL025/SN: 1.5V, SOIC Package. 24VL025T/ST: 1.5V, TSSOP Package, Tape and Reel 24VL025T/MNY: 1.5V, TDFN Package, Tape and Reel = = = = = = Plastic DIP, (300 mil Body), 8-lead Plastic SOIC, (3.90 mm Body) TSSOP, (4.4 mm Body), 8-lead MSOP, (Plastic Micro Small Outline), 8-lead TDFN, (2x3x0.75 mm Body), 8-lead Plastic Small Outline (SOT-23), 6-lead (Tape and Reel only) “Y” indicates a Nickel Palladium Gold (NiPdAu) finish. © 2009 Microchip Technology Inc. DS22130A-page 27 24VL024/24VL025 NOTES: DS22130A-page 28 © 2009 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC, SmartShunt and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2009 Microchip Technology Inc. DS22130A-page 29 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 01/16/09 DS22130A-page 30 © 2009 Microchip Technology Inc.