CREE LP379THR1-C0G

Cree® P4 LED
Model # LP379THR1-C0G
Data Sheet
120-degree, 7.6 x 7.6 mm LED lamp in high-red color with water-transparent lens and stopper
Applications
•
•
•
Advertising Signs
Indicators
Automotive Lighting
Absolute Maximum Ratings (TA = 25°C)
Items
Symbol
Absolute Maximum Rating
Unit
IF
70
mA
IFP
200
mA
Reverse Voltage
VR
5
V
Power Dissipation
PD
220
mW
Operation Temperature
Topr
-40 ~ +100
°C
Storage Temperature
Tstg
-40 ~ +100
°C
Lead Soldering Temperature
Tsol
Forward Current
Note 2
Peak Forward Current
Note 1
Max. 260°C for 3 sec. max.
(3 mm from the base of the epoxy bulb)
Notes:
1.
2.
Pulse width ≤0.1 msec, duty ≤1/10.
A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C.
D-CT135.000
Data Sheet: CL
Typical Electrical & Optical Characteristics (TA = 25°C)
Characteristics
Symbol
Condition
Unit
Forward Voltage
VF
IF = 70 mA
V
Reverse Current
IR
VR = 5 V
μA
Dominant Wavelength
λD
IF = 70 mA
nm
620
628
Luminous Flux
ΦV
IF = 70 mA
mlm
3000
4000
2θ½
IF = 70 mA
deg
50% Power Angle
Minimum
Subject to change without notice.
www.cree.com/ledlamps
Typical
Maximum
2.6
3.2
100
637
120
Standard Bins for LP379THR1-C0G (IF = 70 mA)
Lamps are sorted to luminous flux (ΦV), VF and dominant wavelength (λD) bins shown.
Orders for LP379THR1-C0G may be filled with any or all bins contained as below.
All luminous flux (ΦV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA.
M or
above
L
K
J
620 nm
637 nm
Dominant Wavelength (λD)
Rank
Luminous Flux
J
K
L
3000-4200 mlm
3500-4800 mlm
4000-6100 mlm
Forward Voltage (VF)
Rank
Voltage
V4
V5
V6
V7
V8
2.2-2.4 V
2.4-2.6 V
2.6-2.8 V
2.8-3.0 V
3.0-3.2 V
Important Notes:
1. All ranks will be included per delivery; rank ratio will be based on the dice distribution.
2. No tolerance of measurement of luminous flux.
3. Tolerance of measurement of dominant wavelength is ±1 nm.
4. Tolerance of measurement of VF is ±0.05 V.
5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document.
6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions.
7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED
product safely.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
CLD-CT135.000
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Model No.
Doc. No.
LP379THR1-C0G
06 13Oct04
Graphs
Graphs
100.0
-50
-60
Vr(V)
If (mA)
-40
-20
-30
-10
0.0
80.0
-10.0
60.0
-20.0
40.0
-30.0
20.0
-40.0
0.0
2.0
2.2 2.4
2.6 2.8 3.0
FIG.1 FORWARD CURRENT VS.
FORWARD VOLTAGE.
Vf(V)
Half Power
WL=23nm
Domi WL= 628nm
I (RELATIVE LUMINOUS FLUX)
100%
2.5
2.0
75%
1.5
50%
1.0
25%
0.5
If(mA)
0.0
0.0
20.0 40.0 60.0 80.0 100.0
FIG.3 RELATIVE LUMINOUS FLUX VS.
FORWARD CURRENT.
100
-50.0
Ir(uA)
FIG.2 REVERSE CURRENT VS.
REVERSE VOLTAGE.
WL(nm)
500 600 700 800 900
FIG.4 RELATIVE LUMINOUS FLUX VS.
WAVELENGTH.
0%
400
IF(mA)
50% Power Angle : 120
Ie(%)
80
0
100%
60
80%
40
60%
20
0
40%
Ta( C)
0
20
40
60
80
100
FIG.5 MAXIMUM FORWARD DC CURRENT VS
AMBIENT TEMPERATURE (Tjmax=120 C)
Items
20%
120
0%
-90
-60
-30
0
30
60
90
FIG.6 FAR FIELD PATTERN
Signatures
Date
Revision History
Prepared by
LiuZM
2004/10/13
DOC. No.
Checked by
AldosinLi
2004/10/13
D 08Oct03
Approved by
David
2004/10/13
05 23Sep04
Add ESD and Notes; Change FIG.1&3&5; Change ĭV & OD Rank form.
ECN#
ECN-H20040276
06 13Oct04
OD(max) from 635nm to 637nm.
CHANGE DESCRIPTION
PD from 150mW to 220mW. Change FIG.5
Data is subject to change without prior notice.
[email protected] Cotco International Ltd.
Obsoletes Doc: 05 23Sep04.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
CLD-CT135.000
4/4
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
COTCO-D-074
REV.1
Mechanical Dimensions
Model No.
Doc. No.
LP379THR1-C0G
06 13Oct04
All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted.
An epoxy meniscus may extend about 1.5 mm down the leads.
Burr around bottom of epoxy
mm
Dimmay
ensbeio0.5
nD
ramax.
wing
maximum
Unit
ating
70
mA
00
mA
5
V
20
mW
~ +100
°C
~ +100
°C
Notes
0°C for 5 sec Max.
e base of
theCompliance
epoxy bulb)
RoHS
The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or
otherwise restricted materials in this product are below the maximum concentration values (also referred to as the
the device
is operated
at ambient
temperatures
deg C.application,
For long in
term
threshold
limits) permitted
for such
substances, or higher
are usedthan
in an25
exempted
accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment
and 50mA
are recommended. Please contact COTCO sales representative for more
(RoHS), as amended through April 21, 2006.
Vision Advisory Claim
Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
cs ( Ta = 25°C)
Condition
Min.
Typ.
Max.
Unit
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
IF = 70mA
---
CLD-CT135.000
2.6
3.2
V
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps
Kit Number System
Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage,
and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED
Lamp Packaging Standard” document for more information about shipping and packaging options.
Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following
manner:
Standard/Custom
0: Standard
C: Custom
VF
0: Full forward voltage distribution
1~9, A~Z . . . : special request *
Wd/Color
1: Full-color distribution
2~9, A~Z . . . : special request *
aaaaaaaaa-aaa-aa- x x x x x
IV
0: Full luminous intensity distribution
1~9, A~Z . . . : special request *
Packing type
0: Standard = tube pack
1~9, A~Z . . . : special request *
Product P/N
* Contact your Cree sales representative for ordering information.
Standard Available Kits*
Kit Number
Description
LP379THR1-C0G-00001
P4 120 High Red 628nm, FULL RANK, Tube Pack
LP379THR1-C0G-00011
P4 120 High Red 628nm, K or above, Tube Pack
* Please contact your Cree representative about the availability of non-standard kits.
Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
CLD-CT135.000
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Fax: +1.919.313.5778
www.cree.com/ledlamps